KWIK-SMART - Binder Group · Lighter modulisation Reduce weight in buildings with no loss of...

KWIK-SMART METAL FRAMING| PIPE SUPPORTS| TEST PLUGS| HARDWARE

| CABLE MANAGEMENT

BUILDING SERVICES SOLUTIONS

CAT

ALOGUE

Head Office:Binder Group PTY LTD (Western Australia)26 Miles RoadKewdale WA 6105Phone: +61 (0) 8 9353 2208Fax: +61 (0) 8 9353 2751Email: [email protected]

Binder Group PTY LTD (Victoria) 12 Wedgewood RdHallam VIC 3803Phone: +61 (0) 3 9702 4360Fax: +61 (0) 3 9796 5049Email: [email protected]

Binder Group PTY LTD (Queensland)2/11-13 Allan StreetLoganholme QLD 4129Phone: +61 (0) 7 3421 0222Fax: +61 (0) 7 3421 0299Email: [email protected]

A K E E S A F E T Y P R O D U C T

Binder Group’s building services range of products tailored for the HVAC&R industry. Binder Group is a privately owned company and has been in Australia for over 30 years and is a market leading manufactur-er / supplier of pipe and structural supports for the industrial resource sector, specialising in delivering quality locally designed solutions.

Binder Group brings you a Commercial Building Services range of Kwiksmart products designed to support every application for HVAC&R, Mechanical Services, Electrical, Refrigeration and Plumbing installers. Our leading Flagship product Ultrastrut Channel and Ultrastrut Canti-levers are revolutionising the way support infrastructure is designed and installed on commercial projects and day to day installations. To compliment Ultrastrut we are offering the ability to turnkey a project from specification through to expedition by working with distribution partners, contractors and consultants across all disciplines.

Binder Group’s unique value add proposition offers unrivalled, drafting, engineering and design support from consultant through to installer ensuring that our clients not only get a product but a “solution”

All Binder products can be sourced through Electrical, HVAC&R, Plumb-ing, and Fastener distributors.

To know more about where you can source Kwiksmart contact your local Binder office located in Victoria, QLD and Western Australia with offices opening in other states soon.

KWIKSMART and ULTRASTRUT YOUR SMARTER BUILDING SERVICES SOLUTION

Kwik-Smart 5

“Z” Shape FittingsFlat Plate Fittings

PE- Blocks

Punched Angles

US Trapeze Kit

Electrical FittingsBeamClamps

Reducers

Angle Fittings

Cantilever Brackets

Clips & Clamps

Post Base Fittings

Pipe Support

Concrete Inserts

Cable Ladder

Flat CrossFlat Bends

Test Plug BeamClamp®

Channel Closures

Binder Tray

TEE

Risers

Channel Nuts

Channels

Visual CONTENT

P8 - P15

P23 - P24

P26 - P28

P31 - P33

P34 - P43 P45- P47 P49- P52 P53- P54 P55- P73

P16 P17 P21 P22

P22

P25 P25

P23 P24

P29 P30

P30 P30 P30 P30

P24

Using the UltraSTEEL™ state-of-the-art metal forming technology we have improved the performance of 2.5mm standard compliant strut profiles.

The patented UltraSTEEL™ process improves the load bearing capacity of steel against a similar gauged metal, so we can make it both stronger and lighter.

The UltraSTEEL™ process improves

strenght.

BRITISH STANDARD COMPLIANT STRUT PROFILE LOWER PRICE

An UltraSTEEL™ product

It may look different, because of the UltraSTEEL™process, but UltraSTRUT™ is a direct replacementfor all BS compliant 41x41 and 41x21 strut channelsections in 2.5mm and fits all existing ancillarycomponents. We provide plain, slotted and B-to-Bconfigurations in pre-galvanised, post-galvanised,hot-rolled and stainless steel material, so there’s astrut for all your applications. All this means, thatwhen selecting UltraSTRUT™ you get to benefitfrom the cost savings without having to worry aboutperformance.

• BS 6946 : 1988 compliant• Fits all existing ancillary components• All standard materials and finishes available

A DIRECT REPLACEMENT INEVERY WAY

ENHANCE YOUR GREENCREDENTIALS

Easier to work with

UltraSTRUT™ uses less steel for any given length, which means less material is used. It also means lower transport related pollution and cost, with more lengths being carried on each load.

Being lighter, UltraSTRUT™ is easier to handle, lift and transport, so it helps reduce installation cost.

Lighter modulisationReduce weight in buildings with no loss of integrity

CHANNELS -

8

All Channels come in 6.0 meter lengths

Other finishes available upon request.

Key to finishesGB= Galvanised BondHDG =Hot Dip Galvanised

SS=Stainless Steel

UltraSTRUT™

UNIFORMLY DISTRIBUTED LOAD CENTRALLY CONCENTRATED LOAD

SpanColumnEffectiveLength(mm)

Stress Limited Load &

deflection

Deflection Limited Load

(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 822 1.62 795 441 411 1.29 411 2761000 411 6.47 199 110 206 5.18 124 691500 274 14.56 88 49 137 11.65 55 312000 206 25.88 50 28 103 20.70 31 172500 164 40.44 32 18 82 32.35 20 113000 137 58.23 22 12 69 46.59 14 8

Plain 41X 41 mmUS 1000 [GB/ HDG]

US 1000 T [GB/ HDG] Slotted 41X 41 mm




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 884 1.47 884 522 441 1.18 442 3261000 442 5.88 235 130 221 4.71 147 821500 295 13.24 104 58 147 10.59 65 362000 221 23.53 59 33 110 18.82 37 202500 177 36.77 38 21 88 29.41 23 133000 147 52.94 26 14 74 42.35 16 9

CHANNELS

Kwik-Smart 9

When ordering, please quote Part Number for required size and surface finish.

Plain 41X 41 mm Size 2.5mm

Slotted 41X 41 mm

KS 1000 [GB/ HDG]

KS 1000 T [GB/ HDG]




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 954 1.02 954 954 477 0.82 477 4771000 477 4.09 477 323 239 3.28 239 2021500 318 9.21 259 144 159 7.38 159 902000 239 16.37 145 81 119 13.12 91 512500 191 25.58 93 52 95 20.50 58 323000 159 36.84 65 36 80 29.52 40 22




Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 887 1.12 887 887 443 0.90 443 4431000 443 4.50 443 273 222 3.60 222 1711500 296 10.12 213 121 148 8.11 137 762000 222 18.00 123 68 111 14.42 77 432500 177 28.12 79 44 89 22.53 49 273000 148 40.49 55 30 74 32.44 34 19

Size 2.5mm

CHANNELS -

10




SS=Stainless Steel

UltraSTRUT™

Plain 41X 21 mmUS 3300 [GB/ HDG]

Slotted 41X 21 mmUS 3300T [GB/ HDG]




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 293 2.78 165 91 147 2.23 103 571000 147 11.14 41 23 73 8.91 26 141500 98 25.06 18 10 49 20.04 11 62000 73 44.45 10 6 37 35.63 6 42500 59 69.60 7 4 29 55.68 4 23000 49 100.22 5 3 24 80.18 3 2




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 267 3.10 134 75 133 2.48 84 471000 133 12.41 34 19 67 9.93 21 121500 89 27.92 15 8 44 22.34 9 52000 67 49.63 8 5 33 39.71 5 32500 53 77.55 5 3 27 62.04 3 23000 44 111.68 4 2 22 89.34 2 1

CHANNELS

Kwik-Smart 11


Plain 41X 21 mmKS 3300 [GB/ HDG]




Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 330 2.14 330 214 165 1.71 165 134 1000 165 8.56 96 53 83 6.86 60 33 21500 110 19.26 43 24 55 15.43 27 15 2000 83 34.24 24 13 41 27.43 15 8 2500 66 53.50 15 9 33 42.87 10 5 3000 55 77.03 11 6 28 61.73 7 4

Slotted 41X 21 mmKS 3300T [GB/ HDG]




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 308 2.42 308 177 154 1.94 154 1101000 154 9.69 79 44 77 7.76 50 281500 103 21.80 35 20 51 17.47 22 122000 77 38.76 20 11 39 31.06 12 72500 62 60.56 13 7 31 48.53 8 43000 51 87.21 9 5 26 69.88 6 3

Size 2.5mm

Size 2.5mm

CHANNELS -

12




SS=Stainless Steel

UltraSTRUT™

Back to Back 41X 82 mmUS 1001 [GB/ HDG]




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 2463 0.82 2463 2463 1231 0.66 1231 12311000 1231 3.30 1167 648 616 2.64 616 4051500 821 7.42 519 288 410 5.94 324 1802000 616 13.20 292 162 308 10.56 182 1012500 493 20.62 187 104 246 16.49 117 653000 410 29.69 130 72 205 23.75 81 45

Back to Back 41X 21 mmUS 3301 [GB/ HDG]




deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 267 3.10 134 75 133 2.48 84 471000 133 12.41 34 19 67 9.93 21 121500 89 27.92 15 8 44 22.34 9 52000 67 49.63 8 5 33 39.71 5 32500 53 77.55 5 3 27 62.04 3 23000 44 111.68 4 2 22 89.34 2 1

CHANNELS

Kwik-Smart 13





Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 2766 0.59 2766 2766 1383 0.47 1383 13831000 1383 2.35 1383 1383 691 1.88 691 6911500 922 5.29 922 725 461 4.24 461 4532000 691 940 691 408 346 7.54 346 2552500 553 14.69 470 261 277 11.77 277 1633000 461 21.16 326 181 230 16.95 204 113

Back to Back 41X 82 mmKS 1001 [GB/ HDG]




Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 975 1.33 975 975 488 1.07 488 4881000 488 5.34 456 253 244 4.28 244 1581500 325 12.01 203 113 163 9.63 127 702000 244 21.36 114 63 122 17.11 71 402500 195 33.37 73 41 98 26.74 46 253000 163 48.06 51 28 81 38.51 32 18

Back to Back 41X 21 mmKS 3301 [GB/ HDG]

Size 2.5mm

Size 2.5mm

CHANNELS

14




SS=Stainless Steel




Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 574 0.96 1486 826 287 0.77 929 5161000 287 3.86 372 206 143 3.09 232 1291500 191 8.68 165 92 96 6.95 103 572000 143 15.42 93 52 72 12.36 58 322500 115 24.10 59 33 57 19.31 37 213000 96 34.70 41 23 48 27.81 26 14

Plain 41X 41 mm

Slotted 41X 41 mm

KS 2000 [GB/ HDG]

KS 2000T [GB/ HDG]


SpanColumnEffec-tiveLength(mm)


Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 538 0.90 1268 704 269 0.85 792 4401000 269 3.61 317 176 134 3.39 198 1101500 179 8.13 141 78 90 7.64 88 492000 134 14.45 79 44 67 13.58 50 282500 108 22.59 51 28 54 21.21 32 183000 90 32.52 35 20 45 30.55 22 12

Size 1.6mm

Size 1.6mm

CHANNELS

Kwik-Smart 15





Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 170 2.21 193 107 85 1.77 120 671000 85 8.83 48 27 43 7.08 30 171500 57 19.87 21 12 28 15.92 13 72000 43 35.32 12 7 21 28.30 8 42500 34 55.19 8 4 17 44.22 5 33000 28 79.47 5 3 14 63.68 3 2

Plain 41X 21 mm

Slotted 41X 21 mm

KS 4000 [GB/ HDG]

KS4000T [GB/ HDG]




Deflection


(Kg)


Deflection


(Kg)Load(Kg)

Deflection(mm)

Span/200

Span/360

Load(Kg)

Deflection(mm)

Span/200

Span/360

500 159 2.06 157 87 79 2.02 98 551000 79 8.23 39 22 40 8.08 25 141500 53 18.52 17 10 26 18.17 11 62000 40 32.92 10 5 20 32.30 6 32500 32 51.45 6 3 16 50.48 4 23000 26 74.08 4 2 13 72.69 3 2

Size 1.6mm

Size 1.6mm

CHANNELS

16

ReferenceAxis X-X Axis Y-Y

Ixx cm4 Zxx cm3 Rxx cm Iyy cm3 Zyy cm3

Ryy cm Area cm2

KS3300 1.20 1.06 0.73 5.73 2.60 1.55 2.23KS3301 5.68 3.13 1.13 10.74 5.20 1.55 4.46KS3300T 0.99 0.73 5.31 2.57 1.68 1.88 7

CHANNEL AXIS DATA

CHANNEL CLOSURES



Ryy cm Area cm2

KS1000 7.25 3.25 1.49 9.25 4.48 1.69 325KS1001 36.59 9.42 2.37 18.50 8.96 1.69 6.50KS1000T 6.13 3.02 1.45 9.19 4.45 1.78 2.90



Ryy cm Area cm2

KS4000 0.60 0.59 0.67 2.95 1.50 1.49 1.33KS4000T 0.49 0.55 0.66 2.92 1.48 1.62 1.12



Ryy cm Area cm2

KS2000 4.63 2.07 1.50 6.08 2.94 1.72 2.06KS2000T 3.95 1.94 1.46 3.95 2.93 1.81 1.85

KS 1000 / 1001 / 1000T

KS 3300 / 3301 / 3300T

KS 2000 / 2000T

KS 4000 / 4000T

KS2240 KS4240 KS1184

Plain 62 X 41 mmKS 5500 [GB/ HDG]

UNIFORMLY DISTRIBUTED LOAD COLUMN LOADING DATASpanColumnEffec-tiveLength(mm)

Max. allowance


Max. allowance

Load(KN)

Deflection(mm)

Span/200

Lateral Load

600 22.9 1.0 22.9 24.91000 13.7 2.0 13.7 18.11500 9.2 5.0 9.2 12.32000 6.9 8.0 6.9 9.32500 5.5 13.0 5.5 7.73000 4.6 18.0 3.8 -

Size 2.5mm




SS=Stainless Steel

Kwik-Smart 17

KS1000 KS3300

Point Load (250 mm centres)

750 Kgs

550 Kgs

Continuous Load(per 1000mm)

2200 Kgs

3000 Kgs

Concrete Strength 32MN/M2

CONCRETE INSERTS (Manufactured to Order)

Concrete Inserts are available in standard lengths of 3 and 6 metres which are supplied com-plete with polystyrene infill and End Caps in place. Non-standard lengths can be supplied in increments of 200mm. For shorter lengths, please consult our technical/sales department.

Concrete Inserts are manufactured from standard channel sections KS1000 and KS3300. The inclusion of Concrete Inserts into walls, floors, ceilings and ducts etc. at the initial stages of construction provides a flush surface for fixing and supporting electrical and mechanical services.

Material :BS 1449 HR4 PO Z25 EN10147:1992FE250 - G275 PGRolling Tolerance to BS 2994

Strength :32N/M2 Finished : HDG = BS 729

Recommended LoadingsResults prepared from tests carried out by the department of Civil Engineering at the University of Birmingham

END CAP. If site installation requires concrete insert to be cut, end caps MUST be re-inserted at each end.

41 x 41 x 2.5g Weight:- 2.64 Kg/M

Nail to shutteringbefore pouring

Removepolystyrene

Insert channel nut and secure bracket

41 x 21 x 2.5g Weight:- 1.84 Kg/M

Drawings not to scaleAll dimensions in mm

18

CHANNEL technical DATA

The following materials are used In the manufacture of Hi-Strut channels: 1. Pre-Galvanised (PG) BSEN 10147: 1992, S280 GD + Z275.2. Hot Rolled Pickled & Oiled (HRPO) BS 1449: 1991.3. Post Galvanised (HDG) BS 1449: 1991, BS 729.4. Stainless Steel (SS) BSEN 10088-2: 1995, 316L X2CrNiMo17-12-2.

