KS-143 represents the next generation of Heatset Kentucky Shine. It is formulated as an aqueous “Soft-Feel” overprint varnish for application to paper and paperboard through the inking unit of an offset press. Typical applications would be commercial and publication printing. Please refer to Kentucky Shine Press Instruction booklet for press preparation and use. For any additional information please contact your KUSTOM GROUP, LLC representative.
Performance Characteristics:
Excellent matte finish with velvet like feel
For best “Soft-Feel” effect, try applying a slightly heavier film. One way to achieve this is by disengaging one or more of the form rollers. This adjustment helps improve transfer and increase the KS-143 film thickness. If possible, use KS-143 in two separate printing units to improve the Soft-Feel as well
Care should be taken to adequately dry the thicker film. Please refer to drying requirements below
Good rub and scuff resistance (test versus specifications prior to use)
Drying Requirements: For best results, aqueous overprint varnishes require a sufficient volume of warm air
directed onto the varnished surface. However, the lowest possible web temperature is desired that will adequately dry the ink and overprint. This is best determined by experimentation using the actual substrate and inks. If the temperature is too high, the overprint varnish will dry and trapped ink oils may erupt through the varnish layer resulting in blisters or volcanoes.
For best results, disengage silicone applicator when running this product.
Application Weight: Apply about 20-25% more than oil-based overprints.
Ink Formulary: Limit wax to typical polyethylene to ensure proper inter-coat adhesion.
PTFE, micro crystalline wax or silicone may contribute to application problems.
Avoid the use of fugitive pigments that may bleed or change color when in contact with an alkaline product (alkali blue, rhodamine, red lake C, fluorescent, and many others). As a precaution, always evaluate new ink formulations/technologies with this aqueous/glycol overprint varnish.
FOR YOUR PROTECTION: The information and recommendation in the publication are the best of our knowledge, reliable. Suggestions made concerning uses or application are only the
opinion of KUSTOM SERVICES, LLC., and users should make their own test to determine the suitability of this product for their own particular purpose. However, because of numerous factors affecting results, KUSTOM SERVICES, LLC makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for a particular purpose, other than that the material conforms to its applicable current standard specification. Standard Specification, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/13/2013
Kustom Group LLC • 3 Carbon Way • Richwood KY 41094 • 859-485-8600 • www.kustomgroup.com
TECHNICAL DATA SHEET
KS-146 Kentucky Shine High Body Matte “Soft-Feel” OPV
Product Description:
KS-146 is formulated as a special effect tactile aqueous “Soft-Feel” application to paper and paperboard through the inking unit of a sheetfed offset press. Typical applications would be commercial printing. Please refer to the Kentucky Shine Press Instruction booklet for press preparation and use. For any additional information please contact your KUSTOM GROUP, LLC representative.
Performance Characteristics:
Excellent matte finish with velvet like feel.
Good rub and scuff resistance (test versus specifications prior to use).
Not recommended as a UV primer or for hot foil stamping, gluing, imprinting or film laminating.
The best Soft-Feel effect can be achieved by carefully applying a heavier film thickness but NOT via a double-bump application. Exercise care to ensure that the sheets are dry
KS-146 is recommended for single-sided application only (wet trap or off-line)
This product exhibits a characteristic cling in face-to-face conditions and may interfere with feeding, cutting, folding, etc.
We recommend using short lifts for jobs with heavy ink coverage
Ensure that the ink system is dry. Avoid using with extreme stay open inks
Drying Requirements: For best results, aqueous overprints varnishes require a sufficient volume of warm air directed onto the varnished surface. The use of IR units (short of medium wavelength) can provide drying assistance in many applications. Exercise care to avoid load temperatures in excess of 90° F.
Application Weight: Apply about 20 to 25% more than oil base overprints.
Ink Formulary: Limit wax to typical polyethylene to ensure proper inter-coat adhesion. The use of PTFE, microcrystalline wax or silicone may contribute to application problems. Avoid the use of pigments that may bleed or change color when in contact with an alkaline product (refer to the Kentucky Shine Press Instruction booklet). As a precaution, always evaluate new ink formulation and technologies with the aqueous overprint varnish.
FOR YOUR PROTECTION:
The information and recommendation in the publication are the best of our knowledge, reliable. Suggestions made concerning uses or application are only the opinion of KUSTOM SERVICES, LLC., and users should make their own test to determine the suitability of this product for their own particular purpose. However, because of numerous factors affecting results, KUSTOM SERVICES, LLC makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for a particular purpose, other than that the material conforms to its applicable current standard specification. Standard Specification, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/13/2013
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9805 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a “Soft-Feel” matte finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Soft-Feel exhibits an excellent matte appearance and non-burnishing characteristics.
A normal volume anilox roller should provide the desired film thickness for “Soft-Feel” properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9805 exhibits excellent rub and scuff resistance.
KS-9805 has been used successfully with litho oil-based, UV, UV Hybrid, web heatset and aqueous flexo in systems.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9805 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Double-bumping KS-9805 on a single-sided, or two-sided, application is NOT encouraged. This exaggerated film thickness is considered to be high risk for blocking, clinging, sticking, etc.
Ensure that the ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Physical Properties:
Viscosity: 16-18" #3 Zahn (Signature) @ 77° F
pH: 8.0 -8.5 @ 77° F
Solids: 32-36% Method 24
Shelf Life: One year (unopened container)
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness
for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9805 Aqueous “Soft-Feel” Matte Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9807 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a “Soft-Feel” matte finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Soft-Feel exhibits an excellent matte appearance and non-burnishing characteristics.
