OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC- B12 STANDARD WHITE FINISH- PANEL CUTOUTS FOR BOOMS DONE IN FIELD BY OTHERS- RECOMMENDED INLET SIZE AND LOCATION SHOWN- THE CEILING IS FACTORY PREMANUFACTURED TO SIZES AND TOLERANCE +/- .032"- SITE ADJUSTMENTS TO PERIMETER SOFFITS AND/OR DRYWALL MAY BE REQUIRED
AND ARE THE RESPONSIBILITY OF THE INSTALLER
REFLECTED CEILING PLAN - TRADITIONAL OR ASHRAE 170-2017 VERIFICATION - TRADITIONAL OR
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC- THE ULTRASUITE ARRAY IS SUPPLIED IN MULTIPLE FACTORY ASSEMBLED SECTIONS NO LARGER THAN 10'X4'- ASSEMBLED SECTION CONNECTIONS DONE IN FIELD BY OTHERS WITH FACTORY PROVIDED HARDWARE- LED LIGHTING IS FACTORY INSTALLED AND WIRED FOR EFFORTLESS ONSITE INSTALLATION- INSTALLATION AND MOUNTING OF THE ULTRASUITE ARRAY IS THE RESPONSIBILITY OF THE INSTALLER
USA SECTION BREAKDOWN - TRADITIONAL OR HGWC SECTION BREAKDOWN - TRADITIONAL OR
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
PHOTOMETRIC ANALYSIS - TRADITIONAL OR
ANSI/IES RP-29-16 RECOMMENDS 3000 LUX (279 FC) AT THE OPERATING TABLE.THE CALCULATED VALUES DO NOT INCLUDE OR ACCOUNT FOR ADDITIONAL LIGHTING.LIGHTING ANALYSIS HAS BEEN PERFORMED USING A COMBINATION OF LAB TESTED .IES FILES AND CALCULATED DATA.LIGHTING CALCULATIONS ARE ESTIMATED USING BEST PRACTICE AND MAY DIFFER SLIGHTLY FROM ACTUAL FIELD CONDITIONS.
LUMINAIRE HEIGHT: 10 FTCALCULATION ZONE: 3 FT
Maximum 332 fc Maximum 319 fc
Average 321 fc Average 227 fc
Operating Table Operating Area
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
REFLECTED CEILING PLAN - HYBRID OR/IMAGING SUITE ASHRAE 170-2017 VERIFICATION - HYBRID OR/IMAGING SUITE
- B12 STANDARD WHITE FINISH- PANEL CUTOUTS FOR BOOMS DONE IN FIELD BY OTHERS- RECOMMENDED INLET SIZE AND LOCATION SHOWN- THE CEILING IS FACTORY PREMANUFACTURED TO SIZES AND TOLERANCE +/- .032"- SITE ADJUSTMENTS TO PERIMETER SOFFITS AND/OR DRYWALL MAY BE REQUIRED
AND ARE THE RESPONSIBILITY OF THE INSTALLER
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
USA SECTION BREAKDOWN - HYBRID OR/IMAGING SUITE HGWC SECTION BREAKDOWN - HYBRID OR/IMAGING SUITE
- THE ULTRASUITE ARRAY IS SUPPLIED IN MULTIPLE FACTORY ASSEMBLED SECTIONS NO LARGER THAN 10'X4'- ASSEMBLED SECTION CONNECTIONS DONE IN FIELD BY OTHERS WITH FACTORY PROVIDED HARDWARE- LED LIGHTING IS FACTORY INSTALLED AND WIRED FOR EFFORTLESS ONSITE INSTALLATION- INSTALLATION AND MOUNTING OF THE ULTRASUITE ARRAY IS THE RESPONSIBILITY OF THE INSTALLER
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
PHOTOMETRIC ANALYSIS - HYBRID OR/IMAGING SUITE
Maximum 328 fc Maximum 315 fc
Average 308 fc Average 228 fc
Operating Table Operating Area
LUMINAIRE HEIGHT: 9.5 FTCALCULATION ZONE: 3 FT
ANSI/IES RP-29-16 RECOMMENDS 3000 LUX (279 FC) AT THE OPERATING TABLE.THE CALCULATED VALUES DO NOT INCLUDE OR ACCOUNT FOR ADDITIONAL LIGHTING.LIGHTING ANALYSIS HAS BEEN PERFORMED USING A COMBINATION OF LAB TESTED .IES FILES AND CALCULATED DATA.LIGHTING CALCULATIONS ARE ESTIMATED USING BEST PRACTICE AND MAY DIFFER SLIGHTLY FROM ACTUAL FIELD CONDITIONS.
