Optical MEMS for Free-Space Communication
by
Lixia Zhou
B.S. (Tsinghua University) 1996 M.S. (University of California, Berkeley) 2002
A dissertation submitted in partial satisfaction of the requirements for the degree of
Doctor of Philosophy
in
Engineering – Electrical Engineering and Computer Sciences
in the
GRADUATE DIVISION
of the
UNIVERSITY of CALIFORNIA, BERKELEY
Committee in charge:
Professor Kristofer S. J. Pister, Co-chair Professor Joseph M. Kahn, Co-chair
Professor Roger T. Howe Professor Alice M. Agogino
Fall 2004
The dissertation of Lixia Zhou is approved:
________________________________________________________________ Professor Kristofer S. J. Pister, co-chair Date
________________________________________________________________ Professor Joseph M. Kahn, co-chair Date
________________________________________________________________ Professor Roger T. Howe Date
________________________________________________________________ Professor Alice M. Agogino Date
University of California, Berkeley
Fall 2004
Optical MEMS for Free-Space Communication
Copyright 2004
by
Lixia Zhou
Abstract
Optical MEMS for Free-Space Communication
by
Lixia Zhou
Doctor of Philosophy in Engineering - Electrical Engineering and Computer Sciences
University of California, Berkeley
Kristofer S. J. Pister, Co-chair
Professor Joseph M. Kahn, Co-chair
The convergence of MEMS technology with communication and digital circuitry
makes high-speed, low power, free-space communication links over distances up to
several km possible. MEMS corner cube retroreflectors (CCRs) are proposed to work
as a passive optical transmitter, sending collected information back to an interrogating
center. MEMS scanning micromirrors are proposed to steer a modulated laser beam
in order to establish a secure optical link between rapidly moving platforms.
Sub-millimeter-sized quad CCRs are fabricated by assembling two side mirrors
onto an actuated bottom mirror. An angular alignment accuracy of < 0.06° is achieved
through locking the two side mirrors using spring flexures and protrusion-notch
structures. The quad CCR incorporates a gap-closing actuator to deflect a base mirror,
allowing their reflectivity to be modulated up to 7 kb/s by a drive voltage less than 5
V. A 180-m free-space optical communication link using a CCR as the transmitter is
demonstrated. CCRs have been integrated into miniature, autonomous “Smart Dust”
1
nodes that constitute a distributed wireless sensor network. A signal-to-noise ratio
analysis of CCR-based links is also presented, considering the impact of CCR
dimensions, link distance, and other factors.
An SOI/SOI wafer bonding process is developed to fabricate scanning
micromirrors using lateral actuation. The process is an extension of the SOI
technology and can be used to fabricate stacked high-aspect-ratio structures with
well-controlled thicknesses. The fabricated one-axis micromirror scans up to 21.8°
optically under a DC actuation voltage of 75.0 V and has a resonant frequency of 3.6
kHz. The fabricated two-axis micromirror scans up to 15.9° optically for the inner
axis at 71.8 V and 13.2° for the outer axis at 71.2 V. The micromirror is observed to
be quite durable and resistant to shocks.
Torsional beams with T-shaped cross sections are introduced to replace
rectangular torsional beams in two-axis MEMS micromirrors in order to reduce the
cross-coupling between the two axial rotations. The fabricated bi-directional two-axis
micromirror works up to ±7° for the outer-axis and from -3° to 7° for the inner-axis
under DC actuation.
Professor Kristofer S. J. Pister, Co-chair Date
Professor Joseph M. Kahn, Co-chair Date
2
I dedicate this thesis to my husband, Gang Wang.
i
TABLE OF CONTENTS
1. INTRODUCTION .......................................................................................................... 1
1.1. Free-Space Optical Communication Using CCRs and Scanning Micromirrors ...... 1
1.2. Background of Designing CCRs as 3D Devices...................................................... 3
1.3. Background of Designing Scanning Micromirrors .................................................. 4
1.4. Outline of Dissertation ............................................................................................. 6
2. MEMS CORNER CUBE RETROREFLECTORS (CCRs) ........................................... 7
2.1. Overview of SOI-Based CCRs................................................................................. 7
2.2. Design and Fabrication of CCRs.............................................................................. 8
2.2.1. Design of gap-closing actuator .......................................................................... 9
2.2.2. Design of structure-assisted assembly ............................................................. 11
2.2.3. Fabrication ....................................................................................................... 12
2.3. Performance of Fabricated CCRs........................................................................... 15
2.3.1. DC and AC actuation of fabricated CCRs....................................................... 15
2.3.2. Optical performance of fabricated CCRs ........................................................ 20
2.4. Signal-to-Noise Ratio Analysis of CCR-Based Links ........................................... 27
2.5. Integration into Sensor Nodes ................................................................................ 33
3. MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING
PROCESS ......................................................................................................................... 38
3.1. Design of Scanning Micromirrors Using Lateral Actuation .................................. 39
3.2. SOI/SOI Wafer Bonding Process ........................................................................... 40
3.2.1. Bonding mechanism ........................................................................................ 41
3.2.2. Minimizing bow for SOI wafers...................................................................... 42
3.2.3. Strategies to enhance bonding ......................................................................... 47
ii
3.2.4. Detailed process flow ...................................................................................... 48
3.3. Bond Characterization............................................................................................ 50
3.3.1. Diagnosis of bonded structures by SEM and infrared images......................... 50
3.3.2. Electrical interconnection realized by bonded structures ................................ 52
3.3.3. Shear stress test of bonded structures .............................................................. 56
3.3.4. Air sealing by bonded structures ..................................................................... 58
3.4. Mechanical Modeling and ANSYS Simulation of Micromirrors .......................... 62
3.4.1. Analytical simulation....................................................................................... 62
3.4.2. ANSYS simulation .......................................................................................... 71
3.5. Performance of Scanning Micromirrors................................................................. 73
3.5.1. DC and AC actuation of fabricated one-axis scanning micromirrors.............. 75
3.5.2. DC and AC actuation of fabricated two-axis scanning micromirrors ............. 80
3.6. Reliability and Robustness of Micromirrors .......................................................... 82
3.6.1. Reliability of micromirrors .............................................................................. 82
3.6.2. Shock resistance of micromirrors .................................................................... 85
4. MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS ...... 89
4.1. Torsional Beams with T-Shaped Cross Section..................................................... 89
4.2. ANSYS FEM Simulation ....................................................................................... 91
4.3. DC and AC Actuation of Micromirrors with T-bar Torsional Beams ................... 93
4.4. Comb Drive Actuators for Large Displacements ................................................... 97
5. CONCLUSIONS AND DISCUSSIONS .................................................................... 101
5.1. Summary of Results over CCRs........................................................................... 101
5.2. Summary of Results over Scanning Micromirrors and SOI/SOI Wafer Bonding
Process......................................................................................................................... 102
5.3. Future Work ......................................................................................................... 104
REFFERENCE ............................................................................................................... 108
iii
APPENDIX A – MATLAB SCRIPTS TO MODEL FAR-FIELD IMAGE PATTERN
REFLECTED BY CCRS ................................................................................................ 116
APPENDIX B – MATLAB SCRIPTS TO MODEL DSCS RELATED WITH
MISALIGNMENT ANGLE OF CCRS.......................................................................... 118
APPENDIX C – SOI/SOI WAFER BONDING PROCESS FLOW.............................. 120
C1. Layout Features / Design Rules ........................................................................ 120
C2. Detailed Process Flow....................................................................................... 121
APPENDIX D – ANSYS SCRIPTS TO MODEL MECHANICS OF SCANNING
MICROMIRRORS ......................................................................................................... 126
APPENDIX E – MATLAB SCRIPTS TO CALCULATE THE CURVATURE OF A
MULTILEVEL WAFER ................................................................................................ 128
iv
ACKNOWLEDGMENTS
I have really enjoyed five years of graduate student life here at Berkeley, including
many sleepless nights, years of hard work, and most important of all, invaluable
experience of learning from mentors and colleagues. I would like to thank Professor
Joseph Kahn for taking me into his research group; as a result, I accidentally bumped into
MEMS area and beheld the beauty of this continuously-developing field. Professor Kris
Pister inspired me on many aspects due to his enthusiasm, sense of humor, and never-
dying confidence. I would also like to thank my two other committee members, Professor
Roger Howe and Professor Alice Agogino for their support and constructive advise on
the thesis.
Veljko Milanovic showed me what is hard-working; because of him, I learned how to
have fun when working in the Microlab. Thanks to Mathew Last for giving advice in
series of design review and contributing greatly to my research. I would also like to thank
Michael Cohn, Hongbing Liu, Daniel McCormick, Hyuck Choo, Sunghoon Kwon, Baris
Cagdaser, Robert Conant, Matthew Wasilik, Xiaofan Meng, Ning Chen, and Christopher
Keller, for sharing tricks in the Microlab and/or providing help in conducting research.
I thank other students and doctors in 471 Cory, Brian Leibowitz, Brett Warneke, Seth
Hollar, Anita Flynn, Sarah Bergbreiter, Michael Scott, Richard Yeh, Colby Bellew,
Lance Doherty, Chinwuba Ezekwe, and Steven Lanzisera, for broadening my view on
other fields, such as integrated circuits and robotics.
I would like to thank our grant administrator, Tom Parsons, for his patience in
arranging trips, paper submission, and many other routines.
v
Special thanks to my friend, Jinwen Xiao, for being a partner to our constantly-
changing hobbies, from tennis, table tennis, to swimming. I thank Jianyang Xu for
inviting me to so many trips and giving terrific breaks from the intense graduate student
life. I would also like to thank many of my friends, Xinyan Deng, Qiang Lu, Jin Wang,
Wei Mao, Xiaoming Zhu, and Roy You, for being together and earning Ph.D titles side
by side.
Many thanks to my conference buddies, Raffi Kamalian and Ye Wang, for having
good time together in IABs and MEMS conferences.
Thank Mehrdad Roosta from Iolon, Inc. for helping me to perform shock test. Thank
Bart Mathewson for helping me in drawing the cool 3D schematic layout.
Finally, I would like to thank my husband, Gang Wang, for his unlimited patience,
encouragement, and love throughout thick and thin.
vi
INTRODUCTION
1. INTRODUCTION
This dissertation describes the development of two Microelectromechanical Systems
(MEMS) devices, corner cube retroreflector (CCR) and scanning micromirror, which are
used for free-space optical communication.
1.1. Free-Space Optical Communication Using CCRs and Scanning Micromirrors
Free-space optical communication has attracted considerable attention for a variety of
applications where line-of-sight is applicable, such as metropolitan network extensions
[1], last-mile Internet access [2], inter-satellite communication [3], and earth-to-space
links [4]. Optical communication offers significant advantages over radio frequency (RF)
communication, including secure link, wide bandwidth, small terminals, low power
consumption, freedom from frequency allocation issues, and simultaneous multi-node
communication capabilities. Thus optical communication is favored when building a
compact, high transmission rate, and low power communication system where the line-
of-sight constraint is satisfied.
One of the key components in this two-way free space optical communication system
is a compact, reliable, and inexpensive laser beam steering device that provides a fast
scanning capability for pointing, acquisition, tracking, and data communication. A
scanning micromirror based on the technology of MEMS is introduced to fulfill this
requirement [5][6]. MEMS scanning micromirrors can be built with flat and reflective
mirror surfaces, high optical resolution, fast scanning capability, reliable actuating
mechanism, and large volume production.
1
INTRODUCTION
MEMS phased arrays composed of groups of relatively small micromirrors are also
proposed to scan the laser beam [7][8]. They can be actuated through large deflection
angles with substantially reduced response time. But they involve more complicated
actuator design, i.e., not only capable of rotations around the two axis, but also able to
move vertically to compensate the phase difference between mirrors. Also active
feedback controls over individual mirrors can be very complicated.
The emergence of distributed sensor network systems brings on a demand for a
communication platform with extremely small power consumption [9][10][11][12]. That
is when CCRs come into play. Zwirn proposed to use a microfabricated CCR as a free-
space optical transmitter [13]. An unactuated CCR consists of three mutually orthogonal
mirrors that form a concave corner, thus light incident on this ideal CCR (within an
appropriate range of angles) is reflected back to the source. By modulating the orientation
of one of the three mirrors, an on-off-keyed digital signal can be transmitted back to the
interrogating light source. Such a CCR has been termed a “passive optical transmitter”
because it can transmit without incorporating a light source. An electrostatically actuated
CCR transmitter offers the advantages of small sizes, relatively fast transmission rates,
low power consumption and convenient integration with solar cells, sensors and CMOS
control circuits. CCR transmitters have been employed in miniature, autonomous sensor
nodes (“dust motes”) in the Smart Dust project [14].
MEMS micromirrors are used for actively transmitting data when the system requires
a seeking and tracking ability, such as scanning the interrogating laser beam at the base
station of a distributed sensor network system or steering the coded laser beam between
two moving unmanned air vehicles. MEMS CCRs are intended to passively transmit
2
INTRODUCTION
digital signals for a platform with relatively low transmission rates and extremely small
power budget, such as in a Smart Dust sensor mote.
1.2. Background of Designing CCRs as 3D Devices
Fabrication of three-dimensional structures with precisely positioned out-of-plane
elements poses challenges to current MEMS technologies. One way to achieve three-
dimensional structures is to rotate parts out-of-plane on micro-hinges [15][16]. Previous
CCRs have been fabricated in the MUMPS process [17][18] and side mirrors were
rotated out-of-plane on hinges. However, these CCRs had non-flat mirror surfaces and
high actuation voltages. Most importantly, the hinges released from surface-
micromachined processes typically have gaps, permitting motion between linked parts.
Thus the out-of-plane structures attached to the substrate through this kind of hinges were
not able to obtain accurate vertical alignment and CCRs fabricated in this way had poor
retroreflective efficiency.
Using an elastic hinge instead of structural hinges composed of interdigitated layers
improves the alignment scenario tremendously. Structures can be bent out of plane by
utilizing either the large residual stress difference between two kinds of thin films
(bymetal hinges) [19], the thermal shrinkage of cured polyimide (polyimide hinges) [20],
or the surface tension forces of melting thick photoresist pads (photoresist hinges) [21].
Small radii of bending can be obtained through these methods and adding carefully-
designed interlocking braces allows a better control over the orientations of out-of-plane
structures. It is reported that photoresist hinges self assembly structures with a yield as
high as 75% and angle accuracy of 1.8 mrad [21].
3
INTRODUCTION
However, the elastic hinges have the drawback of occupying a large area on chip due
to the scheme of rotating structures out-of-plane from the chip surface and the existence
of those interlocking braces. Also the rotation actuator implemented in this process
displays an extremely high actuation voltage [22], which will become a problem to
design driving circuits on an autonomous sensor node.
Here we propose a new scheme, structure-assisted assembly, to fabricate and
assemble compact CCRs that achieve accurate alignment between three mirrors and
operate under a conveniently low actuation voltage [23]. The assembly-assisting
structures include V-grooves and spring clamps, which are widely used to align fibers
with other optical devices to achieve high coupling efficiency [24][25]. V-grooves can
guide the assembled structures into the desired position and spring clamps are employed
to maintain out-of-plane structures on accurate orientation.
1.3. Background of Designing Scanning Micromirrors
Scanning micromirrors have been developed for a wide range of applications in
addition to steering laser beams, such as optical crossbar switches [26], digital projectors
[27], barcode readers [28], adaptive optics [29], and tunable lasers [30]. However, the
purpose of laser beam steering for free space optical communication brings on different
requirements over scanning micromirrors, such as large mirror sizes (~1 mm in
diameter), rotation ability over two axis, large DC scan angles (±10° optical), fast
switching ability (transition time between positions < 100 µs), and strong shock
resistance (hundred Gs).
While surface micromachining generally does not offer considerable scanning range
for a large size mirror, MEMS micromirrors based on silicon-on-insulator (SOI) wafers
4
INTRODUCTION
and deep reactive ion etching (DRIE) technology overcome this problem by having an
etched cavity under the scanning micromirror. It also provides attractive features such as
perfect mirror flatness, high-aspect-ratio springs, and thus small cross-mode coupling.
Many strategies have been developed around these two technologies in order to make
scanning micromirrors with large size mirrors, wide steering angles, and fast responding
speed. Conant et al first presented a vertical comb drive actuator fabricated on the two
layers of a SOI wafer [31]. However, their process requires an accurate alignment
between two layers in different heights (~ 50 µm). Consequently, several self-alignment
fabrication processes were developed to enable precise alignment between vertically
stacked layers [32][33]. Another way to tackle this alignment problem is using a
photoresist hinge to rotate [34] or plastically displacing [35] a group of comb fingers out-
of-plane so that two groups of comb fingers remain to be perfectly spaced and form an
angular comb drive actuator.
Although vertical/angular comb drive actuators provide high force density, it has
difficulty in producing two-axis scanning micromirrors with comparable steering
performance on both axial rotations. Kwon et al used a backside island to provide
electrical isolation and mechanical coupling for a two-axis scanning micromirror [36],
but this device has a much lower resonance frequency in the outer axial rotation than that
of the inner axial rotation. Milanovic et al used mechanical rotation transformers to
produce a two-axis scanning micromirror with high resonant frequencies [37], but the
steering range is limited.
Scanning micromirrors realized by an off-axis lateral force overcome the alignment
issue in vertical comb drive actuators and its advantages also include small momentum of
5
INTRODUCTION
inertia, a large actuation force, and consequently a large scanning angle and fast response
[38]. We propose an SOI/SOI wafer bonding process to fabricate scanning micromirrors
actuated by a lateral comb drive actuator.
1.4. Outline of Dissertation
The following chapters in this dissertation address in detail the design and fabrication
of CCRs and scanning micromirrors. Chapter 2 presents the design, fabrication,
assembly, testing over optical and electrical performance, and integration of CCRs with
other components of Smart Dust motes. Chapter 3 describes the design, fabrication,
mechanical modeling, and testing of scanning micromirrors manufactured by an SOI/SOI
wafer bonding process. In Chapter 4, torsion beams with T-shaped cross sections are
introduced to overcome the cross-coupling problem existing in the two-axis scanning
micromirrors with rectangular torsion beams. Chapter 5 concludes the dissertation by
reviewing the features of the SOI/SOI wafer bonding process and the possible
applications with this process. Outstanding issues and directions for future work,
including better design of comb drive suspension springs, are outlined.
6
MEMS CORNER CUBE RETROREFLECTORS
2. MEMS CORNER CUBE RETROREFLECTORS (CCRs)
The Smart Dust project aims to integrate a power source, multiple sensors, a micro
computer, and a communication platform, forming a miniature, autonomous sensor mote.
CCRs serve as a passive transmitter for the Smart Dust mote working under extremely
low power consumption to transmit signals collected by the sensors on the mote back to
an interrogating center.
CCRs modulate the reflected light intensity by modulating the orientation of one of
their three orthogonal mirrors. In order to achieve high signal to noise ratio at the
interrogating center which is several hundred meters away, CCRs must have mirror
surfaces which are extremely flat and highly reflective. Moreover, mirrors must maintain
strict orthogonality when CCRs are not actuated. As the data transmission rate depends
on how fast the orientation of the mirror in CCRs is modulated, it is desirable to have a
high resonance frequency over the rotation mode of the actuated mirror. Also the driving
voltage needs to be low in order to conveniently integrate with CCRs’ power source and
driving circuits.
2.1. Overview of SOI-Based CCRs
We introduce a new scheme, structure-assisted assembly, to fabricate and assemble
CCRs that achieve accurate alignment of out-of-plane parts. The optical and electrical
properties of CCRs produced through this method are superior to previous CCRs
fabricated in the MUMPS process. Improvements include a tenfold reduction in mirror
curvature, a threefold reduction in mirror misalignment, a fourfold reduction in drive
7
MEMS CORNER CUBE RETROREFLECTORS
voltage, an eightfold increase in resonance frequency, and improved scalability due to the
quadruplet design.
Here we present detailed information about the design, fabrication, and performance
of these quad CCRs. We describe an experimental free-space optical link using a CCR
transmitter, and present an analysis of the signal-to-noise ratio (SNR) of CCR-based
optical links. Fabricated CCR is incorporated with other parts of Smart Dust mote and
transmits signals collected by the accelerometer and light-level sensor.
2.2. Design and Fabrication of CCRs
The layout of CCR side mirrors and bottom mirror is displayed in Figure 2-2 and the
SEM picture in Figure 2-2 shows a fabricated and assembled CCR. The two side mirrors
are assembled into the V-grooves on the chip, while the bottom mirror is designed to be
torsionally actuated so that it can modulate the light intensity of the retro-reflected light
beam.
Notch
Protrusion V-groove
Actuation Stop
Notch
Protrusion V-groove
Actuation Stop
Notch
Protrusion V-groove
Actuation Stop
V-groove
Actuation Stop
Figure 2-1. Layout of CCR side mirrors and bottom mirror.
