KOSTA’S BIG JOHN’S 776 SECTION 087100 PART 1 … · KOSTA’S BIG JOHN’S 776 SECTION 087100...

KOSTA’S BIG JOHN’S 776 SECTION 087100 FINISH HARDWARE

JOB #1319 087100-1

PART 1 GENERAL 1.1 SUMMARY A. Work under this section includes the complete finish hardware requirements for the project. Quantities listed are for the contractor’s convenience only and are not guaranteed. Items not specifically mentioned, but necessary to complete the work shall be furnished, matching the items specified in quality and finish. B. Related Sections:

1. Section 08110 Metal Doors and Frames 2. Section 08410 Aluminum Doors and Frames

1.2 QUALITY ASSURANCE A. Product Qualification:

1. To assure a uniform high quality of materials for the project, it is intended that only specified items be furnished. Comparable products may be accepted upon prior approval of architect.

2. Hardware to be new, free of defects, blemishes and excessive play. Obtain each kind of hardware (Mechanical latch and locksets, exit devices, hinges and closers) from one manufacturer except where specified.

3. Fire-Rated opening in compliance with NFPA80. Hardware UL10C/UBC-7-2 (positive pressure) compliant for given type/size opening and degree of label. Provide proper latching hardware, non-flaming door closers, approved bearing hinges and smoke seal. Furnish openings complete.

B. Supplier Qualifications

1. Hardware supplier will be a direct factory contract supplier who employs a certified architectural hardware consultant (AHC) available at all reasonable times during the course of the work for project hardware consultation to owner, architect and contractor.

2. Supplier will be responsible for detailing, scheduling and ordering of finish hardware.

3. Conduct pre-installation conference at jobsite. Initiate and conduct with supplier, installer and related trades. Coordinate materials and techniques and sequence complex hardware items and systems installation.

4. Key Conference shall be initiated and conducted with owner to determine system, keyway(s) and structure.

C. Installer Qualifications:

1. Installer to have not less than 3 years experience specializing in installation of work in this section. Company must maintain qualified personnel trained and experienced in installing hardware.

1.3 REFERENCES

A. NFPA80 – Fire Doors and Windows B. NFPA101 – Life Safety Code C. NFPA105 – Smoke and Draft Control Door Assemblies D. ANSI A117.1 Specifications for making Buildings usable by physically

handicapped people.


JOB #1319 087100-2

1.4 SUBMITTALS A. Hardware schedule: Submit 6 copies of schedule. Organize vertically formatted

schedule into Hardware Sets with index of doors and headings, indication complete designations of every item required for each door or opening. Include the following:

1. Type, style, function, size, quantity and finish of hardware items. 2. Name, part number and manufacture of each item. 3. Fastenings and other pertinent information. 4. Explanation of abbreviations, symbols and codes contained in schedule. 5. Door and frame sizes, materials and degrees of swing. B. Product Data: Submit 4 copies for each product indicated. C. Templates: Obtain and distribute templates for doors, frames, and other works specified to be prepared for installing door hardware. D. Wiring/Riser diagrams: as required for electric hardware indicated. E. Maintenance Data: For each type of door hardware to include in maintenance manuals specified in Division 1 F. Keying Schedule: Prepared by or under the supervision of supplier, after receipt of the approved finish hardware schedule, detailing Owner’s final keying instructions for locks. G. Samples: Upon request submit material samples. 1.5 DELIVERY, STORAGE AND HANDLING A. Deliver, store, handle and protect products to project site under provisions of Division 1 and as specified herein B. Tag each item or package separately, with identification related to the final Door Hardware Schedule, and include basic installation instructions with each item or package. C. Deliver keys to Owner by registered mail. 1.6 WARRANTY A. The finish hardware shall have a limited warranty against defects in workmanship and operation for a period of one year from date of substantial completions and the following items are as shown: 1. Closers Ten years mechanical, two years electrical. 2. Exit Devices: Three years 3. Locksets Seven years PART 2 PRODUCTS 2.1 MATERIAL AND FABRICATION A. Provide all door hardware for complete work, in accordance with the drawings and as specified herein. B. Provide items and quantities not specifically mentioned to ensure a proper and complete operational installation.


JOB #1319 087100-3

2.2 MANUFACTURERS:

A. Any item shown in the hardware schedule, but not listed below shall be supplied as shown unless otherwise approved by the Architect.

ITEM: MANUFACTURER: ACCEPTABLE SUB: Hinges (IVES) Ives McKinney, Hager Double acting hinges (BOM) Bommer Locks (SCH) Schlage None Keying (SCH) Schlage None Exit Devices (VON) Von Duprin None Closers (LCN) LCN None Silencers (IVE) Ives Hager, Trimco Kickplates (IVE) Ives Hager, Trimco Stops & Holders (IVE) Ives Hager, Trimco Overhead Stops (GLY) Glynn-Johnson Rixon Threshold (NGP) National Guard Pemko Seals & Bottom (NGP) National Guard Pemko 2.3 HANGING A. Conventional Hinges: Hinge open width minimum, but of sufficient throw to permit maximum door swing. Steel or stainless steel pins.

1. Three hinges per leaf to 7 feet, 6-inch height. Add one for each additional 30 inches in height or any fraction thereof.

2. Provide 4 ½ x 4 ½ for 1 ¾” thick doors up to 36”. Provide 5 x 4 ½ on doors over 36”.

3. Exterior outswing doors to have non removable (NRP) pins. 4. Pin tips, flat button, finish to match leaves 5. Interior doors over 36” – Heavy weight 6. Interior doors up to 36” – Standard weight

2.4 LOCKSETS, LATCHSETS, DEADBOLTS

A. Extra Heavy Duty Cylindrical Locks and Latches: as scheduled.

1. ANSI A156.2 Series 4000, Grade 1 Strength and Operational requirements. a. UL listed for A label and lesser class single doors up to 4ft x 8ft.

2. Meets A117.1 Accessibility Codes. 3. Latch bolts shall be steel with minimum ½” throw, deadlocking on keyed and

exterior functions. ¾” throw anti-friction latch bolt on pairs of fire doors. 4. Lock case steel. 5. Lock shall incorporate one piece spring cage and spindle. 6. Locksets to be tested to exceed 3,000,000 cycles. 7. Strikes: 16 gage curved steel, bronze or brass with 1” deep box construction, lips

of sufficient length to clear trim and protect clothing. 8. Provide seven year warranty. 9. Lock Series and Design: Schlage ND series, “Rhodes” design.

2.5 EXIT DEVICES

A. General features:

1. Independent lab-tested 1,000,000 cycles.


JOB #1319 087100-4

2. Push-through touch pad design. No exposed touch bar fasteners, no exposed cavities when operated. Return stroke fluid dampeners and rubber bottoming dampeners, plus anti-rattle devices.

3. ¾” throw deadlocking latchbolts. 4. No exposed screws to show through glass doors. 5. Non-handed basic device design with center case interchangeable with all

functions, no extra parts required to effect change of function. 6. Releasable with 32 lb. maximum pressure under 250 lb. load to the door.

2.6 KEYS, KEYING, AND KEY CONTROL See Keying Requirements in this section. 2.7 CLOSERS

A. Surface Closers: [4010/4111]

1. Full rack-and-pinion type cylinder with removable non-ferrous cover and cast iron body. Double heat-treated pinion shaft, single piece forged piston, chrome-silicon steel spring.

2. ISO 2000 certified. Units stamped with date-of-manufacture code. 3. Independent lab-tested 10,000,000 cycles. 4. Thru-bolts and wood doors unless doors are provided with closer blocking.

Non-sized and adjustable. Place closers inside building, stairs and rooms. 5. Plates, brackets and special templating when needed for interface with particular

header, door and wall conditions and neighboring hardware. 6. Opening pressure: Exterior doors 8.5 lb., interior doors 5 lb., labeled fire doors

15 lb. 7. Separate adjusting valves for closing speed, latching speed and backcheck,

fourth valve for delayed action where scheduled. 8. Extra-duty arms (EDA) at exterior doors scheduled with parallel arm units. 9. Exterior door closers: tested to 100 hours of ASTM B117 salt spray test, furnish

data on request. 10. Exterior doors do not require seasonal adjustments in temperatures from 120

degrees F to –30 degrees F, furnish data on request. 11. Non-flaming fluid will not fuel door or floor covering fires.

2.8 OTHER HARDWARE A. Door stops: Provide stops to protect walls, casework or other hardware. 1. Except as otherwise indicated, provide stops (wall, floor or overhead) at each leaf of every swinging door leaf. 2. Where wall or floor stops are not appropriate, provide overhead holders. B. Weatherstrip and Gasket 1. Provide continuous weather-strip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated or scheduled. 2. Provide non-corrosive fasteners as recommended by the manufacturer for application indicated. C. Thresholds 1 Except as otherwise indicated, provide standard metal threshold unit of type, size and profile as detailed or scheduled. D. Silencers 1. Interior hollow metal frames, 3 for single doors, 4 for pairs of doors.


JOB #1319 087100-5

E. Kick Plates: 1. Four beveled edges, .050 inches minimum thickness, height and width as scheduled. Sheet-metal screws of bronze or stainless steel to match other hardware. 2.9 HARDWARE FINISH A. Provide the following finishes unless noted differently in hardware groups. Hinges, Exterior 630 Stainless Steel, Interior 626 Dull Chrome Locksets Exterior 630 Stainless Steel, Interior 626 Dull Chrome Exit Devices 630 Stainless Steel Closers Alum 689 Kickplates Stainless Steel Other hardware 626 Dull Chrome Thresholds ALUMINUM Weatherstrip/sweeps ALUMINUM 2.10 KEYING REQUIREMENTS A. All keyed cylinders shall be subject to a new Schlage Masterkey system. B. Furnish cylinders with construction cores. Following construction supply permanent keyed cores. C. Cylinders to be furnished with visual key control with key code. Stamped on the face of the keys and marked on the back or side of the cylinders. D. Key Quantities

6 each MKs 6 ea Construction keys 3 each Change keys per keyed alike group

PART 3 EXECUTION 3.1 ACCEPTABLE INSTALLERS: A. Factory trained, certified, and carries a factory-issued card certifying that person as a “Certified Installer”. Alternative: can demonstrate suitably equivalent competence and experience. 3.2 PREPARATION: A. Ensure that walls and frames are square and plumb before hardware installation. B. Locate hardware per SDI-100 and applicable building, fire, life-safety, accessibility, and security codes. Notify Architect of any code conflicts before ordering materials. 3.3 INSTALLATION A. Install hardware per manufacturer’s instructions and recommendations. Do not install surface mounted items until finishes have been completed on substrate. Set units level, plumb and true to line and location. Adjust and reinforce attachment substrate for proper installation and operation.


JOB #1319 087100-6

B. Locate floor stops not more than 4 inches from the wall. C. Drill pilot holes for fasteners in wood doors and/or frames. 3.4 ADJUSTING A. Adjust and check for proper operation and function. Replace units, which cannot be adjusted to operate freely and smoothly. B. Hardware damaged by improper installation or adjustment methods to be repaired or replaced to Owner’s satisfaction. 3.5 FOLLOW UP INSPECTION A. Installer to provide letter of agreement to Owner that approximately 6 months after substantial completion, installer will visit project with representative of the manufacturers of the locking devices and door closers to accomplish the following: 1. Re-adjust locks and closers 2. Evaluate maintenance procedures and recommend changes or additions, and instruct Owner’s personnel. 3. Identify items that have deteriorated or failed. 4. Submit written report identifying problems and likely future problems. 3.6 DEMONSTRATION A. Demonstrate electrical, electronic and pneumatic hardware system including adjustment and maintenance procedures 3.7 PROTECTION/CLEANING A. Cover installed hardware, protect from paint, cleaning agents, weathering, carts/barrows, etc. Remove covering materials and clean hardware just prior to substantial completion. Clean adjacent wall, frame and door surfaces soiled from installation/reinstallation process. 3.8 DOOR HARDWARE GROUPS

HW 01

6 EA HW HINGE 5BB1HW 4.5 X 4.5 NRP 630 IVE 1 EA PANIC HARDWARE 3547A-EO 626 VON 1 EA PANIC HARDWARE 3547A-NL-OP-388 626 VON 1 EA RIM CYLINDER 20-057 626 SCH 2 EA 90 DEG OFFSET PULL 8190 10" O 630 IVE 2 EA OH STOP 100S 630 GLY 2 EA SURFACE CLOSER 4111 AVB SCUSH SRI 689 LCN 1 EA CUSH SHOE SUPPORT 4110-30 689 LCN 1 EA BLADE STOP SPACER 4110-61 689 LCN 2 EA DOOR SWEEP C627A CL NGP 1 EA THRESHOLD 8424 MS/LA AL NGP 1 EA WEATHERSTRIP BY DOOR/FRAME