A normal volume anilox roller should provide the desired film thickness for “Soft-Feel” properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9807 exhibits excellent rub and scuff resistance.
KS-9807 has been used successfully with litho oil-based, UV, UV Hybrid, web heatset and aqueous flexo in systems.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9807 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure that the ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Physical Properties:
Viscosity: 20 - 22" #3 Zahn (Signature) @ 77° F
pH: 8.2 -8.7 @ 77° F
Solids: 32-36% Method 24
Shelf Life: One year (unopened container)
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current
Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/15/2013
TECHNICAL DATA SHEET
KS-9807 AQ Work & Turn “Soft-Feel” Matte Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9807HV is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a “Soft-Feel” matte finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Soft-Feel exhibits an excellent matte appearance and non-burnishing characteristics.
A normal volume anilox roller should provide the desired film thickness for “Soft-Feel” properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9807HV exhibits excellent rub and scuff resistance.
KS-9807HV has been used successfully with litho oil-based, UV, UV Hybrid, heatset and aqueous flexo ink systems. This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications.
KS-9807HV should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure the ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Physical Properties:
Viscosity: 28-30" #3 Zahn (Signature) @ 77° F
pH: 8.2 -8.7 @ 77° F
Solids: 32-36% Method 24
Shelf Life: One year (unopened container)
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/15/2013
TECHNICAL DATA SHEET
KS-9807HV High Viscosity AQ Work & Turn “Soft-Feel” Matte Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9811 is a modified version of KS-9807; a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems, for controlling foaming due to aggressive pumps and anilox systems. Typical applications include commercial, folding carton and specialty printing work where a “Soft-Feel” matte finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Soft-Feel exhibits an excellent matte appearance and non-burnishing characteristics.
A normal volume anilox roller should provide the desired film thickness for “Soft-Feel” properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9811 exhibits excellent rub and scuff resistance.
KS-9811 has been used successfully with litho oil-based, UV, UV Hybrid, web heatset and aqueous flexo ink systems.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9811 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure that the ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Physical Properties:
Viscosity: 20 - 22" #3 Zahn (Signature) @ 77° F
pH: 8.2 -8.7 @ 77° F
Solids: 32-36% Method 24
Shelf Life: One year (unopened container)
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9811 Low Foam “Soft-Feel” Aqueous Coating
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 02/15/2013
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-532 Matte UV Soft Feel Coating
Product Description KS-532 is a matte UV curable coating for application in-line over UV litho, UV flexo and aqueous flexo ink systems where a soft feel effect is desired. Typical applications include commercial sheetfed printing on paper or paperboard substrates. For additional information, contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Soft Touch Feel & Matte Gloss (12+ BCM Anilox with ¾+ inch lines to/from coating unit to achieve desired feel)
Low thixotropy
MAY BE crosslinked to improve chemical resistance1
MAY BE imprintable, foil-stampable, glueable, etc., but proper testing is recommended
Physical Properties Viscosity 30 - 35 sec. #3 Zahn
Specific Gravity 1.07
VOC <1%
End Use Considerations 1KS-532 does NOT contain a crosslinker which would limit its normal 6 month life. The addition of crosslinking materials can increase rub resistance but should be added press side. Since the use of crosslinker limits the pot life of the material to hours, it is NOT possible to return material for any reason once crosslinker is added and voids all warranties. Care should be used when using crosslinkers to limit the amount of wasted material. KS-532 should be evaluated under production conditions using actual ink system and substrate to ensure leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates and a primer may be considered.
Storage and Handling Information KS-532 is a unique UV curing product that is NOT generally compatible with epoxy acrylate based UV coatings. As a result, extra caution should be paid to flush and clean the coating unit before and after its use to make sure there is no cross contamination. Due to the unique nature of KS-532, not all normal UV press washes will clean it well. Kustom Group recommends its KS-718 for this purpose. If you choose a different wash up material, it should be checked to see how well it works with KS-532 before trying generally. Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, well-ventilated and dry area or uncontrollable polymerization of the product may occur. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Please refer to the Material Safety Data Sheet (MSDS) prior to handling for further details.
Kustom Group LLC • 3 Carbon Way • Richwood KY 41094 • 859-485-8600 • www.kustomgroup.com
TECHNICAL DATA SHEET
KS-148 Kentucky Shine Sandy Matte Heatset OPV
Product Description:
KS-148 is a tactile aqueous overprint varnish for application to paper and paperboard through
the inking unit of an offset press where a sandpaper feel is desired. Typical applications would be commercial printing. Please refer to the Kentucky Shine Press Instruction booklet for press preparation and use. For any additional information, please contact your KUSTOM GROUP, LLC representative.
Performance Characteristics:
Excellent matte finish with a gritty, sandpaper like feel.
For best textured effect, try applying a slightly heavier film. One way to achieve this is by disengaging one or more of the form rollers. This adjustment helps improve transfer and increase the film thickness. If possible, use KS-148 in two separate printing units to improve the
texture as well.
Care should be taken to adequately dry the thicker film. Please refer to drying requirements below.
Improved body to prevent dripping thru the ink fountain.
Good rub and scuff resistance (test versus specifications prior to use).
Physical Properties:
pH - 7.5 to 8.5 @ 77°
Specific Gravity – 0.929
Viscosity – 10 – 50 Poise
Application Information:
Drying Requirements: For best results, aqueous overprint varnishes require a sufficient volume of warm air directed onto the varnished surface. UThe lowest possible web temperature is desired that will adequately dry the ink and overprint. This is best determined by experimentation using the actual substrate and inks. If the temperature is too high, the overprint varnish will dry and trapped ink oils may erupt through the varnish layer resulting in blisters or volcanoes. U Application Weight: Apply about 20-25% more than typical oleoresinous formulation. Limit wax to typical polyethylene to ensure proper inter-coat adhesion. The use of microcrystalline wax or silicone may contribute to application problems. Avoid the use of pigments that may bleed or change color when in contact with an alkaline product (refer to the overview). As a precaution, always evaluate new ink formulations/technologies with this aqueous overprint varnish.