8
MEMS CORNER CUBE RETROREFLECTORS
Torsional Spring Beam
Side Mirror 1
Side Mirror 2
Actuated Bottom Mirror
Actuation Stop
Tether
Torsional Spring Beam
Side Mirror 1
Side Mirror 2
Actuated Bottom Mirror
Actuation Stop
Tether
Figure 2-2. SEM picture of assembled CCR quadruplet. Note the spring-locks
beside the V-grooves to grab the feet of the side mirrors and the notch-
protrusion clutch at the top of the side mirrors to achieve more accurate
positioning. The extended beams with triangular heads act as limit
stops for the gap-closing actuator, and land on electrically isolated
substrate islands after the moving mirror pulls-in.
9
2.2.1. Design of gap-closing actuator
We have chosen to fabricate CCRs on silicon-on-insulator (SOI) wafers to obtain flat
and smooth mirror surfaces. The chemical mechanical polishing gives SOI wafer surfaces
a RMS (root-mean-square) roughness on the order of nanometer. Also the total thickness
variation of the device layer across a 100 mm-diameter SOI wafer can be as small as 1
µm, producing a very flat mirror surface.
MEMS CORNER CUBE RETROREFLECTORS
An electrostatic gap-closing actuator is an appropriate choice for modulating the
orientation of a CCR mirror. It provides a high actuation torque and thus low driving
voltage. The actuated mirror is fabricated in the device layer of the SOI wafer and
suspended by two torsional springs. The device layer and substrate layer of the SOI wafer
conveniently form the opposing electrodes of a gap-closing actuator. With half of the
substrate layer under the mirror etched away, the gap-closing actuator provides a pure
torsional moment when a voltage is applied between the mirror and the underlying
substrate. The narrow gap (the one we choose is 2 µm) between the device layer and
substrate layer provides an angular deflection of 5.7 mrad for a mirror plate with a side
length of 350 µm. This amount of angular deflection induces an enormous change over
the retro-reflected light intensity, giving an on-off signal ratio of over 20 dB, which is
sufficient for the purpose of modulating the signal level digitally. At the same time, the
narrow gap size enables high actuation moment with low drive voltage, as electrostatic
actuation force inversely depends on the square of the gap size between electrodes.
Another advantage of this gap-closing actuation design is that it decouples the sizing
of the actuated mirror from the sizing of the actuator. The substrate electrode lies under
the mirror plate, spanning from the center of the mirror plate to the root of two extended
beams on the device layer, whose position determines the size of the actuator. The
extended beams act as mechanical stops to prevent shorting between the two actuator
plates when the moving mirror reaches pull-in position. After pull-in, the triangular-
shaped stops make point contact with electrically isolated islands on the substrate,
minimizing stiction and allowing the release of the mirror when the actuation voltage is
removed. The amount of angular deflection and pull-in voltage depends on the position of
10
MEMS CORNER CUBE RETROREFLECTORS
the extended beams while the mirror plate may be designed larger to reflect sufficient
light for the intended communication range.
The tethers between the moving mirror and the rest of the chip in Figure 2-2 hold the
actuated mirror in place, preventing it from sticking to the substrate when releasing. They
are broken by probes after the assembly.
2.2.2. Design of structure-assisted assembly
Two groups of V-grooves are patterned in the device layer to assist the insertion of
the two side mirrors. They are situated orthogonally around the actuated bottom mirror.
Each of the side mirrors has “feet” that can be easily inserted into the larger open end of
the V-grooves. Also the substrate under the V-grooves has been etched away to facilitate
this insertion. After the insertion, the side mirrors are pushed toward the smaller end of
the V-grooves, where the feet are anchored by springs next to the V-grooves which are
spaced apart by a distance slightly smaller than the thickness of the side mirror. One side
mirror has a notch at the top and the other side mirror has a spring-loaded protrusion at
the top; after assembly, the protrusion on one side mirror locks into the notch on the other
side mirror, maintaining accurate alignment between the two mirrors.
In this way, we can naturally fabricate four CCRs that share a common actuated
bottom mirror, although the performance of those four CCRs may differ because of the
asymmetrical positioning of the side mirrors and the presence of etching holes on part of
the actuated mirror plate. Compared to other single CCR designs, the quadruplet design
increases the probability of reflecting the light back to the base station without
significantly increasing die area or actuation energy.
11
MEMS CORNER CUBE RETROREFLECTORS
2.2.3. Fabrication
As shown in Figure 2-3, the process starts with a double-side-polished SOI wafer
with a 50 µm device layer and a 2 µm buried oxide layer. First, a layer of thermal oxide
with 1 µm thickness is grown on both sides of wafer at 1100oC. We pattern the front-side
oxide with the device-layer mask. The main structures are on this layer, including the
bottom mirror, two torsional spring beams suspending the bottom mirror, gap-closing
actuation stops, and V-grooves for anchoring the side mirrors. Then we flip the wafer
over, deposit thick resist, and pattern the back-side oxide using the substrate-layer mask.
The substrate layer functions as the second electrode of the gap-closing actuator and
provides two electrically isolated islands as the pull-in stop for the actuator. We perform
DRIE etching from the back-side first. After etching through the substrate, we continue
the etching to remove the exposed buried oxide, reducing the residual stress between the
buried oxide and device layer that might otherwise destroy the structures after the front-
side etching. Then we DRIE etch the front-side trenches. After etching, the whole chip is
dipped into concentrated HF for about 10 min, to remove the sacrificial oxide film
between the bottom mirror and substrate. There is no need to employ critical-point drying
after release, because the tethers between the moving mirror and the rest of the chip hold
the actuated mirror in place, preventing it from sticking to the substrate.
12
MEMS CORNER CUBE RETROREFLECTORS
SCS Wet oxide Thick resist
Pattern both sides
HF wet release
Frontside etch
Backside etch
Wet oxidation
SCS Wet oxide Thick resist
Pattern both sides
HF wet release
Frontside etch
Backside etch
Wet oxidation
Figure 2-3. Bottom mirror fabrication process.
The side mirrors can be fabricated in the same process or by another standard single-
mask process on a SOI wafer. A separate process provides more flexibility over choosing
the thicknesses of the device layer, i.e., the thickness of the side mirrors, bottom mirror,
and supported suspension beams. We patterned the device layer with the shape of side
mirrors, followed by a long-duration HF release.
13
MEMS CORNER CUBE RETROREFLECTORS
(a) Before assembly:
Side mirror 2
Side mirror 1
Bottom mirror
(b) After inserting side mirror 1:
(c) Finally insert side mirror 2:
(a) Before assembly:
Side mirror 2
Side mirror 1
Bottom mirror
(b) After inserting side mirror 1:
(c) Finally insert side mirror 2:
Figure 2-4. Assembly sequence. Snap locks yield alignment accuracy better than 1
mrad.
14
When both the bottom mirror and side mirrors are ready, we mount the side mirrors
onto the bottom mirror manually to form a fully functional CCR. Figure 2-4 shows the
sequence of assembly. First, we pick up side mirror 1, using a pair of fine-tip tweezers.
We insert it into the large-opening end of the V-grooves around the bottom mirror and
push it into the slot, where the feet of side mirror 1 are grabbed by the springs beside the
V-grooves. Then we pick up side mirror 2 and insert into the perpendicular V-grooves.
When both mirrors are pushed to the end of V-grooves, the spring-loaded protrusion on
one side mirror is locked into the notch on the other side mirror and these spring-loaded
structures ensure that the side mirrors remain in correct alignment. This assembly process
MEMS CORNER CUBE RETROREFLECTORS
can be completed within several minutes under a stereomicroscope. After assembly, we
use a probe to finely tune the position of side mirrors and use UV-curable epoxy to secure
the side mirrors to the chip. As silicon reflects only about 30% of visible light, we
evaporate a 50 nm-thick layer of gold either before or after assembly without masking, to
increase the optical reflectivity of the CCRs.
2.3. Performance of Fabricated CCRs
In the Smart Dust project, the CCR needs to operate with an actuation voltage less
than 5 V, to be compatible with solar cell power and low-voltage CMOS control signals.
The modulation speed of the CCR should be in the range of several kb/s. Most
importantly, the optical performance of CCR has to be good enough to transmit a signal
for several hundred meters with low bit-error probability.
2.3.1. DC and AC actuation of fabricated CCRs
x
gθ
(a) (b)
x
gθ
x
gθ
(a) (b)
Figure 2-5. A simple model of the gap-closing actuator in CCRs. (a) Mirror
suspended by two torsional beams; (b) Cross section of CCR bottom
mirror, switching from “1” state to “0” state.
The bottom mirror in CCRs can be modeled as a torsionally suspended mirror
actuated with a gap-closing electrostatic actuator, as shown in Figure 2-5. The deflection 15
MEMS CORNER CUBE RETROREFLECTORS
of the actuated mirror takes place under the resultant of the electrostatic torque and spring
torque. This gap-closing actuator has a pull-in position and pull-in voltage different from
the simple cantilever case with a gap-closing actuator on the tip [39]:
m
inpull Wg4404.0=−θ (2-1)
2/1
0
3685.9⎟⎟⎠
⎞⎜⎜⎝
⎛= −
−m
inpullinpull L
KV
εθθ (2-2)
where g is the actuator gap, i.e., the thickness of buried oxide layer in the SOI wafer.
Here, Wm and Lm are the width and length of the actuator plate, and Kθ is the torsional
spring constant of two suspending beams.
Figure 2-6 shows experimental results of deflected angle versus applied voltage, as
well as the theoretical calculations. Experiments demonstrate a DC pull-in voltage as low
as 4.7 V and a pull-in angle of approximately 0.4·g/Wm, in good agreement with
theoretical predictions. Notice that the full angular travel of the actuator is g/Wm
theoretically, which is 6.7 mrad for a gap distance of 2 µm and an actuator width of 300
µm. In experiments, the actuated mirror of CCRs is deflected by 5.7 mrad at most
because the gap-closing stops prevent the moving mirror from crashing to the other
electrode node. This gives a difference in the deflected angles after pull-in between the
experimental and theoretical values.
16
MEMS CORNER CUBE RETROREFLECTORS
0
1
2
3
4
5
6
7
0 1 2 3 4 5 6
Actuation Voltage (V)
Ang
le D
ispla
cem
ent (
mra
d)
Experimental
Theoretical
Figure 2-6. Actuator angular displacement vs. applied DC actuation voltage.
The mechanical resonance frequency of the actuated plate is given by
2/1
21
⎟⎟⎠
⎞⎜⎜⎝
⎛=
mIkf θ
π (2-3)
where Im is the moment of inertia of the actuated plate.
The frequency response of one CCR, measured using a POLYTEC laser Doppler
vibrometer, is shown in Figure 2-7. A pure sinusoidal voltage source is applied to the
gap-closing actuator and a lock-in amplifier senses the output signal at twice the
frequency of the drive signal. Electrical resonance occurs at 2.2 kHz, corresponding to a
mechanical resonance frequency of 4.4 kHz. Because the actuation torque is proportional
to V2, the torque is applied at twice the frequency of the electrical drive signal. The
17
MEMS CORNER CUBE RETROREFLECTORS
frequency at which the squared amplitude is half its DC value is around 3.5 kHz. This
corresponds to a mechanical cut-off frequency of about 7.0 kHz, implying that the CCR
can be digitally modulated up to about 7 kb/s. A much higher modulation speed could be
achieved by fabricating the bottom mirror on a SOI wafer having a decreased device-
layer thickness, with little or no impact on other performance characteristics of the CCR.
1.0E-08
1.0E-07
1.0E-06
1.0E-05
100 1000 10000
Electrical Drive Frequency (Hz)
Am
plitu
de o
f Vel
ocity
(a.u
.)
10-5
10-6
10-7
10-81.0E-08
1.0E-07
1.0E-06
1.0E-05
100 1000 10000
Electrical Drive Frequency (Hz)
Am
plitu
de o
f Vel
ocity
(a.u
.)
10-5
10-6
10-7
10-8
Figure 2-7. Frequency response of the actuated bottom mirror plate.
18
Figure 2-8 presents the step response of a CCR to a 250 Hz square wave. At t = 0.5
ms, the actuation voltage is turned off. The actuated mirror is restored to its relaxed
position under the restoring torque of the torsional springs, turning on the beam reflected
from the CCR. At t = 2.5 ms, the actuation voltage is turned on, pulling down the
actuated mirror, and turning off the beam reflected from the CCR. Both release and pull-
down exhibit transition times of about 55 µs. When the mirror is released, it exhibits
MEMS CORNER CUBE RETROREFLECTORS
ringing for about 1 ms before settling to the relaxed position. The 1 ms settling time
implies a maximum modulation rate of about 1 kb/s. Fortunately in this process we can
add an isolated substrate area under the actuated plate to obtain increased squeeze-film
damping after release of the actuation voltage. We have demonstrated that this can
greatly reduce the settling time, permitting the maximum modulation speed to be limited
only by the resonance frequency.
-4
-2
0
2
4
6
8
0 1 2 3 4 5
Time (ms)
Ang
le D
ispl
acem
ent (
mra
d)
Plate pull-in
Plate released
-4
-2
0
2
4
6
8
0 1 2 3 4 5
Time (ms)
Ang
le D
ispl
acem
ent (
mra
d)
Plate pull-in
Plate released
Figure 2-8. Response of the actuated bottom mirror plate to a 250 Hz square wave.
A major goal of the Smart Dust project [40] is to minimize the energy per bit required
for transmission. The capacitance of the CCR changes from around 1.3 pF before pull-in
to 3 pF after pull-in. The actuation voltage is around 5 V. A rough estimate of the energy
expended during each pull-in action is CV2 ≈ 75 pJ (no energy is required to release the
CCR). Assuming non-return-to-zero encoding, energy is required only when the 19
MEMS CORNER CUBE RETROREFLECTORS
transmitted bit transitions from ‘1’ to ‘0’, so that the average energy consumption is
about 19 pJ/bit. This compares quite favorably to other (RF) approaches such as
Bluetooth, which has a fundamental transmission cost of 1 nJ/bit over a communication
distance of a few 10s of meters.
2.3.2. Optical performance of fabricated CCRs
A useful parameter describing the optical performance of CCR is the differential
scattering cross section (DSCS). It is defined as [41]
i
ooi
o ILInn
dd 2
)ˆ,ˆ( =Ωσ (2-4)
where is the incident light direction, is the reflected light direction, Iin on i is the light
intensity incident on the CCR, Io is the reflected light intensity at the observation plane
and L is the distance between the CCR and the observation plane. Note that the DSCS has
dimensions of m2/sr. The DSCS depends on the mirror dimensions, mirror flatness,
mirror surface quality, mirror reflectivity, and relative alignment between the mirrors. In
addition, the DSCS depends on the directions of the incident and reflected beams. For a
CCR with three identical square mirrors, the DSCS is largest for incident and reflected
directions close to the body diagonal, i.e., and near in on )1,1,1(3
1 .
If we illuminate an unactuated CCR with laser light, the far-field diffraction pattern
corresponds to the DSCS for reflected light directions close to . Since an
unactuated CCR reflects a laser beam back to the same direction as the incoming light, a
special optical setup has to be employed to separate the outgoing light from the incoming
light and allow the detection of its far-field diffraction pattern. As shown in Figure 2-9, a
on in−
20
MEMS CORNER CUBE RETROREFLECTORS
linearly polarized laser beam is first oriented to fully pass through a polarized beam
splitter. The following quarter-waveplate changes its linear polarization to circular. After
three reflections off an unactuated CCR, the light returns with the opposite circular
polarization. As the beam passes through the same quarter-waveplate, it changes to
linearly polarized again, but with a direction orthogonal to the original laser beam. The
beam is then reflected by the polarized beam splitter and collected by an imaging
receiver. The distance from the CCR to the imaging lens has to be small enough to allow
the lens to collect the refraction beam within the interested range of angles, and long
enough to have the refraction pattern considered to be collected at the far field.
Laser
Lens
CCR
Imaging Receiver
¼ Waveplate
Polarized Beam Splitter
Laser
Lens
CCR
Imaging Receiver
¼ Waveplate
Polarized Beam Splitter
Figure 2-9. Optical setup designed to separate the incoming light and the outgoing
light retro-reflected by an unactuated CCR. The far-field diffraction
pattern of the CCR is collected by the imaging receiver.
Figure 2-10 (a) shows the measured far-field diffraction pattern of an unactuated
CCR, with illumination along the body diagonal direction, while Figure 2-10 (b) presents
the simulated diffraction pattern for a perfect CCR of the same size [41]. The wavelength
of the illumination light is 632.8 nm. Both measured and simulated patterns exhibit
similar “star” patterns, corresponding to an effective reflecting area that is a six-sided
21
MEMS CORNER CUBE RETROREFLECTORS
polygon. The angular separation between nulls is 1.2 mrad in the experiment, and 1.0
mrad in the simulation, showing good agreement. The experimental results demonstrate
that any angular misalignment between the mirrors must be smaller than 1 mrad, or else
we would not be able to observe the diffraction pattern with null spacing on the order of 1
mrad.
1.2 mrad 1 mrad1.2 mrad 1 mrad
Figure 2-10. Far-field patterns of light reflected from CCR show good alignment
between the three mirrors of the CCR. Left: experimental result for a
fabricated device; Right: theoretical result for a perfect CCR of the
same size.
The collinear DSCS (CDSCS) is defined as the value of the DSCS when the
directions of illumination and observation are collinear, i.e., . The CDSCS is
relevant because in CCR-based links, the receiver is usually placed along the axis of
illumination. If the distance L is sufficiently large, then the receiver subtends a small
solid angle Ω
io nn ˆˆ −=
o, over which the DSCS is approximately equal to the CDSCS. Under these
assumptions, the received power Po can be computed approximately using
22
MEMS CORNER CUBE RETROREFLECTORS
oiio
io nnddIP Ω⋅−Ω
⋅≈ )ˆ,ˆ(σ (2-5)
For example, if a CCR consists of three identical square mirrors having side length a and
reflectivity rm, and is illuminated along the body diagonal by light at wavelength λ, the
CDSCS is
2
343))1,1,1(
31),1,1,1(
31(
λ
σ m
o
radd
=−Ω
(2-6)
In (2-6), we see that the CDSCS is proportional to the power captured by the CCR (a
factor a2) and the power reflected in three bounces from the mirrors (a factor ), and is
inversely proportional to the solid angle into which light is diffracted from the CCR (a
factor λ
3mr
2/a2).
At a wavelength of 632.8 nm, uncoated silicon has a reflectivity of approximately 0.3,
whereas gold has a reflectivity of 0.99. For an ideal CCR with a 250 µm bottom mirror
and 450 µm side mirrors1 illuminated along the body diagonal, Fraunhofer diffraction
theory predicts CDSCS values of 1.2 × 10−3 m2/sr and 4.4× 10−2 m2/sr for uncoated and
gold-coated devices, respectively. We have experimentally measured CDSCS values of
9.3 × 10−4 m2/sr and 2.8× 10−2 m2/sr, for uncoated and gold-coated devices, respectively.
These measured values are close to the theoretical predictions, further confirming the
near-ideal optical quality of the fabricated CCRs.
We have realized free-space optical communication over a range of 180 m. As shown
in the optical setup of Figure 2-11, a continuous-wave laser (CW) beam with 632.8 nm
wavelength, 0.8 mW power and 0.1 mrad divergence (half-angle) is directed towards
23
1 In devices fabricated to date, the dimensions of the side mirror are slightly larger than those of the bottom mirror because the bottom mirror is minimized to minimize layout area.
MEMS CORNER CUBE RETROREFLECTORS
CCR by a small mirror placed in front of the telescope. The telescope has an entrance
aperture of 8 cm diameter, subtending a half-angle of 0.22 mrad at the CCR. When the
CCR bottom mirror is not actuated, the beam reflected back to the telescope has a
divergence (half-angle) of 0.7 mrad; when the mirror is deflected by 5.7 mrad, this
reflected beam splits apart into two beams, each directed 11.4 mrad away from the optical
axis, well away from the telescope entrance aperture. As the size of the directing mirror
in front of the telescope is small compared to the aperture of the telescope, the amount of
light signal blocked by the directing mirror is minimal compared to the amount of signal
collected by the telescope. The CCR is driven by a pseudo-random, non-return-to-zero bit
sequence at 400 b/s. Light collected by the telescope passes through an optical bandpass
filter having 632.8 nm center wavelength and 10 nm bandwidth, and is imaged onto a
silicon photodiode with dimensions of 0.81 mm × 1.37 mm, which is coupled to a
transimpedance amplifier.
The detected optical signal matched with the transmitted bit pattern after a free space
transmission of 180 meters, as depicted in Figure 2-12. The modulated signal is received
with high SNR (> 22.3 dB), although its amplitude fluctuates slowly due to air turbulence
in the optical path.
24
MEMS CORNER CUBE RETROREFLECTORS
Oscilloscope Laser
Photo DetectorCCR
Telescope Lens
Uplink DataInL
Bandpass Filter
Oscilloscope Laser
Photo DetectorCCR
Telescope Lens
Uplink DataInL
Bandpass Filter
Figure 2-11. Optical setup for uplink free-space optical communication using a CCR
as a passive transmitter.
Figure 2-12. Detected 400 b/s signal after free-space transmission over 180 m.
Waveform 1: CCR drive signal; Waveform 2: detected photocurrent,
which is proportional to the intensity reflected from CCR.