MANUFACTURER


JOB #1319 087100-7

HW 02

6 EA HW HINGE 5BB1HW 4.5 X 4.5 NRP 630 IVE 2 EA MANUAL FLUSH BOLT FB458 626 IVE 1 EA DUST PROOF STRIKE DP2 626 IVE 1 EA STOREROOM LOCK L9080P 06A 10-072 7/8" LIP 630 SCH 2 EA OH STOP 100S 630 GLY 2 EA SURFACE CLOSER 4111 AVB SCUSH SRI 689 LCN 1 EA CUSH SHOE SUPPORT 4110-30 689 LCN 1 EA BLADE STOP SPACER 4110-61 689 LCN 1 EA HEAD SEAL 706A AL NGP 1 SET SEALS 9706E

at jambs AL NGP

1 EA ASTRAGAL 139SP 600 NGP 2 EA DOOR SWEEP C627A CL NGP 1 EA THRESHOLD 8429 MS/LA AL NGP

HW 03

3 EA SPRING HINGE 3029-6 652 BOM 2 EA PUSH PLATE 8200 4" X 16" 630 IVE 1 EA OH STOP 100S

Double acting 630 GLY

2 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE

HW 04

3 EA HW HINGE 5BB1HW 5 X 4.5 652 IVE 1 EA STOREROOM LOCK ND80PD RHO 626 SCH 1 EA SURFACE CLOSER 4011 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE 1 EA WALL STOP WS401CCV 626 IVE

HW 05

3 EA HINGE 5BB1 4.5 X 4.5 652 IVE 1 EA ENTRANCE LOCK ND53PD RHO 626 SCH 1 EA WALL STOP WS401CCV 626 IVE 1 SET SEALS 5050B BRN NGP 1 EA DOOR SWEEP 200NA CL NGP 1 EA THRESHOLD 425 MS/LA AL NGP

HW 06

3 EA HINGE 5BB1 4.5 X 4.5 652 IVE 1 EA PRIVACY LOCK ND40S RHO 626 SCH 1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE 1 EA WALL STOP WS401CCV 626 IVE 3 EA SILENCER SR64 GRY IVE


JOB #1319 087100-8

HW 07

3 EA HINGE 5BB1 4.5 X 4.5 652 IVE 1 EA STOREROOM LOCK ND80PD RHO 626 SCH 1 EA KICK PLATE 8400 10" X 2" LDW B4E 630 IVE 1 EA WALL STOP WS401CCV 626 IVE 3 EA SILENCER SR64 GRY IVE

***END OF SECTION***

18

100 Series Concealed Overhead Door Holders/Stops

100 Series Heavy-DutyGlynn-Johnson offers a complete line of overhead door holders andstops, accommodating virtually all openings with solutions for eventhe most complex door control problems. These concealed holdersand stops provide the most attractive and reliable heavy-duty doorcontrol available.

Glynn-Johnson 100 series holders and stops provide the most reli-able and versatile concealed overhead door control. They aredesigned for installation on virtually all types of doors mounted onconventional type butt hinges, pivots, continuous hinges, swingclear hinges and numerous other specialty hinges. When used inconjunction with many surface-applied door closers, 100 seriesholders and stops provide the most effective control for entrancedoors and vestibule doors of all types, as well as heavy or oftenused interior doors. Templates provided allow for variable mountingpositions, ranging from 85° - 110° of opening.

Five Models: • 100H Series Hold-Open Model• 100HP Series Internal Hold-Open Model• 100F Series Friction Hold-Open Model• 100S Series Stop-Only Model• 100SE Series Special Stop-Only Model

Six Sizes:• Each model comes in six sizes.• Simple• Standardized

Three Options:• ADJ—Adjustable Jamb Bracket• CJ—Jamb Bracket for use with LCN5030 Closer• SOC—Pin-in-Socket Security Screw Package

Unmatched Convenience:• Non-handed• Improved Compatibility with Door Closers• Single/Double-Acting Doors• Interior/Exterior Applications• Reduced Door Prep• Durable• Improved Corrosion Resistance• Function Conversion Kits are Available.

Materials and Finishes:In Heavy Gauge Brass or 300 Series Stainless Steel, these modelsoffer the broadest range of finishes in the industry, complementingany design and offering the highest resistance to corrosion.Available in the following finishes:

Finishes DescriptionUS3 Polished BrassUS4 Satin BrassUS10 Satin BronzeUS10B Oil Rubbed BronzeUS32 Polished Stainless SteelUS32D Satin Stainless SteelSP4 Powder Coat BrassSP10 Powder Coat BronzeSP28 Powder Coat AluminumSP313 Powder Coat Dark BronzeSPBLK Powder Coat Black

ModelsThese models provide a wide range of optional features, and areideal for use on entrance and vestibule doors, large doors, doorsopened frequently, or doors subject to abuse. These models are alsofurnished with an offset-style jamb bracket.

Designed for heavy-duty applications, 100 series models will provide long-lasting protection to doors, frames, hinges, relatedhardware and surrounding walls or obstructions.

100H Series Hold-Open(Suffix H) The Hold-Open function should be used where it is desired to hold a door open at a predetermined position for short or long periods of time, permitting an unobstructed traffic flow through the opening.

These models are both selective and adjustable, featuring the most reliable Hold-Open mechanism available. They feature a control knob which protrudes from the face of the door and turns the Hold-Open function on or off. Set in the inactive position, the unit acts as a stop and shock absorber. The tension on the Hold-Open mechanism can be adjusted using an allenwrench to offset air currents or other exterior conditions. TheHold-Open tension adjustment is located in the bottom of the track in the top of the door.

100HP Series Internal Hold-OpenThese models provide a Hold-Open unit with the Hold-Open mechanism built into the channel, thus reducing the door prep. The 100HP have a preset Hold-Open force that is not adjustable. The Hold-Open feature is not selectable in these units, so the doorsare always held open.

gerickso

Oval

gerickso

Oval

19

100F Series Friction Hold-Open (Suffix F) Friction Hold-Open models provide an alternative holding method, ideal for heavy patient room doors, closet doors or similar applications where multiple Hold-Open positions are desired. The friction tension is adjusted using an allen wrench and an open end wrench. The friction tension adjustment is located on the top of the slider in the channel.

100S Series Stop-Only(Suffix S) When the Hold-Open function is not required, the Stop-Only function provides the same effective door control minus the Hold-Open feature. The Stop-Only model may be used on fire doors.

100SE Series Special Stop-Only(Suffix SE) When Stop-Only models are used in conjunction withsingle point Hold-Open electronic door closers, they may be orderedwithout the shock-absorbing mechanism. Used as an auxiliary stopwith these closers, they will prolong the life of the closer. The stoplocation is adjusted using an allen wrench on the stop block locatedin the channel.

Note: Caution should be used when using this option in other applications, as the elimination of the shock-absorbing spring can put added stress on doorand frame if used improperly.

Application InformationUL ClassificationThe 100 series Stop-Only models are classified by UnderwritersLaboratories (UL) as Miscellaneous Fire Door Accessories. Thisclassification applies to use on either Hollow Metal Fire Doors orWood Fire Doors. Where Wood Door manufacturer’s listing allowsfor the cutout required for installation, concealed overhead stopsmay be used on those wood fire doors. These units may be used ondoors of any rating. As a reminder, the Miscellaneous Fire DoorAccessories (GVUX) section is defined by UL as: “Miscellaneousfire door accessories are intended in the individual Listings. Theaccessories have been investigated to determine that when installedin accordance with the manufacturer’s instructions, the accessoriesdo not adversely affect the fire rating of the fire door and/or firedoor frames.”

Dead Stop Templating: If a wall or similar obstruction is in place at 110° or less openingangle (i.e. doors that open back-to-back), Dead Stop Templatingshould be used. This includes all Hold-Open, Friction and Stop-Only models, except when the “SE” Option is used. The Dead Stop position is reached when the shock-absorbing spring is fully compressed, the initial degree of opening will be 5° to 7°less than the Dead Stop opening.

Example: If the holder is templated to 100° Dead Stop, the door will hold opensomewhere between 93° and 95°, but no further than 100°.

Note: Do not use dead-stop templating on the 100SE Series since there is noshock-absorbing spring.

Environmental Considerations:Environmental factors should always be considered when specifying overhead holders and stops. Doors that are positioned on a building’s exterior or subject to corrosive conditions should be equipped with a holder constructed primarily of stainless steel or brass materials. For interior applications, steel is acceptable,though brass substrates generally provide a more attractive architectural-grade finish.

Function Conversion Kits• FK100F—Converts a 100H or 100S unit into a 100F unit.

To order specify FK100F.• FK100H—Converts a 100F or 100S unit into a 100H unit.

To order specify FK100H.• No kit is needed to convert a 100H or 100F unit

into a 100S unit.

OptionsSuffix ADJ (Adjustable Jamb Bracket):An additional option on the 100 series is the adjustable jamb bracket,which allows the degree of Hold-Open or Stop angle to be adjustedafter installation. Suffix “ADJ” is available in all functions, but onlyin sizes 3, 4, 5 & 6. ADJ jamb bracket requires additional frame prep.The ADJ option cannot be added to an existing unit, it must be factory ordered.

Suffix CJ (Closer Jamb Bracket):Provides a special jamb bracket needed for 100 series units used withLCN5030 closers. These special jamb brackets are handed, so handingwill need to be specified when ordering the “CJ” option, CJLH fora left hand door and CJRH for a right hand door. The CJ optioncannot be added to an existing unit, it must be factory ordered.

Suffix SOC (Pin-in-Socket Security Screw Package):A screw package with pin-in-socket screws for mounting the jambbracket to the frame is provided instead of the standard screw package.

20

100 Series Concealed Overhead Door Holders/Stops

The template information on this page is for reference only and is not intended to serve as an installation template. For complete dimensional information, refer to Glynn-Johnson template book.

1-1/4"1"

1/4"

1-1/4"1"

2"

3/4"

3/8"

4-1/4"

1-1/4"

2-3/8" 5-1/2"

1/4"

3/4"

1"

1/4"

3-1/2"

1-1/4"

1/2"

3/8"

12"

BUTTS/OFFSET PIVOTS CENTER HUNG

DOOR STOP HOLD DOOR STOP HOLDSIZE OPENING ONLY OPEN FRICTION OPENING ONLY OPEN FRICTION

1 18"–23" 101S* 101H* 101F* ----- ---- ---- ----2 23-1/16"–27" 102S* 102H* 102F* ----- ----- ----- -----3 27-1/16"–33" 103S 103H 103F 33-1/16"–39" 103S 103H 103F 4 33-1/16"–39" 104S 104H 104F 39-1/16"–45" 104S 104H 104F5 39-1/16"–45" 105S 105H 105F 45-1/16"–51" 105S 105H 105F6 45-1/16"–54" 106S 106H 106F 51-1/16"–59" 106S 106H 106F

100 Series Sizing Chart

* First numeral (0) designates optional material.

To specify: Brass material, change 0 to 1 (i.e. C11511)Stainless Steel material, change 0 to 5 (i.e. C51511)

Note: This chart illustrates the most common types of hinging and door opening sizes. For unusual door details, contact Glynn-Johnson for availability.

*These sizes are not available for use with offset pivots. Also not available with the ADJ option.

BHMAAll 100 series models are designed for heavy-dutyapplications and far exceed BHMA cycle test andforce test requirements for Grade 1 holders and stops.

BHMA/ANSI, A156.8 & FED. Spec. Cross ReferenceG-J Model BHMA* FED. Spec.101-106 H C01511 1160101-106 S C01541 ----101-106 F C01531 ----

21

How to Order

Overhead Series:10

Size (Door Opening Using Butts or Offset Pivots:1 (18"–23")2 (23-1/16"–27")3 (27-1/16" –33")4 (33-1/16"–39")5 (39-1/16"–45")6 (45-1/16"–54")

Function:H Hold-OpenHP Internal Hold-OpenF Friction Hold-OpenS Stop-OnlySE Special Stop-Only

Finishes:US3 Polished BrassUS4 Satin BrassUS10 Satin BronzeUS10B Oil Rubbed BronzeUS32 Polished Stainless SteelUS32D Satin Stainless SteelSP4 Powder Coat BrassSP10 Powder Coat BronzeSP28 Powder Coat AluminumSP313 Powder Coat Dark BronzeSPBLK Powder Coat Black

Options:ADJ Adjustable Jamb BracketCJLH Special Jamb Bracket for LCN 5030 Closer, LH DoorCJRH Special Jamb Bracket for LCN 5030 Closer, RH DoorSOC Pin-in-Socket Security Screws

___ ___ ___ – ______ – ____10 4 H US26D ADJ

1

Architectural Door Trim

8103EZ Door Pull - Large 2-1/2" Clearance for the Physically ImpairedProd No. Proj. (A) Center to Center (B) Overall Length (C)

8103EZ 3-1/2" 8" 9"8103EZ 3-1/2" 10" 11"8103EZ 3-1/2" 12" 13"

How to Order8103EZ - - -

Size:8 for 8"0 for 10"2 for 12"

FinishesUS3, US4, US10, US10B, US26, US26D, US28, US32, US32D

Mounting Type:Blank StandardL Surface Concealed Two-Anchor M Back-To-Back with Spanner CollarN Back-to-Back Two-AnchorO Decorative Blind Thru-Bolt

8190 90° Offset Door PullProd No. Proj. (A) Center to Center (B) Overall Length (C)

8190 3-1/4" 8" 9"8190 3-1/4" 10" 11"8190 3-1/4" 12" 13"8190 3-1/4" 18" 19"

How to Order8190 - - -

Size:8 for 8"0 for 10"2 for 12"18 for 18"

FinishesUS3, US4, US10, US10BUS26, US26D, US32, US32D

Mounting Type:Blank StandardL Surface Concealed Two-Anchor M Back-To-Back with Spanner CollarN Back-to-Back Two-Anchor O Decorative Blind Thru-Bolt

gerickso

Oval

4

Mounting

Type NS-Standard Push/Pull MountingType N & Standard

Pushbar to Pull- (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws.- (1) steel screw sleeve, zinc plated.

