OL-O-1655
OOll iivveerrOperator’s Manual
1655
THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF OLIVER OR IT’S SUCCESSORS. OLIVER AND IT’S SUCCESSORS
ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY OF THIS MANUAL.
TRADE MARKS AND TRADE NAMES CONTAINED AND USED HEREIN ARE THOSE OF OTHERS, AND ARE USED HERE IN A DESCRIPTIVE SENSE TO REFER TO THE PRODUCTS OF OTHERS.
Ope
rato
r’s M
anua
l
Make: Oliver Model: 1600 Years Made: 1962-1964 Make: Oliver Model: 1650 Years Made: 1964-
1969
HP-PTO: 57.95 HP-Engine: HP-Drawbar: 46.9 HP-PTO: 66.28 HP-Engine: HP-Drawbar: 56.5
HP-Range: 58 Engine-Make: OLIVER
Engine-Fuel: DIESEL HP-Range: 66 Engine-Make:
OLIVEREngine-Fuel: DIESEL
Engine-Cyl(s)-CID: 6/265
Transmission-STD: HYDRA-POWER
Optional: Engine-Cyl(s)-CID: 6/283
Transmission-STD: HYDRA-POWER
Optional: CREEPER
Fwd/Rev Standard: 12/
Fwd/Rev Optional: Mfwd-Std/Opt: Fwd/Rev Standard:
12/2Fwd/Rev Optional:
Mfwd-Std/Opt: OPT
Tires-Std Front: 6.50-16
Tires-Std Rear: 16.9-34 Wheelbase-Inch: Tires-Std Front: 6.50-
16Tires-Std Rear: 15.5-38
Wheelbase-Inch: 99.25
Pto Type: Pto Speed: CAT I-3pt Hitch: False Pto Type: IND Pto Speed: 540
1000CAT I-3pt Hitch: True
CAT II-3pt Hitch: False
CAT III-3pt Hitch: False Hitch Lift: CAT II-3pt Hitch: True CAT III-3pt
Hitch: False Hitch Lift:
Hydraulics-Type: Hyd-Cap: Hyd-Flow: Hydraulics-Type: CLOSED Hyd-Cap: 20 Hyd-Flow:
Hyd Std Outlets: Cooling Capacity:
Fuel Tank Capacity: Hyd Std Outlets: 2 Cooling
Capacity: 20Fuel Tank Capacity: 27.5
Cab-Stdm A/C; Rops: Weight: 7180 New Price: 4496 Cab-Stdm A/C; Rops: OPT Weight: 7815 New Price: 6991
Make: Oliver Model: 1655 Years Made: 1969-1975 Make: Mpls-Moline Model: G-750 Years Made: 1971-
1972
HP-PTO: 70.57 HP-Engine: HP-Drawbar: 60.0 HP-PTO: 70 HP-Engine: HP-Drawbar:
HP-Range: 71 Engine-Make: OLIVER
Engine-Fuel: DIESEL HP-Range: 70 Engine-Make: M-
M Engine-Fuel: GAS
Engine-Cyl(s)-CID: 6/283
Transmission-STD: SG
Optional: HYDRA-POWER
Engine-Cyl(s)-CID: 6/265
Transmission-STD: CM
Optional: HYDRA-POWER
Fwd/Rev Standard: 6/2
Fwd/Rev Optional: 18/3
Mfwd-Std/Opt: OPT
Fwd/Rev Standard: 6/2
Fwd/Rev Optional: 18/6
Mfwd-Std/Opt: OPT
Tires-Std Front: 7.50-16
Tires-Std Rear: 18.4-34
Wheelbase-Inch: 99
Tires-Std Front: 6.50-16
Tires-Std Rear: 126.9-38
Wheelbase-Inch: 99.25
Pto Type: IND Pto Speed: 540 CAT I-3pt Hitch: True Pto Type: IND Pto Speed: 540 CAT I-3pt Hitch:
True
CAT II-3pt Hitch: True CAT III-3pt Hitch: False Hitch Lift: CAT II-3pt Hitch: True CAT III-3pt
Hitch: False Hitch Lift:
Hydraulics-Type: OPEN Hyd-Cap: 14 Hyd-Flow: Hydraulics-Type: Hyd-Cap: 14 Hyd-Flow:
Hyd Std Outlets: OPT Cooling Capacity: 20
Fuel Tank Capacity: 27.5 Hyd Std Outlets: OPT Cooling
Capacity: 20Fuel Tank Capacity: 27.5
Cab-Stdm A/C; Rops: OPT Weight: 7500 New Price: 9984 Cab-Stdm A/C; Rops:
OPT Weight: 7500 New Price: 7479
Year Beginning Serial Number Year Beginning Serial Number
1964 147569 1962.0 124420
