M 1 issued by H.H. Angus and Associates · shall be indicated on the Tender Proposal....

ADDENDUM 1

PROJECT

FROM Nancy Chao

Learning Centre Renovation DATE May 9, 2019

PROJECT 16-117

ADDRESS 30 The Queensway - Barnicke Bldg PAGES 25

St. Joseph's Health Centre

The following changes, additions, deletions and clarifications are hereby made an integral part of the documents, including the drawings and specifications for the above project. Acknowledgment for receipt of this addendum shall be indicated on the Tender Proposal.

Architectural:1. New Item: Architectural drawing A100 - Demolition and Proposed Plans and RCPs. Replace in its entirety the previously issued drawing A100 - Demolition and Proposed Plans and RCPs, dated May 3, 2019 with the attached drawing.

2. New Item: Architectural drawing A401 - Interior Elevations (1 page).Replace in its entirety the previously issued drawing A401 - Interior Elevations, dated May 3, 2019 with the attached drawing.

3. New Item: Refer to the attached A100 - Demolition and Proposed Plans and RCPs (1 page). GC to provide a separate price for the following scope of work for Auditorium A & B:

i. Refer to specification section 09 51 13 Acoustical Panel ceilings -2.2. Materials: Change acoustic ceiling tile from ACT1 to ACT2 type.

ii. Refer to Electrical & Mechanical addenda #1 for corresponding changes.

4. New Item: Add attached specification section 09 72 10 Dry erase Projectable Wallcovering annotated as "WB" in the drawings (4 pages). Refer to the attached drawing A401. Replace all "WBP" with "WB" within the project area.

5. New Item: Refer to specification section 12 24 00 Motorized roller shades annotated as "MRS". Replace in its entirety with the attached specification 10 24 00 Manual Roller Shade (3 pages). Replace all "MRS" with "RS" within the project area.

6. New Item: Refer to drawing 12/A401: Delete in its entirety M1 millwork. GC to provide continuous furring wall as shown in 1/A100 near gridline 7 & E/D complete with WB finish.

7. New Item: Refer to drawing 1/A100 near gridline 7/C: GC to protect and maintain existing kitchenette and plumbing in Meeting Room B1-12A, refer to Mechanical addendum #1.

Mechanical:1. Refer to the attached mechanical addenda M‐1 issued by H.H. Angus and Associates (9 pages).

Electrical:1. Refer to the attached electrical addenda E-1 issued by H.H. Angus and Associates (6 pages).

End of Section

F E D

3

4

5

6

7

8

9

C

EX AV Rack to be removed and handed over to client

EXEX

D6

D3

D4D6

EX

D5

D5

D5D3

D3

D7

D8

D8

D7

D10

D11 D11 D11

D11

D12

D12

D12

D8

D8

D5

D8

D5

D7

D7

D7

D11

D11

D8 D8

EX flooring to remain

9455 9455 6230

3750

3765

3575

3910

3525

N

GENERAL NOTES

1. Existing health and safety equipment on walls to be removed, stored, protected and reinstalled. GC to confirm location with client prior to installation (e.g. hand sanitizer stations, existing convinience phones, emergency phones etc).

2. All existing signage to be removed, stored and relocated as per client's instructions.

3. Patch, paint and repair existing areas damaged during construction.

4. Any removed A.V, I.T and electrical equipment to be handed over to the client.

5. All hoarding to receive graphic wrap, refer to specifications.

DEMOLITION LEGEND

EX

Existing element to be demolished

Existing Door c/w FrameHardware to be salvagedRefer to Door Schedule for locations of re-use.

Flooring and cove base to be removed

Ceiling to be removedRetain existing light fixtures and ACT tiles to handed over to hospital for re-use.

HoardingAll hoarding to receive graphic wrap. Refer to Specifications

F E D

3

4

5

6

7

8

9

C

A401 1

MEN'S WR106A

AUDITORIUMB

B1-11B

WOMEN'SWR

106B

COLLABORATORYB1-12

MEETINGROOMB1-12A

TYP

CLOSETB112B

P2d

4A506

EX107

EX

12

A

EX

12

AUDITORIUMA

B1-11A

D11B

D11A

3

4

2

A401 5

7

8

6

A401

9

1011

12

A40113

14

15

16

new operable partition closet

AP

AP

QUIETSTUDYB1-12B

P2d P2d

P2dWB

P3aP3a

P3a

P3a

P3a P3a

P3a

P3a

P3a

P3aP3a

P3a

P3a

P2d

2200

P2d

P2d

1240

1600

210

13035

6660

8830

8605

4570

EX

11

A

AP

WB

A401 19

AV ClosetB1-12D

EX12B

D12D

GC to coordinate with AV, provided by Owner

3200

WB

1320

1295

875

D11F

A401 17

915

M1WB

2155

P2c

P2c

P1b

AP

AP

ACR ACR ACR

AP

AP

M3

D11C OPA, refer to structural drawings

3650

2535

1150

4945

1106

5

1183

5

5430

905

ALIGN

D155

EX104A

4435

455

4275

A401

20

all EX mech. grilles to receive new PT finish



9455 9455 6230

3910

3750

3765

3575

2155 VIF

VIF

795

VIF

650

VIF

1335

VIF

1335

VIF

1525

VIF

2185

VIF

1940

WB

ACR

ACR

WB

Wiremold, refer to elec. dwgs.