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
UNISTRUT INTEGRATION DETAIL UNISTRUT LAYOUT - HYBRID OR/IMAGING SUITE
PRICE CEILING SYSTEM IS DESIGNED TO INTEGRATE WITH STRUCTURAL SUPPORT BY OTHERS.CEILING LEVEL UNISTRUT (OR EQUIVALENT) AND SUPPORT TO STRUCTURE ARE DESIGNED, PROVIDED, AND INSTALLED BY OTHERS
HGWC CENTER TO CENTER = UNISTRUT CENTER TO CENTER - 1 3/4"
PRICE SUPPLIED GASKET TO BE INSTALLED IN FIELDBY OTHERS
FIELD SUPPLIED AND INSTALLED FASTENERSMUST NOT PROTRUDE INTO THE UNISTRUTAT ANY POINT WHICH WOULD INTERFERE WITH POSITIONING OF THE FIXING BLOCK(REF VENDOR EQUIPMENT DRAWINGS)
PRICE SUPPLIED U-CHANNEL FILL PIECE COMPLETES CEILING WHEN ULTRASUITE MODULES EXTEND BEYOND UNISTRUT
PRICE SUPPLIED ALUMINUM CLOSURE STRIPSNAPS INTO BOTTOM OF UNISTRUT FINISH CEILING
FASTENING OF HGWC TEE TO UNISTRUT DONE IN FIELD BY OTHERS WITH HARDWARE PROVIDED BY OTHERS.PRICE RECOMMENDS CHECKING WITH STRUCTURAL ENGINEER PRIOR TO DRILLING OR PENETRATING STRUT PROFILE.
P1001 UNISTRUT (OR EQUIVALENT)PROVIDED AND INSTALLED BY OTHERS
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
TRANSLUCENTPOLYMER PERFORATED DIFFUSER FACE13% FREE AREA
STANDARD CONSTRUCTION- 14 GA (.064 THICK) ALUMINUM PLENUM- EXTRUDED ALUMINUM OUTER FRAME AND DIFFUSER FACE FRAME- TIG WELDED PLENUM, DIFFUSER FACE AND OUTER FRAME- ZINC PLATED EYE BOLTS FOR HANGING- ROOM SIDE ADJUSTABLE APERTURE PLATE DAMPER- 2 STAINLESS STEEL RETAINER CABLES PER DIFFUSER FACE- DIFFUSER FACE SECURED WITH COUNTERSUNK FLAT HEADMACHINE SCREWS
LED LIGHTING SPECIFICATIONS- LED LIGHTING INTEGRATED INTO EACH DIFFUSER MODULE- IP67 RATED LED STRIP WITH QUICK CONNECTORS- COLOR RENDERING INDEX (CRI) 90- L80 > 60,000 HRS.- FOR IES PHOTOMETRIC FILES VISIT:www.priceindustries.com/criticalenvironments/products/ultrasuite
FINISH- B12 STANDARD WHITE
LED COLOR TEMPERATURE- 5100K (5100 KELVIN)
LISTINGS- UL 1598 AIR-HANDLING LUMINAIRES- UL 2043 FIRE TEST FOR HEAT AND VISIBLE SMOKE RELEASE FOR DISCRETE PRODUCTSAND THEIR ACCESSORIES INSTALLED IN AIR-HANDLING SPACES
- UL2108 LOW VOLTAGE LIGHTING SYSTEM- UL8750 LIGHT EMITTING DIODE (LED) EQUIPMENT FOR USE IN LIGHTING PRODUCTS- UL1310 CLASS 2 POWER UNITS- UL94 FLAMMABILITY OF PLASTIC MATERIALS FOR PARTS IN DEVICES AND APPLIANCES- IP67 RATED INGRESS PROTECTION AGAINST DUST AND LIQUIDS- MIL-STD-461 FOR ELECTROMAGNETIC COMPATIBILITY
MIN MAX
2x2 24.250 24.250 12.000 22.000
2x3 24.250 36.375 12.000 22.000
2x4 24.250 48.500 12.000 22.000
NOMINAL
UNIT SIZE
LENGTH
(L)
WIDTH
(W)
HEIGHT (H)
LENGTH (L) WIDTH (W)
HEIGHT (H)
LOW VOLTAGETERMINAL BLOCK ENCLOSURE
ZINC PLATED EYEBOLTS FOR HANGING
2.000
- STANDARD HEIGHT (H) = 16"- MAX INLET HEIGHT = (H) - 8"
