Pressure-39 Pressure-39 Model 1151 Model 1151 Alphaline ® Pressure Transmitters FEATURES • A complete family of transmitters • Ranges from 0–0.5 inH 2 0 to 6,000 psig (1.24 kPa to 41370 kPa) • Solid-state, plug-in circuit boards • Compact, rugged construction impervious to vibration • Local span and zero adjustments • Modular construction • Adjustable damping • Numerous options to permit greater application flexibility • Smart, analog, or low-power electronics
Transcript
Mod
el 1
151
Model 1151 Alphaline®
Pressure Transmitters
Pressure-39
FEATURES• A complete family of
transmitters
• Ranges from 0–0.5 inH20 to 6,000 psig(1.24 kPa to 41370 kPa)
• Solid-state, plug-in circuit boards
• Compact, rugged constructionimpervious to vibration
• Local span and zero adjustments
• Modular construction
• Adjustable damping
• Numerous options to permit greater application flexibility
• Smart, analog, or low-power electronics
Pressure-39
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
1151
–014
2A
INTRODUCTIONThis product data sheet highlights Rosemount®
Model 1151 differential, absolute, gage, and high-line pressure differential transmitter features and options. For information about the draft range, liquid level transmitters, transmitters with remote seals, and additional information on smart transmitters, refer to their respective data sheets referenced on the back page of this data sheet.
INDUSTRY-LEADING PERFORMANCE AND FEATURES
The Model 1151 Alphaline® series of pressure transmitters brings true precision to the measurement of flow, level, gage and absolute pressures, vacuum, and specific gravity. Direct electronic sensing with the completely sealed δ-cell (delta-cell) capacitance sensing element allows significant improvement and stability in pressure measurements. Welded stress isolation clamping in the sensor housing prevents introduction of errors caused by stresses and torques on the process flanges and minimizes effects of line pressure and overpressure.
Installation, calibration, and commissioning are simplified by compact design, integral junction box, and local span and zero adjustments.
The housing features an explosion-proof, weather-proof construction with separate compartments for the electronics and wiring connections. For most models, 316L SST, Hastelloy® C, Monel®, gold-plated Monel, or tantalum materials are available for corrosive service. Modular construction and plug-in printed circuit boards aid in trouble-shooting and reduce parts stocking.
APPLICATIONSModel 1151 Pressure Transmitters are available in
a variety of configurations for differential, flow, gage, absolute, vacuum, liquid level, and specific gravity measurement applications. The transmitter model number, determined from the ordering information tables, specifies available features such as pressure ranges, outputs, and materials of construction that are basic to each transmitter. Additional options, such as accessories, certifications, and special manufacturing procedures are also available.
re-40
OPERATIONDuring operation, the isolating diaphragms and
fill fluid on the high and low sides transmit the process pressure to the oil fill fluid. The fluid in turn transmits the process pressure to a sensing dia-phragm in the center of the d-cell sensor. The sensing diaphragm functions as a stretched spring element that deflects in response to differential pressure across it (in GP transmitters, atmospheric pressure is transmitted in a like manner to the low side of the sensing diaphragm). In AP transmitters, a reference pressure is maintained on the low side. The displacement of the sensing diaphragm, a maximum movement of 0.004 in. (0.10 mm), is proportional to the pressure. Capacitor plates on both sides detect the position of the sensing diaphragm. The differential capacitance between the sensing diaphragm and the capacitor plates is converted electronically to an appropriate current, voltage, or digital HART® (Highway Addressable Remote Transducer) output signal.
Capaci tor Pl ates
Lead Wires
Sensing Diaphragm
Rigid Insulation
Oil Fill
Isolating Diaphragm Welded Seals
FIGURE 1. Cross Section of the Rosemount d-Cell™ Sensor.
MODEL 1151HP DIFFERENTIAL PRESSURE TRANSMITTER FOR HIGH LINE PRESSURES
• Superior performance: 0.1% accuracy, 15:1 rangeability
• Differential pressures from 30 inH2O to 1,000 psi (7.5 to 6895 kPa)
• Provides accurate differential pressure measurements to 4,500 psi (31026 kPa)
• Silicone and inert fill fluid• Modular construction, adjustable damping,
and local span and zero adjustments
MODEL 1151LT FLANGE-MOUNTED LIQUID LEVEL TRANSMITTER
• Liquid level measurement with 0.25% accuracy• Pressures from
0–25 to 0–2,770 inH2O (0–6.2 to 0–690 kPa)
• Flush, 2-, 4-, and 6-inch extended diaphragms• Many optional fill fluids to meet application
requirements• Up to 600% elevation or 500% suppression• Adjustable damping• Stainless steel, Hastelloy C-C276, and
Tantalum wetted materials
Pressu
1151
-003
BC
1151
-034
AC
1151
-035
AC
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
OPTIONS
The following sections describe a variety of
available options for the Model 1151 Transmitter. These options will permit greater application flexibility.
Mounting Brac ketsB1 Bracket for 2-in. Pipe Mounting
• Bracket for mounting transmitter on 2-in. pipe.• Constructed of carbon steel with carbon steel
U-bolt.
• Coated with polyurethane paint.B4 Bracket for 2-in. Pipe w ith 316 SST Bolts
• Same bracket as Option Code B1 with 316 SST bolts.B7 304 SST Bracket and 316 SST Bolts
for 2-in. Pipe Mounting• Same bracket as Option Code B1 with all SST
materials.B2 Bracket for Panel Mounting
• Bracket for mounting transmitter on panel or wall.• Constructed of carbon steel with carbon steel bolts.• Coated with polyurethane paint.
B5 Bracket for Panel with 316 SST Bolts• Same bracket as Option Code B2 with 316
SST bolts.
re-42
B3 Flat Bracket for 2- in. Pipe Mounting• Bracket for vertical mounting of transmitter
on 2-in. pipe. • Constructed of carbon steel with carbon steel
U-bolt.• Coated with polyurethane paint.
B6 Flat Bracket for 2- in. Pipe with 316 SST Bolts• Same bracket as Option Code B3 with 316 SST
bolts.B9 304 SST Flat Bracket and 316 SST Bolts
for 2-in. Pipe Mounting• Same bracket as Option Code B3 with all SST
materials.
Bolts and Nuts for Flanges and AdaptersOptions permit bolts and nuts for flanges and adapters in the specified material.L3 ANSI/ASTM A - 193-B7L4 Austenitic 316 SSTL5 ANSI/ASTM A193-B7M
1151
-115
1B04
B
Drain/VentPlug
FlangeBolts
FlangeAdapterBolts
FlangeAdapter
ProcessFlange
FIGURE 2. Model 1151 Flange Configuration.
Rosemount Inc.
re-43
Mod
el 1
151
3051
-305
1B19
A11
51-1
151D
, A06
A30
51-3
051A
19A
1151
-024
4A11
51-1
151E
06A
3051
-305
1H19
B11
51-1
151F
06B
Pressu
5.625(143)
3.75 (95)
1.65 (42)
3.87 (98)
2.81 (71)
NOTEDimensions are in inches (millimeters).
FIGURE 3. Mounting Bracket Option Codes B1, B4, and B7.
