Date post: | 06-Apr-2018 |
Category: |
Documents |
Upload: | aneeta-hari |
View: | 219 times |
Download: | 0 times |
of 42
8/3/2019 Newton Waterproofing Systems
1/42
NEWTON WATERPROOFING SYSTEMS
Product Catalogue
100 - Cementitious Products
200 - Deck And Roong300 - Waterproong of Concrete Structures
400 - External Waterproong
500 - Cavity Drain Waterproong
600 - Flooring Membranes
700 - Liquid Applied Floor Coatings
800 - Damp Proong
900 - Liquid Primers & Sealers
FlexProof Construction Joint Waterproong
Diathonite Insulating Plaster
Sump and Pump
Multi-Use
John Newton & Co. Ltd.
Issue Date: February 2012
Ln6 (L34)Cl/SfB
Protecting buildings, since 1848
8/3/2019 Newton Waterproofing Systems
2/42
PRODUCT CATALOGUE
SYSTEM 100 - CEMENTITIOUS PRODUCTS
Newton System 100 is a comprehensive portfolio
of cementitious products which have been
introduced into our structural waterproong range
to complement and complete our basement
waterproong designs in areas where the Newton
System 500 would not be suitable. Such details
include - lift shafts, at softs and externally to
retained slabs and ring beams.
Newton 101 F (CW 101), Page 4
Cementitious Flexible Waterproong Membrane
Newton 102 WaterPlug (CW 102), Page 5
Fast Setting Polymer Compound To Seal Leaks
Newton 103 SBR (CW 103), Page 5
Waterproof Additive
Newton 106 Lime Inhibitor (LC1), Page 5
Lime Inhibitor for Application to Concrete Surfaces
Newton 107 QuickFillet (CW 107), Page 6
Fast Setting Pre-Mix Mortar for Angle Fillets
SYSTEM 200 - DECK & ROOFING
A complete range of externally applied elastomeric
high performance liquid membranes and ancillaries
for balconies, terraces, at and inverted roofs,
podium decks, car parks and reservoirs. This new
portfolio of seamless and robust liquid membranes
gives speciers and specialist waterproong
contractors a quick and cost effective solution to
protect external areas from water ingress.
Newton RubberFlex System, Page 7
Podium Deck and Flat Roof Waterproong System
Newton 204 Thinner (RF 204), Page 8
Polyurethane Thinning & Cleaning Agent
Newton 205 ColorSeal (LM 205), Page 8
UV Colour Stable Polyurethane Coating
Newton 207 DeckDrain (M30), Page 9
Drainage Membrane for Decks and Flat Roofs
Newton 209 Root Barrier (M32), Page 9
Puncture Resistant Root Barrier Membrane
Newton 210 FlexProof-NV (FP4), Page 10
Waterproong of Podium Decks and Flat Roofs
Newton 220 Reservoir (M31), Page 10
Extensive Green Roof Drainage Membrane
SYSTEM 300 - WATERPROOFING OF
CONCRETE STRUCTURES
Newton System 300 is a range of products, some
unique to John Newton, used to waterproof con-
struction joints and movement joints of retained
concrete structures so that they become integrally
waterproof without the need of additional water-
proong products, dened within BS8102:2009 as
Type B waterproong.
Newton 301 AquaProof, Page 11
Metal Construction Joint Water Bar
Newton 302 InjectionHose, Page 11
Maintainable Injection Water Bar System
Newton 303 PolyProof, Page 12
High Grade Hydrophilic Water Bar
Newton 304 PolyProof Inject, Page 12
High Grade Hydrophilic Water Bar
Newton 305 ActiveJoint, Page 12
Physical Movement Joint Water Bar
Newton 306 SwellMastic, Page 13
Swelling Adhesive
Newton 307 PipeSeal, Page 13
Pipe Collar
Newton 308 Stopaq (SX 108), Page 13
Unique Hydrophilic Polymer Sealant
SYSTEM 400 - EXTERNAL WATERPROOFING
System 400 is a range of products for the
waterproong of the outside of earth retainedstructures. Products include sheet membranes for
the complete envelopment of the raft and walls,
exible liquid products for the waterproong of
retained walls and composite drainage membranes
for preventing the build up of ground water to the
walls or below the raft. Newton System 400 products
can provide Type A and Type B waterproong to
Grades 2 & 3 as dened within BS8102:2009
Newton 401 FlexProof-X1, Page 14
Flexible Membrane for Retaining Walls
Newton 402 Aquabit, Page 15
Flexible Membrane for Retaining Walls
Newton 403 HydroBond, Page 15
Hydrophilic and Bonding Membrane for Raft and
Wall Waterproong
Newton 410 Geodrain, Page 16
Externally Applied Drainage Membrane
Note: Please check individual product sheets for advice on appropriate xings and ancillary products. Contact our Technical
Department for further information on 020 7237 1217. Copies of our BBA Certicates, Brochures and Data Sheets can be
downloaded from www.newton-membranes.co.uk. Products and their specications can be changed or modied without
prior notice. All copy, diagrams, images and Newton trade names/logos and designs used in this catalogue remain theintellectual property of John Newton and Company Ltd. and may not be reproduced without the written permission of the
Directors of John Newton and Company Ltd. Any party who exploits this property may be subject to prosecution.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
8/3/2019 Newton Waterproofing Systems
3/42
PRODUCT CATALOGUE
SYSTEM 500 - CAVITY DRAIN WATERPROOFING
The professionals waterproong system of
choice, Newton System 500 is an internally
applied waterproong system based upon our range
of cavity drain membranes, drainage conduits and
sophisticated pumping and control systems. Unlike
conventional tanking, Newton System 500 is not
attempting the almost impossible and trying to
hold water back, but places designed maintainable
depressurisation voids at known weaknesses in
the structure so that ingressing water is simply
captured and diverted out of the property.
Wall Membranes
Newton 503 (M5), Page 17
Newton 503 Mesh (M11 & M12), Page 17
Newton 508 (M1 & M2), Page 18
Newton 508 Mesh (M3), Page 18
Newton 520 (M4 & M13), Page 18
Drainage System
Newton Basedrain (D1), Page 18
SYSTEM 600 - FLOORING MEMBRANES
Newton System 600 is a range of HDPE and
HDPP ooring membranes offering a complete
damp proof solution for both commercial and
domestic ooring applications. As well as
providing protection from dampness within the
oor, our membranes de-couple the oor nish
from the substrate preventing damage due tosubstrate movement and cracking. Newton damp
proof membranes can be installed over existing
and green concrete. In addition, our ooring
membranes are a popular solution for dealing with
inherent hydrocarbons or ground gas problems.
Newton ooring membranes can accommodate a
variety of nishes including timber oors, screeds
and direct tiles.
Flooring Membranes
Newton 601 Slimline (M6), Page 19
Newton 603 (M23), Page 19
Newton 603 Mesh (M24 & M25), Page 20
SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS
System 700 is a range of liquid applied protective
and decorative internal ooring products. These
products are fast curing and available in a
variety of colours, and are typically used for the
refurbishment and protection of commercial and
domestic oors.
Newton 701 HB (LM 701), Page 21
High Build Epoxy Floor Coating
Newton 702 EcoSeal (LM 702), Page 21
Highly Resistant Polyurethane Floor Coating
SYSTEM 800 - DAMP PROOFING
Newton System 800 is a range of BBA approved
damp proof membranes and ancillaries which are
quick and clean to install and offer a permanent
solution for damp proong walls. The meshed
membranes provide a rm key and impermeable
barrier on any damp or deteriorating surface ready
for plaster, render or dot & dab plasterboard. The
un-meshed Newton 803 is used where insulation
requirements dictate the use of a timber or steel
frame ready for plasterboard. Quick, clean and
proven to work, Newton damp proof membranes
offer a permanent and cost effective damp
proong solution.
Damp Proong Membranes
Newton 805 Newlath (M9 & M10), Page 22
Newton 803 (M19 & M20), Page 23
Newton 803 Newtonite (M16, M21, M22), Page 23Newton 801 FlexProof-X1 Wet Room Waterproong,
Page 23
Damp Proong Ancillaries
Newton 800 Mesh Plug (A16), Page 24
Newton MultiPlug (A1), Page 24
Newton 800 Cob Plug (A17), Page 24
Newton 800 Newtonite Plugs (A20), Page 24
Newton 800 Mastic (A18), Page 25
Newton Mesh Tape (A25), Page 25
Newton Overtape (A8), Page 25
Newton 800 Prole (A19), Page 25
SYSTEM 900 - LIQUID PRIMERS & SEALERS
Newtons high performance range of liquid applied
products are used in conjunction with System 200
and 700 liquid membranes. They act as priming
agents for a variety of substrates prior to the
application of our specialist waterproong and
ooring membranes.