It is also interesting to see the detected optical signal after a free space transmission
of 180 meters over a longer time, as depicted in Figure 2-13. The pseudo-random
generated signal is propagated to the receiver with a large amplitude variation and the
25
MEMS CORNER CUBE RETROREFLECTORS
SNR between the most intensified and weakest signals differs by about 10 dB. The
amplitude fluctuation of the received signal is due to the atmospheric turbulence when
the beam transmits from the laser to the CCR and from the CCR to the receiver.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0 1 2 3 4 5Time (sec)
Am
plitu
de o
f Sig
nal (
a.u.
6
)
Figure 2-13. Detected signal at 800 bit/s after free-space transmission over 180 m
for a longer period of time.
Studies over atmospheric turbulence show that turbulence-induced fading can be
reduced substantially by aperture averaging when the receiver aperture is larger than the
correlation length [42] (~ 1806328.0 ×=Lλ mm = 10.7 mm in our case). Therefore,
most of the detected signal variation is contributed from the limited size of the
transmitting CCR since the lens of the light receiver is much bigger than the correlation
length of intensity fluctuations. Besides making a compromise between the signal level
and the size of the Smart Dust mote for some extreme conditions, an alternative solution
26
MEMS CORNER CUBE RETROREFLECTORS
is increasing the power of the interrogating laser beam so that the received signal
achieves the desired SNR.
2.4. Signal-to-Noise Ratio Analysis of CCR-Based Links
In this section, we present an analysis of the SNR of free-space optical links using
CCR transmitters, to identify critical design parameters and aid in design optimization.
Here, we neglect the effects of atmospheric turbulence. These effects may be negligible
for short-range indoor links. For outdoor links with ranges up to a few hundred meters,
turbulence-induced intensity fluctuations may often be overcome simply by an increase
in transmitted power, as in the example of Figure 2-12.
Our analysis considers a system design as in Figure 2-11. A CW laser beam with
power Pi and divergence half-angle θi, is incident on the CCR from a range L. The
intensity Ii, incident on the CCR is
i
ii
LP
Iθπ 22 tan
= (2-7)
The telescope has light collection area Ac. We assume that L is sufficiently large, and that
Ac is sufficiently small, that the intensity of light reflected from the CCR is constant over
the telescope aperture. Since the telescope subtends a solid angle Ωo = Ac /L2 at the CCR,
using (2-7), the telescope collects a signal power
)ˆ,ˆ(tan 24 ii
oi
cisig nn
dd
LAP
P −Ω
=σ
θπ (2-8)
when the CCR is not actuated (logical ‘1’). The telescope is assumed to collect negligible
signal power when the CCR is actuated (logical ‘0’). Assuming the photodetector has
responsivity R, when the CCR is not actuated (logical ‘1’), the signal photocurrent is
27
MEMS CORNER CUBE RETROREFLECTORS
)ˆ,ˆ(tan 24 ii
oi
cisig nn
dd
LRAP
i −Ω
=σ
θπ (2-9)
Hereafter, for concreteness, we assume that the CCR consists of three identical square
mirrors having side length a and reflectivity rm, and is illuminated along the body
diagonal by light at wavelength λ. In this case, the CDSCS is given by Equation (2-6).
Thus, the signal photocurrent when the CCR is unactuated (logical ‘1’) is given by
i
cmisig
LRAraP
iθπλ 242
34
tan3
= (2-10)
Note that the signal photocurrent is proportional to the laser power Pi. Because the beam
is subject to diffractive spreading when propagating both to and from the CCR, the
photocurrent depends on the transmission range as L−4, instead of the L−2 dependence
usually observed in free-space optical links. The photocurrent depends on mirror size as
a4, mirror reflectivity as and on wavelength as λ3mr
−2, for reasons explained previously.
We now calculate the ambient light noise received by the photodetector. Suppose that
the photodetector has area Ad, and that the telescope has focal length f. The area in the
CCR plane “seen” by the photodetector is
2
2
fLA
A df = (2-11)
Assume that the region surrounding the CCR is illuminated by ambient light having
spectral density pbg (this quantity represents power per unit area per unit wavelength, and
has units of W/(m2⋅nm)), and that this region reflects ambient light with reflectivity rbg.
Suppose that the telescope employs an optical bandpass filter having bandwidth ∆λ.
28
MEMS CORNER CUBE RETROREFLECTORS
Within the filter bandwidth, the total ambient light power reflected from the region
“seen” by the photodetector is
2
2
f
LArpARpP dbgbg
fbgbgbgλ
λ∆
=∆= (2 12)
Assuming that the region surrounding the CCR is a Lambertian reflector [43], the power
Pbg results in an irradiance at the telescope of
22 f
Arp
L
PI dbgbgbg
bgπ
λ
π
∆== (2-13)
Hence, the ambient light-induced photocurrent is
2f
RAArpRAIi cdbgbg
cbgbgπ
λ∆== (2-14)
Note that the ambient light photocurrent is independent of the transmission range L, but is
proportional to the photodetector area Ad and to the telescope light-collection area Ac. In
order to minimize ambient light noise, it is desirable to choose the photodetector to be
only as large as required to capture the entire CCR image.
We assume that a preamplifier is employed to amplify the received photocurrent, and
will refer all noises to the preamplifier input. The ambient light induces white shot noise,
which has a (one-sided) power spectral density (PSD) given by
bgbg qiS 2= (2-15)
Additional noises may be contributed by the preamplifier. A feedback or load resistance
RF will contribute white noise having PSD F
BR R
TkS
4= , where kB is Boltzmann’s constant
and T is absolute temperature. The preamplifier transistors are assumed to contribute
white noise with PSD Samp. Assume that the preamplifier (or a following lowpass filter)
29
MEMS CORNER CUBE RETROREFLECTORS
limits the noise bandwidth to a (one-sided) bandwidth B, where B is approximately equal
to the bit rate. Then the total noise variance is given by
(2-16) BSSS ampRbgtot )(2 ++=σ
The peak electrical SNR is
2
2
tot
sigiSNR
σ= (2-17)
Assuming that all noise sources are Gaussian distributed, the bit-error probability is
given by
⎟⎟⎠
⎞⎜⎜⎝
⎛=
2SNRQPb (2-18)
where ⎟⎟⎠
⎞⎜⎜⎝
⎛=
2erfc
21)( xxQ . Achieving a bit-error probability of 10−6 requires a peak SNR
of about 19.5 dB.
Table 2-1 summarizes the symbols used during the SNR analysis of CCR-based links
and lists their experimental values in the communication test over a range of 180 m. The
signal power reflected by CCRs is calculated through the measured DSCS, about 67% of
the one reflected by a perfect CCR with similar sizes. The noise is dominated by the
white noise from the loading resistor as the experiment is conducted indoor and the
ambient light is low in amplitude. The analysis gives a SNR of 24.3 dB, agreeing with the
experimental SNR of 22.3 dB.
Symbol Parameter Value
Pi Laser power 0.8 mW
θi Laser divergence half-angle 0.1 mrad
λ Laser wavelength 0.633 µm
30
MEMS CORNER CUBE RETROREFLECTORS
L Communication range 180 m
Ii Light intensity incident on the CCR 7.86×10-3 W/m2
Ac Light collection area of the receiving telescope 5.03×10-3 m2
f Focal length of the telescope 0.4 m
DSCS Measured differential scattering cross section of the CCR with a 500 µm bottom mirror and 600 µm side mirrors
0.108 m2
Psig Signal power collected by the telescope when CCR is not actuated
1.32×10-10 W
R Responsivity of the photodetector at wavelength λ 0.3 A/W
isig Signal photocurrent when CCR is not actuated 3.96×10-11 A
Ad Receiving area of the photodetector 1.1×10-6 m2
Af Area of the field viewable by the photodetector 0.22 m2
pbg Spectral density of the ambient light ~10-5 W/m2/nm
rbg Reflectivity of the background which CCR is sitting on 0.3
∆λ Bandwidth of optical bandpass filter at the receiving end 10 nm
Pbg Ambient light power reflected from the region “seen” by the photodetector
6.6×10-6 W
Ibg Intensity of the ambient light collected by the telescope 6.48×10-11 W/m2
ibg Photocurrent induced by the ambient light 1.95×10-11 A
Sbg Power spectral density of the white shot noise induced by the ambient light and signal light
2.00×10-29 A2/Hz
SR Power spectral density of the white noise contributed by the load resistance RF (=20 MΩ)
5.62×10-27 A2/Hz
Samp Power spectral density of the white noise contributed by the preamplifier transistors
1.44×10-28 A2/Hz
B Bandwidth of the preamplifier or the following lowpass filter
1000 Hz
σtot Total noise variance 2.40×10-12 A
SNR Peak electrical signal-to-noise ratio 24.3 dB
Table 2-1. Symbols used during the SNR analysis of CCR-based links and their
experimental values in the communication test over a range of 180 m.
31
MEMS CORNER CUBE RETROREFLECTORS
Figure 2-14 plots the relationship between the interrogating laser power Pi and the
maximum transmission range L, assuming a bit-error probability Pb = 10−6, for different
values of the CCR side length a. Here a perfect CCR with three equal-sized square
mirrors is assumed for the simplicity of the analysis. The transmitted bit rate is 1 kb/s. All
other important parameters, such as interrogating beam divergence, collecting lens
aperture, photodiode dimensions, bandwidth of the transimpedance amplifier, and
feedback resistance, are assumed to be the same as those in the free-space communication
experiment, listed in Table 2-1. One significant change over the analysis from the
experiment is that the communication link is assumed to be established under sun light
instead of indoors. Therefore the shot noise from the ambient light is no longer
negligible. It contributes approximately the same amount of noise as the thermal noise
from the feedback resistor, while amplifier noise is still small enough to be ignored
during the analysis. As illustrated in the Figure 2-14, the maximum transmission range L
depends on the laser power as 41−iP , and depends linearly on the CCR side length a.
Figure 2-14 demonstrates that a CCR-based link of several hundred meters range is
feasible.
32
MEMS CORNER CUBE RETROREFLECTORS
0 2 4 6 8 100
500
1000
1500
2000
2500
Interrogating Laser Power Pi (mW)
Com
mun
icat
ion
Ran
ge L
(m)
0.25 mm
0.5 mm
0.75 mm
CCR Side Length: 1 mm
0 2 4 6 8 100
500
1000
1500
2000
2500
Interrogating Laser Power Pi (mW)
Com
mun
icat
ion
Ran
ge L
(m)
0.25 mm
0.5 mm
0.75 mm
CCR Side Length: 1 mm
Figure 2-14. Communication range L vs. interrogating laser power Pi required to
achieve a bit-error probability Pb of 10-6 for different CCR side lengths
(assuming that the CCR consists of three equal-sized square mirrors).
The communication link is assumed to be established under the
sunlight.
2.5. Integration into Sensor Nodes
Micromachined CCRs have been packaged with other components of Smart Dust
“motes”, i.e., solar cell, 1 Mb/s CMOS optical receiver, finite-state machine counter, low-
power ADC, accelerometer, and light-level sensor, to form a 16 mm3 autonomous solar-
powered sensor mote [14], as shown in Figure 2-15. Each mote consists of three dies, a
0.25 µm CMOS ASIC die, a 2.6 mm2 SOI solar cell array chip, and a MEMS four-
quadrant CCR die. The mote has successfully sampled photosensor data and transmitted
33
MEMS CORNER CUBE RETROREFLECTORS
it over the optical link with the CCR under the illumination of one sun, or under
incandescent or LED illumination of equivalent intensity.
Solar Cell Array
CCRs
XLCMOS
IC
Solar Cell Array
CCRs
XLCMOS
IC
Figure 2-15. 16 mm3 solar-powered Smart Dust mote with bi-directional optical
communication. Components include a multi-junction solar power
array, 1 Mb/s optical receiver, CCR as an optical transmitter, 8-bit
ADC, digital controller, accelerometer and light-level sensor.
In the Smart Dust communication architecture, a single base station transmits
commands and queries to a collection of motes via a broadcast free-space optical
downlink at bit rate up to 1 Mb/s. The base station also illuminates the CCRs and uses a
telescope and photodiode to receive messages transmitted via the CCR-based uplink at a
bit rate approximately 180 b/s. If the base station is equipped with an imaging receiver
incorporating multiple pixels, it can decode uplink messages transmitted simultaneously
and without synchronization by multiple dust motes, a form of space-division
multiplexing.
Figure 2-16 shows a signal transmitted by a CCR and received by a base-station
receiver. The 8-bit data packets alternately transmit data sensed by the accelerometer and
34
MEMS CORNER CUBE RETROREFLECTORS
light-level sensor. Data packets are separated by a stop bit ‘0’ and a start bit ‘1’. The
asynchronous transmission data rate is approximately 182 bit/s, and is determined by the
clock frequency of the internal oscillator in the ASIC chip.
Figure 2-16. Detected data packets transmitted at 182 bit/s by the modulation of the
CCR on a Smart Dust mote and received by a photodiode detector.
Start (‘1’) and stop (‘0’) bits from each packet are highlighted.
35
A more compact version of Smart Dust mote is displayed in Figure 2-17. It consists
of only two chips, one ASIC chip and one ICARUS die with CCRs, solar cells and an
accelerometer fabricated through a single process, ICARUS process [44]. ICARUS
process fabricates CMOS circuits and DRIE structures on an SOI wafer with filled
trenches isolating structures electrically [44]. The CCRs fabricated in ICARUS process
contains the same assembled side mirrors, except that there is no backside holes under the
actuated bottom mirror. The mirror is electrically divided into two parts by an isolation
trench close to the center of the mirror. One side of the mirror is connected to an
actuation voltage while the other side is electrically grounded, sharing the same voltage
MEMS CORNER CUBE RETROREFLECTORS
potential as the substrate. As the actuation voltage is applied, an electrostatic force is
generated on the side which the actuation voltage is applied on while there is no force
acting on the other side. Therefore a torque is created and rotates the micromirror.
Figure 2-17. SEM of the 6.6 mm3 Smart Dust mote, a two-chip assembly. CCRs are
fabricated in ICARUS process which also fabricates solar cells,
accelerometers, and NMOS buffers.
One advantage of ICARUS CCRs is that the settling time during which the actuated
mirror is released from its snap-in position to its resting position is found to be
significantly shorter, compared to CCRs fabricated from the previous process. This
improvement is attributed to the presence of squeeze film damping when the mirror is
released from its snap-in position. In the earlier process, the substrate wafer was removed
from underneath one half of the mirror so that no significant film damping is present
during the release of the mirror. However, for ICARUS CCRs, the handle wafer is
present underneath the entire mirror, so there is a significant amount of damping during
36
MEMS CORNER CUBE RETROREFLECTORS
both the snap-in and release of the mirror. A shorter settling time means a faster
modulating rate of the mirror and therefore CCRs can transmit a signal at approximately
its resonance frequency without adding complicated feedback control.
37
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
3. MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER
BONDING PROCESS
Scanning micromirrors are proposed to steer the laser beam in order to establish free-
space optical communication links between two small unmanned aerial vehicles for the
Steered Agile Laser Transmitter project [6]. Micromirrors are responsible for pointing,
tracking, and transmitting the modulated laser beam.
Two 1.5 m wingspan MLB Bats [45] serve as the aerial platform for the
communication system. They fly with a pre-designed spiral pattern, or in other words,
they know roughly the relative position of the other airplane. But an onboard micromirror
is needed to cancel the angular vibrations present on each airplane and steer the laser
beam within a range of angles in order to achieve the precise location of the other
airplane. The angular vibration of the small airplane can be as large as ± 5° and an extra ±
5° margin is provided in the design of the beam steering mirror to accommodate the
acquisition of optical links. A closed-loop control of the micromirror will be employed to
improve its switching ability, making a transition time between positions around the
order of 100 µs. Also the micromirror needs to have strong shock resistance since the
landing acceleration for a UAV is approximately 10 ~ 15 g.
Electrostatic comb drive actuator is the preferred scheme for actuating scanning
micromirrors over other methods, such as electromagnetic, thermal, or piezoelectric
actuators, because electrostatic actuators offer faster transition capability and lower
power consumption. These properties are essential for the micromirrors to maintain the
38
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
optical link with the target and operate on a UAV where miniaturizing and fuel saving are
aggressively pursued. Moreover, the required feedback signal for controlling a
micromirror can be implemented by just including a group of sensing fingers directly on
the electrostatic comb drive actuator.
3.1. Design of Scanning Micromirrors Using Lateral Actuation
Our group introduced the method of realizing scanning micromirrors by utilizing a
lateral comb drive actuator [38]. As shown in Figure 3-1, the bi-directional force
generated by a lateral comb drive actuator is transferred as an off-axis torque over two
torsional beams by two transfer arms.
Lateral Force
Low-Mass Mirror
Transfer Arm
Two Anchored Torsional Beams
Lateral Force
Low-Mass Mirror
Transfer Arm
Two Anchored Torsional Beams
Figure 3-1. Torsional movement of scanning micromirrors is realized by an off-
axis lateral force generated from a lateral comb drive actuator.
An obvious benefit of this scheme is the separation of the micromirror and the
actuator which provides more flexibility to the design. A large actuator can be designed
to extend to both in-plane directions of the layout and all comb fingers always add equal
amount of moment of inertia to the device. The DC scanning range of a lateral actuated
39
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
micromirror can be very large since it is limited only by the maximum stress that the
material of the device can sustain while the range of a micromirror with a vertical/angular
actuator is limited by the height-to-length ratio of the comb drive finger which is often
compromised by having long fingers to provide enough torque. The lateral actuation
design offers more shock resistance, too. The lateral movement of the device is resisted
both by the torsional beams and actuator suspension beams, in contrast to single torsional
beam suspension when using a vertical comb drive actuator.
3.2. SOI/SOI Wafer Bonding Process
This multilevel design was formerly fabricated on an SOI wafer using a combination
of timed DRIE etching and DRIE etching with etch stops. However, timed etching does
not produce uniform structures across the wafer and therefore needs careful monitoring.
A new approach, SOI/SOI wafer fusion bonding, is introduced to attain multilevel
structures with well-controlled thickness.
In the proposed new process a patterned third layer is aligned and bonded onto a
patterned SOI wafer, producing 3D devices or stacked high-aspect-ratio structures. The
third layer comes from the device layer of another SOI wafer [46][47][48], with a choice
of thickness as small as 2 µm and a thickness uniformity of ± 0.5 µm, whereas structures
fabricated by the timed etching counterpart can have a thickness variation of 5 µm across
a wafer. The sacrificial handle wafer of the bonded SOI wafer can be disposed of by
either plasma blank etching or mechanical grinding. When the handle wafer is left with
the desired thickness, a subsequent polishing step can provide another layer to the stack.
Then more layers can continue to be added on by wafer fusion bonding, constructing
multi-layer structures. One drawback of this layer stacking strategy is that bonding gets
40
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
more difficult as the stresses in the stacked layers induce more bow and warpage over the
wafer. Besides stacking several levels of high-aspect-ratio structures, silicon fusion
bonding introduces little or no thermal stress because of the well-matched thermal
expansion between the bonded layers and the fabricated monolithic single crystal
structures are completely compatible with subsequent high-temperature process steps,
such as oxidation and diffusion.
In addition to allowing tighter control over the thicknesses of the critical layers, the
improvement of fabricating scanning micromirrors using this new bonding process
includes producing at a higher yield, obtaining a functional two-axis scanning
micromirror, and scanning at a larger angle with a smaller actuation voltage.
3.2.1. Bonding mechanism
When two mirror-polished and cleaned silicon wafers are brought closely, they are
immediately bonded with each other [49]. After the bonded pair is brought into a furnace
and annealed for a certain time, the bonds across the interface are strengthened and two
silicon wafers are fusion-bonded with each other. The proposed SOI/SOI wafer bonding
process is to employ this adhesion property between silicon, creating a monolithic multi-
level device, whose thickness is strictly controlled.
Understanding the bonding mechanism helps us in optimizing the process flow and
choosing the recipe parameters. The following is a compendium of research results
regarding to the bonding procedure and its chemistry [50][51][52]. Prior to bonding,
polished silicon wafers are chemically treated so that the wafer surface is terminated with
a high density of silanol groups (Si-OH). These groups are covered with several mono-
layers of water. When the two wafers are brought into intimate contact, an immediate
41
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
weak bond occurs due to the hydrogen bonding between the OH groups on the two wafer
surfaces. The bonded wafer pair is then annealed in a furnace. First at a temperature
below approximately 300°C, silanol bonds are converted to siloxane bonds (Si-O-Si):
Si-OH + OH-Si -> Si-O-Si + H2O (3-1)
The resulting water diffuses into the silicon crystal to form silicon dioxide:
Si + 2 H2O -> SiO2 + 2 H2 (3-2)
When temperature exceeds 800°C, silicon oxide begins to flow, fill up the interface
micro-gaps, and form strong siloxane bonds all over the wafer.
