* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
CONTACTDE CAPOT
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed. Notice: l'installation des éléments de sécurité est obligatoire. Le contact de capot est un élément de sécurité essentiel et doit absolument être installé.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
STATUT DE CAPOT : LE CONTACT DE CAPOT, DOIT ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT, PROGRAMMEZ LA FONCTION A11 À NON.
A11 OFFNON
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20210426
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)
VEHICLEVEHICULES
YEARS ANNÉES Im
mob
ilize
r byp
ass
Con
tour
nem
ent
d’im
mob
ilisa
teur
Lock
Unl
ock
Arm
Dis
arm
RA
P D
isab
le
Trun
k R
elea
se
Park
ing
Ligh
ts
Tach
omet
er
Doo
r Sta
tus
Trun
k S
tatu
s
Hoo
d S
tatu
s*
Han
d-B
rake
Sta
tus
Foot
-Bra
ke S
tatu
s
OEM
Rem
ote
mon
itorin
g
R.S
. OEM
rem
ote
Sta
nd A
lone
com
patib
le
FORDEscape 80-BITS 2013-2016 • • • • • • • • • • • • • • • •C-MAX hybrid 80-BITS 2013-2016 • • • • • • • • • • • • • • • •Kuga 80-BITS 2013-2015 • • • • • • • • • • • • • • • •Transit Connect 80-BITS 2014-2016 • • • • • • • • • • • • • • • •
T-HARNESS FORD KEY 80-BITST- HARNAIS POUR FORD KEY 80-BITS
ADDENDUM - SUGGESTED WIRING CONFIGURATION ADDENDUM - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))
1x Diode 1 Amp Diodes 1 Amp
2x Diode 3 Amp Diodes 3 Amp
1x Fusible 10 AMp Fusible 10 AMp
Guide # 32851
Program bypass option(Vehicle hybrid only):
Programmez l’option du contournement(vehicule hybride seulement):
UNIT OPTIONOPTION UNITE DESCRIPTION
D4 Hybrid mode (Vehicle hybrid only)Mode hybride (vehicule hybride seulement)
FIRMWARE VERSIONVERSION LOGICIELLE To add the firmware version and the options, use the FLASH LINK
UPDATER or FLASH LINK MOBILE tool, sold separately.Pour ajouter la version logicielle et les options,
utilisez l’outil FLASH LINK UPDATER ou FLASH LINK MOBILE, vendu séparément.
71.[52] MINIMUM
Program bypass option IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:Programmez l’option du contournement
SI LE VÉHICULE N’EST PAS ÉQUIPÉ D’UN CONTACT DE CAPOT FONCTIONNEL:
UNIT OPTIONOPTION UNITE DESCRIPTION
A11 OFFNON
Hood trigger (Output Status).
Contact de capot (état de sortie).
Page 1 / 10
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
COUPEZCUTDOOR SIDE
CÔTÉ PORTEBCM SIDECÔTÉ BCM
OVolt 12Volt
RAP / Factory Alarm Control
Multimeter voltage test (MODULE NOT CONNECTED).À l'aide d'un multimetre testez le voltage. (MODULE NON CONNECTÉ)
A17 A18
Driver Door Pin
BCM SIDECÔTÉ BCM
DOOR SIDECÔTÉ PORTE
Harness under passenger-side carpet.Harnais sous le tapis côté passager
RX and TX of the module RX et TX du module
OBD-II connector
At ignition barrelAu barillet d'ignition
Connecteur OBD-II
Driver kick panelPanneau latéral côtéconducteur
Immobiliserimmobilisateur
BCM, Fuse box, behind glove boxBCM, Boîte à fusibles, sous lecoffre à gants
(+)12V
Module (-)LockSignal
(+)Parking Lights right
(+)Parking Lights leftPurple/GreenMauve/Vert
Purple/GreenMauve/Vert
EscapeKuga
Yellow/BlueJaune/Bleu
Brown/YellowBrun/Jaune
Transit Connect
Purple/GreenMauve/Vert
Purple/GreenMauve/Vert
C-MAX
Module (-)Unlock SignalPurple/OrangeMauve/Orange
EscapeKuga
Purple/GrayMauve/Gris
C-MAXTransit Connect
(-)Trunk release
BrownBrun
Yellow/OrangeJaune/Orange
BrownBrun
CAN HIGH
CAN LOW
Page 2 / 10
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTIONNOTE
T-HARNESS INSTALLATION | INSTALLATION DU T-HARNAIS
Ignition barrelBarillet d'ignition
ImmobilizerImmobilisateur
See nextpageVoir page suivante
12V BATTERY 12V BATTERIEATTENTION LE COURANT DU 12V PROVENANT DU HARNAIS-EN-T EST LIMITÉ À 5 AMPÈRES MAXIMUM.