Newton 901 Humidity Primer (PS 901), Page 26
Epoxy Primer Suitable for High Humidity SubstrateNewton 902 (PS 902), Page 26
Liquid Applied Radon, Gas & Vapour Barrier
Newton 903 PU Primer (PS 903), Page 27
Epoxy Primer for Nonporous Substrate
Newton 904 HP Accelerant (PS 904), Page 27
Humidity Primer Accelerant
Newton 906 Mould Stop (PS 906), Page 27
Mould Steriliser & Killer
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
8/3/2019 Newton Waterproofing Systems
4/42
PRODUCT CATALOGUE
NEWTON FLEXPROOF - CONSTRUCTIONJOINT WATERPROOFING
Newton FlexProof-X1 forms an elastomeric polymer
membrane that is rainproof in minutes and
capable of handling severe building movements
and deformations. FlexProof-X1 is quite unique
with amazing characteristics allowing it to be used
without a primer, without mixing and in weather
conditions that preclude the use of alternatives.
Newton FlexProof-X1 (FP1), Page 28
Construction Joint Waterproong
NEWTON DIATHONITE - INSULATING PLASTER
Newton Diathonite is a premixed plaster, bre-
reinforced with cork (granular 0-3 mm), clay
powders and NHL 3.5 natural hydraulic lime.
The resulting natural compound produces a plaster
with unrivalled thermal and acoustic properties that
is both hard wearing and exible which is ideal for
both internal and external applications. .
Newton Diathonite, Page 29
Eco Thermal Plaster with Insulation and Acoustic
Properties
SUMP AND PUMP
Newtons have an extensive range of submersible
pumps and pumping ancillaries. We supply the
highest quality pumps available in each class,
for the control of clean ground water, grey water,
efuent or sewage.
Clean/Ground Water Pumps
Newton NP150 (P1), Page 30
Newton CP250 (P31), Page 30
Newton CP400 (P32), Page 31
Newton NP400 (P2 & P3), Page 31
Newton NP400PP (P13), Page 31
Newton NP400LLPS (SP1), Page 31
Newton CP750 (P33), Page 32
Newton NP750 (P5 & P6), Page 32
Efuent Pumps (Not Sewage)
Newton NP400W (P4), Page 32
Sewage Pumps
Newton SP750 Ranger (P9), Page 33
Newton Flygt DXG (Grinder) (P14 & P16) Page 33
Sewage Lifting Station
Trojan Sewage Pumping System (TR1-TR12), Page 33
Clean/Ground/Efuent Pumping Systems
Titan-Pro White (TPW), Page 34
Titan-Pro Green (TPG), Page 34
Newton Titan-2 (T1-T10), Page 34
Pumping Ancillary Products
Newton Control Panel Pro (CP2), Page 35
Newton High Water Level Alarm (PA50), Page 35
Newton Dialer (PA5, PA6, PA7), Page 35
Newton 1200w Power Converter (C1 & C3), Page 36
Newton 3000w Power Converter (C2 & C4), Page 36
Newtons can also provide a wide range of specialist
submersible pumps and sump chambers which
can be tailor made for site-specic conditions. For
further information call our technical department
on 020 7237 1217
MULTI-USEThe Multi-Use section is home to products that
are used within more than one of our systems.
WaterSeal Tape, for example, can be used with
System 300, System 400, System 500, System 600
and System 800.
Newton Mesh Tape (A25), Page 37
Newton Overtape (A7, A8, A9), Page 37
Newton WaterSeal Rope (A6 & A6W), Page 37
Newton WaterSeal Tape (A5 & A5W), Page 38
Newton MultiPlug (A1), Page 38
Newton NuSeal Plugs (A2 & A3), Page 38
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
8/3/2019 Newton Waterproofing Systems
5/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 100Cementitious Products
SYSTEM OVERVIEW
NEWTON SYSTEM 100 - CEMENTITIOUS PRODUCTSSystem Overview
Newton System 100 is a comprehensive portfolio ofType A
(BS8102:2009) cementitious waterproong products for the sealing of
leaks and the waterproong of lift shafts, at softs, walls and slabs.
System 100 products can be used on their own, or in conjunction with
System 200, System 300, System 400 and System 500 waterproong
products, and with System 700 (Liquid Flooring Membrane) and System
800 (damp-proong) products also.
NEWTON 101F (CW 101)Cementitious Flexible Waterproong Membrane
Newton 101F is a two-component acrylic modied cementitious coating.
It is the ideal product to waterproof and re-surface concrete and masonry.
101F is a hard wearing, seamless waterproong solution which is very
user friendly with simple on-site mixing methods.
Newton 101F is applied in two coats 1mm each to provide a total
thickness of 2mm. Each 1mm coat requires a coverage rate of
1.8kg per m to give a total coverage rate of 3.6kg per m. Newton 101F
is supplied in two components of 1 x 25kg tub of powder and 10kg of
liquid additive (35kg pack) which will cover 9m - 10m
Typical Applications:
Waterproof lining for lift pits, swimming pools etc
Bathroom and wet areas
Waterproof coating for roofs
Internal application to at concrete softs in conjunction with
Newton System 500
Slurry application to form waterproof bunds
Lining existing concrete sump chambers
Protection of steels against carbonation and chloride attacks
Page 4
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
8/3/2019 Newton Waterproofing Systems
6/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 100Cementitious Products
SYSTEM OVERVIEW
NEWTON 102 WATERPLUG (CW 102)Fast Setting Polymer Compound To Seal Leaks
Newton 102 WaterPlug is a fast setting, polymer compound that instantly
stops running water or seepage through masonry or concrete substrates.
It becomes harder and more resistant when subjected to constant water
pressure. Newton 102 WaterPlug is a non-shrink material that expands
slightly and sets in approximate 2 minutes. Available in 5kg, 10kg or
25kg tubs.
Typical Applications:
Leak sealing prior to tanking with Newton 101F
Sealing of leaks at wall/oor junctions
Sealing of leaking mortar joints
Leak sealing of cracks in masonry or concrete
Repair of construction faults such as honeycombing
Anchoring of bolts or posts
Controlling water ingress during sump installations
NEWTON 103 SBR (CW 103)Waterproo Additive
Newton 103 SBR is a high quality liquid, water-based high solids
styrene butadiene polymer latex with high bonding and waterproong
characteristics. It is stable under wet alkaline conditions forming a
reinforcing polymer matrix within cementitious mixes. Available in 5kg,10kg and 25kg
Typical Applications:
Surface waterproong Lift shafts
Waterproof screeds Wall/oor junction llets
NEWTON 106 LIME INHIBITOR (LC1)Lime Inhibitor For Application To Concrete Suraces
Newton 106 Lime Inhibitor is applied to concrete surfaces prior to the
installation of a Newton System 500 cavity drain membrane waterproongsystem to prevent the leaching of free lime from the concrete. Primarily
designed to be used to new concrete structures, Newton Lime Inhibitor
should also be used to treat the following areas: newly formed concrete
walls, kickers and underpins, treatment to cut recesses prior to Basedrain
installation and as a concrete additive to newly formed sump chambers.
Supplied in 1kg units - Newton 106 is a concentrated mix to be added
1 part Newton 106 Lime Inhibitor to 9 parts clean water. Newton 106
should be applied in this 10 litre mix through a course sprayer and will
cover a maximum of 100 sq m
Product Features:
Solvent and caustic free Easy to use and handle
Non-hazardous (on dilution) Long term durability
Compatible with alkaline substrates
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 5
8/3/2019 Newton Waterproofing Systems
7/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 100Cementitious Products
SYSTEM OVERVIEW
NEWTON 107 QUICKFILLET (CW 107)Fast Setting Pre-Mix Mortar For Angle Fillets
Newton 107 QuickFillet is a fast setting and fast curing mortar with a
rapid strength gain used to quickly form 45 angled llets at junctions
between walls and oors or softs. Newton 107 QuickFillet should be
used to form llets for use with Newton 101F cementitious slurry and
can be used to reinforce internal corners ready for Newton liquid applied
membranes such as 201 RubberFlex, 205 ColorSeal or 702 EcoSeal.
Newton 107 Quick Fillet can also be used to repair substrate prior to the
use of Newton System 900 primers.