1965 153855 1963.0 127044
1966 167668 1963.0 137710
1967 183923 1964.0 140723
1968 201091
1969 212733 1971 225997
1976 266173 1969 218025
1977 274543 1970 220401
1978 283917 1971 222761
1979 287528 1972 231772
1980 293819 1973 236586
1981 296246 1974 244735
1982 299887 1975 257700
Paint Codes Paint Codes
Location MFG Color Name Location MFG Color Name
BODY OF TRACTOR OLIVER GREEN RIMS ALUMINUM
TRIM & WHEELS CLOVER WHITE TRIM WHITE
BODY & WHEELS MM YELLOW
LOWER INSTRUMENT PANEL, LH SIDE 1655INSTRUMENT PANEL WHITE 2-70
MM G750
LOWER INSTRUMENT PANEL, LH SIDE 1650 TRANS CASE, LH SIDE or REAR SIDE OF INSTRUMENT PANEL SUPPORT 1600
"-." .
_________________ .,_..,. ...... ~.::., • .II ... ~."'.~ f>' W' . .. ~ •. .. '_", ____________________ _
INTRODUCTION
This Operator's Manual is presented to furnish you with necessary information for operating and maintaining your tractor. Its primary purpose is to assist you in lubricating and adjusting the tractor for daily and seasonal operation. We especially wish to call your attention to the many safety Slogans listed in this manual. Although your tractor is designed with the safety of operation in mind. possibilities of accidents cannot be completely eliminated until you understand and practice all safety precautions.
Timely service saves costly repairs and valuable time lost because of breakdowns. Whenever it becomes necessary to make REPAIRS or REPLACEMENTS on your tractor, be sure to insist on GENUINE PARTS. These. parts are designed specifically for your tractor under controlled specifications to give satisfaction and long lasting service to which you are entitled. YOUR DEALER CAN SUPPLY YOU WITH PARTS YOU REQUIRE. For additional information consult your dealer.
TABLE OF CONTENTS
Specifications .••.••.•..•..•.•..••••••••••• Section I
Safety Instructions ••••••••••••••••••••••••••• Section II
Lubrication Section III
Operation ••..•••••••••••••••••••••••.••• Section IV
Adjustments ••••••••••••••••••• • " •••••••••• • Section V
Service & Troubleshooting •••••••••••••••••••• Section VI
Optional Equipment ••••••••••••••••••••••••• Section VII
Index •••••.••.•.••.••••••••••.••.••••• Section VIII
SPECIFICATIONS
IGNITION AND ELECTRICAL
Spark Plugs - 14mm - 13/16 in. - Electrode Gap 0.025 in.
Gasoline
A.C. Autolite Champion Prestolite
LP Gas
A.C. Autolite Champion Prestolite
Battery Number
Gasoline and LP Gas Diesel
Capacity Gasoline and LP Gas Diesel
Group Gasoline and LP Gas Diesel
Distributor (Gasoline and LP Gas) Rotation Point Gap
Lights Floodlights
Type Size Capacity
Taillight Type Size Capacity
Instrument Background Lights Type Size Capacity
Fuses
1·4
Lights Instruments Hydra-Lectric
Heavy and Normal Duty
44XLS AG42 N-ll-Y 14GT42
All Duty
C44XL AG4 N6 14G3
1 (12 Volt)
Light Duty
45XLS AG52 N-14-Y or UN-12-Y 14G52
2 (6 Volt in Series)
70 amp - hrs. 168 amp - hrs.
15M4A (SAE). 60 (AABM) 5D (AABM)
Clockwise 0.025 in.