4.97 (127)
2.62 (67)
2.625(67)
5.625(143)
2.625(67)
2.625(67)
1.65 (42)
3.87 (98)
NOTEDimensions are in inches (mi llime ters).
1.40(36)
Mounting Holes 0.375 (10) Diameter
3.75 (95)
FIGURE 4. Panel Mounting Bracket Option Codes B2 and B5.
Meters have 2-in. (50.8 mm) scale.Plug-in mounting configuration.Indication accuracy ±2%.
Operating temperature limit: –40 to 150 °F(–40 to 65 °C).Meters are enclosed in a housing certified by Factory Mutual as explosion proof for Class I, Division 1, Groups B, C, and D; Class II, Division 1, Groups E, F, and G and Class III, Division 1.For optional CSA explosion-proof approval, see certification Option Code E6.
M1 Linear Analog Meter, 0–100% ScaleM2 Square Root Analog Meter,
0–100% Flow ScaleM3 Special Scal ing Analog Meter
(Specify Range) M6 Square Root Analog Meter, 0–10 √ Scale
NOTESMeter Options are not available with Output Codes L or M, or Option Codes V2 or V3.
Meter Options M2, M6, M8, and M9 are not available with Output Code J.
Meter Options M4, M7, and M9 are not available with Output Code G.
Pressure-44
LCD4-digit display.Indication accuracy ±0.25% of calibrated span±1 digit.Display resolution at ±0.5% of calibrated span±1 digit.Operating temperature limit: –4 to 158 °F(–20 to 70 °C).Plug-in mounting configuration.
Meters are enclosed in a housing certified by Factory Mutual as explosion proof for Class I, Division 1, Groups B, C, and D; Class II, Division 1, Groups E, F, and G and Class III, Division 1.For Optional CSA explosion-proof approval, see certification Option Code E6.
M4 Linear LCD Meter, 0 to 100%M7 Special Scale LCD M eter (Specify Range,
Mode, and Engineering Units)M8 Square Root LCD Meter, 0 to 100%M9 Square Root LCD Meter, 0–10 √ Scale
751-
0153
A,
1151
-253
4A01
A,
1151
I05A
7.5 Max. (191) Optional Meter
0.75 (19)Clearance forCover Removal(Typical)
9.0 Max. (229)
OPTION CODE M4LINEAR SCALE
OPTION CODE M1LINEAR SCALE
NOTEDImensions are in inches (millimeters).
FIGURE 6. Meter Options.
%
Rosemount Inc.
Mod
el 1
151
Process ConnectionsD1 Side Drain/Vent-Top
Drain/vent valve mounted in side of flange.Top position used to vent gas buildup in liquid process applications with transmitter mounted vertically.Plug of same material as requested flange inserted in end of flange opposite adapter.
D2 Side Drain/Vent-BottomDrain/vent valve mounted in side of flange.
Bottom position used to drain liquid buildup in gas process applications with transmitter mounted vertically.Plug of same material as requested flange inserted in end of flange opposite adapter.
D3 1/4–18 NPT Process ConnectionOption provides 1/4–18 NPT process connection on flanges rather than standard 1/2–14 NPT.Flange adapters are deleted to provide desired connection.
D6 316 SST Low Side Flange(Models 1151GP and 1 151AP Only)
½–14 NPTConnection
on Adapters(¼–18 NPT
Connectionwith Adapters
Removed)
Standard Drain/VentReplaced w ith Plug
Alternate SideDrain/Vent Top Position
(Option Code D1)
Alternate Side Drain/Vent BottomPosition (Opt ion Code D1)
FIGURE 7. Model 1151 Process Connections.
1151
-115
1B04
A
K1 1/4–18 NPT Kynar ™ Process Flange InsertK2 1/2–14 NPT Kynar Process Flange In sert
Options provide Kynar plastic process flange insert that prevents process from coming in contact with the metal of the flange. One process insert for Models 1151AP, GP and LT; two inserts for Model 1151DP.Process connections are from the side.Available with carbon steel and stainless steel process flanges only.
Pressure Maximum: 200 psi at 200 °F with Kynar impulse piping; 300 psi at 200 °F with metal impulse piping.
S1 Assembled with One Remote Diaphragm SealS2 Assembled with Two Remote Diaphragm
SealsOptions provide for the assembly of one or two remote diaphragm seals.For Models 1151AP and 1151LT applications consult factory.
For seal choices, consult Product Data Sheet 00813-0100-4016.
KynarInsert ¼–18 or ½–14 NPT
Process Connection
1151
-115
1D17
A
FIGURE 8. Flange Insert.
Pressure-45
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
1151
-115
1B17
B
S4 Assembled with Model 1195 Integral OrificeDesigned for highly accurate, small-bore flow measurement of any clean gas, liquid, or vapor. See Product Data Sheet 00813-0100-4686.Reduce the costs associated with traditional orifice plate installations.Several configurations are available factory assembled to Rosemount differential pressure transmitters.(1)
Wide orifice bore/flow range capability.Wide choice of process connections, including threaded, socket weld, and ANSI flanges.Static pressure maximum limit is 3,000 psig.Wetted materials are available that comply with NACE MR 01-75(90).Available only with Ranges 2, 3, 4, and 5.
For integral orifice selection, see Product Data Sheet 00813-0100-4686.
(1) Applicable only to orifice assemblies without piping.
OPTIONAL3-VALVE MANIFOLD
MODEL 1195 INTEGRAL ORIFICE ASSEMBLY
FIGURE 9. Model 1151 with Manifold and Model 1195 Integral Orifice.
re-46
1151
-115
1A21
A
Wetted O-rings
W2 Buna NW3 Ethylene-PropyleneW4 Aflas ®
W6 Spring-Loaded Teflon ®
Contains a Hastelloy spring that is in contact with the process fluid. Consult factory if Hastelloy is unacceptable.
ProceduresStandard Configuration
Unless otherwise specified, transmitter will be shipped as follows:Engineering Units: inH2O4 mA: 020 mA: Upper Range LimitOutput: LinearSoftware Tag: BlankCustomer may specify the above items at no charge. Software tag (8 characters) is left blank unless specified.
WettedO-rings
FIGURE 10. Flange Exploded View.
Rosemount Inc.
Mod
el 1
151
C9 Custom Configuration (Option C ode C9)If Option Code C9 is ordered, the customer may specify the following data in addition to the standard configuration parameters. Refer to Configuration Data Sheet 00806-0100-4593.Descriptor: 16 charactersMessage: 32 charactersDate: Day, Month, YearDamping: SecondsBurst Mode: Select Output ChoiceFlange Material: Model Code InformationO-Ring Material: Model Code InformationIsolator Material: Model Code InformationSensor Fluid: Model Code InformationDrain/Vent: Model Code InformationIntegral Meter: Installed or NoneRemote Seal: Specified InformationFailure Mode: High or LowTransmitter Security: Off or On
P1 Hydrostatic TestingEach transmitter is hydrostatic tested according to Table 1.Test medium is water.This option provided for transmitters with remote diaphragm seal on application only.
Rosemount Procedure 1746 outlines the testing procedure.
P2 Cleaning for Special ServiceThis option minimizes contaminants to the process system by cleaning wetted surfaces with a suitable detergent.Rosemount Procedure 97412 outlines the cleaning procedure.