Newton 107 QuickFillet is supplied in 25kg tubs and when correctly mixedwith 3.6 litres of clean water should cover approx 30 linear metres applied
in a 25mm x 25mm llet
Typical Applications:
Creation of angle llets
Surface repairs to substrate prior to application of Newton System
900 oor primers
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 6
8/3/2019 Newton Waterproofing Systems
8/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 200Deck & Roofing
SYSTEM OVERVIEW
NEWTON SYSTEM 200 - DECK AND ROOFINGSystem Overview
Newton System 200 is a complete range of externally applied liquid
elastomeric membranes for the structural waterproong of podium decks,
balconies and terraces, at and inverted roofs, car parks, swimming
pools, green or turf roofs and reservoirs. This new portfolio of seamless
and robust liquid membranes gives speciers and specialist waterproong
contractors a quick and cost effective solution to protect external areas
from water ingress.
NEWTON RUBBERFLEX SYSTEMPodium Deck and Flat Roo Waterproong System
Newton RubberFlex is a BBA Certied single part liquid waterproong
material, which forms an elastomeric polyurethane membrane, resisting
UV rays and capable of handling severe building movements and
deformations. Newton RubberFlex is guaranteed against deterioration
for 25 years and is supported by BBA Certication Certicate Number
11/4840. Newton RubberFlex can be specied as a UV stable
waterproong membrane with high resistance to impact and abrasion
or can be the primary waterproong barrier when used with Newton
207 DeckDrain drainage membrane to create a complete drained
waterproong solution.
Newton RubberFlex is available in three variants, the choice of whichwould be dependent on the required speed of application between coats
as well as on the temperature and humidity at the time of installation and
the type and height of up-stand to be installed.
Newton 201 RubberFlex
Self levelling with standard cure times used for horizontal surfaces and
up-stands of up to 250mm with reinforcement.
Newton 202 RubberFlex-QC
Quick Curing derivative with fast cure times used for horizontal surfaces
and up-stands of up to 250mm with reinforcement.
Newton 203 RubberFlex-VThixotropic variant for larger vertical areas.
Newton RubberFlex can be applied either as a reinforced or a non-
reinforced system depending on substrate type or substrate quality. See
product datasheet for more details.
Application rates: 25kg is sufcient to cover 12.5m2 of surface with a two
coat treatment of 2kgs per m2 providing an overall membrane thickness
of 1.9mm (refer to data sheets for suggested drying times between coats)
Specialist application equipment such as spiked rollers are available
on request.
201 RubberFlex and 202 RubberFlex QC are available in 10kg and 25kg
tins. 203 RubberFlex-V is available in 10kg tins.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 7
8/3/2019 Newton Waterproofing Systems
9/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 200Deck & Roofing
SYSTEM OVERVIEW
NEWTON 204 THINNER (RF 204)Polyurethane Thinning & Cleaning Agent
Newton 204 Thinner is a slow acting blended solvent for use with Newton
RubberFlex and Newton 205 ColorSeal. Newton 204 Thinner is used to
dilute the polyurethane membrane and is especially useful when Newton
RubberFlex is applied by airless spray.
Newton 204 Thinner is also used as a cleaning medium for tools and
equipment used during the application of the membrane and it can
also be used as a barrier against humidity when having to store product
already opened. Newton 204 Thinner is supplied in 4kg, 9kg and 20kg
containers.
Newton 204 Thinner is also used for cleaning tools used with Newton
Flexproof products.
Typical Applications:
Cleaning of tools and equipment
Increasing viscosity of membranes for application by airless spraying
Sealing of product against moisture in opened containers
NEWTON 205 COLORSEAL (LM 205)UV Colour Stable Polyurethane Coating
Newton 205 ColorSeal is a UV stable, single component, protective
polyurethane resin top-coat. 205 ColorSeal provides a transparent hard
wearing coating, or it can be coloured with the addition of pigmented quartz
sand to provide a textured, slip resistant, UV colour stable nish. Its primary
use is as a UV stable and hard wearing protection coat above the Newton
RubberFlex podium deck and at roof waterproong system.
The exceptional strength and durability means that Newton 205 ColorSeal
can also be used as a stand-alone ooring product. It cures to a gloss
nish. For pedestrian walkways it is recommended that a coloured quartz
sand is applied to the still tacky rst coat of 205 ColorSeal to give a non-
slip surface. Newton 205 ColorSeal is supplied in 4kg, 9kg and 20kg
containers.
Coverage: a 4kg pack is sufcient to cover a prepared surface area of 13m2
with the recommended covering of 0.3kg/m2 providing an overall thickness
of 250-400 microns. With a two coat application which includes the quartz
sand anti-slip layer, coverage will be 6m2 with the recommended two
coat treatment
Typical Applications:
Heavy trafc areas
Industrial factories, depots and warehouses
UV colour stable and non-slip nish to other oor coatings
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 8
8/3/2019 Newton Waterproofing Systems
10/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 200Deck & Roofing
SYSTEM OVERVIEW
NEWTON 207 DECKDRAIN (M30)Drainage Membrane or Decks and Flat Roos
Newton 207 DeckDrain is a double cuspated, deck and at roof drainage
membrane, that incorporates a non-woven geotextile lter layer, bonded to
a water impermeable HDPE (High Density Polyethylene) core. The double
cuspated design provides two layers of drainage; allowing for primary
drainage through the geotextile lter, as well as secondary drainage between
the underside of 207 DeckDrain and the primary waterproong layer.
The lower drainage layer eliminates the risk of trapped water, a problem
associated with conventional single cuspated deck drainage membranes.
Newton 207 DeckDrain is supplied in 1.1m wide x 25m long rolls and is
simply laid above the waterproong membrane with the geotextile eece
uppermost.
Typical Applications:
As the drainage layer above a deck, balcony or at roof waterproong
membrane such as Newton 201 RubberFlex, particularly where:
1. Block paviours or ooring slabs are bedded on sand as the surface nish.
2. Soil lled planters are included to the deck or at roof.
Also suitable for use as a vertical drainage layer when used as part of
a professionally designed and installed externally applied basement
waterproong system.
NEWTON 209 ROOT BARRIER (M32)Puncture Resistant Root Barrier Membrane
Newton 209 RootBarrier is designed to eliminate root penetration. It
consists of an impermeable High Density Polyethylene (HDPE) membrane,
providing robust root-proof protection to the primary waterproong
membrane to green roofs or planters where intrusive root systems are
present.
The membrane has high tensile strength and puncture resistance
and provides an efcient, reliable and cost effective barrier to provide
protection against Japanese Knotweed and other aggressive root systems.
Typical Applications:
As a root barrier to protect the waterproong membrane from root damage
within intrusive green roof systems or planters.
Newton 209 RootBarrier is supplied in 1.2m wide x 50m long rolls and is
placed above the waterproong membrane and the Newton 207 DeckDrain
(if included in the design). Joints are overlapped by at least 150mm and
sealed with two lines of Newton Waterseal Tape.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 9
8/3/2019 Newton Waterproofing Systems
11/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 200Deck & Roofing
SYSTEM OVERVIEW
NEWTON 210 FLEXPROOF-NV (FP4)Waterproong o Podium Decks and Flat Roos
Newton 210 FlexProof-NV is a highly advanced single component liquid
waterproong material, which forms an elastomeric polymer membrane
capable of handling severe building movements and deformations.
Movement joints to Decks and Flat Roofs can also be waterproofed with
Newton 201 FlexProof-NV whether the main waterproong membrane is
FlexProof-NV or Newton RubberFlex.
Newton 210 FlexProof-NV has characteristics that allow it to be used
without a primer, without mixing and in weather conditions that preclude
the use of alternatives. With a tight project timescale, 210 FlexProof-NV
can be relied upon to ensure the project is completed on time.
Newton 210 FlexProof-NV can be used as the primary waterproong
membrane below a number of hard nishes and drainage options and
when partnered with Newton 207 DeckDrain drainage membrane, creates
a complete drained waterproong solution to your deck, terrace or at roof.
Newton 210 FlexProof-NV is supplied in 7.5kg and 26kg containers and is
applied to the deck or roof with a squeegee or trowel and is simply poured
into movement joints.
Typical Applications:
Waterproong of podium decks, balconies, terraces and at roofs.
As the primary waterproong membrane below a green roof.
As the waterproong membrane within a warm roof specication.
Waterproong of planters
NEWTON 220 RESERVOIR (M31)Extensive Green Roo Drainage Membrane
Newton 220 Reservoir is a unique drainage and water retention
membrane for use where a water reservoir is required for extensive green
roofs of sedum, herbaceous plants, mosses or grass above decks and
roofs.
Unlike other products of this type, Newton 220 Reservoir has a bonded
geotextile that prevents intrusion of the soil into the water holding cupsduring back-ll and compression. This results in a permanently larger
volume reservoir than any other 20mm deep green roof membrane.
When the water holding cups are full, the large drainage holes within the
HDPE core allow water to easily pass through to the drainage layer below
to prevent saturation and water logging of the green roof above.
Typical Applications:
As a water holding and drainage layer above a deck, at roof or pitched
roof where shallow planting is used to create an extensive green roof.