Floor to be repaired to make good and match EX floor finishes + cove base

F E D

3

4

5

6

7

8

9

C

COLLABORATORYB1-12

MEN'S WR106A

WOMEN'SWR

106B

MEETINGROOMB1-12A

AUDITORIUMB

B1-11B

2395

±

8540 (± VIF)

C3

C3

C1

C1

ACT2

3023

1

A505

SIM

RS

RS

C2

C2

STAIRS A1B-213

P

345

LB

LB

LB

LB

LB

BULKHEAD WALL

GWB

2710

BULKHEAD WALLSAROUND ACT, TYP

EXTENT OF GWB COVE CEILING

AUDITORIUMA

B1-11A

Note: -GC to coordinate concealed GWB access panels with consultant. Refer to specs, TYP.

RS

RS

RS

1

A505

SIM

1

A505

SIM

1

A505

SIM

1

A505

SIM

1

A505

SIM

1

A505

SIM

1

A505

SIM

New downlights to replace EX typ., ref. to Elect.

New downlights to replace EX typ.

ACT2

3023

STLB

1280

815

2355

L2

L1

L4 L4 L4

L4 L4 L4

L4 L4 L4

L4 L4 L4

L4 L4 L4

L4 L4 L4

L4 L4 L4

L4 L4

L4 L4

L4 L4

L4L4L4 L4L4

L4

L4

L4

L4

L4

L4

L4

L4

L4L4L4 L4L4

L5

L5

L5

L5

L2 L2 L2 L2

L2 L2 L2 L2 L2

L2

P

L2

L2

L2 L2 L2 L2 L2

L2 L2 L2 L2

835 1950

L3

L3

L3

L1

L1

L1

L1

L1

L1

L1

L1

L1L1

L1

EQ

EQ

705

1525

675

1525

1525

335

1525

705

1525

VIF

1565

EQ

EQ

GWB

2692EX

3100

GWB

2700EX

3100

EX TV

New fixtures to replace EX, Refer to Electrical, TYP.

L1 L1 L1L1

EQ EQ EQ EQ EQ

PS

PS

435

560C4 GWB

2997

EQ EQ

795 EQ

ST

EX. perimeter wood cove fascia to be refinished to match WD

P

GWB

2710

GWB

2710

AV ClosetB1-12D

CLOSETB112B

8885

3670

4840

595

675

665

200

L1

L1

200

Bulkhead wall above OPA

L3

L3L3

L3

L3

L3L3

L3

9455 9455 6230

3910

3750

3765

3575

EX structural beam to be reused, ref. to structuralNew structural beam, ref. to structural

ST

EQ

EQ

EQ

EQ

L1

L1E

Q11

65

EQ

EQ

C5

GWB

2743

GWB

2743

3485

3555

ST

L2

L2

780

SA SA

SA SA

SA SA

SA

F E D

3

4

5

6

7

8

9

C

COLLABORATORYB1-12

MEN'S WR106A

WOMEN'SWR

106B

MEETINGROOMB1-12A

AUDITORIUMB

B1-11B

STAIRS A1B-213

LX

LX

EXTENT OF GWB COVE CEILING

AUDITORIUMA

B1-11A

D2

D3

D3

D3

D9D12

D12

D2

D2

D2

9455 9455 6230

3910

3750

3765

3575

ALL DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS ANDDESIGN ARE THE COPYRIGHT PROPERTY OF THE ARCHITECTAND MUST BE RETURNED UPON REQUEST. REPRODUCTION OFTHE DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS ANDDESIGN IN WHOLE OR IN PART IS STRICTLY FORBIDDEN WITHOUTTHE ARCHITECT'S WRITTEN PERMISSION. THIS DRAWING SHALLNOT BE USED FOR CONSTRUCTION PURPOSES UNLESSCOUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale: As indicated

16-117

CB/FG

PH/NC

A100

SJHC LEARNING CENTRE

30 THE QUEENSWAYTORONTO, ON M6R 1B5

DEMOLITION ANDPROPOSED PLANS ANDRCPs

1 : 1002 LEVEL 1 - CONFERENCE DEMO PLAN

KEY PLAN

DEMOLITION NOTES

D2 EX stepped ceiling (at 2700mm - 3000mm) to be demolished atperimeter of room.

