Multiple Display Control Protocol - samsung.com · 6 1. Overview This document provides...

SEC-VD-DSW Multiple Display Control

Multiple Display Control Protocolfor SyncMaster 820DXn 700DXn

570Dxn 460Dxn 460TXn 400DXnCopyright © 2003 2007 Samsung Electronics Co., Ltd

Copyright notice

This document is Copyright ⓒ Samsung Electronics, Co. - all rights reserved.

「 This document is the technological property of Samsung Electronics Company and the copying

and/or use of this document without permission of the Tech Document Department are prohibited.」

Contact Information

Display S/W Group, VD Business Division

Samsung Electronics Co., Ltd

Address : 416, Maetan-3Dong, YoungTong-Gu,Suwon City, Kyungki-Do, Korea442-742

Telephone : 82-31-277-2348,2325,2343E-mail : [email protected], [email protected], [email protected]

Author:: Display S/W2, Visual & Display Division.History:

Version Date Content Author Approved by

1.0 2007. 12. 10 Protocol for 400DXn, 460D(T)Xn,570Dxn, 700Dxn, 820Dxn Park Jong Won

Table of Contents

1. Overview.......................................................................................... 6

1.1. Purpose................................................................................................... 6

1.2. Scope......................................................................................................6

1.3. Terms & Abbreviations.............................................................................. 6

2. API Function ................................................................................... 7

1) MLS_HAL_I2C_Start...................................................................................... 7

2) MLS_HAL_I2C_Stop...................................................................................... 7

3) MLS_HAL_I2C_Send..................................................................................... 7

3. Events from Library & Sample Code...................................................9

1) Event from Library.......................................................................................9

2) Volume Control in Application.......................................................................9

3) When the Application Receives the Current Volume Values........................... 10

4. Command....................................................................................... 11

4.1. Detailed Description of Commands...........................................................14

1) Status Control.............................................................................................. 14

2) Time Control................................................................................................ 15

3) On Time Control........................................................................................... 16

4) Off Time Control...........................................................................................17

5) Video Control (ATV, DTV, AV, S-Video, Component, HDMI Only)..................... 18

6) Audio Control............................................................................................... 19

7) RGB Control (PC, BNC, DVI, MagicNet Only)..................................................20

8) PIP Status Control........................................................................................ 21

9) Maintenance Control..................................................................................... 22

10) Display Status Control................................................................................. 23

11) SW Version Control..................................................................................... 24

12) Model Number Control.................................................................................25

13) Power Control.............................................................................................26

14) Volume Control........................................................................................... 27

15) Mute Control...............................................................................................28

16) Input Source Control................................................................................... 29

17) Picture Size Control.................................................................................... 30

18) Direct Channel Control(ATV, DTV Only).........................................................31

19) Contrast Control (ATV, DTV, AV, S-Video, Component, HDMI Only)............... 32

20) Brightness Control (ATV, DTV, AV, S-Video, Component, HDMI Only).............33

21) Sharpness Control (ATV, DTV, AV, S-Video, Component, HDMI Only).............34

22) Color Control (ATV, DTV, AV, S-Video, Component, HDMI Only)....................35

23) Tint Control (ATV, DTV, AV, S-Video, Component, HDMI Only)...................... 36

24) Red Gain Control (PC, BNC, MagicNet Only)................................................ 37

25) Green Gain Control (PC, BNC, MagicNet Only)............................................. 38

26) Blue Gain Control (PC, BNC, MagicNet Only)................................................39

27) Treble Control.............................................................................................40

28) Bass Control...............................................................................................41

29) Balance Control.......................................................................................... 42

30) Coarse Control (PC, BNC Only)................................................................... 43

31) Fine Control (PC, BNC Only)....................................................................... 44

32) H-Position Control (PC, BNC Only).............................................................. 45

33) V-Position Control (PC, BNC Only).............................................................. 46

34) Clear Menu Control..................................................................................... 47

35) Remote Control...........................................................................................48

36) RGB Contrast Control (PC, BNC, DVI, MagicNet Only)...................................49

37) RGB Brightness Control (PC, BNC, DVI, MagicNet Only)................................50

38) PIP On / Off Control...................................................................................51

39) Auto Adjustment Control (PC, BNC Only)......................................................52

40) Color Tone Control (ATV, DTV, AV, S-Video, Component, HDMI Only)........... 53

41) Color Temp Control.....................................................................................54

42) PIP Source Control .................................................................................... 55

43) Main-PIP Swap Control............................................................................... 56

44) PIP Size Control..........................................................................................57

45) PIP Locate Control......................................................................................58

46) Sound Select Control.................................................................................. 59

47) Auto Lamp Control......................................................................................60

48) Manual Lamp Control.................................................................................. 61

49) Safety Screen Control ................................................................................ 62

50) Video Wall Mode Control............................................................................. 63

51) Safety Lock................................................................................................ 64

52) Panel Lock................................................................................................. 65

53) OSD On/Off................................................................................................66

54) P.Mode Control...........................................................................................67

55) S.Mode Control...........................................................................................68

56) NR Mode Set (ATV, DTV, AV, S-Video, Component, HDMI Only)....................69

57) PC Color Tone Control (PC, BNC , DVI, MagicNet only)................................70

58) Auto AutoAdjustment................................................................................... 71

59) All Keys Lock..............................................................................................72

60) SRS TSXT Control....................................................................................... 73

61) Film Mode Control...................................................................................... 74

62) Signal Balance (PC,BNC Only)..................................................................... 75

63) SB Gain (PC,BNC Only)...............................................................................76

64) SB Sharpness (PC,BNC Only)...................................................................... 77

65) Panel On Time .......................................................................................... 78

66) Video Wall On.............................................................................................79

67) Temperature Control.................................................................................... 80

68) Brightness Sensor....................................................................................... 81

69) Dynamic Contrast(ATV, DTV, AV, S-Video, Component, HDMI Only)............... 82

70) Safety Screen On........................................................................................83

71) Video Wall Control...................................................................................... 84

72) Model Name Control....................................................................................85

73) MagicNet PIP (MagicNet Only)..................................................................... 86

74) Panel ON/OFF............................................................................................ 89

6

1. OverviewThis document provides explanations of the MDC(Multiple Display Control) Protocolsusing the networks.

1.1. PurposeThis document provides an explanation of the software architecture commands and the data required formonitor control or status check. the network board utilizes Windows XPe which uses HAL API system.This document is designed for the Windows XPe application software programmer , system softwareengineer and tester (Programmer , Developer, Tester)

1.2. ScopeThis document provides explanations of the protocols for network monitor control and status check. thenetwork board has installed Windows XPe application that includes access for monitor check and controlusing the HAL API system. This document does not covers communications between the network boardHAL software and the main board firmware, and communications between the network board and theserver.

1.3. Terms & Abbreviations

MDC Multiple Display Control

ProtocolA Communications protocol is used to communications in this case between thenetwork board HAL (Hardware Abstract Layer) and the Windows XPe Operatingsystem

HAL Hardware Abstract Layer

API Application Programming Interface

7

2. API FunctionExplains the APIs required for transferring data to and from the application .

1) MLS_HAL_I2C_Start● ProtocolDWORD MLS_HAL_I2C_Start(void)

● ParameterNone

● Return ValueFALSE : Failed to start communications.TRUE : Communications started.

● ExplanationStarts communicating with the monitor. If you want to communicate with the monitor firmware, you shouldperform this function first, or communicating will fail.

2) MLS_HAL_I2C_Stop● ProtocolDWORD MLS_HAL_I2C_Stop(void)

● ParameterNone

● Return ValueFALSE : Terminating communications failed.TRUE : Communications terminated.

● ExplanationTerminates communications with the monitor. If you want to end communicating with the moniter firmware,you should perform this function.

