Operating and installation instructionsGas hobs
To avoid the risk of accidents or damage to the appliance it is essentialto read these instructions before it is installed and used for the first time.
en-GB M.-Nr. 09 168 460
2
This hob can be used in countries other than those specified on the appliance.It is, however, set up for connection to the gas and electricity supplies in thecountries specified. For trouble-free operation of the appliance, it is best to useit in the countries specified for use.For use in other countries, please contact Miele in your country.
Gas-heated appliances
3
Safety precautions to take if you smell gas Turn off the gas emergency control valve immediately.
This is usually located near the gas meter.
Eliminate all sources of ignition in a safe manner.Do not smoke, light cigarette lighters or matches.
Do not operate electrical lights or switches, i.e. do not switch them "On" or"Off".
Open all doors and windows to ventilate the area.
If the smell of gas persists, evacuate the building.
In the UK you must now: Call the Gas Emergency Contact Centre (Tel: 0 800 111 999).
For any gas work in the UK always use a Gas Safe registered engineer.
In other countries please follow relevant country specific procedures on gas.
Contents
4
Warning and Safety instructions .......................................................................... 6
Caring for the environment ................................................................................ 16
Guide to the appliance ........................................................................................ 17Hob........................................................................................................................ 17
KM 3034 ........................................................................................................... 17KM 3054 ........................................................................................................... 18
Control knobs........................................................................................................ 19Burner.................................................................................................................... 20Minute minder controls / indicators....................................................................... 21Accessories supplied ............................................................................................ 22
Using for the first time ........................................................................................ 23Cleaning the hob for the first time......................................................................... 23Switching on the hob for the first time .................................................................. 23
Pans ...................................................................................................................... 24
Tips on saving energy ........................................................................................ 26
Operation.............................................................................................................. 27Rapid ignition system............................................................................................ 27Switching on.......................................................................................................... 27Adjusting the flame................................................................................................ 28Switching off.......................................................................................................... 28Easy switch-off function........................................................................................ 28In operation / residual heat indicators ................................................................... 29
Minute minder...................................................................................................... 30Minute minder ....................................................................................................... 30Setting the minute minder for a cooking zone ...................................................... 30
Safety features..................................................................................................... 31System lock........................................................................................................... 31Flame failure monitor............................................................................................. 31Safety switch-off ................................................................................................... 31
Cleaning and care ............................................................................................... 32Ceramic surface .................................................................................................... 33Pan supports ......................................................................................................... 34Control knobs........................................................................................................ 34Burner.................................................................................................................... 34
What to do if ... .................................................................................................... 36
Contents
5
Optional accessories .......................................................................................... 39
Safety instructions for installation ..................................................................... 40
Safety distances .................................................................................................. 41
Installation notes ................................................................................................. 44
Building-in dimensions ...................................................................................... 45KM 3034 ................................................................................................................ 45KM 3054 ................................................................................................................ 46
Installation............................................................................................................ 47
Electrical connection .......................................................................................... 49
Gas connection.................................................................................................... 51
Burner ratings ...................................................................................................... 53
Converting to another gas type ......................................................................... 54Jet table................................................................................................................. 54Changing the jets .................................................................................................. 54
Changing the main jets..................................................................................... 54Changing the small jets .................................................................................... 55
Functional check ................................................................................................... 56
After sales service, data plate, guarantee ........................................................ 57
Product data sheets ........................................................................................... 58
Warning and Safety instructions
6
This hob complies with all relevant safety requirements. Inappro-priate use can, however, lead to personal injury and damage toproperty.
To avoid the risk of accidents and damage to the hob, please readthese instructions carefully before installation and before using itfor the first time. They contain important notes on installation,safety, use and maintenance.Miele cannot be held liable for damage caused by non-compliancewith these instructions.
Keep these instructions in a safe place and ensure that new usersare familiar with the content. Pass them on to any future owner.
Warning and Safety instructions
7
Correct application
This hob is intended for domestic use and use in other similar en-vironments.
This hob is not intended for outdoor use.
It is intended for domestic use only to cook food and keep itwarm. Any other use is not supported by the manufacturer and couldbe dangerous.
People with reduced physical, sensory or mental capabilities, orlack of experience and knowledge who are not able to use the hobsafely on their own must be supervised whilst using it. They mayonly use it unsupervised if they have been shown how to use it safelyand recognise and understand the consequences of incorrect opera-tion.
Warning and Safety instructions
8
Safety with children
Children under 8 years of age must be kept away from the hobunless they are constantly supervised.
Children 8 years and older may only use the hob unsupervised ifthey have been shown how to use it in a safe way and can recogniseand understand the consequences of incorrect operation.
Children must not be allowed to clean the hob unsupervised.
Please supervise children in the vicinity of the hob and do not letthem play with it.
The hob gets hot when in use and remains hot for a while after be-ing switched off. Keep children well away from the hob until it hascooled down and there is no danger of burning.
Danger of burning.Do not store anything which might arouse a child's interest in stor-age areas above or next to the hob. Otherwise they could be temp-ted into climbing onto the appliance.
Danger of burning or scalding.Place pots and pans on the cooking zone in such a way that childrencannot pull them down and burn themselves.
Danger of suffocation. Packaging, e.g. plastic wrappings, must bekept out of the reach of babies and children. Whilst playing, childrencould become entangled in packaging or pull it over their head andsuffocate.
Activate the system lock to ensure that children cannot switch onthe hob inadvertently.
Warning and Safety instructions
9
Technical safety
Unauthorised installation, maintenance and repairs can causeconsiderable danger for the user. Installation, maintenance and re-pairs must only be carried out by a Miele authorised technician.
Do not use a damaged appliance. It could be dangerous. Checkthe hob for visible signs of damage.
Reliable and safe operation of this hob can only be assured if ithas been connected to the mains electricity supply.
The electrical safety of this hob can only be guaranteed when cor-rectly earthed. It is essential that this standard safety requirement ismet. If in any doubt please have the electrical installation tested by aqualified electrician.
To avoid the risk of damage to the hob, make sure that the con-nection data on the data plate (voltage and frequency) match themains electricity supply before connecting it to the mains. Consult a qualified electrician if in doubt.