D3 Remove EX blinds and handover to client. Patch, repair and paintwindow surroundings to make good for new motorized roller shade(MRS).

D4 EX wall finish, exterior glazing and wall fin to remain and receivenew PT finish.

D5 Patch & level EX CONC floor as required to prepare floor to receivenew floor finish (TYP) as part of ACP3.

D6 EX folding partition to be removed. Structural support beam toremain & be reused, refer to Structural.

D7 Remove & store or Protect EX artwork during construction. Ownerto confirm final mounting locations.

D8 Remove any EX acoustic wall panel, wainscotting and bulletinboards from rooms.

D9 EX ceiling mounted TV to remain and be protected duringconstruction.

D10 Line of hoardingD11 Remove EX doors and replace with new. Reuse EX hardware.D12 EX AV equipment to be removed & handed over to client for reuse.

No. ISSUED/REVISED DATE

1 ISSUED FOR BLDG PERMIT June 19 20172 ISSUED FOR TENDER Jan. 30, 2018

3 ISSUED FORCONSTRUCTION

May 1, 2018

4 RE-ISSUED FOR BUILDINGPERMIT

April 18, 20195 ISSUED TO CLIENT May 3, 20196 ISSUED FOR ADDENDUM 1 May 9, 2019

1 : 1001 LEVEL 1 - CONFERENCE PROPOSED PLAN

1 : 1003 Level 1 - AUDITORIUM RCP

RCP NOTES

NOTE DESCRIPTION

C1 New RS affixed to underside of window bulkheadC2 Approximate location of new ceiling-mounted projector. Refer to

electrical and AV documents.

C3 Recessed ceiling-mounted projector screen. Refer to electricaland AV documents.

C4 Refer to AV documents for AV equipment, exact locations to bedetermined on site.

C5 Ceiling to be repaired to make good and match EX ceiling tileand grid.

1 : 1004 Level 1 - AUDITORIUM DEMP RCP

MRS @ U/S OF EX OPENINGREFER TO SPECIFICATIONS

EX

PT-1

CB

WD (P2D)

PT-1

CB CB

PT-1PT-1

RECESSED PROJECTOR SCREEN C/L TO PROJECTORREFER TO AV DOCUMENTS

WDLINE OF PS (NIC)

2700

D1

1F

SIM1

A505

SIM1

A505

2600

100

CB CB CB

PT1PT1

EX

11

A

PT1

BBBB AP AP APAPAPAP AP

EQEQEQEQEQ360Align

SIM1

A505

SIM1

A505

2185

Folding parititon, refer to specification

PT1

SIM1

A505

SIM1

A505

Folding parititons (10 panels)

SIM1

A505

SIM1

A505

AP

CB

PT1

2300

EQ EQ

D11

B

525

BB AP

WV PT1

SIM1

A505

SIM1

A505

2080

100

CBCBCBCB


CBCB CB

PT1

PT1 PT1 PT1

AP AP APBB BB

EQEQEQ 300

300

3320

SIM1

A505

SIM1

A505

2080

100

EX glazing

PT1

CB

WD (P2D)

15 g

ap

LINE OF PS (NIC)

D12

D

D11

F

SIM1

A505

SIM1

A505

CB

EX Glazing


2690


1345

760

CB

PT1 PT1

EX Glazing

CB

BB

PT1

1360 2155 1080 280

PT1

WBWB WBShort-Throw Projector, N.I.C.

PT1PT1

CB

M1

WALL MOUNT PROJECTOREXACT LOCATION TO BE CONFIRMED BY

AV CONSULTANT PRIOR TO INSTALL

PLAM

Short-Throw Projector, N.I.C.

EQ EQ

WB

CB

EQ EQ

915

SS

EX

10

4A

D15

5

1345

760

1345

760

2155

2160

WB


WB

WB WB

EQ EQ EQ

PT1

Logo location (NIC)

760

1345

CB

PT1

300

WB AP AP

1345

1000

1190 2160 650 650 1000

760

1345

WB

EQ EQ


WB


EX Glazing

CB

PT1

PT1

CB

PT1

115

2080

6570

AP1480 300 920 630 1480 1480 300

AP AP AP APBB BB

CB

PT1

CB

EX

12

A

EX millwork

Wall at angle

APAPBBAP

CB

Align to door

PT1

D11

A

D11

C

BB

820 300 920 1400 630 300

AP

WD

PT1

SIM1

A505

SIM1

A505

CB CB

2080

100

CBCBCB

WBPT1

CB CB

EX

12

WB WB

WB

WB

WB

735 2440 2440 505

WB

WB

WB

WB

WB

WB

D11

B

D11

A

PT1

PT1 PT1 PT1

CB CB CB CB

Wall at angle

2745

PT1

PT1

ACR on adjacent

walls

ACR on adjacent

walls

Donor wall location (NIC)

ACR

2625

895

25mm high alum u-channel, top/bottom TYP.

alum L-channel to conceal vertical edges TYP.