P3 Cleaning for <1 PPM Chlorine/Fluorine
TABLE 1. Hydrostatic Test Pressure.
Model Test Pressure
1151DP 3,000 psi
1151HP 6,750 psi
1151AP 2,000 psi
1151GP
Ranges 3–8 2,000 psi
Range 9 4,500 psi
Range 0 7,500 psi
1151LT
Class 150 Flange 450 psi
Class 300 Flange 1,100 psi
1151DR 1,500 psi
P4 Calibration at Line PressureThis option allows transmitters to be calibrated at an elevated line pressure rather than atmospheric pressure.Customer must specify line pressure at which transmitter is to be calibrated.Customer is provided with calibration data at line pressure and equivalent data at atmospheric pressure.Available with Models 1151DP and 1151HP only. (Not available with Remote Seals.)Elevated line pressure and differential span desired for calibration must not exceed the rated pressure for that model of transmitter.
Minimum differential span that can be calibrated at elevated line pressure is 30 inH2O; maximum is 300 psi.Rosemount Procedure 3787 outlines the calibration procedure.
P5 Calibration at TemperatureThis option allows transmitters to be calibrated at temperatures other than room temperature in the range of 0 to 200 °F (–18 to 93 °C).Customer must specify temperature at which transmitter is to be calibrated and calibration range.Calibration temperature will be printed on instrument tag specified by customer, or on a tag wired to the transmitter if no tag is specified.
Rosemount Procedure 27823B outlines the calibration procedure.
Pressure-47
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
P7 Enhanced T emperature Performancefor A nalog ElectronicsTransmitter is specifically compensated as a complete assembly and will exhibit 1/2 of the standard temperature coefficient over the ambient temperature range of 20 to 140 °F (–7 to 60 °C). Outside this range, the unit will meet the standard temperature effect specification published for that model.Not available on Range 10, limited to 1,500 psi on Range 9.The transmitter is compensated as an assembly; therefore, units in which the sensor module or electronics are changed after the P7 procedure has been performed will meet the standard published temperature specification for that particular model.
Available on DP, GP, and HP models, Ranges3–8, with SST diaphragms and Output Codes E, G, L, and M.
P8 0.1% Accuracy for Analog Elect ronicsAvailable on Model 1151DP (Ranges 3–8), GP (Ranges 3–8), HP, and LT transmitters with 316 SST diaphragms and Output Codes E, G, L, and M.
re-48
OutputsV1 Reverse Output
This option permits reversing of pressure input so that electrical output will increase as pressure input decreases.This option applies only to Models 1151GP and 1151LT. When this option is selected, the process flange, adapter, drain/vent valve, appropriate O-rings, and bolting are installed on low side of transmitter. Not available for Ranges 9 and 0.
Not available with Model 1151AP. Reverse output on Models 1151DP, 1151HP, and 1151DR can be obtained by connecting high-pressure input to low side of transmitter and vice versa.This option should not be ordered with smart transmitters (Output Code S). The Model 1151 Smart transmitter can be configured for reverse output through a HART-Compatible Interface.
V2 1 V Test ResistorA 1 V precision resistor is mounted across the test terminals to provide 4–20 mV output or a 10–50 mV output if 10–50 mA output is used.This option cannot be used with any meter options or Option Codes I5 or I6.
V3 5 V Test ResistorA 5 V precision resistor is mounted across test terminals to provide 20–100 mV output or a50–250 mV output if 10–50 mA output is used.This option cannot be used with any meter options or Option Codes I5 or I6.
Z1 4-Wire, 0–20 mA OutputZ2 4-Wire, 0–16 mA OutputZ3 4-Wire, 0–10 mA Output
These options provide a zero-based current output.
These options cannot be used with any meter or certification options, Vx options, or Output Codes G, L, M, or S.
Rosemount Inc.
Pressure-49
Mod
el 1
151
SPECIFICATIONS
Functional SpecificationsServiceLiquid, gas, and vapor applications.RangesSee Table 3 for ranges. Minimum span equals the upper range limit (URL) divided by rangedown. Rangedown varies with the output code See Table 2. Outputs
Code S, Smart4–20 mA dc, user selectable for linear or square root output. Digital process variable superimposed on 4–20 mA signal, available to any host that conforms to the HART protocol.Code E, Analog4–20 mA dc, linear with process pressure.Code G, Analog10–50 mA dc, linear with process pressure.Code J, Analog4–20 mA dc, square root of differential input pressure between 4 and 100% of input. Linear with differential input pressure between 0 and 4% of input.Code L, Low Power0.8 to 3.2 V dc, linear with process pressure.
Code M, Low Power1 to 5 V dc, linear with process pressure.
Power SupplyExternal power supply required. Transmitter operates according to the following requirements:
Output C odes S, E, J 12 to 45 V dc with no load.Output Code G 30 to 85 V dc with no load.Output C ode L 5 to 12 V dc.Output Code M 8 to 14 V dc.
Where:
(1) A minimum of 250 ohms is required for communication.
(2) For CSA approvals Vmax = 42.4 V dc.
Code Vmin Vmax Rmin Rmax RL at Supply Voltage (V S)
S(1) 12 45 0 1650 RL = 43.5 (VS – 12)
E(2), J
12 45 0 1650 RL = 50 (VS – 12)
G 30 85 0 1100 RL= 20 (VS – 30)
L 5 12 Low Power Minimum Load Impedance:100 kVM 8 14
Rmax
RL
Rmin
Vmin VS Vmax0
Operating Region
Current Consumption Under Normal Operating Conditions (Low Power Only)
Output Code L1.5 mA dc.Output Code M2.0 mA dc.
Span and ZeroOutput Code SSpan and zero may be accessed with local adjustments or remotely through a HART-compatible Interface.Output Codes E, G, J, L, and MSpan and zero are continuously adjustable.
Zero Elevation and SuppressionOutput Codes S, E, and GZero elevation and suppression must be such that the lower range value is greater than or equal to the (–URL) and the upper range value is less than or equal to the (+URL). The calibrated span must be greater than or equal to the minimum span.Output Code JZero is adjustable up to 10% of the calibrated flow span.Output Code LZero is adjustable ±10% of URL and span is adjustable from 90 to 100% of URL.Output Code MZero is adjustable ±50% of URL and span is adjustable from 50 to 100% of URL.
Model 1151 Alp haline ® Press ure Transmitters
Pressu
Model 1151
(1) Transmitter is capable of measuring from –URL to URL.
(1) Available with Ranges 3–5.
TABLE 2. Rangeability.
Output CodeMini mum Span
(URL=Upper Range Limit)Maximum Span
S (DP and GP, SST, Range 3–8; HP SST, Range 4–7) URL/15 2 3 URL(1)
S (All Others) URL/6 2 3 URL(1)
E, G, J URL/6 URL
L URL/1.1 URL
M URL/2 URL
TABLE 3. Model 1151 Transmitter Range Availability by Model (URL = Upper Range Limit).