Do not connect the hob to the mains electrical supply by a multi-socket adapter or extension lead. These are a fire hazard and do notguarantee the required safety of the appliance.
For safety reasons, this hob may only be used after it has beenbuilt in.
This hob must not be used in a non-stationary location (e.g. on aship).
Never open the casing of the hob.Touching or tampering with electrical connections or componentsand mechanical parts is highly dangerous to the user and can causeoperational faults.
While the hob is under guarantee, repairs should only be under-taken by a Miele authorised service technician. Otherwise the guar-antee is invalidated.
Warning and Safety instructions
10
Miele can only guarantee the safety of the appliance when genu-ine original Miele replacement parts are used. Faulty componentsmust only be replaced by Miele spare parts.
The hob is not intended for use with an external timer switch or aremote control system.
Connection to the gas supply must be carried out by a suitablyqualified gas fitter (e.g. a Gas Safe registered technician in the U.K).
The hob may be connected to the electrical supply by a fused plugand switched socket. If you wish to connect it to a fused spur con-nection, or if the plug has been removed or the connection cable isnot supplied with a plug, the hob must be connected to the mainssupply by a suitably qualified electrician.
If the connection cable is damaged, it must be replaced by a suit-ably qualified electrician with a special connection cable of type H05 VV-F (pvc insulated). See "Electrical connection".
During installation, maintenance and repair work, the hob must bedisconnected from the mains electricity supply. The gas supply mustalso be shut off. Depending on country this is done in one of severaldifferent ways:
– the mains fuse has been disconnected, or
– the screw-out fuse is removed (in countries where this is applic-able), or
– switch off at the wall socket and withdraw the plug from thesocket. Pull by the plug and not by the mains connection cable todisconnect from the mains electricity supply.
– the gas inlet valve is closed.
Warning and Safety instructions
11
Danger of electric shock!Do not use the hob if it is faulty, or if the ceramic surface is cracked,chipped or damaged in any way. If it is in use switch it off immedi-ately. Disconnect it from the mains electricity supply and gas supply,and contact Miele.
If the hob is installed behind a furniture panel (e.g. a door), ensurethat the door is never closed whilst the hob is in use. Heat and mois-ture can build up behind a closed furniture panel and cause sub-sequent damage to the hob, the housing unit and the floor. Do notclose the door until the residual heat indicators have gone out.
Warning and Safety instructions
12
Correct use
The hob gets hot when in use and remains hot for a while after be-ing switched off. There is a danger of burning until the residual heatindicators go out.
Due to the high temperatures radiated, objects left near the hobwhen it is in use could catch fire. Do not use the hob to heat up the room.
Oil and fat can overheat and catch fire. Do not leave the hob unat-tended when cooking with oil and fat. If it does ignite do not attemptto put the flames out with water.Disconnect the hob from the mains and use a suitable fire blanket,saucepan lid, damp towel or similar to smother the flames.
Flames could set the grease filters of a cooker hood on fire. Donot flambé under a cooker hood.
Spray canisters, aerosols and other inflammable substances canignite when heated. Therefore do not store such items or substancesin a drawer under the hob. Cutlery inserts must be heat-resistant.
Do not heat an empty pan.
Do not heat up food in closed containers e.g. tins or sealed jarson the hob, as pressure can build up in the container, causing it toexplode.
Do not cover the hob, e.g. with a hob cover, a cloth or protectivefoil. The material could catch fire, shatter or melt if the hob isswitched on by mistake or if residual heat is still present.
When the hob is switched on either deliberately or by mistake, orwhen there is residual heat present, there is the risk of any metalitems left on the hob heating up, with the danger of burning. De-pending on the material, other items left on the appliance could alsomelt or catch fire. Do not use the hob as a resting place.
Warning and Safety instructions
13
You could burn yourself on the hot hob. Protect your hands withheat-resistant pot holders or gloves when handling hot pots andpans. Do not let them get wet or damp, as this causes heat to trans-fer through the material more quickly with the risk of scalding orburning yourself on steam. Be sure to keep all textiles away from thegas flames. Do not use oversized cloths, tea towels or other similarmaterials.
When using an electrical appliance, e.g. a hand-held food blender,near the hob, ensure that the cable of the electrical appliance cannotcome into contact with the hot hob. The insulation on the cablecould become damaged.
Even a light object can cause damage in certain circumstances.Do not drop anything on the ceramic surface.
Plastic and aluminium foil containers melt at high temperatures.Do not use plastic or aluminium foil containers on the hob.
If a cooker hood is installed above the hob, ensure that the burn-ers are always covered with a pan when in use. Otherwise flamescould reach the cooker hood, parts of which could then be damagedor even set on fire.
Only light the gas burners after all burner parts have been properlyassembled.
Pans must be the correct size for the burner they are used on (see"Suitable Pans"). A pan which is too small will be unstable on thepan support. If the pan diameter is too large, flames can spread outto the sides and damage or burn the worktop, wall claddings or sur-rounding units and also parts of the hob. Miele cannot be held liablefor this type of damage.
Ensure that the flames from the burner do not spread out beyondthe base and up the sides of the pan.
Warning and Safety instructions
14
Do not use pans with very thin bases on this hob, and never heatup empty pans as they could get damaged. This could also damagethe appliance.
The pan support supplied with the appliance must always beused. Never place a pan on the burner itself.
Replace the pan supports carefully to avoid scratching the surfaceof the hob.
Do not use or store flammable materials near this hob.
Remove splashes of fat and other food debris from the surface ofthe hob as soon as possible. These are a fire hazard.
Using the hob will cause a build-up of heat and moisture in theroom in which it is installed. Ensure that the room has sufficient nat-ural or mechanical means of ventilation, e.g. a cooker hood.
If the hob is used for very long periods of time, additional ventila-tion of the room may be necessary, e.g. by opening windows ordoors, or running the cooker hood on the highest setting.
Do not use roasting dishes, pans or grilling stones that are largeenough to cover more than one burner. The resulting build-up ofheat could damage the hob.
If the hob has not been used for a long period of time it should bethoroughly cleaned before it is used again. It is also advisable tohave the appliance tested by a qualified person for safety.