EX electrical panel

100

2450

PT-1

25

APAPAP

EQ EQ EQ

RB

ALL DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS ANDDESIGN ARE THE COPYRIGHT PROPERTY OF THE ARCHITECTAND MUST BE RETURNED UPON REQUEST. REPRODUCTION OFTHE DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS ANDDESIGN IN WHOLE OR IN PART IS STRICTLY FORBIDDEN WITHOUTTHE ARCHITECT'S WRITTEN PERMISSION. THIS DRAWING SHALLNOT BE USED FOR CONSTRUCTION PURPOSES UNLESSCOUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale: As indicated

16-117

CB/FG

PH/NC

A401


30 THE QUEENSWAYTORONTO, ON M6R 1B5

INTERIOR ELEVATIONS

1 : 501 AUDITORIUM B - NORTH ELEVATION


1 ISSUED FOR BLDG PERMIT June 19 20172 ISSUED FOR TENDER Jan. 30, 2018

3 ISSUED FORCONSTRUCTION

May 1, 2018

4 RE-ISSUED FOR BUILDINGPERMIT

April 18, 20195 ISSUED TO CLIENT May 3, 20196 ISSUED FOR ADDENDUM 1 May 9, 2019

1 : 506 AUDITORIUM A - EAST ELEVATION

1 : 507 AUDITORIUM A - WEST ELEVATION

1 : 502 AUDITORIUM B - EAST ELEVATION

1 : 504 AUDITORIUM B - SOUTH ELEVATION

1 : 503 AUDITORIUM B - WEST ELEVATION

1 : 505 AUDITORIUM A - NORTH ELEVATION

1 : 509 COLLABORATORY - WEST ELEVATION

1 : 5010 COLLABORATORY - NORTH ELEVATION

1 : 5011 COLLABORATORY - SOUTH ELEVATION

1 : 5013 CLASSROOM - SOUTH ELEVATION

1 : 5014 CLASSROOM - WEST ELEVATION

1 : 5015 CLASSROOM - NORTH ELEVATION

1 : 5016 CLASSROOM - EAST ELEVATION

1 : 508 AUDITORIUM A - SOUTH ELEVATION

1 : 5012 COLLABORATORY - EAST ELEVATION

1 : 2518 ACR Graphic Template

1 : 5019 CAFETERIA ELEVATION

1 : 5017 Typical Alcove

1 : 5020 QUIET STUDY - EAST ELEVATION

REFER TO SPECIFICATIONS TYPICAL OF 5 PANELS, REF. TO PLAN

nchao

Line

09 72 10 DRY ERASE PROJECTABLE WALLCOVERING

PAGE 1

PART 1 – GENERAL 1.1 RELATED DIVISIONS 1. Division 26 51 00 Interior Lighting.

2. Division 09 20 00 Plaster and Gypsum Board: Wall substrate. 3. Division 09 91 23 Interior Painting: Priming for vinyl wall coverings.

4. Division 09 72 16.13 Flexible Vinyl Wall Coverings. 5. Division 10 11 00 Visual Display Surfaces: Chalk and markerboards.

1.2 REFERENCES

1. American Society for Testing and Materials ASTM E84 Test Method for Surface Burning Characteristics of Building Materials.

2. Gypsum Association GA-214-M-97 Recommended Levels of Gypsum Board Finish. 1.3 SUBMITTALS

1. Manufacturer’s product data and installation instructions for each type of dry erase wallcovering, adhesive, and accessories required.

2. Manufacturer’s written product data indicating compliance with specified materials required. 3. Manufacturer’s written installation instructions. 4. Manufacturer’s written instructions for recommended maintenance of each type of dry erase

wall covering required. 5. Samples:

1. 7 inch (177.8mm) x 9 inch (228.6mm) samples of each dry erase material required.

2. 6 inch (152.4mm) samples of trim, tray, and end caps required. 1.4 QUALITY ASSURANCE

1. Manufacturer: Provide each type of dry erase wallcovering required produced by one manufacturer. 2. Surface Burning Characteristics Classification: Provide materials that meet Class I/A rating

when tested in accordance with ASTM E84 for flame spread and smoke developed. 3. Field Samples: Prepare field samples for architect’s review and establish requirements for seaming and finish trim. 4. Install sample panel of each type presentation wallcovering specified in area designated by

architect. 5. Maintain corrected and approved samples to serve as a standard of performance for the

project. 6. Installer: Installation by skilled commercial wallcovering contractor with no less than three

years of documented experience installing dry erase wallcovering of the types and extent required.