1. All loads are calculated in accordance with BS5950:Part 5: 1998 Code of Practice, for the design of cold formed sections.

2. The minimum yield stress of pre-galvanised steel used in the manufacturer of Hi-STRUT channels is Ys = 250 N/mm2.

3. Beam loads and corresponding deflections are calculated using a yield of 250 N/mm2. These values are calculated in accordance with section 3.4 of BS5950:Part 5.

4. All beam loads and deflections stated do not apply to material that has been post galvan-ised i.e. (heat treatment has been applied af-ter forming). If beam loads and deflections are required for post galvanised products please contact, the manufacturer.

5. A global safety factor of 1.6 was used to determine safe working loads from limited state analysis.

6. Column loads are calculated in accordance with section six BS5950:Part 5. Effective col-umn lengths to be determined by the designer in accordance with Table 9 BS5950:Part 5.

7. Column loads have been calculated so that the maximum slenderness ratio Le/r does not exceed 180°.

8. Beams are assumed to be simply support-ed and provide adequate lateral restraint over the given span.

9. Beam loads are applied through the shear of the section in the direction indicated in the tables.

10. Alternative beam safe load tables are pro-vided for a uniformly distributed load or con-centrated near the centre of the span. (See Figure 1.).

11. Example of how to evaluate the ultimate load on an intermediate span. Extract from the S100 Load Table not shown in tables.

Channel Load Table Assumptions:

Material and Finish Standards:

CalculationSpan (mm)(a) 500(e) 825 = New Intermediate Span(b) 1000

Load (Kg)(c) 954 for 500 span(d) 477 for 1000 span

Find the ultimate load at a span of 825mm, using the following formula.

New Ultimate Load = New Ultimate Load =

= 643.95kg

Channel Load Table

{[ {[(954-477) (825-500)(1000-500) X954 -{[ {[(c-d)

(c-a)(b-a) XC -

Kwik-Smart 19

Ultrastrut CHANNEL PRODUCT TESTINGTest ObjectiveTo determine the ultimate load capacity of the UltraStrut product to BS6946:1988 using both pull out and slip criteria. The criteria for the pull out test requires that the ultimate failure force must be a minimum of three times the safe working pull out load published by the manufacturer.

The criteria for the slip test requires the force needed to give a continuous slip must be no less than three times the safe working slip load published by the manufacturer.

Pull Out TestThis test involves the M12 nut fixing being done up to 70Nm torque and pulled vertically from a 300mm strut lying horizontally. The strut must be secured to a rigid structure giving a free length of channel 100mm long, and the fixing pulled vertically away from it until the strut breaks. As shown in figure .

Slip TestThis test also involves the M12 nut fixing being tightened to 70Nm but this time the strut is mount-ed vertically and the fixing being pushed down the length of strut, measuring the maximum force needed to do this. As shown in figure.

Specimen Maximum Force (N)1 255632 281433 269744 266115 251756 24470Mean 26156

Specimen Maximum Force (N)1 155402 126563 125084 14525Mean 13807

Test Results

Test Results

Test Procedure

20

CHANNEL PRODUCT TESTING - Pull ApartPull Apart Spot Weld TestThis test involves the standard 41mm x 82 mm x 2.5 mm back to back channels and is carried out in accordance with ISO 9001:2008 quailty standards. Data listed in PSI (Pound per inch) and is the force required to initally start to separate the weld spots on the back to back channels. Please refer to image below.

Test Number 41mm x 82mm x 2.5mm Plain Channel 41mm x 82mm UltraSTRUT Channel1 2050PSI 1800PSI2 2100PSI 1750PSI3 2100PSI 1750PSI4 2100PSI 1750PSI5 2150PSI 1800PSI6 2050PSI 1800PSI7 2100PSI 1700PSI8 2050PSI 1700PSI9 2050PSI 1750PSI10 2100PSI 1800PSI11 2100PSI 1800PSI12 2100PSI 1850PSIAverage 2088PSI 1767PSI

Test Results

Kwik-Smart 21


Kit Includes:2 off Cantilever Bracket2 off Plastic End Caps8 off M10 Flat Washers4 off M10 Channel Spring Nuts4 off M10 x 30 mm Set ScrewsWall fixings available on request

Standard Offering:Is UltraSTRUT 2.5mmAvaliable on Request

Part No. Lengthmm

Max LoadUniformaly Distributed

UB150 150 815UB300 300 450UB450 450 315UB600 600 225UB750 750 175

Part No. Lengthmm


UB150 Kit 150 815UB300 Kit 300 450UB450 Kit 450 315UB600 Kit 600 225UB750 Kit 750 175

Part No. Lengthmm


BC150 150 900BC300 300 780BC450 450 530BC600 600 390BC750 750 320

Part No. Lengthmm


BC150 Kit 150 900BC300 Kit 300 780BC450 Kit 450 530BC600 Kit 600 390BC750 Kit 750 320

UB150 - UB750 [HDG / SS]

BC150 - BC750 [HDG / SS]

Cantilever Bracket Un-Braced

CANTILEVER BRACKETs

Cantilever Bracket Braced

Cantilever Bracket Kit

BracedUn-Braced

Binder Group offers an exclusive range of Australian made Cantilever Brackets construct-ed from our revolutionary Ultrastrut channel. By doing this our range of braced and non-braced cantilevers offers the installer:

• A lighter weight cantilever with the same struc-tural integrity as much heavier 2.5mm Cantile-vers.

• Slotted horizontals to stop dust and water build up.

Over and above an easier and more cost effec-tive installation for the contractor with a unique aesthetic appeal.

22


Part No. Height (D)

Width (E)

Thick-ness

Slot Length

KS240-0* 30 30 2.5 11 x 25 3000KS240-1 40 40 3 8 x 25 3750KS240-2 40 40 5 8 x 25 3750KS240-4 40 40 3 11 x 25 3000KS240-5 40 40 5 11 x 25 3750

Part No. Description

TK-150 150mmTK-300 300mmTK-450 450mmTK-600 600mmTK-750 750mm

Part No. Width (E) Thick-ness

Slot Length

KS246-1 40 5 8 x 25 3000KS246-2 40 5 11 x 25 3000

•Supplied in 3750mm lengths.•Other sizes available on order.Note:*240-0 supplied in Zinc Plated finish.*240-0 supplied in 3000mm lengths.

•Supplied in 3.0 mm lengths.•Other sizes available on order.

Slotted Angle [HDG]

UltraSTRUT Trapeze Kit

Slotted Flat Bar [HDG]HANGER FITTINGS AND PUNCHED ANGLE

Kit Includes:UltraSTRUT Channel(cut to required size) 2 Threaded Rod6 Washer6 Nuts

CHANNEL FITTINGS

Kwik-Smart 23


KS1062- KS1964

Part No.

Bolt Size

Hole Size

Masskg/100

KS1062 08 9 7.0KS1063 10 12 6.8KS1064 12 14 6.6KS1964 16 18 6.4

KS1026

KS1941

KS1186/2106/2108

KS1066

KS1325

KS1031

KS1065

KS1326

KS1036

KS1038

KS1067

KS2484

KS1358

KS1037KS2101/2103

Flat Plate Fittings

Angle Fittings

Other finsihes available upon request.

Channel Fittings Key to finishes:GB= Galvanised BondHDG =Hot Dip Galvanised

SS=Stainless Steel

CHANNEL FITTINGS

24

KS1034KS1035

KS1045

KS2072A

KS1033

KS1047

KS2073

KS1359

KS4045

KS2072B

KS1357

KS4047

Angle Fittings

Post Base

“Z” Shape Fittings “U” Shape Fittings

When ordering, please quote Part Number for required size and surface finish.Other finsihes available upon request.


SS=Stainless Steel

CHANNEL FITTINGS

Kwik-Smart 25


KS2785

KS1796

KS2855

KS1379

KS2676

KS2377

Flange Clamp Z/P

KS0615

KS1272

KS1386

KS3016

KS1271

Beam Clamps

Electrical Fittings

Other finsihes available upon request.


SS=Stainless Steel

Binder Tray

26

Binder Tray - BT3

BT3 - Application

Part No. DescriptionBT3-150 BT3 Cable Tray 150mm GBBT3-300 BT3 Cable Tray 300mm GBBT3-450 BT3 Cable Tray 450mm GBBT3-600 BT3 Cable Tray 600mm GBBT3-HDB BT3 Hold Down Bracket GBBT3-LP BT3 Link Plate GBBT3-RP BT3 Radius Plate GBBT3-SP BT3 Splice Plate GBBT3-TX BT3 TX Bracket GB

Splice Plate

Riser Links

Nut & Bolt

Divider Strip

TX Bracket

Application 1 Application 2


Radius Plate

Trapeze Bracket

Hold Down Bracket

Binder Tray

Kwik-Smart 27

Binder Tray - BT5

BT5 - Application

Part No. Max LoadUniformaly Distributed

BT5-150 BT5 Cable Tray 150mm GBBT5-300 BT5 Cable Tray 300mm GBBT5-450 BT5 Cable Tray 450mm GBBT5-600 BT5 Cable Tray 600mm GBBT5-HDB BT5 Hold Down Bracket GBBT5-LP BT5 Link Plate GBBT5-RP BT5 Radius Plate GBBT5-SP BT5 Splice Plate GBBT5-TX BT5 TX Bracket GB

Splice Plate

Riser Links

Nut & Bolt

Divider Strip

TX Bracket



Radius Plate

Hold Down Bracket

Binder Tray

28

BT3- LOAD RATING AND DEFLECTION

BT5- LOAD RATING AND DEFLECTION

Binder cable ladder

Kwik-Smart 29

When ordering, please specify required type, width and surface finish.

NEMA 12B CABLE LADDER

NEMA 16A CABLE LADDER

NEMA 20C CABLE LADDER

• Standard Length 3.0 metres and 6.0 metres.• Standard FInish HDG• Other Finishes available on request.• Rung Spacing 300mm.• Standard Width : 150mm. 300mm, 450mm,

600mm.• Load Data - 3 metre simple beam 125kg/m. - 6 metre simple beam 31 kg/m.

(Note design working load is distributed laterally and longitudially over the span with a factor of safety of 2.)

Binder Group distributes a comprehensive range of Nema Cable ladders for the ElectricalIndustry, load rated to NEMA Standard VE1.

All of Binder Group’s cable ladder offerings come with an extensive range of finishing components and joining hardware to cater for the smallest commercial applications to the largest of Industrial plant applications including but not limited to:

Risers, Tees, Crosses, Reducers, Hinged Horizontal and Vertical Splices, Adjustable Risers, Covers, Divider Strip, Adjustable Cantilever Support Brackets and Cable Clamps.

All of Binder Groups Nema cable ladder solutions are available in Steel, Hot dipped galvanized steel, Aluminium, Stainless, Epoxy painted steel or FRP fiberglass.

Binder Cable Ladder

“RI - Rail In Series

“RI - Rail In Series

“RO - Rail Out Series

“RO - Rail Out Series

Binder cable ladder

30

When ordering, please specify required type, width and surface finish.

Flat Bends

Reducers

Tee & Flat Cross

• All Bends are pre-punched for direct connection to cable ladder widths

• Bends availble in standard cable ladder widths.• Standard Finish HDG• Other Finishes available on request.

• All Reducers are pre-punched for direct con-nection to cable ladder widths

• Reducers availble in standard cable ladder widths.

• Standard Finish HDG• Other Finishes available on request.

• All Crosses and Tees are pre-punched for di-rect connection to cable ladder widths

• Crosses and Tees availble in standard cable ladder widths.

• Standard Finish HDG• Other Finishes available on request.

Risers• All Riser are pre-punched for direct connection

to cable ladder widths• Riser availble in standard cable ladder widths.• Standard Finish HDG• Other Finishes available on request.

External RiserInternal Riser

Righthand - Resucers

Lefthand - Resucers

Horizontal- TEE

Flat Cross

Straight - Resucers

CHANNEL NUTS

Kwik-Smart 31


For 41 x 41 Channels, with Spring



Slick Strut Nut

Flange Clamp Z/P Drilled Lock Nut

For 41 x 41 Channels, without Spring



Wedge Nut

Part No. SizeKS1006 M06KS1007 M08KS1008 M10KS1010 M12KS1012S M16

Part No. SizeKS4006 M06KS4007 M08KS4008 M10KS4010 M12KS4012S M16

Part No. SizeKS5508 M10KS5510 M12

Part No. SizeSN06 M06SN08 M08SN10 M10SN12 M12

Part No. SizeFC08 M08FC10 M10FC12 M12

Part No. SizeLN08 M08LN10 M10LN12 M12LN16 M16

Part No. SizeKS3016 M06KS3006 M06KS3007 M08KS3008 M10KS3010 M12KS3012 M16



Part No. SizeWDG08 M08WDG10 M10WDG12 M12


CHANNEL NUTS

32


Hex Nut CL.8 Zinc

Mud Guard Washers

Lock Washers

Drop in Anchor ZP

Flat Washer CS Zinc

Spring WashersHex Head Set Screws

Part No. SizeHN06 M06HN08 M08HN10 M10HN12 M12HN16 M16

Part No.MW-1/4X3/4MW-1/4X1MW-1/4X1 1/4MW-3/8X1 1/4

Part No. SizeLW06 M06LW08 M08LW10 M10LW12 M12LW16 M16

Part No. SizeDIA0625 M06DIA0825 M08DIA1030 M10DIA1040 M10DIA1050 M10DIA1250 M12

Part No. SizeFW06 M06FW08 M08FW10 M10FW12 M12FW16 M16

Part No. SizeSW06 M06SW08 M08SW10 M10SW12 M12SW16 M16

Part No. SizeHHS0620 M06HHS0625 M06HHS0650 M06HHS0825 M08HHS0839 M08HHS0840 M08HHS1020 M10HHS1025 M10HHS1030 M10HHS1040 M10HHS1045 M10HHS1050 M10HHS1060 M10HHS1225 M12HHS1230 M12HHS1240 M12HHS1250 M12HHS1260 M12HHS1280 M12HHS1640 M16HHS1650 M16HHS1660 M16HHS1665 M16

Hanger Bolts [ZP]

Part No.HB1080HB10100HB10120HB10140

CHANNEL NUTS

Kwik-Smart 33


Vertical Wall Plate [Z/P]

Horizontal Wall Plate [Z/P]

Wall Plate [Z/P]

‘C’ Purlin Clip [Z/P]

Hex Connector [Z/P, HDG - POA]

Female Wall Plate [Z/P]

Suspension Eye [Z/P]

‘Z’ Purlin Clip [Z/P]

Clevis Hanger [HDG]

Threaded Rod R/H Zinc Gr.4.6

Part No. SizeTR06 M06TR08 M08TR10 M10TR12 M12TR16 M16

Part No. SizeVWP10 M10VWP12 M12

Part No. SizeHWP10 M10HWP12 M12

Part No. SizeWP10 M10

Part No. SizeCPC10 M10

Part No. SizeHC10 M10

HC12 M12

HC16 M16

Part No. SizeFWP10 M10FWP12 M12

Part No. SizeSE10 M10

Part No. SizeZPC10 M10

Part No. SizeCH10 M10CH12 M12


CLIPS & CLAMPS

34


•Includes nut and screw•Fits standard strut channel•Also Available in Hot Dip Galvanised or Stain-less Steel

Part No. Dimensionmm

KS2024 08KS2025 11KS2026 14KS2027 17KS2028 19KS1111 21KS2029 22KS2030 25KS1112 27KS2031 29KS2032 32KS1113 34KS2033 35KS2034 38KS1114 42KS2036 44KS1115 48KS2037 49KS2038 51KS2039 54KS2040 57KS1117 60KS2042 64KS2043 67KS2044 70KS1118 73KS2046 76KS2047 79KS2048 83KS2049 86KS1119 90

Part No. Dimensionmm

KS2051 92KS2052 95KS2053 98KS1120 102KS2055 105KS2056 108KS2057 111KS1121 114KS2059 117KS2060 121KS2061 123KS2062 127KS2063 130KS2064 133KS2065 136KS2066 140KS2067 143KS2068 146KS2069 149KS2070 152KS2070-62 159KS2070-64 165KS2070-66 171KS2070-70 178KS2070-72 184KS2070-74 191KS2070-76 197KS2070-80 203KS2070-84 216KS2070-90 232KS2070-110 315

KS2024 Series Channel Clips (ZP/HDG/SS)


Note: When used in the application illustrated it is recommended that the lower clamp be supported against possible slippage.