Newton 220 Reservoir is supplied in 0.92m wide x 50m long rolls and is simply
laid above the waterproong membrane with the geotextile eece uppermost.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 10
8/3/2019 Newton Waterproofing Systems
12/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 300Waterproofing of Concrete Structures
SYSTEM OVERVIEW
NEWTON SYSTEM 300
WATERPROOFING OF CONCRETE STRUCTURESSystem Overview
Newton System 300 is a range of products, some unique to John Newton,
used to waterproof construction joints and movement joints of retained
concrete structures so that they become integrally waterproof without the
need of additional waterproong products, dened within BS8102:2009
as Type B waterproofng.
Waterproong can be further enhanced by the addition ofType A (Newton
System 100 or System 400) or Type C(Newton System 500) waterproong
systems to provide a combined waterproong approach, recommended
by BS8102:2009 when absolute waterproong security is required.
The podium deck of a retained concrete structure would also require
waterproong with one of our System 200 products.
NEWTON 301 AQUAPROOFMetal Construction Joint Water Bar
Newton 301 AquaProof is a coated metal water bar system used for the
sealing of construction joints within retained concrete structures.
Newton 301 AquaProof features an adhesive, reactive
polymer coating on one of its sides. The coating creates a permanent
watertight seal with the surrounding concrete to create a water bar that
works immediately.
Newton 301 AquaProof is supplied in 6m rolls and is tted to the
reinforcing steel with Omega Clips prior to the placing of the concrete.
Typical Applications:
The waterproong of construction joints to poured concrete elements
of earth retained structures.
NEWTON 302 INJECTIONHOSE
Maintainable Injection Water Bar System
Newton 302 InjectionHose is a high performance injectable water bar
system used for the sealing of construction joints within retained concrete
structures.
The system offers many benets over conventional water bars,
especially its ability to grout poorly compacted concrete and by offering a
maintainable solution that allows for resealing of the construction joint,
post construction.
Newton 302 InjectionHose is supplied in reels of 120m and is applied to
an already formed concrete element prior to formation of the joint.
Typical Applications:
Post construction grouting and leak sealing of construction joints to
poured concrete earth retained structures.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 11
8/3/2019 Newton Waterproofing Systems
13/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 300Waterproofing of Concrete Structures
SYSTEM OVERVIEW
NEWTON 303 POLYPROOFHigh Grade Hydrophilic Water Bar
Newton 303 PolyProof is a very high grade hydrophilic water bar which
seals gaps in construction joints by swelling up to 400% its original size.
The water bar is adhered to the face of the rst pour of the joint with
either Newton 306 SwellMastic or Newton 309 Contact Adhesive. Can
also be used as the water bar in settlement or compression joints.
303 PolyProof is available in the following sizes:
Depth Width Length
303 PolyProof-2 2mm 20mm 25m
303 PolyProof-10 10mm 20mm 10m
303 PolyProof-30 30mm 30mm 5m
Typical Applications:
Waterproong of static construction joints, settlement joints and
compression joints to concrete earth retained structures.
NEWTON 304 POLYPROOF INJECTHigh Grade Hydrophilic Water Bar
Unique construction joint water bar that combines the high performance
swelling capabilities of Newton 303 PolyProof and the post construction
injection of grouts and resins provided by Newton 302 InjectionHose.
Newton 304 PolyProof Inject is supplied in coils of 60m and is
mechanically xed to the construction joint with special clips.
Typical Applications:
Waterproong using hydrophilic swelling and post construction
grouting and leak sealing of construction joints to poured concrete
earth retained structures.
NEWTON 305 ACTIVEJOINTPhysical Movement Joint Water Bar
MDPE physical water bar for the waterproong of movement joints. Thewater bar has a unique V shape with a number of barbs so that water
pressure expands the joint, creating more grip to the concrete joint as the
pressure increases.
Newton 305 ActiveJoint is supplied in eight widths to waterproof
movement joints from between 25mm to 100mm. The product is simply
hammered into a movement joint that has been lubricated with Newton
306 SwellMastic, which is hydrophilic and will swell in contact with water
to further waterproof the joint.
Typical Applications:
Waterproong of movement joints.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 12
8/3/2019 Newton Waterproofing Systems
14/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 300Waterproofing of Concrete Structures
SYSTEM OVERVIEW
NEWTON 306 SWELLMASTICSwelling Adhesive
Newton 306 SwellMastic is a high performance mastic used to adhere
Newton 303 PolyProof and Newton 305 ActiveJoint to the concrete joint.
Can also be used to seal around protrusions such as pipes and conduits
and should be used to reinforce Newton 307 PipeSeal being tted to
pipes passing through the structure.
Newton 306 SwellMastic is supplied in cartridges of 290ml and foil
sausages of 600ml and is applied in a bead.
Typical Applications:
Sealing around protrusions through the structure such as service
pipes and as an adhesive for Newton 303 PolyProof, 304 PolyProofInject and 305 ActiveJoint.
NEWTON 307 PIPE SEALPipe Collar
Newton 307 PipeSeal is a preformed MDPE seal that creates a physical,
anged joint around pipes passing through the structure. Newton 306
SwellMastic should be used to reinforce the joint.
Newton 307 PipeSeal is available for sealing pipes of diameters of
110mm and 160mm and they are simply slipped over the pipe using
neutral soap as a lubricant.
Typical Applications:
Sealing around pipes protruding through the structure.
NEWTON 308 STOPAQ (SX 308)Unique Hydrophilic Polymer Sealant
Newton 308 Stopaq is a unique swelling sealant compound system
which provides a waterproong solution for the notoriously difcult to seal
service pipe penetrations through retaining walls.
Newton 308 Stopaq is supplied in 0.53kg tubes and is applied with a
specialist applicator gun. The product cartridge needs to be warmed prior
to installation by submersing in warm water.
Typical Applications:
Sealing around cables, conduits and other difcult to seal protrusions
through the structure whether in sleeve pipes or directly through the
concrete.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 13
8/3/2019 Newton Waterproofing Systems
15/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 400External Waterproofing
SYSTEM OVERVIEW
NEWTON SYSTEM 400 - EXTERNAL WATERPROOFINGSystem Overview
System 400 is a range of products for the waterproong of the outside
of earth retained structures. Products include sheet membranes for the
complete envelopment of the raft and walls, exible liquid products for the
waterproong of retained walls and composite drainage membranes for
preventing the build up of ground water to the walls or below the raft.
Newton System 400 products can provide Type A and Type B
waterproong to Grades 2 & 3 as dened within BS8102:2009 Code of
Practice for the Protection of Below Ground Structures Against Water from
the Ground.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 14
NEWTON 401 FLEXPROOF-X1Flexible Membrane or Retaining Walls
Newton 401 FlexProof-X1 is a highly advanced single component liquid
waterproong material, which forms an elastomeric polymer membrane
that is rainproof in minutes and capable of handling severe building
movements and deformations.
401 FlexProof-X1 has characteristics that allow it to be used without a
primer, without mixing and in weather conditions that preclude the use of
alternatives.Newton 401 FlexProof-X1 comes in containers of 15kg & 26kg which is
applied by trowel in one coat of 3kg/m2.
Suitable Substrate:
Concrete or masonry retained walls.
Key Benefts
No mixing required simply open the packaging and use.
Can be used in sub-zero temperatures and on slightly damp
substrate.
No primer required saving on primer and labour costs
Single coat application.
100% waterproof, but allows vapour diffusion.
Very exible Resistant to movement and ssures in substrates.
Excellent adhesion to suitable substrates.
Resistant to temperature variations maintaining its characteristics
between -40C & 90C.
Excellent resistance to the high alkalinity of concrete
8/3/2019 Newton Waterproofing Systems
16/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 400External Waterproofing
SYSTEM OVERVIEW
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 15
NEWTON 402 AQUABITFlexible Membrane or Retaining Walls
Newton 402 Aquabit is a single component water based waterproong
bituminous mortar that includes polystyrene micro-spheres that allow it
to be applied obtaining a level of thickness up to 3mm, modied to make
the product extremely workable and able with just one coat to ll surface
irregularities, typical on concrete foundation walls. The material is also
characterised by a high elasticity, crack bridging ability and a good salt
resistance. It can be applied both on old and new walls.
Newton 402 Aquabit comes in containers of 25 litres which is applied by
trowel in one coat of 2.2 litres per m2 to give an average thickness
of 2.5mm.
Typical Applications:
Waterproong of retained walls
NEWTON 403 HYDROBONDHydrophilic and Bonding Membrane or Rat and Wall Waterproong
Newton 403 HydroBond is a very high performance composite sheet
membrane that features a locking eece to one side and a polymer
hydrophilic coating to the other side.