3) MLS_HAL_I2C_Send

● ProtocolDWORD MLS_HAL_I2C_Send(UCHAR *lpBuff, UCHAR length)

● ParameterUCHAR *lpBuff : Data transfer to the monitor firmwareUCHAR length : lpBuff data length

8

● Return ValueFALSE : Data transfer failedTRUE : Data transferred

● ExplanationTransfers data to the monitor.

9

3. Events from Library & Sample Code

1) Event from Library

Library sends an event to the application when it receives data from the firmware. The event is aWindows message,[::RegisterWindowMessage(_T("MSG_MDC_COMM"))]. However the applicationshould respond to this [::RegisterWindowMessage(_T("MSG_MDC_COMM"))].Windows message before it can receive data from library.

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x12 Volume

Library transfers commands and data lengths to WPARAM, a Windows message parameter. However ,Library sends data lengths other than the Command (0xFF) to higher-byte WPRAMs and transfers themother than the Check Sum to lower-byte WPRAMs.

Ack/Nak Contents0x00 NAK0x01 ACK

☞ Note : For WPARAM commands of the [::RegisterWindowMessage(_T("MSG_MDC_COMM"))]Windows Message, 0xFF is an MDC event while 0x11 is a remote control event for the monitor.This document does not enter further into this as this belongs to MDC documentation. The remotecontrol signals are mentioned separately in our documents.

2) Volume Control in Application

The data format mentioned in '4.1 Detailed Description of Commands' below is as follows.

Command Data Length Data 10x12 1 Volume

The application can only retrieve data that corresponds to the parameter.

● Sample Code

#define CMD_VOLUME 0x12{

UCHAR SendBuff[3] = {0, 0, 0};SendBuff[0] = CMD_VOLUME; //Volume Control CommandSendBuff[1] = 0x01; //Data LengthSendBuff[2] = data; //Volume Data

DWORD dRetSend = MLS_HAL_I2C_Send(SendBuff, 3);}

10

3) When the Application Receives the Current Volume Values

For command explanations mentioned below, the data formats are as follows. Library receives datain the formats described below.


When library receives data from the firmware, it sends a Windows Message[::RegisterWindowMessage(_T("MSG_MDC_COMM"))] for confirmation, and transfers commands and datalengths to WPARAM, a Windows message parameter.

When the application receives the [::RegisterWindowMessage(_T("MSG_MDC_COMM"))] Windows Messageabove, it can translate WPARAM and get the data that library received from the firmware.

● Sample Code

const UINT MDC_COMM_MSG = ::RegisterWindowMessage(_T("MSG_MDC_COMM"));#define CMD_VOLMUE 0x12

WindowProc(UINT message, WPARAM wParam, LPARAM lParam){

if(message == MDC_COMM_MSG)//The Message that library receives data from the firmware{

unsigned char* ReadBuff = (PUCHAR)wParam;

if(ReadBuff[0] == 0xFF) //MDC Command{

if((ReadBuff[2] == 0x01) // Replied data is ACK{

if (ReadBuff[3] == CMD_VOLMUE) ) // Volume Data is receivedShowVolume(ReadBuff[4]);

}}

11

4. Command

No Type of Command Command Range of Value(Decimal)

1 Status Control 0x00 -

2 Time Control 0x01 -

3 On Time Control 0x02 -

4 Off Time Control 0x03 -

5 Video Control 0x04 -

6 Audio Control 0x05 -

7 RGB Control 0x06 -

8 PIP Status Control 0x07 -

9 Maintenance Control 0x08 -

10 Display Status Control 0x0D

11 SW Version Control 0x0E

12 Model Number Control 0x10 -

13 Power Control 0x11 0 ~ 1

14 Volume Control 0x12 0 ~ 100

15 Mute Control 0x13 0 ~ 1

16 Input Source Control 0x14 -

17 Image Size Control 0x15 -

18 Direct Channel Control 0x17 -

19 Contrast Control 0x24 0 ~ 100

20 Brightness Control 0x25 0 ~ 100

21 Sharpness Control 0x26 0 ~ 100

22 Color Control 0x27 0 ~ 100

23 Tint Control 0x28 0 ~ 100

24 Red Gain Control 0x29 0 ~ 100

25 Green Gain Control 0x2A 0 ~ 100

26 Blue Gain Control 0x2B 0 ~ 100

27 Treble Control 0x2C 0 ~ 100

28 Bass Control 0x2D 0 ~ 100

29 Balance Control 0x2E 0 ~ 100

30 Coarse Control 0x2F 0 ~ 1

31 Fine Control 0x30 0 ~ 1

32 H-Position Control 0x31 0 ~ 1

12

33 V-Position Control 0x32 0 ~ 1

34 Clear Menu Control 0x34 0

35 Remote Control 0x36 0 ~ 1

36 RGB Contrast Control 0x37 0 ~ 100

37 RGB Brightness Control 0x38 0 ~ 100

38 PIP On/Off Control 0x3C 0 ~ 1

39 Auto Adjustment Control 0x3D 0

40 Color Tone Control 0x3E 0 ~ 4

41 Color Temperature Control 0x3F 0 ~ 10

42 PIP Source Control 0x40 -

43 Main-PIP Swap Control 0x41 0 ~ 1

44 PIP Size Control 0x42 -

45 PIP Locate Control 0x43 0 ~ 4

46 Sound Select Control 0x47 0 ~ 1

47 Auto Lamp Control 0x57 -

48 Manual Lamp Control 0x58 0 ~ 100

49 Safety Screen Control 0x5B -

50 Video Wall Mode Control 0x5C 0 ~ 1

51 Safety Lock 0x5D 0 ~ 1

52 Panel Lock 0x5F 0 ~ 1

53 OSD On/Off 0x70 0 ~ 1

54 P. Mode Control 0x71 -

55 S. Mode Control 0x72 0 ~ 4

56 NR Mode Set 0x73 0 ~ 1

57 PC Color Tone Control 0x75 0 ~ 3

58 Auto AutoAdjustment 0x76 0 ~ 1

59 All Keys Lock 0x77 0 ~ 1

60 SRS TSXT Control 0x78 0 ~ 1

61 Film Mode 0x79 0 ~ 1

62 Signal Balance 0x7A 0 ~ 1

63 SB Gain 0x7E 0 ~ 100

64 SB Sharpness 0x7F 0 ~ 100

65 Panel On Time 0x83 -

66 Video Wall On 0x84 0 ~ 1

67 Temperature Control 0x85 0 ~ 125

68 Brightness Sensor 0x86 0 ~ 1

13

69 Dynamic Contrast 0x87 0 ~ 1

70 Safety Screen On 0x88 1 ~ 5

71 Video Wall User Control 0x89 -

72 Model Name Control 0x8A -

73 MagicNet PIP 0xE0 -

74 Panel On/Off 0xF9 0 ~ 1

☞ Note : "-" indicates when the values to be set are multiple.See "4.1. Detailed Description of Commands" for details

14

4.1. Detailed Description of Commands

1) Status Control

● FunctionThe Computer shows the current settings for the TV/Monitor.

● Get Status

Command Data Length

0x00 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 9 'A' 0x00 Power Volume

Val 3 Val 4 Val 5 Val 6 Val 7 CheckSumMute Input Aspect N Time NF F Time NF

Power : The Power Code for the TV / MonitorVolume : The Volume value for the TV / Monitor ( 0 ~ 100 )Mute : The Mute Code for the TV / MonitorInput : The Input Source Code for the TV / MonitorAspect : The Image Size Code for the TV / MonitorN Time NF : On Time On/Off value for the TV / MonitorF Time NF : Off Time On/Off value for the TV / Monitor

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x00 ERR

ERR : Error Code that shows the type of the error that occurrederror that occurred.

