In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
Cutting edge Ø
M306MILLING SHANK type
.461" (11.7 mm)
F1
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M306.... 2.6.5T8EP T8PL
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Milling cutter shanks with damaged seating can be repaired by HORN.
For torque specifications of the screw, please see Technical Instructions.
Part number l1 d1 d
M306.0707.03A 100 6 7.5M306.1010.03A 120 6 10.0
In the UNITED STATES call us toll free1 - 888 - 818 HORN
with cylindrical shank for CNC-lathes
MILLING SHANK Type M306with through coolant supply
Picture = right hand cutting version
for use with Insert
Type
GROOVE MILLING / FACE MILLING
606
Cylindrical steel milling shank for collets
F2
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M306.ST1... 2.6.5T8EP T8PL
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Milling cutter shanks with damaged seating can be repaired by HORN.
For torque specifications of the screw, please see Technical Instructions.
Part number l1 d1 d
M306.ST10.01A 60 6 10M306.ST12.01A 70 6 12
In the UNITED STATES call us toll free1 - 888 - 818 HORN
GROOVE MILLING / FACE MILLING
MILLING SHANK Type M306.STno coolant supply
for use with Insert
Type 606
Picture = right hand cutting version
with cylindrical shank for CNC-lathes
Cylindrical steel milling shank for collets
F3
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TA45
AS
45
606.PLT6.08 .142 .126 .031 .461 Δ ▲
▲ on stock Δ 4 weeks P ● ●
● main recommendation M ● ●
ο alternative recommendation K ● ●
███ uncoated grades N ● ο
███ coated grades S ● ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
INSERT Type 606
FACE MILLING
for use with Milling shank
Type M306
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.126″Ds .461″
F4
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TA45
AS
45
606.0045.22 .138 .059 .008 .461 ▲
▲ on stock Δ 4 weeks P ●
● main recommendation M ●
ο alternative recommendation K ●
███ uncoated grades N ο
███ coated grades S ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
INSERT Type 606
for use with Milling shank
Type M306
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.059″Ds .461″
F5
F
In the UNITED STATES call us toll free1 - 888 - 818 HORN
F6
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
Cutting edge Ø
M311MILLING SHANK type
.697" (17.7 mm)
F7
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M311.001... 4.14T15P T15PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Milling cutter shanks with damaged seating can be repaired by HORN.
For torque specifications of the screw, please see Technical Instructions.
Part number l1 l2 d1 d
M311.0012.D.00A 80 7 9 12M311.0016.D.00A 80 7 9 16
In the UNITED STATES call us toll free1 - 888 - 818 HORN
with cylindrical shank for CNC-lathes
MILLING SHANK Type M311with through coolant supply
Picture = right hand cutting version
for use with Insert
Type
GROOVE MILLING / FACE MILLING
611
Cylindrical steel milling shank for collets
F8
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M311.ER2... 4.14T15P T15PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Clamping nut is not combined with milling shank - separate order required!
For torque specifications of the screw, please see Technical Instructions.
Part number l1 d1 d Clamping nut
M311.ER20.14.01 19.7 12.5 20 ER20.6499/ERM...M311.ER25.14.01 19.7 14.5 25 ER25.6499
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
MILLING SHANK Type M311.ERno coolant supply
for use with Insert
Type 611
Picture = right hand cutting version
with ER taper for CNC-lathes
Milling shanks for collet chucks DIN6499-A (8°) Ds 17.7 mm
F9
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TF45
611.PL61.62 .240 .224 .008 .697 ▲ ▲
▲ on stock Δ 4 weeks P ● ●
● main recommendation M ● ●
ο alternative recommendation K ● ●
███ uncoated grades N ● ●
███ coated grades S ● ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
INSERT Type 611
FACE MILLING
for use with Milling shank
Type M311
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.224″Ds .697″
F10
F
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
Cutting edge Ø
M313MILLING SHANK type
.854" (21.7 mm)
F11
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M313.00... 5.14T20P T20PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Milling cutter shanks with damaged seating can be repaired by HORN.
For torque specifications of the screw, please see Technical Instructions.