Range Code Model 1151 Ranges (URL) DP HP GP DP/GP/Seals AP LT
Code Model 1151 Output Opt ions/Damping DP HP GP DP/GP/Seals AP LT
S 4–20 mA, Digital, Smart/Variable • • • • • •
E 4–20 mA, Linear, Analog/Variable • • • • • •
G 10–50 mA, Linear, Analog/Variable • • • • • •
J(1) 4–20 mA, Square Root, Analog/Variable • • NA NA NA NA
L 0.8 to 3.2 V, Linear, Low Power/Fixed • • • • • NA
M 1 to 5 V, Linear, Low Power/Fixed • • • • • NA
re-50
Rosemount Inc.
Mod
el 1
151
Temperature LimitsElectronics Operating
Code S –40 to 185 °F (–40 to 85 °C).Code E –40 to 200 °F (–40 to 93 °C)Code G, L, M –20 to 200 °F (–29 to 93 °C).Code J –20 to 150 °F (–29 to 66 °C).
Sensing Element OperatingSilicone fill –40 to 220 °F (–40 to 104 °C).Inert fill 0 to 160 °F (–18 to 71 °C).
StorageCode S –60 to 185 °F (–51 to 85 °C).Codes E, G, L, M –60 to 250 °F (–51 to 121 °C).Code J –60 to 180 °F (–51 to 82 °C).
Model 1151LT T emperature Limits
(1) Temperature limits are reduced in vacuum service. Contact your local Rosemount representative for assistance.
(2) Glycerin and Water and Propylene Glycol and Water are not suitable for vacuum service.
(3) Not compatible with Buna-N or Ethylene-Propylene O-ring material.
Fill FluidTempe rature
Limits (1)SpecificGravity
Coeff. of Therm. Exp.
cc/cc/°F(cc/c c/°C)
Viscosityat 25 °C
centistokes
D.C.® 200 Silicone
–40 to 400 °F(–40 to 205 °C)
0.9340.00060
(0.00108)9.5
D.C. 704Silicone
60 to 400 °F(15 to 205 °C)
1.070.00053
(0.00095)44
Inert Fill–50 to 350 °F
(–45 to 177 °C)1.85
0.0004(0.000864)
6.5
Syltherm®
800, Silicone–50 to 400 °F
(–45 to 205 °C)0.934
0.00052(0.000936)
9.5
SylthermXLT, Silicone
–100 to 300 °F(–73 to 149 °C)
0.850.000666
(0.001199)1.6
Glycerin and Water(2)
0 to 200 °F(–17 to 93 °C) 1.13
0.00019(0.00034) 12.5
PropyleneGlycoland Water(3)
0 to 200 °F(–17 to 93 °C)
1.02
0.00019(0.00034)
2.85
Neobee M-20(3)
0 to 400 °F(–17 to 205 °C)
0.9000.00056
(0.001008)9.8
Static Pressure and Overpressure LimitsModel 1151DP0 psia to 2,000 psig (0 to 13.79 MPa) on either side without damage to transmitter. Operates within specifications from static line pressures of 0.5 psia (3.45 kPa) to 2,000 psig (13.79 MPa).Model 1151HP0 psia to 4,500 psig (0 to 31.02 MPa) on either side without damage to transmitter. Operates within specifications from 0.5 psia (3.45 kPa) to 4,500 psig (31.02 MPa).Model 1151AP0 psia to 2,000 psia (0 to 13.79 MPa) without damage to transmitter. Operates within specifications from 0 psia to the upper range limit of the transmitter.
Model 1151GP0 psia to 2,000 psig (0 to 13.79 MPa) for ranges to 1,000 psig (6.90 MPa), 4,500 psig (31.02 MPa) for the 3,000 psig (20.68 MPa) range, and 7,500 psig (51.71 MPa) for the 6,000 psig (41.37 MPa) range, without damage to the transmitter. Operates within specifications from 0.5 psia (3.45 kPa) to the upper range limit of the transmitter.Model 1151LT
Burst Pressure All Models10,000 psig (68.95 MPa) proof pressure on the flanges.Humidity Limits0 to 100% relative humidity.
Volumetric Di splacementLess than 0.01 in3 (0.16 cm3).
(1) At 100 °F (38 °C); the rating decreases with increasing temperature.
(2) At 248 °F (120 °C); the rating decreases with increasing temperature.
Standard Class/Rating Carbon SteelStainless
Steel
ANSI 150 285 psig(1) 275 psig(1)
ANSI 300 740 psig(1) 720 psig(1)
ANSI 600 1,480 psig(1) 1,440 psig(1)
DIN PN 10–40 40 bar(2) 40 bar(2)
DIN PN 10/16 16 bar(2) 16 bar(2)
DIN PN 25/40 40 bar(2) 40 bar(2)
Pressure-51
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
Failure Mode Alarm (Output Code S)If self-diagnosis detects a gross transmitter failure, the analog signal will be driven below 3.9 mA or above 21 mA to alert the user. High or low alarm signal is user selectable.
Transmitter Security (Output C ode S)Activating the transmitter security function prevents changes to the transmitter configuration, including local zero and span adjustments. Security is activated by an internal switch.Overpressure Alarm (Output C ode S)If the sensor detects a negative overpressure value, the analog signal will be driven to 3.9 mA. If the sensor detects a positive overpressure value, the analog signal is driven to 20.8 mA.DampingNumbers given are for silicone fill fluid at room temperature. The minimum time constant is 0.2 seconds (0.4 seconds for Range 3). Inert-filled sensor values would be slightly higher.
Output Code STime constant is adjustable in 0.1 second increments from minimum to 16.0 seconds.Output Codes E and GTime constant continuously adjustable between minimum and 1.67 seconds.
Output Code JTime constant continuously adjustable between minimum and 1.0 second.Output Codes L, MDamping is fixed at minimum time constant.Model 1151LTTime constant continuously adjustable between 0.4 and 2.2 seconds with silicone oil fill, or 1.1 and 2.7 seconds with inert fill for flush models and electronics codes E or G.
Turn-on TimeMaximum of 2.0 seconds with minimum damping. Low power output is within 0.2% of steady state value within 200 ms after application of power.
Ranges 3 through 8, DP and GP transmitters;Ranges 4 through 7, HP transmitters
±0.1 of calibrated span for spans from 1:1 to 10:1 of URL. Between 10:1 and 15:1 of URL.
All other ranges and t ransmitters±0.25% of calibrated span.
Output Code S, square root mode
Output Codes E, G, L, and M±0.2% of calibrated span for Model 1151DP Ranges 3 through 5. All other ranges and transmitters, ±0.25% of calibrated span.Output Code J±0.25% of calibrated span.
StabilityOutput Code S±0.1% of URL for six months for DP and GP Ranges 3 through 8. (±0.25% for all other ranges and transmitters.)Output Codes E and G±0.2% of URL for six months for Ranges 3 through 5. (±0.25 for all other ranges.)Output Codes J, L, and M±0.25% of URL for six months.
Temperature EffectOutput Code S [–20 to 185 °F (–29 to 85 °C)]
For DP and GP transmitter Range 4 through 8; HP transmitter R ange 4 through 7:
Zero Error = ±0.2% URL per 100 °F (56 °C)Total Error = ±(0.2% URL + 0.18% of calibrated span) per 100 °F; For Range 3, double the stated effects. For other ranges and transmitters follow analog temperature specifications (Output Code E).