0 Check Sum Error1 Others

15

2) Time Control

● FunctionThe Computer controls the current the for the TV/Monitor

● Get Time Status

Command Data Length

0x01 0

● Set Time

Command Data Length Data 1 Data 2 Data 3 Data 40x01 5 AP Time H Time M Time 0

Data 50

AP Time : The AM/PM value for the TV / Monitor

1 AM0 PM

H Time : The Hour Value for the TV / Monitor ( 1 ~ 12 )M Time : The Minute Value for the TV / Monitor ( 0 ~ 59 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 7 'A' 0x01 AP Time H Time

Val 3 Val 4 Val 5 CheckSumM Time 0 0

AP Time, H Time, M Time : Same as above

● Nak


ERR : Error Code that shows the type of the error that occurrederror that occurred

16

3) On Time Control

● FunctionThe Computer controls when the TV / Monitor turns on.

● Get On Time Status

Command Data Length

0x02 0

● Set On Time

Command Data Length Data 1 Data 2 Data 3 Data 40x02 6 N AP Time N H Time N M Time N Time VR

Data 5 Data 6N Time NF N Time SC

N AP Time : The On Time AM/PM value for the TV / Monitor.

1 AM0 PM

N H Time : The On Time Hour Value for the TV / Monitor ( 1 ~ 12 )N M Time : The On Time Minute Value for the TV / Monitor ( 0 ~ 59 )N Time VR : The On Time Volume for the TV / Monitor ( 0 ~ 100 )N Time NF : The On Time On/Off value for the TV / Monitor

1 On Time ON0 On Time OFF

N Time SC : The source value for the On Time Control(See 'Input Source Control ')

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 8 'A' 0x02 N AP Time N H Time

Val 3 Val 4 Val 5 Val 6 CheckSumN M Time N Time VR N Time NF N Time SC

N AP Time, N H Time, N M Time, N Time VR, N Time NF, N Time SC : Same as above

● Nak


ERR : Error Code that shows the type of the error that occurrederror that occurred

17

4) Off Time Control

● FunctionThe Computer controls when the The Computer turn off.

● Get Off Time Status

Command Data Length

0x03 0

● Set Off Time

Command Data Length Data 1 Data 2 Data 3 Data 40x03 6 F AP Time F H Time F M Time 0

Data 5 Data 6F Time NF 0

F AP Time : The Off Time AM/PM value for the TV / Monitor

1 AM0 PM

F H Time : The Off Time Hour Value for the TV / Monitor ( 1 ~ 12 )F M Time : The Off Time Minute Value for the TV / Monitor ( 0 ~ 59 )F Time NF: The Off Time On/Off value for the TV / Monitor.

1 Off Time ON0 Off Time OFF

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 8 'A' 0x03 F AP Time F H Time

Val 3 Val 4 Val 5 Val 6 CheckSumF M Time 0 F Time NF 0

F AP Time, F H Time, F M Time, F Time NF : Same as above

● Nak


ERR : Error Code that shows the type of the error that occurred

18

5) Video Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer shows the screen settings for the TV / Monitor

● Get Video Status

Command Data Length

0x04 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x0A 'A' 0x04 Contrast Brightness

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8CheckSumSharpnes

s Color Tint ColorTone ColorTemp 0

Contrast, Brightness, Sharpness, Color, Tint, ColorTone, ColorTemp : Same as above

● Nak



19

6) Audio Control

● FunctionThe Computer controls the audio settings for the TV/ Monitor.

● Get Audio Status

Command Data Length

0x05 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x05 'A' 0x05 Treble Bass

Val 3 CheckSumBalance

Treble, Bass, Balance : Same as above

● Nak

Header Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xAA 0xFF 3 'N' 0x05 ERR


20

7) RGB Control (PC, BNC, DVI, MagicNet Only)

● FunctionThe Computer controls the screen settings of the TV / Monitor.

● Get Video Status

Command Data Length

0x06 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x0A 'A' 0x06 Contrast Brightness

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 CheckSumColorTone ColorTemp 0 Red Gain Green Gain Blue Gain

Contrast, Brightness, Red, Green, Blue : Same as above

● Nak



21

8) PIP Status Control

● FunctionThe Computer shows the PIP settings for TV / Monitor.

● Get PIP Status

Command Data Length

0x07 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 6 'A' 0x07 P.Size P.Source

Val 3 Val 4 CheckSum0 0

P.Size : The PIP size Value Code of the TV / Monitor

0x00 PIP Off0x06 Large0x08 Small0x04 Double 10x05 Double 20x09 Double 3

P.Source : The PIP Source Value Code of the TV / Monitor

● Nak



22

9) Maintenance Control● FunctionThe Computer shows the maintenance setting of the TV / Monitor

● Get Maintenance Status

Command Data Length

0x08 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x15 'A' 0x08 Power P.Size

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8P.Source LMax_H LMax_M LMax_AP LMaxValue LMin_H

Val 9 Val 10 Val 11 Val 12 Val 13 Val 14LMin_M LMin_AP LMinValue LampValue ScreenInterval ScreenTime

Val 15 Val 16 Val 17 Val 18 Val 19 Check

SumScreenType V.Wall V.WallFormat V.WallDivid V.WallSet

Power : The Power Code for the TV / MonitorP.Size : The value code for the PIP Size of the TV / MonitorP.Source : The value code for the PIP Source of the TV / MonitorLMax_H : The value code for the Auto Lamp Max Time Hour of the TV / Monitor (1 ~ 12)LMax_M : The value code for the Auto Lamp Max Time Minute of the TV / Monitor (0 ~ 59)LMax_AP : The value code for the Auto Lamp Max Time AM/PM of the TV / MonitorLMaxValue : The value code for the Auto Lamp Max value of the TV / Monitor (0 ~ 100)LMin_H : The value code for the Auto Lamp Min Time Hour of the TV / Monitor (1 ~ 12)LMin_M : The value code for the Auto Lamp Min Time Minute of the TV / Monitor (0 ~ 59)LMin_AP : The value code for the Auto Lamp Min Time AM/PM of the TV / MonitorLMinValue : The value code for the Auto Lamp Min Value of the TV / Monitor (0 ~ 100, 0xFF)LampValue : The value code for the Manual Lamp Control value of the TV / Monitor (0 ~ 100, 0xFF)ScreenInterval : The value code for the Safety Screen Interval of the TV/Monitor(Per Hour, 0(Off) ~ 10)ScreenTime : The value code for the Safety Screen Time of the TV / Monitor (0(Off) ~ 5)ScreenType : The value code for the Safety Screen Type of the TV / Monitor (3 ~ 6)V.Wall : The value code for the Video Wall Mode of the TV / MonitorV.WallFormat : The value code for the Video Wall Format of the TV / MonitorV.WallDivid : The value code for the Video Wall Divider of the TV / MonitorV.WallSet : The value code for the Video Wall Set Number of the TV / MonitorNote : if LMinValue returns to 0xFF, it means Auto Lamp Control is in off modeIf LampValue returns to 0xFF, it means Maunal Lamp Control is in off mode.