Free End Pushbar & Pull- (2) 1/4-20 X 2-1/4" brass, oval head mach screws; plated to match.- (2) No. 14 countersunk washers; plated to match.

Type NO Push/Pull MountingType N & Type O

Pushbar to Pull- (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws.- (1) steel screw sleeve, zinc plated.

Free End Pushbar & Pull- (2) 1/4-20 X 2-1/4" blind thru-bolts; plated to match.

NOTES:* All mounting hardware is for standard 1-3/4" door.* Consult Customer Service if other than standard.

Architectural Door Trim

gerickso

Oval

A8

Manual Flush Bolts - Metal Doors

FB458, FB458N and FB0458N Series for Metal Doors• When the active door is opened, the lever can be moved to the ‘up’

position, retracting the bolt and allowing the inactive leaf to beopened. When the inactive leaf is closed, the lever can be moved tothe ‘down’ position, projecting the bolt into the strike and securelylocking the inactive leaf.

• Simplified installation in metal frames. Round bolt head requiresonly a punched hole. Use of strike optional. Special design of guideand flat sided bolt tip to prevent bolt rotation.

• FB458 UL Listed for Fire Doors.• FB458N and FB0458N not UL Listed for Fire Doors.• FB0458N features 1/4" radius corners on body.• Non-handed.

• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.• Bolt tip is 1/2" diameter.• Bolts have 3/4" throw with a bolt backset of 3/4".• Standard Rod Length is 12", which is measured from the center

of the flush bolt body to the bolt tip. • Meets ANSI/BHMA A156.16, L04251.• Optional Dust Proof Strikes— prevents dirt build-up assuring full

engagement of bottom bolt.• Optional Rod Lengths available for FB458: 6", 9", 18" and 24".• Optional Rod Lengths available for FB458N and FB0458N: 6", 9", 18",

24", 30", 36" and 48".

FB458Top or Bottom Bolt

• UL Listed 3 hours on 8'0" x 10'0" Opening

FB458NTop or Bottom Bolt

FB0458NTop or Bottom Bolt

Dimensions:Body Size: 1" Wide x 6-3/4" Long x 1-1/8" DeepGuide Size: 1" Wide x 2" Long x 5/64" ThickStrike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick

gerickso

Oval

gerickso

Oval

A9

Dust Proof Strikes

DP1 and DP2 Dust Proof Strikes• Designed for use with the bottom bolt of all flush bolts. • Spring-loaded plunger returns to floor or threshold level

anytime flush bolt is retracted, eliminating need to clean standard floor strikes.

• Meets ANSI/BHMA 156.16, L14011.• Finishes: US3, US4, US10, US10B, US26, US26D.

Dimensions:DP1 Face Plate: 1-7/16" DiameterDP2 Face Plate: 1-5/8" Wide x 3-1/2" Long x 1/8" ThickDP1 and DP2 Body: 1-3/16" Diameter x 1-7/8" Deep

DP1Threshold only.

DP2Floor and/or threshold.

DP3 and DP4 Dust Proof Strikes• Designed for use with the bottom bolt of the Ives extension flush

bolts on non-fire rated openings. DP3 for installation in thresholdsup to 1/4" thick. DP4 includes plate for installation in thresholds or floor.

• 3/4" diameter plunger accepts up to 5/8" diameter round bolts or1/2" square bolts.

• Can be locked in up position by rotating plunger with screwdriver or coin. Eliminates trapping of spiked heels.

• Made from polished wrought brass.• Brass Finishes: B3, B4, B5, B10, B10B, B14, B15, B15A, B26, B26D.

Dimensions:DP3 Faceplate: 1-3/8" DiameterDP4 Faceplate: 1-5/8" Wide x 3-1/2" Long x 1/8" thickDP3 and DP4 Body: 1-61/64" Overall Depth, Fits Hole

1-1/16" in Diameter

DP3Threshold only.

DP4Floor and/or threshold.

gerickso

Oval

gerickso

Oval

Wall Bumpers

D13

WS401 CVX & WS402 CVXWS401 CCV & WS402 CCVFeatures:• Constructed in heavy-duty cast brass or aluminum base.• Special retainer cup makes rubber tamper resistant.• The WS401CVX unit is designed with a convex rubber bumper, packed with wood screw and

plastic anchor.• The WS401CCV unit is designed with a concave rubber bumper which avoids damage to

locks with projecting buttons, packed with wood screw and plastic anchor.• The WS402CVX unit is designed with a convex rubber bumper packed with screw and

drywall anchor.• The WS402CCV unit is designed with a concave rubber bumper which avoids damage to

locks with projecting buttons and is packed with screw and drywall anchor.• WS401CVX & WS402CVX meets ANSI/BHMA 156.16 L12101 for brass and L32101

for aluminum.• WS401CCV & WS402CCV meets ANSI/BHMA 156.16 L12251 for brass and L32251

for aluminum.• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.

WS404CVXFeatures:• Constructed in cast brass.• Compact size.• Totally concealed mounting discourages vandalism or tampering.• Unit furnished with grey convex rubber bumper.• Packed with sheet metal screw, rawl plug and brad.• Finishes: US3, US4, US5, US10, US10B, US14, US15, US15A, US26, US26D, US28.

Base OverallProduct No. Diameter ProjectionWS404CVX 1" 17/32"

Mounting Base Base OverallProduct No. Hardware Diameter Thickness Projection

Wood screw,WS401CVX plastic anchor 2-1/2" 3/8" 1"

Wood screw,WS401CCV plastic anchor 2-1/2" 3/8" 1"

Screw, DrywallWS402CVX Anchor 2-1/2" 3/8" 1"

Screw, DrywallWS402CCV Anchor 2-1/2" 3/8" 1"

WS401CVX & WS402CVX

WS401CCV & WS402CCV

gerickso

Oval

Door Silencers

SR64Features:• For use on metal frames featuring

pneumatic design that, once installed,forms an air pocket to absorb shock and reduce noise of door closing.

• Tamper-proof once installed on the frame.• Proper installation also eliminates door

rattle and provides constant tension fordoor latches or locks.

• Packed in bags of 100. Grey also availablein bulk pack of 2500.

• Each bag has an installation tool included.• Meets ANSI/BHMA 156.16, L03011.• Finish: grey is standard. Black optional.

SR65Features:• For use on wood frames, also feature

pneumatic design to cushion shock andabsorb noise.

• To prevent removal, a small brad shouldbe driven into stop strip and throughstem of silencer, as shown in the detail.

• Packed in bags of 100.• Meets ANSI/BHMA 156.16, L03021• Finish: grey.

SR66Features:• Self Adhesive Rubber Silencers.• Economical installation requires no

drilling of frames.• Packed in sheets of 100.• Finishes: brown, grey, white.

Product No. Diameter ThicknessSR64 1/2" 1/8"

Product No. Height Width ThicknessSR64 3/4" 3/8" 1/8"

Product No. Diameter ThicknessSR66 1/2" 1/8"

D21

gerickso

Oval

B13USA 1.877.613.8766 Canada 1.905.403.1800 www.ives.ingersollrand.com

Protection Trim

B13

Pulls &

Plates

AH

inges & P

ivotsC

Flush Bolts & Coordinators

DLatches, Catches &

BoltsEStops

FExterior H

ardware

GM

iscellaneous Hardw

are

8400 Series Protection Plates • Door protection plates are available in .050” thick brass, stainless

steel or aluminum; and 1/8” thick high impact polyethylene in clear or black.

• Bevel edge options; specify B4E for all four edges.• Mounting screw pack furnished standard, 16 screws per pack.

Optional screw packs are available for TEK or TORK screw heads. Refer to the following chart for ordering.

• Specify NMH for no mounting holes.• Specify NMH-A for no mounting holes with adhesive.• Specify CS for counter sunk mounting holes.• Specify ERS prepped with extra row of screws.

Kickplate Gasket Tape Tape is recommended when using a brass plate on a metal door to reduce tarnishing from electrolytic oxidation. One tape pack will cover an the perimeters of a 8” x 34” kickplate. Order 8401 Gasket Tape.

8400 Protection Plate8402 (UL)* Protection Plate*UL mark appears in upper right corner.Number of screw packs required by plate size (specify TEK Screws or TORK screws).

22"-25" 26"-33" 34"-41" 42"-48"4"-8" 1 1 1 19"-16" 1 1 1 117"-24" 1 1 1 225"-32" 1 1 2 233"-40" 1 2 2 241"-48" 2 2 2 2

Finishes brassUS Number US3 US4 US10 US10B US15 US26 US26D

BHMA 605 606 612 613 619 625 626

Finishes stainless steelUS Number US32 US32D

BHMA 629 630

Finishes aluminumUS Number US28

BHMA 628

Finishes plasticClear and Black

Residential Grade Kickplates available Carded only, finishes PA28, PA3, PA619,

PA716, B3, B505, B619, B716

gerickso

Oval

B14USA 1.877.613.8766 Canada 1.905.403.1800 www.ives.ingersollrand.com

Protection Trim

B14

Pul

ls &

Pla

tes

AH

inge

s &

Piv

ots

CFl

ush

Bolts

& C

oord

inat

ors

DLa

tche

s, C

atch

es &

Bol

tsE Stop

sF

Exte

rior

Har

dwar

eG

Mis

cella

neou

s H

ardw

are

Mop Plates • Protect the bottom of the pull side of door subject to cleaning

and mopping procedures. • Size Ranges:4" to 6" high, 22" to 48" wide

Kick Plates • Protect the bottom of the push side of doors subject to

scuffing from foot traffic. • Recommended for all doors subject to normal use

(especially doors using a closer). • Size Ranges: 8" to 24" high, 22" to 48" wide

Stretcher Plates • Protect doors at specific areas where consistent contact is made by

stretchers, service carts or other equipment.• Usually applied to push side of doors. • Specify “B4E” Option for beveled edges.• Size Ranges: 6" to 8" high, 22" to 48" wide

Armor Plates • Protect lower half of doors from abuse by hard carts,

trucks and rough usage. • Usually applied to push side of single doors and both sides

of double acting doors. • Size Ranges: 26" to 48" high, 22" to 48" wide

gerickso

Oval

AR

CH

IT

EC

TU

RA

LH

IN

GE

S

5PB1 Steel with steel pin

5PB1 Brass with stainless steel pin

5PB1 Stainless steel with stainless steel pin (630 finish)

NRP = Non-Removable Pin

• Dimensions & tolerances conform to ANSI - A156.7• Packed with wood and machine screws• 5PB1 Steel description conforms to ANSI - A8133• 5PB1 Brass conforms to ANSI - A2133• 5PB1 Stainless Steel description conforms to ANSI - A5133

Size (Inches) Size (mm) Gauge

3.5 x 3.5 89 x 89 0.123

4.5 x 4 114 x 102 0.134

4.5 x 4.5 114 x 114 0.134

PLAIN BEARING • LOW FREQUENCY • STANDARD WEIGHT

For use on Standard Weight Doors with Low Frequency Usage, not intended for usewith door closing devices.

Full Mortise Hinges - 5 Knuckle

5PB15 Knuckle, Plain Bearing

5BB15 Knuckle, Ball Bearing

5BB1 Steel with steel pin

5BB1 Brass with stainless steel pin

5BB1 Stainless steel with stainless steel pin (630 finish only)


• Dimensions & tolerances conform to ANSI - A156.7• 5BB1 Steel description conforms to ANSI - A8112• 5BB1 Brass conforms to ANSI - A2112• 5BB1 Stainless description conforms to ANSI - A5112• Packed with wood and machine screws


4 x 4 102 x 102 0.130

4.5 x 4 114 x 102 0.134

4.5 x 4.5 114 x 114 0.134

4.5 x 5 114 x 127 0.146

5 x 4.5 127 x 114 0.146

2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT

For use on Standard Weight Doors with Medium Frequency Usage

5BB1RC5 Knuckle, Ball Bearing, Round Corner

5BB1 Steel with steel pin


• Dimensions & tolerances conform to ANSI - A156.7• 1/4" radius• 5BB1 Steel description conforms to ANSI - A8112• Packed with wood and machine screws


3.5 x 3.5 89 x 89 0.123

4.5 x 4 114 x 102 0.134

2 BALL BEARING • MEDIUM FREQUENCY • STANDARD WEIGHT

For use on Standard Weight Doors with Medium Frequency Usage

gerickso

Oval

gerickso

Oval

9

Full Mortise Hinges - 5 Knuckle

5BB1SC5 Knuckle, Ball Bearing,Swing Clear

5BB1SC Steel with steel pin

• Dimensions & tolerances conform to ANSI - A156.7• 5BB1SC Steel Description conforms to ANSI - A8122• Packed with flat head wood and machine screws


4.5 114 0.134

5 127 0.134

2 BALL BEARING • MEDIUM FREQUENCY

STANDARD WEIGHT • SWING CLEAR

Designed to completely clear the opening when door is opened 92 degrees.

Pins and tips are reversible.