Output Code E, G, L, and M[–20 to 200 °F (–29 to 93 °C)]
For Ranges 4 through 0Zero Error = ±0.5% URL per 100 °F.Total Error = ±(0.5% URL + 0.5% of calibrated span) per 100 °F; double the effect for Range 3.
Output Code JThe total output effect, whether at zero or full scale, including zero and span errors is ±1.5% of URL per 100 °F (56 °C). ±2.5% of URL per 100 °F (56 °C) for Range 3.
accuracy 0.02URLspan--------------
0.1– % of calibrated span±=
0.2 0.05URLspan-------------
×+ % of calibrated flow span±
Rosemount Inc.
Pressure-53
Mod
el 1
151
Static Pressure EffectDP Transmitters
Zero Error±0.25% of URL for 2,000 psi (13790 kPa) for Range 4 and 5 or ±0.5% for other ranges, correctable through rezeroing at line pressure.
Span ErrorCorrectable to ±0.25% of input reading per 1,000 psi (6895 kPa), or to ±0.5% for Range 3. For Output Code J, the span error is correctable to ±0.125% of output reading per 1,000 psi, or to ±0.25% for Range 3.
HP TransmittersZero Error±2.0% of URL for 4,500 psi (31027 kPa), correctable through rezeroing at line pressure.Span ErrorCorrectable to ±0.25% of input reading per 1,000 psi (6895 kPa). For Output Code J, the span error is correctable to ±0.125% of output reading per 1,000 psi.
Vibration Effect0.05% of URL per g to 200 Hz in any axis.
Power Supply EffectOutput C odes S, E, G, and JLess than 0.005% of output span per volt.Output C odes L, MOutput shift of less than 0.05% of URL for a 1 V power supply shift.
Load EffectOutput C odes S, E, G, and JNo load effect other than the change in power supplied to the transmitter.Output C odes L, MLess than 0.05% of URL effect for a change in load from 100 kV to infinite ohms.
Short Circuit Condition (Low Power Only)No damage to the transmitter will result when the output is shorted to common or to power supply positive (limit 12 V).EMI/RFI EffectOutput shift of less than 0.1% of span when tested to SAMA PMC 33.1 from 20 to 1000 MHz and for field strengths up to 30 V/m. (Code J is 0.1% of flow span.)Mounting Position EffectZero shift of up to 1 inH2O (0.25 kPa). Range 3 transmitters with Output Code J should be installed with the diaphragm in the vertical plane.With liquid level diaphragm in vertical plane, zero shift of up to 1 inH2O (0.25 kPa). With liquid level diaphragm in horizontal plane, zero shift of up to 5 inH2O (1.25 kPa) plus extension length on extended units. All zero shifts can be calibrated out. No effect on span.
Physical Specifications,Standard Con figurationWetted Materials
Isolating Diaphragms316L SST, Hastelloy C-276, Monel, gold-plated Monel, or Tantalum. See ordering table for availability per model type.
Drain/Vent Valves316 SST, Hastelloy C, or Monel. See ordering table for availability per model type.Process Flanges and AdaptersPlated carbon steel, 316 SST, Hastelloy C, or Monel. See ordering table for availability per model type.Wetted O-ringsViton® (other materials also available). With gold-plated Monel diaphragms (diaphragm Code _6), special fluorocarbon O-rings are supplied.
Non-wetted MaterialsFill FluidSilicone oil or inert fill.Bolts and Bolting Flange (GP and AP only)Plated carbon steel.Electronics HousingLow-copper aluminum. NEMA 4X.Cover O-ringsBuna-N.PaintPolyurethane.
Process Connect ions1/4–18 NPT on 2.125-in. (54-mm) centers on flanges for Ranges 3, 4, and 5.1/4–18 NPT on 2.188-in. (56-mm) centers on flanges for Ranges 6 and 7.1/4–18 NPT on 2.250-in. (57-mm) centers on flanges for Range 8.1/2–14 NPT on adapters.For Ranges 3, 4, and 5, flange adapters can be rotated to give centers of 2.0 in. (51 mm), 2.125 in. (54 mm), or 2.250 in. (57 mm).Electrical Connect ions1/2–14 NPT conduit with screw terminals and integral test jacks compatible with miniature banana plugs (Pomona 2944, 3690, or equivalent). The HART Hand-Held Interface connections are fixed to the terminal block on smart transmitters.
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
Weight12 lb (5.4 kg) for AP, DP, GP, and HP transmitters, excluding options.
Meter Option: Add 2 lb (1 kg).Hazardous Locations Certi ficationsStainless steel certification tag is provided.
Factory Mutual (FM) ApprovalsFM Explosion Proof tag is standard. Appropriate tag will be substituted if optional certification is selected.
Default Explosion Proof: Class I, Division 1, Groups B, C, and D. Dust-Ignition Proof: Class II, Division 1, Groups E, F, and G. Suitable for use in: Class III, Division 1. Indoor and outdoor use. NEMA 4X. Factory Sealed.
I5 Intrinsic Safety and Non-incendive Approvals: FM certifications optional for specific Classes, Divisions, and Groups when connected in accordance with the FM entity approvals,see Table 7. Factory Sealed.
K5 Combination of Explosion Proof, Intrinsic Safety, and Non-incendive Approvals.
Canadian Standards Association (CSA) ApprovalsE6 Explosion proof for Class I, Division 1, Groups
C and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 Hazardous Locations. Certified for Class I, Division 2, Groups A, B, C, and D; CSA enclosure type 4X. Factory Sealed.
I6 Intrinsic Safety Approvals CSA certifications optional for specific Classes, Divisions, and Groups when connected in accordance with the CSA barrier selection table, Table 8. Temperature Code T2D.
C6 Combination of I6 and E6, CSA Explosion Proof and Intrinsic Safety Approval. Factory Sealed.
K6 CSA/CENELEC Explosion-Proof and Intrinsic Safety Approval.
(1) Stainless steel flange weights are listed.
TABLE 6. Flange Weights with Model 1151LT Transmitter.
Flange (1) Flush2-in
(50mm)Ext.
4-in. (100mm)
Ext.
6-in. (150mm)
Ext.
2-in., Class 1503-in., Class 1504-in., Class 1502-in., Class 3003-in., Class 3004-in., Class 3002-in., Class 6003-in., Class 600
Standards Association of Aust ralia (SAA) Flameproof CertificationE7 Flameproof
Ex d IIB + H2 T6.Class I, Zone 1.Dust-Ignition proofDIP T6.Class II.Special Conditions: For transmitters having NPT or PG cable entry threads, an appropriate flameproof thread adaptor shall be used to facilitate application of certified flameproof cable glands.
I7 Intrinsically SafeEx ia IIC T6 (Tamb = 40 °C).Ex ia IIC T5 (Tamb = 70 °C).Class I, Zone 0.
Special Conditions: Observe electrical connection parameters when installing transmitter.
Standards Association of Aust ralia (SAA)
N7 Type NEx n IIC T6 (Tamb = 40 °C).Ex n IIC T5 (Tamb = 70 °C).Class I, Zone 2.Special Conditions: The equipment must be connected to a supply voltage which does not exceed the rated voltage. The enclosure end caps must be correctly fitted whilst the equipment is energized.