When placed below the new raft or against the wall shuttering, the
poured concrete engages into the locking eece so that the membrane is
completely locked in and monolithic to the concrete thus ensuring that if
a leak did occur it cannot track to the construction joints. The hydrophilic
coating seals small holes that may be accidentally formed during xing of
the reinforcing steel or the pouring or compaction of the concrete.
Newton 403 HydroBond is supplied in rolls of 2m x 30m and can be laid
to the blinding and shuttering of a raft construction or adhered to already
formed retaining walls.
Typical Applications:
Waterproong of retained walls
Waterproong of decks
8/3/2019 Newton Waterproofing Systems
17/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 400External Waterproofing
SYSTEM OVERVIEW
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 16
NEWTON 410 GEODRAIN (M18)Externally Applied Drainage Membrane
Newton 410 Geodrain is a component drainage sheet consisting of a
non-woven geotextile lter layer thermally welded to a water impermeable
HDPE drainage membrane. Newton 410 Geodrain provides outstanding
drainage and protection to the outside face of basement walls, preventing
the build-up of water pressure and protecting the structure from
aggressive water, chemicals and toxins.
Newton 410 Geodrain comes in rolls which are 2m x 12.5m with a surface
coverage of 25m2 (in-line studs 10mm in depth)
Typical Applications:
As the drainage layer of an externally applied waterproong systemwhen used in conjunction with sheet applied or liquid applied external
tanking membrane to BS8102:2009
Protection of the structure from aggressive chemicals in the ground water
To prevent the build up of ground water to retaining walls
8/3/2019 Newton Waterproofing Systems
18/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 500Cavity Drain Waterproofing
SYSTEM OVERVIEW
System Overview
The professionals waterproong system of choice, Newton System 500
is an internally applied waterproong system based upon our range of
cavity drain membranes, drainage conduits and sophisticated pumping
and control systems.
Unlike conventional tanking, Newton System 500 is not attempting the
almost impossible and trying to hold water back, but places designed
maintainable depressurisation voids at known weaknesses in the
structure so that ingressing water is simply captured and diverted out
of the property. Newton recommends that our structural waterproong
systems are installed by one of our Nationwide Network of Newton
Specialist Basement Contractors who have been trained by Newtonand can offer full professional indemnity on design and insured backed
guarantee on the installation.
NEWTON 503 (M5)3mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs
Newton 503 is a BBA approved cavity drain waterproong membrane
suitable for use internally to retaining walls, vaulted softs and oors.
Newton 503 is a exible HDPE membrane which at 0.5mm in thickness
provides a low prole drainage solution within the Newton Cavity Drain
membrane range.
Newton 503 (M5) is available in rolls 2m x 20m - 40m2
NEWTON 503 MESH (M11 & M12)3mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs
Newton 503 Mesh is a BBA certied meshed membrane suitable for use
as a waterproong membrane when used below the ground as part of
Newton System 500.
With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness,
and is the preferred meshed membrane where space is at a premium.
Its meshed surface provides an excellent key for lime mortars, renders,
plasters or dabbed plasterboard. When using Newton 503 Mesh, it is
essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope
as a means of achieving a waterproof seal.
Newton 503 Mesh is available in roll sizes 1m x 20m -
20m2 (M12) and 2m x 20m - 40m2 (M11)
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 17
NEWTON SYSTEM 500 - CAVITY DRAIN WATERPROOFING
8/3/2019 Newton Waterproofing Systems
19/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 500Cavity Drain Waterproofing
SYSTEM OVERVIEW
NEWTON 508 (M1 & M2)8mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs
Newton 508 is our high quality BBA approved cavity drain waterproong
membrane suitable for use internally below the ground to retaining walls,
vaulted softs and oors. Newton 508 is our agship membrane and one
of the most specied cavity drain membranes in the UK. The 0.7mm thick
HDPE product allows for large industrial loads to be applied and the in line
studs allow for quick installation with minimal surface preparation.
Newton 508 is available in roll sizes 2.4m x 20m - 48m2
(M1) and 2m x 20m - 40m2 (M2)
NEWTON 508 MESH (M3)8mm Meshed Cavity Drain Membrane or Basement Walls,
Floors & Vaulted Softs
Newton 508 Mesh is a BBA approved meshed cavity drain waterproong
membrane, suitable for use internally below the ground to retaining walls
and vaulted softs. Newton 508 Mesh is typically used where space
prevents the use of a dry-lining frame or block wall as the wall nish
or where a direct rendered or plastered nish is preferred. The ability
to apply direct nishes to the product makes it ideal for convoluted or
conned basement areas where space is at a premium or where the
original contours (features) of the property need to be retained.
Newton 508 Mesh (M3) is available in rolls 2m x 20m -40m2
NEWTON 520 (M4 & M13)20mm Cavity Drain Membrane or Basement Floors
Newton 520 is a BBA approved cavity drain membrane suitable for use
above basement oor areas. The 20mm studded membrane allows for
a massive ow rate to pass underneath the membrane and is specied
where oor areas are of questionable quality or where it is anticipated
that there may be a risk of severe water penetration.
Newton 520 is available in roll sizes 2m x 20m - 40m2
(M4) or 2m x 10m - 20m2 (M13)
NEWTON BASEDRAIN (D1)Drainage System
Newton Basedrain comprises a range of products that receive water
ingressing at weaknesses within the structure and then discharge the
collected water to a Newton Sump System or safe drainage (drainage that
is below the level of the basement oor that cannot back-up or block).
Basedrain is supplied in packs of 12 linear metres (6 x 2m) lengths.
Internal and external corners, T pieces, drainage connectors and access/
jetting ports should be utilised with Basedrain. Contact us for more details.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 18
8/3/2019 Newton Waterproofing Systems
20/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 600Flooring Membranes
SYSTEM OVERVIEW
NEWTON SYSTEM 600 - FLOORING MEMBRANESSystem Overview
Newton System 600 is a range of HDPE and HDPP ooring membranes
offering a complete damp proof solution for both commercial and
domestic ooring applications. As well as providing protection from
dampness within the oor, our membranes de-couple the oor nish
from the substrate preventing damage due to substrate movement and
cracking. Newton damp proof membranes can be installed over existing
and green concrete.
In addition our ooring membranes are a popular solution for dealing
with inherent hydrocarbons or ground gas problems. Newton ooring
membranes can accommodate a variety of nishes including timber
oors, screeds and direct tiles.
NEWTON 601 SLIMLINE (M6)Flat Loose Laid High Grade Flooring Membrane
Newton 601 Slimline is a high-grade ooring membrane used primarily for
isolating moisture sensitive ooring from dampness in the oor slab, but
can also be used as the oor membrane as part of Newton System 500
when the survey has ascertained that no risk of water entering through
the body of the slab exists.
Newton 601 Slimline allows for the installation of sensitive ooring to
be laid above green still curing concrete as soon as the concrete iswalkable, usually two days, signicantly reducing project times. With a
loading capability of over 1000kN/m2, Newton 601 Slimline is able to
resist very high compressive loading and is suitable for use as a high
load DPC within structural block walls, especially when used to connect
the wall and oor membranes within Newton System 500. Newton 601
Slimline is made from HDPP and is the thinnest prole membrane within
the Newton oor membrane portfolio.
Newton 601 is available in rolls 2.07m x 20m - 40m2 (M6)
NEWTON 603 (M23)
3mm Loose Laid Flooring Membrane
Newton 603 is suitable for use above new and existing oors. The 3mm
studs allow for pressure equalisation of dampness within the oor below
allowing for dissipation at room perimeter and subsequent drying of the
oor. The studs also give slight compression to footfall making the oor
very responsive and comfortable and ideal as the oor membrane for
performance sports oors. Newton 603 uncouples the oor nish from
the substrate so that movement is not transferred to the oor nish
above. The membrane also bridges small cracks allowing for quick oor
installation above less than ideal substrate.
Newton 603 is available in rolls 2m x 20m - 40m2 (M23)
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 19
8/3/2019 Newton Waterproofing Systems
21/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 600Flooring Membranes
SYSTEM OVERVIEW
NEWTON 603 MESH (M24 & M25)Loose Laid 3mm Flooring Membrane with Meshed Surace
Newton 603 Mesh is high grade ooring membrane with an installation
height of 3.5mm. The white HDPE cuspated core has a polyethylene mesh
above allowing for adhesion of the oor nish to the membrane.
Newton 603 Mesh is loose laid above the substrate and is therefore
uncoupled from the oor ensuring that the oor nish is not affected by
movement or cracking of the substrate.