AR

CH

IT

EC

TU

RA

LH

IN

GE

S

5BB1HW5 Knuckle, Ball Bearing,Heavy Weight

5BB1HW Steel with steel pin

5BB1HW Brass with stainless steel pin

5BB1HW Stainless steel with stainless steel pin (630 finish only)


• Dimensions & tolerances conform to ANSI - A156.7• 5BB1HW Steel description conforms to ANSI - A8111• 5BB1HW Brass description conforms to ANSI - A2111• 5BB1HW Stainless description conforms to ANSI - A5111• Packed with wood and machine screws


4.5 x 4 114 x 102 0.180

4.5 x 4.5 114 x 114 0.180

4.5 x 5 114 x 127 0.190

5 x 5 127 x 127 0.190

4 BALL BEARING • HIGH FREQUENCY • HEAVY WEIGHT

For use on Heavy Weight Doors or High Frequency Usage

5BB1HWRC5 Knuckle, Ball Bearing,Heavy Weight, Round Corner

5BB1HW Steel with steel pin

5BB1HW Brass with stainless steel pin

5BB1HW Stainless steel with stainless steel pin (630 finish only)


• Dimensions & tolerances conform to ANSI - A156.7• 1/4" radius• 5BB1HW Steel description conforms to ANSI - A8111• 5BB1HW Brass description conforms to ANSI - A2111• 5BB1HW Stainless description conforms to ANSI - A5111• Packed with wood and machine screws


4.5 x 4 114 x 102 0.180

4 BALL BEARING • HIGH FREQUENCY • HEAVY WEIGHT

For use on Heavy Weight Doors or High Frequency Usage

gerickso

Oval

gerickso

Oval

LCN CLOSERS121 W. RAILROAD AVE.P.O. BOX 100PRINCETON, IL, USA 61356-0100

PHONE 800-526-2400FAX 800-248-1460www.lcn.ingersollrand.com3/10

Standard 4010 series closer is shipped with regular arm, standard plastic c o v e r, and self reaming and tapping screws. See 4010 Series pages 5 & 6 for options.Size 6 (4010) cylinder for interior doors to 5’0” and exterior doors to 4’0”.Non-sized cylinder (4011) adjustable for interior doors to 4’6” and exteriordoors to 3’6”.Closer mounts hinge side, specify right or left swinging door.4011 cylinder meets ADA requirements. See 4010 Series page 7.Standard or optional custom powder coat finish.Optional plated finish on metal cover, arm and fasteners.Optional SRI primer for installations in corrosive conditions is available withpowder coat only.The 4010 Series is UL and cUL listed with regular or fusible link arms for self-closing doors.Tested and certified under ANSI Standard A156.4, grade one.

The 4010 SMOOTHEE® is LCN’s

best performing heavy duty

closer designed specifically for

institutional and other rugged

high traffic applications.

Ten Million Cycles

Cast Iron

Forged Steel Main Arm

Double Heat Treated Steel

Pinion

All Weather Fluid

LCN® Fast™ Power Adjust

Fast & Accurate Installation

UL & cUL Listed

LCN 4010 SERIES

Available Not available

3

HINGE (PULL) SIDE MOUNT

The 4011 includes theLCN® FAST™ Power Adjust,

a revolutionary visual indicatorfor Spring Power Adjustment.

Closer available with less than 5.0 lbs. opening force on 36" door.**Maximum opening/hold-open point with standard template.

*** Advanced Variable Backcheck

gerickso

Oval

gerickso

Oval

HINGE (PULL) SIDEMOUNTING

MAXIMUM OPENINGCan be templated for 100°,

A = 5 15/16” (151 mm)B = 11 15/16” (303 mm)

or 140°. A = 4 3/16” (106 mm)B = 10 3/16” (259 mm)

Hold-open points up to maximumopening with hold-open arm.

Arm Clearance above door. Regular arm requires C = 1 1/16” (27 mm).Hold-open arm requires C =1 3/8” (35 mm).Fusible link arm requires C = 1 5/8” (41 mm).

LCN 4010 SERIES

Butt Hinges should not exceed 5” (127 mm) in width.

Auxiliary Stop is recommended at hold-open point or where a door cannot swing 140°.

Reveal should not exceed 3/4” (19 mm). Fusible link arm should not exceed 1/8” (3 mm).

Top Rail less than 3 3/4” (95 mm) requires PLATE, 4010-18. Plate requires 2” (51 mm) minimum.

Clearance of 2 1/4” (57 mm) behind door required for 90° installation.

Delayed Action Add suffix “DEL” to selected cylinder.

Not available with 4016 cylinder.

Delays closing from maximum opening to approximately 70°.

Delay time adjustable up to approximately 1 minute.

OptionsSize 6 or non-sized cylinder.Delayed action cylinder.Hold-open or fusible link arm.Metal cover.

Special Templates Customized installation templatesor products may be available tosolve unusual applications.Contact LCN for assistance.

4LCN CLOSERS121 W. RAILROAD AVE.P.O. BOX 100PRINCETON, IL, USA 61356-0100




LCN 4010 SERIES CYLINDERSCYLINDER, 4010-3071

Standard, handed cast iron cylinder assembly.

For various applications see “Table of Sizes” on 4010 Series

page 7.

COVERSCOVER, 4010-72

Standard, non-handed plastic cover.

METAL COVER, 4010-72MC

Optional, handed cover. Required for plated finishes and

custom powder coat finishes.

ARMSREGULAR ARM, 4010-3077

Non-handed arm.

HOLD-OPEN ARM, 4010-3049

Optional, handed arm provides hold-open function,

adjustable at elbow.

FUSIBLE LINK ARM, 4010-3049FL

Optional, handed arm releases hold-open function when

exposed to temperatures above 165° F.

1/8” (3 mm) maximum reveal. NOTE: Check local codes

before specifing FL arms. NOT A LIFE SAFETY PRODUCT!

72

3077

72MC

3071

3049

3049FL

5

LCN 4010 SERIESINSTALLATION ACCESSORIESPLATE, 4010-18

Required where top rail is less than 3 3/4” (95 mm).

Plate requires minimum 2” (51 mm) top rail.

18



Indicates recommended range of door width for closer size.

HOW-TO-ORDER4010 SERIES CLOSERS1. SELECT CYLINDER SIZE

4011 (adjustable from size 1 to 5)4016 (DEL not available)

2. SPECIFY HANDRHLH

3. SELECT FINISHStandard Powder Coat __________Aluminum, Dark Bronze , Statuary,Light Bronze, Black, Brass.

Closer will be shipped with:- STANDARD COVER,- REGULAR ARM,- SELF-REAMING and TAPPING SCREWS,

unless options listed below are selected.

CLOSER OPTIONSCYLINDER

Delayed Action (DEL)COVER

Metal (MC)ARM

Hold-Open (H)Fusible Link, 165°F (FL)FINISHCustom Powder Coat (RAL) ___________(handed metal cover required)Plated Finish, US ___________ (handed metal cover required)SRI primer

SCREW PACKTB* & SRT Screw (TBSRT)Wood & Machine Screw (WMS)TB*, Wood & Machine Screw (TBWMS)TORX Machine Screw (TORX)TB* & TORX Machine Screw (TBTRX)* Specify door thickness if other than 1 3/4”.

INSTALLATION ACCESSORIESPlate, 4010-18

SPECIAL TEMPLATEST- _________

TABLE OF SIZES Select closer based on width of door.The spring power of non-sized 4011 cylinder is adjustable from size 1 throughsize 5 and is shipped set to size 3. Sized 4010 series cylinder available in size 6. Delayed action not available with 4016 cylinder.

size 3 size 4 size 5 size 6*4011

EXTERIOR (and VESTIBULE) DOOR WIDTH

24"610mm

30"762mm

36"914mm

42"1067mm

INTERIOR DOOR WIDTH

48"1219mm

24"610mm

34"864mm

38"965mm

48"1219mm

54"1372mm

60"1524mm

4016

size 2 size 3 size 4 size 5 size 6*4011

4016

* Adjustable Size 1 thru 5.

DOOR WIDTH 36" 42" 48"

8.5* lbs. 4011 4011 40115.0* lbs. 4011 4011 4011

REDUCED OPENING FORCE 4010 CLOSERSCAUTION ! Any manual door closer, including those certified by BHMA toconform to ANSI Standard A156.4, that is selected, installed and adjustedbased on ADA or other reduced opening force requirements may not providesufficient power to reliably close and latch a door.

Refer to POWER OPERATORS section for information on systems that meetreduced opening force requirements without effecting closing power.

* Maximum opening force

LCN 4010 SERIES

MinimumDoor

Width

MinimumDoor

Width

7



Standard 4110 series closer is shipped with EXTRA DUTY arm, standardplastic cover, 4110-201 FIFTH SCREW SPACER and self reaming andtapping screws. See 4110 Series pages 61 & 62 for options.Sized 6 cylinder adjustable for interior doors to 5’0” and exterior doors to 4’0”.Non-sized cylinder adjustable for interior doors to 4’6” and exterior doorsto 3’6”.Closer mounts parallel arm, specify right or left swinging door.4111 cylinder meets ADA requirements. See 4110 Series page 63.Standard or optional custom powder coat finish.Optional plated finish on metal cover, arm and fasteners.Optional SRI primer for installations in corrosive conditions is available withpowder coat only.The 4110 Series is UL and cUL listed for self-closing doors without hold-open.Tested and certified under ANSI Standard A156.4, grade one.

The 4110 SMOOTHEE® is LCN’s

best performing heavy duty closer

designed specifically for

institutional and other rugged

high traffic applications.

Ten Million Cycles

Cast Iron

Extra Duty Forged Steel Arm

Standard

Double Heat Treated Steel

Pinion

All Weather Fluid

LCN® Fast™ Power Adjust

Fast & Accurate Installation

UL & cUL Listed

LCN 4110 SERIES

Available Not available

Closer available with less than 5.0 lbs. opening force on 36" door.**Maximum opening/hold-open point with standard template.

*** Advanced Variable Backcheck

59

*PARALLEL ARM (PUSH SIDE) MOUNT

The 4111 includes theLCN® FAST™ Power Adjust,

a revolutionary visual indicatorfor Spring Power Adjustment.

*4110 HCUSH mount shown

gerickso

Oval

gerickso

Oval

PARALLEL ARM (PUSH SIDE)MOUNTING

MAXIMUM OPENINGEDA or Fusible Link arm can betemplated for100°,

A = 5 15/16” (151 mm) B = 7 1/4” (184 mm)

140°, A = 4 7/16” (113 mm) B = 5 3/4” (146 mm)

or 180°. A = 2 15/16” (75 mm) B = 4 1/4” (108 mm)

Hold-open points up to maximumopening with HEDA or Fusible Link arm.

CUSH arm can be templated formaximum opening at85°,

A = 8 5/16” (211 mm) B = 9 5/8” (244 mm)

90°, A = 7 11/16” (195 mm) B = 9” (229 mm)

100°, A = 6 7/16” (164 mm) B = 7 3/4” (197 mm)

or 110°. A = 5 9/16” (141 mm) B = 6 7/8” (175 mm)

Hold-open point at maximum openingwith HCUSH arm. Spring Cush hold-open points areapproximately 5˚ less than templatedstop point.

LCN 4110 SERIES

Butt Hinges should not exceed 5” (127 mm) in width.Auxiliary Stop is recommended at hold-open point, where a door cannot swing180°, or where CUSH-N-STOP arm is not used.Clearance for EDA, or CUSH shoe is 5 1/2” (140 mm) from door face.Top Rail less than 5 1/8” (130 mm) measured from stop requires PLATE, 4110-18.Plate requires 2” (51 mm) minimum measured from the stop.Stop Width minimum 1” (25 mm).Head Frame flush or rabetted requires CUSH FLUSH PANEL ADAPTER, 4110-419.Reveal less than 2 3/4” (70 mm), use CUSH SHOE SUPPORT, 4110-30 with CUSHarms.Blade Stop Spacer, 4110-61 required to clear 1/2” (13 mm) blade stop. Cush Arm requires CUSH SHOE SUPPORT, 4110-30 for fifth screw anchorage withCUSH arms.Delayed Action Add suffix “DEL” to selected cylinder (eg. 4111 DEL). Notavailable with 4116 cylinder. Delays closing from maximum opening toapproximately 70°. Delay time adjustable up to approximately 1 minute.Advanced Variable Backcheck cylinder starts backcheck at approximately 45°instead of the normal 75°. Add suffix “AVB” to selected cylinder.

OptionsSize 6 or non-sized cylinder.Delayed Action or AdvancedVariable Backcheck cylinder.HEDA, CUSH, HCUSH, SPRINGCUSH, SPRING HCUSH orFusible Link arm.Metal cover.

Special Templates Customized installation templatesor products may be available tosolve unusual applications.Contact LCN for assistance.



*

*5 11/16” (144 mm) For Fusible Link Arm applications

gerickso

Oval



LCN 4110 SERIES CYLINDERSCYLINDER, 4110-3071

Standard, handed cast iron cylinder assembly.

For various applications see “Table of Sizes” on 4110 Series

page 63.

COVERSCOVER, 4110-72Standard, non-handed plastic cover.

METAL COVER, 4110-72MCOptional, handed cover. Required for plated finishes andcustom powder coat finishes.

ARMSEXTRA DUTY ARM, 4110-3077EDA, 4110-3077EDAG,Non-handed parallel arm features forged, solid steel main andforearm for potentially abusive installations.Optional 4110-62G thick hub shoe for blade stop clearance.