Si les lumières de stationnement (+) requièrent plus de 5 Ampères, branchez le 12V du démarreur à distance directement à la batterie du véhicule avec le fusible approprié.
Certains démarreurs à distance NE peuvent PAS être allimentés par le Data-Link. Dans ce cas, branchez le 12V (avec fusible) du démarreur à distance directement au harnais-en-T.
ATTENTION THE T-HARNESS CURRENT IS LIMITED AT 5 AMP MAXIMUM.
If the parking lights (+) require more than 5Amp. connect the remote-starter's power directly to the vehicles battery with the appropriate fuse.
Some remote starters can not be powered through Data-Link. In these cases connect the remote starter's fused 12V power wire directly to the T-Harness.
Make the connection between the UNIT and the T-HARNESSEffectuez les branchements entre le MODULE et le HARNAIS EN T.
Yellow/BlackYellowLt.Blue/BlackLt.Blue
Page 3 / 10
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
RedRouge
(+)12VCAN LOW
CAN HIGH
1
9 10
2 3 4 5 7 8
11 12 13 14 15 16
6
11
3 6
Viol
et/O
rang
eVi
olet
/Ora
nge
Gray
/Ora
nge
Gris/
Ora
nge
1
9 10
2 3 4 5 7 8
11 12 13 14 15 16
6
11
3 6
OBD-II connectorFront view
Connecteur OBD-II Vue de face
Harness from passenger carpetHarnais provenant de sous le
tapis côté passager
BCM At Fuse box behind glove box, Big 2 pins
connector.À la boîte à fusibles, gros
connecteur 2-pins.
(+)Parking Lights right
(+)Parking Lights left
1
2
Harness from Driver kick panelHarnais provenant du panneau latéral
côté conducteur
(-)Unlock
CUT
(-)Lock Gray/YellowGris/Jaune
A17 A18
A19
OVolt 4-5Volt
1 Connection required to arm the factory alarm when the doors are locked and RAP Control. 1 Branchement requis pour armer l'alarme d'origine lorsque les portes sont verrouillées et pour le contrôle du RAP.