Therefore, the primary condition to achieve the bonding between two silicon wafers
is a clean and flat wafer surface, making the contact area as large as possible. An
annealing temperature higher than 800°C is also preferred since at that temperature the
glass layer on the bonding interface starts to reflow and the achieved bond strength is
comparable to that of single crystal silicon. In practice, a conservative annealing
temperature of 1150°C is used to ensure that the process works. Methods, such as oxygen
plasma activation and/or tetramethoxysilane (TMOS) solution dip [50], can be adopted
later to decrease the annealing temperature (≤ 500°C) while still achieving bonding
energies that are sufficiently high for a micromechanical device.
3.2.2. Minimizing bow for SOI wafers
It has been experimentally observed that in order to achieve a secure silicon-silicon
bonding, the roughness of wafer surface has to be less than 1 nm and the bow of a 4-inch
wafer is no greater than 5 µm [53]. Our experiments show that two wafers with a bow as
large as 25 µm can be bonded without problems. However, an SOI wafer from our
42
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
vendor, BCO Technologies, has a typical bow of 75 µm, preventing an adequate bonding
between SOI wafers. Strategies are needed to flatten wafers and increase the yield of
bonding.
The bow of an SOI wafer is mainly induced by the mismatch of thermal expansion
coefficient between silicon and oxide, causing excess mechanical stresses in the SOI
wafer after annealing at elevated temperatures and subsequent cooling. At high annealing
temperature, there is no internal stress between the silicon and oxide layers due to the
reflow ability of the oxide layer. As temperature drops, oxide contracts but silicon shrinks
more. Therefore, the thermal mismatch between silicon and oxide builds up internal
stress and cause the wafer to bend, as shown in Figure 3-2. A simple model to calculate
the bending caused by the thermal stress is presented in [54] and described in the
following. From the basic principle of mechanics, the stress in the films must obey the
following conditions:
(1) Force balance:
(3-3) ∑=
=N
iiF
10
where Fi is the normal force acted on layer i and N is the number of layers.
(2) Moment balance:
0212
'1
1
11
3
=⎟⎟⎠
⎞⎜⎜⎝
⎛++∑ ∑∑
=
−
==
N
i
i
j
iji
N
i
ii ttFtEρ
(3-4)
where Ei’ is the planar modulus for layer i, ti is the thickness of layer i, and ρ is the radius
of wafer curvature.
(3) Interface strain continuity for any two adjacent layers:
43
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
ρ
αρ
α2'2'
1
11
11
+
++
++ −+∆=++∆ i
ii
ii
i
ii
ii
ttE
FTttE
FT (3-5)
where αi is the thermal expansion coefficient of layer i and ∆T is the temperature
difference between the annealing temperature and room temperature.
F1, t1, α1F2, t2, α2
Fi, ti, αi
SCS Wet oxide
F1, t1, α1F2, t2, α2
Fi, ti, αi
F1, t1, α1F2, t2, α2
Fi, ti, αi
SCS Wet oxide Figure 3-2. An SOI wafer is curved by residual stresses. Fi, ti, and αi are the normal
force, thickness, and thermal expansion coefficient of layer i.
According to this simple model, there are several ways to reduce the bow in an SOI
wafer:
(1) Reduce the thickness of the buried oxide layer. This idea is not practical because a
certain thickness of oxide layer (preferably 2 µm) is required in order to keep the
parasitic capacitance of the bonding pads and inter-connection wires small for the
feedback control of mirror positions. However, a step of timed-etching the exposed oxide
to a thinner thickness can be added between the DRIE etching of the device layer and the
bonding of the two wafers in order to reduce the wafer stress. 10:1 HF should be used for
this purpose because compared to 49% HF, its etching speed is slow enough to strictly
control the remaining oxide to be thick enough for acting as the etching stop for the later
DRIE etching. In this way, a thinner oxide film is left in the exposed area to reduce the
stress while a 2 µm-thick oxide layer is remained under the bonding pads and inter-
connection wires to maintain the low parasitic capacitance.
44
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
(2) Increase the thickness of the handle wafer. This is not a good solution, either,
since a thicker wafer presents more difficulty in accommodating the bending and makes
the bonding harder to achieve.
Figure 3-3. Add an oxide layer onto the back of the handle wafer of SOI wafers
to balance the stress and obtain a flatter surface.
SCS Wet oxideSCS Wet oxide
(3) Retain an oxide layer on the backside of the handle wafer. The sandwiched
structures, as shown in Figure 3-3, are able to balance the stress and obtain a flatter
surface. One thing to be noted is that any non-uniformity in the stress distribution might
introduce warpage to the multi-layered wafer. But the device layer of the SOI wafer is
etched by repeating the same pattern and the thickness of the added oxide layer is
uniform across the wafer. As a result, the local residual stress is expected to be minimal
to produce any significant warpage to the wafer.
45
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Bow
of W
afer
(µm
)
0 0.5 1 1.5 2
-100
0
100
200
300
Thickness of Oxide on the Backside of the Wafer (µm)
Bow = 0
Bow
of W
afer
(µm
)
0 0.5 1 1.5 2
-100
0
100
200
300
Thickness of Oxide on the Backside of the Wafer (µm)
Bow = 0
Figure 3-4. The bow of the multilayer wafer is varied with the thickness of the
oxide layer added on the backside of a 50 µm/2 µm/350 µm SOI wafer.
Simulation shows a 1.5 µm-thick oxide layer optimizes the wafer
flatness.
The previously described stress-flatness model is used to find the proper oxide
thickness in order to obtain the flattest wafer. As illustrated in Figure 3-4, the bow of the
SOI wafer (with a 50 µm-thick device layer, a 2 µm-thick buried oxide layer, and a 350
µm-thick handle layer) is varied with the oxide thickness added on the backside of the
wafer. The simulation shows that a 1.5 µm-thick oxide layer makes the bow of the SOI
wafer zero and optimizes the flatness of the wafer. In experiment, an unprocessed SOI
wafer with the same thickness configurations has a bow of 76.3 µm initially. After
thermally growing a 1.5 µm-thick oxide layer on both sides of the SOI wafer and
46
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
removing the front side oxide layer, the bow of the SOI wafer became 17.8 µm, which is
small enough to allow a successful bonding with other SOI wafers.
3.2.3. Strategies to enhance bonding
Surface cleanness is another significant condition for successful wafer fusion bonding.
The initial hydrogen bonding that pre-bonds two wafers are weak and operates over a
short range, only when the two wafers are very close together. Therefore, having wafers
flat and free with particles are critical prior to bonding.
Several steps were practiced to ensure a strong adhesion force between the two
patterned SOI wafers. First, the design of the layout allocated about 50% of the wafer
surface as contact area to guarantee adequate force. Second, wafers were handled
carefully in the clean room. For example, a vacuum pen was used to grab a wafer on its
backside whenever applicable, as particles or scratches that can destroy a bond might be
introduced to the bonding surface of the wafer if using metal tweezers. Third, a layer of
thermal oxide was grown on the wafers as the first step of the process and was stripped
off just before cleaning and bonding occurred. This thermal oxide layer provides
protection throughout the wafer handling and is a common practice to be added in the
bonding process by researchers. Fourth, as suggested in the previous section, an oxide
layer was retained on the backside of the SOI wafers to balance the stress introduced by
the buried oxide layer in an SOI wafer. These sandwiched layers produce flatter wafers,
making bonding easier. Lastly, a series of chemical cleaning steps were carried out
during which a layer of hydrous thin oxide grew on the wafer surface. The hydrous oxide
is highly reactive and wafers with this hydrophilic surface are ready to bond at room
temperature.
47
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
It is also suggested by colleagues that the residual polymer film from the passivation
cycles during DRIE etching degrades the bonding surface and thus its complete removal
is important. Since this polymer film is stubborn and HF, piranha and RCA cleaning are
not sufficient, O2 plasma ashing for over 1 hour is recommended to completely remove
the film.
3.2.4. Detailed process flow
As shown in Figure 3-5, the process started with two SOI wafers, one with a 50 µm
thick device layer (we refer to it as the 50 µm SOI wafer) and the other with a 2 µm thick
device layer (we refer to it as the 2 µm SOI wafer). First, the device layers of the two SOI
wafers were patterned individually. After growing a thermal oxide layer with a thickness
of 3000 Å, the device layer of the 2 µm SOI wafer was patterned with DRIE etching. For
the 50 µm SOI wafer, a 1.5 µm-thick oxide layer was grown. The front side oxide is used
as a mask during the later DRIE etching while the backside oxide balances the stress in
the SOI wafer to achieve a flatter bonding surface. Then a timed DRIE etching step was
employed to obtain a layer including non-thickness-critical structures only, such as the
pushing/pulling arms for scanning micromirrors. This was done by patterning the front
side oxide layer first, depositing a layer of photoresist, patterning the deposited
photoresist, DRIE etching to a depth of 30 µm, peeling off the photoresist, and DRIE
etching until the exposed silicon structures were 6 µm high. Keeping an oxide layer on
top of the device layer during the DRIE etching is critical for protecting the bonding
surface since it is experimentally observed that the silicon surface exposed to DRIE
etching does not bond. Also note that two alignment marks were patterned on the
48
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
backside oxide layer of the 50 µm SOI wafer before the first DRIE etching. They are
bonding alignment marks as well as the lithography alignment marks for the substrate
patterning.
SOI wafer 1: 50 µm/2 µm/350 µmSOI wafer 2: 2 µm/1 µm/350 µm
Pattern two wafers individually
Alignment pre-bond by Karl Suss bonder, followed by 9 hours of annealing at 1150°C
STS DRIE etch handle wafers and release in HF
SCS Wet oxide
SOI wafer 1: 50 µm/2 µm/350 µmSOI wafer 2: 2 µm/1 µm/350 µm
Pattern two wafers individually
Alignment pre-bond by Karl Suss bonder, followed by 9 hours of annealing at 1150°C
STS DRIE etch handle wafers and release in HF
SOI wafer 1: 50 µm/2 µm/350 µmSOI wafer 2: 2 µm/1 µm/350 µm
Pattern two wafers individually
Alignment pre-bond by Karl Suss bonder, followed by 9 hours of annealing at 1150°C
STS DRIE etch handle wafers and release in HF
SCS Wet oxideSCS Wet oxide Figure 3-5. Process flow of fabricating scanning micromirrors using the
SOI/SOI wafer bonding process.
The next step was pre-bonding the two patterned SOI wafers with alignment and then
annealing the bonded wafer pair in a furnace. After stripping off the oxide layer on the
front side of the wafers in 10:1 HF, both patterned SOI wafers were cleaned in piranha,
modified RCA1, RCA2 with de-ionized water rinsing in between. Then the two cleaned
SOI wafers were aligned and pre-bonded by a Karl Suss BA6 bond aligner, followed by 9
49
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
hours of annealing at 1150°C in a furnace. An inspection using an IR microscope showed
a fully bonded wafer pair.
DRIE etching was then used to dispose of the top handle wafer partially and pattern
the substrate layer of the bonded wafer. With a protective layer of the top handle wafer
left, the bonded wafer pair was diced into several dies. The individual dies or group of
dies were DRIE etched to fully dispose of the top handle wafer afterwards. The dies were
then cleaned in Piranha and released in 5:1 buffered HF. It is extremely important to
clean first and release later as the HF dip before photoresist cleaning leaves polymer
residues on the chip, which are extremely difficult to get rid of and often causes the
electrical actuation of the micromirror to become non-functional. Finally the released
individual chip was wire-bonded and packaged.
3.3. Bond Characterization
3.3.1. Diagnosis of bonded structures by SEM and infrared images
The cross section of two bonded wafers can be seen using SEM after intentionally
broken into pieces, as shown in Figure 3-6. There is no discontinuity between two bonded
layers, indicating a solid bonding.
50
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
bonding interface bonding
interface
bonding interface bonding
interface
Figure 3-6. The cross section of bonded Si wafers with pre-patterned structures
shows continuity at bonded areas, indicating a solid bonding.
The bonding quality and alignment accuracy can also be monitored with an infrared
camera during the process. Since infrared light transmits through silicon, the well-bonded
area appears bright in the IR camera while areas with voids or etched patterns appear
dark. Two typical images of bonded wafers without voids and with one void are shown in
Figure 3-7. The dark circle in both images is a shadow in the optical path of the camera
and does not move with the wafers, so the dark circle does not represent the variation of
the bonding quality.
51
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
(a)
(b)
Figure 3-7. Infrared transmission images of bonded Si wafers without voids (a) and
with one void (b).
3.3.2. Electrical interconnection realized by bonded structures
The interface of bonded silicon wafers is generally not perfect at the atomic level, not
only in that the crystal orientations of two wafers are not strictly aligned, but also in that
52
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
species other than silicon atoms, such as siloxane bonds (Si-O-Si) and H2 molecules, are
often present on the interface. The electronic property of the bonding interfaces is
important for interconnecting two bonded layers electrically.
As shown in Figure 3-8, a group of bridge structures is fabricated to characterize the
electronic property between two bonded layers. It consists of a 2 µm-thick bridge
connecting two pads that are made of the 50 µm-thick layer. The resistivity of the bonded
2 µm-thick layer is 0.1~0.3 Ω-cm and the resistivity of the underlying 50 µm-thick layer
is 0.005~0.02 Ω-cm. Both the 2 µm-thick layer and the 50 µm-thick layer are p doped.
Two probes are pressed upon the two 50 µm-thick pads individually to measure the
electrical property of the bridge structure. Since the resistivity of the underlying 50 µm-
thick layer is much lower than that of the bonded 2 µm-thick layer, the current-voltage
relationship between two pads mainly depends on the dimensions of the 2 µm-thick
bridges and the two bonding interfaces at the two ends of the bridge.
53
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Figure 3-8. Testing structures to characterize the electronic property of the bonding
interfaces. A 2 µm-thick bridge connects two pads that are made of the
50 µm-thick layer. Note that there is a misalignment of 7 µm along the
horizontal direction between two bonded layers while no
misalignement along the vertical direction for this run.
Two typical current-voltage (IV) curves of the bonded bridge structures are shown in
Figure 3-9. The resistances for the short and long bridge structures, derived from the
slope of the IV curves, are 4.57 kΩ and 13.28 kΩ. It shows that two bonded structures
have an ohmic connection. The resistance ratio between the long bridge and short bridge,
2.90 in this case, corresponds to their length ratio, 3.0.
54
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
-2.5
-2
-1.5
-1
-0.50
0.5
1
1.5
2
2.5
-10 -5 0 5 10Voltage (V)
Cur
rent
(mA
)
short bridge 1
long bridge 1
Figure 3-9. Current-voltage curve of bonded bridges shows an ohmic inter-
connection between two bonded layers that are both p-doped.
Many other bonded bridges display a current-voltage relationship similar to the
curves in Figure 3-10. It is not strictly linear, although the resistance ratio between the
short bridge (resistance: 2.45 kΩ, derived from the slope of the curve) and long bridge
(resistance: 6.32 kΩ, derived from the slope of the curve) is 2.58, close to 3.0. It seems
that a potential barrier exists between the two bonded layers, possibly due to the lattice
defects and contaminants in the interface region. However, electrical interconnection is
still possible to be made through bonded layers, although it might present difficulty in
realizing the high-resolution control of the charge distributions since the magnitude of the
potential barrier varies from device to device. A closed-loop feedback control is a
possible solution to overcome the effect of this barrier voltage variance associated with
the bonded interface.
55
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
-2
-1
0
1
2
-10 -5 0 5 10Voltage (V)
Cur
rent
(mA
)
short bridge 2
long bridge 2
Figure 3-10. Current-voltage curve of bonded bridges shows an inter-connection
between two bonded layers that are both p-doped.
3.3.3. Shear stress test of bonded structures
A shear stress test is carried out to measure the bonding strength between two bonded
layers. As shown in Figure 3-11, a 2 µm-thick plate is bonded to an underlying 50 µm-
thick trunk. The size of the bonding area in the middle is about 100 µm × 40 µm. The
bonded structures are then suspended by four 2 µm-thick, 10 µm-wide, and 200 µm-long
suspension beams. The spring stiffness of these suspension beams can be easily
calculated through their dimensions. An in-plane force is exerted at the tip of the 50 µm-
thick plate in the direction perpendicular to the length of the suspension beams. The
displacement of the bonded structures under the applied probe force can be viewed
through the nearby ruler under a microscope.
56
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
50 µm-thick plate
2 µm-thick suspension beams
probe force
ruler
100 µm
50 µm-thick plate
2 µm-thick suspension beams
probe force
ruler
100 µm
Figure 3-11. A testing structure is designed to measure the bonding strength of two
bonded layers. Note that there is a misalignment of 13 µm along the
horizontal direction between two bonded layers while about 2 µm along
the vertical direction for this run.
As the probe force increases, two bonded layers are expected to show de-bonding
from each other as the shear stress acted on the bonded interface exceeds the ultimate
stress. Therefore the ultimate shear stress of the bonded layers can be obtained by
multiplying the spring constant of the suspension beams by the displacement of the
bonded layers at the de-bonding point. However, the strength test shows that when a
pushing force of about 1.0 mN is exerted, the structure breaks at the root of its suspension
beam, before the bonding fails. Thus only the lower limit of the ultimate shear stress,
which is approximately 0.25 MPa in this case, is obtained. Another testing structure gives
a lower limit of 1.01 MPa. Compared with the ultimate tensile stress of 9.0 ± 3.9 MPa
measured by a pulling test over two structured wafers bonded in another paper [55], our
numbers are low. But it is high enough to function as the linkage between the
57
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
micromirror and the transfer arms since the shear stress sustained by the bonded interface
is less than 1 MPa. In addition, the bonded wafers were found to withstand the post-
bonding steps, such as de-ionised water rinsing, spin drying, photo-lithography handling,
and chemical-mechanical polishing.
3.3.4. Air sealing by bonded structures
Circular cavities clamped on the edges are fabricated to test the sealing quality held
by bonded structures. The wafer bonding is carried out in a vacuum, leaving the pressure
inside the cavity lower than the ambient atmosphere. When the handle wafer of the
bonded wafer pair is released and the sealed cavity is exposed to the atmosphere, the
pressure difference between the inside air and the outside atmosphere displaces the
capping layer inward, as shown in Figure 3-12. Therefore a measurement over the
displacement profile of the capped layer can reveal the sealing and bonding quality held
by bonded structures.
If the maximum downward deflection, w, of the center of the edge-clamped circular
plate is bigger than the thickness of the capping layer, the large deflection theory is used
to calculate w. It is related to the pressure difference between the cavity and the
atmosphere, q, as the following expression [56]:
3/1
662.0 ⎟⎠⎞
⎜⎝⎛=
Etqaaw (3-6)
where a is the radius of the circular plate and t is the thickness of the capping plate, i.e.
the bonded layer. The pressure difference between the sealed cavity and the ambient
environment can thus be determined by measuring the deflection at the center of the
edge-clamped circular plate:
58
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
4
3
29.0 atEwq = (3-7)
Figure 3-12. Profile of a circular cavity clamped on the edges, measured by a Wyko
NT3300 interferometer.
If the maximum deflection is less than half the thickness of the capping layer, the
center deflection is reached under the assumption of small deflections as the following
equation:
( ) 3
421
163
Etqaw ν−= (3-8)
Then the pressure difference between the sealed cavity and the ambient environment
can thus be determined by:
( ) 42
3
1316
aEwtqν−
= (3-9)
59
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Figure 3-13. Deflection of a capping layer clamped on the edges, simulated by FEM
analysis.
The small deflection and large deflection assumptions give different relationships
between the center deflection, the thickness of the capping plate and the pressure if
comparing Equation (3-7) and Equation (3-9). Unfortunately the deflections of most
testing cavities are measured to be right on the boundary condition, i.e. the maximum
deflection is about half of the thickness of the capping layer. Therefore, a numerical
method using the large-displacement nonlinear analysis is employed to estimate the
pressure difference between the sealed cavity and the ambient atmosphere according to
the measured deflection and capping layer thickness. Figure 3-13 shows the deflection of
a capping plate that is simulated by Pro-mechanica, a commercial FEM program, using
the large-displacement nonlinear analysis.
60
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Table 3-1 shows the pressure inside the sealed cavity for several devices, numerically
calculated through Pro-mechanica. The average pressure calculated through the
deflection of the capping membrane is about 74.5 kPa with a standard deviation of 3.4
kPa. The variations in the calculated pressure come from the estimation of the thickness
of the capping plate. Since measuring the thickness right on the cavity is difficult, the
thickness is obtained by measuring the height of a nearby step formed by a bonded
structure, which is slightly different than the thickness of the capping plate.
Device
#
Thickness
of capping plate
t (µm)
Radius
of cavity
a (µm)
Displacement
at center
w (µm)
Pressure
in the cavity
pc (kPa)
1 2.24 100 0.28 69.4
2 2.24 150 1.17 71.2
3 2.24 200 2.37 74.6
4 2.34 100 0.23 71.1
5 2.34 150 0.98 74.1
6 2.34 200 2.12 77.0
7 2.39 100 0.17 77.4
8 2.39 150 0.80 78.2
9 2.39 200 2.03 77.4
Table 3-1. Numerically calculated pressure inside the sealed cavity.
The chamber vacuum of Karl SUSS bond aligner during the bonding is about 80 kPa,
according to the chamber pressure gauge on the front panel of the machine. Since the
chamber is flushed with N2 before bonding happens, the air enclosed by the sealed cavity
consists of N2 only and does not react with silicon. Therefore, the vacuum pressure given
by the pressure gauge agrees with the number calculated through the deflection of the
capping membrane.