FOR YOU PROTECTION:
The information and recommendation in the publication are the best of our knowledge, reliable. Suggestions made concerning uses or application are only the opinion of KUSTOM SERVICES, LLC., and users should make their own test to determine the suitability of this product for their own particular purpose. However, because of numerous factors affecting results, KUSTOM SERVICES, LLC makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for a particular purpose, other than that the material conforms to its applicable current standard specification. Standard Specification, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9810 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a textured or sandpaper finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Textured or Sandpaper feel with excellent gloss
A normal volume anilox roller should provide the desired film thickness for textured properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9810 exhibits excellent rub and scuff resistance.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9810 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
*** KS-9810 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-9810 and recommends extensive testing and care be used when running KS-9810 to minimize these
conditions.
Physical Properties:
Viscosity: 20 - 24" #3 Zahn (Signature) @ 77° F
pH: 8.0 -8.5 @ 77° F
Solids: 44-48% Method 24
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/13/2013
TECHNICAL DATA SHEET
KS-9810 Textured Aqueous Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9803 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a textured or sandpaper finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Textured or Sandpaper feel with a satin appearance
A normal volume anilox roller should provide the desired film thickness for textured properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9803 exhibits excellent rub and scuff resistance.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9803 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
*** KS-9803 contains a dry material at a 30-40 micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-9803 and recommends extensive testing and care be used when running KS-9803 to minimize these
conditions.
Physical Properties:
Viscosity 18 - 20" #3 Zahn (Signature) @ 77° F
pH 8.0 -8.5 @ 77° F
Solids 40 - 50% Method 24
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness
for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9803 Satin Sandy Aqueous Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9815 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work where a textured or sandpaper finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Textured or Sandpaper feel with a matte appearance
A normal volume anilox roller should provide the desired film thickness for textured properties.
A chambered doctor blade anilox configuration will exhibit a smoother appearance versus a 2-roll coater.
KS-9815 exhibits excellent rub and scuff resistance. This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications.
KS-9815 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
*** KS-9815 contains a dry material at a 30-40 micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-9815 and recommends extensive testing and care be used when running KS-9815 to minimize these
conditions.
Physical Properties:
Viscosity: 22 - 24" #3 Zahn (Signature) @ 77° F
pH: 8.0 -8.5 @ 77° F
Solids: 40 - 50% Method 24
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/13/2013
TECHNICAL DATA SHEET
KS-9815 Sandy Matte Aqueous Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9820 is a special effect tactile aqueous coating for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with roll coater systems. Typical applications include commercial, folding carton and specialty printing work where a textured or sandpaper finish is desired. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Textured or Sandpaper feel with semi-satin gloss
KS-9820 exhibits excellent rub and scuff resistance
"MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9820 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
Recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
*** KS-9820 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-9820 and recommends extensive testing and care be used when running KS-9820 to minimize these
conditions.
Physical Properties:
Viscosity: 24 - 28" #3 Zahn (Signature) @ 77° F
pH: 8.0 - 8.5 @ 77° F
Solids: 34 - 38% Method 24
Pigment Selection: Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend avoiding the
use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only
the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of
publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED 03/25/2013
TECHNICAL DATA SHEET
KS-9820 High Viscosity Sandy Feel Semi-Satin AQ Coating
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 11/13/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-521 Sandy Gloss UV Coating
Product Description KS-521 is a gloss UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-521’s effect can be accentuated by increasing the amount of coating applied. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Textured or Sandpaper feel
Excellent cure response
Multiple application methods for desired effect
Not considered imprintable, foil-stampable, glueable, etc.
MUST BE MIXED PRIOR TO USING
Physical Properties Viscosity 22 – 26 sec. #3 Zahn
Specific Gravity 1.09
Solids > 99%
End Use Considerations *** KS-521 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anolox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-521 and recommends extensive testing and care be used when running KS-521 to minimize these conditions. KS-521 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
Technical Data Sheet
KS-600 Kustom Kure Satin Sandy UV Coating
Product Description KS-600 is a satin UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-600’s effect can be accentuated by increasing the amount of coating applied. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Textured or Sandpaper feel • Excellent cure response • Multiple application methods for desired effect • Not considered imprintable, foil-stampable, glueable, etc. • MUST BE MIXED PRIOR TO USING Physical Properties • Viscosity 22 – 26 sec. #3 Zahn • Specific Gravity 1.11 • Solids > 99% End Use Considerations *** KS-600 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anolox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-600 and recommends extensive testing and care be used when running KS-600 to minimize these conditions. KS-600 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 06/27/2011
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-600HV High Viscosity Satin Sandy UV Coating
Product Description KS-600HV is a satin UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-600HV’s effect can be accentuated by increasing the amount of coating applied. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Textured or Sandpaper feel • Excellent cure response • Optimized viscosity for roll coaters • Not considered imprintable, foil-stampable, glueable, etc. • MUST BE MIXED PRIOR TO USING Physical Properties • Viscosity 30 – 35 sec. #3 Zahn • Specific Gravity 1.11 • Solids > 99% End Use Considerations *** KS-600HV contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anolox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-600HV and recommends extensive testing and care be used when running KS-600HV to minimize these conditions. KS-600HV should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 05/23/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 11/14/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-411 Kustom Kure Sandy Matte UV Coating
Product Description KS-411 is a matte UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-411’s effect can be accentuated by increasing the amount of coating applied. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Textured or Sandpaper feel
Excellent cure response
Multiple application methods for desired effect
Not considered imprintable, foil-stampable, glueable, etc.