C3 C4Driver door1
Green/PurpleVert/Mauve
BCM sideCôté BCM
Door sideCôté porte
Purple/Orange*Mauve/Orange*
Yellow/Blue*Jaune/Bleu*
Brown/Yellow*Brun/Jaune*
(-)Trunk releaseYellow/Orange*Jaune/Orange*
20 PIN CONN.Use the connector supplied with the unit.Utilisez le connecteur fourni avec le module.
DNOT CONNECTED | NE PAS BRANCHER
C
5 PIN CONN.Use the connector supplied with the unit.Utilisez le connecteur fourni avec le module.
A10
A20
SEE PREVIOUS PAGE
VOIR PAGE PRÉCÉDENTE
B
A
MAKE THE CONNECTIONS I FAIRE LES BRANCHEMENTSNOT CONNECTED | NE PAS BRANCHER
A1/RS6/A16
1Am
p D
iode
ALWAYS REQUIREDTOUJOURS REQUIS
NOT REQUIRED WITH DATALINKNON REQUIS EN DATA-LINK
REMOTESTARTER
DÉMARREURÀ DISTANCE
WITH | AVEC DATA-LINK:Direct connectionBranchement directe
Cut | Coupez RedBlack
BlueWhite
B4B3B2B1
Cut | Coupez
BlackRed 12V BATTERY
GroundB4B3
SEE | VOIR NOTE PREVIEWS PAGE
PAGE PRÉCÉDENTE
IN RS9 IN RS9
OUT RS10 IN RS12 IN RS13
OUT RS14
IN RS16OUT RS17OUT RS18 Ground | Masse (-)RS1
12V BATTERYRS2 IN (+)PARKING LIGHTSRS3 OUT (-)PARKING LIGHTSRS4 OUT (+)
ACCESSORYRS5 OUT (+)IGNITIONRS6 OUT (+)IGNITION2RS7 OUT (+)
1
STARTRS8 OUT (+)START2RS8b OUT (+)
a 1
WITH DATA-LINK:AVEC DATA-LINK:
WITH D2D:AVEC D2D:
OROU
3Am
p D
iode
3Am
p D
iode
10 AmpFuse
WITHOUT DATA-LINK:SANS DATA-LINK:
RS2
RS4
RS10
GROUND OUT WHILE RUNNING
LOCKUNLOCKDOOR
TACHOMETERFOOT BRAKE
TRUNK RELEASEHAND BRAKE
(-)
(-)(-)(-)
(+)(+/-)(-)
A12A11
A4A3A2
A8
(-)A14HOOD(-)A15
A5
* See page 2 for the colors* Voir la page 2 pour les couleurs
(+) Key sense Yellow In A1(-) Lock Purple In A2
(-) Unlock Purple/White In A3(-) Door/Trunk Status Green Out A4
(-) Unlock White Out A5Orange In A6
Orange/Black In A7(-) Ground While Running Dk.Blue In A8
(+)Start Red/Blue In A9RX Lt.Blue/Black A10
(+) Foot Brake Status Black Out A11(-/+) Tachometer Pink Out A12
Yellow/Black In A13(-) Hand Brake Status Brown/White Out A14
(-) Hood Status Pink/Black Out A15(+) Key sense Purple/Yellow A16
Driver Door Pin Green/White A17Driver Door Pin Green/Red A18
(-) Lock signal White/Black A19TX Lt.Blue A20
C5 BrownC4 Gray/Black CAN LOWC3 Gray CAN HIGHC2 Orange/BrownC1 Orange/Green
D6 White/RedD5 White/BlueD4 White/GreenD3 Yellow/RedD2 Yellow/BlueD1 Yellow/Green
WIRING CONNECTION | SCHÉMA DE BRANCHEMENT
THAR-FOR1
Lt.Blue
Yellow/Black
Lt.Blue/Black
Yellow
Page 4 / 10
LO
CK
ACC ON
PUSH
STA
RT
IGN
TURNON/RUN
Wait 3 seconds.
LO
CK
ACC ON
STA
RT
IGNON
WAIT3 SEC.
Attendre 3 secondes.
LO
CK
ACC ON
PUSH
STA
RT
OFFTURNOFF
LO
CK
ACC ON
STA
RT
PUSHPUSH
REMOVEKEY
5
KEY#1CLÉ#1
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION
KEY#2CLÉ#2
KEY#1CLÉ#1
2 KEY REQUIRED2 CLÉS REQUISES
Choose between : Choisir entre:
KEY#1CLÉ#1
KEY#2CLÉ#2
KEY#1CLÉ#1
2 key programming.Programmation avec 2 clés.
DCRYPTOR and 1 key programming.Programmation avec DCRYPTOR et 1 clé.
RELEASE
Release the programming button when the LED is RED.
If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.
Insert the required remaining connectors.
CETTE PROGRAMMATION EST POUR LES FORD 40BITS
1
2
3
ONREDROUGE
Insérez les connecteurs requis restants.
Relâchez le bouton de programmation quand la DEL est ROUGE.
Si le DEL n'est pas ROUGE solide débranchez le connecteur 4 pins (Data-Link) et allez à l'étape 1.
ALLE O ALL
Press and hold the programming button:Connect the 4-PIN Data-link harness (Black connector).
� The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
Appuyez et maintenir enfoncé le bouton de programmation: Branchez le harnais Data-Link à 4-Broches (connecteur Noir)
� Les DELs Bleue, Rouge, Jaune et Bleue & Rouge s'allumeront alternativement.
Tournez la première clé fonctionelle à Ignition.
Turn the first functional key to the Ignition ON/RUN position.
Turn the key to the OFF position.
Remove the first key.
Tournez la clé à la position Arrêt (OFF).
Retirez la clé du contact.
xx11HOLD
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
4
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 1/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 1/2
Release the programming button when the LED are BLUE & RED.
Si le DEL ne sont pas BLEU et ROUGE débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1.
ONBLUE BLEU
ONREDROUGE
Relâchez le bouton de programmation quand les DELs sont BLEU et ROUGE.