61
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
3.4. Mechanical Modeling and ANSYS Simulation of Micromirrors
A mechanical model is established to show the bending of the pushing/pulling arm
and the rotation of the suspension beams under a lateral actuation force. First a
relationship between the actuation force and the actuated angle is obtained. Then the
working range of micromirrors under a static loading is calculated based on the
maximum principal stress criterion. Finally, the analytical result predicted by the model is
compared with the result calculated by ANSYS FEM simulation.
3.4.1. Analytical simulation
Unlike many other straightforward MEMS actuation mechanism, the analysis of
scanning micromirrors actuated by a lateral comb drive actuator is complicated by its
transfer mechanism. As a lateral force is exerted on the pushing/pulling arms, the arms
bend and the torsional beams rotate. The angle of rotation for the micromirror depends
not only on the strength of the actuation force, but also on the dimensions of the
pushing/pulling arms.
The case of pushing actuation is discussed first. As shown in Figure 3-14, two
pushing arms are combined into one and a linkage beam connects the pushing arm and
the torsional beams which are not shown in the figure. When applying a pushing force Fx
generated by a comb drive actuator on the left side, the pushing arm bends and the
torsional beams rotate around their central axis. The dashed lines represent the original
positions of the structures, while the solid lines stand for the displaced structures under
the comb-drive lateral force. The left side of the pushing arm is undergoing guided lateral
movement since the attached comb drive suspension beams are compliant to translation
along the pushing direction while opposed to the orthogonal movements. The top side of
62
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
the linkage beam is free to rotate, but resistant to any lateral movement. This is to assume
that the torsional beams, to which the linkage beam is attached, are robust to lateral
movements but compliant to rotation.
y
x
Fx
FyFx
MBMA
y
θFyt
Pushing Arm
Linkage Beam
Torsional Beam
y
x
Fx
FyFx
MBMA
y
θFyt
Pushing Arm
Linkage Beam
Torsional Beam
Figure 3-14. The cross section of the pushing arm and the rigid linkage beam under
the pushing force Fx generated by a lateral comb drive actuator. The
dashed lines represent the original position of the structures, while the
solid lines stand for the displaced structures under the comb-drive
lateral force.
The pushing arm is designed to be compliant whereas the linkage beam is rigid. As
the lateral force is loaded on the left side of the pushing arm, the arm bends and exerts Fx,
Fy, and MB on the linkage beam. In addition to the usual transverse load, the pushing
beam carries an axial compressive force. Axial compression increases the deflection and
bending moment produced by a transverse load. However, we cannot superpose the effect
of the axial load on the state produced by the transverse load alone. Instead, axial and
transverse loads must be considered simultaneously [57]. Universal beam theory still
applies to this problem since all the conditions that are assumed in the universal beam
theory are still satisfied, i.e., the deflection in the pushing arm is small compared with the
length of the arm, the plane section remains plane in the pushing arm, and no shear stress
63
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
is involved. The only difference between this case and the simple cantilever deflection is
that the bending moment induced by the axial load has to be taken into account besides
the moment caused by the transverse load.
Consider the bending moment induced by the axial force Fx in Figure 3-14. When the
lateral deflection y is zero, Fx is directed through the centroid of the cross section and
poses no moment to the pushing arm. When the pushing arm is deflected, Fx has a
moment arm of y about a point on the beam axis and produces a bending moment -Fxy.
Therefore, the standard moment-curvature relation of universal beam theory,
Mdx
ydEI =2
2
, becomes
yFxLFMdx
ydEI xyB −−+= )(2
2
(3-10)
where E is the modulus of silicon, I is the bending momentum of the pushing arm, MB is
the moment exerted by the linkage beam, Fy is the transverse force, L is the length of the
pushing beam, and x is the distance from the point to the left end of the pushing beam. Fx
is generated by the comb drive actuator and is constant throughout the beam. Fy and MB
are the only unknown parameters that need to be determined through the boundary
conditions.
The linkage beam is considered to be rigid and balanced by the forces and moments
from the pushing arm below and the torsional beams above, as shown in Figure 3-15.
Define MA’ to be the moment exerted by the torsional beams and MB’ by the pushing arm,
then we have
(3-11) 0)cos('' =−−− θθ tFtFMM yxBA
64
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
MB’
MA’Fx
Fy
Fx
Fyt θ
MB’
MA’Fx
Fy
Fx
Fyt θ
Figure 3-15. Rigid linkage beam balanced by the forces and moments from the
pushing beam below and the torsional beams above.
The counter moment of MA’ is the one that rotates the torsional beams, so we have
θθkM A =' (3-12)
where kθ is the rotational spring constant of the suspended torsional beams and θ is the
angle of rotation, which we are interested in solving. The torsional stiffness of the
torsional beams with a rectangular cross section can be expressed by a general equation
θ
θkT
KGTLt ==
2 (3-13)
where T is the applied torque, Lt is the length of the torsional beam, K is a factor
depending on the cross-section dimensions of the torsional beam, G is the shear modulus
of the material, and ‘2’ in the equation indicates two torsional beams suspending the
micromirror. Unlike torsional beams with a circular section, K of the torsional beams
with a rectangular cross section is a value less than the polar moment of inertia, J. The
approximated formula (error within 4%) of K for the torsional beams with a rectangular
cross section can be obtained through Saint-Venant’s method and is found to be [58]
⎥⎦
⎤⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−−= 4
43
12136.3
316
ab
ababK (3-14)
where 2a and 2b are the width and thickness of the rectangular section and satisfy a≥b.
65
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Using Equation (3-12) to rewrite Equation (3-11), we obtain
θθθθ tFtFkM yxB +−= )cos(' (3-15)
The first term is proportional to the angle of rotation, θ. Fx is the lateral force that
induces θ, so it is proportional to θ, too. As we count the first order of θ only, the second
term can be simplified to Fxt. As Fy is the transverse force induced by the rotation, it is
also a term proportional to the first order of θ. Thus the third term is a second order of θ
and can be neglected. Rewriting Equation (3-11), we get
tFkM xB −≈ θθ' (3-16)
As MB is the counter moment of MB’, combining this expression with Equation (3-10),
we get the equation that determines the displacement of the pushing arm:
)(2
2
xLFtFkyFdx
ydEI yxx −+−=+ θθ (3-17)
This is a second order differential equation and its solution consists of two parts. One
part is a general solution and the other part is a particular solution associated with the
right side of Equation (3-17):
)()cos()sin( 21 xLFF
FtFkkxckxcy
x
y
x
x −+−
+−=θθ (3-18)
where c1 and c2 are unknown constants and EIFk x= . As the left side of the pushing arm
is undergoing guided lateral movement and the linkage beam is only free to rotate, the
boundary conditions become
0)0( ==xy (3-19)
(3-20) 0)0(' ==xy x
66
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
0)( ≈= Lxy (3-21)
θ−== )(' Lxy x (3-22)
With four boundary conditions and four unknown parameters (θ, Fy, c1, and c2), we
can solve the angle of rotation to be
(( )
))sin(2)cos(2
)sin()cos(
2
kLkLkLkLkLkLkEIk
EItk
+−−
+=
θ
θ (3-23)
The relationship between the lateral force, Fx, and the angle of rotation, θ, is
apparently nonlinear. However for a small actuation force, we can simplify Equation (3-
23) into
LEIk
tFLEIk
EItk x
/4/4
2
+=
+≈
θθ
θ (3-24)
Or rewrite it in this way,
θθ ⎟⎠⎞
⎜⎝⎛ +≈
LEIktFx
4 (3-25)
The off-axis lateral actuation of a micromirror is simplified to a simple model in
which a torque is applied on a torsional spring, whose spring constant is contributed by
not only the torsional beams, but also the transfer arms.
The next step is to find out the maximum stress occurring on the pushing arm and the
torsional beams. According to Equation (3-17), the bending moment on the pushing arm
is
yFxLFtFkM xyx −−+−= )(θθ (3-26)
The last two terms vary with x, while the rest of the terms are fixed throughout the
beam. A plot of the bending moment vs. x shows that the maximum bending moment
67
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
happens at the right end of the pushing arm, i.e., at x=L. For a small actuation force,
combine this expression with Equation (3-25), then the maximum bending moment on
the pushing arm becomes
θθθ LEItFkM x
4−≈−= (3-27)
The maximum stress experienced by the pushing arm satisfies
( )
θθ
σ θ
LEh
IhtFk
IMh x 2
22≈
−== (3-28)
where h is the thickness of the pushing arm. We can see that the maximum tensile stress
experienced by the pushing arm is only determined by the ratio of thickness and length of
the pushing arm, i.e., h/L, in addition to the angle of rotation.
For the rectangular torsional beams, the maximum shear stress happens at the
midpoint of each longer side of the rectangular section with a value of
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛++=
432
2max 9100.08023.18865.06095.0116
3ab
ab
ab
ab
abTτ (3-29)
where T is the applied torque on the rectangular torsional beams.
As noncircular beams are twisted, their cross sections do not remain plane but warp.
When one or both ends of the torsional beam are fixed as in case of the micromirror,
warping is prevented and the stresses and the angle of rotation produced by a given
torque are affected. Here for the purpose of finding the maximum principle stress, we
ignore this effect to get an easier solution, i.e., the tensile stress associated with warping
is neglected. Therefore, the principle stresses related to a pure rotation in the torsional
beams are
(3-30) 02 =σmax31 τσσ =−=
68
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Single crystal silicon is a brittle material with a similar value of ultimate tensile
strength and ultimate compressive strength [59]. Therefore the best criterion to predict its
static-loading fracture condition is the maximum principal stress hypothesis, i.e. failure
occurs whenever one of the three principal stresses equals to or exceeds the yield tensile
strength. In order to determine the failure condition for static loading, the maximum
principal stress occurred on the pushing arm, described by Equation (3-28), and the
maximum principal stress occurred on the torsional beam, described by Equation (3-29),
is compared.
According to the maximum principal stress criterion, the safety factor for static
loading applied on a micromirror is
maxσuSn = (3-31)
where Su is the ultimate tensile stress, or yield stress of single crystal silicon, and σmax is
the maximum principal stress experienced by the pushing arm or the torsional beams.
69
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Symbol Parameters Value
Su yield stress of silicon (GPa) 3
E Young's modulus of silicon (GPa) 160
G shear modulus of silicon (GPa) 67
θ mechanically rotated angle (deg) 10.0
a half width of torsional beams (µm) 8
b half thickness of torsional beams (µm) 3
Lt length of torsional beams (µm) 150
kθ rotational spring constant of torsional beams (N⋅m) 7.9×10-7
σmax,t maximum principal stress in torsional beams (GPa) 0.46
w width of pushing arm (µm) 14
h thickness of pushing arm (µm) 6
L length of pushing arm (µm) 500
4EI/L rotational spring constant contributed by pushing arms (N⋅m) 3.2×10-7
σmax,p maximum principal stress in pushing arms (GPa) 0.67
n safety factor 4. 5
Table 3-2. Safety factor of a micromirror with nominal parameters for rectangular
cross-section torsional beams, pushing arms, and rotated angles.
Table 3-2 shows the calculated safety factor for an example of the micromirror design.
The failure for static loading happens on the pushing arm instead of on the torsional
beams. If setting the desired mechanical tilting angle, θ, to be ± 10° (optical scanning
angle: ± 20°) and taking a typical value of the pushing arm, h = 6 µm and L = 500 µm,
the maximum tensile stress experienced by the pushing arm is 0.67 GPa with a safety
factor of 4.48, while the maximum principal stress on the torsional beams is only 0.46
GPa, about two-thirds of the stress experienced by the pushing arm. The table also
70
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
indicates that the pushing arms contribute to a substantial part of the total rotational
spring constant, which is not desired as the process has no strict control over the
thickness of the pushing arms.
The most of uncertainty on the parameters that affect the safety factor in Table 3-2
falls on the thickness of the pushing arms. In the current process, they are fabricated
through a timed DRIE etch. The non-uniformity of etching speed across the wafer usually
brings a variance of 2~4 µm to the thickness of the pushing arms. As a result, the safety
factor might vary from 4.5 to 2.7, which still falls in the range of common safety factor
design.
In the case of a pulling lateral force, define the parameters in the opposite direction
and the same analytical results as Equations (3-23) - (3-25) are reached.
3.4.2. ANSYS simulation
The analytical results obtained from the mechanical modeling are compared with
numerical values obtained through ANSYS simulation. The ANSYS script simulating the
rotation of a micromirror under a static loading is attached in Appendix D. Main
structures, including micromirror, rigid linkages, pushing arms, and two torsional beams,
are included in the program. The appropriate boundary conditions are imposed on the
ends of torsional beams and pushing arms. The structures are meshed using solid92
elements and calculations are performed using the large-displacement nonlinear option.
Three points derived from ANSYS simulation are plotted in Figure 3-16, along with
the analytical result calculated from the previously-described beam model and its linear
approximation at small forces. We can see from Figure 3-16 that theoretical calculation
agrees with ANSYS simulation results especially in the small-force region. As the
71
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
actuation force, Fx, becomes larger, the displacement of the pushing arm, y, is larger and
the bending moment produced by the axial force on the pushing arm, -Fxy, is increased by
the second order of Fx. Thus nonlinearity appears and the angle of rotation is bigger than
the linear relationship predicted by the small actuation force region. However, ANSYS
result does not show a similar trend. One possible reason is that the nonlinear analysis in
ANSYS takes into account of beam stiffening at large displacement and this effect
cancels the nonlinearity brought by the bending moment of the pushing arm. In practical,
as the working range of the micromirror typically rests within ± 20° optically, assuming a
linear relationship between the angle of rotation and the actuation force is usually valid.
0
10
20
30
40
50
60
70
0.000 0.001 0.002 0.003 0.004 0.005 0.006Driving Force (N)
Act
uate
d O
ptic
al A
ngle
(deg
ree)
Beam Theory ResultLinearization of Beam TheoryANSYS Result
Figure 3-16. Relationship between the driving lateral force and the actuated rotation
angle of a micromirror, calculated by theoretical analysis and ANSYS
simulation.
72
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
In the case of non-ideal rotational beams, such as the one with thin, wide rectangular
cross sections, the boundary conditions assumed in the model, i.e., Equations (3-19) - (3-
22), are not true. For example, the 2 µm-thick torsional beams, which are used in the
initial design of the micromirrors, are not only susceptible to rotation motion, but also the
up-down lateral motion (using the axes defined in Figure 3-14). Therefore, the right side
of the pushing arm moves up and down along with the torsional beams as a
pushing/pulling lateral force is applied to its left end, instead of keeping at a fixed
position as assumed in the analytical model. Consequently, the results described in
Equations (3-23) - (3-25) are not valid for this case. In order to get a more accurate
analytical result, the lateral translation of the torsional beams must be taken into account
and this leads to a too complicated problem to be solved analytically. However ANSYS
FEM simulation is still able to provide a numerical prediction to the actuation of a
micromirror with thin, wide rectangular torsional beams. We observed that the
experimental DC actuation of one-axis scanning micromirror agrees with the ANSYS
simulation result within 15%.
3.5. Performance of Scanning Micromirrors
A fabricated two-axis scanning micromirror is shown in Figure 3-17. The
micromirror is 800 µm in length and 2 µm in thickness, with 50 µm-height ribs below to
stiffen the mirror. It is suspended by two 2 µm-thick, 50 µm-wide, and 200 µm-long
inner torsional beams and rests over a rigid surrounding frame made up by the two
bonded layers. The whole frame is then supported by two outer torsional beams that have
similar dimensions as the inner torsional beams.
73
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
2 µm-thick mirror
6 µm-thick arm
Lateral comb drive actuator
2 µm-thick layer
50 µm-thick layer
6 µm-thick decoupling beam
2 µm-thick mirror
Frame
2 µm-thick mirror
6 µm-thick arm
2 µm-thick mirror
6 µm-thick arm
Lateral comb drive actuator
2 µm-thick layer
50 µm-thick layer
6 µm-thick decoupling beam
2 µm-thick layer
50 µm-thick layer
6 µm-thick decoupling beam
2 µm-thick mirror
Frame
Figure 3-17. A two-axis scanning micromirror fabricated by the SOI/SOI wafer
bonding process. The central mirror is suspended by two inner
rectangular torsional beams and therefore rests over a rigid surrounding
frame which is supported by two outer rectangular torsional beams.
74
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
For both axes, there are two pushing arms connecting the torsional beams and the
lateral actuator. The inner pushing arms are 6 µm in thickness, 15 µm in width, and 400
µm in length while the outer pushing arms are 6 µm in thickness, 11 µm in width, and
830 µm in length. The 6 µm-thick, 10 µm-wide, and 310 µm-long decoupling beam
connecting the inner pushing arms and the inner comb drive actuator shields the actuator
from rotating around the outer axis. It can be seen that the edges of 6 µm-thick beams
have small silicon spikes. They are frequently seen on the structures formed by the timed
DRIE etching due to the micromasking [60]. However, these grass-like defects should not
affect the mechanical function of the structures since they are small in size and quantities.
Figure 3-17 shows only part of the two lateral comb drive actuators with tapered fingers
and two of the four crab leg flexures suspending the actuator. The tapered comb fingers
are designed to achieve a certain DC scanning angle at a lower actuation voltage than the
one of using parallel comb fingers. As the comb fingers move in, the effective gap
distance between the two groups of tapered comb fingers decreases in contrast to the
constant gap distance when using parallel comb fingers. Therefore the electrostatic
actuation force increases as it inversely depends on the gap distance.
3.5.1. DC and AC actuation of fabricated one-axis scanning micromirrors
The static (DC) response of scanning micromirrors is captured by detecting the shifts
of the laser beam reflected by actuated micromirrors. Figure 3-18 shows the angle
displacement of a one-axis pulling-mode scanning micromirror under DC actuation. A
scanning angle of 21.8° is achieved at 75.0 V with the comb drive actuator pulling in
afterwards as a result of the combined effect of the side instability and rotation instability.
In order to attain a larger DC actuation range, a more stable design of the suspension
75
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
beams for the comb drive actuator is required, both in terms of the side stiffness and
rotating stiffness. The deviation from a linear relationship between the displaced angle
and the actuation voltage is mainly due to the tapered comb fingers in the comb drive
actuator. As the comb fingers are pulled closer, the gap distance between them decreases
and the electrostatic force increases, inducing a larger rotation angle on the micromirror.
0
5
10
15
20
25
0 1000 2000 3000 4000 5000 6000Actuation Voltage ^2 (V^2)
Opt
ical
Sca
nnin
g A
ngle
(deg
ree
Opt
ical
Sca
nnin
g A
ngle
(deg
ree)
0
5
10
15
20
25
0 1000 2000 3000 4000 5000 6000Actuation Voltage ^2 (V^2)
Opt
ical
Sca
nnin
g A
ngle
(deg
ree
Opt
ical
Sca
nnin
g A
ngle
(deg
ree)
Figure 3-18. DC actuation of a one-axis pulling scanning micromirror.
Compared to the previous results reported in [61], the maximum DC scanning angle
of the one-axis scanning micromirror is increased from 11.0° to 21.8°. This enhanced
performance is benefited from changing the electrical connection of the substrate on the
device from floating to grounding. Leaving the substrate floating brings an uncertainty to
the charge leakage and induces instability to the charge distribution on the comb drive
actuator. This induces the micromirror vibrating when the actuation voltage is high.
76
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Grounding the substrate eliminates the instability of the charge distribution and the
micromirror is able to work under a larger actuation voltage.
The experimental data agrees with the ANSYS analysis result. The lateral comb drive
actuator is calculated to generate a pulling force of 0.97 mN at 75.0 V. The force is
applied to a one-axis micromirror with similar dimensions in ANSYS and the simulation
shows that the micromirror scans the laser beam up to 18.4° optically. Compared to 21.8°
in experiments, the simulation result agrees with the experimental observation to be
within 15%. The difference between them comes from the estimation over the thickness
of the pushing arm, which is somewhat difficult to measure after the substrate is etched
away.
A modal analysis of the one-axis pulling mirror is carried out and calculates the first
four modes of the micromirror, whose mode shapes and frequencies are shown in Figure
3-19. Since the simulation only takes the mirror plate, the torsional beams, and the
pulling arms into account and leaves the comb drive actuator and its suspension beams
out, only the mode shapes accurately describe the situation while their frequencies are off,
especially for the modes which involve large displacements of the comb drive actuator.
The first mode, sitting on the left, top corner of the picture, corresponds to the out-of-
plane lateral movement of the micromirror; The second one, sitting on the right, top
corner of the picture, describes the rotation of the micromirror; the left, bottom one
displays the left-right twisting motion of the micromirror; and the right, bottom one
shows the dynamic deformation mode of the mirror plate. Since the out-of-plane lateral
and torsion modes of the micromirror involve large displacements of the comb drive
actuator in Y direction, their frequencies are not able to be obtained accurately through
77
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
simulations without including the actuator part while the frequencies of the twisting and
dynamic deformation modes can be accurately predicted by the simulations, given an
accurate input of the device dimensions.