KS1064Bracket

Load

CLIPS & CLAMPS

Kwik-Smart 35


CCC Series Channel Clip

CCP Series Channel Clip

Channel Clip for Copper Pipe

• Channel Clip sizes 15mm to 300mm• Standard finish Powder Coated Brown• Fits standard channel.

Channel Clip for PVC Pipe

• Channel Clip sizes 40mm to 375mm• Standard finish Powder Coated White• Fits standard channel.

Part No. Product DescriptionCCC-15 15Cu Channel Clip CCC-20 20Cu Channel Clip CCC-25 25Cu Channel Clip CCC-32 32Cu Channel Clip CCC-40 40Cu Channel Clip CCC-50 50Cu Channel Clip CCC-65 65Cu Channel Clip CCC-80 80Cu Channel Clip CCC-100 100Cu Channel Clip CCC-125 125Cu Channel Clip CCC-150 150Cu Channel Clip CCC-200 200Cu Channel Clip

Part No. Product DescriptionCCP-40 40PVC Channel Clip CCP-50 50PVC Channel Clip CCP-65 65PVC Channel Clip CCP-80 80PVC Channel Clip CCP-90 90PVC Channel Clip CCP-100 100PVC Channel Clip CCP-150 150PVC Channel Clip CCP-225 225PVC Channel Clip CCP-300 300PVC Channel Clip CCP-375 375PVC Channel Clip

CLIPS & CLAMPS

36


PCP Series Channel Clip

BSC Series Channel Clip

Channel Clip for Pressure PVC Pipe

• Channel Clip sizes 15mm to 250mm• Standard finish Powder Coated White• Fits standard channel.

Binsul Clamp

• Insulates against heat loss and gain.• Reduces Vibration.• Temperature range - 30 0 C to 1250 C.• Fits standard channel.

Part No. Product Description PCP-15 15PVC Pressure Channel Clip PCP-20 20PVC Pressure Channel Clip PCP-25 25PVC Pressure Channel Clip PCP-32 32PVC Pressure Channel Clip PCP-40 40PVC Pressure Channel Clip PCP-50 50PVC Pressure Channel Clip PCP-65 65PVC Pressure Channel Clip PCP-80 80PVC Pressure Channel Clip PCP-100 100PVC Pressure Channel Clip

Part No. Imperial Pipe SizeInches

Pipe Diametermm

BSC-1/4 1/4 6.35 BSC-3/8 3/8 9.53 BSC-1/2 1/2 12.70 BSC-5/8 5/8 15.88 BSC-3/4 3/4 19.05 BSC-7/8 7/8 22.23 BSC-1 1/8 1 1/8 28.58 BSC-1 3/8 1 3/8 34.93 BSC-1 5/8 1 5/8 42.75 BSC-2 1/8 2 1/8 53.98 BSC-2 5/8 2 5/8 66.68 BSC-3 1/8 3 1/8 79.38 BSC-3 5/8 3 5/8 92.08

CLIPS & CLAMPS

Kwik-Smart 37


• Suitable for Steel, Copper or PVC pipe from 15NB to 150NB.• Finish must be stated.

• Smooth inner surface to allow pipe to move.• Plastic Spacers prevent over tightening.• Suitable for HDPE pipe from 25mm to 150mm.

Part No. Pipe sizeNB

Pipe ODmm

Size Rangemm

Box Qty

KS10-15 15 Cu 12.7 12-14 150KS10-20 20 Cu 19 15-19 150KS10-25 25 Cu 25.4 24-26 100KS10-32 32 Cu 31.8 30-33 50KS10-40 40 Cu / PVC 38.1 38-41 50KS10-50 50 Cu / PVC 51.2 50-56 50KS10-65 65 Cu 63.5 63-67 50KS10-65A 65 PVC 69.1 70-73 50KS10-80 80 Cu / PVC 76.2 74-80 50KS10-100 100 Cu 101.6 101-106 25KS10-100A 100 PVC 110.4 108-114 25KS10-150 150 PVC 160.5 159-164 20

Material : Carbon Steel / Stainless Steel. Finish : Zinc /Mill

Material : Carbon Steel. Finish : Zinc.

Part No. Pipe SizeNB

Size Rangemm

KS12-25 25 HDPE 25-28 KS12-32 32 HDPE 31-35 KS12-40 40 HDPE 38-43 KS12-50 50 HDPE 48-53 KS12-63 63 HDPE 64-67 KS12-75 75 HDPE 73-78 KS12-90 90 HDPE 86-91 KS12-110 110 HDPE 108-116 KS12-160 160 HDPE 158-163

KS10 Kwik Clips

KS12 Dual Clip ( for Plastic Pipe)

CLIPS & CLAMPS

38


Nut Clip For Copper Pipe

Nut Clip For PVC Pipe

Pressure Pipe Clip

Filbows

Part No. Description NC15-C 15Cu Nut Clip NC20-C 20Cu Nut Clip NC25-C 25Cu Nut Clip NC32-C 32Cu Nut Clip NC40-C 40Cu Nut Clip NC50-C 50Cu Nut Clip NC65-C 65Cu Nut Clip NC80-C 80Cu Nut Clip NC100-C 100Cu Nut Clip NC125-C 125Cu Nut Clip NC150-C 150Cu Nut Clip

Part No. Description NC40-P 40PVC Nut Clip NC50-P 50PVC Nut Clip NC65-P 65PVC Nut Clip NC80-P 80PVC Nut Clip NC90-P 90PVC Nut Clip NC100-P 100PVC Nut Clip NC150-P 150PVC Nut Clip

Part No. Description KS109-40 40Press Pipe Clip KS109-50 50Press Pipe Clip KS109-80 80Press Pipe Clip KS109-100 100Press Pipe Clip KS109-150 150Press Pipe Clip KS109-200 200Press Pipe Clip KS109-250 250Press Pipe Clip KS109-300 300Press Pipe Clip

• Nut clip sizes 15mm to 150mm.• Cup head fastener.• Double bolted.• Suits M10 Rod.• Standard finsih powder coated brown.

• Nut clip sizes 40mm to 150mm.• Cup head fastener.• Double bolted.• Suits M10 Rod.• Standard finsih powder coated white.

• Nut clip sizes 40mm to 150mm.• Cup head fastener.• Double bolted.• Suits M10 Rod.• Standard finsih powder coated white.

Part No. Description FB40-P 40PVC Filbow FB50-P 50PVC Filbow FB65-P 65PVC Filbow FB80-P 80PVC Filbow FB100-P 100PVC Filbow FB150-P 150PVC Filbow FB225-P 225PVC Filbow FB300-P 300PVC Filbow

• Yoke clamp sizes 40mm to 300mm.• Standard finsih powder coated white.

CLIPS & CLAMPS

Kwik-Smart 39


Yoke Clamp for Copper Pipe

Yoke Clamp For PVC Pipe [M08]

Yoke Clamp For PVC Pipe [M12]

Part No. Description YC50-P8 50PVC Yoke Clamp YC80-P8 80PVC Yoke Clamp

• Yoke clip sizes 15mm to 100mm.• Adjustable yoke 48mm to 65mm.• Double bolted.• Suits up to M8 Rod.• Standard finsih powder coated white.

Part No. Description YC20-C 20Cu Yoke Clamp YC25-C 25Cu Yoke Clamp YC32-C 32Cu Yoke Clamp YC40-C 40Cu Yoke Clamp YC50-C 50Cu Yoke Clamp YC65-C 65Cu Yoke Clamp YC80-C 80Cu Yoke Clamp YC100-C 100Cu Yoke Clamp YC125-C 125Cu Yoke Clamp YC150-C 150Cu Yoke Clamp

• Yoke clamp sizes 20mm to 300mm.•Adjustable yoke 48mm to 65mm.• Double bolted.• Suits up to M12 Rod.• Standard finsih powder coated brown.

Part No. Description YC40-P 40PVC Yoke Clamp YC50-P 50PVC Yoke Clamp YC65-P 65PVC Yoke Clamp YC80-P 80PVC Yoke Clamp YC100-P 100PVC Yoke Clamp YC150-P 150PVC Yoke Clamp YC225-P 225PVC Yoke Clamp YC300-P 300PVC Yoke Clamp

• Yoke clamp sizes 40mm to 300mm.•Adjustable yoke 48mm to 65mm.• Double bolted.• Suits up to M12 Rod.• Standard finsih powder coated white.

CLIPS & CLAMPS

40


BG100 - Light Duty 2-Bolt Pipe Clamp

•Also avaliable in stainless steel, zinc or powder coated white.

Material : Carbon Steel. Finish : HDG.

Part No. Steel Pipe Size

Pipe OD

Material WxT

BG100-15 15 NB 21.3 25 x 3 BG100-20 20 NB 26.7 25 x 3 BG100-25 25 NB 33.4 25 x 3 BG100-32 32 NB 42.2 32 x 3 BG100-40 40 NB 48.3 32 x 3 BG100-50 50 NB 60 40 x 3 BG100-65 65 NB 76 40 x 3 BG100-80 80 NB 89 40 x 3 BG100-100 100 NB 114 40 x 3 BG100-125 125 NB 140 40 x 5 BG100-150 150 NB 168 40 x 5 BG100-200 200 NB 220 50 x 6 BG100-225 225 NB 245 50 x 6 BG100-250 250 NB 273 50 x 6 BG100-300 300 NB 324 50 x 10 BG100-350 350 NB 356 65 x 10 BG100-400 400 NB 406 65 x 12 BG100-450 450 NB 457 75 x 16 BG100-500 500 NB 508 75 x 16 BG100-600 600 NB 610 75 x 16 BG100-750 750 NB 762 90 x 20 BG100-900 900 NB 914 100 x 25

Part No. Copper Tube Size

Pipe OD

Materail WxT

BG100-50CU 50 CU 51 32 x 3 BG100-65CU 65 CU 63 40 x 3 BG100-80CU 80 CU 76 40 x 3 BG100-100CU 100 CU 102 40 x 3 BG100-125CU 125 CU 127 40 x 5 BG100-150CU 150 CU 152 40 x 5 BG100-200CU 200 CU 255 40 x 5 BG100-250CU 250 CU 257 50 x 6 BG100-300CU 300 CU 304 50 x 6

Part No. PVC Pipe Size

Pipe OD

Material WxT

BG100-40PP 40PP 48 32 x 3 BG100-50PP 50 PP 56 32 x 3 BG100-65PP 65 PP 69.1 40 x 3 BG100-80PP 80 PP 82.7 40 x 3 BG100-100PP 100 PP 114 40 x 3 BG100-150PP 150 PP 160 40 x 5 BG100-200PP 200 PP 225 50 x 6 BG100-225PP 225 PP 251 50 x 6 BG100-250PP 250 PP 281 50 x 6 BG100-300PP 300 PP 315 50 x 6

CLIPS & CLAMPS

Kwik-Smart 41


• HDPE sizes also available.• Copper tube should be isolated from galvanised steel.• Avaliable in powder coated finish.


Part No. Copper Pipe Size Bolt Hole Diameter

MaterialNormal

SizeOutside

DiameterW x T

BG105-15CU 15 CU 12.7 8 25 x 3 BG105-20CU 20 CU 19 8 25 x 3

BG105-25CU 25 CU 25.4 8 25 x 3 BG105-32CU 32 CU 31.8 8 25 X 3 BG105-40CU 40 CU 38.1 11 32 x 3 BG105-50CU 50 CU 51.2 11 32 X 3 BG105-65CU 65 CU 63.5 14 40 x 3 BG105-80CU 80 CU 76.2 14 40 x 3 BG105-100CU 100 CU 101.6 14 40 x 3 BG105-125CU 125 CU 152.4 14 40 x 5

Part No. Steel Pipe Size Bolt Hole

Diame-ter

Material Normal

SizeOutside

DiameterW x T

BG105-15NB 15 NB 21 8 25 x 3 BG105-20NB 20 NB 27 8 25 x 3 BG105-25NB 25 NB 34 8 25 x 3BG105-32NB 32 NB 43 11 32 X 3 BG105-40NB 40 NB 48 11 32 x 3 BG105-50NB 50 NB 60 11 32 X 3 BG105-65NB 65 NB 75 14 40 x 3 BG105-80NB 80 NB 89 14 40 x 3 BG105-100NB 100 NB 114 14 40 x 3 BG105-150NB 150 NB 768 14 40 x 5 BG105-200NB 200 NB 220 18 50 x 6 BG105-225NB 225 NB 245 18 50 x 6 BG105-250NB 250 NB 273 18 50 x 6

Part No. PVC Pipe Size Bolt Hole

Diame-ter

Material Normal

SizeOutside

DiameterW X T

BG105-50PVC 50 PVC 59 11 32 x 3BG105-65PVC 65 PVC 69.1 14 40 x 3 BG105-80PVC 80 PVC 82.7 14 40 x 3BG105-100PVC 100 PVC 110.4 14 40 x 3BG105-150PVC 150 PVC 160.5 14 40 x 5

BG105 Saddle Guide

CLIPS & CLAMPS

42


BG106 Saddle Clamp


• HDPE sizes also available.• Copper tube should be isolated from galvanised steel.• Avaliable in powder coated finish.


Part No. Copper Pipe Size Bolt Hole Diameter

MaterialNormal

SizeOutside

DiameterW x T

BG106-15CU 15 CU 12.7 8 25 x 3 BG106-20CU 20 CU 19 8 25 x 3

BG106-25CU 25 CU 25.4 8 25 x 3 BG106-32CU 32 CU 31.8 8 25 X 3 BG106-40CU 40 CU 38.1 11 32 x 3 BG106-50CU 50 CU 51.2 11 32 X 3 BG106-65CU 65 CU 63.5 14 40 x 3 BG106-80CU 80 CU 76.2 14 40 x 3 BG106-100CU 100 CU 101.6 14 40 x 3 BG106-125CU 125 CU 152.4 14 40 x 5

Part No. Steel Pipe Size Bolt Hole

Diame-ter

Material Normal

SizeOutside

DiameterW x T

BG106-15NB 15 NB 21 8 25 x 3 BG106-20NB 20 NB 27 8 25 x 3 BG106-25NB 25 NB 34 8 25 x 3BG106-32NB 32 NB 43 11 32 X 3 BG106-40NB 40 NB 48 11 32 x 3 BG106-50NB 50 NB 60 11 32 X 3 BG106-65NB 65 NB 75 14 40 x 3 BG106-80NB 80 NB 89 14 40 x 3 BG106-100NB 100 NB 114 14 40 x 3 BG106-150NB 150 NB 768 14 40 x 5 BG106-200NB 200 NB 220 18 50 x 6 BG106-225NB 225 NB 245 18 50 x 6 BG106-250NB 250 NB 273 18 50 x 6

Part No. PVC Pipe Size Bolt Hole

Diame-ter

Material Normal

SizeOutside

DiameterW X T

BG106-50PVC 50 PVC 59 11 32 x 3BG106-65PVC 65 PVC 69.1 14 40 x 3 BG106-80PVC 80 PVC 82.7 14 40 x 3BG106-100PVC 100 PVC 110.4 14 40 x 3BG106-150PVC 150 PVC 160.5 14 40 x 5

CLIPS & CLAMPS

Kwik-Smart 43


BG107 U Bolt Clamp Light Duty

BG107 U Bolt Clamp

• Other sizes available on order.• Mill finish available by request.• Comes with 2 hex nuts.