MUST BE MIXED PRIOR TO USING
Physical Properties Viscosity 30-35 sec. #3 Zahn
Specific Gravity 1.13
Solids > 99%
End Use Considerations *** KS-411 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anolox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-411 and recommends extensive testing and care be used when running KS-411 to minimize these conditions. KS-411 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 11/28/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-422 High Volume Sandy Feel Satin UV Coating
Product Description KS-422 is a satin UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-422 is specifically formulated for high volume applications. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Textured or Sandpaper feel
Excellent cure response
Multiple application methods for desired effect
Not considered imprintable, foil-stampable, glueable, etc.
MUST BE MIXED PRIOR TO USING
Physical Properties Viscosity 20 – 30 Poise (Cone and Plate)
Specific Gravity 1.11
Solids > 99%
End Use Considerations *** KS-422 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-422 and recommends extensive testing and care be used when running KS-422 to minimize these conditions. KS-422 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 01/08/2013
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-469 Sandy Matte UV Coating for Plastic
Product Description KS-469 is recommended for use as a UV coating where high performance, low gloss sandy feel and fast cure response are desired. Typical applications include selected plastic stocks. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Excellent sandy feel
Excellent cure response
Not considered imprintable, foil-stampable, glueable, etc.
Excellent adhesion to selected plastics
Physical Properties Solids > 99%
Specific Gravity 1.09
Viscosity 14 - 17 sec. #3 Zahn
End Use Considerations KS-469 should be evaluated under production conditions, using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Data Safety Sheet for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to this in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 01/08/2013
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-21006 Sandpaper Screen UV Coating
Product Description KS-21006 is a gloss UV coating that provides a sandpaper feel upon printing over multiple types of ink on paper or paperboard substrates. KS-21006’s effect can be accentuated by increasing the amount of coating applied. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Textured or Sandpaper feel with excellent gloss
Excellent cure response
Multiple application methods for desired effect
Not considered imprintable, foil-stampable, glueable, etc.
MUST BE MIXED PRIOR TO USE
Physical Properties Viscosity 40 - 45 sec. #3 Zahn
Specific Gravity 1.11
Solids > 99%
End Use Considerations *** KS-21006 contains a dry material at a small micron size that could cause increased wear of printing application materials; such as doctor blades, anilox rollers, pumps, etc., or cause other performance issues typically associated with coatings containing dry/abrasive types of material. For this reason, Kustom Group accepts no liability for the use of KS-21006 and recommends extensive testing and care be used when running KS-21006 to minimize these conditions. KS-21006 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 08/07/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-499 Vinyl Feel UV Coating
Product Description KS-499 is recommended for use as a UV curable tactile coating to be applied in-line over UV litho, UV flexo and aqueous flexo ink systems where a vinyl feel is desired. Typical applications include commercial sheetfed printing on paper or paperboard substrates where matte gloss is desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics
Vinyl Feel
Matte gloss
Low thixotropy
Excellent cure response
MAY BE imprintable, foil-stampable, glueable, etc., but proper testing is recommended
Physical Properties
Viscosity 30 - 35 sec. #3 Zahn
Specific Gravity 1.07
VOC <1%
End Use Considerations KS-499 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 04/26/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-605 Kustom Kure Textured UV Gloss Coating
Product Description KS-605 is formulated as a high viscosity UV coating that exhibits a rough, texture-like feel. KS-605 is for application over UV sheet-fed inks on paper or paperboard substrates. The effect may be improved with a higher volume anilox. KS-605 can also be applied through a silk screen. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Not considered imprintable, foil-stampable, glueable, etc.
Physical Properties Solids > 99%
Specific Gravity 1.13
Viscosity 20 – 30 Poise (TA Rheometer)
End Use Considerations KS-605 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Data Safety Sheet for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to this in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 02/06/2013
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-495 Water Droplet Raised UV Coating
Product Description KS-495 is formulated as a high viscosity UV coating for application over UV inks on paper or paperboard substrates. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Excellent gloss
Excellent cure response
Can be used to impart a raised, water droplet look to finished coating (The process requires a high volume anilox and an etched, raised photopolymer plate [usually proprietary].)
Can also be considered for other application methods (such as a gluer unit, roll coater, etc.) .
Not considered imprintable, foil-stampable, glueable, etc.
Physical Properties Solids > 99%
Specific Gravity 1.14
Viscosity 14 – 16 Poise (TA rheometer)
End Use Considerations KS-495 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Data Safety Sheet for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to this in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 11/16/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-508 Raised High Gloss UV Coating
Product Description KS-508 is formulated as a high viscosity UV coating for application over UV inks on paper or paperboard substrates. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Excellent gloss and lay
Excellent cure response
Can be used to impart a raised look to finished coating (The process requires a high volume anilox and an etched, raised photopolymer plate [usually proprietary].)
Can also be considered for other application methods (such as a gluer unit, roll coater, etc.) .
Not considered imprintable, foil-stampable, glueable, etc.
Physical Properties Solids > 99%
Specific Gravity 1.14
Viscosity 14 – 16 Poise (TA rheometer)
End Use Considerations KS-508 should be evaluated in the laboratory using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Data Safety Sheet for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to this in this Technical Data Sheet.