● Nak



23

10) Display Status Control● FunctionThe Computer shows the Display status of the TV / Monitor

● Get Display status

Command0x0D

Data Length

0

● Ack

Command DataLength Ack/Nak r-CMD Val 1 Val 2

0xFF 0x08 'A' 0x0D Lamp Temperature

Val 3 Val 4 Val 5 Val 6 Check

SumBright_Sensor No_Sync Cur_Temp Fan

Lamp : The Error code for the lamp of the TV / Monitor (0 : Normal, 1: Error)Temperature : The Error code for the temperature of the TV / Monitor (0 : Normal, 1: Error)Bright_Sensor : The Error code for the Bright Sensor of the TV / Monitor (0 : Normal, 1: Error)No_Sync : The Error code for the Sync of the TV / Monitor (0 : Normal, 1: Error)Cur_Temp : The value code for the Current Temperature of the TV / MonitorFan : The Error code for the Fan of the TV / Monitor (0 : Normal, 1: Error)

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x0D ERR


24

11) SW Version Control

● FunctionThe Computer shows the version information of the TV / Monitor

● Get SW Version

Command Data Length

0x0E 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x11 'A' 0x0E Version1 Version2

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8

Version3 Version4 Version5 Version6 Version7 Version8

Val 9 Val 10 Val 11 Val 12 Val 13 Val 14Version9 Version10 Version11 Version12 Version13 Version14

Val 15 Check

SumVersion1

Version1 ~ Version11 : The Project Info of the TV / MonitorVersion12 ~ Version15 : The SW Version of the TV / Monitor

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x0E ERR


25

12) Model Number Control

● FunctionThe Computer identifies and display the TV / Monitor's Model Number.

● Get Model Number Status

Command Data Length

0x10 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 2 Val 3 CheckSum0xFF 0x05 'A' 0x10 Species Model 0

Species : Type of panel used used for the TV / Monitor

0x01 PDP0x02 LCD0x03 DLP

Model : TV / Monitor's model name

0x01 PPM50H20x02 PPM42S20x03 PS-42P2ST0x04 PS-50P2HT0x05 SyncMaster 400T0x06 SyncMaster 403T0x07 PPM42S3, SPD-42P3SM0x08 PPM50H3, SPD-50P3HM0x09 PPM63H3, SPD-63P3HM0x0A PS-42P3ST0x0B SyncMaster 323T0x0C SyncMaster 403T - CT40CS(N)0x0D PPMxxM5x

0x0ESyncMaster 320P(n)SyncMaster 400P(n)

SyncMaster 4600P(n)

● Nak



0x10

SyncMaster 320PX

SyncMaster 460PX(n)

SyncMaster 400PX(n)

0x13SyncMaster 400TX(n)

0x14 SyncMaster 570DX(n)

0x15

SyncMaster 320DX

SyncMaster 820DX(n)

SyncMaster 700DX(n)

SyncMaster 400DX(n)

SyncMaster 460DX(n)

0x16 SyncMaster 460TX(n)

26

13) Power Control

● FunctionThe Computer turns the TV / Monitor ON/OFF.

● Get Power ON/OFF Status

Command Data Length

0x11 0

● Set Power ON/OFF

Command Data Length Data 10x11 1 Power

Power : The Power Code for the TV / Monitor

1 Power ON0 Power OFF

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x11 Power

Power : Same as above

● Nak



27

14) Volume Control

● FunctionThe Computer changes the Volume level of the TV / Monitor의 Volume.

● Get Volume Status

Command Data Length

0x12 0

● Set Volume

Command Data Length Data 10x12 1 Volume

Volume : The Volume level value Code of the TV / Monitor ( 0 ~ 100 )

● Ack


Volume : Same as above

● Nak



28

15) Mute Control

● FunctionThe Computer turns the Mute of the TV / Monitor

● Get Mute ON/OFF Status

Command Data Length

0x13 0

● Set Mute ON/OFF

Command Data Length Data 10x13 1 Mute

Mute : The Mute Code of the TV / Monitor

1 Mute ON0 Mute OFF

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x13 Mute

Mute : Same as above

● Nak



29

16) Input Source Control

● FunctionThe Computer changes the Input Source of the TV / Monitor.

● Get Input Source Status

Command Data Length

0x14 0

● Set Input Source

Command Data Length Data 10x14 1 Input

Input : The Input Source Code for the TV / Monitor

0x14 PC0x1E BNC0x18 DVI0x0C AV0x04 S-Video0x08 Component0x20 MagicNet0x21 HDMI0x30 TV0x40 DTV

Note : TV/DTV → TV only

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x14 Input

Input : Same as above

● Nak



30

17) Picture Size Control

● FunctionThe Computer changes the Aspect Ratio of the TV / Monitor screen.

● Get Picture Size Status

Command Data Length

0x15 0

● Set Picture Size

Command Data Length Data 10x15 1 Aspect

Aspect : The Picture Size Code for the TV / Monitor

PC, BNC, DVI0x10 16 : 90x18 4 : 3TV, AV, S-VIdeo, Component, HDMI0x00 Auto Wide0x01 16 : 90x05 Zoom 10x06 Zoom 20x0B 4 : 3

Note : Some Image Size may not available in input signal mode of 720p, 1080iAuto Wide → TV only

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x15 Aspect

Aspect : Same as above

● Nak



31

18) Direct Channel Control(ATV, DTV Only)

● FunctionThe Computer controls the Channel of TV.

● Get Direct Channel status

Command0x17

Data Length

0

● Set Direct Channel

Command Data Length Data 1 Data 2 Data 3 Data 4 Data 5

0x17 8 Country ATV_DTV AirCable CH_NUMHigh_Byte

CH_NUMLow_Byte

Data 6 Data 7 Data 8

Sel_Monitor Minor_CHHigh_Byte

Minor_CHLow_Byte

● Ack

Command DataLength Ack/Nak r-CMD Val 1 Val 2

0xFF 0x0A 'A' 0x17 Country ATV_DTV

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 Check

SumAirCable CH_NUMHigh_Byte

CH_NUMLow_Byte Sel_Monitor Minor_CH

High_ByteMinor_CHLow_Byte

Country : The value code for the country of the TV / Monitor (0 : Korea, 1: U.S.A, ...)ATV_DTV : The value code for the ATV/DTV of the TV / Monitor (0 : Analog TV, 1: Digital TV)AirCable : The value code for the Air/Cable of the TV / Monitor (0 : Air, 1: Cable)CH_NUM High_Byte : The value code for the Major Channel High-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)CH_NUM Low_Byte : The value code for the Major Channel Low-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)Sel_Minor : The value code for the Minor Channel Enable/Disable of the TV / Monitor

(0 : Enable, 1 : Disable)(DTV Only)Minor_CH High_Byte : The value code for the Minor Channel High-Byte of the TV / Monitor

(0 ~ 999)(DTV Only)Minor_CH Low_Byte : The value code for the Minor Channel Low-Byte of the TV / Monitor

(0 ~ 999)(DTV Only)

● Nak



32

19) Contrast Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjusts the Contrast of the TV / Monitor.

● Get Contrast Status

Command Data Length

0x24 0

● Set Contrast

Command Data Length Data 10x24 1 Contrast

Contrast : The Contrast Value Code of the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x24 Contrast

Contrast : Same as above

● Nak



33

20) Brightness Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjusts the Brightness settings of the TV / Monitor

● Get Brightness Status

Command Data Length

0x25 0

● Set Brightness

Command Data Length Data 10x25 1 Brightness

Brightness : The Brightness value code for the TV / Monitor( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x25 Brightness

Brightness : Same as above

● Nak



34

21) Sharpness Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjusts the Sharpness of the TV / Monitor.

● Get Sharpness Status

Command Data Length

0x26 0

● Set Sharpness

Command Data Length Data 1

0x26 1 Sharpness

Sharpness : The Sharpness Value Code for the TV / Monitor ( 0 ~ 100 )Note : Sharpness can be set up within 50 Step(0, 2, 4, 6... 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1CheckSum0xFF 3 'A' 0x26 Sharpnes

s

Sharpness : Same as above

● Nak



35

22) Color Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjusts the Color settings of the TV / Monitor.

● Get Color Status

Command Data Length

0x27 0

● Set Color

Command Data Length Data 10x27 1 Color

Color : The Color Value Code for the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x27 Color

Color : Same as above

● Nak



36

23) Tint Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjusts the Tint of the TV / Monitor when the video format is NTSCNote : It does not work in PAL signal.

