+ All Categories
Home > Documents > Nature2 Quick-Start Guide - WordPress.com · Nature2 Quick-Start Guide 1. Start with a clean tub,...

Nature2 Quick-Start Guide - WordPress.com · Nature2 Quick-Start Guide 1. Start with a clean tub,...

Date post: 20-Aug-2020
Category:
Upload: others
View: 5 times
Download: 0 times
Share this document with a friend
1
Nature2 Quick-Start Guide 1. Start with a clean tub, and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer.) 2. Fill spa with fresh water and operate circulating pump. 3. Test water with MPS 3-Way Test Strips and Hardness Test Strips; adjust where necessary. 4. Add Natural Clarifier at the rate of 1 oz./500 gallons, weekly. 5. Add Metal Free stain/metal preventer per label instructions. 6. Shock water at initial fill and weekly with Oxy-Spa non-chlorine MPS shock at the rate of 1 ½ - 2 oz. per 500 gallons. (1 ½ tablespoons = approx. 2 oz.). Nature2 is not compatible with bromine. 7. Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest with test strips; readjust water balance if necessary. 8. Remove Nature2 from package and connect the support stem(s). 9. Shut spa off and remove filter. Slide device into filter cartridge core per examples provided; reinstall filter. Once installed, Nature2 cartridge must be at least 1” above the bottom of the filter to assure proper water flow and prevent blockage. 10. Place and keep ZorbO in spa to absorb oil scum, replace every 3 - 6 months. Recommended Chemical Levels Test with MPS 3-Way Test Strips pH: 7.2 - 7.6 Total Alkalinity: 80 - 120 ppm Calcium Hardness: 150 - 300 ppm Test with Hardness Test Strips START-UP PROCESS: TEST WATER WEEKLY. WAIT 5 - 10 MINUTES WHEN ADDING DIFFERENT CHEMICALS! Adding too many chemicals at once can create cloudy water. (800) 823-3638 Mon-Fri 6 AM - 5 PM PST NOTE: Follow instructions on each bottle according to your spa’s capacity guidelines. 1. Clean Tub & New or Clean Filter(s) 2. Fill Spa & Circulate Water Total Hardness 3. MPS 3-in1 Test Strips Test water 4. Add Natural Clarifier 5. Add Metal Free Shock Water with Oxy-Spa 6. 8. Connect support stems to Nature2 9. Add Nature2 to filter. Replace in spa. 7. Circulate water for 1 - 2 hours and retest MPS 3-in1 Test Strips Total Hardness 10. Place ZorbO in Spa Nature2 N2 N2 N2 N2 N2 Stand Pipe Open Center - CORRECT install Open Center - WRONG install Open Center - with Stand Pipe Closed Top - Correct Install Nature2 Filter Style Installations
Transcript
Page 1: Nature2 Quick-Start Guide - WordPress.com · Nature2 Quick-Start Guide 1. Start with a clean tub, and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from

Nature2 Quick-Start Guide

1. Start with a clean tub, and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer.)

2. Fill spa with fresh water and operate circulating pump.

3. Test water with MPS 3-Way Test Strips and Hardness Test Strips; adjust where necessary.

4. Add Natural Clarifier at the rate of 1 oz./500 gallons, weekly.

5. Add Metal Free stain/metal preventer per label instructions.

6. Shock water at initial fill and weekly with Oxy-Spa non-chlorine MPS shock at the rate of 1 ½ - 2 oz. per 500 gallons. (1 ½ tablespoons = approx. 2 oz.). Nature2 is not compatible with bromine.

7. Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest with test strips; readjust water balance if necessary.

8. Remove Nature2 from package and connect the support stem(s).

9. Shut spa off and remove filter. Slide device into filter cartridge core per examples provided; reinstall filter. Once installed, Nature2 cartridge must be at least 1” above the bottom of the filter to assure proper water flow and prevent blockage.

10. Place and keep ZorbO in spa to absorb oil scum, replace every 3 - 6 months.

Recommended Chemical Levels

Test with MPS 3-Way Test Strips

pH: 7.2 - 7.6Total Alkalinity: 80 - 120 ppm Calcium Hardness: 150 - 300 ppm

Test with Hardness Test Strips

START-UP PROCESS:

TEST WATER WEEKLY.

WAIT 5 - 10 MINUTES WHEN ADDING DIFFERENT CHEMICALS! Adding too many chemicals at once can create cloudy water.

(800) 823-3638Mon-Fri 6 AM - 5 PM PST

NOTE: Follow instructions on each bottle according to your spa’s capacity guidelines.

1.

Clean Tub & New or Clean Filter(s)

2.

Fill Spa & Circulate Water

Total Hardness

3.

pH

MONOPERSULFATE (MPS)

TOTAL ALKALNITY

MPS3-in1

Test Strips

Test water

4.

Add Natural Clarifier

5.

Add Metal Free

Shock Water with Oxy-Spa

6. 8.

Connect support stems to Nature2

9.

Add Nature2 to filter. Replace in spa.

7.

Circulate water for 1 - 2 hours and retest

pH

MONOPERSULFATE (MPS)

TOTAL ALKALNITY

MPS3-in1

Test Strips

Total Hardness

10.

Place ZorbO in Spa

Nature2

N2

N2

N2 N2

StandPipe

N2

N2

N2 N2

StandPipe

Open Center - CORRECT install

Open Center - WRONG install

Open Center - with Stand Pipe

Closed Top - Correct Install

Nature2 Filter Style Installations

Recommended