Warning and Safety instructions
15
Cleaning and care
Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short cir-cuit.
Caring for the environment
16
Disposal of the packing mater-ialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.
Recycling the packaging reduces theuse of raw materials in the manufactur-ing process and also reduces theamount of waste in landfill sites.
Disposing of your old appli-anceElectrical and electronic appliances of-ten contain valuable materials. Theyalso contain specific materials, com-pounds and components, which wereessential for their correct function andsafety. These could be hazardous to hu-man health and to the environment ifdisposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.
Please dispose of it at your local com-munity waste collection / recyclingcentre for electrical and electronic ap-pliances, or contact your dealer orMiele for advice. You are also respons-ible (by law, depending on country) fordeleting any personal data that may bestored on the appliance being disposedof. Please ensure that your old appli-ance poses no risk to children while be-ing stored prior to disposal.
Guide to the appliance
17
Hob
KM 3034
a Large burner
b Small burner
c Wok burner
d Medium burner
e Medium burner
f Pan support (one for each burner)
g In-operation/Residual heat indicators
h Minute minder
i Easy switch-off function
j Cooking zone symbol
Control knobs for the cooking zones
k Front right
l Rear right
m Middle
n Rear left
o Front left
Guide to the appliance
18
KM 3054
a Wok burner
b Large burner
c Small burner
d Medium burner
e Medium burner
f Pan support (one for each burner)
l Cooking zone symbols
m In-operation/Residual heat indicators
n Minute minder controls / indicators
o Easy switch-off function
Control knobs for the cooking zones
g Front right
h Rear right
i Rear middle
j Front middle
k Left
Guide to the appliance
19
Control knobs
Small/Medium/Large burners
Symbol Description
Burner off, the gas supply is turned off
Largest flame
Smallest flame
Wok burner
Symbol Description
Burner off, the gas supply is turned off
Largest flame: inner and outer burner on highest setting.
Large flame: outer burner on lowest setting, inner burner on highestsetting.
Small flame: outer burner off, inner burner on highest setting.
Smallest flame: outer burner off, inner burner on lowest setting.
Guide to the appliance
20
Burner
Wok burner
a Outer burner cap
b Inner burner cap
c Burner head
d Burner base
e Thermocouple
f Ignitor
Small, medium and large burners
a Burner cap
b Burner head
c Burner base
d Thermocouple
e Ignitor
Guide to the appliance
21
Minute minder controls / indicators
a Activating the safety lock / Setting the time
b Minute minder- For switching on/off- Switching between functions- For selecting a cooking zone
Indicator lights
c Minute minder
d Indicator light for relevant zone, e.g. the rear right cooking zone
f Indicator light for half hours if the minute minder setting exceeds 99 minutes
e Time display
to Duration in minutes. to . Duration in hours
Guide to the appliance
22
Accessories suppliedThe accessories supplied with your ap-pliance as well as a range of optionalones are available to order from Miele(see "Optional accessories").
Wok ring
The wok ring supplied gives additionalstability to the wok, especially to wokswith a rounded base.
Combination trivet
The combination trivet supplied mustbe used if you are using pans with asmaller base diameter than that spe-cified in the chart for suitable pans.
Using for the first time
23
Please stick the extra data plate forthe appliance supplied with this doc-umentation in the space provided inthe "After sales service, data plate,guarantee" section of this booklet.
Remove any protective wrapping andstickers.
Cleaning the hob for the firsttime Before using for the first time, clean
the hob with a damp cloth only andthen wipe dry.
Clean all removable parts of the burn-ers with a solution of warm water anda small amount of washing-up liquidapplied with a soft sponge. Dry allparts thoroughly after cleaning andthen reassemble the burners (see"Cleaning and care").
Switching on the hob for thefirst timeThe metal components have a protect-ive coating which when heated for thefirst time will give off a slight smell andpossibly some vapours.
The smell and any vapours given off donot indicate a faulty connection or ap-pliance and they are not hazardous tohealth.
Pans
24
Minimum pan base diameter
Burner Ø cm
Small burner 10
Medium burner 12
Large burner 14
Wok burner 14
Maximum diameter at top of pan
Burner Ø cm
Small burner 20
Medium burner 22
Large burner 24
Wok burner 26
– Select cookware that fits the size ofthe burner:Large diameter = large burnerSmall diameter = small burner.
– Refer to the chart above and ensurethat the pan diameter falls within theminimum and maximum diametersgiven for the burner you are using. Ifthe pan diameter is too large, flamescan spread out to the sides and dam-age or burn the worktop, wall clad-dings or surrounding units and alsoparts of the hob or other appliances. Pans which are too small for the pansupports, or pans which do not sitsecurely on the pan supports, aredangerous and should not be used.
– Unlike pans that are used on an elec-tric hob, the bottom of pans used ona gas hob do not have to be flat todeliver good cooking results.
– Remember when purchasing newpans that manufacturers usually referto the diameter at the top of the panin their documentation, and not to thebase diameter.
– Any heat-resistant pans can be usedon a gas burner.
– Pans with thick bases are preferableas these distribute heat more evenly.With thin bases, there is a danger offood overheating in places. Stir thefood frequently.
– Always place cookware on the pansupport supplied with the appliance.Never place it directly on the burner.
– Position the cookware centrally onthe pan support so that it sits se-curely and cannot tip. A little move-ment is quite normal and not a causefor concern.
– Do not use pots or pans that havebases with pronounced edges.
Pans
25
Wok ring Use the wok ring supplied to give ad-
ditional stability to pans, especially towoks with a rounded base.
Place the wok ring on the pan sup-port so that it sits securely in positionand cannot move (see diagram).
The wok is unique among cookware inthat it has a small base diameter and alarge rim diameter (usually 35-40 cm).Wok pans are ideal for use on the wokburner.
Combination trivetThe combination trivet must be used ifyou wish to use a pan with a smallerdiameter base than the minimum givenin the table.
Tips on saving energy
26
– Use a pan lid whenever possible tominimize heat loss.
– Wide, shallow pans are preferable totall, narrow ones. They will heat upfaster.