Sealed Beam 35 watt 12-16 volt
Bayonet 4 candle power 12-16 volt
Bayonet 2 candle power 12-16 volt
1-1/4 in. x 1/4 in. 20 amps (1) 1-1/4 in. x 1/4 in. 3 amps (1) 1-1/4 in. x 1/4 in. 30 amps (1)
LUBRICATION
ENGINE CRANKCASE
Lubricant
Refer to Engine Oil specifications in Section I for lubricant recommenda tions.
Checking Lubricant Level
With tractor on level ground. check oil level daily or every 10 hours of operation and replenish. if necessary. to maintain level between FULL-LOW marks on dip stick. To remove dip stick on gasoline and diesel models. turn handle counterclockwise and remove. Check oil level when engine is stopped. If engine has been in operation. be sure to allow sufficient time for oil to drain into pan before checking level. Dip stick oil filler opening is on left side of engine except on LP gas tractors where dip stick is on left side of engine and oil filler opening is on right side.
Changing Lubricant
Crankcase oil change frequency depends heavily upon working conditions. Under normal operating conditions drain gasoline or diesel engine oil every 100 hours of operation and LP gas engine oil every 150 hours of operation. Change oil more often when tractor is operated during winter months or in extreme dust conditions.
Remove drain plug and drain oil while engine is warm so tha t it will flow freely. Reinstall drain plug and refill crankcase with recommended lubricant.
ENGINE OIL FILTER
Gasoline and LP Gas
Remove and discard gasoline or LP gas engine oil filter element every second oil change. Remove element from base by turning counterclockwise. Lubricate rubber gasket 011 new element. part number 169 019-A. with heavy oil or grease prior to installation. Thread element onto base. turning clockwise no more than one-half turn after gasket first contacts base. Check and replenish engine oil level after initial operation whenever an element is replaced and check for leakage.
3-3
DEPTH STOP
4716
4 -16
OPERATION
Cylinder Control Levers (Industrial and Depth-Stop,
External Valve)
Two cylinder control levers are normally provided; left lever controls cylinders attached to left couplings on rear of seat support; right or second lever controls cylinders attached to right couplings. If a third or fourth valve is installed, third or fourth control lever will control cylinder attached to its valve. Valves may be actuated individually or together. Recommended engine speed for operating depth -stop cylinders is 1000 rpm or above.
Adjusting Cylinder Depth (Hydra-Lectric-Stop)
To increase working depth of implement controlled by a HydraLectric-Stop cylinder. hold external cylinder control lever forward until piston rod stop collar corresponds with desired depth. Release lever.
To decrease working depth of implement controlled by a HydraLectric-Stop cylinder, move control lever forward and allow it to return to neutral automatically. Depress lever switch button and move lever rearward. Release switch and lever when desired stop collar setting is obtained.
Adjusting Cylinder Depth (Depth Stop)
To adjust cylinder depth, extend cylinder and loosen stop adjusting screw. Position stop as required and tighten screw.
A Adjustable Axle Adjustment Air Cleaner Air Stack Cap Air Preheater Switch, Diesel Ammeter Anti-Roll Bar
Backrest, Upper
B
Battery Service and Replacement Belt Pulley
Breather Installation and Operation Lubrication Specifications