Part number l1 l2 d1 d
M313.0016.D.00A 80 7 11.3 16M313.0020.D.00A 80 7 11.3 20
In the UNITED STATES call us toll free1 - 888 - 818 HORN
with cylindrical shank for CNC-lathes
MILLING SHANK Type M313with through coolant supply
Picture = right hand cutting version
for use with Insert
Type
GROOVE MILLING / FACE MILLING
613713
Cylindrical steel milling shank for collets
F12
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M313.ER... 5.14T20P T20PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Clamping nut is not combined with milling shank - separate order required!
For torque specifications of the screw, please see Technical Instructions.
Part number l1 d1 d Clamping nut
M313.ER25.14.01 19.7 14 25 ER25.6499M313.ER32.14.01 19.7 14 32 ER32.6499
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
MILLING SHANK Type M313.ERno coolant supply
for use with Insert
Type 613713
Picture = right hand cutting version
with ER taper for CNC-lathes
Milling shanks for collet chucks DIN6499-A (8°) Ds 21.7 mm
F13
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TF45
613.PL61.62 .240 .224 .008 .854 ▲ ▲
▲ on stock Δ 4 weeks P ● ●
● main recommendation M ● ●
ο alternative recommendation K ● ●
███ uncoated grades N ● ●
███ coated grades S ● ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
INSERT Type 613
FACE MILLING
for use with Milling shank
Type M313
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.224″Ds .854″
F14
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TA45
AS
45
613.PLT6.15 .240 .224 .059 .854 Δ ▲
▲ on stock Δ 4 weeks P ● ●
● main recommendation M ● ●
ο alternative recommendation K ● ●
███ uncoated grades N ● ο
███ coated grades S ● ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
INSERT Type 613
for use with Milling shank
Type M313
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.224″Ds .854″
F15
F
This page has been electronically modified
Dimensions in inch Carbide grades
Part number s tmax r Z Ds
MG
12
TN35
TI25
TA45
AS
45
713.PL35.15.02 .232 .138 .008 12 .854 ▲
▲ on stock Δ 4 weeks P ●
● main recommendation M ●
ο alternative recommendation K ●
███ uncoated grades N ●
███ coated grades S ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
INSERT Type 713
for use with Milling shank
Type M313
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.138″Ds .854″
F17
F
In the UNITED STATES call us toll free1 - 888 - 818 HORN
Groove milling on brake caliperSimultaneous milling of two grooves with special insert type 314.Special design of the milling cutter body due to the form of the brake caliper. Because of the position of the inserts in the special milling heads type 380 it is not necessary to perform the cutting edges of the inserts with a chip divider.The shank shows a good antivibration resistance.Possible roundness of the machined grooves appr. .0008''Material: GGG40 (60-40-18)Cutting data:vc = 460 sfm vf3 = 5.1 ipm (cutter center) Milling cutter Ø 2.205'', Z = 3tg = 10.38 sec.
GROOVE MILLING by circular interpolation
Profile of groove
F18
F
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
Cutting edge Ø
M328MILLING SHANK type
1.091" (27.7 mm)
F19
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M328.00... 5.14T20P T20PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Milling cutter shanks with damaged seating can be repaired by HORN.
For torque specifications of the screw, please see Technical Instructions.
Part number l1 l2 d1 d
M328.0016.D.00A 80 7 14.3 16M328.0020.D.00A 80 7 14.3 20
In the UNITED STATES call us toll free1 - 888 - 818 HORN
with cylindrical shank for CNC-lathes
MILLING SHANK Type M328with through coolant supply
Picture = right hand cutting version
for use with Insert
Type
GROOVE MILLING / FACE MILLING
628
Cylindrical steel milling shank for collets
F20
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M328.ER... 5.14T20P T20PQ
Further sizes upon request Ds see inserts Dimensions in mm
Ordering note:Clamping nut is not combined with milling shank - separate order required!
For torque specifications of the screw, please see Technical Instructions.