● Get Tint Status

Command Data Length

0x28 0

● Set Tint

Command Data Length Data 10x28 1 Tint

Tint : The Tint Value Code for the TV / Monitor ( 0 ~ 100 )

R Tint ValueG (100 - Tint) Value

Note : Tint can be set up within 50Step (0, 2, 4, 6... 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x28 Tint

Tint : Same as above

● Nak



37

24) Red Gain Control (PC, BNC, MagicNet Only)

● FunctionThe Computer adjusts the Red Gain of the TV / Monitor.

● Get Red Gain Status

Command Data Length

0x29 0

● Set Red Gain

Command Data Length Data 10x29 1 Red

Red : The Red Gain Value Code for the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x29 Red

Red : Same as above

● Nak



38

25) Green Gain Control (PC, BNC, MagicNet Only)

● FunctionThe Computer adjusts the Green Gain of the TV / Monitor

● Get Green Gain Status

Command Data Length

0x2A 0

● Set Green Gain

Command Data Length Data 10x2A 1 Green

Green : The Green Gain Value Code of the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2A Green

Green : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x2A ERR


39

26) Blue Gain Control (PC, BNC, MagicNet Only)

● FunctionThe Computer adjusts the Blue Gain of the TV / Monitor.

● Get Blue Gain Status

Command Data Length

0x2B 0

● Set Blue Gain

Command0x2B

Blue : The Blue Gain Value Code of the TV / Monitor( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2B Blue

Blue : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x2B ERR


40

27) Treble Control

● FunctionThe Computer adjusts the Treble of the TV / Monitor.

● Get Treble Status

Command Data Length

0x2C 0

● Set Treble

Command Data Length Data 10x2C 1 Treble

Treble : The Trable Value Code for the TV / Monitor ( 0 ~ 100 )Note : Treble can be set up within 40 Step. (0, 2, 5, 7... 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2C Treble

Treble : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x2C ERR


41

28) Bass Control

● FunctionThe Computer adjusts the Bass of the TV / Monitor.

● Get Bass Status

Command Data Length

0x2D 0

● Set Bass

Command Data Length Data 10x2D 1 Bass

Bass : The Bass Value Code for the TV / Monitor( 0 ~ 100 )Note : Bass can be set up within 40 Step (0, 2, 5, 7... 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2D Bass

Bass : Same as above

● Nak



42

29) Balance Control

● FunctionThe Computer adjusts the Balance settings of the TV / Monitor.

● Get Balance Status

Command Data Length

0x2E 0

● Set Balance

Command Data Length Data 10x2E 1 Balance

Balance : The Balance Value Code for the TV / Monitor ( 0 ~ 100 )

L (100 - Balance) ValueR Balance Value

Nots : Balance can be set up within 22 Step (0, 4, 9, 13... 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2E Balance

Balance : Same as above

● Nak



43

30) Coarse Control (PC, BNC Only)

● FunctionThe Computer adjusts the Coarse settings of the TV / Monitor.

● Get Coarse StatusNone

● Set Coarse

Command Data Length Data 10x2F 1 Coarse

Coarse : The Frequency Increase/Decrease Code for the TV / Monitor

1 Increase0 Decrease

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x2F Coarse

Coarse : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x2F ERR


44

31) Fine Control (PC, BNC Only)

● FunctionThe Computer adjusts the Fine settings of the TV / Monitor.

● Get Fine StatusNone

● Set Fine

Command Data Length Data 10x30 1 Fine

Fine : The Phase Increase/Decrease Code for the TV / Monitor

1 Increase0 Decrease

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x30 Fine

Fine : Same as above

● Nak



45

32) H-Position Control (PC, BNC Only)

● FunctionThe Computer adjusts the Horizontal Position settings of the TV / Monitor.

● Get H-Position StatusNone

● Set H-Position

Command Data Length Data 10x31 1 H-Pos

H-Pos : The H-Position Increase/Decrease Code for the TV / Monitor

1 Shift to the right0 Shift to the left

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x31 H-Pos

H-Pos : Same as above

● Nak



46

33) V-Position Control (PC, BNC Only)

● FunctionThe Computer adjusts the Vertical Position settings of the TV / Monitor.

● Get V-Position StatusNone

● Set V-Position

Command Data Length Data 10x32 1 V-Pos

V-Pos : The V-Position Increase/Decrease Code for the TV / Monitor

1 Shift to the right0 Shift to the left

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x32 V-Pos

V-Pos : Same as above

● Nak



47

34) Clear Menu Control

● FunctionThe Computer exits the Menu OSD on the TV / Monitor

● Get Clear Menu StatusNone

● Set Clear Menu

Command Data Length Data 10x34 1 Clear

Clear : 0x00 (Always)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x34 Clear

● Nak



48

35) Remote Control

● FunctionThe Computer enables and disables the IR reception feature of the TV/Monitor remoteThis functions independently of the Power On/Off

● Get Remote Status

Command Data Length

0x36 0

● Set Remote Enable/Disable

Command Data Length Data 10x36 1 RMC

RMC : Reception (status) Enable/Disable Code for the TV / Monitor Remote

1 Remocon Enable0 Remocon Disable

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x36 RMC

RMC : Same as above

● Nak



49

36) RGB Contrast Control (PC, BNC, DVI, MagicNet Only)

● FunctionThe Computer adjusts the Contrast settings of the TV / Monitor when the Aspect is RGB

● Get Contrast Status

Command Data Length

0x37 0

● Set Contrast

Command Data Length Data 10x37 1 Contrast

Contrast : The RGB Contrast Value Code for the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x37 Contrast

Contrast : Same as above

● Nak



50

37) RGB Brightness Control (PC, BNC, DVI, MagicNet Only)

● FunctionThe Computer adjusts the Brightness settings of the TV / Monitor when the Aspect is RGB

● Get Brightness Status

Command Data Length

0x38 0

● Set Brightness

Command Data Length Data 10x38 1 Brightness

Brightness : The RGB Brightness Value Code for the TV / Monitor ( 0 ~ 100 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x38 Brightness

Brightness : Same as above

● Nak



51

38) PIP On / Off Control

● FunctionThe Computer turns the PIP function of the TV / Monitor ON/OFF.This function is not avaliable for MagicNet Mode

● Get PIP ON/OFF Status

Command Data Length

0x3C 0

● Set PIP ON/OFF

Command Data Length Data 10x3C 1 PIP

PIP : PIP On/Off Code for the TV / Monitor

1 PIP ON0 PIP OFF

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x3C PIP

PIP : Same as above

● Nak



52

39) Auto Adjustment Control (PC, BNC Only)

● FunctionThe Computer adjusts the RGB Screen settings of the TV / Monitor.

● Get Auto Adjustment StatusNone.

● Set Auto Adjustment

Command Data Length Data 10x3D 1 Auto

Auto : 0x00 (Always)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x3D Auto

● Nak



53

40) Color Tone Control (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer adjust the Color Tone setting of the TV / Monitor.