– Cook with as little water as possible.
– Reduce the size of the flame once thewater has come to the boil or the oilis hot enough to fry in.
– Use a pressure cooker to reducecooking times.
Operation
27
Rapid ignition systemThe appliance is supplied with a rapidignition system with the following fea-tures:
– Rapid ignition without pressing andholding the control,
– Automatic re-ignitionShould the flame be extinguished bya gust of air, the burner will re-igniteautomatically. If re-ignition is unsuc-cessful, the gas supply will be cut offautomatically (see "Flame failuremonitor").
Switching on
Fire hazard.Do not leave the appliance unatten-ded whilst it is being used.
The control knob for the burner mustbe pressed in and turned anti-clock-wise to the large flame symbol toswitch on. The ignitor will "click" andignite the gas.
When a control knob is activated, aspark is developed automatically on allburners. This is normal and does notindicate a defect.
If the burner fails to ignite, turn thecontrol knob to the "" position. Airthe room or wait at least 1 minute be-fore trying again.
If the burner does not ignite thesecond time, turn the control knobback to "" and see "What to doif ...".
You might hear the burner re-ignitingas it switches itself back on(1-2 clicks), for instance, in the eventof a draft.
Operation
28
Adjusting the flameThe burners can be regulated at anylevel between the strongest and weak-est flame.
As the outer part of the flame is muchhotter than the centre, the tips of theflames should stay beneath the panbase. Flame tips which extend beyondthe sides of the pan merely warm upthe air in the room and can also dam-age pan handles and increase thedanger of injury.
Adjust the flame so that it does notspread out beyond the sides of thepan.
Wok burner
Depending on the type of control knob,there may be a stopper between thelow and high settings at the 6 o'clockposition.
Press the control knob down lightly tomove past this resistance.
Switching off Turn the control clockwise to position
"".
This stops the flow of gas and the flamegoes out.
Easy switch-off function
Touching the sensor switches off allactive burners.
Touch the sensor.
All burners are switched off. The in-op-eration/residual heat indicators of theswitched off burners flash and the in-dicator light for the easy switch-offfunction remains illuminated.If a minute minder has been set for acooking zone, it will be cancelled.
Turn the control to "".
The easy switch-off indicator light goesout and the in-operation/residual heatindicators of cooking zones which arestill hot will light up constantly.
Operation
29
In operation / residual heat in-dicatorsThe in-operation / residual indicatorlights up when a gas burner is switchedon. The in-operation indicator will goout when the burner is switched off.The residual heat indicator will remainon until the gas burner is cool enoughto touch.
If the indicator lights are flashing, thereis a fault. See "Problem solvingguide".
Danger of burning. Do not touchthe pan supports, cooking zones orthe hob whilst the residual heat in-dicators are lit up.
Minute minder
30
A duration of between 1 minute ()and 6 hours (.) can be set.
Use the - sensor to reduce the timefrom . to , and the + sensor to in-crease the time from to .. The dis-play stops at . and at . To continuebeyond this setting, briefly remove yourfinger from the sensor and then touch itagain.Durations exceeding 99 minutes are setin half-hour steps. The half hour is in-dicated by a dot after the number.
Minute minder
Setting
Touch the sensor.
and the minute minder indicatorlamp will flash in the timer display.
Select the time you want with the - or+ sensor.
Changing
Touch the sensor.
Select the time you want with the - or+ sensor.
Deleting
Touch the sensor.
Touch the - and + sensors at thesame time until appears in thetimer display.
Setting the minute minder for acooking zoneA minute minder can be allocated forany switched on cooking zone. Thisfunction can be used simultaneously forall cooking zones.
Switch on the required cooking zone.
Keep touching the sensor until theindicator light for this cooking zonestarts flashing.
If several cooking zones are switchedon, the indicator lights for the cookingzones being used light up anti-clock-wise, starting with the front right.
Set the time you want.
If you want to set another cookingzone to switch off automatically, fol-low the same steps as describedabove.
If more than one switch-off time isprogrammed, the shortest time re-maining will be displayed, and the cor-responding indicator light will flash.The other indicator lights will light upconstantly.
If you want to show the time remain-ing for another zone which is count-ing down in the background, touchthe sensor repeatedly until the in-dicator light for the zone you requireflashes.
Safety features
31
System lock
The system lock is deactivated ifthere is an interruption to the powersupply.
The system lock can only be activatedif all the cooking zones are switchedoff.
The hob is fitted with a system lock sothat it cannot be used by mistake.When activated the cooking zones can-not be switched on and the minuteminder cannot be used.
If a control knob is turned or a sensor istouched when the system lock is active,the indicator light illuminates and ap-pears in the minute minder display.
Activating
Touch the + and - sensors at thesame time until appears in theminute minder display and a tonesounds.
will go out after a short while.
Deactivating
Touch the + and - sensors at thesame time until goes out in theminute minder display and a tonesounds.
Flame failure monitorThis hob has a flame failure monitor. Ifthe flame goes out, for example be-cause food has boiled over or there hasbeen a sudden draught, and automaticre-ignition has been unsuccessful, thesupply of gas to the burner will be cutoff. This will prevent any gas escaping.To use the burner again, turn the controlknob to "".
Safety switch-offIf the burner has been used for an un-usually long period of time, it will switchitself off automatically. To use theburner again, turn the control to the ""position.
Cleaning and care
32
Danger of burning.The burners must be switched off.The hob needs to cool down.
Danger of injury.The steam from a steam cleaning ap-pliance could reach electrical com-ponents and cause a short circuit.Do not use a steam cleaner to cleanthe hob.
The use of unsuitable cleaningagents can cause the surfaces todiscolour or alter.All surfaces are susceptible toscratching.Remove any residual cleaning agentimmediately.
Unsuitable cleaning agentsTo avoid damaging the surfaces of yourappliance, do not use:
– cleaning agents containing soda, al-kalines, ammonia, acids or chlorides
– cleaning agents containing descalingagents
– stain or rust removers
– abrasive cleaning agents, e.g.powder cleaners and cream cleaners
– solvent-based cleaning agents
– dishwasher cleaner
– grill and oven cleaners
– glass cleaning agents
– hard, abrasive brushes or sponges,e.g. pot scourers, brushes orsponges which have been previouslyused with abrasive cleaning agents
– melamine eraser blocks
Cleaning and care
33
The surfaces of the burner compon-ents and pan supports will becomemore matt with time. This is com-pletely normal and does not indicatedamage to the material.