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
PRODUCT DESCRIPTION
KS-9076 is an acrylic-based aqueous coating containing silver pearl pigment for application to paper and paperboard with in-line coater/dampeners and blanket coaters. Typical applications include commercial or folding carton sheetfed work when one coating is desired for broad use in the pressroom.
PERFORMANCE CHARACTERISTICS
Exhibits excellent gloss and clarity.
Exhibits excellent rub and scuff resistance.
Exhibits typical luster characteristics associated with pearl pigments.
Suitable for work & turn and one-side printing.
"MAY BE SUITABLE" for some hot foil stamping, imprinting and gluing applications. Before doing so, KS-9076 should be completely evaluated under production conditions using the actual substrate and ink, as materials for foil stamping, imprinting and gluing vary from supplier-to-supplier. Feel free to contact Kustom Group for additional information.
PHYSICAL PROPERTIES
Viscosity: 18-22" #3 Zahn (Signature) @ 77° F
pH: 8.0-8.5 @ 77° F
Solids: 36-38% Method 24
Shelf Life: One year (unopened container)
Requires mixing prior to use as pearl pigments exhibit a tendency to settle
PIGMENT SELECTION
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments. Many pigments normally considered safe, may prove to be problematic in low color strength color matches. The safest option is to use inks formulated to resist the potential to burn. As a precaution, we strongly recommend that new pigments and ink formulations be evaluated with this coating.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for
their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the
MSDS for additional information. DATE REVISED 03/15/2013
TECHNICAL DATA SHEET
KS-9076 Kustom Kote Aqueous Pearl Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9808 is a special effect aqueous coating containing an effect pigment that provides a glitter effect for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Glitter appearance with excellent gloss
Anilox roller volume greater than 16 BCM should provide the desired film thickness for the glitter effect.
A higher viscosity version may be desired for blanket and roll coaters.
KS-9808 exhibits excellent rub and scuff resistance.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9808 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
Recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Extra care should be taken when cleaning to ensure all of the special pigment in the coating is removed to prevent contamination to other products.
Physical Properties:
Viscosity: 20 - 24" #3 Zahn (Signature) @ 77° F
pH: 8.0 -8.5 @ 77° F
Solids: 44-48% Method 24
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind,
expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9808 Glitter Kote AQ Coating
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
Product Description:
KS-9816 is a special effect aqueous coating with a sparkle effect for application to paper and paperboard with litho in-line coaters and flexo presses that are equipped with chambered doctor blade anilox systems. Typical applications include commercial, folding carton and specialty printing work. Contact Kustom Group for additional information, as it is important to fully understand the optimum conditions for success.
Performance Characteristics:
Sparkle appearance with excellent gloss
Anilox roller volume greater than 12 BCM should provide the desired film thickness for the sparkle effect.
A higher viscosity version may be desired for blanket and roll coaters.
KS-9816 exhibits excellent rub and scuff resistance.
This coating "MAY BE SUITABLE" for hot foil stamping, off-line UV coating, imprinting and gluing applications. KS-9816 should be completely evaluated under production conditions using the actual substrate, ink, and materials for foil stamping, off-line UV coating, imprinting and gluing to ensure satisfaction throughout the entire process.
Application Advisements:
Ensure ink system will dry/cure thoroughly. Avoid extreme stay open inks.
We recommend using short lifts for sheetfed litho jobs with heavy ink coverage.
Extra care should be taken when cleaning to ensure all of the special pigment in the coating is removed to prevent contamination to other products.
Physical Properties:
Viscosity: 20 - 24" #3 Zahn (Signature) @ 77° F
pH: 8.0 -8.5 @ 77° F
Solids: 44-48% Method 24
Pigment Selection:
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current
Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9816 Aqueous Sparkle Coating
Technical Data Sheet
KS-549 Kustom Kure Pearlescent Litho UV OPV Product Description KS-549 is formulated with pearlescent pigment to be used as a special effect press applied UV overprint varnish. KS-549 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrate. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Pearlescent Effect • Excellent litho properties • Not considered imprintable, foil-stampable, glueable, etc. Physical Properties • Viscosity 2500 – 3500 Poise (TA Rheometer) • Tack 3.0 – 5.0 @ 800 rpm/1 minute • Specific Gravity 1.22 • Solids > 99% End Use Considerations KS-549 contains pearlescent pigment that may settle. Care needs to be taken to ensure the pearl pigment stays in suspension by mixing thoroughly prior to use. KS-549 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV overprints may not exhibit complete intercoat adhesion over some substrates. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 07/07/2011
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-572 Silver Pearl Gloss UV Coating Product Description KS-572 is formulated with pearlescent pigment to be used as a special effect UV coating. KS-572 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Pearlescent Effect • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. Physical Properties • Viscosity 30 - 35 sec. #3 Zahn • Specific Gravity 1.12 • Solids > 99% End Use Considerations KS-572 contains pearlescent pigment that will settle. Care needs to be taken to ensure the pearl pigment stays in suspension by mixing thoroughly before and during press runs. KS-686 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 11/09/2011
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 09/07/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-686 Kustom Kure UV Silver Pearl Gloss Coating
Product Description KS-686 is formulated with pearlescent pigment to be used as a special effect UV coating. KS-686 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Pearlescent Effect
Excellent cure response
Not considered imprintable, foil-stampable, glueable, etc.