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
OPTIONAL ROOMSIDE HEPA FILTRATION
WIDTH (W)
LENGTH (L)
WIDTH (W) LENGTH (L) HEIGHT (H)
19.88 19.88 3.50
19.88 44.13 3.50
ACTUAL FILTER SIZE
NOTES - FILTER PLEATS RUN PARALLEL TO THE WIDTH (W) DIMENSION
- DIMENSIONS A & B TOLERANCES +/- 116
"
- FILTERS COME WITH GEL SEAL FILLED CHANNEL - FRAME DETAILS: - MATERIAL: ANODIZED EXTRUDED ALUMINUM
- THICKNESS: 116
" (MINIMUM)
- FILTERS ARE UL 900 CLASS 1 CERTIFIED - EFFICIENCY AND LEAK SCAN TESTED - HEPA EFFICIENCY: 99.99% (.3 MICRON) - MINIMUM MODULE WIDTH FOR ROOMSIDE HEPA FILTRATION IS 12"
VISIT PRICE INDUSTRIES WEBSITE FOR FILTER QUICK START GUIDEhttps://www.priceindustries.com/content/uploads/assets/literature/manuals/section%20e/ftr-room-side-replaceable-filter-rsr-quick-start-guide.pdf
GASKETED APERTURE PLATE DAMPER SEALS AGAINST HEPA FILTER FRAME
3/16" INTERNAL HEX SOCKET CAP-HEAD BOLTHOLDS DAMPER AND HEPA FILTER IN PLACESEPARATE HARDWARE FOR DAMPER AND HEPA ALLOWS FOR INDEPENDENT REMOVAL
FRAME HEIGHT (H)
APERTURE PLATE DAMPER ADJUSTABLE FROM ROOMSIDE
HEPA FILTER WITH GEL SEAL INSTALLS INTO ULTRASUITE KNIFE EDGE FRAME
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
- REMOTE DRIVER CABINETS REQUIRE SINGLE POINT HIGH VOLTAGE (120-277V~) CONNECTION (277V~ RECOMMENDED)
- 0-10V DIMMER SHIPS LOOSE. THE TOTAL 0-10V CONTROL SIGNAL WIRING FOR THIS CONTROL SHOULD NOT EXCEED 500 ft. DO NOT USE WIRE SMALLER THAN 20 AWG.
- 0-10V DIMMER CONTROLS UP TO 6 DRIVERS AT 120V~ AND UP TO 16 DRIVERS AT 277V~.
- LED DRIVERS SHIP FACTORY WIRED AND INSTALLED IN REMOTE DRIVER CABINET
- LED DRIVERS OFFER CONTINUOUS, FLICKER-FREE DIMMING FROM 100% TO 10% WITH RELAY SHUTOFF - OPTIONAL 0.1% DIMMING AVAILABLE
- ULTRASUITE MODULES COME WITH FACTORY WIRED AND INSTALLED TOP MOUNTED LOW VOLTAGE TERMINAL BLOCK ENCLOSURE
- INCOMMING HIGH VOLTAGE POWER AND LOW VOLTAGE CONNECTION BETWEEN ULTRASUITE MODULES AND REMOTE DRIVER CABINET ARE THE RESPONSIBILITY OF THE INSTALLER
- MAX DISTANCE BETWEEN ULTRASUITE MODULE AND REMOTE DRIVER CABINET IS DEPENDANT ON WIRE GAUGE TO MINIMIZE VOLTAGE DROP, SEE TABLE BELOW
- SEE ULTRASUITE INSTALLATION MANUAL AVAILABLE AT www.priceindustries.com FOR RECOMMENDED REMOTE DRIVER CABINET AND ULTRASUITE SYSTEM INSTALLATION
TYPICAL WIRING DETAILS
WIRING SCHEMATIC IS NOT TO SCALE AND IS SHOWN FOR REFERENCE ONLYINSTALLATION WORK AND ELECTRICAL WIRING MUST BE COMPLETED BY A CERTIFIED ELECTRICIAN
AND/OR QUALIFIED PERSON(S) IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES AND STANDARDS
WIRE GAUGE
(awg)
LENGTH OF WIRE
(feet)
18 15
16 25
14 45
12 70
10 115
LOW VOLTAGE WIRE
LENGTHS