Bleeding Diesel Fuel System Blocking Valve Adjustment Brake Adjustment Brake Pedals Breaking In New Tractor Bypass Valve Adjustment
INDEX
SECTION VIII
INDEX
4-3,
4-21 6-4 6-5 4-8 4-3 7-5
7-4 6-8
3-9 4-21 3-9 1-1 6-6 4-5 5-6 4-4 4-1
5-19
Cab Air Filter Controls Coolant Valve Defroster Fan Windows
c
As Optional Equipment Capacities Carburetor Adjustments
Gasoline LP Gas
Chain Coupling Lubricant Checking Tractor Choke Control, Gasoline and LP Gas Cigar Lighter Clevis, Drawbar Clutch Adjustment
Engine Power Take-Off
Clutch Pedal, Engine Control Levers
Creeper Drive External Cylinder Governor Hydra -Power Drive Over/Under Hydraul-Shift Power Take-Off Three-Point Hitch
Controls and Instruments Coolant Heater Cooling System Creeper Drive
Control Rod Lubrication Unit capacity
6-6 4-25, 4-26
4-26 4-26 4-26
7-3 1-8
5-1 5-2 3-7 4-1
·4-2 4-2 7-4
5-6 5-7 4-4
4-3 4-15, 4-16
4-3 4-3 4-3
4-20 4-10
4-2 7-1
6-13
4-3 3-7 1-8
8·1
Defroster Fan Depth Stop Cylinders
Adjusting Depth Connecting Control Levers Support Bracket
D
Depth Stop Hydraulic Systems Restrictor Valve Adjustment Specifica tions Troubleshooting
Dimensions, Tractor Distributor
Checking Lubrication Points
Draft Control Adjustment Drawbar Adjustment Drawbar Clevis Drawbar Roller, Lubrication Dual Rear Wheels
Electrical Specifications Engine
Break in Procedure Lubrication Oil Filter Oil Pressure Gauge Oil Specifications Operation Specifications Starting Procedure Stopping T rou bleshooting
External Cylinders
E
Extra High Clearance Final Drive Housing Lubrication
F Fan Belt Filters
8-2
Cab Air Fuel, Gasoline Fuel. Diesel Fuel, LP Gas Oil, Engine Oil, Hydra -Power Drive Oil, Reverse-O-Torc Oil, Transmission and Final Drive
INDEX
Final Drive Lubrication 3-4 Four-Wheel Drive
4-26 Axle Shaft Joint Housings Lubrication 3-16 Front Axle Differential Lubrication 3-15
4-16 Front Axle Load Capacities 1-6
4-13, 4-14 Grease Fittings
4-15, 4-16 Drive Shaft 3-17
4-17 Pivot Pins and Thrust Plates 3-17 Steering Cylinder Anchors 3-18
4-17, 4-18 Steering Trunnions 3-18
1-3, 1-8 Transfer Drive Case Output Shaft 3-17
6-18 Planetary Drives 3-16
1-7 Shifter Rod 4-4 Tire Recommendation, 4WD 1-6
6-12 Transfer Drive Case
3-10 Breather 3-15
6-12 Lubrication 3-14
4-11 Front Axle
I-I, 4-19 A dj ustment, Adjustable Axle 4-21
7-4 Lubrication 3-12
3-11 Toe-In Adjustment 5-8
7-5 Front Frame Weights 7-2 Front Wheel Bearings
Adjustment 5-6, 5-7
1-4 Lubrication 3-13 Front Wheel Tread Adjustment 4-22
4-1 Fuel 3-3 Bleeding Diesel System 6-6
3-3, 3-4 Filter, Gasoline 6-4
4-3 Filter, LP Gas 6-6
1-2 Filters, Diesel 6-7
4-9 Gauge 4-2
1-2 Storage 4-5
4-7 Strainer, Gasoline and Diesel 6-3
4-9 Specifica tions 1-2
6-15 Tank, Filling 4-5
4-13 Fuses 6-12
3-18
5-8
6-6 G 6-4 6-7 Gauges 4-2 6-6 Gear Shift Lever 4-3
3-3, 3-4 Governor Adjustments 3-8 Gasoline and LP Gas 5-3 3-8 Diesel 5-5 3-5 Governor Control Lever 4-3
INDEX
Horsepower Hydraulic
Breather
H
Bypass Valve Adjustment Control Levers Couplings Fluid Fluid Filter Interlock Bleed Screw Adjustment Restrictor Valve Adjustment Specifica tions Trouble Shooting
Hydra-Lectric Cylinders Adjusting Depth Connecting Contro~ Levers
Hydra-power Drive Control Rod Lubrication Oil Filter
Idle Speed Adjustment Diesel Gasoline LP Gas
Ignition and Electrical Specifications Ignition Switch Ignition, Timing Imperial and Metric Measure Implement Categories
1-2
3-6 4-19