HOLD-OPEN ARM 4110-3049EDAOptional handed arm provides hold-open function, adjustableat shoe.

FUSIBLE LINK ARM, 4110-3049FLOptional, handed arm releases hold-open function adjustableat shoe when exposed to temperatures above 165° F.NOTE: Check local codes before specifing FL arms. NOT A LIFESAFETY PRODUCT!

CUSH-N-STOP ARM, 4110-3077CNSOptional, non-handed parallel arm features solid forged steelmain arm and forearm with built-in stop in soffit shoe.

72

3077

72MC

3049

3077EDAG

61

3077CNS

3049FL 62FL

3071

H-CUSH ARM 4110-3049CNSOptional non-handed arm provides hold-open function withtemplated stop/hold-open points.Handle controls hold-open function.

SPRING CUSH ARM, 4110-3077SCNSOptional, non-handed parallel arm for abusive applicationsfeatures solid forged steel main arm and forearm with springloaded stop in the soffit shoe.

SPRING H-CUSH ARM, 4110-3049SCNSOptional, non-handed parallel arm for abusive applicationsfeatures solid forged steel main arm and forearm with springloaded stop in the soffit shoe. Handle controls hold-openfunction.

INSTALLATION ACCESSORIESPLATE, 4110-18Required for push side mount where top rail is less than 5 1/8”(130 mm), measured from the stop. Plate requires minimum 2” (51 mm) minimum top rail.Plate also used with CUSH Arm installations.

CUSH SHOE SUPPORT, 4110-30Provides anchorage for fifth screw used with CUSH arm,where reveal is less than 3 1/16” (78 mm).

BLADE STOP SPACER, 4110-61Lowers parallel arm shoe to clear 1/2” (13 mm) blade stop

PA FLUSH PANEL ADAPTER, 4110-419Provides horizontal mounting surface for EDA or CUSH shoe onsingle rabetted or flush frame.

18

30

419

LCN 4110 SERIES 3049CNS

62

3077SCNS

3049SCNS



61

gerickso

Oval

HOW-TO-ORDER4110 SERIES CLOSERS1. SELECT CYLINDER SIZE

4111 (adjustable from size 1 to 5)4116 (DEL, SHCUSH or HCUSH arm not available)

2. SPECIFY HANDRHLH

3. SELECT FINISHStandard Powder Coat __________Aluminum, Dark Bronze , Statuary,Light Bronze, Black, Brass.

Closer will be shipped with:- STANDARD COVER,- FIFTH SCREW SPACER- EDA ARM,- SELF-REAMING and TAPPING SCREWS,

unless options listed below are selected.

4110 CLOSER OPTIONSCYLINDER

Delayed Action ((DEL), not available with 4116)

Advanced Variable Backcheck (AVB)COVER

Metal (MC)FINISH

Custom Powder Coat (RAL) ___________(handed metal cover required)Plated Finish, US ______________ (handed metal cover required)SRI primer

SPECIFY ARMHold-Open Extra Duty (HEDA)Fusible Link,165° F (FL)Cush-N-Stop (CUSH)H-Cush-N-Stop (n/a with 4116 cylinder) (HCUSH)Spring Cush (SCUSH)Spring H-Cush (n/a with 4116 cylinder) (SHCUSH)Extra Duty (EDA)H-Extra Duty (HEDA)

SCREW PACKTB*, Self-Reaming & Tapping (TBSRT)Wood & Machine Screw (WMS)TB*, Wood & Machine Screw (TBWMS)TORX Machine Screw (TORX)TB* & TORX Machine Screw (TBTRX)

* Specify door thickness if other than 1 3/4”.INSTALLATION ACCESSORIES

Plate, 4110-18CUSH Shoe Support, 4110-30Blade Stop Spacer, 4110-61PA Flush Panel Adapter, 4110-419

SPECIAL TEMPLATEST- _________

LCN 4110 SERIES

Indicates recommended range of door width for closer size

TABLE OF SIZES Select closer based on width of door.The spring power of non-sized 4111 cylinder is adjustable from size 1 throughsize 5 and is shipped set to size 3.Sized 4110 series cylinder 6.Delayed action not available with 4116 cylinder.H - CUSH and SPRING H-CUSH arm not available with 4116 cylinder.

size 3 size 4 size 5 size 6*4111

EXTERIOR (and VESTIBULE) DOOR WIDTH

28"711mm

30"762mm

36"914mm

42"1067mm

INTERIOR DOOR WIDTH

48"1219mm

28"711mm

34"864mm

38"965mm

48"1219mm

54"1372mm

60"1524mm

4116

size 2 size 3 size 4 size 5 size 6*4111

4116

* Adjustable Size 1 thru 5

* Adjustable Size 1 thru 5

DOOR WIDTH 36" 42" 48"

8.5* lbs. 4111 4111 41115.0* lbs. 4111 4111 4111

REDUCED OPENING FORCE 4110 CLOSERSCAUTION ! Any manual door closer, including those certified by BHMA toconform to ANSI Standard A156.4, that is selected, installed and adjustedbased on ADA or other reduced opening force requirements may not providesufficient power to reliably close and latch a door.

Refer to POWER OPERATORS section for information on systems that meetreduced opening force requirements without effecting closing power.

* Maximum opening force

63

MinimumDoor

Width

MinimumDoor

Width

Toll Free Phone 1-800-647-7874Toll Free Fax 1-800-255-7874

E-mail: [email protected] www.ngpinc.com

Sadd

le Th

resh

olds

14

National Guard Products, Inc.PROTECTION, INSIDE OUT

Typical Wall .125

4"

1/2"

Typical Wall .250

3"

1/2

"

Typical Wall .125

4"

1/2"

5"

1/2"

Typical Wall .162

Typical Wall .175

6"

1/2"

Typical Wall .188

7"

1/2"

Thresholds are aluminum millfinishDKB indicates aluminum withdark bronze finish.

412 .625 lbs./ft.

412DKB .625 lbs./ft.

419 .72 lbs./ft.

419DKB .72 lbs./ft.

424 .72 lbs./ft.

424DKB .72 lbs./ft.

425 1.00 lbs./ft.

425DKB 1.00 lbs./ft.

426 1.35 lbs./ft.


427 1.58 lbs./ft.


Typical Wall .188

5"

5/8"

525 .93 lbs./ft.

525DKB .93 lbs./ft.

Typical Wall .188

4"

5/8"

524 .72 lbs./ft.

524DKB .72 lbs./ft.

All drawings are actual sizeexcept as noted.

All thresholds this page. 10C

1/2"

7"Typical Wall .250

8472 1.78 lbs./ft.

8472DKB 1.78 lbs./ft.

gerickso

Oval



Ther

mal B

arrie

r Thr

esho

lds

34


4"

1/2"

Typical Wall .110

8424 .75 lbs./ft.


5 "

1/2"Typical Wall .110

8425 .90 lbs./ft.


6"


8426 1.00 lbs./ft.

8426DKB 1.00 lbs./ft.

7 "


8427 1.20 lbs./ft.

8427DKB 1.20 lbs./ft.

8"


8428 1.30 lbs./ft.

8428DKB 1.30 lbs./ft.

9"


8429 1.60 lbs./ft.

8429DKB 1.60 lbs./ft.

10"


8430 1.70 lbs./ft.

8430DKB 1.70 lbs./ft.

1/2” added to thresholds under 61”1” added to thresholds over 61”

All thresholds this page.

gerickso

Oval

gerickso

Oval


E-mail: [email protected] www.ngpinc.com50


Available in 36”, 48”, 84”, 96” and 108” lengths.

7/16"

7/16"

Self Adhesive Seals

5020B Brown

5020C Charcoal

5020W White

Available in 17’, 20’, 21’, 25’ and 300’ rolls.

1/4"

3/8"

2525B Brown2525C Charcoal2525W White2525T Tan

1/2"

1/4"

5050B Brown5050C Charcoal5050W White5050T Tan5050CL Clear

HEAD &LATCH SIDE

DOORJAMB

HINGE SIDE

DOORJAMB

5021B Brown

5021C Charcoal

5021W White

11/32"

7/16"

7/16"

Available in 17’, 20’, 21’, 25’ and 300’ rolls.

DOOR DOOR

LATCH SIDE HINGE SIDE

Neoprene Gasketingwidth thickness

361 18’, 21’, 50’ rolls 3/8” x 3/16”362 18’, 50’ rolls 1/2” x 1/4”363 18’, 50’ rolls 3/8” x 1/8”

Self

Adhe

sive

Seals

Kerf Application

SiliconeSilicone

10C S

10C S

ESS **Edge Sealing System on 20 minrated wood doors up to 4’0 x 8’0 sin-gle, 8’0 x 8’0 std. pair with 9800 or9500 at meeting edge.

10C S

“FATT”

Fast Attach Two-Way Tape Fast attach two way tape provides an easy and effective alter-native to gasketing installation. A 1/2” wide 2-way tape isapplied to the metal housing insuring a quick and easy instal-lation. Then for security, 3 tek-type self drilling screws areused to further secure each piece of material to the framestop. A no problem installation with no holes to drill.

To order add suffix “FATT” to product number. See price listfor products available with this feature.

FATT IS NOT CLASSIFIED FOR USE ON FIRE DOORS.

1/2"

5/16"

5060B Brown5060CL Clear

Available in 7’, 8’, 9’,17’, and 21’ rolls

10C S

HEAD &LATCH SIDE

DOORJAMB

HINGE SIDE

DOORJAMB

(optional astragal application)

gerickso

Oval


E-mail: [email protected] ngpinc com

56


1 7/

16"

9/16

"C627AC627BC627DKB

7/8"

1/2"

600600A600B600DKB

7/8"

1"

601601A601B601DKB

5/8"

7/16

"

A605AA605BA605DKB

3/4"

1/2"

B606AB606BB606DKB

3/4"

9/16

"

C607AC607BC607DKB

1 1/

16"

1"

D608AD608BD608DKB

1 3/

16"

1 9/

16"

E609AE609BE609DKB

1 3/

8"1

3/4"

G610AG610BG610DKB

5 1/

2"1

3/4"

G611AG611DKB

2 1/

2"1

3/8"

H612AH612BH612DKB

2 1/

2"5

1/2"

H614AH614DKB

1 3/

8"4"

I-615AI-615BI-615DKB

5 1/

2"4"

I-616AI-616DKB

5/8"

1"

OV633AOV633BOV633DKB

5/8"

3/4"

OV634AOV634BOV634DKB

1/2"

7/8"

602A602DKB

1"

7/8"

603A603DKB

7/16

"

1/2"

.45O

A617A

10C 10C 10C

10C10C S

10C

S10C

10C

10C 10C

#6 x 3/4” Stainless Steel Sheet MetalScrews furnished.

S

10C

10C

S

10C

10C

10C

All Products this page.

Wild

Hair®

- Ny

lon B

rush

Sea

ls

gerickso

Oval

59

Allseal® Gasketing




Allseal® GasketingSpecially formulated to withstand greater temperature extremes while providing

maximum protection against air infiltration. Color of Allseal gasket material is Tan.

3/4" 7/16"

nylon +brush

9000A9000B9000DKB

1 1/4"

3/16"

silicone+

9001A9001B9001DKB

7/8"

5/16

"

1/4"

silicone+

1/4"

90029002A9002B9002DKB

nylon+

5/8"

7/16

"nylon+

5/8" 3/8"

silicone+9115A9115B9115DKB

7/8"

silicone+

3/8"

9125A9125B9125DKB

silicone+

1 1/2"

1/4"

1/4"

9700A9700B9700DKB

silicone+

1 1/2"

1/4"

1/4"

9700E9700EDKB

1 1/2"

7/16"

nylon +

1/4"

9706E9706EDKB

Perimeter Seals

Seals for Use with Parallel Arm Door Closers

Astragal Seals

1 5/16"

9004A9004B9004DKB

silicone+intumescent

nylon +

1/2"

nylon +

7/8"

96009600A9600B9600DKB

nylon+

7/8"

nylon +

1/2"

96009600A9600B9600DKB

nylon+

7/16"5/8"

9605A9605B9605DKB

9605A9605B9605DKB

Perimeter Seals or Sweeps

nylon +

10C S 10C S

10C S

10C

10C S

10C S

10C

10C 10C

10C S 10C

10C 10C S

#6 x 3/4” Stainless Steel Sheet Metal Screws furnished.

S

S

S

S S

S

gerickso

Oval




Swee

ps

7/8"

vinyl

7/8"

96V96VA96VB96VDKB

#6 x 3/4” stainless steelsheet metal screws furnished.

1"

vinyl

7/8"

97V97VA97VB97VDKB*

3/4"

vinyl

7/8"

98V98VA98VB98VDKB

1/2"

vinyl

7/8"

100V100VA100VB100VDKB**

1/2"

vinyl

1 1/

2"

101VA101VB101VDKB

3/4"

vinyl

1 1/

16"

102VA102VB102VDKB*

5/16"neoprene

15/1

6"

23/32"117N117NDKB

1 5/

8"

neoprene

7/8"

197NA197NB197NDKB

1"

neoprene

7/8"

198NA198NB198NDKB

1"

neoprene

1 1/

4"

199NA199NB199NDKB

3/8"

1 1/

4"

polyurethane

200UA200UB200UDKB

1/2"neoprene

1 1/

16"

201NA201NB201NDKB

5/8"

neoprene

1"

3/8"

202NA202NB202NDKB

2"

neoprene

1"

3/8"

203NA203NB203NDKB

3/4"

1 1/

4"

vinyl

1025VA1025VB1025VDKB*

3/8"neoprene

1 1/

4"

neoprene200NA 200NB200NDKB

silicone200SA200SB 200SDKB

7/8"

polyurethane

7/8"

198UA198UB198UDKB

All productsthis page:

OK for use on ‘S’ label doors.

