Date post: | 27-Jun-2015 |
Category: |
Technology |
Upload: | maxon-data-communications |
View: | 37 times |
Download: | 1 times |
Turn your Smartmax M2M HSPA Smart Modem Solution into a cost-effective mini RTU with the I/O Interface Controller. When used in conjunction with Maxon’s Smartmax Modem for data telemetry,
the I/O Interface Controller provides wide-ranging flexibility for system integrators and users for automating and controlling innumerable field applications.
Local or remote programming of the I/O Interface Controller can be done via the Smartmax’s built-in Web Interface. The fully featured web interface includes programming of the DNP3 settings and
I/O status updates via SMS.
The SmartMax connects directly to the IO board via a ribbon connection, while the I/O controller can be wired to collect data automatically and connect directly to sensors, meters, loggers or
process equipment.
0811
12
TRANSFORM THE SMARTMAX INTO A POWERFUL COST-EFFECTIVE MINI REMOTE TERMINAL UNIT
Smartmax I/O Board Features• 6 Digital Inputs (1 configurable as pulse input)
• 2 Analogue Inputs
• 4 Digital Outputs
• 1 Pulse Input • DNP3/SMS Settings configurable via web page inside Smartmax Modem.
• I/O Board controllable via DNP3, SMS, or using inbuilt web page. • SDK (Software Development Kit) is available for the Smartmax HSPA Modem (Product Code: MA-2010)
* Not
to s
cale
CHOOSE WELL... CHOOSE WISELY... CHOOSE MAXON...
M2M HSPA Smart Modem Solution - I/O Board: MA-4020
The Mini I/O Controller MA-3020 is a fully labelled , robust enclosure that secures the I/O Board. This solution provides an all-in-one product.
www.maxon.com.au
Metering
Water
Road Signs
Power
Security
Transport
M2M HSPA Smart Modem Solution - I/O Board: MA-4020
T | +612 8707 3000 F | +612 8707 3001 E | [email protected] 36A Gibson Avenue, Padstow NSW Austral ia 2211 www.maxon.com.au
Environmental Specifications• Normal Operation Temperature -20 to 60° C
• Extreme Operation Temperature -25 to 75° C
Connections• 6 x Digital Inputs (INPUT 0 ~ INPUT 5 in terminal block)
• 4 x Digital Outputs (OUTPUT 0 ~ OUTPUT 3 in terminal block)
• 2 x Analog Inputs (ANALOG 0 and ANALOG 1)
• 1 x Pulse Input (INPUT 0)
• 1 x Case Open
• 1 x Battery (Monitor Battery Level)
• 1 x 20 Pin Terminal Block (SmartMax Interface)
Compliance• RoHS Compliant
Frequency Bands• WCDMA/HSPA 850MHz, 900MHz, 1900MHz, 2100MHz
• GSM/GPRS/EDGE 850MHz, 900MHz, 1800MHz and 1900MHz
General Features• Packet Data
• 2 Way SMS
• Remote SMS diagnostics & reset
• Embedded TCP/IP, UDP/IP STACK
• In-built periodic reset
• External DC Powered
• Support VPN Server and Client Mode
• Dynamic DNS
• Supports DNP3 (Outstation) using extension I/O board
• Rugged Metal Casing for industrial use
• In-Built Web Interface
• Programmable scheduler to control WAN connection
• Telnet support
• Save and restore modem configuration from a file
• FOTA - Firmware upgrade over the air
• External antenna connectivity to maximise HSPA coverage
• External LED to show Network and Connection status
Dimensions• 210mm X 1100mm X 650mm (with connectors)
Connection Specifications6 Digital Inputs Characteristics
· VIH (Input voltage high range): 2 ~ 24V
· VIL (Input voltage low range): -2 ~ 0.8V
· Ri (Input impedance): more than 5 kΩ
· Rd (Internal pull-up): 47 kΩ for short to ground detection
· Input chatters are filtered by S/W setting
1 Pulse at Input 0
· Frequency range 0 ~ 1000 Hz
· Accuracy (25°C) 0.05 % of span
· Temperature stability 0.005 % / °C
· Input impedance 47kΩ
4 Digital Outputs
· MOSFET switch to ground
· Ro (Output resistance): less than 300 m Ω
· VOpen (maximum allowed output voltage on open): 24 VDC
· IOut (maximum allowed switching current to ground): 1A
· Switching time < 10 msec
· Chatter free
2 Analog Inputs
· 12bit resolution
· Accuracy: Typical ±0.25% ; Worst Case ±1%
· Maximum sampling rate: 10 sample/sec
· Input signal type: one of 0~20mA, 0~5V, or 0~10V
· (The input type is selected by the jumper “PULSE” on the connected Smartmax and INPUT# on the I/O board)
· Input impedance for the signal type 0 ~ 20mA < 100Ω
· Input impedance for the signal type 0 ~ 10VDC > 10K Ω