Home >Documents >LED Electronic Price Display System - .LED Electronic Price Display System Sign, Retrofit...

LED Electronic Price Display System - .LED Electronic Price Display System Sign, Retrofit...

Date post:10-Jun-2018
Category:
View:213 times
Download:0 times
Share this document with a friend
Transcript:
  • LED Electronic Price Display System

    Sign, Retrofit Installationand Troubleshooting Guide

    VOLUME VIIIIN00935P

    rev 01/07/2010

    P1.3

    P1.1P1

    .4

    P1.2

    P1.1P2.2

    P2.1

    P3.1

    Installation ManualDra

    wings

    Insid

    e!

  • Copyright Everbrite LLC 2007, 2009

    This is the exclusive property of Everbrite LLC. Use or duplication of this document in any manner without the expressed written consent of Everbrite LLC is prohibited.

    The information contained in this document is subject to change without notice and should not be construed as a commitment by Everbrite LLC.

    Everbrite LLC assumes no responsibility for any errors that may appear in this docu-ment. Nor does it make expressed or implied warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

    Everbrite LLC shall not be liable for incidental or consequential damages in connec-tion with, or arising out of the furnishing, performance, or use of this document and the program material, which it describes.

    Trademarks CreditsEverbrite is a registered trademark of Everbrite LLC.

    lumiDigit II is a registered trademark of Everbrite LLC.

  • Table of Contents1. Manual Overview..............................................................................................................2

    2. Safety................................................................................................................................3

    3. Installer Manual................................................................................................................4A. Unpacking/Pre-Installation .........................................................................................................................4B. General Site Layout ..................................................................................................................................4C. Frame Assembly Retrofit ...........................................................................................................................7D. Typicial Sign Configuration .........................................................................................................................8E. Lamp Control Relay Instructions .................................................................................................................9F. Hard-Wire Installation ................................................................................................................................ 11G. Frame Assembly Installation ...................................................................................................................12H. T-Mount Installation Parts List ................................................................................................................14I. T-Mount Frame Assembly Diagram ..........................................................................................................15J. T-Mount Installation .................................................................................................................................16K. MID Retrofit Instructions ............................................................................................................................17L. B Wide Body Digit Assembly ......................................................................................................................18

    4. Diagrams........................................................................................................................21 A. Power Supply DC Negative Interconnect ...................................................................................................21B. Amperor Power Supply Wiring ...................................................................................................................26C. Retrofit Wiring Example .............................................................................................................................28D. Dual Sign Interconnect ..............................................................................................................................29E. Controller ...................................................................................................................................................30

    5. Troubleshooting Guide ................................................................................................32

    6. EMC (Everbrite Message Center).................................................................................36

    A. EMC Retrofit Installation Guide ..................................................................................................................36B. EMC/LD2 Wiring ........................................................................................................................................37C. Basic EMC Panel Wiring Information .........................................................................................................38D. Basic EMC Controller Plate Wiring Information .........................................................................................39E. EMC Wiring Diagram .................................................................................................................................40F. EMC Troubleshooting Guide ......................................................................................................................41

    7. Contact Information & Warranty...................................................................................431. MANUAL OVERVIEWThis manual is intended for the installation of Everbrites lumiDigit II sign using the Model 6002 console. Read this manual carefully before starting the equipment.This manual contains important information for correct installation and maintenance of the equipment.It also contains important instructions to prevent accidents, personal injury and/or serious damage prior to or during opera-tion of the equipment.Familiarize yourself thoroughly with the function and operation of this equipment and strictly observe the directions given.If you have any questions or need further details on specific aspects related to the lumiDigit II Sign, please do not hesitate to contact us.

    In this manual you will find three levels of flagged notes or warnings.

    WARNING! ThE warnIng mEssagE Is usED whEn a LIfE ThrEaTEnIng sITuaTIon may arIsE or pErsonaL Injury Can rEsuLT.

    CAUTION! The caution message is used when there is a danger of damage to the equipment, materials, or other important information; such as warranty issues.

    NOTE: The note message is used to give operational information and useful tips.

  • 3

    2. SAFETY The owner of the lumiDigit II Sign is responsible for safe operation and repair. Therefore, the owner is obliged to familiarize operating personnel with the contents of this manual and make them aware of all possible hazards.

    NOTE: when using this equipment, always follow the manufacturers instructions for safe operation. In case of emergency, please telephone Technical support or a qualified service technician.

    Do not operate the sign until it is completely assembled and installed per the instructions sup-plied by Everbrite.

    Everbrite recommends that your main power be installed by a licensed electrician in accordance with the local building and electrical codes.

    All equipment must be grounded in accordance with the local building and electrical codes.

    If any part of the lumiDigit II sign equipment is malfunctioning or has been damaged stop all operation and consult with Everbrite Technical Support or qualified service personnel before further use.

    Use only Everbrite specified or recommended replacements parts.

    WARNING! ShUT OFF POWER TO ThE SIGN AT ThE SITE CIRCUIT bREAkER bOx. USE A LOCK OUT/TAG OUT DEVICE ON CIRCUIT BREAK-ERS OR POWER ON/OFF SWITCHES WHEN PERFORMING INSTALLATION, REPAIRS, OR MAINTENANCE.

    When performing repairs be mindful of the weather and work area conditions. Avoid the units exposure to the elements, water and debris, or anything that may be dangerous or cause dam-age to the equipment.

    warnIng! opEraTIon of ThE unIT wITh ThE ELECTrICaL CIrCuITry ExposED Is DangErous. BE surE aLL TooLs anD any oThEr maTErIaLs arE rEmovED from ThE unIT. BE surE aLL aCCEss CovErs arE rEpLaCED anD CLosED BEforE powEr Is TurnED on.

    CauTIon: use of solvent, cleaners, or a power washer on your lumiDigit II sign may cause permanent damage.

    CauTIon: Existing gasket strips must be removed and frames must be scraped and cleaned before new gasket strip is installed. failure to do so will compromise the water tight seal of the sign.

  • 4

    CauTIon: Everbrite recommends that the sign be installed by a licensed contractor. must be installed per the detailed instructions sent with the unit and meet all local and national building codes.

    Regular

    Mid-Grade

    Premium

    lumiDigit II sign

    Conduit

    mounting Bolts

    aC main

    Circuit Breaker panel

    outlet

    Controller Keypad

    3. INSTALLER MANUAL

    A. Unpacking/Pre InstallationInstallation hardware and any additional items will vary depending on the sign configuration ordered.

    NOTE: Take care uncrating so as not to damage the units.

    NOTE: During installation check all connectors on the cable harnesses to ensure good connections.

    The shipment should include: lumiDigit II Manual (leave with sign) lumiDigit II Sign Console Keypad with AC Adapter Installation Hardware

    b. General Site LayoutThere will be a set of Installation instructions/drawings included wit

Click here to load reader

Embed Size (px)
Recommended