10C

1"

black rubbercovered

fabric

1 1/

16"

2014A2014B2014DKB

vinyl is gray. Exceptions:*vinyl is black, ** vinyl is brown

neoprene, polyurethane are blacksilicone is gray

gerickso

Oval




Solid Metal Astragal Seals

Astra

gals

- Ove

rlapp

ing

Surfa

ce M

ount

ed

neoprene .094"

1 5/8"

3/8"

3/8"

3/16"

5/8"

neoprene

15/16"

1 5/8"

9/32"

silicone

109NA109NB109NDKB

114NA114NB114NDKB

178SA178SDKB

Maximum height 120”

A - clear B - gold

DKB - dark bronzevinyl is grayneoprene, silicone are black

Astragal/Meeting Stile Gasketing

#6 x 1 - #6 X 3/4” ” stainless steel SMSfurnished.

#6 X 3/4” ” stainlesssteel SMS furnished.

1/2"

1 1/8"

1 3/

16"

neoprene

148NA148NDKB

1 1/

16"

1 1/4"

3/16"

146NA neoprene146NB neoprene146NDKBneoprene

146SA silicone146SB silicone146SDKB silicone

146VA vinyl146VB vinyl146VDKB vinyl

#10 X 3/4” ” stainlesssteel SMS furnished.

1 3/8"

3/4"

1/4"

1/8"

158NA neoprene158NDKB neoprene

158PA pile158PDKB pile

158SA silicone158SDKB silicone

158VA vinyl158VDKB vinyl Maximum Height 120”

1 1/8"

7/8"

1/8"176A176DKB

Maximum height 120”

3/4"

1/4"

vinyl

1/8"

179VA179VDKB

1 5/8"

3/32"

*139SSStainless steel astragal type 304 finish 2B

2"

1/8"

*139A Aluminum clear anodized*139DKB Aluminum dark bronze *139BR Brass

2"

3/16"

3/16

"1 7/16"

jambdoor

15/16"1/8"

1392SP

Steel Security Astragal

*Available lead-linedsuffix - “LD”. Alsoavailable with SNB’s

10C

10C

Maximum height 120”#10-32 SNB’s furnished.

*139SP- Steel Prime Coat

#10 x 3/4” SMS furnished.

#10 x 3/4” SMS furnished.

silicone

114SA114SB114SDKB

Furnished with #12 x 1 1/4” SMS. Can replace required metal astragalon wood or metal doors. UL, Max gap between doors = 1/8”. Astragalmust overlap gap and inactive door min. of 3/4”.

gerickso

Oval

G 23

neoprene

1 1/2"

1/4

"

3/16"

pile

1 1/2"

1/4

"

7/16"

700NA700NB 700NDKB

silicone

1 1/2"

1/4

"

1/4"

polyurethane

1 1/2"

1/4

"

3/16"

vinyl

1 1/2"

1/4

"

3/16"

701PA701PB 701PDKB

703VA703VB 703VDKB

700SA700SB 700SDKB

700UA700UB 700UDKB

vinyl

1 1/2"

1/4

"

1/4"

vinyl

1 1/2"

1/4

"

3/16"

704VA704VB 704VDKB

705VA705VB 705VDKB

10C S10C

10C

10C10C

10C

S

silicone+

1 1/2"

1/4

"

1/4"

9700A9700B9700DKB

10C S

Profiles on this page may be cut to fit narrow frame stops for additional charge.Specify “cut to width” on order.

silicone

1 1/2"

1/4

"

7/16

"1 1/2" 1/4"

1/4"

vinyl

707SA707SB707SDKB

10C S

706A706B706DKB

10C S

siliconenylon brush

G A S K E T I N G

N AT I O N A L G U A R D P R O D U C T S , I N C .

Phone: 800-647-7874Fax: 800-255-7874

www.ngp.comP

erimeter S

eals for u

se with

Parallel A

rm C

losers

Perimeter Seals for use with Parallel Arm Closers

gerickso

Oval

Nothing is tougher.

At Schlage we know that every product you specify has to stand

up to constant use and abuse. Your building’s locking systems

face an additional challenge – keeping people and other assets

safe while delivering constant, reliable performance. Schlage

L-Series Extra Heavy Duty Mortise Locks are built to withstand

the rigors of daily use without fail.

L-SeriesCommercial Locks

We don’t compromise on security.

The safety and security of your clients’ buildings is something we

take very seriously. That’s why every Schlage lock and deadbolt

undergoes intensive testing to determine its ANSI grade level:

• Cycle tests • Resistance tests• Door impact tests • Warped door tests• Bolt strength tests

We pay attention to these details so you can focus on creating

a functional and aesthetically pleasing environment for your

clients. In fact, every one of our L-Series locks meets ANSI

Grade 1 standards for safety.

5

gerickso

Oval

605 Bright Brass

606 Satin Brass

609 Antique Brass

610 Bright Brass, Blackened

611 Bright Bronze

612 Satin Bronze

613 Oil Rubbed Bronze

616 Antique Bronze

619 Satin Nickel

625 Bright Chromium Plated

626 Satin Chromium Plated

629 Bright Stainless Steel

630 Satin Stainless Steel

Finish Key

3-5/8"92mm

4-5/8"117mm

2-3/4"73mm

13mm1/2"

4-5/8"117mm

06Material: Forged brass, bronze and cast stainless steel Finishes: 605, 606, 609, 610, 611, 612, 613, 616, 619, 625, 626, 629, 630

07 Material: Forged brass, bronze and cast stainless steel Finishes: 605, 606, 609, 610, 611, 612, 613, 616, 619, 625, 626, 629, 630

12Materials: Forged brass, bronze and cast stainless steel Finishes: 605, 606, 609, 610, 611, 612, 613, 616, 619, 625, 626, 629, 630 Specify door hand

9

3-5/8"92mm

4-5/8"117mm

gerickso

Oval

Escutcheons and RosesChoose from three types of escutcheon and two rose sizes to add tough,

durable performance to your lockset.

L Full FaceMaterial: Cold-forged brass, bronze or stainless steel Finishes: 605, 606, 612, 613, 619, 625, 626, 629, 630 Size: 8” x 1 ¾” x 7/16” (203 mm x 44 mm x 11mm)

L ConcealedMaterial: Cold-forged brass, bronze or stainless steelFinishes: 605, 606, 612, 613, 619, 625, 626, 629, 630Size: 8” x 1 ¾” x 7/16” (203 mm x 44 mm x 11 mm)

N EscutcheonMaterial: Heavy wrought reinforced brass, bronze or stainless steelFinishes: 605, 606, 612, 613, 619, 625, 626, 629, 630Size: 8” x 2 9/16” x 7/16” (203 mm x 65 mm x 11 mm)

Escutcheons

7/16"11mm

8"203mm

7/16"11mm

8"203mm

7/16"11mm

8"203mm

Roses

A Wrought Rose2 1/8” (54 mm) diameterAvailable for use on L-Series knob and lever designs. Order by letter designation corresponding to the design and diameter desired.

B Wrought Rose2 9/16” (65 mm) diameterAvailable for use on L-Series knob and lever designs. Order by letter designation corresponding to the design and diameter desired.

14

gerickso

Oval

Schlage ANSI

L9050 F04LV9050Office and Inner Entry LockLatchbolt retracted by knob/lever from either side unless outside is made inoperative by key outside or by turning inside thumbturn. When outside is locked, latchbolt is retracted by key outside or by knob/lever inside. Outside knob/lever remains locked until thumbturn is returned to vertical or unlocked by key. Auxiliary latch deadlocks latchbolt when door is closed. Inside liner is always free for immediate egress.

L9056LV9056L9050 with Automatic UnlockingLatchbolt retracted by knob/lever from either side unless outside is made inoperative by key outside or by rotating inside thumbturn. Outside knob/lever unlocked by key outside, thumbturn or closing door. Rotating inside knob/lever simultaneously retracts latchbolt and unlocks outside knob/lever. Auxiliary latch deadlocks latchbolt when door is closed. Inside lever is always free for immediate egress.

L9060 F09LV9060Apartment Entrance LockLatchbolt retracted by knob/lever from either side unless outside is locked by key from inside. When locked, latchbolt retracted by key outside or knob/lever inside. Auxiliary latch deadlocks latchbolt when door is closed. Inside lever is always free for immediate egress.

L9070 F05LV9070Classroom LockLatchbolt retracted by knob/lever from either side unless outside is locked by key. Unlocked from outside by key. Inside knob/lever always free for immediate exit. Auxiliary latch deadlocks latchbolt when door is closed. Inside lever is always free for immediate egress.

L9071LV9071Classroom Security LockLatchbolt retracted by knob/lever from either side unless outside is locked by key from either side. When locked, latchbolt retracted by key outside or knob/lever inside. Auxiliary latch deadlocks latchbolt when door is locked. Inside lever is always free for immediate egress.

Schlage ANSI

L9076 F06LV9076Classroom Holdback LockLatchbolt retracted by knob/lever from either side unless outside is locked by key. When locked, latchbolt retracted by key outside or knob/lever inside. Auxiliary latch deadlocks latchbolt when door is closed. Depress inside knob/lever and turn key 360º for holdback feature. Inside lever is always free for immediate egress.

L9077LV9077Classroom Security Holdback Lock Latchbolt retracted by knob/lever from either side unless outside is locked by key from either side. When locked, latchbolt retracted by key outside or knob/lever inside. Auxiliary latch deadlocks latchbolt when door is locked. Depress inside knob/lever and turn key 360º for holdback feature. Inside lever is always free for immediate egress.

L9080 F07LV9080Storeroom LockLatchbolt retracted by key outside or by knob/lever inside. Outside knob/lever is always inoperative. Auxiliary latch deadlocks latchbolt when door is closed. Inside lever is always free for immediate egress.

L9080ELLV9080ELElectrically Locked (Fail Safe)Outside knob/lever continuously locked by 24V AC or DC. Latchbolt retracted by key outside or by knob/lever inside. Switch or power failure allows outside knob/lever to retract latchbolt. Auxiliary latch deadlocks latchbolt when door is closed. Inside knob/lever always free for immediate exit. Inside lever is always free for immediate egress.

L9080EULV9080ELElectrically Unlocked (Fail Secure)Outside knob/lever unlocked by 24V AC or DC. Latchbolt retracted by key outside or knob/lever inside. Auxiliary latch deadlocks latchbolt when door is closed. Inside knob/lever always free for immediate exit. Inside lever is always free for immediate egress.

L9080EL-RXL9080EU-RXRequest to Exit (RX) Electrified LockSame as L9080EL and L9080EU functions. In addition, a micro-switch positioned inside the lock case monitors the retractor crank, and is actuated when rotation of the inside or outside knob/levers rotates the retractor hub. The switch signals the use of that opening to security systems, allowing a non-disruptive means of immediate egress. Specify per L283-059 for normally closed contacts (default). Specify L283-125 for normally open contacts. Inside lever is always free for immediate egress. (Previously XL11-807)

18

Lock Functions | Single Cylinder Non-Deadbolt Functions

gerickso

Oval

34

Door Preparation for L9000 Series

8"

203 mm

1-1/4"

32 mm

2-3/4"

70 mm

6-1/4 "

159 mm

4-1/2"

114 mm

1"

25 mm

3-7/8"

98 mm

5-9/16"

141 mm

1-1/4"

32 mm

2-3/4"

70 mm

3-3/4"

95 mm

4-1/2"

114 mm

1"

25 mm

Door Preparation for L400 Series

Specifications CertificationsANSI:L9000: ANSI A156.13 Series 1000, Grade 1 Operational and Security, UL Listed for 3-hour fire door (except L9076 and L9007). With inter-changeable core cylinders: Grade 2 Security.

With Concealed Shell Cylinder: A156.13 Grade 1 Operational and Security. ANSI/ASTM F476-76 Grade 40, UL Listed. L400: ANSI A156.5 Grade 1

California State Reference Code:(Formerly Title 19, California State Fire Marshal Standard) All levers with returns comply; levers return to within ½” of door face.

UL / cUL:All locks listed for A label single doors, 4’ by 10’. Letter F and UL symbol on latch front indicate listing. Electrified functions are UL19X Listed for single-point locking applications. UL437 Listed locking cylinder optional: specify Primus 20-500 Series cylinder.

Handing:L9000-Series lock bodies are field-reversible without disassembly.L400-Series locks are non-handed.

Door Thickness:13/4” (44 mm) standard. 13/8” (35 mm) to 21/2” (64 mm) optional. Over 21/2” (64 mm) door ranges vary by function. No escutcheon available for 13/4” (44 mm) doors standard. 2” to 23/8” (51 mm to 60 mm) optional. Specify door thickness if other than 13/4”.

Backset:2-3/4” (70 mm) only.