PAGE 2

1.5 PRODUCT DELIVERY, STORAGE, AND HANDLING 1. Deliver presentation wallcoverings to the project site in unbroken and undamaged original

factory packaging and clearly labeled with the manufacturer’s identification label, quality or grade, and lot number.

2. Store materials in a clean, dry storage area with temperature maintained above 55°F (13°C) with normal humidity. 3. Store material within original packaging to prevent damage.

1.6 PROJECT CONDITIONS 1. Do not apply presentation wallcoverings when surface and ambient temperatures are

outside the temperature ranges required by the wallcovering manufacturer. 2. Provide continuous ventilation and heating facilities to maintain substrate surface and

ambient temperatures above 55°F (13°C) unless required otherwise by manufacturer’s instructions.

3. Apply adhesive when substrate surface temperature and ambient temperature is above 55°F (13°C) and relative humidity is below forty percent.

4. Maintain constant recommended temperature and humidity for at least 72 hours prior to and throughout the installation period, and for 72 hours after wallcovering installation completion.

5. Provide not less than 80-foot-candles per square foot lighting level measured mid-height at substrate surfaces.

1.7 ` WARRANTY

Submit manufacturer’s limited five-year written warranty against manufacturing defects. 1.8 MAINTENANCE

Maintenance instructions: Include precautions against cleaning materials and methods that may be detrimental to finishes and performance.

PART 2 - PRODUCTS 2.1 MANUFACTURER

1. Wallcoverings: Walltalkers Wallcoverings manufactured by Koroseal Interior Products, LLC., Fairlawn, Ohio, and distributed by Blue Sky Agency. 2. Egan VersaPro manufactured by Egan visuals Inc. and distributed by Metro Wall Coverings. 3. Architect approved Alternate.

2.2 MATERIALS 1. (WB) Walltalkers matte•rite: Smooth low gloss vinyl surface for projection and dry

erase markers or approved similar. 1. MP60: 59/60 inch (1.50/1.52m) width, non-woven backing, white finish.


PAGE 3

2. Thickness: 0.43mm 3. Hang: reverse every other strip. 4. Flammability testing: Class A. 5. Substrate primer: white pigmented acrylic base primer/sealer specifically formulated for

use with vinyl wall coverings. 6. Mounting substrate: MDF substrate, continuous finished mounting surface to be

equivalent of GWB level 4 finish per GA-214-M-97. 2. Composition:

1. matte•rite®: Provide non-woven backing with white pigmented vinyl capped with dry erase low gloss film, or approved similar.

2.3 TRIM & TRAY

1. Aluminum Tray: Clear satin, anodized aluminum, snap-on marker and eraser tray with Clips. Specify length: 4’ length and 8’ length refer to elevations.

2. End Caps: 1. ET03-00: 1/2 inch (13mm) anodized tray end cap set for marker and eraser tray. 3. Trim: Elite trim with 1/8” reveal, Supplier: Architectural School products or approved similar. Trim to be provided on all exposed perimeter edges. 2.4 ACCESSORIES 1. Adhesives: Heavy-duty clear or clay based premixed vinyl adhesive. 2. Substrate Primer/Sealer: White pigmented acrylic base primer/sealer specifically formulated for use with vinyl wallcoverings. 3. Broad Tip Dry Erase Markers: 1. EC12-99: Chisel BLK - 12CT 2. EC04-00: Set of four colors: red, blue, green, black. 4. Eraser: 1. DEFE-99: Dry erase felt eraser. 2. DECC-Y1: Dry erase cleaning cloth - yellow. PART 3 - EXECUTION

3.1 EXAMINATION

1. Examine substrates and installation conditions to ensure surface conditions meet or exceed a Level 4 finish, per GA-214-M-97: Recommended Levels of Gypsum Board Finish, and permanent lighting should be installed and operational.

2. Test substrate with suitable moisture meter and verify that moisture content does not exceed four percent.

3. Verify substrate surface is clean, dry, smooth, structurally sound, and free from surface defects and imperfections that would show through the finished surface.

4. Evaluate all painted surfaces for the possibility of pigment bleed-through. 5. Notify the contractor and architect in writing of any conditions detrimental to the proper and

timely completion of the installation.


PAGE 4

6. Beginning of installation means acceptance of surface conditions. 3.2 INSTALLATION Wallcovering backing.

1. Acclimate wallcovering in the area of installation a minimum of 24 hours before installation. 2. Read and follow the manufacturer’s installation instruction sheet contained in each roll of the

dry erase wallcovering. 3. Examine all materials for pattern, color, quantity and quality, as specified for the correct

location prior to cutting. 4. Primer: Use a quality pigmented acrylic wallcovering primer. 5. Adhesive: Apply a uniform coat of heavy-duty pre-mixed clay-based or extra strength clear wallcovering adhesive. 6. Install each strip horizontally and in the same sequence as cut from the roll. 7. Install dry erase wallcovering sheets in exact order as they are cut from bolt. Reverse hang

alternate strips (except lined products). Do not crease or bend the wallcovering when handling.