4-10, 4-15, 4-16 4-14
3-5, 3-6 3-6
4-18 4-17, 4-18
1-3, 1-8 6-18
-4-16 4-13 4-15
4-3 3-7 3-8
5-5 5-1 5-3 1-4 4-3 5-4 1-1
Inflation and Load RecommendatiOlls, Tire Instruments and Controls
4-12 1-5 4-2
4-18 Interlock Bleed Screw Adjustment
L Leveling Adjustment Leveling Gear, Lubrication Lift Links, Lubrication Light Switch Lighter, Cigar LP Gas Fuel System Adjustments Lubrication Chart
M Manual Steering Gear Lubrication Metric and Imperial Measure
4-13 3-11 3-11 4-2 4-2 5-2 3-2
3-9, 3-10 1-1
o Oil Change Periods, Engine Oil Filters
Engine Hydra-Power Drive Reverse-O -Torc Transmission and Final Drive
Oil Pressure Gauge Oil Specifications, Engine Oil Temperature Gauge Over/Under Hydraul-Shift
Control Lever Lubrication Oil Filter Unit Capacity
Pedal Extension
p
Pitman Shaft Bearings Lubrication Powerj uster Wheels Power Steering Pump
Drive Belt Adjustment Lubrication Specifications
Power Take-Off Clutch Adjustment Control Lever Adjustment Lever Shaft Lubrication Operation Specifications
Prec1eaner, Air Preheater Switch, Diesel
3-3,
3-3
3-4 3-8 3-8 3-5 4-3 1-2
4-22
4-3 3-7 3-8 -1-8
7-5 3-13 4-23
5-8 3-10 1-3
5-7 5-7
3-12 4-20
1-7
Preparation for Operation after Storage Preparation for Storage
6-5 4-3, 4-8
6-15 6-14
Radiator Screen Rear Mounted Step Rear Wheels, Dual
R
Rear Wheel Tread Adjustment Restrictor Valve Adjustment
Auxiliary External Valve Internal Valve
Reverse-O -Torc Lubrication Oil Filter Operation
6-13 7-2 7-5
4-23, 4-24, 4-25
4-17 4-18 4-17
3-8 3-8
4-22
8.3
s Safety Instructions Safety Shield and PTO Operation Precautions Seat Adjustment Seat Belt Serial Numbers Single Acting Cylinders
Adjustments and Use Spark Plugs, Servicing Specifications
Belt Pulley Drawbar Electrical Engine Engine Oil Four-Wheel Drive Axle Capacities Four-Wheel Drive Tire Recommendations Fuel Hydraulic Systems Power Steering Power Take-Off Tire Inflation and Load Recommendations Tractor Dimensions Travel Speeds Unit Capacities
Speed-o-Tac Speed -0 -Tac Lubrication Starting Engine Stay Rod Lubrication Steering Gear Lubrication, Manual Steering Knuckle Lubrication Steering Wheel Adjustment Stopping Engine Storage
Fuel Tractor Removal From
Strainer, Fuel Switch
Light Ignition -Starter
T Temperature Gauge. Water Three-Point Hitch
Adjustments
8·4
Control Lever Control Linkage Adjustment Leveling Adjustment Lubrication
3-9,
INDEX
2-1 4-21 4-7 7-5 6-1
4-18 6-9
1-1 1-1 1-4 1-2 1-2 1-6 1-6 1-2 1-3 1-3 1-7 1-5 1-7 1-6 1-8 4-3
3-11
4-7 3-13 3-10 3-12 4-4 4-9
4-5 6-14 6-15
6-3
4-2 4-3
4-2
4-11 4-10
5-8 4-13 3-11
Three-Point Hitch (Continued) Lower Link Adjustment Operation Specifica tions Upper Link Adjustment Width Categories
Timing Ignition Tire Inflation and Load Recommendations Toe-In Adjustment, Front Axle Tractor Break-In Procedure Tractor Engine Operation Transmission and Final Drive Lubrication
Oil Filter Travel Speeds Troubleshooting
Hydraulic Systems Engine Reverse-o -Torc
Upper Backrest
Valves LP Gas
u
v
Clearances, Engine Visible Sight Gauge, LP Gas
Warning Lamp Water Temperature Gauge Weights
Front Frame Wheel
Wheel Bearings, Front Adjustment Lubrication
Wheel Guard Fuel Tank
w
Wheel Guard Fuel Tank Condensation Drain Wheel Tread Adjustment
4-11 4-10, 4-13
1-4 4-13 4-12 5-4 1-5 5-8 4-1 4-9 3-4 3-5 1-6
6-18 6-15 6-20
7-4
4-3 1-2 4-2
7-1 4-2
7-2 7-2
5-6, 5-7 3-13
4-6, 7-3 6-3
Front Rear
Wiring Diagrams
4-22 4-23, 4-24, 4-25
6-10, 6-11