Newton 603 Mesh is available in rolls 1m x 20m - 20m2 (M24) and
2m x 20m - 40m2 (M25)
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 20
8/3/2019 Newton Waterproofing Systems
22/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 700Liquid Applied Floor Coatings
SYSTEM OVERVIEW
System Overview
System 700 is our range of liquid applied protective and decorative
internal ooring products. These products are fast curing and available
in a variety of colours, and are typically used for the refurbishment and
protection of commercial and domestic oors.
NEWTON 701 HB (LM 701)
High Build Epoxy Floor CoatingNewton 701 HB is a two-component solvent free water based epoxy
resin based oor coating developed to provide protective and decorative
properties to concrete, steel and other substrates. The material is
supplied as a two-pack system comprising pre-weighed amounts of base
and curing agent. After mixing together, an easily applied chemical and
abrasion resistant nish is produced. This acts as a waterproof, tough,
chemical resistant oor coating or as an internal lining for concrete or
steel storage tanks containing oils, chemicals, water, etc. It is particularly
suitable for chemical bunds.
Typical Applications:
Food preparation areas Breweries
Industrial units Warehouses
Garages
Below ground structures where Newton drainage conduits are utilised
NEWTON 702 ECOSEAL (LM 702)Highly Resistant Polyurethane Floor Coating
Newton 702 EcoSeal is a two component, solvent free, high performance
Aliphatic Polyurethane resin which provides a hard yet exible oor
coating, with very high abrasion and chemical resistance. It provides
excellent surface protection to oorings exposed to high wear and trafc.
Newton 702 EcoSeal is supplied as a transparent coating for use abovecoloured bases such as Newton 701 HB or it can be coloured on site with
RAL colours through the addition of pigment pastes and used above a
suitable Newton primer as the stand-alone oor nish. The total absence
of solvents allows for application in unventilated indoor areas. Newton
702 EcoSeal cures to a UV stable gloss nish.
Typical Applications:
Heavy trafc areas
Industrial factories, depots and warehouses
Indoor tennis courts and recreational areas
Hard wearing nish to other oor coatings
Indoor car parks
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 21
NEWTON SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS
8/3/2019 Newton Waterproofing Systems
23/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 800Damp Proofing
SYSTEM OVERVIEW
NEWTON SYSTEM 800 - DAMP PROOFINGSystem Overview
Newton System 800 is a range of BBA approved damp proof membranes
and ancillaries which are quick and clean to install and offer a permanent
solution for damp proong walls.
Newton 805 Newlath and Newton 803 Newtonite meshed membranes
provide a rm key and impermeable barrier on any damp or deteriorating
surface ready for plaster, render or dot & dab plasterboard.
The un-meshed Newton 803 is used where insulation requirements
dictate the use of a timber or steel frame ready for plasterboard. Quick,
clean and proven to work, Newton damp proof membranes offer a
permanent and cost effective damp proong solution.
NEWTON 805 NEWLATH (M9 & M10)5mm Meshed Damp Proong Membrane
Newton 805 Newlath (formerly Newlath 2000) is a BBA approved high
density polypropylene membrane with a rot-proof polythene mesh
heat-welded during the manufacturing process to the surface of one side.
The meshed surface creates a mechanical key to allow the membrane to
be plastered, rendered or to receive dot & dab plasterboard. Newlath can
be applied internally as a means of dealing with all forms of dampnessinherent in structures and externally to properties suffering from driving
and penetrating moisture.
With over two million metres of Newton 805 Newlath installed nationally,
Newlath is a cost effective and permanent method of dealing with
dampness.
Typical Applications
Internally for dealing with rising damp, salts and contaminants within
existing structures.
Externally for protection of brick and masonry structures from driving
and penetrating moisture
Treating dampness in listed buildings as the system is deemed
removable and reversible and is sympathetic to the building fabric. Applied to timber frame properties which require a rendered nish.
Newton 805 Newlath is available in rolls 1.5m x 10m -
15m2 (M9) and 2m x 20m - 40m2 (M10)
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 22
8/3/2019 Newton Waterproofing Systems
24/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 800Damp Proofing
SYSTEM OVERVIEW
NEWTON 803 (M19 & M20)Non-Meshed Damp Proong Membrane
Newton 803 is a non-meshed damp proong membrane for use above the
ground. It can be used as an alternative to Newton 803 Newtonite and
805 Newlath where a meshed surface is not required as a surface for
direct plastering or rendering. Newton 803 is typically used where the wall
nish to the damp-proof membrane is timber battens, a dry-lining frame
or block wall.
Newton 803 is 0.5mm thick and has a pattern of raised 3mm studs.
The studs face the wall and create air channels that allow for vapour
equalisation to take place between the membrane and the wall.
Newton 803 is available in roll sizes 2m x 20m - 40m2
(M20) and 1m x 10m - 10m2 (M19)
NEWTON 803 NEWTONITE (M16, M21, M22)3mm Meshed Damp Proong Membrane
BBA approved Newton 803 Newtonite provides a rm key and
impermeable barrier on any damp or deteriorating surface where direct
bonding is not possible. Even poor and random substrates can easily
receive Newtonite.
Newtonite presents a physical barrier between the old surface and thenew internal nish. Unlike many systems it can be punctured when new
wall xings are required. Holes drilled through the material must however
be well sealed with Newton Mastic to stop any dampness
bridging between the existing and new surface.
Newtonite 803 is available in roll sizes:
1m x 10m - 10m2 (M16), 1m x 20m - 20m2 (M21)
and 2m x 20m - 40m2 (M22)
NEWTON 801 FLEXPROOF-X1 (FP1)
Wet-room WaterproongNewton 801 FlexProof-X1 is a highly advanced single component liquid
waterproong material, which forms an elastomeric polymer membrane
that is splash proof in minutes and capable of handling severe building
movements and deformations.
Newton 801 FlexProof-X1 has characteristics that allow it to be used
without a primer, without mixing and in weather conditions that preclude
the use of alternatives. When applied by trowel to wet-room walls, 801
FlexProof-X1 provides a continuous highly exible membrane which can
be blinded with sand ready for the tiled nish.
Newtonite 801 FlexProof-X1 is available in containers of 15kg & 26kg
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 23
8/3/2019 Newton Waterproofing Systems
25/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 800Damp Proofing
SYSTEM OVERVIEW
NEWTON 800 MESH PLUG (A16)Above ground the Newton 800 Mesh Plug can be used internally and
externally to secure Newton meshed membranes: 805 Newlath and
803 Newtonite. Once the hole is drilled it should be primed with Newton
Mastic sealant to prevent dampness tracking back along the plug.
Size (Width x Length) 7mm x 50mm
Quantity Per Bag 250
NEWTON MULTIPLUG (A1)
Newton MultiPlug is used with Newton 803. Drill a 10mm hole through
the 803 membrane and hammer home with a club hammer. The
MultiPlug can take a 5mm dia screw to allow the xing of battens and
dry-lining frames and the Newton Helix Wall Tie without breaching
the membrane. MultiPlug Pins are sold separately.
NEWTON 800 COB PLUG (A17)
In above ground situations, the Newton Cob Plug is used with 803
Newtonite and 805 Newlath membranes. It has an expanding stem which
provides effective anchorage in a wide range of base materials. Larger
sizes of Newton Cob Plug can be sourced on request.
The ancillaries below are used with the three damp-proong membranes that are included within Newton System
800. Newton 803 is a plain membrane used where a dry-lining frame or a block wall is to be used as the wallnish. 803 Newtonite and 805 Newlath are meshed membranes used where a surface key is required for direct
plastering, rendering or dot and dabbing to the wall membrane. Please read the membrane product data sheets
for more information.
Membrane Fixing Plug Jointing Tape Sealing Drilled Hole Plaster Stop Repairs
803 MultiPlug Newton Overtape Not Required Not required Newton Overtape
803 Newtonite 800 Mesh or
Newtonite Plug
Newton Mesh Tape Newton 800 Mastic Newton 800 Prole Newton Mesh Tape
805 Newlath 800 Mesh or
Newtonite Plug
Newton Mesh Tape Newton 800 Mastic Newton 800 Prole Newton Mesh Tape
Size (Width x Length) 10mm x 57mm
Quantity Per Bag 100
Size (Width x Length) 7mm x 90mm
Quantity Per Bag 50
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 24
NEWTON 800 NEWTONITE PLUGS (A20)
Above ground the Newtonite Plugs can be used internally to secure
Newton 803 Newtonite and 805 Newlath membranes. Once the hole
is drilled it should be primed with Newton Mastic sealant to prevent
dampness tracking back along the plug.