Displacement in ZMode 2. 6.04 kHz
Displacement in ZMode 4. 42.21 kHz
Displacement in ZMode 3. 8.41 kHz
Displacement in ZMode 1. 2.67 kHz
Displacement in ZMode 2. 6.04 kHz
Displacement in ZMode 4. 42.21 kHz
Displacement in ZMode 3. 8.41 kHz
Displacement in ZMode 1. 2.67 kHz
Figure 3-19. The four lowest resonant mode of a one-axis pulling micromirror.
Mode 1: out-of-plane lateral mode; Mode 2: rotation mode; Mode 3:
left-right twisting mode; Mode 4: mirror plate deformation mode.
The AC response of the one-axis micromirror is characterized using a laser Doppler
vibrometor (LDV) as the micromirror is actuated by an AC voltage source with a large
DC bias. Two groups of data were taken when the laser beam from the LDV was
positioned individually on the two opposite edges of the mirror, each about 400 µm from
the axis of rotation. The location of the detected points is chosen in this way so that the
78
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
signal corresponding to the rotation mode of the micromirror is strongest. The amplitude
and phase of the mirror movement in the out-of-plane direction are displayed in Figure 3-
20. Figure 3-20 (a) is measured on the spot where the rotation and the lateral out-of-plane
mode is co-phase under low frequency actuation while (b) is taken on the opposite side of
the mirror, where the rotation and the lateral out-of-plane mode is out-of-phase. The
phase difference between two groups of data is 180° at most frequencies since the
rotation mode dominates the movement of the mirror, except at the resonant frequencies
of the out-of-plane lateral mode and left-right twisting mode. According to their phase
differences, we were able to distinguish the rotational mode from the other modes. The
result shows that the one-axis device has a rotational resonant frequency of 3.6 kHz with
a quality factor of 12. The second mode at 4.1 kHz corresponds to the lateral out-of-plane
motion of torsional beams while the additional mode at 6.8 kHz is related to the left-right
twisting mode of the micromirror. Compared to the FEM simulation results of 2.67 kHz
(lateral out-of-plane mode), 6.04 kHz (rotational mode), and 8.41 kHz (left-right twisting
mode), the differences arise from the fact that the model does not take into account of the
comb drive array and its suspension beams. Furthermore, the analysis inputs several
estimated dimensions, such as the thickness of the transfer arms.
79
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
-500
-400
-300
-200
-100
0
1000 10000Frequency (Hz)
Phas
e (d
egre
e)
0
0
1
10
1000 10000Frequency (Hz)
Vel
ocity
^2
(a.u
.)
-300
-200
-100
0
100
200
1000 10000Frequency (Hz)
Phas
e (d
egre
e)
0
0
1
1000 10000Frequency (Hz)
Vel
ocity
(a.u
.)
Phas
e of
Vel
ocity
(d
egre
e)
103 104
Am
plitu
de o
f V
eloc
ity (a
.u.)
101
100
10-1
10-2
103 104
3.6 kHz4.1 kHz
6.8 kHz
103 104
Phas
e of
Vel
ocity
(d
egre
e)A
mpl
itude
of
Vel
ocity
(a.u
.)
100
10-1
10-2
103 104
3.6 kHz 6.6 kHz(a) (b)
-500
-400
-300
-200
-100
0
1000 10000Frequency (Hz)
Phas
e (d
egre
e)
0
0
1
10
1000 10000Frequency (Hz)
Vel
ocity
^2
(a.u
.)
-300
-200
-100
0
100
200
1000 10000Frequency (Hz)
Phas
e (d
egre
e)
0
0
1
1000 10000Frequency (Hz)
Vel
ocity
(a.u
.)
Phas
e of
Vel
ocity
(d
egre
e)
103 104
Am
plitu
de o
f V
eloc
ity (a
.u.)
101
100
10-1
10-2
103 104
3.6 kHz4.1 kHz
6.8 kHz
103 104
Phas
e of
Vel
ocity
(d
egre
e)A
mpl
itude
of
Vel
ocity
(a.u
.)
100
10-1
10-2
103 104
3.6 kHz 6.6 kHz(a) (b)
Figure 3-20. Frequency response of a one-axis pulling scanning micromirror. (a):
measured on the spot where the rotation and the lateral out-of-plane
mode is co-phase when actuated at low frequencies; (b) measured on
the opposite side of the mirror, where the rotation and the lateral out-of-
plane mode is out-of-phase.
3.5.2. DC and AC actuation of fabricated two-axis scanning micromirrors
Figure 3-21 shows the laser beam reflected by a two-axis scanning micromirror under
DC and AC actuation. For DC actuation, the comb drive actuator pulls in afterwards as
happened in the case of one-axis scanning micromirror, resulting from the combined
effect of the side instability and the rotation instability. There is slight cross-axis coupling
between the inner and outer rotation of the two-axis micromirror. When driving the inner-
axis actuator, the mirror rotates not only around the inner axis, but also the outer axis.
80
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
This problem is addressed later in the thesis. For AC actuation, the micromirror is able to
scan Lissajous curves as shown in the right picture of Figure 3-21.
reflected from the
frame
reflected from the nearby chip
reflected from the scanning
mirror Scattered by the nearby probe
reflected from the
frame
reflected from the nearby chip
reflected from the scanning
mirror Scattered by the nearby probe
Figure 3-21. Reflected laser beam by a two-axis scanning micromirror under DC
and AC actuation (each minor grid element represents 1° of optical
deflection.) Left: Vvert. = 60.2 V, Vhorz. = 79.9 V; Right: Vvert. = 45.1 +
10 × sin(2π×300×t), Vhorz. = 45.4 + 10 × sin(2π×100×t).
The two-axis micromirror scans up to 15.9° optically for the inner axis and 13.2° for
the outer axis under a static actuation, as shown in Figure 3-22. A further increase of its
dc scanning range needs to design the suspension beams of the comb drive actuators with
higher stability to work under large displacements. This is addressed in the later part of
the thesis.
81
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
0
2
4
6
8
10
12
14
16
18
0 1000 2000 3000 4000 5000 6000Actuation Voltage ^2 (V^2)
Opt
ical
Sca
nnin
g A
ngle
(deg
ree Scanning over the inner axis
Scanning over the outer axis
Opt
ical
Sca
nnin
g A
ngle
(deg
ree)
0
2
4
6
8
10
12
14
16
18
0 1000 2000 3000 4000 5000 6000Actuation Voltage ^2 (V^2)
Opt
ical
Sca
nnin
g A
ngle
(deg
ree Scanning over the inner axis
Scanning over the outer axis
Opt
ical
Sca
nnin
g A
ngle
(deg
ree)
Figure 3-22. DC actuation of a two-axis scanning micromirror.
The resonant frequency of the rotation mode over the inner axis for this two-axis
micromirror is 2.2 kHz while the one over the outer axis is 1.3 kHz. Compared to the
analytical results of 2.5 kHz for the inner axis and 1.2 kHz for the outer axis, they agree
within 15%.
3.6. Reliability and Robustness of Micromirrors
3.6.1. Reliability of micromirrors
The micromirror fabricated by the SOI/SOI wafer bonding process is expected to be
exceedingly reliable because of its monolithic single crystal silicon design. Single crystal
silicon is intrinsically resistant to fatigue and the all-suspension design eliminates the
frictional wear associated with contacting surfaces. Moreover, the bonding formed by
82
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
surface chemical activated pre-bonding and high temperature annealing have a strong
strength to hold two layers together.
However, a defective bonding interface may set off the propagation of a fatigue crack
and thus the device may fail because of delamination or fracture. Also the initiation of a
fatigue crack frequently occurs at the point of highest strain in the device. Therefore the
transfer arm, formed by a timed DRIE etch, may break at its linkage to the mirror plate
since that point experiences the maximum stress in a whole device.
A test was carried out to assess the long-term reliability of micromirrors. A one-axis
scanning micromirror was actuated for 34 days at 6.4 kHz, a frequency around its
rotational resonant frequency, with scanning amplitude of 17.8° optically. By measuring
the resonant frequency and scanning amplitude under a constant AC and DC driving
voltage, we were able to detect small changes in the mirror that could be indicative of
material fatigue. For example, a monotonic decrease in the resonant frequency or a
monotonic increase in the scanning amplitude might indicate fatigue and crack growth in
the device.
The scanning micromirror turns out to be quite durable. The resonant frequency and
amplitude were measured periodically and are displayed in Figure 3-23 and Figure 3-24.
We found that the change over its resonant frequency for 18.9 billion cycles is less than
1.2 % and the change over the amplitude is within 2.2 %. The device is still functional
after operated for 18.9 billion cycles. The small and irregular change over the resonant
frequency and amplitude indicates that no obvious fatigue is developed through the long-
term operation of the micromirror.
83
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
6.18
6.20
6.22
6.24
6.26
6.28
0.0 5.0 10.0 15.0 20.0Cycles (Billion)
Freq
uenc
y (k
Hz)
Figure 3-23. Measured resonant frequency of a one-axis scanning micromirror,
running at 6.4 kHz with scanning amplitude of around 17.8° for 18.9
billion cycles. The variation of resonant frequency is less than 1.2 %.
17.6
17.7
17.8
17.9
18.0
18.1
0.0 5.0 10.0 15.0 20.0Cycles (Billion)
Scan
ning
Ang
le (d
egre
e)
Figure 3-24. Measured scanning angles of a one-axis scanning micromirror, running
at 6.4 kHz with scanning amplitude of around 17.8° for 18.9 billion
cycles. The variation of scanning amplitude is less than 2.2 %.
84
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
3.6.2. Shock resistance of micromirrors
The multi suspension beams with high stiffness enable the lateral-actuated
micromirror to be quite resistant to shock and vibration. The acceleration of the mirror is
resisted both by the torsional beams and actuator suspension beams in contrast to the
single torsional beams as in the case of micromirrors with vertical/angular comb drive
actuators. The high-stiffness spring design of the lateral-actuated micromirror also helps
preventing the fracture or stiction of the structures under large shock loads.
Two major failure modes associated with the shock loads are dynamic fracture and
quasistatic fracture. Assume the device has a lowest resonant frequency fres. When the
pulse duration τ is smaller than 2.5/fres, the device is excited resonantly and its
acceleration of the mass can exceed the applied maximum acceleration. When the pulse
duration τ is bigger than 2.5/fres, the device behaves quasistatically and its acceleration of
the mass is equal to the applied maximum acceleration [62]. The reported values of the
pulse duration for the applied shock loads are in the range 50 µs – 6 ms [62]. We pick 1
ms, a typical number for many shock tests. The fabricated two-axis micromirror has a
lowest resonant frequency of 1.3 kHz and the pulse duration τ of 1 ms is smaller than
2.5/fres (1.9 ms). Therefore the mirror plate of the two-axis device is expected to be
excited resonantly during the shock test. However, for most one-axis micromirrors, the
lowest resonant frequency is around 3.5 kHz and the pulse duration τ of 1 ms is bigger
than 2.5/fres (0.71 ms). So the one-axis mirror is expected to be excited quasistatically
during the shock test.
For the quasistatic case, the maximum lateral force, F, induced by the loading shock
is m·amax, where m is the mass of the comb drive actuator, about 5×10-8 kg, and amax is the
85
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
peak acceleration during a shock test, which is chosen to be 500 g in our shock test.
Therefore the lateral force applied to the micromirror is about 0.25 mN. According to
Table 3-2, the maximum static lateral force a typical micromirror can survive is about 6.9
mN. Therefore the device should be able to survive through this kind of shock without
any problem when excited quasistatically.
For the resonant case, assume that the device has a quality factor of 20 for its lowest
resonant mode, the maximum lateral force generated by the loading acceleration is about
20·0.25 mN, or 5 mN. It is less than the quasistatic toughness, 6.9 mN. Moreover, the
dynamic fracture toughness of brittle materials is usually greater than, or equal to, the
corresponding quasistatic fracture toughness [63]. Therefore the two-axis micromirror
should be able to survive through the shock test.
A non-operational shock test was carried out to assess the robustness of the
micromirror. A 1cm × 1cm chip, which has one functional two-axis micromirror and two
functional one-axis micromirrors, is glued onto a ceramic package using a very thin layer
of silver epoxy. The package is then securely clamped on the table of a linear shake
machine from GHI systems, as shown in Figure 3-25. We assume that this attachment
mechanism does not significantly alter the shape or intensity of the shock pulse
experienced by the devices.
86
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
Packaged chipPackaged chip
Figure 3-25. The packaged chip is securely clamped on a shake table, ready for the
shock test.
The micromirror chip was subjected to four shocks each along the directions of the x,
y, and z-axis. Each shock, whose pulse shape was recorded by an accelerometer on the
shake table, has a peak acceleration of 500 g and pulse duration of 1 ms, as displayed in
Figure 3-26. The devices were examined with an optical microscope as well as
electrically actuated after the shock test. All three devices, including a two-axis
micromirror, a pulling one-axis micromirror and a push one-axis micromirror, are still
functional after the shock test. The observed reliability of the devices was found to be in
agreement with the predictions of the analyses.
87
MEMS SCANNING MICROMIRRORS AND SOI/SOI WAFER BONDING PROCESS
-200
-100
0
100
200
300
400
500
600
0 1 2 3 4Time (msec)
Acc
eler
atio
n (g
)
Figure 3-26. Representative example of an acceleration pulse during the shock test.
Duration: 1 ms; Peak acceleration: 500 g.
88
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
4. MEMS SCANNING MICROMIRRORS WITH T-BAR
TORSIONAL BEAMS
4.1. Torsional Beams with T-Shaped Cross Section
The previous gimbaled two-axis micromirror exhibits a cross-coupling between the
two axial rotations. When a voltage is applied over the outer-axis comb drive actuator,
the resulting rotation is purely around the outer axis. However, when driving the inner-
axis actuator, the mirror rotates not only around the inner axis, but also the outer axis. As
the voltage is increased and the mirror rotates more around the inner axis, the rotation
over outer axis increases, too.
The reason for the cross-coupling lies in the thin torsional beams of the outer gimbal
with rectangular cross sections. When a lateral force is pushing against the inner-axis
torsional beams, the inner transfer arm bends and generates an upward force on the frame
and therefore on the outer-axis torsional beams. Consequently, those two outer-axis
beams bend upwards since the 2 µm-thick torsional beams are not only susceptible to
rotational motion, but also compliant to out-of-plane lateral motion. The two transfer
arms attached to the outer-axis torsional beams follow the bending and produce a
rotational torque onto the outer torsional beams. As a result, the mirror rotates around the
outer axis.
The solution for the cross-axis coupling in the two-axis micromirror is using torsional
beams that are compliant to rotational movement but robust to both in- and out-of-plane
89
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
lateral movements. Torsional springs using open, thin-walled cross sections, such as T-
shaped cross sections, provide such an optimal combination of spring stiffnesses [64].
y
x
tf
b
h
tw
tfy
x
y
x
tf
b
h
tw
tf
Figure 4-1. T-shaped cross section torsional beams.
The bending stiffness kx and ky of T-bar torsional beams are calculated to be
(4−1) 33333 /2/)(2 ltEblhttbEk wwx f≈+≈
(4−2) 33333 /2/)(2 lhEtlhtbtEk ffwy ≈+≈
where E is the Young’s modulus of the material, b and tw is the width and thickness of the
web, tf and h is the width and thickness of the flange (see Figure 4-1), and l is the length
of torsional beams. The torsional stiffness kθ is described to be
lhtbtGk fw /)(32 33 +=θ (4−3)
where G is the shear modulus.
Compared with a rectangular-shaped torsional beam, spring constants of T-bar
torsional beams are strengthened in both lateral directions by several hundred times
(depending on the dimensions of the structure) whereas the torsional stiffness is only
90
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
doubled. Thus, micromirrors with T-bar torsional beams not only keep high transmission
efficiency, but also have less cross-coupling between the two axial rotations.
The use of T-bar torsional beams is compatible with our current process. The web
structure of the T-bar is fabricated on the 2 µm bonding layer while the flange part is
made of the underlying 50 µm layer. A schematic of the micromirror suspended by two
T-bar torsional beams is shown in Figure 4-2.
Lateral force
Low-mass mirror
Transfer arm
T-shaped cross-section torsional beams
Lateral force
Low-mass mirror
Transfer arm
T-shaped cross-section torsional beams
Figure 4-2. A mirror is suspended by two T-bar torsional beams.
4.2. ANSYS FEM Simulation
FEM simulation confirms this analysis, as shown in Figure 4-3. Figure 4-3 (a) shows
that for a scanner with rectangular torsional beams, the torsional beams of the outer axis
bend upwards and the mirror tilts around both the inner and outer axis as a pushing force,
Fx, is exerted on the inner-axis transfer arm. On the contrary, in Figure 4-3 (b), the two-
axis scanner with T-bar torsional beams shows no tilt over its outer axis and thus no
cross-coupling effect between its inner and outer axes.
91
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
(a)
Rectangular Cross Section
FxOuter-axis torsional beams bend upwards, and mirror tilts around both inner and outer axis.
Rectangular Cross Section
FxOuter-axis torsional beams bend upwards, and mirror tilts around both inner and outer axis.
(b)
T-shaped Cross Section
FxOuter-axis torsional beams do not bend, and mirror rotates around inner axis only.
T-shaped Cross Section
FxOuter-axis torsional beams do not bend, and mirror rotates around inner axis only.
Figure 4-3. (a) ANSYS simulation shows cross-coupling for two-axis scanner with
rectangular shaped cross section torsional beams; (b) ANSYS
simulation shows no cross-coupling for two-axis scanner with T-shaped
cross section torsional beams.
92
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
4.3. DC and AC Actuation of Micromirrors with T-bar Torsional Beams
A fabricated two-axis scanning mirror with T-shaped cross-section torsional beams is
shown in Figure 4-4. The image is taken from an optical microscope with a spatial high-
pass filter to show the edges clearly. As visible light is partially transmitted through a 2-
µm silicon layer, we can see the underlying 50-µm structures. The mirror is 800 µm in
diameter and 2 µm in thickness, with 50 µm-height ribs below to stiffen the mirror. The
T-bar torsional beams consist of two parts, the 80 µm-wide web structure in the 2 µm-
thick bonding layer and the 3 µm-wide flange part in the 50 µm-thick layer.
Comb drive actuator
Com
b dr
ive
actu
ator
Transfer arm
T cross-section torsional beams
2 µm-thick mirror with underlying 50 µm ribs
T cross-section torsional beams
Comb drive actuator
Com
b dr
ive
actu
ator
Transfer arm
T cross-section torsional beams
2 µm-thick mirror with underlying 50 µm ribs
T cross-section torsional beams
Figure 4-4. A gimbaled two-axis scanner by the SOI/SOI bonding process.
As stated in Figure 4-5, the bi-directional two-axis micromirror works up to ±7° for
the outer-axis and from -3° to 7° for the inner-axis under DC actuation. The scanner pulls
in afterwards due to the same lateral and rotational instabilities in the comb drive array.
93
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
The limited scanning range over the inner axis is due to a small defect on its pulling
comb drive array. As predicted, there is no observed cross-coupling between two axial
rotations when a two-axis micromirror rotates around its inner axis up to 15°, actuated
manually with a probe.
-8
-6
-4
-2
0
2
4
6
8
0 1000 2000 3000 4000
Actuation Voltage ^2 (V2)
Opt
ical
Ang
le (d
egre
e)
Inner PushInner PullOuter PushOuter Pull
Figure 4-5. DC actuation of a bi-directional two-axis scanner with T-shaped cross-
section torsional beams.
Figure 4-6 shows the simulated modal shape and frequencies for the lowest four
modes in a one-axis micromirror using Pro-mechanica. As we can see, the resonant
frequency of the second mode is 40 kHz higher than that of the first mode.
94
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
Displacement in ZMode 2. 47.6 kHz
Displacement in ZMode 4. 95.4 kHz
Displacement in ZMode 3. 61.4 kHz
Displacement in ZMode 1. 7.73 kHz
Displacement in ZMode 2. 47.6 kHz
Displacement in ZMode 4. 95.4 kHz
Displacement in ZMode 3. 61.4 kHz
Displacement in ZMode 1. 7.73 kHz
Figure 4-6. Modal shapes and frequencies of a one-axis scanner with T-shaped
cross-section torsional beams. Mode 1: torsion mode; Mode 2: transfer
arm bending mode; Mode 3: out-of-plane lateral mode; Mode 4: in-
plane lateral mode.
The measured frequency response of a one-axis mirror with T-bar torsional beams
using a laser Doppler vibrometer is shown in Figure 4-7. It has a torsional resonance
frequency at 6.4 kHz, higher than that of a one-axis mirror with rectangular torsional
beams (3.6 kHz). The second mode at 25.3 kHz is far away from the first mode, as the
analytical simulation predicts.
95
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
(a)
0.001
0.010
0.100
1000 10000 100000Frequency (Hz)
Am
plitu
de o
f Vel
ocity
(a.u
.)
6.4 kHz
25.3 kHz
10-1
10-2
10-3
103 104 105
0.001
0.010
0.100
1000 10000 100000Frequency (Hz)
Am
plitu
de o
f Vel
ocity
(a.u
.)