● Get Color Tone Status

Command Data Length

0x3E 0

● Set Color Tone

Command Data Length Data 10x3E 1 Color Tone

Color Tone : The Color Tone Value Code for the TV / Monitor( 0 ~ 4 )

0x00 Cool 20x01 Cool 10x02 Normal0x03 Warm 10x04 Warm 20x50 Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x3E Color Tone

Color Tone : Same as above

● Nak



54

41) Color Temp Control

● FunctionThe Computer adjust the Color Temp setting of the TV / Monitor.This function is only available that Color Tone value is 'OFF'

● Get Color Temp Status

Command Data Length

0x3F 0

● Set Color Tone

Command Data Length Data 10x3F 1 Color Temp

Color Temp : The Color Temp Value Code for the TV / Monitor( 0 ~ 10 )

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x3F Color Temp

Color Temp : Same as above

● Nak



55

42) PIP Source Control● FunctionThe Computer adjusts the PIP Source of the TV / Monitor.Available only when the PIP function is On. Not available in MagicNet

● Get PIP Source Status

Command Data Length

0x40 0

● Set PIP Source

Command Data Length Data 10x40 1 P.Source

P.Source : The Input source Code for the TV / MonitorChanging the PIP source may not be available depending on the main source.See table below.<460Txn Model>

PC DVI TV/DTV AV S-Video Component HDMIPC X X X ○ ○ ○ XDVI X X X ○ ○ ○ X

TV/DTV X X X X X X XAV ○ ○ X X X X X

S-Video ○ ○ X X X X XComponent ○ ○ X X X X X

HDMI X X X X X X X

<400/460/570/700/820Dxn Model>

PC BNC DVI DVI_VIDEO AV S-Video Component HDMIPC X X X X ○ ○ ○ ○

BNC X X X X ○ ○ X ○

DVI X X X X ○ ○ ○ XDVI_VIDEO X X X X ○ ○ ○ X

AV ○ ○ ○ ○ X X X XS-Video ○ ○ ○ ○ X X X X

Component ○ X ○ ○ X X X XHDMI ○ ○ X X X X X X

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x40 P.Source

P.Source : Same as above● Nak



56

43) Main-PIP Swap Control

● FunctionThe Computer swap the main screen with the PIP screen.Not available in MagicNet.

● Get Main-PIP Swap StatusNone.

● Set Main-PIP Swap

Command Data Length Data 10x41 1 Swap

Swap : 0x00 (Always)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x41 Swap

● Nak



57

44) PIP Size Control

● FunctionThe Computer changes the PIP size of the TV / Monitor.Not available in MagicNet.

● Get PIP Size Status

Command Data Length

0x42 0

● Set PIP Size

Command Data Length Data 10x42 1 P.Size

P.Size : The PIP Size Value Code for the TV / Monitor.

0x00 PIP Off0x06 Large0x08 Small0x04 Double 10x05 Double 20x09 Double 3

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x42 P.Size

P.Size : Same as above

● Nak



58

45) PIP Locate Control

● FunctionThe Computer adjusts the PIP position of the TV / Monitor.Not available in MagicNet.

● Get PIP Locate StatusNone

● Set PIP Locate

Command Data Length Data 10x43 1 P.Locate

P.Locate : The value code for PIP LOCATE of the TV / Monitor

0 PIP Off(Get Only)1 Upper Left2 Upper Right3 Lower Right4 Lower Left

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x43 P.Locate

P.Locate : Same as above

● Nak



59

46) Sound Select Control

● FunctionThe Computer adjust the Sound Settings of the TV/Monitor when the PIP function ison.

● Get Sound select

Command Data Length

0x47 0

● Set Sound select

Command Data Length Data 10x47 1 S.Select

S.Select : The Sound select Code for TV / Monitor

1 Main0 Sub

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x47 S.Select

S.Select : Same as above

● Nak



60

47) Auto Lamp Control

● FunctionThe Computer adjusts the Auto Lamp Function Settings of the TV / Monitor.When Manual Lamp Control is set to ON, Auto Lamp Control is turned Off automatically.

● Get Auto Lamp

Command Data Length

0x57 0

● Set Auto Lamp

Command Data Length Data 1 Data 2 Data 3 Data 40x57 8 LMax_H LMax_M LMax_AP LMaxValue

Data 5 Data 6 Data 7 Data 8LMin_H LMin_M LMin_AP LMinValue

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 20xFF 0x0A 'A' 0x57 LMax_H LMax_M

Val 3 Val 4 Val 5 Val 6 Val 7 Val 8 CheckSumLMax_AP LMaxValue LMin_H LMin_M LMin_AP LMinValue

LMax_H : The value code for the Auto Lamp Max Time Hour of the TV / Monitor.(1 ~ 12)LMax_M : The value code for the Auto Lamp Max Time Minute of the TV / Monitor.(0 ~ 59)LMax_AP : The value code for the Auto Lamp Max Time AM/PM of the TV / Monitor.LMaxValue : The value code for the Auto Lamp Max Value of the TV / Monitor. (0 ~ 100)LMin_H : The value code for the Auto Lamp Min Time Hour of the TV / Monitor. (1 ~ 12)LMin_M : The value code for the Auto Lamp Min Time Minute of the TV / Monitor. (0 ~ 59)LMin_AP : The value code for the Auto Lamp Min Time AM/PM of the TV / Monitor.LMinValue : The value code for the Auto Lamp Min Value of the TV / Monitor.(0 ~ 100)Note : If LMinValue returns to 0xFF, it means Auto Lamp Control is in OFF mode.

If Dynamic contrast is set to on, Auto Lamp Control is not work.

● Nak



61

48) Manual Lamp Control

● FunctionThe Computer adjusts the Manual Lamp Function settings of the TV / Monitor.When Auto Lamp Control is set to ON, Manual Lamp Control is turned off automatically.

● Get Manual Lamp Status

Command Data Length

0x58 0

● Set Manual Lamp

Command Data Length Data 10x58 1 LampValue

LampValue : The Manual Lamp Value code for the TV / Monitor(0 ~ 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x58 LampValue

LampValue : Same as aboveNote : If Lamp Value returns to 0xFF ,it means Manual Lamp Control is in OFF mode

If Dynamic contrast is set to on, Auto Lamp Control is not work.

● Nak



62

49) Safety Screen Control

● FunctionThe Computer turns the Safety Screen Control of the TV/Monitor

● Get Safety Screen Status

Command Data Length

0x5B 0

● Set Safety Screen

Command Data Length Data 1 Data 2 Data 30x5B 1 Type Interval Second

Type : Scroll Type which will be set up into TV / Monitor (3 ~ 6)Interval : Scroll Interval which will be set up into TV / Monitor (0(off) ~ 10)Second : Scroll Time which will be set up into TV / Monitor (0(off) ~ 5)

Data 1 Type3 Scroll4 Pixel5 Bar6 Eraser

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 2 Val3 CheckSum0xFF 5 'A' 0x5B Type Interval Second

Type : Same as aboveInterval : Same as aboveSecond : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x5B ERR


63

50) Video Wall Mode Control

● FunctionThe Computer will switch the mode when the Video Wall feature of the TV / Monitor is set to OnAvailable only when the Video Wall is On.Not available in MagicNet

● Get Video Wall Mode

Command Data Length

0x5C 0

● Set Video Wall Mode

Command Data Length Data 10x5C 1 WallMode

WallMode : The Video Wall Mode code for the TV / Monitor.

1 Full0 Natural

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x5C WallMode

WallMode : Same as above

● Nak



64

51) Safety Lock

● FunctionThe Computer turns the Safety Lock of TV/Monitor On/Off.This can be operated regardless of the power On/Off

● Get Safety Lock Status

Command Data Length

0x5D 0

● Set Safety Lock Enable/Disable

Command Data Length Data 10x5D 1 Lock

Lock : The Lock code for the TV / Monitor

1 On0 Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x5D Lock

Lock : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x5D Lock


65

52) Panel Lock

● FunctionThe Computer turns the Panel function Key Lock of TV/Monitor On/Off.Available even when the power is turned OFF.

● Get Panel Lock Status

Command Data Length

0x5F 0

● Set Panel Lock Enable/Disable

Command Data Length Data 10x5F 1 Panel Lock

Lock : The Panel Key Lock On/Off code for the TV / Monitor

1 Lock0 Unlock

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x5F Panel Lock

Lock : Same as above

● Nak



66

53) OSD On/Off

● FunctionThe Computer turns the OSD of TV/Monitor On/Off.When the OSD is On, the OSD is displayed on the screen.When the OSD is Off, the OSD is not displayed on the screen.