Physical Properties Viscosity 27 - 30 sec. #4 Zahn
Specific Gravity 1.17
Solids > 99%
End Use Considerations KS-686 contains pearlescent pigment that will settle. Care needs to be taken to ensure the pearl pigment stays in suspension by mixing thoroughly before and during press runs. KS-686 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 08/31/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-512 Glitter Gold UV Coating
Product Description KS-512 is formulated with a special effect pigments to create a brilliant gold glitter effect. KS-512 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
End Use Considerations KS-512 contains a pigment that may settle. Care needs to be taken to ensure the pigment stays in suspension by mixing thoroughly before and during press runs. KS-512 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
Technical Data Sheet
KS-615 Sparkle Gloss UV Coating Product Description KS-615 is formulated with a wide range micron special effect pigment to be used as a special effect UV coating. KS-615 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Sparkle or glitter effect; recommend >35 BCM anilox • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. Physical Properties • Dynamic Viscosity 10- 15 Poise • Specific Gravity 1.13 • Solids > 99% End Use Considerations KS-615 contains a pigment that will settle. Care needs to be taken to ensure the pigment stays in suspension by mixing thoroughly before and during press runs. KS-615 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 05/01/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-659 Glitter Kure UV Coating Product Description KS-659 is formulated with a special effect pigment to be used as a special effect UV coating. KS-659 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Excellent Glitter effect • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. • ** Recommended application is a 25 BCM anilox or higher and roll coater where heavy film
thicknesses may be applied Physical Properties • Dynamic Viscosity 10- 20 Poise • Specific Gravity 1.17 • Solids > 99% End Use Considerations KS-659 contains a pigment that may settle. Care needs to be taken to ensure the pigment stays in suspension by mixing thoroughly before and during press runs. KS-659 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 02/29/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-664 Sparkle Kure UV Coating Product Description KS-664 is formulated with a special effect pigment to be used as a special effect UV coating. KS-664 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Sparkle or glitter effect • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. Physical Properties • Dynamic Viscosity 10- 15 Poise • Specific Gravity 1.13 • Solids > 99% End Use Considerations KS-664 contains a pigment that will settle. Care needs to be taken to ensure the pigment stays in suspension by mixing thoroughly before and during press runs. KS-664 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 02/21/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-666 Combination Glitter Kure UV Coating Product Description KS-666 is formulated with two special effect pigments to be used as a special effect UV coating. KS-666 can be applied in-line over UV or hybrid UV ink, or offline over oil base sheetfed ink. Typical applications include commercial sheetfed printing on paper and paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Excellent Glitter effect • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. • ** Recommended application is a 25 BCM anilox or higher and roll coater where heavy film
thicknesses may be applied Physical Properties • Dynamic Viscosity 10- 20 Poise • Specific Gravity 1.17 • Solids > 99% End Use Considerations KS-666 contains a pigment that may settle. Care needs to be taken to ensure the pigment stays in suspension by mixing thoroughly before and during press runs. KS-666 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 03/15/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED: 06/29/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-21012 Kustom Kure - Sparkle Screen UV Coating
Product Description KS-21012 is formulated as a Sparkle Effect UV coating for use in the screen area. Typical applications include paper and paperboard substrates where a sparkle effect with very high gloss, good blocking and superior leveling are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Excellent gloss and clarity with a sparkle effect
Higher screen volumes will produce the best effect with a maximum of 305 mesh recommended
Excellent cure response
Not considered imprintable, foil-stampable, glueable, etc.
Physical Properties Viscosity 30 - 40 sec. #4 Zahn
Specific Gravity 1.11
Solids > 99%
End Use Considerations MIX WELL BEFORE USING as pigment in KS-21012 will settle. KS-21012 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
PRODUCT DESCRIPTION
KS-9000 is an acrylic-based aqueous coating for application to paper and paperboard with in-line coater/dampeners and blanket coaters. Typical applications include commercial or folding carton sheetfed work when one coating is desired for broad use in the pressroom.
PERFORMANCE CHARACTERISTICS
Exhibits excellent gloss and clarity.
Exhibits excellent rub and scuff resistance. This coating "MAY BE SUITABLE" for some hot foil stamping, Imprinting and gluing applications. Before doing so,
KS-9000 should be completely evaluated under production conditions using the actual substrate and ink, as materials for foil stamping, imprinting and gluing vary from supplier-to-supplier. Feel free to contact Kustom Group for additional information.
Suitable for work & turn and one-side printing.
PHYSICAL PROPERTIES
Viscosity: 18-20" #3 Zahn (Signature) @ 77° F
pH: 8.0-8.5 @ 77° F
Solids: 36-38% Method 24
Shelf Life: One year (unopened container)
PIGMENT SELECTION Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer
avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments. Many pigments normally considered safe, may prove to be problematic in low color strength color matches. The safest option is to use inks formulated to resist the potential to burn. As a precaution, we strongly recommend that new pigments and ink formulations be evaluated with this coating.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind,
expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information.
DATE REVISED 03/15/2013
TECHNICAL DATA SHEET
KS-9000 GENERAL PURPOSE AQUEOUS COATING
Technical Data Sheet
KB-3074 Strike-Thru Dull Sheetfed Overprint
Product Description KB-3074 is an alternative product to our KB-3026. KB-3074 dries slightly faster and has a reduced percentage of matting agent to widen the litho window on some presses. This Overprint is specially formulated to be used only during Strike-Thru Applications in which the Overprint is flood coated with KS-9000. Do not use this product as a stand alone Overprint. Performance Characteristics
• Excellent litho properties • Excellent Matte Contrast When Printed Over Heavy Ink Coverage • Best Results Obtained When Thicker Film is Applied • High Solids
Physical Properties Tack 8.0 - 9.0 @ 1200 rpm/1 minute Inkometer Stability 0.5 – 1.0 typical tack rise per min. for 5 mins. Solids 72 – 74% Special Instructions Due to the high percentage of matting agent and the low viscosity of this product the following precautions should be observed: 1. pH of fountain solution should be kept above 4.0 to prevent retardation of the drying. 2. Reduce water settings on press as much as possible. 3. Oxidative dry and the potential for piling is adversely affected if above instructions are not adhered to.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM GROUP, INC. , and users should made their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM GROUP INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 02/13/2013
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Kustom Group • 3 Carbon Way • Richwood, KY 41094 • 859·485·8600 • www.kustomgroup.com
PRODUCT DESCRIPTION
KS-9009 is an acrylic-based aqueous coating for application to metalized substrates with in-line coater/dampeners and blanket coaters. Typical applications include commercial or folding carton sheetfed work.