CESI/CENELEC Flameproof CertificationE8 90.C.016: EEx d IIC T6 (without meter).
Special Conditions: When transient protection terminal options (R1 or R9) are installed, the transmitter must be supplied from a galvanically isolated i.s. barrier.
EEx ia IIC T5 (Tamb = 40 °C).EEx ia IIC T4 (Tamb = 80 °C).AnalogEEx ia IIC T5.Special Conditions: When transient protection terminal options (R1 or R9) are installed, the transmitter must be supplied from a galvanically isolated i.s. barrier.
Rosemount Inc.
el 1
151
BASEEFA Type N (Non-incendive) CertificationN1 Smart
Ex N II T5 (Tamb = -40 °C to 50 °C); Un = 45 V.Ex N II T4 (Tamb = -40 °C to 80 °C); Un = 45 V.AnalogEx N II T6; Un = 28 V.Special Conditions: The apparatus must be installed in accordance with BS 5345: Part 7: 1979 and be earthed by means of enclosure earth terminal.
Schweizerischer Elektrotechnischer Verein (SEV) Intrinsic Safety CertificationIC Smart
EEx ia IIC T5 (Tamb = 40 °C).EEx ia IIC T4 (Tamb = 80 °C).AnalogEEx ia IIC T6 (Pmax = 0.35 W).EEx ia IIC T5 (Pmax = 0.65 W).EEx ia IIC T4 (Pmax = 0.95 W).
Mod
TABLE 7. FM Entity Approvals.
1151 ParametersEquipment Associated
Parameters
FM Approved for Class I, II, III, Division 1 and 2 Groups
FIGURE 12. Typical Transmitter Exploded View, Shown with Smart Electronics.
Rosemount Inc.
re-57
Mod
el 1
151
1151
-51L
TB
05A
1151
-115
1B30
B11
51-5
1LTA
05A
3051
-305
1B27
B
Pressu
(1) Tolerances are 0.040 (1.02), –0.020 (0.51).
TABLE 9. Model 1151LT Dimensional Specifications.
ClassPipe Size
Flange Thickness
A
Bolt Circle Diameter
B
Outside Diameter
C
No. of
Bolts
Bolt Hole Diameter
Exten.Diam.
D (1)
O.D.Gask.Surf.
E
Lower Housing
XmtrSide
F
Proc. Side
G
ANSI 150
2 (51)3 (76)4 (102)
1.12 (28)1.31 (33)1.31 (33)
4.75 (121)6.0 (152)7.5 (190)
6.0 (152)7.5 (190)9.0 (228)
448
0.75 (19)0.75 (19)0.75 (19)
NA2.58 (65)3.5 (89)
3.75 (95)5.0 (127)6.81 (173)
2.9 (74) 3.11 (79)4.06 (103)
2.16 (55)3.11 (79)4.06 (103)
ANSI 300
2 (51)3 (76)4 (102)
1.25 (32)1.50 (38)1.62 (41)
5.0 (127)6.62 (168)7.88 (200)
6.5 (165)8.25 (209)10.0 (254)
888
0.75 (19)0.88 (22)0.88 (22)
NA2.58 (65)3.5 (89)
3.75 (95)5.0 (127)6.81 (173)
2.9 (74) 3.11 (79)4.06 (103)
2.16 (55)3.11 (79)4.06 (103)
ANSI 600
2 (51)3 (76)
1.12 (28)1.37 (35)
5.0 (127)6.62 (168)
6.5 (165)6.62 (168)
88
0.75 (19)0.88 (22)
NA2.58 (65)
3.75 (95)5.0 (127)
2.9 (74) 3.11 (79)
2.16 (55)3.11 (79)
DINPN10-40
DN 50 26 mm 125 mm 165 mm 4 18 mm NA 95 mm 74 mm 55 mm
DINPN 25/40
DN 80DN 100
30 mm30 mm
160 mm190 mm
200 mm235 mm
88
18 mm22 mm
65 mm89 mm
127 mm173 mm
79 mm103 mm
79 mm103 mm
DINPN 10/16
DN 100 26 mm 180 mm 220 mm 8 18 mm 89 mm 173 mm 103 mm 103 mm
C
B
DIAPHRAGM ASSEMBLY AND MOUNTING FL ANGE
NOTEDimensions are in inches (millimeters).
MeterHousing
Terminal C onnect ionsThis Side
Namepl ate (Remove for Span and Zero Adjust)
Transmit ter Circui try This Side
½–14 NPT forConduit Conn ection(2 places)
0.75 (19) Clearance for Cover Removal (typical)
½–14 NPTon FlangeAdapters
¼–18 NPT on Flangesfor Pressure Connectionwithout the Use of FlangeAdapters
Permanent Tag(optional)
11.38 (289) Max. Serrated Face
Gasket Surface
ED
AWired-on Tag(standard)
FlangeAdapter
2-, 4-, or 6-in.(51, 102, or 152)Extension
4.5 (114)Max.
4.5 (114)Max.
4.45 (113) Max.
7.5 (190.5)Max. with Optional
Meter
FIGURE 13. Dimensional Drawings.
FlushingConnection
1(25)
FGE
OPTIONAL FLUSHING CONNECTION RING(LOWER HOUSING)
Drain/Vent Valve
Model 1151 Alp haline ® Press ure Transmitters
Pressu
Model 1151
ORDERING INFORMATION
(1) Bolts and conduit plugs are plated carbon steel.
(2) On GP and AP transmitters, the low-side flange is plated carbon steel. For a stainless-steel low-side flange, order process connection Option Code D6.
(3) These selections meet NACE material recommendations per MR 01-75.
TABLE 10. Model 1151 Differential, High Line, Gage and Absolute Pressure Transmitters. — = Not Applicable • = Applicable
Model Transmitter Type (select one) DP HP GP AP
1151DP1151HP1151GP1151AP
Differential Pressure TransmitterDifferential Pressure Transmitter for High Line PressuresGage Pressure TransmitterAbsolute Pressure Transmitter
•———
—•——
——•—
———•
Code Pressure R anges (URL) (select one)—For R angeability, see below DP HP GP AP
(1) Bolts and conduit plugs are plated carbon steel.
(2) On GP and AP transmitters, the low-side flange is plated carbon steel. For a stainless-steel low-side flange, order process connections Option Code D6.
(3) These selections meet NACE material recommendations per MR 01-75.
(1) Not available with Output Codes L or M, or Option Codes Zx, V2, or V3.
(2) Not available with Output Codes J, L, M, or Option Codes Zx, V2, or V3.
(3) Not available with Output Codes G, L, M, or Option Codes Zx, V2, or V3.
(4) Not available with Output Codes G, J, L, M, or Option Codes Zx, V2, or V3.
TABLE 10. (continued).