● Get OSD Enable Status

Command Data Length

0x70 0

● Set OSD Enable/Disable

Command Data Length Data 10x70 1 OSD

OSD : The OSD On/Off code for the TV / Monitor

1 OSD Enable0 OSD Disable

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x70 OSD

OSD : Same as above

● Nak



67

54) P.Mode Control

● FunctionThe Computer changes the Picture Mode of TV/Monitor.

● Get PMode Status

Command Data Length

0x71 0

● Set PMode

Command Data Length Data 10x71 1 PMode

PMode : The Picture Mode code for the TV / Monitor

Source Data ModeAV

S-VideoComponent

HDMIATVDTV

0x00 Dynamic0x01 Standard0x02 Movie

0x03 Custom

PCBNCDVI

MagicNet

0x10 Entertain0x11 Internet0x12 Text0x13 Custom

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x71 PMode

PMode : Same as above

● Nak



68

55) S.Mode Control

● FunctionThe Computer changes the Sound Mode of TV/Monitor.

● Get SMode Status

Command Data Length

0x72 0

● Set SMode

Command Data Length Data 10x72 1 SMode

SMode : The Sound Mode code for the TV / Monitor

Data Mode0x00 Standard0x01 Music0x02 Movie0x03 Speech0x04 Custom

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x72 SMode

SMode : Same as above

● Nak



69

56) NR Mode Set (ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer changes the Digital NR Mode.

● Get NR Mode Status

Command Data Length

0x73 0

● Set NR Mode

Command Data Length Data 10x73 1 NR Mode

NR Mode : The NR Mode On/Off code for the TV / Monitor

1 NR Mode On0 NR Mode Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x73 NR Mode

NR Mode : Same as above

● Nak



70

57) PC Color Tone Control (PC, BNC , DVI, MagicNet only)

● FunctionThe Computer changes the Color tone of TV/Monitor.

● Get Color Tone Status

Command Data Length

0x75 0

● Set Color Tone

Command Data Length Data 10x75 1 Color Tone

Color Tone : The Color Tone Valur Code for the TV / Monitor(1 ~ 3)

Source Data Mode

PCDVIBNC

0x00 Custom0x01 Cool0x02 Normal0x03 Warm

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Check

Sum0xFF 3 'A' 0x75 Color Tone

Color Tone : Same as above

● Nak



71

58) Auto AutoAdjustment

● FunctionThe Computer adjusts the Auto Adjustment of TV/Monitor Enable/Disable.Auto Adjustment is only available when the power is turned On.

● Get A.Adjustment Status

Command Data Length

0x76 0

● Set A.Adjustment

Command Data Length Data 10x76 1 A.Adjustment

A.Adjustment : The Auto Adjustment Value Code for the TV / Monitor

1 Enable0 Disable

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x76 A.Adjustment

A.Adjustment : Same as above

● Nak



72

59) All Keys Lock

● FunctionThe Computer switches both the Remote Control and the Panel Key Lock function ON/PFF.Available even if the power is turned OFF.

● Get All Key Status

Command Data Length

0x77 0

● Set All Key Lock/Unlock

Command Data Length Data 10x77 1 All Key

All Key : The Key Lock On.Off Code for the TV / Monitor

1 Lock0 Unlock

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x77 All Key

All Key : Same as above

● Nak



73

60) SRS TSXT Control

● FunctionThe Computer enables ON/OFF of SRS TSXT for TV/Monitor.

● Get SRS TSXT Status

Command Data Length

0x78 0

● Set SRS TSXT

Command Data Length Data 10x78 1 SRS

SRS: SRS TSXT Code which will be set up into TV / Monitor

1 SRS On0 SRS Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x78 SRS

SRS : Same as above

● Nak



74

61) Film Mode Control

● FunctionThe Computer enables ON/OFF of Film Mode for TV/Monitor.

● Get Film Mode Status

Command Data Length

0x79 0

● Set Film Mode

Command Data Length Data 10x79 1 FMode

FMode : Film Mode Code which will be set up into TV / Monitor

1 Film Mode On0 Film Mode Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x79 FMode

FMode : Same as above

● Nak



75

62) Signal Balance (PC,BNC Only)

● FunctionThe Computer enables ON/OFF of Signal Balance for Monitor.

● Get Signal Balance Status

Command Data Length

0x7A 0

● Set Signal Balance

Command Data Length Data 10x7A 1 SBalance

SBalance : Signal Balance Code which will be set up into Monitor

1 Signal Balance On0 Signal Balance Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x7A SBalance

SBalance : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0x7A ERR


76

63) SB Gain (PC,BNC Only)

● FunctionThe Computer changes the Gain value of Signal Balance for Monitor.

● Get SBGain Status

Command Data Length

0x7E 0

● Set SBGain

Command Data Length Data 10x7E 1 SBGain

SBGain : Gain value which will be set up into Monitor.Code (0~ 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x7E SBGain

SBGain : Same as above

● Nak



77

64) SB Sharpness (PC,BNC Only)

● FunctionThe Computer changes the Sharpness value of Signal Balance for Monitor.

● Get SB Sharpness Status

Command Data Length

0x7F 0

● Set SB Sharpness

Command Data Length Data 10x7F 1 SBSharpness

SBSharpness : Sharpness value which will be set up into Monitor.Code (0~ 100)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x7F SBSharpness

SBSharpness : Same as above

● Nak



78

65) Panel On Time

● FunctionThe Computer show the Panel On Time status for Monitor.

● Get Panel On Time Status

Command Data Length

0x83 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 2 CheckSum0xFF 4 'A' 0x83 PTime_H PTime_L

PTime_H : Panel On Time HighPTime_L : Panel On Time Low

● Nak



79

66) Video Wall On

● FunctionThe Computer enables ON/OFF of Video Wall for Monitor.

● Get Video Wall Status

Command Data Length

0x84 0

● Set Video Wall

Command Data Length Data 10x84 1 V.Wall_On

V.Wall_On : Video Wall On Code which will be set up into Monitor

1 Video Wall On0 Video Wall Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x84 V.Wall_On

V.Wall_On : Same as above

● Nak



80

67) Temperature Control

● FunctionThe Computer set the Max temperature of TV/Monitor.

● Get Temperature Status

Command Data Length

0x85 0

● Set Temperature

Command Data Length Data 10x85 1 Temperature

Temperature : Temperature Code which will be set up into TV/Monitor

Data 46 ~ 125(℃)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x85 Temperature

Temperature : Same as above

● Nak



81

68) Brightness Sensor

● FunctionThe Computer enables ON/OFF of Brightness Sensor for TV/Monitor.

● Get Brightness Sensor ON/OFF Status

Command Data Length

0x86 0

● Set Brightness Sensor ON/OFF

Command Data Length Data 10x86 1 BR_Sensor

BR_Sensor : Brightness Sensor Code which will be set up into Monitor

1 Brightness Sensor On0 Brightness Sensor Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x86 BR_Sensor

BR_Sensor : Same as above

● Nak



82

69) Dynamic Contrast(ATV, DTV, AV, S-Video, Component, HDMI Only)

● FunctionThe Computer enables ON/OFF of Dynamic Contrast for TV/Monitor.

● Get Dynamic Contrast ON/OFF Status

Command Data Length

0x87 0

● Set Dynamic Contrast ON/OFF

Command Data Length Data 10x87 1 DY_Cont

DY_Cont : Dynamic Contrast Code which will be set up into Monitor

1 Dynamic Contrast On0 Dynamic Contrast Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x87 DY_Cont

DY_Cont : Same as above

● Nak



83

70) Safety Screen On

● FunctionAllows Safety Screen function for current TV/Monitor screen

● Get Safety screen StatusNone

● Set Safety screen

Command Data Length Data 10x88 1 Second

Second : Time to function Scroll for TV/Monitor. (Per Second 1 ~ 5)

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0x88 Second

Second : Same as above

● Nak



84

71) Video Wall Control

● FunctionThe Computer control the ON/OFF operation of the Video Wall feature for the TV / Monitor.Not available in MagicNet.