If the LED are not solid BLUE and RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.
RELEASE
Page 5 / 10
8
Press and hold theprogramming button untilthe vehicle ignition turnON.
Pesez et garder appuyéle bouton deprogrammation jusqu'à ceque l'ignition du véhicules'allume.
Release theprogramming button.
Relâchez le bouton deprogrammation.
Ignition ON
The RED and BLUE LEDSwill flash rapidly 10x times.
The BLUE LED will flashrapidly.CAN-Bus programmed.
Les DELS ROUGE et BLEUEclignoteront 10x fois rapidement.
La DEL BLEU clignoterarapidement:Réseau CAN programmé
6
7
5 sec. max
CAUTION The following step mustbe completed within 5 seconds.Otherwise disconnect all connectorsand go back to step 1.
ATTENTION5 secondes.
débranchez allez
les prochaines étapes doivent êtrecomplétées en moins deSi non, tous les connecteurs età l'étape 1.
x1PRESS
RELEASE
HOLD
Wait 3 seconds. Attendre 3 secondes.
The module is nowprogrammed.
Le module estprogrammé.
Use the remote of the remotestarter or security system to testall of the supported features toensure proper programming.
Testez toutes les fonctionssupportées sur le véhicule avec latélécommande du démarreur àdistance ou du système de sécurité.
The vehicle ignition willturn OFF.
L'ignition du véhicules'éteins.
Ignition OFF
If the LED is solid REDdisconnect the 4 Pinconnector (Data-Link) and goback to step 1.
Si le DEL est ROUGE solidedébranchez le connecteur 4pins (Data-Link) et allez àl'étape 1.
FLASH 10XIGNITION ON
FLASH 10X
FLASH 10X
FLASH
LOCK
ACC ON
PUSH
START
IGN
KEY#2CLÉ#2
LOCK
ACC ON
START
IGNON.
TURNON/RUN WAIT
3 SEC
LOCK
ACC ON
PUSH
START
OFF
LOCK
ACC ON
START
PUSHPUSH
FTURNOF
REMOVEKEY
Tournez la deuxièmeclé fonctionelle à Ignition.
Turn the second functionalkey to the Ignition ON/RUNposition.
Turn
Remove
the key to the OFFposition.
the second key.
Tournez
Retirez
la clé à laposition Arrêt (OFF)
la deuxième clédu barillet d'alimentation.
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/2 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/2Page 6 / 10
x1HOLD
4
Press and release the programming button once (1x).x1
PRESS
Appuyez et relâchez 1 fois le bouton de programmation.
The RED LED will flash once. La DEL ROUGE clignote 1 fois.
OFF
ON
PRESS X1
OFF
ON
ON
5
The RED LED will turn OFF.
The YELLOW LED will turn on.
La
DEL ROUGE s'éteint.
La DEL JAUNE s'allume.
LOCK
ACC ON
PUSH
START
IGNONIGN IGNITION OFF IGNITION ON
OFFON
ON
Tournez la clé à Ignition.Turn the key to the Ignition ON/RUN position.
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
1
2
3
The Blue, Yellow, Red and Blue & Red LEDs will alternativelyilluminate.
Les DELs Bleue, Jaune, Rouge et Bleue & Rougeillumineront alternativement.
Release the programming button when the LED is RED.
Insert the required remaining connectors.
Insérez les connecteurs requis restants.
Relâchez le bouton de programmation quand la DEL est ROUGE.
LED may differ depending on the module casing.L’apparence des DELS peut différer selon le boîtier du module.
RELEASE
ON REDROUGE
Si la DEL n’est pas ROUGE débranchez le connecteur 4 pins (Data-Link) et allez au début de l'étape 1.
If the LED is not solid RED disconnect the 4-Pin connector (Data-Link) and go back to step 1.
Press and hold
Insert
theprogramming button:
the 4-Pin (Data-Link)connector.
Appuyez maintenirenfoncé
Insérez
etle bouton de
programmation:le connecteur 4 pins
(Data-Link)
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTOR
Parts required (not included) Pièces requises (non incluses)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
1x FLASH LINK MOBILE1x FLASH LINK MOBILE APP
SOFTWARE | PROGRAMME Smartphone Android or iOS with Internet connection (Internet provider charges may apply)Téléphone Intelligent Android ou iOS avec connection Internet (des frais du fournisseur Internet peuvent s’appliquer)
OROU
Microsoft Windows Computer with Internet connectionOrdinateur Microsoft Windows avec connection Internet1x 1x
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. | AVANT LA PROGRAMMATION CONFIGURER LES OPTIONS DE L'UNITÉ ET SAUVEGARDER.