The entire hob should be cleanedafter each use.
Stubborn soiling should be soakedfirst.
Dry the hob after using water to cleanit. This helps prevent limescale de-posits.
Tip: Food that has boiled over onto ahot hob can result in discolouration onthe burner components. Immediatelyremove all spilled food and all salt orsugar splatters.
Ceramic surface
Do not clean the area between theglass-ceramic surface and the frameor the frame and the worktop withsharp, pointed objects.This could damage the seals.
Do not use washing-up liquid toclean the appliance as washing-up li-quid will not remove all soiling anddeposits.It will form an invisible coating whichwill cause permanent discolourationof the ceramic surface.Clean the ceramic surface regularlywith a suitable ceramic cleaningagent such as the Miele ceramic andstainless steel hob cleaner.
Wipe all coarse soiling off using adamp cloth. Stubborn soiling mayneed to be removed with a shieldedscraper blade.
Then clean the hob with Mieleceramic and stainless steel hobcleaner (see "Optional accessories")or a suitable proprietary ceramic hobcleaning agent applied with kitchenpaper or a clean cloth. Do not applycleaning agent whilst the hob is stillhot, as this could result in marking.Please follow the manufacturer's in-structions.
Wipe the surface afterwards with adamp cloth to remove any cleaningagent residues.
Residues can burn onto the appliancethe next time it is used and causedamage to the ceramic surface. En-sure that all cleaning agent residuesare removed.
Finally, dry the ceramic surface with aclean soft cloth.
Any marks left by limescale residue orwater can be removed using the Mieleceramic and stainless steel hob cleaner.
Cleaning and care
34
Pan supports Remove the pan supports.
Clean the pan supports in the dish-washer or with a solution of warmwater and a little washing-up liquidapplied with a soft sponge. Stubbornsoiling should be soaked first.
After cleaning, dry the pan supportsthoroughly with a clean cloth.
Control knobs
The control knobs are not dish-washer safe.The control knobs should only becleaned by hand.
The control knobs may become dis-coloured if they are not cleaned regu-larly.
Clean the control knobs using a solu-tion of warm water and a little wash-ing-up liquid applied with a softsponge.
Burner
Do not clean any parts of the burnerin a dishwasher.
The burner should be dismantled andthen cleaned by hand using a solu-tion of warm water and a little wash-ing-up liquid applied with a softsponge.
Parts of the burner that cannot be re-moved should be wiped clean with adamp cloth only.
The ignitor and thermocouple shouldbe very carefully wiped clean using awell wrung out cloth.
Do not let the ignitor get wet. If it getswet, it will not spark.
After cleaning, dry all surfaces with aclean cloth. Make sure that the flameslits are clean and completely dry.
The surfaces of the burner caps willbecome more matt with time. This isquite normal and does not indicatedamage to the burner caps. Nor willaffect the operation of the hob.
Cleaning and care
35
Assembling the small, medium andlarge burners
Place the burner head on theburner base so that the thermo-couple and the ignitor extendthrough their respective holes in theburner head. The burner head mustclick into place correctly.
Place the burner cap flat over theburner head . When correctly posi-tioned, the burner cap will not slideabout.
Ensure parts are reassembled in thecorrect order.
Assembling the wok burner
Place the burner head on theburner base so that the thermo-couple and the ignitor extendthrough their respective holes in theburner head. The burner head mustclick into place correctly.
Then place the burner caps and in position.
Ensure parts are reassembled in thecorrect order.
What to do if ...
36
With the aid of the following guide, minor problems can be easily correctedwithout contacting Miele.If having followed the suggestions below, you still cannot resolve the problem,please contact Miele (see end of this booklet for contact details).
Danger of injury. Installation, maintenance and repairs to electrical appli-ances must only be carried out by a suitably qualified and competent person instrict accordance with current local and national safety regulations.Do not open the casing of the appliance.Repairs and other work by unqualified persons could be dangerous and Mielecannot be held liable for unauthorised work.
Problem Cause and remedy
The burners do not ig-nite when the hob is be-ing used for the firsttime or after it has beenout of use for a longerperiod.
There could be air lock in the gas pipe. You may need to make several attempts before the
burner ignites successfully.
The burner does not ig-nite after several at-tempts.
There may be a technical fault. Turn all of the controls clockwise to "" and inter-
rupt the power supply to the hob for a fewseconds.
The burner is not correctly assembled. Assemble the burner correctly.
The gas shut-off valve is closed. Open the gas shut-off valve.
The burner is wet and/or dirty. Clean and dry the burner.
The flame slits are blocked and/or wet. Clean and dry the flame slits.
The gas flame goes outafter being lit.
The flames do not touch the thermocouple and theburner does not get hot enough:The burner parts are not positioned correctly. Position the burner parts correctly.
There is soiling on the thermocouple. Remove any soiling.
What to do if ...
37
Problem Cause and remedy
The flame suddenlylooks different.
The burner parts are not positioned correctly. Position the burner parts correctly.
The burner head or the holes in the burner cap aredirty. Remove any soiling.
The gas flame goes outduring use.
The burner parts are not positioned correctly. Position the burner parts correctly.
There has been a power outage. Turn the control knob in a clockwise direction to
"". Once power has been restored the hob can beused again as normal.
The ignitor on theburner does not spark.
The mains fuse has tripped. You may need to contact a qualified electrician or
Miele.There is food residue stuck between the ignitor andthe burner cap.There is food residue on the thermocouple. Remove any soiling (See "Cleaning and care").
The in-operation / resid-ual heat indicator isflashing.
There has been a power outage. Turn the control knob in a clockwise direction to
"". Once power has been restored the hob can beused as normal again.
What to do if ...
38
Problem Cause and remedy
Letters appear in theminute minder display.