• Other sizes available on order.

Material : Carbon Steel / Stainless Steel. Finish : HDG / Mill.

Material : Carbon Steel / Stainless Steel. Finish : ZP / Mill.

Part No. Pipe Size ThreadSize

Centres Height to inside

Normal Size

Outside Diame-

ter

mm mm

BG107-15 15 NB 21.3 M10 31 67 BG107-20 20 NB 26.7 M10 37 77 BG107-25 25 NB 33.4 M10 44 85 BG107-32 32 NB 42.2 M10 53 92 BG107-40 40 NB 48.3 M10 58 100 BG107-50 50 NB 60.3 M10 70 110 BG107-80 80 NB 88.9 M12 101 140 BG107-100 100 NB 114.3 M12 126 165 BG107-125 125 NB 141.3 M12 152 187 BG107-150 150 NB 168.3 M12 180 220 BG107-200 200 NB 219.1 M16 236 295 BG107-250 250 NB 273.0 M20 293 340

Part No. DiameterCentres Hight to

insidemm mm

BG107CON-20 U-Bolt 20mm 28 40 BG107CON-25 U-Bolt 25mm 34 44 BG107CON-30 U-Bolt 30mm 42 51 BG107CON-40 U-Bolt 40mm 50 60BG107CON-50 U-Bolt 50mm 60 70

Material Cross-Linked Closed Cell PE Foam

Density 300 Kg/m2Moisture Absorption(by weight, room temp, 5hrs)

<1%

Tensile Strength 26.4 Kg/m2Tear Strength 8.3 Kg/m2Thermal Conductivity(ISO 6302-1991)

0.065

Constant WorkingTemperature

-40°c to 150°c

Compressive Strength JIS 6767 3.4 Kg/cm2

PE Poly BlockHot & Cold Pipe Supports

FEATURES– PE Block profile ensures an airtight finish– PE Block decreases installation time as it locks easily together– Closed cell so that it will not absorb moisture or degrade with time.– Made of high density PE Foam– Will not with pipe movement– AS1530.3 compliant foil faced– Made from recycled material and is recyclable

Built in LocOnce tightly taped, PE Block will pre-vent any air movement through the join. This is especially important in cold line applications to prevent poten-tial air condensation

Tough & DurablePE Block pipe supports are made of high density, crosslinked, closed cell polyethylene foam. As they are closed cell they absorb negligible moisture, and retain their insulation properties throughout the life of the installation.

Non Erosion with Pipe MovementPipes move with contraction and ex-pansion, eroding the ferrule. The tough PE foam will resist movement and pre-vent gap formation over time.

Health & SafetyAs the blocks are preformed there is no need for cutting, so there is no dust and no mess. They do not emit fibrous particles during installation or over time.

Performance LifePE Block is closed cell and unaffected by water and humidity. This ensures continual performance over the life of the installation.

Chemical ResistancePE Block is resistant to detergents, diluted acids, alkalis, alcohols, esters and fungi ensuring performance in even the most demanding applica-tions. PE Block is light weight and ex-tremely tough. Just place the two piec-es over the pipe, squeeze together

gently, and apply AS1530.3 approved foil tape ensuring complete coverage.

Compliance with BCA Fire Hazard PropertiesPE Block complies with the Building Code of Australia (BCA) specification C1.10 Fire hazard properties for mate-rials used in Class 2 - 9 buildings.

Quick, Easy & Safe ApplicationNo more cutting. This ensures a flat surface to butt insulation against, al-lowing a tight and secure joint. No fibre’s, no dust, no mess to clean up afterwards. No special face masks or gloves required.

Wall Thickness Available20 mm, 25 mm, 38 mm, 50 mm walls and made to order wall thickness and ID

Length Along PipeThe standard “on pipe” length is 50 mm. 75 mm is available on request.

Advantage to Installers

Technical Specification

PE POLY BLOCK

Kwik-Smart 45


FEATURES• PE Block profile ensures an airtight finish• PE Block decreases installation time as it locks easily together• Closed cell so that it will not absorb moisture or degrade with time.• Made of high density PE Foam• Will not with pipe movement• AS1530.3 compliant foil faced• Made from recycled material and is recyclable

19mm Wall Thickness

Part No. ID OD

PE-10X19X48 10ID 48ODPE-13X19X51 13ID 51ODPE-16X19X54 16ID 54ODPE-19X19X57 19ID 57ODPE-22X19X60 22ID 60ODPE-28X19X66 28ID 66ODPE-35X19X73 35ID 73ODPE-42X19X74 42ID 74ODPE-54X19X92 54ID 92ODPE-38X19X76 38ID 76ODPE-42X19X79 42ID 79ODPE-45X19X83 45ID 83ODPE-48X19X86 48ID 86ODPE-51X19X90 51ID 90ODPE-54X19X92 54ID 92ODPE-57X19X95 57ID 95ODPE-60X19X98 60ID 98ODPE-64X19X102 64ID 102ODPE-67X19X105 67ID 105ODPE-73X19X111 73ID 111ODPE-76X19X114 76ID 114OD

13mm Wall Thickness

Part No. ID OD

PE-10X13X35 10ID 35ODPE-13X13X38 13ID 38ODPE-16X13X42 16ID 42ODPE-19X13X44 19ID 44ODPE-22X13X48 22ID 48ODPE-25X13X51 25ID 51ODPE-28X13X54 28ID 54ODPE-32X13X57 32ID 57ODPE-35X13X60 35ID 60ODPE-38X13X64 38ID 64ODPE-42X13X67 42ID 67ODPE-45X13X70 45ID 70ODPE-48X13X73 48ID 73ODPE-51X13X76 51ID 76ODPE-54X13X79 54ID 79ODPE-57X13X83 57ID 83ODPE-60X13X86 60ID 86ODPE-64X13X90 64ID 90ODPE-67X13X92 67ID 92ODPE-73X13X98 73ID 98OD

PE-76X13X102 76ID 102 OD

PE Block

PE POLY BLOCK

46

25mm Wall ThicknessPart No. ID ODPE-10X25X60 10ID 60ODPE-13X25X68 13ID 68ODPE-16X25X64 16ID 64ODPE-19X25X77 19ID 77ODPE-22X25X73 22ID 73ODPE-25X25X80 25ID 80ODPE-28X25X79 28ID 79ODPE-32X25X86 32ID 86OD

PE-35X25X86 35ID 86ODPE-38X25X93 38ID 93ODPE-42X25X92 42ID 92ODPE-45X25X95 45ID 95ODPE-48X25X98 48ID 98ODPE-51X25X106 51ID 106ODPE-54X25X105 54ID 105ODPE-57X25X108 57ID 108ODPE-60X25X111 60ID 111ODPE-64X25X118 64ID 118ODPE-67X25X117 67ID 117ODPE-73X25X123 73ID 123ODPE-76X25X131 76ID 131ODPE-102X25X156 102ID 156OD

38mm Wall ThicknessPart No. ID ODPE-10X38X86 10ID 86ODPE-13X38X93 13ID 93OD

PE-16X38X92 16ID 92ODPE-19X38X106 19ID 106ODPE-25X38X106 25ID 106ODPE-32X38X118 32ID 118ODPE-38X38X118 38ID 118ODPE-51X38X131 51ID 131ODPE-64X38X144 64ID 144ODPE-76X38X156 76ID 156ODPE-102X38X182 102ID 182ODPE-127X38X207 127ID 207ODPE-152X38X234 152ID 234ODPE-22X38X98 22ID 98ODPE-28X38X104 28ID 104OD

50mm Wall ThicknessPart No. ID ODPE-10X50X108 10ID 108ODPE-13X50X118 13ID 118ODPE-16X50X114 16ID 114ODPE-19X50X131 19ID 131ODPE-25X50X131 25ID 131ODPE-32X50X144 32ID 144ODPE-38X50X144 38ID 144ODPE-51X50X156 51ID 156ODPE-64X50X168 64ID 168ODPE-76X50X182 76ID 182ODPE-102X50X202 102ID 202ODPE-127X50X232 127ID 232ODPE-152X50X258 152ID 258OD

PE Block



PE POLY BLOCK

Kwik-Smart 47


KS2600 Isolation Barrier

KS680001 Binder Sil Tape

Wood Block Cork Block

PE Block with Clip

Form barrier between copper tube and clip/channel

50mm x 20mm Roll 50mm x 10mm Roll •Available in all Pipe / Tube Diameters.•Available in Insulation Thickness from 10mm to 100mm.


19mm Wall ThicknessPart No. ODPEC-19X48 48ODPEC-19X51 51ODPEC-19X54 54ODPEC-19X54 54ODPEC-19X60 60ODPEC-19X64 64ODPEC-19X67 67ODPEC-19X70 70ODPEC-19X73 73ODPEC-19X76 76ODPEC-19X79 79ODPEC-19X83 83ODPEC-19X86 86ODPEC-19X90 90ODPEC-19X92 92ODPEC-19X95 95ODPEC-19X98 98OD

PEC-19X102 102ODPEC-19X105 105ODPEC-19X111 111ODPEC-19X114 114OD

25mm Wall ThicknessPart No. ODPEC-25X60 60ODPEC-25X64 64ODPEC-25X67 67ODPEC-25X70 70ODPEC-25X73 73ODPEC-25X76 76ODPEC-25X79 79ODPEC-25X83 83ODPEC-25X86 86ODPEC-25X90 90ODPEC-25X92 92ODPEC-25X95 95ODPEC-25X92 98ODPEC-25X102 102ODPEC-25X105 105ODPEC-25X108 108ODPEC-25X111 111ODPEC-25X114 114ODPEC-25X117 117ODPEC-25X123 123ODPEC-25X127 127OD

13mm Wall ThicknessPart No. ODPEC-13X35 35ODPEC-13X38 38ODPEC-13X42 42ODPEC-13X44 44ODPEC-13X48 48ODPEC-13X51 51ODPEC-13X54 54ODPEC-13X57 57ODPEC-13X60 60ODPEC-13X64 64ODPEC-13X67 67ODPEC-13X70 70ODPEC-13X73 73ODPEC-13X76 76ODPEC-13X79 79ODPEC-13X83 83ODPEC-13X86 86ODPEC-13X90 90ODPEC-13X92 92ODPEC-13X98 98ODPEC-13X102 102OD

PIPE SUPPORT

48

Pipe Expansion Data

Expansion chart for various pipe and tubes Metal and synthetics (plastic) pipes contract with cold and expand with heat. This particularly applies to heating and chilled water pipelines which are constantly exposed to tem-perature variations with the changes in ambient temperatures. Appropriate pipe supports should be selected which are able to swing or slide thus preventing a build up in tensile forces.

Example 1 :Copper tube (Cu) length of pipe run 30mDifference in temperature Δt (pipe temperature minus ambient air temperature) 50ºCPipe expansion 26mm

Note: In the case of plastic pipes in the above chart (PE, PP and PVC) the linear expansion reading has to be multiplied by a factor of 10

Example 2 :PVC pipe length of pipe run 40mDifference in temperature Δt (pipe temperature minus ambient air temperature) 40ºCPipe expansion 13mm x 10 = 130mm

Kwik-Smart 49

Plumbing Copper TubeTubeNominalSize

PipeO.D.

Pipe MassEmplykg/m

Pipe MassFull of Waterkg/m

MaximumSupport

Span

15 12.70 0.30 0.39 1.5020 19.00 0.52 0.75 1.5025 25.40 0.83 1.25 2.0032 31.80 1.05 1.72 2.5040 38.10 1.27 2.27 2.5050 51.20 1.70 3.57 3.0065 63.50 2.14 5.07 3.0080 76.20 3.42 7.60 3.00100 101.60 4.58 12.18 4.00150 152.40 8.58 25.86 4.00

PVC Soil / Strom Water PipePipeNominalSize

PipeO.D.

Pipe MassEmplykg/m


MaximumSupport

Span

40 43.10 0.41 1.55 1.0050 56.00 0.59 2.62 1.0065 69.10 0.89 4.02 1.2080 82.70 1.15 5.69 1.20100 110.40 1.30 9.70 1.20150 160.50 3.02 21.12 1.20225 250.70 7.35 51.21 3.00300 315.90 11.82 81.15 3.00

HDPE - PPR PipePipeNominalSize

PipeO.D.

Pipe MassEmplykg/m


Maximum Support Span

@ 20C

@80C

20 20.00 0.16 0.32 0.80 0.6025 25.00 0.24 0.49 0.85 0.7032 32.00 0.38 0.80 1.00 0.7040 40.00 0.61 1.27 1.10 0.8550 50.00 0.90 1.93 1.25 0.9063 63.00 1.44 3.09 1.40 1.0575 75.00 2.09 4.41 1.50 1.0590 90.00 2.98 6.34 1.65 1.15110 110.00 4.39 9.39 1.90 1.30

Refrigeration Copper TubeTubeNominalSize

PipeO.D.

Pipe MassEmplykg/m


MaximumSupport

Span

1/4” 6.35 0.14 0.16 1.003/8” 9.53 0.22 0.27 1.001/2” 12.70 0.30 0.39 1.505/8” 15.88 0.38 0.54 1.503/4” 19.05 0.46 0.69 1.507/8” 22.23 0.55 0.88 1.501 1/8” 28.58 0.71 1.27 2.001 3/8” 34.93 0.87 1.73 2.501 5/8” 42.75 1.03 2.35 2.502 1/8” 53.98 1.36 3.50 3.002 5/8” 66.68 2.25 5.55 3.00

Steel Pipe to Schedule 40PipeNominalSize

PipeO.D.

Pipe MassEmplykg/m


MaximumSupport

Span

15 21.30 1.26 2.00 2.0020 26.70 1.68 2.20 2.5025 33.40 2.50 3.00 3.0032 42.20 3.38 4.00 3.0040 48.30 4.05 4.90 3.5050 60.30 5.43 7.70 4.0065 76.00 8.62 12.00 4.5080 88.90 11.28 15.00 5.50100 114.30 16.06 25.00 6.00150 168.30 28.23 50.00 7.00200 219.10 42.49 74.00 8.50250 273.00 60.24 115.00 9.00300 323.90 73.76 150.00 10.00350 355.60 81.21 216.00 10.00400 406.40 93.13 264.00 10.50450 457.20 105.05 316.00 11.00500 508.00 116.97 272.00 12.00600 609.60 140.81 500.00 14.00

Pipe Size Details

PIPE SUPPORT

50

• KS135 Pipe Stands allow vertical adjustment of the supported pipe using the Lock Nut provided.When the desired height is achieved, the Lock Nut should be Welded to the lower Pipe.

• The height from the centre of the pipe to the underside of the base plate should be nominated at the time of order

• Standard Finish Hot Dip Galvanised.

• KS136 Pipe Stands allow vertical adjustment of the supported pipe using the Lock Nut provided.When the desired height is achieved, the Lock Nut should be Welded to the lower Pipe.

• The height from the centre of the pipe to the underside of the base plate should be nominated at the time of order

• Standard Finish Hot Dip Galvanised.

