Date post: | 16-Apr-2017 |
Category: |
Engineering |
Upload: | dhiraj-bhaskar |
View: | 334 times |
Download: | 23 times |
1. Lathe 2. Shaping 3. Milling 4. Drilling
Multi‐speed Gear Box of Machine Tool
Single input speed (Motor speed) = nem Multi‐Speeds on Spindle shaft (Spindle Speeds)
24/01/2017 2
n1 ,n2 ,n3 ,n4 n5 ,n6 ,n7 , nz
The extreme spindle speeds n1 = nmin nZ = nmax
Why Multi‐Speeds ?
24/01/2017 3
Different : • Feeds • W/P Materials • W/P Dimensions [D] • Cutting tool materials
n1 n2 n3 n4 n5 n6 n7 n8 N9= nz
nem
D.P.Bhaskar, Sanjivani COE Kopargaon
1 1
Speed Regulations
Stepped Regulations
Stepples Regulations
Discrete speed steps Continuous speed steps
24/01/2017 4
n1 n2 n3 n4 n5 nz
nem
D.P.Bhaskar, Sanjivani COE Kopargaon
Why Progressions *To find different speed steps *Find relation of two speed steps
1. Arithmetic progression (AP) 2. Geometric Progression (GP) 3. Harmonic Progression (HP)
Progression Laws
24/01/2017 5
Types of Progression Laws
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 6
24/01/2017 7
Difference between 2 successive speeds is constant = at at= (n2 – n1)= (n3– n2)= (n4 – n3)= (nz– nz‐1)
Z=Total speed steps (speeds) on spindle. (n1, n2, n3, n4,……………………….., nz‐1,nz..)
LAW
Ration of 2 successive Speeds= Ø=Speed Ratio
nmax =Maximum spindle speed (rpm)= nz nmin= Minimum spindle speed (rpm)= n1
n ( )
n1 =nmin
n2 =n1 + at n3 = n2 + at =n1 + 2at n4 = n3 + at =n1 + 3at nz = n(z‐1) + at =n1 + (z‐1)at
Dk = Diameters to be Machined at Specific cutting speed (v) =Upper limit of Diameter
∆
∆Dk = Diameters Range = (D2‐D1) = (D3‐D2) ………
24/01/2017 8
AP
Maximum spindle speed (rpm), nmax =445 rpm Minimum spindle speed (rpm), nmin=35 rpm Number of speed steps, Z=12 Cutting speed, v=20 m/min.
24/01/2017
9
D.P.Bhaskar, Sanjivani COE Kopargaon
Arithmetic progression
24/01/2017 10
Remarks @ AP
24/01/2017 11
At high spindle speeds, the diameter range is very narrow and hence some of the speed steps are redundant.
At low spindle speeds the diameter range is wide hence needs to add more speed steps between calculated values.
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 12
GP
D.P.Bhaskar, Sanjivani COE Kopargaon
Geometric progression
Range Ratio
24/01/2017 13
Geometric Progression Ratio
Speed Ratio
24/01/2017 14 D.P.Bhaskar, Sanjivani COE Kopargaon
Progression ratio/ Speed ratio Progression ratio/ Speed ratio
Geometric progression (also inaccurately known as a geometric series) is a sequence of speeds such that the ratio of any two successive speeds of the sequence is a constant called the Geometric progression ratio (speed ratio) of the sequence.
Range ratio
It ratio of maximum and minimum speed
GP
Maximum spindle speed (rpm), nmax =445 rpm Minimum spindle speed (rpm), nmin=35 rpm Number of speed steps, Z=12 Cutting speed, v=20 m/min.
24/01/2017 16
24/01/2017 17
Remarks @ AP
24/01/2017 18
At high spindle speeds, the diameter range is very narrow and hence some of the speed steps are redundant.
At low spindle speeds the diameter range is wide hence needs to add more speed steps between calculated values.
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 19
Variation in Diameters is wide in AP than GP
AP or GP?
GP gives Optimum Distribution Of Gear Speeds compared to
AP
AP – GP‐ HP Comparison AP – GP‐ HP Comparison
24/01/2017 21
Z Z N N
24/01/2017 22
24/01/2017 23
24/01/2017 24
24/01/2017 25
24/01/2017 26 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 27
24/01/2017 28
24/01/2017 29
Effect of GP ratio
24/01/2017 30
In gearbox design a set of preferred step ratio or preferred numbers is used to obtain the series of output speed of gearbox. The preferred step ratio is mentioned as basic series named as R5, R10,R20,R40 and R80. Each basic series has a specific step ratio. R [Charles Renard]
Definition of preferred number/speed series
24/01/2017 31
24/01/2017 32
Structural Formula
Structural Diagram
Ray Diagram
Speed chart
Gearing Diagram 1
2
3
4
5 Sequence
24/01/2017 33 D.P.Bhaskar, Sanjivani COE Kopargaon
Z =P1(x1)*P2(x2)*....Pu(xu) Structural Formula
The maximum number of speed that can be obtained from two shafts is three. Hence its necessary to use intermediate shafts between the input shaft and output shaft. The structural formula helps to arrive the number of stages and required gears to obtain the desired speeds.