6.4 kHz
25.3 kHz
10-1
10-2
10-3
103 104 105
(b)
-600.0
-400.0
-200.0
0.0
1.0E+03 1.0E+04 1.0E+05Frequency (Hz)
Phas
e (d
egre
e)
103 104 105
Phas
e of
Vel
ocity
(deg
ree)
-600.0
-400.0
-200.0
0.0
1.0E+03 1.0E+04 1.0E+05Frequency (Hz)
Phas
e (d
egre
e)
103 104 105
Phas
e of
Vel
ocity
(deg
ree)
Figure 4-7. Measured frequency responses of a one-axis scanner with rectangular
cross-section torsional beams and one with T-shaped cross-section
torsional beams.
96
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
4.4. Comb Drive Actuators for Large Displacements
Most micromirrors fail with the comb drive actuator pulled_in due to its lateral and
rotational instabilities under large static displacements. An ideal suspension is compliant
in the direction of desired displacement and stiff in the orthogonal directions and
rotations. A crab-leg flexure is used as the suspension beam of the comb drive actuator,
as shown in Figure 4-8, due to its large linear deflection region.
y
x
g
∆g
g
∆g
Fy +_
(L2, I2) (L1, I1)
y
x
g
∆g
g
∆g
Fy +_
(L2, I2) (L1, I1)
Figure 4-8. A comb drive actuator suspended by a crag leg flexure.
The forward and side stiffness of the crab suspension beam, kx and ky, at zero
deflection are given by:
⎥⎦⎤
⎢⎣⎡
++
=υυ
4148
32
2
LEIkx (4−4)
⎥⎦⎤
⎢⎣⎡
++
=υ
υ41
14831
1
LEIky (4−5)
with 12
21
LILI
=υ , while E is the Young’s modulus of silicon, I1 and I2 are the momentum of
the inertia for the shin and thigh of the crab leg flexure, L1 and L2 are the length of the
shin and thigh. The side-to-forward stiffness ratio (ky/kx) at zero displacement is high
(around 10000 for a crab leg flexure with L1 = 50 µm, W1 = 11.4 µm, L2 = 650 µm, W2 =
97
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
4.5 µm, t = 50 µm.) However, the side stiffness, ky, decreases with increasing lateral
deflections and the comb drive actuator becomes more vulnerable to side pull_in.
A suspension flexure is also susceptible to rotation z axis, the out-of-plane direction.
As shown in Figure 4-9, the torque that restores the rotation of the comb drive actuator
comes from the lateral spring force. Therefore, the rotation stiffness kθ of the crab
suspension beam is related with the lateral stiffness, kx and ky, by the following equation:
xykyxkk yx ⋅∆⋅+⋅∆⋅=∆⋅ θθ (4−6)
where ∆θ, ∆x, and ∆y are the angle and lateral displacement of the joint from its original
position.
Comb Drive
ky
kx
(x,y)
(0,0)
Comb DriveComb Drive
ky
kx
(x,y)
(0,0)
Comb Drive
Figure 4-9. The rotation restoring force on a comb drive actuator is provided by the
lateral spring forces.
∆x and ∆y are related with ∆θ by the following equations:
θθ∆⋅−
∆−≈−=∆ yxxxx
2'
2
(4−7)
θθ∆⋅+
∆−≈−=∆ xyyyy
2'
2
(4−8)
98
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
Then we have a simpler expression of kθ:
(4−9) θθθθ ∆⋅⋅+∆⋅⋅=∆⋅ 22 xkykk yx
(4−10) 22 xkykk yx ⋅+⋅=⇒ θ
Assume that kx << ky since the design of the crab leg flexure makes a high stiffness
ratio between kx and ky. kθ is related with ky only:
(4−11) 2xkk y ⋅≈θ
Therefore the problem of designing a crab leg flexure with high rotation stiffness is
combined to the problem of designing one with high side stiffness. In addition, placing
the suspension on the upper and bottom position of the combs, i.e. maximizing x
according to Equation 4-11, also helps increasing rotational stiffness.
At large deflections, the side stiffness contributed from the thigh of the crab leg
flexure, ky, decreases to [65]
22
2
3100
xLEIky ∆
= (4−12)
From this expression, we can see that the side stiffness decreases with increasing
deflection in the x direction.
In order to increase the range of DC deflections, several strategies can be applied.
(1) Increase the forward stiffness of the suspension beams by increasing the width of
the flexure or decreasing the length of the flexure. Increasing the width of the flexure is
more effective since the side stiffness at large deflections is proportional to the cube of
the width according to Equation 4-12. Compared to the stiffness of the pushing arm and
torsional beams, the stiffness of the suspension beams contribute less than 1% to the total
99
MEMS SCANNING MICROMIRRORS WITH T-BAR TORSIONAL BEAMS
stiffness. Therefore increasing the forward stiffness of the suspension beams will not
significantly affect the performance of micromirrors.
(2) Maximize the gap spacing of the comb drive actuator if a higher actuation voltage
is allowed since the comb drive actuator with small gap spacings are more susceptible to
side instabilities. The electrostatic force in the side direction is proportional to the cube of
the gap while the actuation force in the forwarding direction is only linearly proportional
to the gap. As the gap size increases by a factor of α, the voltage required to reach a
certain displacement increases by a factor of α , while the side stability is increased by
a factor of α.
(3) Employ pre-bent suspension beams [66] for the devices that work unidirectionally.
With pre-bent suspension beams, the side stiffness will be low initially and increase as
the suspension beams straighten. Therefore the side stiffness is low when the side
electrostatic force is low and increases as the side electrostatic force increases. It is
estimated that the use of pre-bent suspension beams increase the range of the deflection
by a factor of two [66].
100
MEMS SCANNING MICROMIRROR
5. CONCLUSIONS AND DISCUSSIONS
The focus of this dissertation is the development of two optical MEMS devices,
CCRs and scanning micromirrors, for free-space communication.
5.1. Summary of Results over CCRs
Sub-millimeter-sized CCRs are fabricated by assembling two side mirrors onto an
actuated bottom mirror. Assembled CCRs exhibit mirror non-flatness less than 50 nm,
mirror roughness less than 2 nm, and mirror angular misalignment less than 1 mrad
(0.06°), leading to near-ideal optical performance. The angular alignment accuracy is
achieved through locking the positions of the two side mirrors using spring flexures and
protrusion-notch structures. The quad CCR incorporates an electrostatic gap-closing
actuator, formed between the device layer and the substrate of the fabricated SOI wafer,
allowing their reflectivity to be modulated up to 7 kb/s. The actuation voltage is as small
as 4.7 V, compatible with the driving solar cell power and CMOS control switches. The
energy consumption, which averages 19 pJ per bit, is consistent with the power
requirements of a millimeter-scale autonomous sensor node. A 180-m free-space optical
communication link using a CCR as a passive optical transmitter has been demonstrated.
Quad CCRs have been integrated with other parts of Smart Dust mote, formulating
miniature, autonomous nodes that constitute a distributed wireless sensor network. An
analysis of the signal-to-noise ratio of CCR-based links, considering the impact of CCR
dimensions, ambient light noise, and other factors, has been presented.
101
MEMS SCANNING MICROMIRROR
5.2. Summary of Results over Scanning Micromirrors and SOI/SOI Wafer Bonding
Process
An SOI/SOI wafer bonding process is developed to fabricate scanning mirrors
actuated by lateral comb drive actuators. The process is an extension of SOI technology
and can be used to fabricate stacked high-aspect-ratio structures with well-controlled
thicknesses. Strategies, such as retaining an oxide layer on the back of the SOI wafer to
decrease the bow of the wafer and allocating more than 50% of the wafer surface as
bonding area to guarantee adequate bonding force, are employed to increase the yield of
the process. The bonding interface is characterized by SEM and infrared images,
indicating solid bonding between wafers. The I-V curves of bonded structures suggest
that electrical interconnection can be made through bonded layers, providing flexibility to
the interconnection design. A shear stress test is carried out and measures the lower limit
of the ultimate shear stress to be 1.01 MPa. The bonded structures show an excellent air
sealing property since the pressure inside the sealed cavities capped by a bonded layer
agrees with the read-out of the pressure gauge on the bond aligner during bonding.
An analytical simulation is established to analyze the scanning micromirrors by
employing the universal beam theory, considering the axial force acted on the transfer
arms, and assuming proper boundary conditions. It is best for predicting the rotation
angle and maximum stress of the scanning micromirrors having torsional beams with
high stiffness ratio between the lateral stiffness and the torsional stiffness such as T-bar
torsional beams, while not accurate for the case with thin, wide rectangular cross-section
since the latter case does not satisfy the assumed boundary conditions.
102
MEMS SCANNING MICROMIRROR
The fabricated one-axis micromirror with rectangular cross-section torsional beams
has the capability of scanning 21.8° under a DC actuation voltage of 75.0 V. It agrees
with the ANSYS FEM result within 15 %. The frequency response of the one-axis
micromirror shows that the mirror has a rotational mode at 3.6 kHz, an out-of-plane
lateral mode at 4.1 kHz, and a left-right twisting mode at 6.8 kHz. The fabricated two-
axis micromirror scans up to 15.9° optically under a DC actuation voltage of 71.8 V for
the inner axis and 13.2° at 71.2 V for the outer axis. The resonant frequency of the
rotation mode over the inner axis for this two-axis micromirror is 2.2 kHz while the one
over the outer axis is 1.3 kHz.
Torsional beams with T-shaped cross sections are introduced to replace rectangular
torsional beams in the two-axis MEMS micromirror in order to reduce the cross-coupling
between the two axial rotations. T-bar torsional beams have a high lateral stiffness in
both in- and out-of-plane directions while keeping a low torsional compliance. Also the
use of T-bar torsional beams is compatible with the SOI/SOI wafer bonding process that
is used to fabricate micromirrors. The two-axis micromirror with T-shaped cross-section
torsional beams shows no cross-coupling between two axial rotations within a large range
of scanning angles. The fabricated bi-directional two-axis micromirror works up to ±7°
for the outer-axis and from -3° to 7° for the inner-axis under DC actuation. The measured
frequency response of a one-axis mirror with T-bar torsional beams shows a torsional
resonance frequency at 6.4 kHz, higher than that of a one-axis mirror with rectangular
torsional beams.
The micromirror was observed to be quite durable with no obvious frequency and
scanning angle shifts after running at 6.4 kHz with scanning amplitude of around 17.8°
103
MEMS SCANNING MICROMIRROR
for 18.9 billion cycles. The micromirrors were tested on a shake table, subjected to
shocks with a peak acceleration of 500 g and pulse duration of 1 ms along the directions
of all three axes. All three devices were functional after the shock tests.
5.3. Future Work
Both CCRs and scanning micromirrors are developed to facilitate free-space optical
communication, establishing optical link among sensor nodes or between sensor nodes
and interrogating center. Future research directions should concentrate on the integration
and further development of the system.
Here is a list of possible research directions.
(1) Automated assembly of CCRs. Although the assembled CCRs display near-ideal
optical quality and excellent actuation performance, manual assembly of CCR mirrors is
a drawback of the current process. The automation of assembly can be realized by using
vacuum tips to handle small objects. The outer diameter of commercially available tips
can be as small as 200 µm, able to grab the side mirrors without blocking its pathway.
The ‘on’ and ‘off’ of the vacuum makes grabbing and releasing of the small objects
convenient. The placement of side mirrors can be controlled by programming micro-
positioners with six degrees of freedom.
(2) Optimization of scanning micromirror design. The comb drive actuator of
scanning micromirrors needs to be redesigned, as suggested in the previous chapter, so
that micromirrors have a larger DC scanning range. This can be done by increasing the
forward stiffness of the suspension beams, maximizing the gap spacing of the comb drive
actuator, or employing pre-bent suspension beams. The mirror surface needs to be metal
coated. Either gold or aluminum coating is able to bring up the reflection of a mirror
104
MEMS SCANNING MICROMIRROR
surface from 30 % to more than 90 %. However, coating the mirror with metal introduces
stresses to the 2 µm-thick surface, inducing curvature to the mirror. Putting 50 µm-thick
stiffening ribs behind the mirror surface helps keeping the mirror flat while the position
and shape of the stiffening ribs need to be optimized so that it contributes minimum
amount of momentum of inertia to the mirror. There is no lower limit to the size of the
stiffening ribs as the previous experiments show structures as narrow as 3 µm can be
bonded to another layer.
(3) Integration of scanning micromirrors with other parts of the communication
platform. A feedback control system for MEMS micromirrors is implemented by
measuring the mirror position electronically with the sense capacitors [67]. However,
beam-steering using gyro-stabilized MEMS scanning micromirrors still needs to be
implemented and integrated with imaging receiver to realize the beam acquisition and
link maintenance between two micro air vehicles.
(4) Application of scanning micromirrors in other areas. Besides free space optical
communication, there are a number of applications in which scanning micromirrors are
used. Having two-axis scanning capability and large scanning range, our scanning
micromirrors can be used for laser printer, projection video displayer, and other fiber
optic equipment, such as tunable lasers and fiber-optic switches.
(5) Improvement of the SOI/SOI wafer bonding process. More bonding layers can be
added in the process to eliminate the timed etching step completely. Realizing low
temperature silicon direct bonding between SOI wafers will give much flexibility to the
process such as fabricating bonded transducers and sensors over existing CMOS devices.
Methods such as oxygen plasma activation and/or tetramethoxysilane (TMOS) solution
105
MEMS SCANNING MICROMIRROR
dip can decrease the annealing temperature (≤ 500°C) while achieving bonding energies
that are sufficiently high for a micromechanical device.
(6) Application of the SOI/SOI wafer bonding process to other transducers and
sensors. MEMS micro engines and pressure sensors are two devices under active
investigation that employ silicon direct bonding. Wafer packaging realized by silicon
wafer bonding is the key enabling micromachining technology for the high-volume
production of low-cost MEMS components and systems. The SOI/SOI wafer bonding
process may play a role when several bonding layers with strict control over their
thicknesses are required.
Proof Mass
g
Anchor
Torsional Beam
Torsional Beam
Gap-Closing Sensing Comb Fingers
Proof Mass
g
Anchor
Torsional Beam
Torsional Beam
Gap-Closing Sensing Comb Fingers
Figure 5-1. Schematic of proposed accelerometer over the out-of-plane axis with
high sensitivity and resolution.
An accelerometer with high sensitivity and resolution over the out-of-plane axis can
be realized by the SOI/SOI wafer bonding process, as proposed in Figure 5-1. The out-of-
106
MEMS SCANNING MICROMIRROR
plane acceleration of the proof mass, which consists of both the device layer and the
substrate of the SOI wafer, is translated into the in-plane movement of gap-closing comb
fingers. Gap-closing capacitive sensing can be employed for the purpose of maximizing
sensitivity while lateral comb sensing is a better choice to achieve larger range and higher
linearity. Combining with accelerometers sensing two other axis’ movement, this makes
a single-chip monolithic three-axis accelerometer with equally high sensitivity over all
axes.
107
REFERENCE
REFERENCE:
[1] C. DeCusatis, “Optical data communication: fundamentals and future directions,”
Optical Engineering, vol. 37, no. 12, P3082-99, 1998.
[2] A. Acampora, “Last mile by laser,” Scientific American (International Edition), vol.
286, no. 7, P32-7, 2002.
[3] W. R. Leeb, “Laser space communications: systems, technologies, and applications,”
Review of Laser Engineering, vol. 28, no. 12, P804-8, 2000.
[4] M. R. Garcia-Talavera, S. Chueca, A. Alonso, T. Viera, Z. Sodnik, “Analysis of the
preliminary optical links between ARTEMIS and the optical ground station,”
Proceedings of Spie - the International Society for Optical Engineering, vol. 4821,
P33-43, 2002.
[5] J. M. Kahn, “Secure free-space optical communication between moving platforms,”
Proceedings of the 15th Annual Meeting of the IEEE Lasers and Electro-Optics
Society, vol. 2, P455-6, 2002.
[6] M. Last, B. S. Leibowitz, B. Cagdaser, A. Jog, L. Zhou, B. Boser, K. S. J. Pister,
“Toward a wireless optical communication link between two small unmanned aerial
vehicles,” Proceedings of IEEE International Symposium on Circuits and Systems,
Bangkok, Thailand, 2003.
[7] O. Solgaard, D. Lee, Y. Kyoungsik, U. Krishnamoorthy, K. Li, J. P. Heritage,
“Microoptical phased arrays for spatial and spectral switching,” IEEE
Communications Magazine, vol. 41, no. 3, P96-102, 2003.
[8] P. B. Ruffin, “Optical MEMS-based arrays,” Proceedings of Spie - the International
Society for Optical Engineering, vol. 5055, P230-41, 2003.
[9] B. A. Warneke, M. Last, B. Liebowitz, K. S. J. Pister. “Smart Dust: communicating
with a cubic-millimeter computer,” Computer, vol. 34, no. 1, P44-51, 2001.
[10] A. Mason, N. Yazdi, A. V. Chavan, K. Najafi, K. D. Wise, “A generic multielement
108
REFERENCE
microsystem for portable wireless applications,” Proceedings of IEEE, vol. 86, no. 8,
P1733-46, 1998.
[11] G. Asada, M. Dong, T. S. Lin, F. Newberg, G. Pottie, W. J. Kaiser, H. O. Marcy,
“Wireless integrated network sensors: low power systems on a chip,” Proceedings of
the 24th European Solid State Circuits Conference, P9-16, 1998.
[12] J. M. Rabaey, J. Ammer, T. Karalar, S. Li, B. Otis, M. Sheets, T. Tuan, “PicoRadios
for wireless sensor networks: the next challenge in ultra-low-power design”,
Proceedings of 2002 IEEE International Solid-State Circuits Conference, P200-1,
2002.
[13] K. Brendley, R. Steeb, “Military applications of microelectromechanical systems,”
Rand Report, Rand, Santa Monica, CA 1993.
[14] B. A. Warneke, M. D. Scott, B. S. Leibowitz, L. Zhou, C. L. Bellew, J. A. Chediak,
J. M. Kahn, B. E. Boser, K. S. J. Pister, “An autonomous 16 mm3 solar-powered
node for distributed wireless sensor networks,” Sensor 2002, Orlando, Florida, 12-14
June 2002.
[15] K. S. J. Pister, M. W. Judy, S. R. Burgett, R. S. Fearing, “Microfabricated hinges,”
Sensors and Actuators A (Physical), vol. A33, no. 3, P249-56, 1992.
[16] E. E. Hui, R. T. Howe, M. S. Rodgers, “Single-step assembly of complex 3-D
microstructures,” Proceedings of the 13 IEEE th International Conference on Micro
Electro Mechanical Systems, P602-7, 2000.
[17] D. S. Gunawan, L. Y. Lin, K. S. J. Pister, “Micromachined corner cube reflectors as
a communication link,” Sensors and Actuators A, 46/47, P580-3, 1995.
[18] P. B. Chu, N. R. Lo, E. C. Berg, K. S. J. Pister. “Optical communication using micro
corner cube reflectors,” Proc. of IEEE Micro Electro Mechanical Systems Workshop,
P350-5, Nagoya, Japan, 1997.
[19] G. Lin, C. J. Kim, S. Konishi, H. Fujita, “Design, fabrication, and testing of a C-
shape actuator,” Proceedings of the 8th International Conference on Solid-State
Sensors and Actuators and Eurosensors IX, vol. 2, P416-9, 1995.
109
REFERENCE
[20] T. Ebefors, E. Kalvesten, G. Stemme, “New small radius joints based on thermal
shrinkage of polyimide in V-grooves for robust self-assembly 3D microstructures,”
Journal of Micromechanics and Microengineering, vol. 8, no. 3, P188-94, 1998.
[21] R. R. A. Syms, C. Gormley, S. Blackstone, “Improving yield, accuracy and
complexity in surface tension self-assembled MOEMS,” Sensors and Actuators A,
vol. 88, P273-83, 2001.
[22] R. R. A. Syms, “Surface tension powered self-assembly of 3-D micro-
optomechanical structures,” Journal of Microelectromechanical Systems, vol. 8, no.
4, P448-55, 1999.
[23] L. Zhou, J. M. Kahn, K. S. J. Pister, "Corner-cube retroreflectors based on structure-
assisted assembly for free-space optical communication", IEEE Journal of MEMS,
vol. 12, no. 3, P233-42, 2003.
[24] J. Walko, “BT improves fiber-laser link,” Photonics, P26-8, 1995.
[25] C. Strandman, Y. Backlund, “Passive and fixed alignment of devices using flexible
silicon elements formed by selective etching,” Journal of Micromechanics and
Microengineering, vol. 8, no. 1, P39-44, 1998.
[26] D. J. Bishop, C. R. Giles, S. R. Das, “The rise of optical switching,” Scientific
American, P74-9, January 2001.
[27] G. A. Feather, D. W. Monk, “Digital micromirror device for projection display,”
Proceedings of Spie - the International Society for Optical Engineering, vol. 2407,
P90-5, 1995.
[28] M.-H. Kiang, O. Solgaard, R. S. Muller, K. Y. Lau, “Micromachined polysilicon
microscanners for barcode readers,” IEEE Photonics Technology Letters, vol. 8, no.