CodeMATERIALS OF CONSTRUCTION (1) Flanges/Adapters Drain/Vents Diaphragms Fill Fluid DP HP GP(2) AP(2)
Analog Scale, Linear Meter, 0–100%Analog Scale, Square Root Meter, 0–100% FlowAnalog Scale, Linear Meter, Special ScaleLCD Meter, Linear Meter, 0–100%, User SelectableAnalog Scale, Square Root Meter, 1–10√LCD Meter, Linear Meter, Special ConfigurationLCD Meter Square Root Meter, 0–100% FlowLCD Meter, Square Root Meter, 0–10√
••••••••
••••••••
•—••—•——
•—••—•——
Pressure-59
Model 1151 Alp haline ® Press ure Transmitters
Pressu
Model 1151
(1) Not available with Output Code G or Option Code Zx.
(2) Not available with Option Codes M1–M9.
(3) Not available with Output Codes G, J, L, M, or Option Code Zx.(4) Not available with Output Code G or Option Code Zx.
(5) Not available with Output Codes G, J, L, M, S, or Option Code Zx.
(6) Not available with Output Codes G, L, M, or Option Code Zx.
(7) This option is available for the transmitter flange and adapters.(8) Option includes SST housing, covers, conduit plug, locknut, L4 bolting, and D6 low side blank flange for GP and AP transmitters.
Option Codes L4 and D6 parts are included with housing Option Codes H1 and H2.
TABLE 10. (continued).
Code Certifications (optional - select one) DP HP GP AP
E6I5(1)
K5I6(1)
C5(2)
C6(1)
K6E4E7E8I1(3)
I7(4)
I8(5)
N1(6)
N7IC(3)
Q4Q8(7)
Canadian Standards Association (CSA) Explosion-Proof ApprovalFactory Mutual (FM) Non-incendive and Intrinsic Safety ApprovalFactory Mutual (FM) Explosion-Proof and Intrinsic Safety CombinationCanadian Standards Association (CSA) Intrinsic Safety Approval Industry and Science Canada (ISC) Approval (Available in Canada Only)Combination of I6 and E6; CSA Explosion-Proof and Intrinsic Safety Approval
(Requires 42.4 V dc max. power supply)CSA/CENELEC Explosion-Proof and Intrinsic Safety ApprovalJapanese Industrial Standards (JIS) Flameproof CertificationStandards Association of Australia (SAA) Flameproof CertificationCESI/CENELEC Flameproof CertificationBASEEFA Intrinsic Safety CertificationStandards Association of Australia (SAA) Intrinsic Safety CertificationCESI/CENELEC Flameproof CertificationBASEEFA Type N CertificationStandards Association of Australia (SAA) Non-incendive Safety ApprovalSchweizerischer Elektrochnischer Verein (SEV) Intrinsic Safety CertificationCalibration Data SheetMaterial Traceability per EN 10204 3.1B
•••••
•••••••••••••
•••••
•••••••••••••
•••••
•••••••••••••
•••••
•••••••••••••
Code Housing DP HP GP AP
H1(8)
H2(8)
H3H4C1C2J1
SST Non-wetted Parts on Transmitter without MeterSST Non-wetted Parts on Transmitter with MeterSST Housing, Covers, Conduit Plug, Lock-nut, Without MeterSST Housing, Covers, Conduit Plug, Lock-nut, With MeterPG 13.5 Conduit Threads (Available in Germany Only)M20 Conduit Threads (Available in Germany Only)G½ Conduit Threads
•••••••
•••••••
•••••••
•••••••
Code Termi nal Blocks DP HP GP AP
R1 Integral Transient Protection (Only available with Option Code S and E electronics) • • • •
Code Bolts for Flanges and Adapters (optional - select one) DP HP GP AP
L3L4L5
ASTM A193-B7 Flange and Adapter Bolts316 SST Flange and Adapter BoltsASTM A193-B7M Flange and Adapter Bolts
(2) The maximum working pressure on this option is 300 psig. Available only with materials of construction Option Codes 1x or 2x.
(3) This option may only be used on Ranges 4–8.(4) This option has a maximum static pressure rating of 3,000 psi, and is available for factory
assembly only without associated piping and is available only for Ranges 2, 3, 4, and 5.
TABLE 10. (continued).
Code Process Con nections (optional (1)) DP HP GP AP
D1
D2
D3
D4D5
D6
D9
G1G2G3G4G5G6K1(2)
K2(2)
S1(3)
S2(3)
S4(4)
Side Drain/Vent, Top
Side Drain/Vent, Bottom
Process Adapters Deleted
Conformance to DIN 19213 and DIN 50049 3.1B Ranges 3, 4, 5 (Available in Germany Only)Conformance to DIN 19213 and DIN 50049 3.1B Ranges 6, 7, 8, without ¼ NPT Threads or
Drain/Vent Valve Connections (Available in Germany Only)316 SST Low Side Blank Flange
JIS Process Connection–RC ¼ Flange with RC ½ Flange Adapter
DIN Spacing (Single Entry Port, No Side V/D Hole Flange)DIN Spacing (Single Entry Port, Two Side V/D Hole Flange)DIN Spacing (Dual Entry Port, No Side V/D Hole Flange)DIN Spacing (Dual Entry Port, One Top Side V/D Hole Flange)DIN Spacing (Dual Entry Port, One Bottom Side V/D Hole Flange)DIN Spacing (Dual Entry Port, Two Side V/D Hole Flange)Kynar insert, ¼–18 NPTKynar insert, ½–14 NPTAttachment of One Remote Seal - See PDS 00813-0100-4016 Attachment of Two Remote Seals - See PDS 00813-0100-4016 Attachment of Integral Orifice Assembly - See PDS 00813-0100-4686
(1) Contains a Hastelloy spring that is wetted by the process; consult factory for Teflon O-ring without a spring.
(2) Available with Output Code S only.
(3) Hydrostatic testing for Range 0, 125% maximum working pressure.(4) Fluorolube® grease on wetted O-rings.
(5) Not available on Range 10: limited to 1,500 psi on Range 9; not applicable with Output Code S.
(6) Available only with stainless steel isolators and for span of 10 inH2O and greater;not applicable with Output Code S; available only with Output Codes E, G, L, or M;not available on AP or DR transmitters.
(7) Reverse output option is not needed with smart electronics; configured via HART-based communicator.(8) Not available with Output Codes L or M.
(9) Not available with Option Codes Mx, Vx, Ix, or Ex, or Output Codes G, L, M, or S.
TABLE 10. (continued).
Code Wetted O-ring Material DP HP GP AP
W2W3W4W6(1)
Buna-NEthylene-PropyleneAflasSpring-loaded Teflon
••••
•••—
••••
••••
Code Procedures DP HP GP AP
C9(2)
P1(3)
P2(4)
P3P4P5P7(5)
P8(6)
Software ConfigurationHydrostatic Testing, 150% Maximum Working PressureCleaning for Special ServiceCleaning for <1 PPM Chlorine/FluorineCalibrate at Line PressureCalibrate at Specific TemperatureImproved Temperature CoefficientCalibrate to 0.1% Accuracy
••••••••
••••••••
•••——•••
•••—••——
Code Outputs DP HP GP AP
V1(7)
V2(8)
V3(8)
Z1(9)
Z2(9)
Z3(9)
Reverse Output4–20 mV Test Signal20–100 mV Test Signal4-wire, 0–20 mA Output4-wire, 0–16 mA Output4-wire, 0–10 mA Output
—•••••
—•••••
••••••
—•••••
Typical Model Number: 1 151DP 4 S 52 B3 M1
re-62
Rosemount Inc.