Page 7 / 10
7
The RED LED will turn OFF.
The YELLOW LED will turn on.
La
DEL ROUGE s'éteint.
La DEL JAUNE s'allume.
LOCK
ACC ON
PUSH
START
IGNONIGN IGNITION OFF IGNITION ON
OFFON
ON
Tournez la clé à Ignition.Turn the key to the Ignition ON/RUN position.
6
LOCK
ACC ON
PUSH
START
OFFOFF
IGNIGNITION ON IGNITION OFF
ON OFF
The YELLOW LED will turn OFF.
The RED LED will turn on.
La
DEL JAUNE s'éteint.
La DEL ROUGE s'allume.ON
Turn the key to the OFF position.
Fermez la clé de contact.
8
LOCK
ACC ON
PUSH
START
OFFOFF
IGNIGNITION ON IGNITION OFF
ON OFF
The YELLOW LED will turn OFF.
The RED LED will turn on.
La
DEL JAUNE s'éteint.
La DEL ROUGE s'allume.ON
Turn the key to the OFF position.
Fermez la clé de contact.
LOCK
ACC ON
PUSH
START
IGN
TURNON/RUN
LOCK
ACC ON
PUSH
START
OFFF
TURNOF
10
9
The RED and YELLOW LEDswill alternate.
La DEL ROUGE et JAUNEalternent.
The YELLOW LED will turnon and off.
The RED LED will turn OFF.
La
La DEL JAUNE s'allume ets’éteint.
DEL ROUGE s'éteint.
WAIT, the BLUE LED to flashrapidly.
ATTENDRE que la DELBLEUE clignote rapidement.
Tournez la clé à Ignition.Turn the key to theIgnition ON/RUN position.
Turn the key to theOFF position.
Tournez la clé à laposition Arrêt (OFF).
IGNITION OFF
ONON
FLASH RAPIDLY
OFF
FLASH
IGNITION OFF IGNITION ON
OFFON
ON
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/3Page 8 / 10
This guide may change without notice. See www.fortin.ca for latest version.Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 3/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 3/3
EVO-ALL
Disconnect all the connectors and after the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite le connecteur Data-Link (4-pins).
*Pièces requises (non incluses)
Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILEto visit the DCryptor menu.
Utilisez l'outil: FLASH LINK UPDATER ou FLASH LINK MOBILEpour visiter le menu DCryptor.
*Parts required (not included)
FLASH LINK UPDATER*
FLASH LINK MOBILE*
FLASH LINK MANAGER*SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection*
Ordinateur Microsoft Windows avec connection Internet*
VEHICLE'S OBDII CONNECTOR
CONNECTEUR OBDII DU VÉHICULE
OROU
Smartphone* (Internet provider chargesmay apply)Téléphone Intelligent* (des frais du fournisseurInternet peuvent s’appliquer)
AFTER DCRYPTOR PROGRAMMING COMPLETEDGo back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION DCRYPTOR COMPLETÉE : retournez au véhicule etrebranchez le connecteur 4-pins (Data-Link) et après, tous les connecteurs du EVO-ALL.
EVO-ALL
11
12
13
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE | PROCÉDURE DE VÉRIFICATION DU DÉMARREUR À DISTANCE / ALARMETest the remote starter. Remote start the vehicle.Testez le démarreur à distance. Démarrez le véhicule à distance.
The module is now programmed.Le module est programmé.
Page 9 / 10
ALL
Service No : 000 102 04 2536
Date: xx-xx
INTERFACE MODULE
Made in CanadaPATENTS PENDING US: 2007-228827-A1
www.fortinbypass.com
HARDWARE VERSION FIRMWARE VERSION
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation GuidesUpdated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installationsDes mises à jour du Firmware (microprogramme) et des guides d’installation sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNINGThe information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les fi ls et circuits avant d’effectuer les connexions. Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module, excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORTTél: 514-255-HELP (4357) 1-877-336-7797
ADDENDUM GUIDEWEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
EVO-ALL
Page 10 / 10