Armored Front:L9000-Series: 11/4” x 8” x 7/32” (32 mm x 203 mm x 6 mm) standard. 11/16” x 8” x 17/32” (27 mm x 203 mm x 6 mm) optional. L400-Series: 47/16” x 35/8” x 1” (113 mm x 92 mm x 25 mm)

Case Size:L9000-Series: 47/16” x 61/16” x 1” (113 mm x 154 mm x 25 mm)L400-Series: 47/16” x 35/8” x 1” (113 mm x 92 mm x 25 mm)

Spacing:Knob or lever to cylinder, 37/8” (98mm); knob or lever to thumbturn hub, 211/16” (68mm).

Bolts:1” (25mm) throw stainless steel deadbolt and 3/4” (19mm) throw stainless steel latch with anti-friction tongue.

Exposed Trim:Knobs: #41 and #42 heavy-duty wrought brass, bronze or stainless steel knobs match D-Series knobs.Levers: Forged brass or bronze and cast stainless steel. Designs available to match D-Series levers.93 Lever Design: Extruded brass, bronze or stainless steel.

Mediterranean Designs: Forged-brass lever and rose.

Escutcheons: L escutcheons are cold-forged brass or bronze and stainless steel. N escutcheons are heavy wrought reinforced brass, bronze and stainless steel.

Trim Combinations: Available with knob both sides, lever both sides, or knob and lever with rose or escutcheon both sides.

Strike: L9000-Series: ANSI curved lip strike 11/4” x 47/8” (32 mm x 124 mm) x 13/16” (30 mm) lip to center with dust box standard. L400-Series: 11/8” x 35/8” (29 mm x 92 mm) with dust box.

Cylinder & Keys: 6-pin Everest C123 keyway cylinder with two patented keys standard.

Keying Options:Interchangeable core and Primus high security cylinders. Master keying, grand master keying and construction keying.

gerickso

Oval

35

How to OrderTo order Schlage products, descriptive data should be in the same sequence as shown.

1 Line item number2 Quality3 Complete model number with function and cylinder typeTo order cylinder options, change “P” at the end of the model number as follows:

L9453P Standard

L9453L Less standard cylinder. For Primus cylinder, specify this option and order Primus cylinder separately.

L945C With temporary plastic construction cylinder. Double cylinder functions ordered less cylinder are furnished with these construction cylinders to maintain timing of key cams.

L9453J Prepared for full size interchangeable core, less core. For Primus core, specify this option and order Primus core separately.

L9453R With full-size conventional interchangeable core installed. Order control keys separately.

L9453T With full-size (temporary) construction core installed. Order all keys separately.

L9453BD Prepared for small format (Falcon, Best, etc.) interchangeable core (SFIC), less core.

L9453GD With Everest B Family restricted keyway small format core installed. Order control keys separately.

L9453HD With small format keyed brass construction core installed. Order all keys separately.

L9453BDC With small format disposable plastic construction core installed.

4/5 Outside design / finish. Specify tactile warning (knurling) here as “8” before lever design, e.g. 803. To specify complete design, combine the numeric knob or lever design with the alpha rose or escutcheon design. Example: 03L, 93A, 42B. When ordering Mediterranean design levers with L escutcheons, specify AST/00L, AVA/00L or MER/00L.

6/7 Inside design/finish. Leave blank if same as outside.

8 Hand. One hand per line item.

9 Front (use “Strike” field on Schlage form). Leave blank for standard armored front or enter number for narrow front.

10 Strike. Leave blank for standard or specify part number for optional strike. LLL = Less Strike.

11 Door thickness, if non-standard. Example: 200 = 2”.

12 Extension, to specify whether thick door is extended inside (EI), outside (EO), differently (ED) or equally (EE).

13 Dimension for strike lip lengths. See strike page for availability of specific dimensions with specific strikes.

14 Keying detail (e.g. key symbol, keyway, bitting) and other special requirements.

Line Item Qty Product

Outside InsideHand Front Strike Door

Thickness Ext Dim Additional DetailsDes Fin Des Fin

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Example

Line Item Qty Product

Outside InsideHand Front Strike Door

Thickness Ext Dim Additional DetailsDes Fin Des Fin

1 50 L9453P 03A 626 RH 10-091

2 50 L9453P 03A 626 LH 10-091

3 10 L9040 03A 626 RH 138

4 10 L9040 03A 626 625 LH 09-668 138

5 50 L9456P 07L 626 625 RH 09-668

6 50 L9456P 07L 626 LH

Note: Schlage order forms are available at no charge by contacting your IR Security & Safety Consultant or Customer Service.

Cylinder Only Cylinder with Compression Ring & Spring

Cylinder with Blocking Ring

Cylinder Only Cylinder with Compression Ring & Spring

Cylinder with Blocking Ring

100 = 1”

118 = 11/8”

114 = 11/4”

138 = 13/8”

112 = 11/2”

134 = 13/4”

200 = 2”

7

Real Security is Knowing Exactly What You Want and Getting It

The toughest cylindrical lock for heavy-duty commercial applications.

At Schlage we know that every product you specify has to stand up to constant

use and abuse without compromising security. The ND-Series gets the job

done with tough, dependable ANSI Grade 1 locks designed for use

in schools, hospitals, offices, retail spaces, and colleges and

universities. Built for heavy duty applications, ND-Series locks

are easy to service and maintain, are available with our

exclusive Vandlgard® technology, and offer a wide range

of styles and finishes to fit your project needs.

Pictured here: Sparta lever shownin 626 Satin Chrome

ND-Series

We don’t compromise on security.

The safety and security of your clients’ buildings is something we take very seriously.

That’s why every Schlage lock and deadbolt undergoes intensive testing to determine

its ANSI grade level:

• Cycle tests • Resistance tests• Door impact tests • Warped door tests• Bolt strength tests

We pay attention to these details so you can focus on creating a functional and

aesthetically pleasing environment for your clients. In fact, every one of our ND-Series

locks meets ANSI Grade 1 standards for safety.

7

gerickso

Oval

9

• Tested to at least four times the 800,000-cycle ANSI Grade 1 requirement

• Exceeds ANSI A156.2, Series 4000 Grade 1 locked lever torque requirements

• The only cylindrical lock available with our exclusive Vandlgard® technology

Locked lever freely rotates up and down while remaining securely locked. The Vandlgard function also increases resistance to over-rotation of the lever.

ND-Series with Vandlgard The ND-Series Vandlgard is ideal for areas subject to abuse or anywhere

vandalism is likely to be present, such as schools, universities, offices and

commercial/public buildings. Vandlgard prevents damage to internal lock

components caused by excessive force from hitting or standing on the lever to

gain access. Vandlgard functions maintain total key system and architectural

design compatibility with Schlage’s regular ND-Series cylindrical locks.

Built to perform without fail.

Outside lever

Rose

Cylinder

Outside spring cage assembly

Chassis adjusts 15/8” - 2 1/8” thick doors

Push-turn button (certain function) provides visible locking status

Latch 1/2” throw

Latch screws

Strike screws

Strike

Anti-rotation plate

Inside spring cage assembly with integrated spindle/spring cage

reduces lever wobble and droop

Spring cage screws

Rose

Inside lever

10

Lever Designs

Symbol: ATH (L-Series 07)

Material: Pressure cast zinc lever; wrought brass rose

Athens

All designs shown in 626 Satin Chrome

= Complies with ADA Accessibility Guidelines.

= FSIC - Full size interchangeable core option.

= Antimicrobial coating available on 626 finish only.

Symbol: SPA (L-Series 17)


Sparta

Symbol: RHO (L-Series 06)


Rhodes

= SFIC - Small format interchangeable core option.

Symbol: TLR (L-Series 03)


Tubular

Symbol: OME (L-Series Omega)


Omega

= Meets California code for 1/2” or less return to the door.

= Extended factory lead time.

Order as follows:8TR for Tubular

Order as follows:8AT for Athens8RO for Rhodes8SP for Sparta

Tactile Warning

Knurled

Milled

= Standard cylinder.

Only available on outside lever, unless otherwise specified

gerickso

Oval

11

Lever Finishes

605Bright Brass

606Satin Brass

612Satin Bronze

613Oil Rubbed

Bronze

619Satin Nickel

625Bright

Chromium Plated

626Satin

Chromium Plated

643eAged Bronze

ND SERIES LOCKS NEW IN 2009Athens • • • • • • • •Omega • • • • • • • •Rhodes • • • • • • • •Sparta • • • • • • • •Tubular • • • • • • • •

ADA-Compliant ProductsIn compliance with the American National Standards Institute (ANSI A117.1) and the Americans with Dis abil i ties Act

(ADA), Schlage Lock Company offers a wide selection of locks designed for the needs of the physically challenged.

This act is designed to provide protection for people with disabilities.

The intent of ADA is that owners of certain types of buildings must remove barriers and provide people with

disabilities with access equal to, or similar to, that available to the general public.

Product information and specifications contained in this catalog are subject to change without notice. Please consult the factory.

Door HandingAll ND levers are reversible. Hand information is

necessary to ensure proper cylinder orientation in keyed

functions, and finish of latchbolt and strike for locks that

are to be installed on reverse bevel doors. Follow the

diagram to correctly determine the hand of the door.

LHLeft Hand

INSIDE

OUTSIDE

OUTSIDE

INSIDE

LRLeft HandReverse

RHRight Hand

RR Right Hand

Reverse

e = an equivilent finish to the BHMA standard.

gerickso

Oval

12

Non-Keyed Locks

Lock Functions | ANSI A156.2 Series 4000 Grade 1

Passage Latch

• Both levers always unlocked.

ND10S F75

SCHLAGE ANSI

ND12D F89

SCHLAGE ANSI

Exit Lock

• Outside lever always fixed.• Inside lever always unlocked.

ND12DEL -

SCHLAGE ANSI

Electrically Locked (Fail Safe)

• Outside lever continuously locked electrically.

• Unlocked by switch or power failure.

• Auxiliary latch deadlocks latchbolt when door is closed.

• Inside lever always free for immediate exit.

ND12DEU -

SCHLAGE ANSI

Electrically Unlocked (Fail Secure)

• Outside lever continuously locked until unlocked by electric current.


• Inside lever is always free for immediate exit.

ND25D -

SCHLAGE ANSI

Exit Lock

• Blank plate outside.• Inside lever always unlocked.

Key Request to Exit Option

Electrified Push-button Springlatch Fixed lever

Deadlatch Blank plate Turn/push button

Outside Inside Outside Inside Outside Inside Outside Inside

Outside Inside

13

Keyed Locks

ND50PD F82

SCHLAGE ANSI

Entrance/Office Lock

• Push-button locking.• Push-button locks outside

lever until it is unlocked with key or by turning inside lever.

ND53PD F109

SCHLAGE ANSI

Entrance Lock

• Turn/push-button locking: Pushing and turning the button locks the outside lever, requiring use of a key until the button is manually unlocked.

• Push-button locking: Pushing button locks outside lever until unlocked by key or by turning the inside lever.

ND60PD F88

SCHLAGE ANSI

Vestibule Lock

• Latch retracted by key from outside when the outside lever is unlocked by key in inside lever.

• Inside lever is always unlocked.

ND66PD F91

SCHLAGE ANSI

Store Lock†

• Key in either lever locks or unlocks both levers.

ND40S F76

SCHLAGE ANSI

Bath/Bedroom Privacy Lock

• Push-button locking.• Can be opened from outside

with a small screwdriver.• Turn inside lever or close door

to release button.

ND44S - ND170

SCHLAGE ANSI

Single Dummy Trim

• Dummy trim for one side of door.

• Used for door pull or as matching inactive trim.

SCHLAGE ANSI

Hospital Privacy Lock

• Push-button locking.• Unlocked from outside by

turning emergency turn-button.

• Turn inside lever or close door to release button.

ND70PD F84

SCHLAGE ANSI

Classroom Lock

• Outside lever locked and unlocked by key.

• Inside lever always unlocked.

† Caution: Double cylinder locks are a life safety hazard in times of emergency and their use is not recommended. Installation should be in accordance with existing codes only.

Safe School Locks.

FSIC - full size interchangeable core option.

SFIC - small format interchangeable core option.

Standard cylinder.

Outside Inside Outside Inside Outside InsideOutside/Inside


gerickso

Oval

gerickso

Oval

14

Keyed Locks (continued)

Vandlgard Functions

Lock Functions | ANSI A156.2 Series 4000 Grade 1

ND80PD F86

SCHLAGE ANSI

Storeroom Lock

• Outside lever is fixed.• Entrance by key only.• Inside lever always unlocked.

ND82PD F87

SCHLAGE ANSI

Institution Lock†

• Both levers are fixed.• Entrance by key in either lever.

ND85PD -

SCHLAGE ANSI

Faculty Restroom Lock

• Outside lever is fixed.• Entrance by key only.• Push-button in inside lever

activates visual occupancy indicator, allowing only emergency master key to operate.

• Turn inside lever or close door to release visual occupancy indicator.

• Rotation of inside spinner-button provides lock-out feature by keeping indicator thrown.

ND80PDEU -

SCHLAGE ANSI

Electrically Unlocked (Fail Secure)

• Outside lever continuously locked until unlocked by key or electric current.



ND80PDEL -

SCHLAGE ANSI

Electrically Locked (Fail Safe)

• Outside lever continuously locked electrically.

• Unlocked by key outside or by switch or power failure.