Mod
el 1
151
TABLE 11. Model 1151LT Flange-Mounted Liquid Level Transmitter.
Code Process Fill—High Pressure Side Temperature Limits
ACDHGNPS
Syltherm XLT –100 to 300 °F (–73 to 135 °C)D. C. Silicone 704 60 to 400 °F (15 to 205 °C)D. C. Silicone 200 –40 to 400 °F (–40 to 205 °C)Inert –50 to 350 °F (–45 to 177 °C)Glycerin and Water 0 to 200 °F (–17 to 93 °C)Neobee M-20 0 to 400 °F (–17 to 205 °C)Propylene Glycol and Water 0 to 200 °F (–17 to 93 °C)Syltherm 800 –50 to 400 °F (–45 to 205 °C)
re-64
Rosemount Inc.
Mod
el 1
151
(1) For welded capillary assemblies, order sensor module and low-side materials of construction Option Code 22(refer to PDS 00813-0100-4016 for more information).
(2) Not available with Option Codes Zx, V2, or V3.
(3) Not available with Output Code G or Option Code Zx.
(4) Not available with Option Codes M1–M9.(5) Not available with Output Codes G, J, L, M, or Option Code Zx.
(6) Not available with Output Codes G, J, L, M, S, or Option Code Zx.
(7) Not available with Output Codes G, L, M, or Option Code Zx.
(8) Available for the diaphragm, upper housing, flange, adapter, extension, and lower housing.(9) Not available with Option Codes Mx, Vx, Ix, or Ex, or Output Codes G, L, M, or S.
TABLE 11. (continued).
Code Options (see complete approvals descriptions)
S1(1)
M1(2)
M3(2)
M4(2)
M7(2)
E6I5(3)
K5I6(1)
C5(4)
C6(1)
K6E4E7E8I1(5)
I7(1)
I8(6)
N1(7)
N7IC(3)
W5Q4Q8(8)
V1V2V3Z1(9)
Z2(9)
Z3(9)
F_
One Remote Seal Selected from PDS 00813-0100-4016METERSLinear Meter, 0–100% ScaleSpecial Scale Meter, Specify RangeLCD Meter, 0–100%LCD Meter, Linear, Special ConfigurationHARZARDOUS LOCATIONS C ERTIFICATIONSCanadian Standards Association (CSA) Explosion-Proof ApprovalFactory Mutual (FM) Non-incendive and Intrinsic Safety ApprovalFactory Mutual (FM) Explosion-Proof and Intrinsic Safety CombinationCanadian Standards Association (CSA) Intrinsic Safety Approval Industry and Science Canada (ISC) Approval (Available in Canada Only)Combination of I6 and E6; CSA Explosion-Proof and Intrinsic Safety Approval(Requires 42.4 V dc max. power supply)CSA/CENELEC Explosion-Proof and Intrinsic Safety ApprovalJapanese Industrial Standards (JIS) Flameproof CertificationStandards Association of Australia (SAA) Flameproof CertificationCESI/CENELEC Flameproof CertificationBASEEFA Intrinsic Safety CertificationStandards Association of Australia (SAA) Intrinsic Safety CertificationCESI/CENELEC Flameproof CertificationBASEEFA Type N CertificationStandards Association of Australia (SAA) Non-incendive Safety ApprovalSchweizerischer Elektrochnischer Verein (SEV) Intrinsic Safety CertificationOTHER OPTIONSCopper O-ring for Vacuum Service (Nonwetted)Calibration Data SheetMaterial Traceability per EN 10204 3.1BReverse Output4–20 mV Test Signal20–100 mV Test Signal4-wire, 0–20 mA Output4-wire, 0–16 mA Output4-wire, 0–10 mA OutputSelect One Code from Flushing Connections Lower Housing Option Table 12.
Typical Model Number: 1 151LT 4 S A0 A 52 D F1
NOTEFM explosion-proof approval is standard.
TABLE 12. Flushing Connections Lower Housing Options. • available – not available
(1) Not available with high pressure side Option Codes A0, B0, and G0.
(2) Not available with high pressure side Option Code G0.
CodeFlushing Connection Ring Material (Lower H ousing)
Flushing Connect ions
SizeDiaphragm Size
2-in. 3-in. 4-in.
F1F2F3(1)
F4(1)
FAFC(2)
F7F8F9F0
SSTSST
Hastelloy C-276Hastelloy C-276
SSTHastelloy C-276
SSTSST
Hastelloy C-276Hastelloy C-276
1212001212
¼-18 NPT¼-18 NPT¼-18 NPT¼-18 NPT
——
½-14 NPT½-14 NPT½-14 NPT½-14 NPT
••••••••••
••••
——••••
••••
——••••
Pressure-65
Pressu
Model 1151 Alp haline ® Press ure Transmitters
Model 1151
STANDARD ACCESSORIES All models are shipped with flange adapters, drain/vent valves, and one instruction manual per shipment.Tagging The transmitter will be tagged, at no charge, in accordance with customer requirements. All tags are stainless steel. The standard tag is wired to the transmitter. Tag character height is 0.125 in. (0.318 cm). A permanently attached tag is available upon request.Calibration Transmitters are factory calibrated to the customer’s specified range. If calibration is not specified, the transmitters are calibrated at maximum range. Calibration is performed at ambient temperature and pressure.
Optional Three-Valve Manifolds Part No. 01166-0073-0001:3-valve manifold, carbon steel for DP (Ranges 6–9), HP (Ranges 6–7). (Anderson, Greenwood & Co., M4AVIC-TR-68).
Part No. 01151-0150-0002:3-valve manifold, 316 SST with carbon steel bolts for DP (Ranges 6–9), HP (Ranges 6–7). (Anderson, Greenwood & Co., M4AVIC-TR-68).
re-66
Other Related LiteratureModel 1151 Smart 1Pressure Transmitters
00813-0100-4593Model 1151DR Draft Range Differential Pressure Transmitter
00813-0100-4294Filled Systems for Pressure Transmitters
00813-0100-4016Model 1151 Smart Retrofit Kit
00813-0100-4594Rosemount, the Rosemount logotype, HART, and SMART FAMILY are registered trademarks of Rosemount Inc.d-Cell, Rosemount System 3, and RMV9000 are trademarks of Rosemount Inc.Fluorolube is a registered trademark of Hooker Chemical Co.Hastelloy is a registered trademark of Cabot Corp.Monel is a registered trademark of International Nickel Co.Viton is a registered trademark of E.I. du Pont de Nemours & Co.Neobee M-20 is a registered trademark of Stepan Chemical Co.Syltherm and D.C. are registered trademarks of Dow Corning Corp.Cover photo: 1151-001ABHART is a registered trademark of the HART Communication Foundation.d-Cell is a trademark of Rosemount Inc.Hastelloy, Hastelloy C, and Hastelloy C-276 are registered trademarks of Cabot Corp.Monel is a registered trademark of International Nickel Co.Teflon is a registered trademark of E.I. du Pont de Nemours & Co.Aflas is a registered trademark of Asahi Glass Co., Ltd.Kynar is a trademark of Pennwalt Inc.Flourolube is a registered trademark of Hooker Chemical Co.