Size (Width x Length) 7mm x 50mm
Quantity Per Bag 160
8/3/2019 Newton Waterproofing Systems
26/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 800Damp Proofing
SYSTEM OVERVIEW
NEWTON 800 MASTIC (A18)Newton Mastic is used with 805 Newlath and 803 Newtonite. It is used
to prime the plug hole prior to the xing plug being hammered home,
which serves to stop any bridge happening between the damp or stained
surface and the new surface. Newton Mastic is also used for sealing
around protrusions.
Unit o Sale 0.38 litre tube
NEWTON MESH TAPE (A25)
Newton Mesh Tape is used to joint 803 Newtonite and 805 Newlath
membranes as well as for repairs to the membrane and for sealing
around protrusions. The meshed surface gives a good key for renders
and plasters.
Size (Width x Length) 100mm x 10m
Unit o sale Single units
NEWTON OVERTAPE (A8)
Newton Overtape is used for the jointing of Newton 803 as well as for
repairs to Newton 803 and to seal around protrusions to the membrane.
NEWTON 800 PROFILE (A19)
Newton Prole can be used with 803 Newtonite and 805 Newlath. It
serves as a plaster stop, guaranteeing that the plaster/render will stop
short of the oor.
Size 2m lengths
Unit o Sale Single units
Size (Width x Length) 100mm x 20m
Unit o sale Single units
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 25
8/3/2019 Newton Waterproofing Systems
27/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 900Liquid Primers & Sealers
SYSTEM OVERVIEW
NEWTON SYSTEM 900 - LIQUID PRIMERS & SEALERSSystem Overview
Newtons high performance range of liquid applied products are used in
conjunction with System 200 and 700 liquid membranes. They act as
priming agents for a variety of substrates prior to the application of our
specialist waterproong and ooring membranes.
NEWTON 901 HUMIDITY PRIMER (PS 901)Epoxy Primer Suitable or High Humidity Substrate
Newton 901 Humidity Primer is a solvent free two part epoxy resin coating
typically used as a primer for Newton high performance liquid applied or
sprayed roong and ooring products.
Newton 901 Humidity Primer would be chosen as the primer coating
where the substrate contains humidity levels in excess of 4%.
Application
Mix Part A - Epoxy Resin with Part B - Hardener thoroughly with an electric
paddle mixer for 2 min until a milky uniform colour is achieved (pot life of
approx 30 minutes)
Application rate is 0.3 kg per m2 dependent on the quality of the
substrate. Newton 901 Humidity Primer is supplied in 5kg, 10kg and20kg components.
NEWTON 902 (PS 902)Liquid Applied Radon, Gas & Vapour Barrier
Newton 902 is a single component high performance elastomeric liquid
rubber membrane specically designed for providing a radon, gas and
vapour barrier to vertical and horizontal surfaces. Newton 902 is a cost
effective vapour barrier material which can easily be applied via a stiff
brush, roller or airless sprayer to a variety of different substrates including
concrete, mortar, brick, Insulated Concrete Formwork (ICF), ceramics,
steel, zinc or aluminium.
Pre-dampen porous substrates prior to the application of the rst coat.
Application
Newton 902 can be used as a primer for other Newton liquid membranes
when applied in one coat of 0.33kg per m2 or as a gas, vapour and
waterproong membrane with two coats totalling 1kg per m2
Newton 902 is supplied in 5kg, 10kg and 20kg tubs.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 26
8/3/2019 Newton Waterproofing Systems
28/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SYSTEM 900Liquid Primers & Sealers
SYSTEM OVERVIEW
NEWTON 903 PU PRIMER (PS 903)Epoxy Primer or Nonporous Substrate
Newton 903 PU Primer is used for priming non-absorbent substrates,
prior to application of Newton high performance liquid applied roong and
ooring products.
It should be chosen as the primer where the substrate is nonporous such
as ceramic, steel, glass, marble, polished concrete etc.
Newton 903 PU Primer can be applied with roller, brush or cloth to a ratio of
0.1kg per m2
Newton 903 PU Primer is supplied in units 4kg, 9kg or 20kg
NEWTON 904 HP ACCELERANT (PS 904)Humidity Primer Accelerant
Newton 904 HP Accelerant is a clear accelerant additive for exclusive
use with Newton 901 Humidity Primer. The addition of Newton 904 HP
Accelerant to Newton 901 Humidity Primer results in the primer being
cured in 1 to 2 hours (diminishing the risk of alteration by rain, wind, etc.)
The accelerated curing is achieved without any loss in its properties or
changes in the chemical structure of the primer.
Newton 904 HP Accelerant is supplied in 1kg units and has been
designed to be added to a 20kg unit of Newton 901 Humidity Primer.
Add the 1kg unit of Newton 904 HP Accelerant to the 20kg unit of the
901 Humidity Primer once both parts A and B have been already mixed.
Totally mix and homogenise both products together.
Note: After adding 904 HP Accelerant to the 901 Humidity Primer the pot
life is shortened to only 20-30 minutes and the combined product cannot
be reused.
NEWTON 906 MOULD STOP (PS 906)
Mould Steriliser & KillerNewton 906 Mould Stop can eradicate mould in four easy steps. It is
simple to use and as well as killing dangerous mould it prevents regrowth
and eliminates musty odours.
Newton 906 Mould Stop is suitable for walls, ceilings, skirting boards,
window reveals, uPVC window and door frames.
906 Mould Stop kit contains: 1 litre of Mould Stop Steriliser and Killer
Spray, 1 x safety glasses, 1 x pair of disposable gloves, 1 x sponge and
2 x 100ml Mould Stop Paint Additive.
Once mixed Newton 906 Mould Stop will treat between 10 and 15m2
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 27
8/3/2019 Newton Waterproofing Systems
29/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON FLEXPROOFConstruction Joint Waterproofing
SYSTEM OVERVIEW
NEWTON FLEXPROOFHighly Advanced Single Component Liquid Waterproong Material
Newton FlexProof-X1 forms an elastomeric polymer membrane that is
rainproof in minutes and capable of handling severe building movements
and deformations.
FlexProof-X1 has characteristics that allow it to be used without a primer,
without mixing and in weather conditions that preclude the use of
alternatives.
FlexProof-X1 is a multi-use product and can be applied by trowel or
squeegee to a variety of different surfaces such as concrete, screed and
timber boards to provide a continuous highly exible membrane that is
resistant to water pressures of up to 2 bar (20m) over construction jointsof up to 0.25mm.
Key Benefts:
No mixing required - simply open the packaging and use.
Can be used in sub-zero temperatures and on slightly damp
substrate.
No primer required - saving on primer and labour costs
Single coat application.
100% waterproof, but allows vapour diffusion.
Very exible - Resistant to movement and ssures in substrates.
Excellent adhesion to suitable substrates.
Resistant to temperature variations maintaining its characteristics
between -40C & 90C.
Excellent resistance to the high alkalinity of concrete.
NEWTON FLEXPROOF-X1 (FP1)Construction Joint Waterproong
For the waterproong of construction joints in new-build concrete
construction of basements. When applied by trowel or squeegee over
construction joints in concrete, FlexProof-X1 provides a continuous highlyexible membrane that is resistant to water pressures of up to 2 bar
(20m) over construction joints of up to 0.25mm.
Suitable Substrate:
Construction and movement joints to basement structures built of
concrete.
Retained walls built in concrete or concrete block.
Construction and movement joints to decks and at roofs built of
concrete or timber.
Wet rooms built of concrete, masonry or timber.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 28
8/3/2019 Newton Waterproofing Systems
30/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON DIATHONITEInsulating Plaster
SYSTEM OVERVIEW
NEWTON DIATHONITEEco Thermal Plaster with Insulation and Acoustic Properties
Newton Diathonite is a premixed plaster, bre-reinforced with cork
(granular 0-3 mm), clay powders and NHL 3.5 natural hydraulic lime.
The resulting natural compound produces a plaster with unrivalled
thermal and acoustic properties that is both hard wearing and exible
which is ideal for both internal and external applications.
Diathonite, when applied either internally or externally, creates a
seamless thermal barrier which eliminates any risk of cold bridging within
the structure. To achieve very high thermal and acoustic performance,
Newton Diathonite will need to be applied at a thickness that is similar to
those of standard wall insulation.
One of the big advantages of applying Newton Diathonite to existing
properties is that the application can be split between internal and
external application, whereas conventional insulation can only be added
to the inside of the walls and so impacts greatly on the internal space.
It is usual for the internally applied insulation to then have a covering,
such as plasterboard, which further reduces habitable space. By splitting
the application of Diathonite between the inside and outside of the wall,
similar insulation characteristics can be achieved with just half the space
loss of conventional insulation.