PERFORMANCE CHARACTERISTICS
Exhibits excellent gloss and clarity.
Exhibits excellent rub and scuff resistance.
Excellent adhesion to foil stocks.
Exhibits good low curl properties for low basis weight stocks
This coating "MAY BE SUITABLE" for some hot foil stamping, imprinting and gluing applications. Before doing so, KS-9009 should be completely evaluated under production conditions using the actual substrate and ink, as materials for foil stamping, imprinting and gluing vary from supplier-to-supplier. Feel free to contact Kustom Group for additional information.
PHYSICAL PROPERTIES
Viscosity: 17-20" #3 Zahn (Signature) @ 77° F
pH: 8.0-8.5 @ 77° F
Solids: 38-40% Method 24
Shelf Life: One year (unopened container)
PIGMENT SELECTION
Most aqueous coatings are alkaline in pH because of the presence of ammonia. We recommend that the printer avoid the use of inks containing pigments that may bleed or change color when being exposed to an aqueous coating. Pigments that typically exhibit this sensitivity to alkali include YS Rhodamine, BS Rhodamine, Methyl Violet, Fluorescent, Red Lake C, Alkali Blue (Reflex Blue) and possibly other pigments. Many pigments normally considered safe, may prove to be problematic in low color strength color matches. The safest option is to use inks formulated to resist the potential to burn. As a precaution, we strongly recommend that new pigments and ink formulations be evaluated with this coating.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or
applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for
their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the
MSDS for additional information. DATE REVISED 03/18/2013
TECHNICAL DATA SHEET
KS-9009 Gloss Aqueous Coating for Metallized Substrates
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 03/08/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-453 High Gloss UV Coating for Smooth Strike-Thru
Product Description KS-453 is the recommended UV coating for Smooth Strike Thru effect. Smooth Strike Thru is accomplished by flood coating KS-453 in-line wet trap over Kustom Sheetfed Strike Thru OPV (KB-3116). This system when applied correctly, will give a gloss/matte contrast in one pass through the press. This can be applied inline over UV or hybrid ink, or off line over dried oil-based ink. KS-453 is also recommended as a stand-alone imprintable UV gloss coating for adhesion to plastic. Typical applications include commercial sheetfed printing on paper or paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Recommended UV coating for smooth strike thru
Excellent gloss and clarity
Excellent cure response
Good adhesion to select plastic stocks
Foil-stampable and imprintable
Physical Properties Viscosity 10 - 12 sec. #3 Zahn
Specific Gravity 1.08
Solids > 99%
End Use Considerations KS-453 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
Technical Data Sheet
KB-3116 Sheetfed Smooth Strike-Thru Overprint for UV
Product Description KB-3116 offers enhanced litho and drying properties and is specially formulated to be used only for Strike-Thru applications. Strike-Thru is a visual effect that has wide appeal for many applications of paper and paperboard substrates. Strike-Thru is achieved by printing KB-3116 in the last printing unit and flood coating the entire sheet with KS-453 Kustom Kure - Strike-Thru UV Coating. The result is a very pronounced contrast between the matte and gloss portions of the sheet with a single pass through the press. KB-3116 IS NOT INTENDED TO BE USED AS A STAND-ALONE OVERPRINT VARNISH. Performance Characteristics
• Excellent litho properties • Excellent Matte Contrast When Printed Over Heavy Ink Coverage • Best Results Obtained When Thicker Film is Applied
Physical Properties Tack 6.0 – 10.0 @ 1200 rpm/1 minute Inkometer Stability 0.3 – 0.8 typical tack rise per min. for 5 mins. Solids 73 - 75% Special Instructions Due to the high percentage of matting agent and the low viscosity of this product the following precautions should be observed: 1. pH of fountain solution should be kept above 4.0 to prevent retardation of the drying. 2. Reduce water settings on press as much as possible. 3. Oxidative dry and the potential for piling is adversely affected if above instructions are not adhered to. FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM GROUP, INC. , and users should made their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM GROUP INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 04/18/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-688 Kustom Kure High Gloss UV Coating for Reticulation Strike-Thru Product Description KS-688 is recommended for use as a Strike Thru UV coating to be applied in-line over a sheetfed Strike Thru OPV (KB-3115) and UV or hybrid UV ink systems. Typical applications include commercial sheetfed printing on paper or paperboard substrates where excellent gloss and minimal gloss-back are desired. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Excellent gloss and clarity • Excellent cure response • Not considered imprintable, foil-stampable, glueable, etc. Physical Properties • Viscosity 26 – 29 sec. #3 Zahn • Specific Gravity 1.11 • Solids > 99% End Use Considerations KS-688 should be evaluated in the laboratory using the actual Strike-Thru sheetfed OPV (KB-3115), ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some ink systems. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 09/19/2011
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet KB-3115 Sheetfed Reticulation Strike-Thru Overprint for UV
Product Description KB-3115 offers enhanced litho properties and is specially formulated to be used only for Strike-Thru applications. Strike-Thru is a visual effect that has wide appeal for many applications of paper and paperboard substrates. Strike-Thru is achieved by printing KB-3115 in the last printing unit and flood coating the entire sheet with KS-688 Kustom Kure - Strike-Thru UV Coating. The result is a very pronounced crawling effect of KS-688 over KB-3115 with a single pass through the press. KB-3115 IS NOT INTENDED TO BE USED AS A STAND-ALONE OVERPRINT VARNISH. Performance Characteristics
• Excellent reticulation effect when KS-688 is flood coated over it • Best effect is achieved when thicker film of KB-3115 is applied • Exhibits enhanced litho properties • UV coating applied on KB-3189 will not pass tape or scratch test