ND91PD F82

SCHLAGE ANSI

Entrance/Office Lock

• Push-button locking.• Push-button disengages outside

lever until locked with key or by turning inside lever.

• Vandlgard is designed to disengage outside spindle from latch when locked.

ND73PD F90

SCHLAGE ANSI

Corridor Lock

• Locked or unlocked by key from outside.

• Push-button locking from inside.

• Turn inside lever or close door to release button.

• When outside lever is locked by key it can only be unlocked by key.


ND75PD -

SCHLAGE ANSI

Classroom Security Lock

• Key in either lever locks or unlocks outside lever.


Outside InsideOutside InsideOutside InsideOutside Inside


gerickso

Oval

22

SpecificationsHanding:

All ND-Series lever locksets are non-handed.

Door Thickness:

15/8” to 21/8” (41mm–54mm) standard including

Vandlgard® functions. 13/4” - 2” for function D85. See

accessories (Page 21) for spacers required for 13/8” doors.

Backset:

23/4” (70 mm) standard. 23/8”, 33/4” and 5”

(60 mm, 95 mm, 127 mm) optional.

Faceplate:

Brass, bronze or stainless steel. 11/8” x 21/4”

(29 mm x 57mm) square corner, beveled.

Lock Chassis:

Zinc plated for corrosion resistance.

Latch Bolt:

Steel, 1/2” (12mm) throw, deadlocking on keyed and

exterior functions. 3/4” (19 mm) throw anti-friction latch

available for pairs of fire doors.

Exposed Trim:

Levers: Pressure cast zinc, plated to match finish symbols.

Roses: Brass, bronze or zinc.

Strike:

ANSI curved lip strike 11/4” x 47/8” x 13/16”lip to center

standard. Optional strikes, lip lengths and ANSI strike box

available. See page 21.

Cylinder & Keys:

6-pin Everest C123 keyway standard with two patented

nickel silver keys per lock.

Keying Options:

Interchangeable core and Primus high security cylinders.

Master keying, grand master keying and construction keying.

Warranty:

Seven-year limited for all functions including Vandlgard.

CertificationsANSI:

Meets or exceeds A156.2 Series 4000, Grade 1 strength

and operational requirements. Meets A117.1

Accessibility Code.

Federal:

Meets FF-H-106C Series 161.

California State Reference Code:

(Formerly Title 19, California State Fire Marshal Standard)

All levers with less than 1/2” (64mm) returns comply;

Schlage levers return to within 1/2” of door face.

MEA Certification:

All electrified locking (fail-safe, unlocked by switch or

power failures) functions accepted for use in New York

City by the City of New York, Department of Buildings

(MEA 24-04-E).

All levers with less than 1/2” (64mm) returns comply with

California Fire Safety Codes.

Florida Building Commission:3/4” and 1/2” throw latch approved for Hurricane

Resistance with Miami-Dade County, Florida.

UL / cUL:

All locks listed for A label single doors, 4’ x 8’.

Letter F and UL symbol.

ADA Compliant:

Schlage Lock Company offers a wide selection of locks

designed to meet the Americans With Disabilities Act.

Door Preparation

2"57 mm

2"

54 mm

2"

70 mm

1" Dia.25 mm

1"29 mm

2"

70 mm

" Dia. (x 2)8 mm

gerickso

Oval

gerickso

Oval

10 © 2005 Ingersoll-Rand. May be copied for use with specification submittal.

338 385A

47 Top Latch

47 Bottom Latch

Top Strike

For use withwood frame

Bottom Strike

3347A/3547A Concealed Vertical Rod Device

3347A and 3547A for all types of single and double doors, UL listed for Panic Exit Hardware. Devices areANSI A156.3 – 2001 Grade 1. The 3547A has a smooth mechanism case and the 3347A has grooved case.The concealed vertical rod device is non-handed except when the SS (Signal Switch) option is used. Seeopposite page for available outside trim and device functions.

3347A/3547A fits door stiles as narrow as 1 ³|₄”(44 mm), wood door stiles as narrow as 4”(102mm). Newlydesigned device has a one piece center case cover.

The 3347A/3547A devices are available in the following finishes; US3, US4, US10, US26, US26D, US28,313AN and 315AN. See the inside cover for finish chips.

See page 31 for How to Order specification

Specifications

Device Lengths 3’ 2’4" to 3’ (711mm to 914 mm) Door Size4’ 2’10" to 4’ (864 mm to 1219 mm) Door Size

Strikes Top – 338 – Unfinished, Bottom – 385A – UnfinishedOptional Strikes – see page 20

Dogging Feature Hex key dogging standard

Dogging Options CD Cylinder Dogging see page 26LD Less Dogging see page 26

Electric Options LX Latchbolt Monitor Switch see page 22 RX Pushpad Monitor Switch see page 22 RX2 Double Pushpad Monitor Switch see page 22SS Signal Switch see page 23 EL Electric Latch Retraction see page 23 ALK Alarm Exit Kit see page 22

Miscellaneous Options PN Pneumatic Latch Retraction see page 26LBR Less Bottom Rod see page 27 GBK Glass Bead Kit see page 27PL Pullman Latch see page 27

Fasteners & Includes 1 ³|₄" (44mm) – 2 ¹|₄" (57mm) Wood & Metal DoorsSex Bolts (SNB) #425 SNB furnished standard for end case

#325 SNB furnished standard for EO (exit only device)

Latch Bolt Deadlocking Anti-friction Top & Bottom Bolt ⁵|₈" (16mm) throw

Device Centerline from 39 ⁵|₈" (1006mm) Standard, Adjustable from 35 5/8”(905mm) Finished Floor to 49 5/8”(1260mm)

Door Undercut ¹|₄" (7mm)

Center Case Dimensions 8 ³|₁₆" x 2 ¹³|₃₂" x 1 ⁹|₁₆" (208mm x 62mm x 40mm)

Mechanism Case Dimensions 2 ¹|₄" x 2 ¹|₄" (57mm x 57mm)

Vertical Rods Round 2 piece adjustable rods Top rod adjustable from 6’8”(2027mm) to 8’4”(2533mm)Bottom rod adjustable from 35 ⁵|₈”(905mm) to 49 ⁵|₈”(1260mm)Extension rod kits available for doors over 8’4” (2533mm)

Projection Pushbar Neutral – 3 ¹³|₁₆" (97 mm)Pushbar Depressed – 3 ¹|₁₆" (78 mm)

283

gerickso

Oval

20 © 2005 Ingersoll-Rand. May be copied for use with specification submittal.

Strikes for Rim Devices299 1408 1410 — Integral Stop

Projection ¹³|₁₆" (21mm) One per pair of doors Projection ¹|₂" (13mm)

1439 1606 1609

Projection ¹|₂" (13mm) Projection ³|₈" (10mm) For rim/vertical rod combination — consult factory

Strikes for Vertical Rod Devices260U — Flush Transom Only 266 299 299F

Projection ³|₈" (10mm) Projection 1¹|₄" (32mm) Projection ¹³|₁₆" (21mm) Projection ¹³|₁₆" (21mm)

304L 338 385A 499F

Mortise ¹³|₁₆" (21mm) Mortise ⁵|₈" (16mm) Mortise 2 ¹|₂" (64mm) Projection ¹⁵|₁₆" (21mm)

Strike Application/Minimum StileStandard OptionalSingle door Double door Single door Double doorStrike Stile Strike w/Mullion* Stile Strike Stile Strike w/Mullion* Stile

299 2 ³|₄" (70mm) 299 x 5654 2 ⁵|₈" (67mm)33A1439 1³|₄" (44mm) 1408 x 5754 1³|₄" (44mm) 1410 1 ³|₄" (44mm) 299 x 4954 3 ⁵|₁₆" (84mm)35A

1606 2 ¹|₂" (64mm) 1606 x 1654 2 ³|₄" (70mm)

3327A266 (Top) 266 (Top)

3527A 304L (Bottom) 1³|₄" (44mm) 304L (Bottom) 1³|₄" (44mm)248L-4 (Bottom) 248L-4 (Bottom)

3327A-F––––– –––––

299F (Top)––––– ––––– ––––– –––––3527A-F 304L (Bottom) 2 ³|₁₆" (56mm)

3327A-LBR-F ––––– –––––499F (Top) 3 ⁵|₈" (92mm)

––––– ––––– ––––– –––––(Req. Auxiliary Fire Latch)3347A 3547A 338 (Top) 2 ¹|₂" (64mm) 338 (Top) 1 ³|₄" (44mm) 304L (Bottom) 2 ¹|₂" (64mm) 304L (Bottom) 2 ¹|₂" (64mm)3348A 385A (Bottom) 385A (Bottom)3548A3347A-F3547A-F

—––– —–––338 (Top) 3 ¹|₂" (89mm) —––– —––– 304L (Bottom) 3 ¹|₂" (89mm)

3348A-F 385A (Bottom)3548A-F3347A-LBR 3547A-LBR 338 (Top) 2 ¹|₂" (64mm) 338 (Top) 2 ¹|₂" (64mm) —––– —––– —––– —–––3348A-LBR3548A-LBR3347A-LBR-F

—––– —––– 338 (Top) 3 ⁵|₈" (92mm) —––– —––– —––– —–––3547A-LBR-F*Mullion information — Refer to the General and Auxiliary Catalog.

DeviceType

3 ¹|₈" (79mm) 3 ¹|₈" (79mm)

2 ¹|₈" (54mm) 2 ¹|₈" (54mm)

299 (Top)385A (Bottom)

260U (Top)385A (Bottom)

299 (Top)385A (Bottom)

260U (Top)385A (Bottom)

33A/35A Strike/Stile Information

11

3347A/3547A Concealed Vertical Rod Device Trim

Exit only Dummy Trim Night Latch Night Latch ThumbturnPull when dogged Key retracts latchbolt Key retracts latchbolt Key locks & unlocks

Optional Pull Required

Product Description

Trim Description

Base Size

Grip Size

Projection

ANSI Function

Cylinder Type

Optional Trim(See page 19)

3347A-EO 3347A-DT 3347A-NL 3347A-NL-OP 3347A-TL3547A-EO 3547A-DT 3547A-NL 3547A-NL-OP 3547A-TL

–– 386DT 386NL 388 376T x 386

–– 7¹⁵|₃₂"h x 1⁵|₈"w 7¹⁵|₃₂"h x 1⁵|₈"w 7 ¹| ₂" h x 1¹¹|₁₆" w 7 ¹| ₂" h x 1¹¹|₁₆" w x ⁷| ₈" d

(190x41mm) (190x41mm) (190x43mm) (190x43x22mm)

––8¹|₂" h x 4⁵|₁₆"w 8¹|₂" h x 4⁵|₁₆"w

––8¹|₂" h x 4⁵|₁₆"w

(216x110mm) (216x110mm) (216x110mm)

–– 2⁷|₁₆" 2⁷|₁₆" 1" 1¹³|₁₆"(62mm) (62mm) (25mm) (46mm)

01 02 03 03 11-12

–– –– Rim Rim 1¹|₄" Mortise

x 360L-DT x550 DT–– x550 DT ––– x IVES 8190 10” x 392-6

x IVES 8190

Thumbturn-Blank Lever Lever-Blank Escutcheon Thumbturn Thumbturn-Blank EscutcheonEscutcheon Key Locks & Unlocks Always Operable Key Locks & Unlocks Always Operable

Always Operable (No Cylinder) (No Cylinder)(No Cylinder)

Product Description

Trim Description

Base Size

Grip Size

Projection

ANSI Function

Cylinder Type

Optional Trim(See page 19)

3347A-TL-BE 3347A-L 3347A-L-BE 3347A-T 3347A-T-BE3547A-TL-BE 3547A-L 3547A-L-BE 3547A-T 3547A-T-BE

376T-BE x 386 360L 360L-BE 360T 360T-BE

7¹|₂" h x 1¹¹|₁₆" w x ⁷|₈" d 7¹|₂" h x 1¹¹|₁₆" w x ⁷|₈" d 7¹|₂" h x 1¹¹|₁₆" w x ⁷|₈" d 7 ¹| ₂" h x 1¹¹|₁₆" w x ⁷| ₈" d 7 ¹| ₂" h x 1¹¹|₁₆" w x ⁷| ₈" d

(190x43x22mm) (190x43x22mm) (190x43x22mm) (190x43x22mm) (190x43x22mm)

8¹|₂" h x 4⁵|₁₆"w–– –– –– ––(216x110mm)

2 ⁷|₁₆" 3" 3" 1¹³|₁₆" 1¹³|₁₆"(62mm) (76mm) (76mm) (46mm) (46mm)

–– 08 or 09 Field Selectable –– 11 or 12 Field Selectable ––

–– 1¹|₄" Mortise –– 1¹|₄" Mortise ––

x 392-6 ––E360L-BE

––E360T-BE

See Page 18 See Page 18

Note: 360L & 360T used on Wood Door require the 33A-WDA cover plate376T used on Wood Door require #10-WDA cover plate.

For optional trims and functions see page 19

Field Selectable

gerickso

Oval

Date post:	30-Aug-2018
Category:	Documents
Upload:	lamque
View:	214 times
Download:	0 times

KOSTA’S BIG JOHN’S 776 SECTION 087100 PART 1 … · KOSTA’S BIG JOHN’S 776 SECTION 087100...

Documents