KS135 Pipe Stand

KS136 Pipe Stand

Kwik-Smart 51

• Smooth operating Slide Guide for ceiling, wall or Floor Mounting• Two Clamps prevents jamming and misalignment• Large sliding distance up to 60mm thermal expansion

• Smooth operating Slide Guide for ceiling, wall or Floor Mounting• Two Clamps prevents jamming and misalignment• Large sliding distance up to 125mm thermal expansion

• Low minimum height - only 25mm• Variable height - height is governed by thread length• Ideal for use with Binder-Strut Channels• Available suitable for both M10 and M12 threads

• Variable height - height is governed by thread length• Ideal for use with Binder-Strut Channels• Available in M16 thread

KS190 Light Duty Slide Guide

KS191 Heavy Duty Slide Guide

PIPE SUPPORT

PIPE SUPPORT

52

KS195 Noise Resilient Pad

KS196 Noise Resilient Washer

• Reduction of structure borne noise for numerous mounting situations• Ideally suited to insulate across and supports using Binder-Strut Channels• Protection Nozzel prevents metal contact between Threaded Rod/Bolts and Binder channels

• Highly elastic sound absorber for light compressive loads• Ideally suited to insulate across and supports using Binder-Strut Channels• Protection Nozzel prevents metal contact be tween Threaded Rod/Bolts and Binder channels

• Sound insulation average 17dB (A)• Ideally used with KS-196 for Binder Channels• Suitable for M10 Threaded Rod or Bolts

• Sound insulation average 18dB (A)• Ideally used with KS-195 for Binder Channels• Suitable for M10 Threaded Rod or Bolts

Kwik-Smart 53

the Binder pressure gauge adapter probe.

b) Lubricate the probe with a small amount of silicone oil and partially insert the pressure gauge adapter probe into the test plug. If you are not sure of the pressure behind the plug, be prepared to quickly with-draw the probe before rupturing or over-pressuring the gauge. The test plug, in its static state and without a cap can easily withstand over 3500 Kpa without leaking. Do not assume that since the plug is not leaking that it is safe to quickly and fully insert a low range pressure gauge. If you are wrong the low range gauge could explode in your hand.

c) When the pressure gauge needle stops moving up-scale fully insert the probe and read the pressure.

d) Do not leave the probe in the plug longer than necessary. Always screw the adapter probe union to the top of the test plug to prevent the internal pressure from ejecting the gauge and probe.

e) When removing the probe do not position your face near the plug. The plug should not leak when removing the probe but always observe safety precautions.

f) As soon as the probe is removed replace the test plug cap.

6. Temperature Probe Insertion

a) Temperature probe insertion is similar to the pressure probe inser-tion with the exception that the op-erator should always first determine the pressure behind the plug before insertion of the temperature probe. This establishes that the plug is op-erating within its specification limits. After pressure has been determined follow the steps outlined in 5a to 5f.

7. When using a test plug which has been installed and unused for sev-eral years follow all the procedures shown aboveSpecification: Body available in Denzincification resis-tant Brass Alloy or Type 316 Stain-less Steel Cores available in Nordel

Specification:

Body available in Denzincification resistant Brass Alloy or Type 316 Stainless Steel Cores available in Nordel for hydraulic installations or Neoprene for natural gas installa-tions.

Temperature Range -10ºC to +135ºC Maximum Pressure 3500Kpa Standard Plug Thread 1/4” BSP, available in 1/4” NPTNordel cores must not be used on natural gas installationsOperating Procedure for Pres-sure and Temperature Readings

1. The operator should wear protec-tive clothing i.e. gloves and goggles when using the plug in high tem-perature lines or where injurious liq-uids or gases are contained.

2. Slowly remove the cap from the plug, if whilst doing so you feel or hear gas or liquids escaping imme-diately retighten the cap. Determine at this time if the plug has been used improperly and if necessary replace the plug.

3. Having determined that the plug is operating correctly,remove the cap.

4. Select the appropriate probe for pressure or temperature.Clean and lubricate the probe with a small amount of silicone oil. Examine the probe for any sharp burrs which could cut the plug cores. Remove any burrs before using; do not use non-standard or damaged probes.

5. Pressure Probe Insertiona) Determine approximate pressure in the pipeline and select a 1∕4” BSP Male outlet pressure gauge of suit-able range and securely screw onto

Test Plug Test Plug Extension

for hydraulic installations or Neo-prene for natural gas installations.

Hydraulics Installations:

The test plug used in the hydraulics industries is the Twinlok Test Plug. It is normally the Dezincification resis-tant.Brass Alloy body with the Nor-del core.Chilled Water circuitsFan Coil UnitsPumpsHeating Water Heat Exchangers

Natural Gas Installations:

The test plug used in natural gas in-stallations is a“Pete’s Plug”.

It has the Dezincification resistant Brass Alloy body but must have the Neoprene Core.

Test Plug Identification

For ease of identification, the Twin-lok Test Plug uses a Red Cap Strap whereas the Pete’s Plug uses a Black Cap Strap.

Always Insist On Twinlok Test PlugsYour Absolute Guarantee of Leak Proof Plugs, 100% Dezincification Resistant.

Twinlok is the registered trade mark belonging to the Binder Group Pty Ltd.

®

®

TEst Plug specification

54

Description

1/4 BSP Twinlok Test Plug Brass

1/4 NTP Twinlok Plug Brass

1/4 BSP Pete’s Plug Brass DRB

1/4 NTP Pete’s Plug Brass

Description

Extension Hex 1/4 BSP Test

Extension Hex 1/4 BSP X 3/8 BSP X 65mmExtension Hex 3/8 BSPT X 3/8 BSPP X 65mm

Description

PG B100 0 to 100

PG B100 0 to 250

PG B100 0 to 400KPA

GP B100 0 to 1000KPA

Description

Dial test thermometer -30 to 70

Dial test thermometer -10 to 110Digital Stem thermometer -10 to 110

• Plugs and Extensions available in Stainless on request.



•Gauges and Thermometers available in other scales on request.

• Gauges and Thermometers available in other scales on request.

• Gauges and Thermometers available in other scales on request.

Twinlok Test Plug Brass [Z/P]

Hexagon Plug Extension [Z/P]

Pressure Gauge

Dial Test Thermometer

Adaptor Pressure Gauge Diiferetial Thermometer

Plug’s & gauge’s

BEAMCLAMP is a registered trademark of Access Technologies Limited, a subsidiary of Binder Group Pty Ltd. Whilst every effert has been made to ensure the accuracy of the information conatined in this leaflet Access Technologies Limited cannot be held responsible for any errors or omissions. Access Technologies Limited reserve the right to alter or withdraw products without prior notice. Access Technologies Limited accept no responsibility for any loss or damage arising from improper use of their products.© 2008 Access Technologies Limited. All Rights Reserved

•NO SPECIAL TOOLS OR SKILLED LABOUR REQUIRED•HOT DIP GALVANISED AS STANDARD

•NO WEAKENING OF EXISTING STRUCTURE •NO DAMAGE TO PROTECTIVE COATINGS

SAFE STEELWORK CONNECTIONS

Installation of lifting equipment Installation of a new runway beam for a crane

Hanging of industrial lighting systems Cable tray support to existing steelworksystems

BEAMCLAMP®

56

The Type BY clamp is designed for High Friction and Tensile applications that exceed the capacities of the standard Beam-Clamp® products. It features a recessed top that prevents the head of the bolt fromrotating during installation therefore requires the use of only one wrench. The Type BYP washer can be used to fill in the recess of the Type BY to provide a flat surface for a washer and nut. This also allows the Type BY clamps to be used together in beam to beam connec-tions. The full width tail of the BY allows for use with slotted holes and the Type BY may also be used in unison with other BeamClamp® products for greater diversity in applications.

Beam Clamp-BYP

Without-BYP

Product Table

Beam Clamp-BY

With -BYP

Product Code

Size Product Code

TailLength

A B C D1 D2 E Width Torque Tensile SWL(kN) per bolt (5:1 Factor of Safety)

FrictionalSWL (kN)

per two bolts Paint-

ed Steel(2:1 Factor of

Safety)

Bolt Dia (mm)

BYP-12 M12 BY-12S Short M12 27 28.9 13 23 5 12.5 40 90 10.60 4.29BYP-16 M16 BY-16S Short M16 33 33 17 30 8 15 49 240 17.29 8.02BYP-20 M20 BY-20S Short M20 39 39 22 37 10 18 55 470 29.58 11.94 BY-12M Medi-

um M12 27 28.5 13 23 5 12.5 40 130 11.65 7.88

BY-16M Medi-um

M16 33 33 17 30 8 15 49 300 19.41 15.50

BY-20M Medi-um

M20 39 39 22 37 10 18 55 647 32 23.76

• Hot Dip Galvanised to BS EN ISO 1461.• Manufactured from Ductile Iron to BS EN 1563.These products are independently tested in situations to simulate typical site conditions.

The Safe Working Loads are based on assemblies tested in typical conditions. Do not exceed the Safe Working Load (SWL) specified.

*Frictional failure for the Type BY clamp is 1mm slip from its original position. Frictional capacities are based on shot blast and painted steelwork. Due to variance in thickness of Hot Dip Galvanised coatings please contact Kee Safety for frictional capacities based on Hot Dip Galvanised steelwork. Independently tested at Ceram, Lloyds Register Certification applied for and pending.

The BY recess is suitable for the hexagonal head of standard grade 8.8 and 10.9 bolts. The Type BYP may be used to fill in the recess allowing for any grade bolt or nut to be tightened down to its surface

COMPONENTS TYPE BY & BYP

BEAMCLAMP®

Kwik-Smart 57

The range of packing pieces below are designed to provide support to the underside of type BY clamps to ensure they clamp at 90 degrees to the steel and provide a flatsurface for the bolt head or nut to be tightened down on to.These can be used in various combinations with the two taillengths of BY clamps to achieve the best clamping position.

The Type BY can be used in a variety of applications and our design team will be pleased to configure a connection specific to your requirements. A design sheet is available for manually working out of the tail length and packing piece combinations along with the bolt lengths and location plate dimensions and is available upon request.

BH2

Type BY used with Type BZ and Type BH

BF3 BF4

Typical end plate cantilevered connection supporting heavy duty work.

W-Beam to C-Channel using combination of BY and BZ clamps.

Two angles connected together using combination of BY and BZ clamps.

Product Code

A B C Ø D

(mm)BH2-14 2 40 40 14BH2-18 2 48 48 18BH2-21 2 50 50 21

Product Code

A B C Ø D

(mm)BF3-14 5 40 40 14BF3-18 5 50 52 18BF3-21 5 55 56 21

Product Code

A B C Ø D

(mm)BF4-14 10 40 40 14BF4-18 10 50 52 18BF4-21 10 55 56 21

PACKING PIECES FOR BY CLAMPS

BEAMCLAMP®

58

The type BA are commonly used in pairs to clamp two steelsections together. The type BA has a recessed top to grip the head of a grade 8.8 setscrew or bolt, this allows a nut and washer to be tightened down on to the flat top of the BB using one tool only. Both clamps are available with three tail lengths 1,2 or 3 (dim E), this should be as near to the thickness of steel it is clamping on or slightly less if an exact match is not possible. Packing pieces BF1, BG1 and BH1 can be used in combination with the tail length to achieve a match to the steel flange, please see page 18 for these items. BA and BB types are suitable for parallel flanges and flanges up to 8 degrees taper. They can also be used on their own if one piece of the steelwork has been pre-drilled. To simplify the selection of tail lengths and packing pieces please see the tables on pages 24 and 25. Please note when using tapered steelwork it is the edge of the steel that we require, see our tables on pages 34 and 35 for edge thickness dimensions.

Beam Clamp-BA

PARALLEL FLANGE INSTALLATION

TAPERED FLANGE INSTALLATION

Product TableProduct Code

Short

ProductCode

Medium

Product Code

Long

A B C D1 D2 E Width Torque Tensile SWL

(kN) per bolt (5:1 Factor of Safety)

FrictionalSWL (kN)

per two bolts

Painted Steel(2:1 Factor of

Safety)

Bolt Dia (mm)

(Nm)

BA-08M M08 9 16 5 9 / 4 / 20 6 1.25 /

BA-10S BA-10M BA-10L M10 12 20 6 11 4 5 7 26 20 2.5 /

BA-12S BA-12M BA-12L M12 15 25.5 7 13 4.5 6 9.5 29.5 70 5.75 1.3

BA-16S BA-16M BA-16L M16 17 31 9 17 5.5 8 11 36 150 9.87 3.9BA-20S BA-20M BA-20L M20 21 35 11 21 7 10 12.5 44 290 16.47 11

BA-24S BA-24M BA-24L M24 26 49 13 25 9 12 16 53 490 21.1 18

• Hot Dip Galvanised to BS EN ISO 1461.• Manufactured from Ductile Iron to BS EN 1563.• 5 to 1 Factor of Safety• Lioyds Register approved• DIBt approved


COMPONENTS TYPE BA

BEAMCLAMP®

Kwik-Smart 59

The type BB are commonly used in pairs to clamp two steelsections together. The type BA has a recessed top to grip the head of a grade 8.8 setscrew or bolt, this allows a nut and washer to be tightened down on to the flat top of the BB using one tool only. Both clamps are available with three tail lengths 1,2 or 3 (dim E), this should be as near to the thickness of steel it is clamping on or slightly less if an exact match is not possible. Packing pieces BF1, BG1 and BH1 can be used in combination with the tail length to achieve a match to the steel flange, please see page 18 for these items. BA and BB types are suitable for parallel flanges and flanges up to 8 degrees taper. They can also be used on their own if one piece of the steelwork has been pre-drilled. To simplify the selection of tail lengths and packing pieces please see the tables on pages 24 and 25. Please note when using tapered steelwork it is the edge of the steel that we require, see our tables on pages 34 and 35 for edge thickness dimensions.