Physical Properties Tack 5.0 - 9.0 @ 1200 rpm/1 minute Inkometer Stability 0.3 – 0.8 typical tack rise per min. for 5 mins. Solids 79 – 81% Special Instructions Due to the high percentage of matting agent and the low viscosity of this product the following precautions should be observed: 1. pH of fountain solution should be kept above 4.0 to prevent retardation of the drying. 2. Reduce water settings on press as much as possible. 3. Oxidative dry and the potential for piling is adversely affected if above instructions are not adhered to.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM GROUP, INC. , and users should made their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM GROUP INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 08/14/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM GROUP, INC. , and users should made their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM GROUP INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 06/15/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-463 UV Matte Litho OPV for UV Strike-Thru
Product Description KS-463 UV OPV is formulated to be used under UV coatings with the potential to create various Strike-Thru effects in a full UV system. For example, if you wet trap our KS-688 UV Coating inline over KS-463 UV OPV you can create a large, water droplet Strike-Thru effect. A more subtle Strike-Thru effect can be achieved by wet trapping our KS-460 UV Coating over KS-463 UV OPV. Both combinations produce a very pronounced contrast between the UV OPV and UV coating portions of the sheet with a single pass through the press. Strike-Thru is a visual effect that has wide appeal for many applications of paper and paperboard substrates. Best results are achieved when the UV coating is wet trapped over an uncured UV OPV.
1. Reduce water settings on press as much as possible. 2. Wash up with standard UV wash.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 12/12/2012
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
Technical Data Sheet
KS-460 Kustom Kure High Gloss Foil-Stampable UV Coating
Product Description KS-460 is formulated as a high gloss foil-stampable UV coating for on-line application over UV or hybrid UV inks or off-line application over dried oil-based inks. KS-460 is also recommended as the UV coating for our full UV strike thru system over the top of KS-463 UV S.T. Matte OPV. (See Full UV Strike Thru System Technical Bulletin for more information) Typical applications include paper and paperboard substrates when one coating is desired for broad use in the pressroom. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative.
Performance Characteristics Excellent gloss and clarity
Produces a very smooth finish when applied by a roller or flexo coating unit
Recommended coating for Full UV Strike Thru System used over KS-463 UV S.T. Matte OPV
Physical Properties Solids > 99%
Specific Gravity 1.07
Viscosity 18 – 22 sec. #3 Zahn
End Use Considerations KS-460 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV coatings may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved.
Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Data Safety Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
Technical Data Sheet
KS-599 Reticulation Strike Thru Gloss Litho UV OPV Product Description KS-599 is recommended for use as a UV overprint varnish for spot application allowing a UV coating to reticulate when printed overtop. This reticulation area would stand out against the normal overall lay of the flood coating. Typical applications include sheet-fed offset printing where the OPV is applied in-line over UV or hybrid UV litho ink on paper, folding carton and select plastic stocks. For additional information regarding assistance and applications, please contact your KUSTOM SERVICES, INC. representative. Performance Characteristics • Excellent cure response • Excellent litho properties • Adhesion to select plastic stocks • Considered imprintable, foil-stampable, glueable, etc. Physical Properties • Viscosity 125 – 175 Poise (TA Rheometer) • Tack 1.5 – 3.5 @ 400 rpm/1 minute • Specific Gravity 1.14 • Solids > 99% End Use Considerations KS-599 should be evaluated under production conditions using the actual ink system and substrate to ensure that leveling, intercoat adhesion, gloss and other performance characteristics are acceptable. In general, UV overprint varnishes may not exhibit complete intercoat adhesion over some substrates. A primer may be considered for use if this property needs to be improved. Storage and Handling Information Care should be taken not to expose radiation curable products to temperatures exceeding 100°F for prolonged periods of time or to direct sunlight. Storage must be in a cool, shaded, well-ventilated and dry area. To do otherwise might cause uncontrollable polymerization of the product with generation of heat. Do not store this material under an oxygen-free atmosphere. This material should not be stored for more than six (6) months. Certain precautions should be taken when handling this product. Please refer to the Material Safety Data Sheet (MSDS) for further details. This product contains materials that may cause moderate skin injury (reddening and swelling) and/or sensitization. Since irritation may not occur immediately, contact can go unnoticed. Consult the MSDS for appropriate equipment prior to using this or any other materials referred to in this Technical Data Sheet.
FOR YOUR PROTECTION: The information and recommendations in this publication are, to the best of our knowledge, reliable. Suggestions made concerning uses or applications are only the opinion of KUSTOM SERVICES, INC., and users should make their own tests to determine the suitability of this product for their own particular purposes. However, because of numerous factors affecting results, KUSTOM SERVICES, INC. makes no warranty of any kind, expressed or implied, including those of merchantability and fitness for particular purpose, other than that the material conforms to its applicable current Standard Specifications. Standard Specifications, although current at the time of publication, are subject to change without notice. Please refer to the MSDS for additional information. DATE REVISED: 10/04/2011
Kustom Group ● 3 Carbon Way ● Richwood, KY 41094 ● www.kustomgroup.com