The system lock has been activated. You need to deactivate the system lock (see "Sys-
tem lock").A sensor fault has occurred. Make sure that there is no direct light (from the sun
or from an artificial source) falling onto the hob.The area surrounding the hob must not be toodark.
Make sure that there is nothing covering thesensors or the hob. Take any pans off the hob andwipe away any food deposits.
Interrupt the power supply to the hob for approx. 1minute.
If the problem persists after power has been re-stored, please contact Miele Service.
The in-operation/resid-ual heat indicators areflashing and a combina-tion of letters and num-bers appears in theminute minder display.
The overheating protection mechanism has been ac-tivated. Turn all the control knobs clockwise to "". You
can operate the cooking zones again once hasdisappeared.
There is a fault with the electronics. Reset: touch the easy switch-off function sensor
for three seconds. If this fault code continues to appear in the dis-
play, contact Miele Service.All other fault codesThere is a fault with the electronics. Interrupt the power supply to the hob for approx. 1
minute. If the problem persists after power has been re-
stored, please contact Miele Service.
Optional accessories
39
Miele offer a comprehensive range ofuseful accessories as well as cleaningand conditioning products for yourMiele appliances.
These products can be ordered throughthe Miele Webshop.
These can also be ordered from Miele(see end of this booklet for contact de-tails) or from your Miele dealer.
Ceramic and stainless steelhob cleaner 250 ml
Removes heavy soiling, limescale de-posits and aluminium residues
Microfibre cloth
Removes finger marks and light soiling
Safety instructions for installation
40
Fit the wall units and cooker hood before fitting the hob to avoid damaging thehob.
The veneer or laminate coatings of worktops (or adjacent kitchenunits) must be treated with 100 °C heat-resistant adhesive which willnot dissolve or distort. Any backmoulds must be of heat-resistantmaterial.
The hob must not be installed over a fridge, fridge-freezer, freezer,dishwasher, washing machine, washer-dryer or tumble dryer.
A gas hob must not be installed directly next to a deep fat fryer asthe gas flames could ignite the fat in the fryer. It is essential to main-tain a distance of at least 300 mm between these two appliances.
When installing the hob, make sure that the gas pipe and elec-trical connection cable cannot come into contact with hot applianceparts.
The electrical cable and any flexible gas connection pipes must beinstalled in such a way so that they do not come into contact withany moving kitchen parts (e.g. a drawer), and cannot becometrapped.
Observe carefully the safety clearances listed on the followingpages.All dimensions are given in mm.
Safety distances
41
Safety distance above the hob
A minimum safety distance must bemaintained between the appliance andthe cooker hood above it. See thecooker hood manufacturer's operatingand installation instructions for details.If the manufacturer's instructions arenot available for the cooker hood or ifany flammable objects (e.g. utensil rails,wall units etc) are installed above thehob a minimum safety distance of atleast 760 mm must be maintainedbetween them and the appliance below.
When two or more appliances whichhave different safety distances areinstalled together below a cookerhood, you should observe thegreatest safety distance.
Safety distances
42
Safety distances to the sidesand back of the hobIdeally the hob should be installed withplenty of space on either side. Theremay be a wall at the rear or a tall unit orwall on one side (right or left) (see illus-trations).
Minimum distance between the backof the worktop cut-out and the rearedge of the worktop:50 mm
Minimum distance between theworktop cut-out and a wall or tall unit tothe right of it:150 mm.
Minimum distance between theworktop cut-out and a wall or tall unit tothe left of it:150 mm.
Not allowed
Recommended
Not recommended
Not recommended
Safety distances
43
Safety distance when installing the appliance near a wall withadditional niche claddingA minimum safety distance must be maintained between the worktop cut-out andany niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e.g. wood) a minimumsafety distance of 50 mm must be maintained between the cut-out and thecladding.
If the niche cladding is made from a non-combustible material (e.g. metal, naturalstone, ceramic tiles) the minimum safety distance between the cut-out and thecladding will be 50 mm less the thickness of the cladding.Example: 15 mm niche cladding 50 mm - 15 mm = minimum safety distance of 35 mm
Flush-fitted hobs Hob with frame or bevelled edge
a Masonry
b Niche cladding dimension x = thickness of the niche cladding material
c Worktop
d Worktop cut-out
e Minimum distance to combustible materials 50 mmnon-combustible materials 50 mm - dimension x
Installation notes
44
Seal between the hob and theworktop
Do not use sealant between the hoband the worktop. This could result indamage to the hob or the worktop ifthe hob ever needs to be removedfor servicing.The sealing strip under the edge ofthe top part of the applianceprovides a sufficient seal for theworktop.
Tiled worktop
Grout lines and the hatched area un-derneath the hob frame must besmooth and even. If they are not thehob will not sit flush with the worktopand the sealing strip underneath thehob will not provide a good sealbetween the hob and the worktop.
Building-in dimensions
45
KM 3034
a Front
b Casing depth
c Mains connection box with mains connection cable, L = 2000 mm
d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
Building-in dimensions
46
KM 3054
a Front
b Casing depth
c Mains connection box with mains connection cable, L = 2000 mm
d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
Installation
47
Preparing the worktop Make the worktop cut-out as shown
in the building-in diagram. Observethe safety distances (see "Safety dis-tances").
Seal the cut surfaces with a suitablesealant to avoid swelling caused bymoisture. The sealant must be heat-resistant.
Make sure that the sealant does notcome into contact with the top of theworktop.
The seal underneath the hob will holdit securely in the cut-out. Any gapbetween the frame and worktop willreduce with time.
Installing the hob Feed the mains connection cable
down through the cut-out.
Place the hob centrally in the cut-out.When doing this, make sure that theseal under the hob sits flush with theworktop on all sides. This is import-ant to ensure an effective seal allround.
If the seal does not meet the worktopcorrectly on the corners, the corner ra-dius (≤ R4) can be carefully scribed tosuit.
Do not use sealant (e.g. silicone).
Connect the hob to the mains.
Connect the hob to the gas supply(see "Gas connection").
Installation
48
Securing the hob
Secure the hob using the brackets supplied.
Functional check After installing the hob, ignite all
burners to check that they are operat-ing correctly:
– The flame must not go out on thelowest setting, or when the control isturned quickly from the highest to thelowest setting.