8. Install dry erase wallcovering horizontally using a level line. 9. Using a level or straight edge, double cut the seam with a seam-cutting tool (Ex: Double Seam-Cutter or Swedish Knife). Do not score drywall or plasterboard when cutting material. 10. When covering the entire wall, seam the material out of the main writing and viewing areas

of the wall. 11. Apply wallcovering to the substrate using a wallcovering smoother, wrapped with a soft

cloth, to remove air bubbles. Do not use sharp edged smoothing tools. Smooth material on the wall from the middle to the outside edge.

12. Remove excess adhesive immediately after the wallcovering is applied. Clean entire surface with a warm mild soap solution, and clean soft cloths. Rinse thoroughly with water and let dry before using. Change water often to maintain water clarity.

13. Stop installation of material that is questionable in appearance and notify the manufacturer’s representative for an inspection.

3.3 CLEAN-UP

A. Upon completion of installation, remove all exposed adhesive immediately using a soft cloth and a warm, mild soap solution and rinse thoroughly with water and dry with clean towel prior to using.

B. Upon completion of the work, remove surplus materials, rubbish, and debris resulting from the wallcovering installation. Leave areas in neat, clean, and orderly condition.

END OF SECTION

SECTION 10 24 00 Manual Roller Shade

Page 1

Part I – GENERAL

A. SUMMARY 1. Section Includes

a. Manual Operated Roller Shade 2. Related Work includes the following

b. Section 06100 Rough Carpentry c. Section 08520 Aluminum Windows

B. REFERENCES 1. National Fire Protection Association (NFPA) 701 2. Department of Transportation Motor Vehicle Safety Standard 302 Flammability of Interior

Materials 3. California Administrative Code Title 19 4. Federal Standard 191 Method 5903 (used by Port Authority of New York and New Jersey

for drapery, curtain, and upholstery material) 5. Boston Fire Department Test BFD IX-1 6. New York State Uniform Fire Prevention and Building Code

C. SUBMITTALS 1. Subject under provisions of Section 01 33 00 – Submittal Procedures 2. Product Data: Manufacturer’s data sheets shall be submitted for each product specified,

including: a. Preparation instructions and recommendations b. Finishes, material descriptions, dimensions of individual components c. Construction and installation instructions d. Manufacturers recommendations for maintenance and cleaning

3. Drawings and Diagrams: Product details, installation details, working and assembly drawings shall be supplied as requested

4. Sample: Responsible contracting officer or agent shall supply one sample shade of each type specified in this contract for approval. Supplied units shall be furnished complete with all required components, mounting and associated hardware, instructions and warranty.

5. Electric shade motors shall comply with UL standards. Copy of compliance available for submission upon request.

D. QUALITY ASSURANCE 1. Supplier: Manufacturer, subsidiary, or licensed agent shall be approved to supply the

products specified, and to honor any claims against product presented in accordance with warranty.

2. Installer: Installer or agent shall be qualified to installed specified products by prior experience, demonstrated performance and acceptance of requirements of manufacturer, subsidiary, or licensed agent. Installer shall be responsible for an acceptable installation.

3. Uniformity: Provide product of only one manufacturer for entire project. 4. Mock up: Provide one (1) mock-up shade for each roller shade type/assembly specified.

E. DELIVERY, STORAGE, AND HANDLING 1. Product shall be delivered to site in manufacturer’s original packaging. 2. Product shall be handled and stored to prevent damage to materials, finishes, and

operating mechanisms. F. JOB CONDITIONS

1. Prior to shade installation, building shall be enclosed.


Page 2

2. Interior temperature shall be maintained between 60 degrees Fahrenheit and 90 degrees Fahrenheit during and after installation; relative humidity shall not exceed 80%. Wet work shall be complete and dry.

G. WARRANTY 1. Provide a limited manufacturer’s warranty from date of Substantial Completion covering

the following periods. a. Lifetime Limited Warranty on all hardware components, fabrics warrantied for 5 years

by Hunter Douglas, and most fabrics warrantied for 10 years by the fabric manufacturer. Specific and custom product warranties available from manufacturer or its authorized agent.

Part II – PRODUCTS

A. ACCEPTABLE MANUFACTURER 1. Lutron or architect approved equivalent. 2. Request for substitutions must be approved by architect minimum of 7 days prior to close

of bid. B. (RS) MANUAL CONTRACT DUAL ROLLER SHADE C. FABRICS: Inherently anti-static, flame retardant, fade and stain resistant, light filtering, room

darkening, and blackout fabrics providing 5% openness, 5 oz/sq. yd to 20.70 oz/sq. yd, containing fiberglass, vinyl content. Colour to TBD.