CONNECTIONS BETWEEN REMOTE DRIVER CABINET AND DIFFUSER MODULE TERMINALBLOCK ENCLOSURE TO BE DONE IN FIELDBY OTHERS SEE TABLE FOR RECOMMENDED DISTANCE AND WIRE GAUGE
REMOTE DRIVER CABINETSACCEPT ONE SINGLE POINT HIGH VOLTAGE (120-277V~)CONNECTION PER CABINET
REMOTEDRIVER CABINET A
DETAIL A
LOW VOLTAGEWIRING BY OTHERS
LOW VOLTAGETERMINAL BLOCKENCLOSURE
ULTRASUITE ARRAY
HGWC LOOSE HALF TEEPERIMETER TRIM INSTALLEDIN FIELD BY OTHERS
HGWC WELDED GRID
COMMONPLENUM INLET
EYE BOLTS FOR HANGING
MOUNTING HOLES PROVIDEDHARDWARE PROVIDED BY OTHERS
OPERATINGROOM
EQUIPMENTCLOSET
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
CONNECTIONS BETWEEN REMOTE DRIVER CABINET AND DIFFUSER MODULE TERMINAL BLOCK ENCLOSURE TO BE DONE IN FIELD BY OTHERS
FIELD CONNECTION(FROM REMOTE
DRIVER CABINET)
FACTORY CONNECTION(FROM LED STRIP)
INSTALLATION WORK AND ELECTRICAL WIRING MUST BE COMPLETED BY A CERTIFIED ELECTRICIANAND/OR QUALIFIED PERSON(S) IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES AND STANDARDS
REMOTE DRIVER CABINET
ULTRASUITE MODULE
GNL
TYPICAL WIRING DETAILS
LOW VOLTAGE 0-10VFIELD CONNECTIONS
G
N
(+)
(-)
BARRIER TO SEPARATEHIGH VOLTAGE AND LOWVOLTAGE SIDE
ALL INTERNAL REMOTEDRIVER CABINET WIRINGIS DONE IN FACTORY
(+)
(-)
(+)
(-)
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
OPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED LED LIGHTING
USAULTRASUITE ARRAYOPERATING ROOM DIFFUSER SYSTEM WITH INTEGRATED
LED LIGHTING
KC
REMOTE DRIVER CABINETS SHIP WITH DRIVERS AND TERMINAL BLOCKS LABELED WITH THEIR CORRESPONDING DIFFUSER MODULE FOR EASY INSTALLATION
REMOTE DRIVER CABINETS
INSTALLATION WORK AND ELECTRICAL WIRING MUST BE COMPLETED BY A CERTIFIED ELECTRICIANAND/OR QUALIFIED PERSON(S) IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES AND STANDARDS
- REMOTE DRIVER CABINETS CAN BE WIRED SEPARATELY TO ALLOW FOR CRITICAL & NON CRITICAL CIRCUITS WITHIN A SINGLE ULTRASUITE SYSTEM
(-)(+)(-)(+)
U7-2U7-1
10 DRIVER REMOTE DRIVER CABINET
8 DRIVER REMOTEDRIVER CABINET
U1-1 U1-2
U2-1 U1-2
U3-1 U3-2
U4-1 U4-2
U5-1 U5-2
U6-1 U6-2
U7-1 U7-2
U8-1 U8-2
U9-1 U9-2
15 1/215 1/2
55 15/16
44 13/16
# OF DRIVERS L W H
2 11 7/16 15 1/2 5
4 22 9/16 15 1/2 5
6 33 11/16 15 1/2 5
8 44 13/16 15 1/2 5
10 55 15/16 15 1/2 5
12 67 1/16 15 1/2 5
REMOTE DRIVER CABINET
DIMENSIONS (INCHES)
O .265 MOUNTING HOLESTYPICAL x6
5 9/16TYP
1 7/16 (TYP)
25/32(TYP)
OF
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
![Klimaoprema katalog PPZEN DIFFUSER SLOT DIFFUSER ... Selection diagrams ... - Air velocity between two diffusers L [m] - Diffuser length B min](https://static.documents.pub/doc/80x56/5a9ff9c87f8b9a71178d6c6b/pdfklimaoprema-katalog-diffuser-slot-diffuser-selection-diagrams-air.jpg)