Structural Formula
P : Speed steps/ Pairs in any stage X : Characteristic in stage
D.P.Bhaskar, Sanjivani COE Kopargaon
D.P.Bhaskar, Sanjivani COE Kopargaon
D.P.Bhaskar, Sanjivani COE Kopargaon
D.P.Bhaskar, Sanjivani COE Kopargaon
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 40
RULE
24/01/2017 41
HL=Z=6 VL=N+1=3
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 42
1) MAX Node addition=7.5 2) P of Stage one should be less
BEST
RULE
24/01/2017 43
BEST D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 44
Z=9
24/01/2017 45
Z=12
For More than 2 stages 1st and last stage P should be less BEST
RULE
24/01/2017 46
Optimum SF
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 47
24/01/2017 48 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 49 D.P.Bhaskar, Sanjivani COE Kopargaon
A ray diagram is a representation of structural formula. It provides information such as speed in each stage, the transmission ratio in each stage, The total number of speeds and its values.
Definition
Ray diagram for Z=4
24/01/2017 50 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 51
RULE
Ray Diagram Speed chart
24/01/2017 52
Ray Diagram Kinematic/Gearing Layout A kinematic layout is a pictorial representation of a gearbox, describing the arrangement of gears. It provides information like number of stages, number of shafts used, number of gear pairs and its arrangement.
Definition
24/01/2017 53
RULE
D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 54 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 55 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 56 D.P.Bhaskar, Sanjivani COE Kopargaon
24/01/2017 57
24/01/2017 58
Gearing Diagram
D.P.Bhaskar, Sanjivani COE Kopargaon
Z=12
24/01/2017 59
Gearing Diagram
Number of Teeth and Speed deviation diagram
Write best Structural formula, Draw Structural Diagram, Ray Diagram, Speed Chart, Gearing Diagram, No of teeth, Speed Deviation Diagram
D.P.Bhaskar, Sanjivani COE Kopargaon
Question
Sppeds n1 n2 n3 n4 n5 6 Calculated 100 158 252.8 395 632 995.4 Round off 100 160 250 400 630 1000
e
Ray Diagram, Speed Chart Gearing Diagram
Spindle speeds
Stage 1 No. Of Teeth Calculation Ray Diagram
No deviation in speeds in stage 1
ZA=20 ZA’=50 GA=2.5 ZB=27 ZB’=43 GB=1.59 C1=70
Stage 1 No. Of Teeth Calculation
D.P.Bhaskar, Sanjivani COE Kopargaon
Stage 2 No. Of Teeth Calculation
D.P.Bhaskar, Sanjivani COE Kopargaon
Ray Diagram
Deviation in speeds in stage 2 ZC=20 ZC’=80 GE=4 ZD=38 ZD’=61 GD=1.631 ZE=61 ZE’=39 GC=0.639 C2=100
Stage 2 No. Of Teeth Calculation
D.P.Bhaskar, Sanjivani COE Kopargaon
GE=4 GD=1.6 GC=0.635
GE=4 GD=1.631 GC=0.639
′′ ′ 400′ /GD=400/1.635=244.64
′ 630′ /GD=630/1.635=385.32
′′ ′ 400′ /GC=400/0.639=626
′ 630′ /GC=630/0.639=986
n(TH) n(PR) 100 100 160 160 250 244.64 400 385.32 630 626 100 986
Deviated Speeds
Speed Deviation ∆n
nth 100 160 250 400 630 1000 nact 100 160 244.64 385.32 4 986 ∆n 0 0 ‐2.144 ‐3.67 ‐0.639 ‐1.40
Limit for speed deviations ∆n < ± 10(ɸ‐1)٪ ∆n < ± 10(1.58‐1)=5.8٪
Speed Deviation Diagram
Difference between number of teeth on successive gears in change gear box
24/01/2017 70
•Input speed= 120 RPM •Draw structure diagram •Find Spindle speeds. •Speed trapped for given position •Speed ratio?
SPPU Questions
D.P.Bhaskar, Sanjivani COE Kopargaon
SPPU Questions
D.P.Bhaskar, Sanjivani COE Kopargaon
SPPU Questions
D.P.Bhaskar, Sanjivani COE Kopargaon
SPPU Questions
SPPU Questions
D.P.Bhaskar, Sanjivani COE Kopargaon