Beam Clamp-BB



Product Code

Short

ProductCode

Medium

Product Code

Long



FrictionalSWL (kN)per two bolts Painted Steel(2:1 Factor of Safety)

Bolt Dia (mm)

(Nm)

BB-08M M08 9 16 5 9 / 4 / 20 6 1.25 /

BB-10S BB-10M BB-10L M10 12 20 6 11 4 5 7 26 20 2.5 /

BB-12S BB-12M BB-12L M12 15 25.5 7 13 4.5 6 9.5 29.5 70 5.75 1.3

BB-16S BB-16M BB-16L M16 17 31 9 17 5.5 8 11 36 150 9.87 3.9BB-20S BB-20M BB-20L M20 21 35 11 21 7 10 12.5 44 290 16.47 11BB-24S BB-24M BB-24L M24 26 49 13 25 9 12 16 53 490 21.1 18


Product Table


COMPONENTS TYPE BB

BEAMCLAMP®

60

The types BT and BW are specifically designed with a 10 de-grees sloping nose. This sloping nose makes them ideal for fixing on to tapered steelwork such as RSJ’s or crane rail sec-tions. The type BT has a recessed top to captivate the head of a grade 8.8 setscrew or bolt, the type BW has a flat top to allow a nut and washer to be tightened down on it. Both clamps are available with two tail lengths 1 or 2 (dim E), this should be as near to the thickness of steel it is clamping to or slightly less if an exact match is not possible. Packing pieces BF1, BG1 and BH1 can be used in combination with the tail length to achieve a match to the steel flange, please see page 18 for these items. The types BT and BW can also be used on their own if one piece of the steelwork has been pre-drilled. To simplify the selection of tail lengths and packing pieces please see tables on pages 24 and 25. Please note when using ta-pered steelwork it is the edge of the steel that we require, see our tables on pages 34 and 35 for edge thickness dimensions

Type BW

Type BT

PARALLEL FLANGE TAPERED FLANGE


BT

ProductCode

BW




Bolt Dia (mm)

(Nm)

BT-12 BW-12 M12 15 25.5 7 13 4 6 28.5 70 5.75 1.3BT-16 BW-16 M16 17 31 9 17 6 8 36 150 9.87 3.9BT-20 BW-20 M20 21 35 11 21 7 10 44 290 16.47 11

• Hot Dip Galvanised to BS EN ISO 1461• Manufactured from Ductile Iron to BS EN1563• 5 to 1 Factor of Safety• 10 degrees nose


COMPONENTS TYPE BT & BW

BEAMCLAMP®

Kwik-Smart 61

The BK1 is a self adjusting fixing that consists of two parts. The main body provides a recess to allow a hemispherical washer to be seated. This allows the body to adjust between a specified clamping range and as the washer rotates it pro-vides a flat surface for a nut. This mechanism makes the product suitable for clamping to tapered steelwork of up to 15 degrees, it is also extremely useful for projectswhere the thickness of steel may vary. The M08, M10 and M12 versions feature a tab at the back edge that can be located in the open ends of strut products, both aiding installation and preventing rotation once installed. Should the maximum clamping range be exceeded our BF2 and BG2 packers can be used to in-crease it, please see page 18 for detailsM16, M20, M24

M08, M10. M12

Product Table

Product Code

A B1 B2 C D Width Torque Tensile SWL



Bolt Dia (mm)

(Nm)

BK1-08 M08 3 to 12 3 to 9 42 14 41 6 0.26 /BK1-10 M10 3 to 15 3 to 12 54 21 41 20 0.58 /BK1-12 M12 3 to 18 3 to 15 48 17 41 70 2.03 /BK1-16 M16 3 to 24 N/A 61 22.5 47 150 4.28 /BK1-20 M20 3 to 30 N/A 73 26 58 290 6.77 /BK1-24 M24 3 to 36 N/A 86 37.5 79 490 7.52 /



COMPONENTS TYPE BK1

BEAMCLAMP®

62


The BE1 and BE2 feature a socket screw at the back to provideadjustment for varying steel thicknesses. They are the ideal choicewhen flange thicknesses are unknown or change on a project asthey eliminate the need for packing pieces up to their maximumadjustment (Dim E). Once this maximum is exceeded our BF2 andBG2 packers can be used to increase the clamping range, pleasesee page 18 for details. To make the selection of tail lengths andpacking pieces easy please see tables on pages 24 and 25. Pleasenote the BE1 and BE2 are not suitable for steel flanges with tapersgreater than 5 degrees.

Beam Clamp - BE1

Beam Clamp - BE2

Product Table

• Hot Dip Galvanised to BS EN ISO 1461.• Manufactured from Ductile Iron to BS EN 1563.• 5 to 1 Factor of Safety• Lioyds Register approved•Socket screw adjustment



Product Code

BE1

ProductCode

BE2

A B C D1 D2 E F Width Torque Tensile SWL(kN)

per bolt (5:1 Factor of Safety)


Bolt Dia

(Grade 8.8)

(mm)(Nm)

BE1-10 M10 20 20 6 / 5 to 20 M06 26 20 2.5 /BE1-12 BE2-12 M12 26 25.5 7 13 6 to 22 M08 28.5 70 3.72 1.3

BE1-16 BE2-16 M16 30 31 9 17 7 to 23 M08 36 150 8.25 3.9BE1-20 M20 35 34 11 / 8 to 24 M10 44 290 16.12 11BE1-24 M24 49 49 13 / 10 to 30 M12 53 490 21.1 18

COMPONENTS TYPE BE1 & BE2

BEAMCLAMP®

Kwik-Smart 63

The types BC1 and BD1 are designed to hook over the up-standing flanges of angles or channels. They can be used together for channel to channel connections or in conjunction with our other clamping products for making angle/channel connections to other types of steel. The BC1 features a re-cessed top to grip a bolt head and theBD1 has a flat top to allow a nut and washer to be tightened on to it. It is suitable for use with studding or other threaded items but we always recommend the use of grade 8.8 high tensile threadeditems.

Beam Clamp - BC1

Beam Clamp - BD1

FLANGE CONTACTINGON BOTTOM EDGEOF TYPE BC1 OR BD1

FLANGE CONTACTING ONRIB OF TYPE BC1 OR BD1

Product Table

• Hot Dip Galvanised to BS EN ISO 1461.• Manufactured from Ductile Iron to BS EN 1563.• 5 to 1 Factor of Safety• Lioyds Register approved•Socket screw adjustment

Product Code

BC1

Produc Code

BD1

A B C D1 E F Width Torque Tensile SWL(kN)

per bolt (5:1 Factor of Safety)

Bolt Dia(Grade 8.8)

(mm)(Nm)

BC1-08 BD1-08 M08 9 8.5 6 5 9 22 3 1.25BC1-10 BD1-10 M10 12 10.5 7.5 6 11 29 10 2.5

BC1-12 BD1-12 M12 15 13.5 9.5 7 12 31.5 35 4.32BC1-16 BD1-16 M16 17 14 11.5 9 17 41 75 7.5BC1-20 BD1-20 M20 21 15 13.5 11 21 49.5 145 11BC1-24 BD1-24 M24 26 19 17 13 25 60 245 17.17


COMPONENTS TYPE BC1 & BD1

BEAMCLAMP®

64

Our range of packing pieces is designed to provide sup-port to the underside of clamps to ensure they clamp on to the steel at the correct angle. We have a series of short packers designed for the BA, BB, BT and BW clamps and a long series for the BE1, BE2 and BK1 clamps that reach further back on to the supporting steel. The packers can be used in combination with the fixing range of the clampto ensure a correct fixing. See tables on pages 24 & 25 for the correct combinations for different steel thicknesses.

Type BH1

Type BF2

Type BF1

Type BG2

Type BG1

Product Code

Boltdia.

A B C Ø D

(mm)BH1-08 M08 2 15 22 10BH1-10 M10 2 20 28 12BH1-12 M12 2.5 24 31 14BH1-16 M16 3 29 38 18BH1-20 M20 4 33 44 21BH1-24 M24 4 45 55 26

Product Code

Boltdia.

A B C Ø D

(mm)BF2-08 M08 4 2 22 10BF2-10 M10 5 30 28 12BF2-12 M12 6 39 30 14BF2-16 M16 8 49 35 18BF2-20 M20 10 58 43 21BF2-24 M24 12 77 55 26

Product Code

Boltdia.

A B C Ø D

(mm)BF1-08 M08 8 14 22 10BF1-10 M10 10 18 28 12BF1-12 M12 12 22 30 14BF1-16 M16 16 29 35 18BF1-20 M20 20 33 43 21BF1-24 M24 24 45 55 26

Product Code

Boltdia.

A B C Ø D

(mm)BG2-08 M08 8 24 22 10BG2-10 M10 10 30 28 12BG2-12 M12 12 39 30 14BG2-16 M16 16 49 35 18BG2-20 M20 20 58 43 21BG2-24 M24 24 77 55 26

Product Code

Boltdia.

A B C Ø D

(mm)BG1-08 M08 4 14 22 10BG1-10 M10 5 18 28 12BG1-12 M12 6 22 30 14BG1-16 M16 8 29 35 18BG1-20 M20 10 33 43 21BG1-24 M24 12 45 55 26

The recess in the BF1/ BF2 and BG1/ BG2 should always be face down-wards leaving a flat surface for the tail of the BeamClamp fix-ing to sit on as shown.

The type BF1/ BF2 and BG1/ BG2 should be slipped onto the bolt shank with the open end to-wards the steel-work flange as shown.

PACKING PIECES

BEAMCLAMP®

Kwik-Smart 65

The BL is used for clamping steelwork directly together with-out the need for a location plate. Typical applications would be clamping two steel sections of the same width running par-allel or for clamping down pressure vessel lids. It can also be used with clips and brackets underneath the nut and washer side for fixing conduit or even pipe work. The fixing is tested for tensile and lateral loads, please see data sheet below. The BL part is specifically designed to grip the head of a bolt or nut which means the clamp can always be fixed just using one spanner. The central bolt can be replaced with other threaded items such as threaded bar, eyebolts or J-bolts to provide a suspension element.• Only requires one tool for installation• Hot Dip Galvanised to BS EN ISO 1461• Extensive fixing range• Can accomodate clips/brackets• Tested for Tensile and Lateral Loading

Product Code

A B C D TighteningTorque

3 to 1 FActor of safety applied Tensile Load in line with

rod (kN)

Tensile Load at nose (kN)

(per pair)

Lateral Load (kn)

(mm)(Nm)

BL-08 12.5 45 40 5 to 20 10 1.0 7.4 0.25BL-10 14 58 47 6 to 30 20 2.5 9.3 0.40

BL-12 15 65 51.5 7 to 35 40 5.0 11.0 0.60BL-16 20 95 58 8 to 55 90 7.5 20.3 0.70BL-20 23 116 66 8.5 to 70 180 9.0 23.3 0.75BL-24 26 147 75 9 to 95 200 10.5 34.3 0.80

Tensile Load in line with threaded element

Loading Instruction

Tensile Load acting at the nose of the clamps

Lateral Load

Type BL


Product Table

BL FLANGE CLAMP

BEAMCLAMP®

66

THE GRATEFIX is a heavy-duty fixing that allows open floor grating to be fixed to the supporting steelwork from the top-side only. The Gratefix features a cast bottom piece that pro-vides additional strength to clamp on to the steelwork flange. The Gratefix is available in several different styles to suit the grating dimensions and the application. A mechanical galvan-ised M10 version is available with a symmetrical top bracket to suit 30mm ctrs grating or with an offset bracket to suit 30-41mm ctrs grating most commonly found in the UK. The M08 version is also available in grade 304 stainless steel with a topbracket to suit 30mm ctrs.

OPTION 2Pressed Top bracket – Material: Mild steel to EN 10025 grade S275Cast Bottom Bracket – Material: Malleable iron to BS 1562:Grade EN-GJMB-300-06Both finished in: Mechanical Galv to ASTM B695

OPTION 1Pressed Top Bracket – Stainless Steel to EN 10088 Grade 1.4301 (AISI 304)Cast Bottom Bracket – Stainless Steel to ASTM A743 Grade CF-8 (S30400).

• Allows easy repositioning or lifting of grating• No special tools or skilled labour required• No access to the underside required• Tested for vibration conditions at TÜV

• Mechanical Galvanised Malleable Iron• Stainless Steel Grade 304• Easily installed from the top side only• No drilling, no tapping or welding required

Installation

Step 1 Step 2 Step 3

Product Code

Material /Finish

Screwdia

To suit Grating bar centers (mm)

To suit Grating bar depths (mm)

Tightening torque (Nm)

GF-01 Option 1 M08 30 50 8GF-02 Option 2 M10 30 to 41 50 5

GRATE FIX

BEAMCLAMP®

Kwik-Smart 67

THE GRATING CLIP is the most common style of clip used for fixing down open steel flooring in the UK. It provides a quick and cost effective method of fixing. It is Hot Dip Galvanised and comes as standard with a top bracket to suit 30-41mm ctrs grating bars.

As previously mentioned the Floorfix HT and Gratefix have been tested in conditions to simulate the typical applications of these fixings. The fixings were tested for performance in both vertical and horizontal axis to ensure they did not work loose when subjected to vibration conditions. The test set-up can be seen below, the certificates are available on request.

Product Code

Screwdia

To suit Grating bar centers

(mm)

To suit Grat-ing bar depths

(mm)GRAT-08 M08 30 41 50

Industrial Testing

Horizontal Axis Test Vertical Axis Test

GRATING CLIP

BEAMCLAMP®

68

THE FLOORFIX HT has been developed following customer feedback to provide a fixing with increased functionality to suit a wider range of applications. Floorfix HT is designed to fix flooring plate to supporting steelwork from the topside only without the need for time consuming on site drilling, tapping, bolting or welding. It works on a cam mechanism that can be operated using a basic hexagon key drive. Floorfix HT is so named because it allows steel erectors a high degree of tolerance, it retains all the benefits of our widely renowned original design but is far more user friendly. FloorfixHT allows for floor plates to be fixed to new steelwork that is erected within +/- 6mm of its intended position. It is capable of fixing to steel flanges from 3 to 25mm without the need for additional packing pieces.

The FloorFix is designed for securing chequer/durbar plate to the supporting steelwork without the need for on site drill-ing or welding of the floor plate and supporting steel struc-ture. It allows the connection to be made from the top side only using a basic allen key wrench. It can be easily lifted for maintainence purposes and re-set to its original position within minutes. The FloorFix solution can be used anywhere without the need for specialist drilling/welding equipment or the need for expensive access equipment to get to the under-side. The FloorFix is also tested at TUV for vibration condi-tions and providing the countersunk screw is tightened to our recommended torque then the connection is guaranteed not to come loose.

• Allows easy repositioning or lifting of floor plate• No special tools or skilled labour required• No access to the underside required• Tested for vibration conditions at TUV

• Allows for +/- 6mm construction tolerance• Can fix up to 25mm thick steel as standard• Hot Dip Galvanised finish as standard• Easily installed from the top side only• No drilling, no tapping or welding required

• Installation from one side only• Manufactured from Ductile Iron• Hot Dip Galvanized• Allows for easy maintenance• Tested at TUV for vibration conditions

Product Code

Screwdia

Floor Plate Thickness Steelwork Flange Thickness Tightening torque (Nm)

FF-08HT M08 3 12 3 25 20FF-10HT M10 5 12 3 25 25FF-12HT M12 6 12 3 25 30

Product Code

Screwdia

Floor Plate Thickness Steelwork Flange Thickness Tightening torque (Nm)

FF-08 M08 3 12 3 15 20FF-10 M10 5 12 3 15 20FF-12 M12 6 12 3 15 30

Min

Min

Min

Min

Max

Max

Max

Max

Floorfix HT has been tested for vibration conditions to simu-late the most common applications where the fixings would be used e.g. walkways, machine shops and press shops. Please ask our technical department for a copy of the certifi-cate should you require this.

STEEL FLOOR FIXINGS

THE FLOORFIX HT

FLOORFIX

BEAMCLAMP®

Kwik-Smart 69

Step 1 :Assemble the Floor-fix HT to the unde side of the floor plate making sure the markings “THIS WAY UP” are facing it. Loosely tighten he bolt making sure the flat edge of the fixing is in line with the edge of the steel-work it is going to fix to.

Step 3 : Once the floor plate is in the desired position rotate the coun-tersunk bolt one full turn anti-clockwise.

Step 2 : Lower the plate in to position over the supportingsteelwork.

Step 4 : Tighten the coun-tersunk screw until the plate is secured, forguar-anteed performance use the recommended tight-ening torques given in table.

Installation Instruction

Plate Preparation

Floor Fix HT

Floor Fix HT

Floor Fix

Floor Fix

Steelwork Steelwork

Hole to be countersunk at 450 Hole to be countersunk at 450

Floor Plate Floor Plate

16.5 mm 15 mm

FLOORFIX HT INSTALLATION INSTRUCTIONS

BEAMCLAMP®

70

BoxBolt is a fully tested and approved blind connection solu-tion for connecting to hollow section steel or where access is restricted to one side only. The BoxBolt is suitable for use with rectangular, square and even circular hollow sections. The BoxBolt features a hexagon head design to aid installation with a standard wrench. It allows it to be installed with our unique BoxSokTM installation tool for when installation time needs to be kept to an absolute minimum.