Key Benefts
Superb insulation properties thanks to the air spaces created by
natural cork particles included within the plaster
High vapour permeability
Resistant to re: Class 1
Eco-friendly
Can be spray applied allowing for very fast application
Very exible - large elevations can be plastered without cracking
Impressive acoustic characteristics - over twice the performance of
conventional plasters or renders
Typical Applications
As a high performance insulated plaster for both the inside and
outside of external walls
As a sound insulating plaster for both external and internal walls
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 29
8/3/2019 Newton Waterproofing Systems
31/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SUMP AND PUMPPumping Product Range
SYSTEM OVERVIEW
NEWTON SUMP AND PUMPSystem Overview
Newton have an extensive range of submersible pumps and pumping
ancillaries. We supply the highest quality pumps available in each class,
for the control of clean ground water, grey water, efuent or sewage.
CLEAN/GROUND WATER PUMPS
NEWTON NP150 (P1)
Medium head and low to medium duty pump. The NP150 is an automatic
pump, with integral vertical oat switch and so is not suitable for use with
our pump control panels. It can be used with Newton Power Converters of
1200W or over to give continual pumping even when the power is out.
The NP150 is supplied with a one way check valve and should be used
with 50mm pressure rated discharge pipe. The pump is sold as pump
only, or as a key component in our Newton Titan-2 packaged pump
system.
3 year manufacturers warranty.
NEWTON CP250 (P31)
The Newton CP250 is a low cost and high quality clean water pump ideally
suited for the removal of ground water from basements and cellars. The
unique vertical operation oat switch ensures that the pumps operate
within the pump footprint removing the possibility of the oat snagging
during operation and allowing the pumps to be used within smaller
sumps. The vertical oat switch is also very exible, allowing the pump
switching height to be adjusted both in height between the on and off
positions, but also in height relative to the pump.
The CP250 is supplied with a one way check valve and and should be
used with 50mm pressure rated discharge pipe.
The pump is sold as pump only, or as a key component in our Newton
Titan-2 and Newton Titan-Pro packaged pump systems.
1 year manufacturers warranty or 3 year Newton warranty with proven
service history.
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 30
8/3/2019 Newton Waterproofing Systems
32/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SUMP AND PUMPPumping Product Range
SYSTEM OVERVIEW
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
NEWTON CP400 (P32)
The Newton CP400 is a low cost and high quality clean water pump ideally
suited for the removal of ground water from basements and cellars. The
unique vertical operation oat switch ensures that the pumps operate
within the pump footprint removing the possibility of the oat snagging
during operation and allowing the pumps to be used within smaller
sumps. The vertical oat switch is also very exible, allowing the pump
switching height to be adjusted both in height between the on and off
positions, but also in height relative to the pump.
The CP400 is supplied with a one way check valve and should be used
with 50mm or 63mm pressure rated discharge pipe. The pump is sold
as pump only, or as a key component in our Newton Titan-2 and Newton
Titan-Pro packaged pump systems.
1 year manufacturers warranty or 3 year Newton warranty with proven
service history.
NEWTON NP400 (P2 & P3)
Available in both manual (P3) and automatic (P2) versions, the NP400 is
the most popular high performance submersible pump in our portfolio.
The NP400 has a unique vertical oat mechanism which can be adjusted
to suit each individual pumping assignment. It can be used with Newton
Power Converters of 1200W or over to give continual pumping even when
the power is out.
The NP400 is supplied with a one way check valve and should be used
with 50mm or 63mm pressure rated discharge pipe. The pump is sold
as pump only, or as a key component in our Newton Titan-2 and Newton
Titan-Pro packaged pump systems.
3 year manufacturers warranty.
NP400PP (P13) & NP400LLPS (SP1)
The Newton NP400PP is a high quality puddle pump able to pump water
down to just 1mm. The NP400PP is a manual pump with no switching
control - the pump will run continually when connected to a power supply.
Switching of puddle pumps is problematic because by their nature they
are dealing with low heights of water. This makes conventional switchingdifcult.
The NP400LLPS is the switched version of the NP400PP Puddle Pump.
The NP400LLPS has a small control panel and low level switching
module added to the NP400PP Puddle Pump that will give accurate and
safe switching on of the pump at water levels of just 10mm. The NP400
LLPS will pump down to just 1mm of water depth. The NP400PP and
NP400LLPS are supplied with a one way check valve and should be used
with 50mm pressure rated discharge pipe.
3 year manufacturers warranty.
Page 31
8/3/2019 Newton Waterproofing Systems
33/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SUMP AND PUMPPumping Product Range
SYSTEM OVERVIEW
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 32
NEWTON CP750 (P33)
The Newton CP750 is a low cost and high quality clean water pump ideally
suited for the removal of ground water from basements and cellars. The
unique vertical operation oat switch ensures that the pumps operate
within the pump footprint removing the possibility of the oat snagging
during operation and allowing the pumps to be used within smaller
sumps. The vertical oat switch is also very exible, allowing the pump
switching height to be adjusted both in height between the on and off
positions, but also in height relative to the pump.
The CP750 can be supplied with a choice of one way valves and should
be used with 50mm or 63mm pressure rated discharge pipe.
The pump is sold as pump only, or as a key component in our Newton
Titan-Pro packaged pump system.1 year manufacturers warranty or 3 year Newton warranty with proven
service history.
NEWTON NP750 (P5 & P6)The Newton NP750 is a high performance pump available as an
automatic pump (P5), or as a manual pump (P6) for use with the CP2
Control Panel. It can be used with Newton Power Converters of 3000W to
give continual pumping even when the power is out.
For increased duty in a twin pump system, separate discharge lines
should be used. The NP750 is sold as pump only, or as a key component
in our Newton Titan-Pro packaged pump system and should be used with
50mm or 63mm pressure rated discharge pipe.
3 year manufacturers warranty.
EFFLUENT PUMP (NOT SEWAGE)
NEWTON NP400W (P4)
The Newton NP400W is a medium head and medium performance pump
specically placed within the Newton pumping range for when dishwasher,
washing machine or bath/shower waste is to be removed from thesump. It is an automatic pump with a specially designed adjustable oat
arrangement that cannot be fouled by hardened soaps etc. It can be
used with Newton Power Converters of 1200W or over to give continual
pumping even when the power is out.
The NP400W is sold as pump only, or as a key component in our Newton
Titan-Pro packaged pump system and should be used with 50mm and
63mm pressure rated discharge pipe.
3 year manufacturers warranty.
8/3/2019 Newton Waterproofing Systems
34/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SUMP AND PUMPPumping Product Range
John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217
www.newton-membranes.co.uk - [email protected]
Page 33
SEWAGE PUMPS
NEWTON SP750 RANGER (P9)
The Newton SP750 Ranger is a low head and high performance sewage
pump for the removal of sewage, efuent, waste water and ground water
with suspended soft solids of up to 50mm.
The Newton SP750 Ranger is primarily used as the standard pump in our
Trojan sump systems but can also be used as a stand-alone pump within
formed concrete sumps and should be used with 63mm pressure rated
discharge pipe.
1 year manufacturers warranty.
NEWTON FLYGT DXG (GRINDER) (P14 & P16)
The Newton Flygt DXG (Grinder) is a high performance submersible
grinder pump which cuts solids in sewage into smaller bits that can easily
pass through the impeller and discharge pipes.
The Newton Flygt DXG is primarily used as the standard pump in our
Trojan sump systems but can also be used as a stand-alone pump within
formed concrete sumps and should be used with 50mm pressure rated
discharge pipe.
1 year manufacturers warranty.
Available in Automatic (P14) or Manual (P16) versions.
SEWAGE LIFTING STATION
TROJAN SEWAGE PUMPING SYSTEM (TR1-TR12)
Newton Trojan systems are specialist packed sewage systems based upon
a 610mm diameter sump with depth options of 1000mm and 1500mm.
The Trojan systems are supplied as either single or twin pump systems
using the Newton 750 Trojan (Vortex) or Newton Flygt DXG (Grinder).
A hole cutter and 1 x 110mm wall ange is supplied allowing for accurate
on-site positioning of the invert connection.
Note: The Trojan System is not supplied with a High Water Level Alarm -
Alarm and pump control options are available at extra cost.
SYSTEM OVERVIEW
8/3/2019 Newton Waterproofing Systems
35/42
J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k
NEWTON SUMP AND PUMPPumping Product Range
CLEAN/GROUND/EFFLUENT PUMPING SYSTEMS
TITAN-PRO WHITE (TPW)
The Newton Titan-Pro White is designed specically to be used with
Newton System 500. The adjustable neck allows for the sump to be
installed at a xed height relative to the slab so that the connection in
from the Newton drainage system and the pump discharge line are made
above the concrete.
The sump can be used with single pumps, twin pumps and twin pumps
with twin discharge lines for greater pump efciency.
The Titan-Pro White is available with the following pumps: CP250,