● Get Video Wall Status

Command Data Length

0x89 0

● Set Video Wall

Command Data Length Data 1 Data 20x89 2 Wall_Div Wall_SNo

Wall_Div : The Video Wall Divider code for the TV / Monitor

VH 1 2 3 4 5

OFF 0x00 0x00 0x00 0x00 0x001 0x11 0x12 0x13 0x14 0x152 0x21 0x22 0x23 0x24 0x253 0x31 0x32 0x33 0x34 0x354 0x41 0x42 0x43 0x44 0x455 0x51 0x52 0x53 0x54 0x55

Wall_SNo : The Video Wall Number code for the TV / Monitor

Set Number Data1 0x012 0x02... ...24 0x1825 0x19

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 2 CheckSum0xFF 4 'A' 0x89 Wall_Div Wall_SNo

Wall_Div : Same as aboveWall_SNo : Same as above

● Nak



85

72) Model Name Control

● FunctionThe Computer shows the Model Name information of the TV / Monitor

● Get Model Name Status

Command Data Length

0x8A 0

● Ack

Command Data Length Ack/Nak r-CMD Val 1 Val 2 Val_3 Val_4 Val_50xFF 0x12 'A' 0x8A M_Name1 M_Name2 M_Name3 M_Name4 M_Name5

Val 6 Val 7 Val_8 Val_9 Val_10 Val 11 Val_12 Val_13M_Name6 M_Name7 M_Name8 M_Name9 M_Name10 M_Name11 M_Name12 M_Name13

Val_14 Val_15 Val_16Check Sum

M_Name14 M_Name15 M_Name16

M_Name1 ~ M_Name16 : The Model Name code for the TV / Monitor

M_Name1 'S'M_Name2 'y'M_Name3 'n'M_Name4 'c'M_Name5 'M'M_Name6 'a'M_Name7 's'M_Name8 't'M_Name9 'e'M_Name10 'r'M_Name11 '4'M_Name12 '0'M_Name13 '0'M_Name14 'D'M_Name15 'X'M_Name16 'N'

86

73) MagicNet PIP (MagicNet Only)

● FunctionThe Computer turns the PIP function ON/OFF at MagicNet .

● Get MagicNet PIP statusNone

● Set MagicNet PIP On - (Data in Red font is for model 460Txn)

Command Data Length PIP ON Data 1 Data 2 Data 3 Data 4 Data 5

0xE0 0x0C(0x13) 0x01 H Position

High-ByteH PositionLow-Byte

V PositionHigh-Byte

V PositionLow-Byte

H SizeHigh-Byte

Data 6 Data 7 Data 8 Data 9 Data 10 Data 11 Data 11 Data 12 Data 13

H SizeLow-Byte

V SizeHigh-Byte

V SizeLow-Byte P.Source TV

Channel S.Select Country ATV/DTV AirCable

Data 14 Data 15 Data 16 Data 17 Data 18

CH_NUMHigh_Byte

CH_NUMLow_Byte Sel_Minor Minor_CH


H Position High-Byte : The Position value code for PIP H-Start High-Byte.H Position Low-Byte : The Position value code for PIP H-Start Low-Byte.V Position High-Byte : The Position value code for PIP V-Start High-Byte.V Position Low-Byte : The Position value code for PIP V-Start Low-Byte.H Size High-Byte : The Size value code for PIP H-width High-Byte.H Size Low-Byte : The Size value code for PIP H-width Low-Byte.V Size High-Byte : The Size value code for PIP V-width High-Byte.V Size Low-Byte : The Size value code for PIP V-width Low-Byte.Note : The PIP Start Position and Size do not over 1366 X 768 or 1920 X 1080P.Source : The Input source Code

0x14 PC0x1E BNC0x18 DVI0x0C AV0x04 S-Video0x08 Component0x21 HDMI0x30 TV0x40 DTV

TV Channel : Channel Number (0~99) Note : 460Txn OnlyS.Select : The Sound select Code

1 MagicNet Sound0 PIP Sound

87

Country : The value code for the country of the TV / Monitor (0 : Korea, 1: U.S.A, ...)ATV_DTV : The value code for the ATV/DTV of the TV / Monitor (0 : Analog TV, 1: Digital TV)AirCable : The value code for the Air/Cable of the TV / Monitor (0 : Air, 1: Cable)CH_NUM High_Byte : The value code for the Major Channel High-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)CH_NUM Low_Byte : The value code for the Major Channel Low-Byte of the TV / DTV

(Analog TV : 1 ~ 135, Digital TV : 0 ~ 999)Sel_Minor : The value code for the Minor Channel Enable/Disable of the TV / Monitor

(0 : Enable, 1 : Disable)(DTV Only)Minor_CH High_Byte : The value code for the Minor Channel High-Byte of the TV / Monitor

(0 ~ 999)(DTV Only)Minor_CH Low_Byte : The value code for the Minor Channel Low-Byte of the TV / Monitor

(0 ~ 999)(DTV Only)

● Ack(Data in Red font is for model 460Txn)

Command Data Length Ack/Nak r-CMD PIP ON Val 1 Val 2 Val 3 Val 4

0xFF 0x15 'A' 0xE0 0x01 H PositionLow-Byte

H PositionHigh-Byte

V PositionLow-Byte

V PositionHigh-Byte

Val 5 Val 6 Val 7 Val 8 Val 9 Val 10 Val 11 Val 12H Size

Low-ByteH Size

High-ByteV Size

Low-ByteV Size

High-Byte P.Source TVChannel S.Select Country

Val 13 Val 14 Val 15 Val 16 Val 17 Val 18 Val 19CheckSumATV_DTV AirCable CH_NUM

High_ByteCH_NUMLow_Byte Sel_Minor Minor_CH


H Position Low-Byte : Same as aboveH Position High-Byte : Same as aboveV Position Low-Byte : Same as aboveV Position High-Byte : Same as aboveH Size Low-Byte : Same as aboveH Size High-Byte : Same as aboveV Size Low-Byte : Same as aboveV Size High-Byte : Same as aboveP.Source : Same as aboveTV Channel : Same as aboveS.Select : Same as aboveCountry : Same as aboveATV_DTV : Same as aboveCH_NUM High_Byte : Same as aboveCH_NUM Low_Byte : Same as aboveSel_Minor : Same as aboveMinor_CH High_Byte : Same as aboveMinor_CH Low_Byte : Same as above

88

● Set MagicNet PIP Off (Data in Red font is for model 460Txn)

Command Data Length PIP Off

0xE0 0x0C0x13 0x00

● Ack (Data in Red font is for model 460Txn)

Command Data Length Ack/Nak r-CMD PIP Off

0xFF 0x0E0x15 'A' 0xE0 0x00

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0xE0 ERR


89

74) Panel ON/OFF

● FunctionThe Computer control ON/OFF status of Panel for TV/Monitor.

● Get Panel ON/OFF Status

Command Data Length

0xF9 0

● Set Panel ON/OFF

Command Data Length Data 10xF9 1 Panel

Panel : Panel On/Off Code which will be set up into Monitor

0 Panel On1 Panel Off

● Ack

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'A' 0xF9 Panel

Panel : Same as above

● Nak

Command Data Length Ack/Nak r-CMD Val 1 CheckSum0xFF 3 'N' 0xF9 ERR


Date post:	27-Aug-2018
Category:	Documents
Upload:	nguyenthuy
View:	218 times
Download:	0 times

Multiple Display Control Protocol - samsung.com · 6 1. Overview This document provides...

Documents