The BoxBolt is available in three finishes; Zinc Plated for the less aggressive environments, Hot Dip Galvanized for the more aggressive environments, and Stainless Steel for the most demanding of applications. These finishes combined with three lengths of BoxBolt make it extremely flexible to suit its environment and application. The BoxBolt is approved for use by Lloyds Register (LR) type approval and the Deutsches Institut für Bautechnik (DIBt) to give the specifier and user total confidence.

The loads stated above are based on our DIBt (Deutsches Institut für Bautechnik) approval document Z-14.4-482. The loads shown above are working loads based on the rated loads factored by 1.4 which is an average value between 1.35 used for static loading and 1.5 used for live loads. The rated loads stated in our approval already have a 1.375 factor for tensilw and 1.1 factor for shear applied to them. This therefore means that the above loads have a 1.375 x 1.4 = 1.925 to 1 FOS in tensile and 1.1 x 1.4 = 1.54 FOS in shear.

The BoxBolt is also tested and approved by DIBt (Deutsches Institut fur Bautechnik) which complies with the DIN 18800 and Eurocode 3 design methods for bolted steel connections. A design guide and calculator is available when using these methods. Please ask our technical team for more information.The BoxBolt is also Lloyds Register type approved for use, should you required a copy of the approval certificate our techincal team will be able to assist. The strenth of the material ourBoxBolt is connecting into should be checked for structural capacity by a structural engineer.

Part Number and Description

Dimensional Information Technical Load Information

Box Bolt

Product code

Zinc

Product code

HDG

Size Setscrewlength(mm)

Fixing range(dim x)

Across flats of shoul-der(mm)

shoulderthick-ness(mm)

Dim A

Dim B

Hole Size Tro-que

Galvanised/ Zinc plated Tensile Shear

Stainless SteelTensile Shear

M06 B06-1 B06-1H 1 45 3 29 17 30 11 11 +1.0,-0.25 19 5.71 16.21 / /

M08B08-1 B08-1H 1 50 3 28 22 35 13 14 +1.0,-0.25 25 12.86 21.07 13.29 26.14

B08-2 B08-2H 2 70 12 46 22 35 13 14 +1.0,-0.25 25 12.86 21.07 13.29 26.14

B08-3 B08-3H 3 90 24 66 22 35 13 14 +1.0,-0.25 25 12.86 21.07 13.29 26.14

M10B10-1 B10-1H 1 50 3 23 24 40 15 18+1.0,-0.25 45 24.07 37 21.07 47.07

B10-2 B10-2H 2 70 15 43 24 40 15 18+1.0,-0.25 45 24.07 37 21.07 47.07

B10-3 B10-3H 3 90 30 63 24 40 15 18+1.0,-0.25 45 24.07 37 21.07 47.07

M12B12-1 B12-1H 1 55 3 25 26 50 18 20+ 1.0,-0.25 80 29.43 48.29 30.64 59.88

B12-2 B12-2H 2 80 18 50 26 50 18 20+ 1.0,-0.25 80 29.43 48.29 30.64 59.88

B12-3 B12-3H 3 100 36 70 26 50 18 20+ 1.0,-0.25 80 29.43 48.29 30.64 59.88

M16B16-1 B16-1H 1 75 3 35 36 55 20 26+ 2.0,-0.25 190 52.29 88.21 57.07 108.57

B16-2 B16-2H 2 100 24 60 36 55 20 26+ 2.0,-0.25 190 52.29 88.21 57.07 108.57

B16-3 B16-3H 3 120 48 80 36 55 20 26+ 2.0,-0.25 190 52.29 88.21 57.07 108.57

M20B20-1 B20-1H 1 100 3 42 46 70 25 33 +2.0,-0.25 300 92 145.36 89.07 181.79

B20-2 B20-2H 2 120 30 72 46 70 25 33 +2.0,-0.25 300 92 145.36 89.07 181.79

B20-3 B20-3H 3 150 63 102 46 70 28 33 +2.0,-0.25 300 92 145.36 89.07 181.79

The above loads are working loads that have the following Factor of Safety (FOS) Applied: Tensile = 1.925 to 1 Shear = 1.54 to 1

BoxBolt

BoxBolt Technical Data

box bolt

BEAMCLAMP®

Kwik-Smart 71

Technical Information

BoxSok™ Rapid Assmebly Tool

or

Shoulder

Core Bolt

Button Head Socket

Hexagon Head

CountersunkSocket

Socket head cap screw

Body

Cone

Min. edgedistance

The BoxBolt is often used on high profile projects where the aesthetics of the building are essential. It is for this rea-son the BoxBolt can be adapted to suit the requirements of the Client and the Architect to make the connection pleas-ing to the eye. The most common versions we can offer are shown above. Should you require a different style then please contact our technical department.

MaterialsMild steel to BS EN 10083 Grade 1.1151Stainless steel to BS EN 10088 Grade 1.4401

FinishesZinc plated to BS EN 12329 : Class Fe//Zn8//AHot Dip Spun Galvanised to BS EN ISO 1461

The BoxSokTM Installation Tool is a unique rapid assembly tool for the BoxBolt fixing. This specially designed socket holds the hexagon shoulder on the body to stop it rotating whilst allowing the inner socket to tighten up the core bolt. The core bolt draws the cone up inside the slotted body of the sleeve and expands the individual fins inside the con-nection. The BoxSokTM eliminates the need for two tools to install the BoxBolt; this considerably speeds up the instal-lation process and also reduces the risk of trapping hands between two tools. The BoxSokTM device is available to suit all BoxBolt diameters.

box bolt

BEAMCLAMP®

72

Fast Fit is an off the shelf engineered clamping solution toconnect two steel sections together without the need for on-site drilling or welding. All you need to secure two sectionstogether comes in one box. The system comprises a framewhich wraps around the edges of the sections and slides intoplace to provide a position for the clamps to be secured.The system allows for varying angles that can be easilyachieved by sliding the beams relative to each other.The Fast Fit system delivers a guaranteed connection everytime without the need for on-site testing or relying on theskills of the installer. No removal of the protective coatingson the existing steel or holes is needed to make a connection.All that is required to complete a connection are simple handtools and semi-skilled labour


Boltdia

Boltgrade

Boltlength (mm)

Overallsize(mm)

Flangethickness

(mm)

Flangewidth

Tighteningtorque(Nm)

Tensile load(4 bolts)

(kN)

Frictional load(kN)

BCFF16 M16 8.8 130 350 x 350 3 to 27 65 to 190 150 21.19 5.08

• NO SITE DRILLING OR WELDING• NO HOT WORK PERMITS• NO FABRICATION OF PLATES OR CLAMPS

Achievable AnglesThe Fast Fit system is designed to allow sections of different widths to be connected at varying angles. The table below provides information on the angles which can be achieved.

Factor of SafetyThe below loading data has a 5 to 1 Factor of Safety.

mm 65 76.2 88.9 101.6 114.3 127.0 139.7 152.4 165.1 177.8 19065 45 45 50 50 50 55 55 60 65 70 7576.2 45 45 50 50 50 55 55 60 65 70 7588.9 50 50 50 50 55 55 55 55 65 70 75101.6 50 50 50 50 55 55 55 55 65 70 75114.3 50 50 50 50 50 55 55 55 65 70 75127.0 55 55 55 55 55 55 55 55 65 70 75139.7 55 55 55 55 55 55 55 55 65 70 75152.4 60 60 60 60 60 60 60 65 65 70 75165.1 65 65 65 65 65 65 65 65 65 70 75177.8 707 70 70 70 70 70 70 70 70 75 75190 75 75 75 75 75 75 75 75 75 75 80

Top Section Flange Width

Bot

tom

Sec

tion

Flan

ge W

idth

FAST FIT

BEAMCLAMP®

Kwik-Smart 73

Installation Instructions

The Fast Fit system can be fully installed in under 5 minutes which saves time compared to traditional welding or drilling methods. Following the steps below will give a fully guaranteed connection.

STEP 1 - Install the framework of platesaround the two sections to be connected.

STEP 4 - The front and back edge of theclamps should run parallel with the steelsections.

STEP 5 - Hold the head of the bolt with astandard wrench and tighten the nut with a torque wrench to the recommended torque stated above. Repeat this for all four bolts.

IMPORTANT CHECK!Always check the clamps have been installed the correct way around. See diagrams below:

STEP 2 - Rotate the open side of the platearound the sections so that the frame is complete.

STEP 3 - Insert one set of clamps througheach corner ensuring they are positioned as in step 4.

Fast Fit System vs. Drilling or Welding – ComparisonThe table below demonstrate the time that can be saved by using a Fast Fit system compared to either a standard welded or drilled and bolted connection. The majority of time and cost is saved by the reduction in preparation and labour time.This table does not include the potential for remedy work that may need to be carried out should the connection not be in the correct place. With the Fast Fit system this is quick and easy to do where as with a welded or drilled and bolted connection it is more difficult and time consuming.

Connection Requirements Time (hrs) Details of each stepEngineering 0.1 The design time is reduced dramatically as the system

works with stated parametersMarking of Steel 0.05 The marking is reduced as the connection is adjustableSite set up 0.05 Product arrives in a kit ready to installAssenbly time 0.05 The assembly time is quicker than a bolted connection as

no hole alignment is requiredTightening of bolts 0.04 Allowing 1 minute per bolt and nut

Fast Fit Work System

Time taken by each systemWelding

(hrs)Drilling & Bolting

Fast Fit(hrs)

Savings(hrs)

4.5 3.5 0.5 3 to 4

FAST FIt

Index

74

Part ID Description Binder Code

Page No.

BC1-08 M08 Hook Type - Recess Top Beam Clamp 362001 63







Page No.

BD1-08 M08 Hook Type - FlatTop Beam Clamp 363001 63

BD1-10 M10 Hook Type - Flat Top Beam Clamp 363002 63






Page No.

BE1-10 M10 Adjustable Recess Top Beam Clamp 364001 62






Page No.

BE2-12 M12 Adjustable Flat Top Beam Clamp 365001 62

BE2-16 M16 Adjustable Flat Top Beam Clamp 365002 62

BC1 - Beam Clamp

BD1 - Beam Clamp

BE1 - Beam Clamp

BE2 - Beam Clamp


Page No.

BA-08M M08 Recessed Top Beam Clamp - Med 360001 58

BA-10S M10 Recessed Top Beam Clamp - Short 360002 58


BA-10L M10 Recessed Top Beam Clamp - Long 360004 58

BA-12S M12 Recessed Top Beam Clamp - Shor 360005 58












BA - Beam Clamp

B

BB - Beam ClampPart ID Description Binder

CodePage

No.BB-08M M08 Flat Top Beam Clamp - Medium 361001 61

BB-10S M10 Flat Top Beam Clamp - Short 361002 61

BB-10M M10 Flat Top Beam Clamp - Medium 361003 61

BB-10L M10 Flat Top Beam Clamp - Long 361004 61











BB-S4M M24 Flat Top Beam Clamp - Medium 361015 61



Page No.

KS1796 Beam Clamp HDG 672034 25



KS1386 Beam Clamp ZP 674036 25

KS1271-SS Beam Clamp G316 S/S 673034 25


Beam Clamps


Page No.

BF1-08 M08 Middle Packer - Short 372001 64







Page No.

BF2-08 M08 Middle Packer - Long 372007 64






BF1 - Beam Clamp

BF2 - Beam Clamp


Page No.

BF4-14 M12 High Friction Washer P2 378008 57




Page No.




BF4 - Beam Clamp

BF3 - Beam Clamp

index

Kwik-Smart 75


Page No.

BG1-08 M08 Thick Packer - Short 373001 64







Page No.

BG2-08 M08 Thick Packer - Long 373007 64






BG1 - Beam Clamp

BG2 - Beam Clamp


Page No.

BH1-08 M08 Thin Packer ZP 371001 64






BH1 - Beam Clamp


Page No.

BK1-08 M08 Self Adjusting Beam Clamp 366001 61






BK1 - Beam Clamp


Page No.

BH2-14 M12 High Friction Washer Clipped 378014 57



BH2 - Beam Clamp


Page No.

BL-08 M08 BL Flange Clamp 377001 65






BL - Beam Clamp


Page No.

BT-12 BG379 M12 BT BeamClamp 379000 60




Page No.

BW-12 BG379 M12 BW BeamClamp 379003 60



BT Type - Beam Clamp

BW Type - Beam Clamp


Page No.

BY-16S M16 High Friction Clamp Short 378000 56

BY-20S M20 High Friction Clamp Short 378001 56

BY-12M M12 High Friction Clamp Medium 378002 56

BY-12S BG378 M12 High Friction Clamp Short 378017 56




Page No.

BYP-12 M12 High Friction Clamp Washer 378005 56



BY - Beam Clamp

BYP - Beam Clamp


Page No.

BG367-08 M08 BoxSok Installation Tool 367001 71





BoxSox - Beam Clamp


Page No.

B08-1 M08 BoxBolt Size 1 Zinc 368001 70















B08-1H M08 BoxBolt Size 1 HDG 368016 70











Box Bolt - Beam Clamp

Index

76


Page No.

BG106-15 15NB Light Duty Saddle Clamp HDG 106000 42







BG106 - Saddle Clamp


Page No.

BG100-15 15NB Light Duty 2 Bolt Clamp HDG 100001 40






















BG100-20-SS 20NB Light Duty 2 Bolt Clamp 316 100052 40












BG100-40CU-SS 40Cu Light Duty 2 Bolt Clamp 316 100115 40






BG100-15CU 15CU Light Duty 2 Bolt Clamp HDG 100200 40














BG100 - Light Duty 2 Bolt Clamp

BG100-40P 40PVC Light Duty 2 Bolt Clamp HDG 100300 40











Page No.

BG105-15 15NB Saddle Guide HDG 105000 41



















BG105-15CU 15Cu Saddle Guide HDG 105100 41













BG105-50P 50PVC Saddle Guide HDG 105201 41





BG105 - Saddle Guide





index

Kwik-Smart 77

BG107 - U Bolt ClampPart ID Description Binder

CodePage

No.BG107CON-20 20mm Conduit U-Bolt Clamp ZP 107000 43

BG107CON-25 25mm Conduit U-Bolt Clamp ZP 107001 43




BG107CON-20-H 20mm Conduit U-Bolt Clamp HDG 107011 43





BG107CON-20-SS 20mm Conduit U-Bolt Clamp Gr.316 107005 43





C


Page No.

UC150 150mm Unbraced Cantilever HDG 620001 21




UC750 750mm Unbraced Cantilever HDG 21

UC150-SS 150mm Unbraced Cantilever 316 SS 621001 21






Page No.

BC150 150mm Braced Cantilever HDG 21

BC300 300mm Braced Cantilever HDG 620005 21



BC750 750mm Braced UltraStrut Cantilever HDG 620008 21

BC150-SS 150mm Braced Cantilever 316 SS 21

BC300-SS 300mm Braced Cantilever 316 SS 621006 21





Page No.

UC150-KIT 150mm Unbraced Cantilever Kit HDG 21

UC300-KIT 300mm Unbraced Cantilever Kit HDG 622001 21



UC750-KIT 750mm Unbraced Cantilever Kit HDG 21

BC150-KIT 150mm Braced Cantilever Kit HDG 21

BC300-KIT 300mm Braced Cantilever Kit HDG 622004 21



BC750-KIT 750mm Braced U/Strut Cantilever Kit HDG 622007 21

Cantilever - Unbraced

Cantilever - Braced

Cantilever Kit


Page No.

BSC-1/4 1/4in Binsulclamp ZP 630000 36






BSC-1 1/8 1 1/8in Binsulclamp ZP 630006 36



BSC- 2 1/8 2 1/8in Binsulclamp ZP 630009 36





Binsul Clamp


Page No.