D. Horizontal stabilizing battens are not required, nor will they be accepted.

1. CONTROL SYSTEMS: .

a. CLUTCH OPERATED: Chain-driven operator capable of operating fabric panels from 13 to 16 feet wide (maximum width varies by fabric weight) and up to 20 feet tall with a maximum allowable pull force of 9 pounds. Utilization of adjustment-free continuous qualified T304 stainless ball chain with 110 lbs. breaking strength for precise control, smooth operation, and ensures a uniform look. Components must be maintenance-free from adjustments or lubrication for trouble-free lifetime operation. 1. 90 pound breaking strength chains will not be accepted. 2. Chain anchor device to be compliant with WCMA safety standard A100.1.1-

2010 and must prevent the clutch system from moving the roller shade through lowering and raising if not properly installed as specified in ANSI Standard Section 6.5.2.

b. ROLLER TUBE: Circular-shaped aluminum tube extruded from alloy and temper 6063 T-6. Extruded tube to have a .063” wall thickness (2.5” outside diameter to have a 0.79” wall thickness). Heavily reinforced with minimum of six internal ribs and flutes providing additional tensile strength and allows for secure placement of clutch and end plug.

c. SPRING-LOADED IDLE END: Reinforced idler assembly containing spring loaded end plug with positive locking wheel allowing for up to 7/8” adjustment and provides for a secure installation and removal of shade. Locking tube bearing plug contains minimum 6 ribs and flutes and inserted a minimum of 2 3/8” into roller tube on heavy duty systems.

d. BOTTOM BAR: Industry standard sealed hembar with weight sewn into pocket providing for tracking adjustments and uniform look of the hanging fabric panel. Options include: Bottom Bar, aluminum finish.

e. MOUNTING HARDWARE: Manufacturer’s standard or heavy duty bracket constructed of hardened 1/8” thick steel to support full weight of shade with


Page 3

bracket and screw hole covers to provide uniform look. Locking mechanism on bracket adapter provides for a secure installation and removal of the shade. 1. Cradle-seated hardware without a locking mechanism will not be accepted.

f. INTEGRATED LEVELING DEVICE: Built into the idle-end bracket (or intermediate bracket of a coupled shade) allowing for the vertical height adjustment of +/- one-half inch direction up or down, allowing the easy leveling of a fabric panel on its mounting surface. This assists to keep the fabric rolling square to the tube, minimizing the chance of the fabric rolling into its hardware causing creases and damage to the ends of the fabric. 1. Adjusting fabric skewing through means of tape, paper, or cardboard tucked

up inside the fabric at the tube is not acceptable. g. FASCIA: Ceiling-mounted L-shaped removable aluminum extrusion valance that

attaches to brackets and conceals roller shade. Fascia at the bottom enclosure must allow a maximum of 1” gap to allow fabric to come through. Exposure underneath greater than 1” is not to be accepted.

h. BLOCKOUT SYSTEM: Extruded aluminum side channel with concealed mounting brackets. Bottom bar with Nylon wool pile to prevent light leakage.

E. FABRICATION 1. Shade measurements shall be accurate to within +/- 1/8” or as recommended in writing

by manufacturer. F. FABRICS: Fabric: include full range of Avila blackout blinds and Basketweave. Colour and

openness TBD.

Part III – EXECUTION

A. Inspection 1. Subcontractor shall be responsible for inspection on site, approval of mounting surface,

installation conditions, and field measurement for this work. 2. Other interacting trades shall receive drawings of shade systems, dimensions, assembly,

and installation methods from subcontractor upon request. B. Installation

1. Installation shall comply with manufacturer’s specifications, standard and procedures as detailed on contract drawings

2. Adequate clearance shall be provided to permit unencumbered operation of shade and hardware.

3. Clean finish installation of dirt and finger marks. Leave work area clean and free of debris.

C. Demonstration 1. Demonstrate operation method and instruct owner’s personnel in the proper operation

and maintenance of the roller shades.

END OF SECTION

St. Joseph’s Health Centre Learning Centre Revisions HHA #2161346-02

Section M-1Addenda M-1

Page 1 of 1

H.H. Angus and Associates

ADDENDA M-1

The information listed below is to form part of the Contract Documents. All associated costs are to

be included in Tender Price shown on Tender Form. Acknowledgment of this Addendum, by number, to be shown in space provided on Tender Form.

1 DRAWINGS

1.1 M001 – Mechanical Legend & Drawing List (re-issued)

.1 Replace previously issued version of this drawing with the copy attached herewith.