Part number l1 d1 d Clamping nut
M328.ER25.16.01 21.7 15 25 ER25.6499M328.ER32.16.01 21.7 20 32 ER32.6499
In the UNITED STATES call us toll free1 - 888 - 818 HORN
FACE MILLING
MILLING SHANK Type M328.ERno coolant supply
for use with Insert
Type 628
Picture = right hand cutting version
with ER taper for CNC-lathes
Milling shanks for collet chucks DIN6499-A (8°) Ds 27.7 mm
F21
F
Dimensions in inch Carbide grades
Part number s tmax r Ds
MG
12
TN35
TI25
TF45
628.PL61.62 .240 .224 .008 1.091 ▲ ▲
▲ on stock Δ 4 weeks P ● ●
● main recommendation M ● ●
ο alternative recommendation K ● ●
███ uncoated grades N ● ●
███ coated grades S ● ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
INSERT Type 628
FACE MILLING
for use with Milling shank
Type M328
Picture = right hand cutting version
Depth of cut up toCutting edge Ø
.224″Ds 1.091″
F22
F
Spare parts
Milling shank Screw TORX PLUS® Wrench
M275.031.D25.3.04A 3.5.10.T10P T10PL
Further sizes upon request w and tmax see inserts Dimensions in mm
For torque specifications of the screw, please see Technical Instructions.
Part number Z Ds l1 d
M275.031.D25.3.04A 4 31 125 25
In the UNITED STATES call us toll free1 - 888 - 818 HORN
GROOVE MILLING / FACE MILLING
MILLING SHANK Type M275with through coolant supply
for use with Indexable insert
Type S275
Picture = right hand cutting version
Material of shank: Steel (not recommended for shrink fitting)
Cutting edge Ø Ds 1.220″ (31 mm)
F23
F
Spare parts
Screw-in cutter Screw TORX PLUS® Wrench
M275.03... 3.5.10.T10P T10PL
Further sizes upon request w and tmax see inserts Dimensions in mm
For torque specifications of the screw, please see Technical Instructions.
Part number Z Ds l1 l2 d1 d4 SW
M275.031.M16.1.04 4 31 45 22 25 29 24M275.036.M16.1.04 4 36 45 22 30 29 27
In the UNITED STATES call us toll free1 - 888 - 818 HORN
Material of shank: Steel
SCREW-IN CUTTER Type M275with through coolant supply
Picture = right hand cutting version
for use with Indexable insert
Type
GROOVE MILLING / FACE MILLING
S275
Cutting edge Ø Ds 31 / 36 mm
F24
F
Spare parts
Milling cutter Screw Screw TORX PLUS® Wrench Washer
M275.0038.A16.05 DIN912-M8x25 3.5.10.T10P T10PL 020.0813.3438M275.0048.A22.08 DIN912-M10x25 3.5.10.T10P T10PL DIN433-10.5-StM275.0058.A27.10 DIN912-M12x30 3.5.10.T10P T10PL DIN433-13-StM275.0078.A32.14 DIN7984-M16x35 3.5.10.T10P T10PL DIN433-17-St
Further sizes upon request w and tmax see inserts Dimensions in mm
For torque specifications of the screw, please see Technical Instructions.
Part number Z Ds h h2 d2 d3 d4 d5 l1 l2 s p
M275.0038.A16.05 5 38 33.0 32.7 32.0 16 32.0 13.5 18 22.7 8.4 5.6M275.0048.A22.08 8 48 37.0 36.7 40.5 22 40.5 18.5 20 24.7 10.4 6.3M275.0058.A27.10 10 58 42.5 42.2 50.0 27 48.0 22.0 22 27.2 12.4 7.0M275.0078.A32.14 14 78 50.0 49.7 3.5 32 58.0 33.0 25 36.7 14.4 8.0
In the UNITED STATES call us toll free1 - 888 - 818 HORN
GROOVE MILLING / FACE MILLING
MILLING CUTTER Type M275with through coolant supply
for use with Indexable insert
Type S275
Picture = right hand cutting version
Cutterhole and cross keyway as per DIN 138
Cutting edge Ø Ds 38/48/58/78 mm
F25
F
Dimensions in mm Carbide grades
Part number s tmax r
MG
12
TN35
TI25
TA45
AS
45
RS275.PL43.52 .169 .157 .008 ▲
▲ on stock Δ 4 weeks P ●
● main recommendation M ●
ο alternative recommendation K ●
███ uncoated grades N ο
███ coated grades S ●
███ brazed/Cermet H
In the UNITED STATES call us toll free1 - 888 - 818 HORN
INDEXABLE INSERT Type RS275
FACE MILLING
for use with Milling shank
Type M275
R = right hand version shown
Depth of cut up to .157″
F26
F