KS2600 Strip Isolation Barrier B2600 680000 47

KS1184 Strip Closure 3Mtr PVC B1184/PL 680002 47

Binder Strip Tape














BG106-15CU 15CU Light Duty Saddle Clamp HDG 106100 42














BG106-42P 42PVC Light Duty Saddle Clamp HDG 106200 42










BG106-300-SS 300NB Light Duty Saddle Clamp S/S 106314 42

Index

78

Channels-Kwik-Smart

Channels-Ultrastrut


Page No.

KS1000 41 x 41 x 2.5mm GB 610009 09

KS1001 41 x 82 x 2.5mm GB 610017 13

KS1000T 41x41x 2.5mm Slotted GB 610013 09

KS2000 41 x 41 x 1.5mm GB 610010 14

KS2000T 41 x 41 x 1.5mm Slotted GB 14

KS3300 41 x 21 x 2.5mm GB 610011 11

KS3300T 41x21x 2.5mm Slotted GB 610018 11

KS4000 41 x 21 x 1.5mm GB 610012 15

KS4000T 41 x 21 x 1.5mm Slotted GB 15

KS1000-H 41 x 41 x 2.5mm HDG 610000 09

KS1001-H 41 x 82 x 2.5mm HDG 6M Ln 610001 13

KS3300-H 41 x 21 x 2.5mm HDG 610002 13

KS3301-H 41 x 43 x 2.5mm HDG 610003 13

KS5500-H 41 x 62 x 2.5mm HDG 610004 16

KS1000T-H 41x41x 2.5mm Slotted HDG 610005 09

KS3300T-H 41x21x 2.5mm Slotted HDG 610006 11

KS1000-SS 41 x 41 x 2.5mm 316SS 610007 09

KS3300-SS 41 x 21 x 2.5mm SS 610008 11

KS1000-M 41 x 41 x 2.5mm Mill 610014 09

KS2000-M 41 x 41 x 1.5mm Mill 610015 14

KS3300-M 41 x 21 x 2.5mm Mill 610016 11

KS1000CI Concrete Insert HDG 610019 17


Page No.

US1000 41 x 41 Channel GB 610038 08

US1000T 41 x 41 Channel Slotted GB 610039 08

US3300 41 x 21 Channel GB 610040 10

US3300T 41 x 21Channel Slotted GB 610041 10

US1000-H 41 x 41 Channel HDG 610020 08

US1000T-H 41 x 41 Channel Slotted HDG 610021 08

US3300-H 41 x 21 Channel HDG 610022 10

US3300T-H 41 x 21 Channel Slotted HDG 610023 10

US1001-H 41x 82 Channel HDG 610028 12

US3301-H 41x 42 Channel HDG 610030 12

US1000-SS 41 x 41 Channel S/S 610024 08

US1000T-SS 41 x 41 Channel Slotted S/S 610025 08

US3300-SS 41 x 21 Channel S/S 610026 10

US3300T-SS 41 x 21 Channel Slotted S/S 610027 10

US1001-SS 41x 82 Channel S/S 610029 12

US3301-SS 41x 42 Channel S/S 610031 12

US1000T-M Channel Slotted Mill 610032 08

US3300T-M Channel Slotted Mill 610033 08

US1001-M 41x 82 Channel Mill 610034 12

US3301-M 41x 42 Channel Mill 610035 12

US1000-M 41 x 41 Channel Mill 610036 10

US3300-M 41 x 21 Channel Mill 610037 10

Channel ClipsPart ID Description Binder

CodePage

No.KS2024 8mm Channel Clip ZP 600100 34

KS2025 11mm Channel Clip ZP 600101 34



















































KS2070-62 159mm Channel Clip ZP 600152 34









Page No.

KS2072A Channel Base Fitting ZP 674030 24

KS2072B Channel Base Fitting ZP 674031 24

KS2073H Channel Base Fitting ZP 674032 24

KS2072A-H Channel Base Fitting HDG 672030 24

KS2072B-H Channel Base Fitting HDG 672031 24

KS2073H-H Channel Base Fitting HDG 672032 24

KS2072A-SS Channel Base Fitting G316 S/S 673030 24

KS2072B-SS Channel Base Fitting G316 S/S 673031 24

KS2072H-SS Channel Base Fitting G316 S/S 673032 24

Channel Base Fittings

index

Kwik-Smart 79

Channel Clip Copper Part ID Description Binder

CodePage

No.CCC-15 15Cu Channel Clip Powder Coated Brown 600500 35

CCC-20 20Cu Channel Clip Powder Coated Brown 600501 35











KS2070-76-H 197mm Channel Clip HDG 600758 34






KS2024-SS 8mm Channel Clip SS 600200 34

































KS2070-62-SS 159mm Channel Clip SS 600252 34








KS2024-H 8mm Channel Clip HDG 600700 34


















































HS2069-H 149mm Channel Clip HDG 600750 34



HS2070-64-H 165mm Channel Clip HDG 600753 34





Index

80

Channel Clip PVC

Channel Clip Pressure

Channel Clip - Press Pipe Clip


Page No.

CCP-40 40PVC Channel Clip Powder Coated White 600600 35











Page No.

PCP-15 15PVC Pressure Channel Clip PC White 600610 36










Page No.

KS109-40 Press Pipe Clip Powder Coated 600400 38









Page No.

KS 2240 End Cap (for KS1000) Grey PVC 680003 16

KS4240 End Cap (for KS3300) Grey PVC 680004 16

KS2240-W End Cap (for KS1000) White PVC 680005 16

KS680001 Bindersil Tape - Seal 50mm x 10m / Roll 680001 16

Channel End Cap


Page No.

KS2484 Channel Fitting ZP 672037 23










Channel Fittings




KS2577 Splice Plate ZP 672025 25


KS1026-H M10 Angle Cleat HDG 670102 23

KS1031-H Channel Fitting HDG 672000 23



























KS1031-SS Channel Fitting G316 S/S 673000 23
















Page No.

KS3006 M6 Channel Nut ZP 643000 31





KS3016 M6 Butterfly Nut ZP 643005 31

KS3007-H M08 Channel Nut HDG 644001 31




Channel Nut

index

Kwik-Smart 81


Page No.

FC-06 Flange Clamp M06 - D 374001 31

FC-08 Flange Clamp M08 - D 374002 31

FC-08 Flange Clamp M08 - T 374003 31

FC-10 Flange Clamp M10 - D (ZP) 374004 31

FC-12 Flange Clamp M12 - D (ZP) 374006 31


Page No.

KS4006 M6 Channel Spring Nut Short ZP 646000 31





KS3016 M6 Butterfly Nut ZP 643005 31





KS3006-SS M6 Channel Nut SS 645000 31



Channel Spring Nut Short


Page No.

KS1006 M6 Channel Spring Nut ZP 640000 31





KS1006-H M6 Channel Spring Nut HDG 641000 31





KS1007-SS M8 Channel Spring Nut SS 642001 31



Channel Spring Nut





Page No.

CH10 M10 Clevis Hanger HDG 670002 33

CH12 M12 Clevis Hanger HDG 670004 33

Clevis Hanger

D

F

G


Page No.

KS12-25 25HDPE Dual Clip 613100 37








KS12-110 110HDPE Dual Clip 613108 37

KS12-160 160H & 150PVC Dual Clip 613109 37

Dual Clip

Drop Anchor


Page No.

FF-08 M08 Floorfix Clip HDG 369001 68




Page No.

FF-08HT M08 Floorfix Clip HT HDG 369004 68



FF - Floorfix Clip

FF - Floorfix Clip HT


Page No.

FB40-P 40PVC Filbow Powder Coated White 616000 38








Filbow


Page No.

FW06-H M06 Flat Washer CS HDG 902525 31





FW06 M06 Flat Washer CS Zinc 902550 31





Flat Washer


Page No.

GRAT-08 Grating Clip 370001 67


Page No.

GF-02 Grating Fix 370003 66

Grating Clip

Grating FixPart ID Description Binder Code

Page No.

DIA0625 M6 X 25 Drop In Anchor ZP 909000 33


DIA1030 M10 X 30 Drop In Anchor ZP (Flanged) 909002 33




Flange Clamp

Index

82

H


Page No.

HB1080 M10 X 80 Hanger Bolt ZP 909100 32




Hanger Bolt


Page No.

HHS0620 M6 X 20 Hex Bolt Gr. 4.6 Zinc 900883 32





























HHS0612-H M6 X 12 Hex Bolt Gr. 4.6 HDG 900602 32



HHS0630-H M6 X 30 HEX BOLT Gr. 4.6 HDG 900606 32


















Hex Bolt

















HHS0620-SS M6 X 20 Hex Bolt SS 316 903034 32






























Page No.

HN06 M06 Hex Nut CL.8 Zinc 900100 32





HN06-H M06 Hex Nut CL.8 HDG 901530 32




Page No.

HC10 M10 Hex Connector Zinc 206015 33



Hex Connector

Hex Nut

index

Kwik-Smart 83





HN06-SS M06 Hex Nut CL.A4 (SS316) 901550 32





K

L

M

N

P


Page No.

KS10-15 15Cu 12-14 Kwik Clip 613200 37

KS10-20 20Cu 15-19 Kwik Clip 613201 37

KS10-25 25Cu 24-26 Kwik Clip 613202 37

KS10-32 32Cu 30-33 Kwik Clip 613203 37

KS10-40 40Cu & PVC Kwik Clip 613204 37

KS10-50 50Cu & PVC Kwik Clip 613205 37

KS10-65 65Cu 63-67 Kwik Clip 613206 37

KS10P-65 65PVC 70-73 Kwik Clip 613207 37

KS10-80 80Cu 74 - 80 Kwik Clip 613208 37

KS10-100 100Cu 101-106 Kwik Clip 613209 37

KS10P-100 100PVC 108-114 Kwik Clip 613210 37

KS10P-150 150PVC 159-164 Kwik Clip 613211 37

KS10P-80 80PVC 83-91 Kwik Clip 613212 37

KS10SS-15 15Cu 15-18 Kwik Clip SS 613300 37






KS10SS-65 65PVC 67-73 Kwik Clip SS 613312 37

KS10SS-150 150PVC 159-165 Kwik Clip SS 613315 37

Kwik Clip Mud Guard Washers

Lock Washers


Page No.

LN06-H M06 Lock Nut CL.5 HDG 901976 31





LN06-SS M06 Lock Nut CL.A4 (SS316) 903600 31






Page No.

NLN06-SS M06 Nylock Lock Nut (SS316) 903616 31






Page No.

MW-1/4 x 3/4 Mud Guard Washer 32

MW-1/4 x 1 Mud Guard Washer 32

MW-1/4 x 1 1/4 Mud Guard Washer 32

MW-3/8 x1 1/4 Mud Guard Washer 32


Page No.

LW06 Lock Washer 32

LW08 Lock Washer 32

LW10 Lock Washer 32

LW12 Lock Washer 32

LW16 Lock Washer 32

Lock Nut

Lock Nut - Nylock


Page No.

NC15-C 15Cu Nut Clip Powder Coated Brown 614100 38











NC40-P 40PVC Nut Clip Powder Coated White 614200 38


NC-65-P 65PVC Nut Clip Powder Coated White 614202 38





Nut Clip


Page No.

PE-10x13x35 PE Block 10ID x 13mm Wall 35OD 682022 45


















PE Block

Index

84

























































PE-102x38x182 PE Block102ID x 38mm Wall 182OD 682111 43



















Page No.

PEC-13x35 PE Block & Clip ZP 13mm Wall 35OD 683000 47
















































PE Block & Clip

index

Kwik-Smart 85


Page No.

PG100 PG B100 0 to 100 691015 54

PG250 PG B100 0 to 250 691016 54

PG400 PG B100 0 to 400 KPA 691017 54

PG1000 PG B100 0 to 1000 KPA 691020 54


Page No.

ZPC10 KS228L Purlin Clip ZP 650003 33

CPC10 KS228N Purlin Clip ZP 650004 33

Purlin Clip

Pressure Gauge

S

T

W


Page No.

SN06 M6 Slick Strut Nut ZP 647000 31





Page No.

SW06 M6 Spring Washer 31




SW16 M16Spring Washer 31


Page No.

TTP 1/4 BSP Twinlok Test Plug Brass 691000 54

TTP 1/4 NTP Twinlok Test Plug Brass 691001 54

PTP 1/4 BSP Pete’s Test Plug Brass 691002 54

PTP 1/4 NTP Pete’s Test Plug Brass 691003 54

Slick Strut Nut


Page No.

CU 25CU Stand Off Clip PC 660002

KS110-40PVC 40PVC Stand Off Clip PC 660010






Stand Off Clip

Spring Washers


Page No.

KS111-50CU 50CU Tail Clip PC 661005



KS111-40PVC 40PVC Tail Clip PC 661010





Tail Clip

Test Plug


Page No.

TR06-H Threaded Rod M06 R/H HDG Gr.4.6 33

TR08-H Threaded Rod M08 R/H HDG Gr.4.6 904020 33

TR10-H Threaded Rod M10 R/H HDG Gr. 4.6 904021 33

TR12-H Threaded Rod M12 R/H HDG Gr. 4.6 904022 33

TR16-H Threaded Rod M16 R/H HDG Gr.4.6 904023 33

TR06-H Threaded Rod M06 R/H SS Gr.316 33

TR08-SS Threaded Rod M08 R/H SS Gr.316 904036 33




TR06 Threaded Rod M06 R/H ZINC Gr.4.6 904199 33





Threaded Rod


Page No.

TK-150 150mm UltraStrut Trapeze Kit GB 31

TK-300 300mm UltraStrut Trapeze Kit GB 686000 31






Page No.

FWP10 KS25 M10 Female Wall Plate ZP 650000 33

VWP10 KS28 M10 Vertical Wall Plate ZP 650001 33

WP10 KS30 M10 Male Wall Plate ZP 650002 33

FWP12 KS25 M12 Female Wall Plate ZP 650005 33

VWP12 KS28 M12 Vertical Wall Plate ZP 650006 33

SE10 KS32 M10 Suspension Eye ZP 650008 33

HWP10 KS29 M10 Horizintal Wall Plate ZP 650009 33

HWP12 KS29 M12 Horizintal Wall Plate ZP 650010 33

Trapeze Kit

Wall Plates
















Index

86

Y


Page No.

YC15-P8 15PVC Pressure Yoke Clamp PC White 662000 39






YC20-C 20Cu Yoke Clamp Powder Coated Brown 663000 39











YC40-P 40PVC Yoke Clamp Powder Coated White 664000 39








Yoke Clamp


Page No.

WDG08 M08 Wedge Nut ZP 648000 31



Wedge Nut

KWIK-SMART METAL FRAMING| PIPE SUPPORTS| TEST PLUGS| HARDWARE

| CABLE MANAGEMENT

BUILDING SERVICES SOLUTIONS

CAT

ALOGUE

Head Office:Binder Group PTY LTD (Western Australia)26 Miles RoadKewdale WA 6105Phone: +61 (0) 8 9353 2208Fax: +61 (0) 8 9353 2751Email: [email protected]

Binder Group PTY LTD (Victoria) 12 Wedgewood RdHallam VIC 3803Phone: +61 (0) 3 9702 4360Fax: +61 (0) 3 9796 5049Email: [email protected]

Binder Group PTY LTD (Queensland)2/11-13 Allan StreetLoganholme QLD 4129Phone: +61 (0) 7 3421 0222Fax: +61 (0) 7 3421 0299Email: [email protected]

A K E E S A F E T Y P R O D U C T

Date post:	15-Sep-2018
Category:	Documents
Upload:	nguyenthuan
View:	212 times
Download:	0 times

KWIK-SMART - Binder Group · Lighter modulisation Reduce weight in buildings with no loss of...

Documents