1.2 M002 – Mechanical Schedules (re-issued)


1.3 M100 – Level 1 Plumbing Demo (re-issued)


1.4 M200 – Level 1 Heating Demo (re-issued)


1.5 M201 – Level 1 Heating New (re-issued)


1.6 M300 – Level 1 Ventilation Demo (re-issued)


1.7 M301 – Level 1 Ventilation New (re-issued)


1.8 M400 – Level 1 Fire Protection Demo and New (re-issued)


END OF ADDENDUM

As indicated

M001


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

MECHANICAL LEGEND

AND DRAWING LIST

KEY PLAN


ALL DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS AND

DESIGN ARE THE COPYRIGHT PROPERTY OF THE ARCHITECT

AND MUST BE RETURNED UPON REQUEST. REPRODUCTION OF

THE DRAWINGS, SPECIFICATIONS, RELATED DOCUMENTS AND

DESIGN IN WHOLE OR IN PART IS STRICTLY FORBIDDEN WITHOUT

THE ARCHITECT'S WRITTEN PERMISSION. THIS DRAWING SHALL

NOT BE USED FOR CONSTRUCTION PURPOSES UNLESS

COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5


HHAngus & Associates Limited Consulting Engineers1127 Lesl ie Street , Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290

2161346

ISSUED FOR ADDENDUM #M11. 2019/05/09

As indicated

M002


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

MECHANICAL SCHEDULES

KEY PLAN

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346


As indicated

M100


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 PLUMBING DEMO &

NEW

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346

KEY PLAN


As indicated

M200


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 HEATING DEMO

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5


HHAngus & Associates Limited Consulting Engineers1127 Lesl ie Street, Toronto, ON, M3C 2J6 Canadawww.hhangus.com | T 416 443 8200 | F 416 443 8290

2161346

KEY PLAN


DISHWASH

1B-110

VENDING

MACHINES

101

CORRIDOR

1B-101A

AUDITORIUM

B

B1-11B

COLLABORATORY

B1-12

MEETING

ROOM

B1-12A

CORRIDOR

C101

ECOLOGIZER

1B-110B

JANITORIAL

1B-110A

MEN'S WR

106A

WOMEN'S

WR

106B

STAIRS A

1B-213

STAIRS

1B-214

STOR.

D107

As indicated

M201


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 HEATING NEW

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346

KEY PLAN


As indicated

M300


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 VENTILATION DEMO

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346

KEY PLAN


DISHWASH

1B-110

VENDING

MACHINES

101

CORRIDOR

1B-101A

AUDITORIUM

B

B1-11B

COLLABORATORY

B1-12

MEETING

ROOM

B1-12A

CORRIDOR

C101

ECOLOGIZER

1B-110B

JANITORIAL

1B-110A

MEN'S WR

106A

WOMEN'S

WR

106B

STAIRS A

1B-213

STAIRS

1B-214

STOR.

D107

As indicated

M301


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 VENTILATION NEW

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346

KEY PLAN


DISHWASH

1B-110

VENDING

MACHINES

101

CORRIDOR

1B-101A

AUDITORIUM

B

B1-11B

COLLABORATORY

B1-12

MEETING

ROOM

B1-12A

CORRIDOR

C101

ECOLOGIZER

1B-110B

JANITORIAL

1B-110A

MEN'S WR

106A

WOMEN'S

WR

106B

STAIRS A

1B-213

STAIRS

1B-214

STOR.

D107

As indicated

M400


30 THE QUEENSWAY

TORONTO, ON M6R 1B5

LEVEL 1 FIRE PROTECTION

DEMO AND NEW

ISSUED/REVISED DATE








COUNTERSIGNED.

Project Number:

Drawn By:

Checked By:

Scale:


30 THE QUEENSWAY

TORONTO, ON M6R 1B5



2161346

KEY PLAN


St. Joseph’s Health Centre Learning Centre Revisions HHA #2161346-02

Section E-1Addenda E-1

Page 1 of 1

H.H. Angus and Associates

ADDENDA E-1

The information listed below is to form part of the Contract Documents. All associated costs are to

be included in Tender Price shown on Tender Form. Acknowledgment of this Addendum, by number, to be shown in space provided on Tender Form.

1 DRAWINGS

1.1 E000 – Electrical Legend and Drawing List (re-issued)


1.2 E100 – Electrical Demolition Plan (re-issued)


1.3 E200 – Electrical Lighting, Power and Systems Plan (re-issued)


1.4 E200B – Electrical Lighting, Power and Systems Plan – Alternate Lighting Option (Separate Price) (not issued)

.1 This drawing is the same as re-issued drawing E200 EXCEPT in Auditorium A and B, light fixture type ‘LA’ is a 2’x6’ version of the fixture in order to accommodate the 2’x6’ ACT ceiling type which shall be a separate price. Quantity of ‘LA’ light fixtures shall be the same as seen on re-issued drawing E200.

1.5 E300 – Electrical Details Sheet 1 and E300 – Electrical Details Sheet 2 (re-issued)

.1 Replace previously issued versions of these drawings with the copies attached herewith.

END OF ADDENDUM

END OF SECTION

Date post:	27-Apr-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times