– On the highest setting, the flamemust have a distinctive and visiblecore.
Electrical connection
49
All electrical work must be carried outby a suitably qualified and competentperson in strict accordance with currentlocal and national safety regulations (BS7671 in the UK). Connection must bemade via a switched socket. This willmake it easier for service techniciansshould the appliance need to be re-paired. The electrical socket must beeasily accessible after installation.
Danger of injury.Miele cannot be held liable for unau-thorised installation, maintenanceand repair work as this can be dan-gerous to users. Miele cannot be held liable for dam-age or injury caused by incorrect in-stallation, maintenance or repairwork, or by an inadequate or faultyearthing system (e.g. electric shock).If the plug is removed from the con-nection cable or if the cable is sup-plied without a plug, the appliancemust be connected to the electricalsupply by a suitably qualified electri-cian.If the switched socket is not access-ible after installation, or if the appli-ance is to be hard-wired, an addi-tional means of disconnection mustbe provided for all poles. Whenswitched off, there must be an all-pole contact gap of at least 3 mm inthe switch (including switch, fusesand relays). Connection data isshown on the data plate. It mustmatch the mains electrical supply.After installation ensure that all elec-trical components are shielded andcannot be accessed by users.
Total power ratingSee data plate
ConnectionAC 230 V, 50 Hz
The connection data is quoted on thedataplate. It must match the householdsupply.
Residual current deviceFor extra safety, it is advisable to pro-tect the appliance with a suitable resid-ual current device (RCD) with a triprange of 30 mA.
WARNING THIS APPLIANCE MUST BEEARTHED
Electrical connection
50
Disconnecting from the mains
Danger of electric shock.After disconnection, ensure the ap-pliance cannot be switched back onby mistake.
To disconnect the appliance from themains power supply, do one of the fol-lowing depending on installation:
Safety fuses
Completely remove fuses
Automatic circuit breakers
Press the (red) button until the middle(black) button springs out.
Built-in circuit breakers
Circuit breakers, type B or C: switchthe on-off switch from 1 (on) to 0 (off).
Residual current device (RCD)
Switch the main switch from 1 (on) to0 (off) or press the test button.
Replacing the mains cable
Danger of electric shock.The mains connection cable must bereplaced by a suitably qualified andcompetent person in accordancewith current local and national safetyregulations. (e.g. BS 7671 in the UK).
If the mains cable needs to be replacedit must be replaced with a special con-nection cable, type H 05 VV-F (PVC-in-sulated), available from Miele.
The connection data is quoted on thedata plate.
Gas connection
51
For any gas work in the UK alwaysuse a Gas Safe registered engineer.
Connection to the gas supply, orconversion to a different gas type,may only be undertaken by an ap-proved and registered gas installer.The installer is responsible for ensur-ing that the appliance functions cor-rectly when installed.
The gas connection must be in-stalled so that connection can bemade either from inside or outsidethe kitchen unit. The isolating valvemust be easily accessible and visible(by opening the kitchen door if ne-cessary).
Check with your local gas supplierabout the type of gas its calorificvalue and compare this informationwith the type of gas quoted on theappliance's data plate.
This hob is not connected to an ex-haust flue.When installing and connecting theappliance please observe all relevantinstallation instructions and ensure ithas adequate ventilation once in-stalled.
Connection to the gas supply mustbe carried out in strict accordancewith local and national safety regula-tions (e.g. Gas Safe in the UK). Everyappliance should have its own easilyaccessible isolating valve and testpoint.
Any special local conditions relatingto gas installations as well as build-ing regulations must also be ob-served.
Gas connections, pipes and connec-tion cables can suffer damage if ex-posed to heat from the hob.After installation make sure thatneither the gas pipe nor the mainscable can come into contact with hotparts of the appliance and that thegas pipe and connections on the hobcannot come into contact with hotgas exhaust.
Flexible gas pipes (in countrieswhere permitted) can be damagedby incorrect routing.Attach flexible gas pipes in such away so that they do not come intocontact with any moving kitchenparts (e.g. a drawer) and are not ex-posed to mechanical stress.
The hob must be set for local gasconditions and the gas connectionmust undergo a leakage test.
Gas connection
52
This hob is a class 3 appliance and issuitable for use with natural gas or li-quid gas.
Category in acc. with EN 30
United Kingdom
GB II 2 H3 +20 mbar, 28-30/37 mbar
Ireland
IE II 2 H 3+20 mbar, 28-30/37 mbar
Depending on country of destinationthis appliance is set up for connectionto natural or liquid gas. See adhesive la-bel on the appliance.
Depending on country, a set of jets forconversion to an alternative type of gasmay be included with the hob. Pleasecontact your supplier or Miele for theappropriate conversion jets if neces-sary. Conversion to another type of gasis described under "Conversion to an-other type of gas".
Connecting the hobThe hob is supplied with a conical ¹/₂"gas connection point for connection toone of the following:
– Rigid connection with isolation valve
– Flexible connection in accordancewith DIN 3383 Part 1, maximumlength 2000 mm. (Not for the UK!)
Unsuitable sealants may not be leak-proof.Connections must be sealed usingappropriate sealant.
a Connection with test point specific-ally for GB
b 90° bendConnection with test point specific-ally for GB and 90 ° bend.
Burner ratings
53
Nominal ratings
Burner Gas type Highest setting Lowest set-ting
kW g/h kW
Small burner Natural gas HLiquid gas
1.00.95
–69
0.250.2
Mediumburner
Natural gas HLiquid gas
1.71.7
–124
0.30.35
Large burner Natural gas HLiquid gas
2.72.55
–186
0.50.6
Wok Natural gas HLiquid gas
4.74.6
–335
0.30.25
Total Natural gas HLiquid gas
11.811.5
–837
Converting to another gas type
54
Conversion from one type of gasto another, should only be under-taken by an approved and registeredgas installer in strict accordance withcurrent local and national safety andbuilding regulations.Disconnect the hob from the electri-city supply and turn off the gas sup-ply.
When converting to another type ofgas, both the main and small jetsneed to be changed.
Jet tableThe jet markings refer to a ¹/₁₀₀ mmbore diameter.
Main jet Small jet
Natural gas H
Small burnerMedium burnerLarge burnerWok burner
0.760.941.20
2x 1.07 / 0.72
0.390.420.540.42
Liquid gas
Small burnerMedium burnerLarge burnerWok burner
0.520.660.81
2x 0.70 / 0.46
0.230.360.420.25
Changing the jets Disconnect the hob from the electri-
city supply and turn off the gas sup-ply.
Changing the main jets
Small, medium and large burners
Remove the pan support, burnercap and burner head .
Using an M7 socket spanner, un-screw the main jet
Fit the correct jets securely (see jettable).
Secure the jets against inadvertentloosening with sealing wax.
Converting to another gas type
55
Wok burner
Remove burner caps and burnerhead .
Using an M7 socket spanner, un-screw the main jets .
Fit the correct jets securely (see jettable).
Secure the jets against inadvertentloosening with sealing wax.
Changing the small jets
To change the small jets, the burnerfixing screws must first be loosenedand the upper section of the applianceremoved.
Pull the control knobs off.
Remove the burner components.
Lift the top of the appliance off (see il-lustration).
Using a small screwdriver, unscrewthe small jet in the gas fitting.
Pull out the jet with a pair of pliers.
Fit the correct jets securely (see jettable).
Secure the jets against inadvertentloosening with sealing wax.
Converting to another gas type
56
Functional check Check all gas fittings for leaks.
Reassemble the hob.
Ignite all burners to check that theyare operating correctly.
– The flame must not go out on thelowest setting, or when the control isturned quickly from the highest to thelowest setting.
– On the highest setting, the flamemust have a distinctive and visiblecore.
Adhere the label supplied with thejets, stating the type of gas beingused.
After sales service, data plate, guarantee
57
After sales serviceIn the event of any faults which you cannot easily remedy, please contact
– your Miele Dealer, or
– Miele Service.
See end of this booklet for contact details.
Please note that telephone calls may be monitored and recorded for training pur-poses.
N.B. A call-out charge will be applied to service visits where the problem couldhave been resolved as described in these instructions.
When contacting your Dealer or Miele, please quote the model and serial numberof your appliance.
Data plateSpace in which to stick the extra data plate supplied with the appliance. Ensurethat the model number is the same as the one on the back page of these instruc-tions.
Guarantee: UKThe appliance is guaranteed for 2 years from the date of purchase.
In the UK, you must activate your cover by calling 0330 160 6640 or registeringonline at www.miele.co.uk.
Guarantee: Other countriesFor information on the appliance guarantee specific to your country please contactMiele. See end of this booklet for contact details.
Product data sheets
58
The following data sheets apply to the models described in this operating instruc-tion manual.
Information for domestic gas-fired hobsIn acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier KM 3034
Number of gas burners 5
Energy efficiency per gas burner (EEgas burner) 1. = 58,2 3. = 52,4 4. = 55,1 5. = 55,1
Energy efficiency for the gas hob calculated per kg(EEgas hob)
55,2
Information for domestic gas-fired hobsIn acc. with regulation (EU) No. 66/2014
MIELE
Model name / identifier KM 3054
Number of gas burners 5
Energy efficiency per gas burner (EEgas burner) 1. = 52,4 3. = 55,1 4. = 55,1 5. = 58,2
Energy efficiency for the gas hob calculated per kg(EEgas hob)
55,2
United KingdomMiele Co. Ltd.Fairacres, Marcham RoadAbingdon, Oxon, OX14 1TWCustomer Contact Centre Tel: 0330 160 6600E-mail: [email protected]: www.miele.co.uk
AustraliaMiele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 3981 Gilbert Park Drive, Knoxfield, VIC 3180Tel: 1300 464 353Internet: www.miele.com.au
Miele (Shanghai) Trading Ltd.1-3 Floor, No. 82 Shi Men Yi RoadJing' an District200040 Shanghai, PRCTel: +86 21 6157 3500, Fax: +86 21 6157 3511E-mail: [email protected], Internet: www.miele.cn
China
41/F - 4101, Manhattan Place23 Wang Tai RoadKowloon Bay, Hong KongTel: (852) 2610 1025, Fax: (852) 3579 1404Email: [email protected]: www.miele.hk
Miele (Hong Kong) Limited
Miele India Pvt. Ltd.Ground Floor, Copia Corporate SuitesPlot No. 9, Jasola, New Delhi - 110025Tel: 011-46 900 000, Fax: 011-46 900 001E-mail: [email protected], Internet: www.miele.in
India
Miele Ireland Ltd.2024 Bianconi AvenueCitywest Business Campus, Dublin 24Tel: (01) 461 07 10, Fax: (01) 461 07 97E-Mail: [email protected], Internet: www.miele.ie
Ireland
MalaysiaMiele Sdn BhdSuite 12-2, Level 12Menara Sapura Kencana PetroleumSolaris Dutamas No. 1, Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768
Miele New Zealand LimitedIRD 98 463 631Level 2, 10 College HillFreemans Bay, Auckland 1011, NZTel: 0800 464 353Internet: www.miele.co.nz
New Zealand
Miele Pte. Ltd.163 Penang Road# 04 - 03 Winsland House IISingapore 238463Tel: +65 6735 1191, Fax: +65 6735 1161E-Mail: [email protected]: www.miele.sg
Singapore
Miele (Pty) Ltd63 Peter Place, Bryanston 2194P.O. Box 69434, Bryanston 2021Tel: (011) 875 9000, Fax: (011) 875 9035E-mail: [email protected]: www.miele.co.za
South Africa
Miele Appliances Ltd.Gold & Diamond ParkOffice No. 217-6, Sheikh Zayed RoadP.O. Box 11 47 82 - DubaiTel. +971 4 3044 999Fax. +971 4 3418 852800-MIELE (64353)E-Mail: [email protected]: www.miele.ae
United Arab Emirates
Carl-Miele-Straße 29, 33332 Gütersloh, GermanyManufacturer: Miele & Cie. KG
M.-Nr. 09 168 460 / 04en-GB
KM 3034 / KM 3054