12, P1707-9, 1996.
[29] M. A. Helmbrecht, U. Srinivasan, C. Rembe, R. T. Howe, R. S. Muller,
“Micromirrors for adaptive-optics arrays,” Proceedings of the 11th International
Conference on Solid-State Sensors and Actuators, vol. 2, P1290-3, 2001.
[30] J. D. Berger, D. Anthon, H. Jerman, “External cavity diode lasers tuned with silicon
110
REFERENCE
MEMS,” Semiconductor International, vol. 25, no. 2, Psupl8-14, 2002.
[31] R. Conant, J. Nee, K. Lau, R. Muller, "A fast flat scanning micromirror," 2000 Solid-
State Sensor and Actuator Workshop, Hilton Head, South Carolina, P6-9, 2000.
[32] U. Krishnamoorthy, D. Lee, O. Solgaard, “Self-aligned vertical electrostatic
combdrives for micromirror actuation,” Journal of Microelectromechanical Systems,
vol. 12, no. 4, P458-64, 2003.
[33] V. Milanovic, S. Kwon, L. P. Lee, “Monolithic vertical combdrive actuators for
adaptive optics,” Proceedings of 2002 IEEE/LEOS International Conference on
Optical MEMS, P57-8, 2002.
[34] P. R. Patterson, D. Hah, H. Nguyen, H. Toshiyoshi, R. Chao, M. C. Wu, “A scanning
micromirror with angular comb drive actuation,” Proceedings of the 15th IEEE
International Conference on Micro Electro Mechanical Systems, P544-7, 2002.
[35] J. Kim, H. Choo, L. Lin, R. S. Muller, “Microfabricated torsional actuator using self-
aligned plastic deformation,” Proceedings of the 12th International Conference on
Solid-State Sensors and Actuators, Transducers 2003, vol. 2, P1015-8, 2003.
[36] S. Kwon, V. Milanovic, L. P. Lee, “A high aspect ratio 2D gimbaled microscanner
with large static rotation,” Proceedings of 2002 IEEE/LEOS International
Conference on Optical MEMS, P149-50, 2002.
[37] V. Milanovic, G. Matus, T. Cheng, and B. Cagdaser, “Monolithic high aspect ratio
two-axis optical scanners in SOI,” Proceedings of 2003 IEEE MEMS Conference,
P255-8, 2003.
[38] V. Milanovic, M. Last, K. S. J. Pister, “Torsional micromirrors with lateral
actuators,” Proceedings of the 11th International Conference on Solid-State Sensors
and Actuators, Transducers 2001, Munich, Germany, 2001.
[39] O. Degani, and Y. Nemirovsky, “Design considerations of rectangular electrostatic
torsion actuators based on new analytical pull-in expressions”, Journal of
Microelectromechanical Systems, vol. 11, no. 1, P20-26, 2002.
111
REFERENCE
[40] L. Doherty, B. A. Warneke, B. E. Boser, and K. S. J. Pister, “Energy and
performance considerations for Smart Dust”, International Journal of Parallel and
Distributed Systems, vol. 4, no. 3, P121-33, 2001.
[41] X. Zhu, V. S. Hsu, and J. M. Kahn, “Optical modeling of MEMS corner-cube
retroreflectors with misalignment and non-flatness”, IEEE Journal on Selected
Topics in Quantum Electronics, vol. 48, no. 1, P26-32, 2002.
[42] X. Zhu, J. M. Kahn, “Free-space optical communication through atmospheric
turbulence channels,” IEEE Transactions on Communications, vol. 50, no. 8, P1293-
300, 2002.
[43] M. Born, and E. Wolf, Principles of Optics, Sixth Edition, Pergamon Press, 1980.
[44] C. L. Bellew, S. Hollar, and K.S.J. Pister, “An SOI Process for Fabrication of Solar
Cells,” Proceedings of the 12th International Conference on Solid-State Sensors and
Actuators, Transducers 2003, Boston, USA, P1075-9, 2003.
[45] MLB Corporation, 137 Lundy Lane, Palo Alto, CA 94306. (650) 424-9552.
http://www.spyplanes.com
[46] K. Somasundram, D. Cole, C. McNamara, A. Boyle, P. McCann, C. Devine, A.
Nevin, “Fusion-bonded multilayer SOI for MEMS applications,” Proceedings of
Spie - the International Society for Optical Engineering, vol. 5116, P12-9, 2003.
[47] F. S. D’aragno, T. Iwamoto, H. D. Chiou, A. Mirza, “A Study of Silicon Direct
Wafer Bonding for MEMS Application,” Proceedings of the 4th International
Symposium on Semiconductor Wafer Bonding: Science, Technology, and
Applications, vol. 97-36, P127-37, 1998.
112
REFERENCE
[48] Brown, G. O'Neill, S. Blackstone, “Single-crystal Micromachining Using Multiple
Fusion-Bonded Layers,” Proceedings of Spie - the International Society for Optical
Engineering, vol. 4174, P406-15, 2000.
[49] Q.-Y. Tong, U. Gosele, Semiconductor Wafer Bonding: Science and Technology, P2,
1999.
[50] G. Krauter, A. Schumacher, U. Gosele, “Low temperature silicon direct bonding for
application in micromechanics: bonding energies for different combinations of
oxides”, Sensors and Actuators A (Physical), vol. 70, P271-5, 1998.
[51] P. W. Barth, “Silicon fusion bonding for fabrication of sensors, actuators and
microstructures,” Sensors and Actuators A (Physical), vol. 23, no. 1-3, P919-26,
1990
[52] Q.-Y. Tong, U. Gosele, “A model of low-temperature wafer bonding and its
applications,” Journal of the Electrochemical Society, vol. 143, no. 5, P1773-9,
1996.
[53] M. Schmidt, “Wafer-to-wafer bonding for microstructure formation,” Proceedings of
the IEEE, vol. 86, no. 8, P1575-85, 1998.
[54] H. C. Liu, S. P. Murarka, “Elastic and viscoelastic analysis of stress in thin films,”
Journal of Applied Physics, vol. 72, no. 8, P3458-63, 1992.
[55] M. M. Visser, S. Weichel, R. de Reus, A. B. Hanneborg, “Strength and leak testing
of plasma activated bonded interfaces,” Sensors and Actuators A (Physical), vol. 97-
98, no. 1, P434-40, 2002.
[56] S. P. Timoshenko, Theory of Plates and Shells, New York: McGraw-Hill, 1959.
113
REFERENCE
[57] R. D. Cook, W. C. Young, Advanced Mechanics of Materials, Macmillan, 1985.
[58] W. C. Young, R. G. Budynas, Roark’s Formulas for Stress and Strain, 7th edition,
McGraw-Hill, 2002.
[59] L. Ruoff, “On the ultimate yield strength of solids”, Journal of Applied Physics, vol.
49, no. 1, P197-200, 1978.
[60] K. S. Chen, A. A. Ayon, X. Zhang, S. M. Spearing, “Effect of Process Parameters on
the Surface Morphology and Mechanical Performance of Silicon Structures after
Deep Reactive Ion Etching (DRIE),” Journal of Microelectromechanical Systems,
vol. 11, no. 3, P264-75, 2002.
[61] L. Zhou, M. Last, V. Milanovic, J. M. Kahn, K. S. J. Pister, “Two-Axis Scanning
Mirror for Free-Space Optical Communication between UAVs”, IEEE/LEOS Optical
MEMS, Hawaii, USA, Aug. 2003.
[62] V. T. Srikar, S. D. Senturia, “The reliability of microelectromechanical systems
(MEMS) in shock environments,” Journal of Microelectromechanical Systems, vol.
11, no. 3, P206-14, 2002.
[63] J. R. Brockenbrough, S. Suresh, J. Duffy, “An analysis of dynamic fracture in
microcracking brittle solids,” Philosophical Magazine A-Physics of Condensed
Matter Defects & Mechanical Properties, vol. 58, no. 4, P619-34, 1988.
[64] L. Muller, A. P. Pisano, R. T. Howe, “Microgimbal Torsion Beam Design Using
Open, Thin-Walled Cross Sections,” Journal of Microelectromechanical Systems,
vol. 10, no. 4, P550-60, 2001.
[65] R. Legtenberg, A. W. Groeneveld, M. Elwenspoek, “Comb-Drive Actuators for
114
REFERENCE
Large Displacements,” Journal of Micromechanics and Microengineering, vol. 6,
no. 3, P320-9, 1996.
[66] J. D. Grade, H. Jerman, T. W. Kenny, “Design of Large Deflection Electrostatic
Actuators,” Journal of Microelectromechanical Systems, vol. 12, no. 3, P335-43,
2003.
[67] B. Cagdaser, A. Jog, M. Last, B. S. Leibowitz, L. Zhou, E. Shelton, K. S. J. Pister, B.
E. Boser, “Capacitive Sense Feedback Control for MEMS Beam Steering Mirrors,”
2004 Solid-State Sensor and Actuator Workshop, Hilton Head, South Carolina,
P348-51, 2004.
115
APPENDIX
APPENDIX A – MATLAB SCRIPTS TO MODEL FAR-FIELD
IMAGE PATTERN REFLECTED BY CCRS
% This MATLAB program calculates the far field image pattern reflected by a CCR.
% (theta, fai) is the direction of the incident light.
% (x0, y0), (x1, z1), (y2, z2) represent the size of three side mirror planes.
% Effarea(x, y) represents the effective area of CCR reflection.
% I(u,v) is proportional to the light intensity reflected by the CCR along direction (u,v).
clear;
lamda = 0.6328; klamda = 2*pi/lamda; % define the wavelength of the incident light.
% define the direction of the incident light. In this case, it’s the body diagonal direction.
theta = acos(1/sqrt(3)); fai = pi/4;
a = sin(theta)*cos(fai); b = sin(theta)*sin(fai); c = cos(theta);
% define the size of three side mirror planes with unit of um.
x0 = 640; y0 = 450; x1 = 750; z1 = 600; y2 = 750; z2 = 600;
size_max = max([x0,y0,x1,z1,y2,z2]);
% define the size of the far field image plane.
angle_size = 0.01; angle_step = 0.0001;
u = -angle_size:angle_step:angle_size;
v = -angle_size:angle_step:angle_size;
[u,v] = meshgrid(u,v); U = zeros(size(u));
% calculate the effective area (Effarea) of the CCR reflection.
plane_size = 2*size_max; plane_step = 10;
plane_num = plane_size/plane_step;
Effarea = zeros(plane_num+1, plane_num+1);
116
APPENDIX
xmin = sqrt(1-b^2)*min([y0; z1*b/c; y2+z2*b/c]);
ymin = sqrt(1-a^2)*min([x0; x1+z1*a/c; z2*a/c]);
zmin = sqrt(1-c^2)*min([x0*b/a+y0; x1*b/a; y2]);
c1 = b/a*sqrt(1-b^2)/sqrt(1-a^2);
c2 = c/sqrt(1-b^2)/sqrt(1-a^2);
c3 = a*b/sqrt(1-b^2)/sqrt(1-a^2);
for j = -plane_num/2:plane_num/2
x = j*plane_step;
xfactor1 = c1*x;
xfactor2 = c3*x;
x_orth = c2*x;
for k = -plane_num/2:plane_num/2
y = k*plane_step;
z = y-xfactor1;
y_orth = y-xfactor2;
if abs(y) < xmin
if abs(x) < ymin
if abs(z) < zmin
Effarea(j+plane_num/2+1,k+plane_num/2+1) = 1;
U = U+exp(-i*klamda*(x_orth.*u+y_orth.*v));
end;
end;
end;
end;
end;
mesh(Effarea); % draw the effective area of CCR reflection.
I = abs((U*plane_step^2*c2*10^(-6)/lamda).^2);
figure; imshow(I, [], 'notruesize'); colormap(jet); colorbar % draw the far-field pattern.
117
APPENDIX
APPENDIX B – MATLAB SCRIPTS TO MODEL DSCS RELATED
WITH MISALIGNMENT ANGLE OF CCRS
% This program calculates the relationship between DSCS and the misalignment angle.
% misalign is the misalignment angle between two mirrors of CCRs.
% (theta, fai) is the direction of the incident light.
% (x0, y0), (x1, z1), (y2, z2) represent the size of three side mirror planes.
% count is the electrical field of the light reflected by the misaligned CCR along the
direction of the incident light.
% DSCS is the light intensity reflected by the misaligned CCR along the direction of the
incident light.
clear;
misalign = 0:0.0001:0.005; % define the misalignment angle between two mirrors.
lamda = 0.6328;
klamda = 2*pi/lamda;
% define the direction of incident light. In this case, it's the body diagonal direction.
theta = acos(1/sqrt(3));
fai = pi/4;
a = sin(theta)*cos(fai);
b = sin(theta)*sin(fai);
c = cos(theta);
% define the size of three side mirror planes with unit of um.
x0 = 640; y0 = 450; x1 = 750; z1 = 600; y2 = 750; z2 = 600;
size_max = max([x0,y0,x1,z1,y2,z2]);
plane_size = 2*size_max;
plane_step = 10;
118
APPENDIX
plane_num = plane_size/plane_step;
xmin = sqrt(1-b^2)*min([y0; z1*b/c; y2+z2*b/c]);
ymin = sqrt(1-a^2)*min([x0; x1+z1*a/c; z2*a/c]);
zmin = sqrt(1-c^2)*min([x0*b/a+y0; x1*b/a; y2]);
c1 = b/a*sqrt(1-b^2)/sqrt(1-a^2);
c2 = c/sqrt(1-b^2)/sqrt(1-a^2);
c3 = a*b/sqrt(1-b^2)/sqrt(1-a^2);
count = 0;
for j = -plane_num/2:plane_num/2
x = j*plane_step;
xfactor1 = c1*x;
xfactor2 = c3*x;
x_orth = c2*x;
for k = -plane_num/2:plane_num/2
y = k*plane_step;
z = y-xfactor1;
y_orth = y-xfactor2;
if abs(y) <= xmin
if abs(x) <= ymin
if abs(z) <= zmin
count = count+exp(-i*klamda*abs(y*c/sqrt(1-b^2))*2.*sin(misalign));
end;
end;
end;
end;
end;
dscs = abs(count*plane_step^2*c2*10^(-6)/lamda).^2;
figure;
plot(misalign,dscs);
title('DSCS vs. Misaligned Angle'); xlabel('Misaligned Angle (rad)'); ylabel('DSCS');
119
APPENDIX
APPENDIX C – SOI/SOI WAFER BONDING PROCESS FLOW
This appendix provides a detailed description of the SOI/SOI wafer bonding process
flow, the design rules, and a few processing features.
SCS
bonding layer
shallow trench
Buried Oxide
low_SCSdeep trench
high_SCS
SOI2
SOI50
SCS
bonding layer
shallow trench
Buried Oxide
low_SCSdeep trench
high_SCS
SOI2
SOI50
Fig. A.1: Cross section of a device after the backside patterning of bonded wafer.
C1. Layout Features / Design Rules
Put large-radius rounded corner to every mechanical connections whenever possible
in order to reduce the stress concentration.
Add floating structures to decrease the area of open oxide membrane.
Have substrate holes under structures where high voltage is applied to.
Design rule has to take care of the fact that the bonding alignment accuracy achieved
by Karl Suss aligner is within ± 15 µm.
120
APPENDIX
Thermal stress from oxide membrane causes cracks or even breaks off part of the
membrane during and after DRIE handle wafer etch. This sets the narrowest pushing
beam defined by shallow trench.
Alignment tolerance between deep trench and shallow trench: ± 6 µm.
Alignment tolerance between deep trench and substrate pattern: ± 20 µm.
Alignment tolerance between deep trench and bonding layer: ± 15 µm.
Narrowest torsion beam defined by deep trench: 4 µm.
Narrowest pushing beam defined by shallow trench: 10 µm.
Minimum gap distance for comb drive actuator: 2 µm.
C2. Detailed Process Flow
The detailed process flow is listed here and the names in parenthesis indicate the
machine and recipe names used in U. C. Berkeley Microlab.
1. starting wafers: SOI50 and SOI2.
one SOI wafer with 50 µm device layer, 1~2 µm buried oxide layer and 350 ~ 400
µm substrate layer, named SOI50; one SOI wafer with 2 µm device layer, 1 µm
buried oxide layer and 350 ~ 400 µm substrate layer, named SOI2.
2. SOI50: standard clean (sink8/sink6) and MOS tube wet oxidation.
The thickness of oxidation layer depends on the thickness of buried oxide, 7500 Å
for wafers with 1 µm’s buried oxide layer, and 1500 Å for 2 µm’s.
3. SOI50: deep trench lithography (10:1 stepper, chrome mask).
10 mins’ hard bake at 120°C (hard bake oven), 5 mins’ HMDS (sink5), 1.6 µm I-
line photo resist spin-on (svgcoat), mask exposure (gcaws), post exposure bake for 60
121
APPENDIX
secs (svgdev), photo resist develop, discum (technics-c), hard bake for 45 mins ~ 2
hours (hard bake oven).
4. SOI50: deep trench pattern transfer on oxidation layer.
oxide etching (lam2), photo resist strip with PRS3000 (sink5).
5. SOI50: backside alignment mark patterning (contact, chrome mask).
spin coat a layer of 1.6 µm protection photo resist on the front side of the wafer
first, 1.6 µm I-line photo resist lithography on the back of the wafer, backside
alignment mask exposure (ksaligner with soft contact mode), hard bake, oxide
etching (lam2), photo resist strip with PRS3000 (sink5).
6. SOI50: shallow trench mask patterning (contact, emulsion mask).
1.6 µm I-line photo resist lithography on the front side of the wafer, shallow
trench mask exposure (ksaligner with vacuum contact mode).
7. SOI50: deep reactive ion etching.
sts etching by VEE1 program for 20 minutes until deep trench is around 30 µm
thick, PRS3000 strip off shallow trench photo resist, sts etching by VEE1 program for
10 minutes, continued with ANITA1B program (about 15 minutes) until all trenches
are clear and low_SCS layer is about 6 µm thick.
8. SOI50: strip off front side oxidation mask by HF.
standard clean (sink8/sink6), coat SOI50 backside with thick photo resist to
protect the alignment mark (svgcoat1), hard bake for three hours (hard bake oven),
10:1 HF etching for 45 minutes until all front side oxide is gone and the exposed
buried oxide is around 6000 Å (or more accurately, calculate the etching time by
using the etching speed of 230 Å/min, don’t disturb the dish mechanically during the
122
APPENDIX
etching, otherwise, photo resist is easy to peel off from the coated surface), PRS3000
photo resist strip.
9. SOI2: standard clean (sink8/sink6) and MOS tube wet oxidation.
the thickness of oxidation layer is 1000 Å ~ 3000 Å.
10. SOI2: bonding layer mask patterning (10:1 stepper, chrome mask).
1.6 µm I-line photo resist lithography on the front side of the wafer as in step 3,
oxide etching (lam2, no need to strip off photo resist at this stage).
11. SOI2: deep reactive ion etching.
sts etching by Anita1B program for 2 minutes, strip off photo resist with PRS3000.
12. SOI2: strip off front side oxidation mask by HF.
standard clean (sink8/sink6), 10:1 HF etching for 22 minutes until all front side
oxide is gone and the exposed buried oxide is around 5000 Å (or more accurately, to
calculate the etching time by using the etching speed of 230 Å/min).
13. SOI50 and SOI2: standard clean (sink8/sink6), HF 25:1 dip for 25 seconds and RCA
clean with DI water in between.
modified RCA1 (NH4OH : H2O2 : H2O = 0.01-0.25 : 1 : 5) cleaning for 10 ~ 20
minutes, RCA2 (HCl : H2O2 : H2O = 1 : 1 : 6 to 1 : 2 : 8) cleaning for 20 ~ 40
minutes.
14. SOI50 and SOI2: bond with alignment.
pre-fusion bonding (ksba6), with prevac time = 30 seconds, fullvac time = 30
seconds, purge time = 10 seconds.
15. Bonded SOI50/SOI2: anneal in non-MOS tube for 10 hours at 1050°.
123
APPENDIX
check the bonding quality with IR scope and check the alignment accuracy with
Quintel.
16. Bonded SOI50/SOI2: deep reactive ion etching to have partial of front side handle
wafer released.
sts etching by BORIS02/VEE6 program for about 140 minutes or until the
thickness of the front side handle layer is decreased to 100 µm (no need to have an
extra handle wafer attached to the bonded wafer).
17. Bonded SOI50/SOI2: substrate lithography (contact, chrome mask).
8 µm thick photo resist lithography on the backside of the wafer, substrate pattern
exposure (ksaligner with soft contact mode).
18. Bonded SOI50/SOI2: handle wafer attachment for sts etching.
coat the handle wafer with 8 µm thick photo resist without soft bake, attach it to
the frontside of the bonded wafer manually, primeoven to expose to the vacuum, hard
bake for 3 hours.
19. Bonded SOI50/SOI2: deep reactive ion etching to etch backside substrate wafer.
sts etching by VEE6 program for about 140 minutes or until the pattern on the
backside wafer is cleared.
20. Bonded SOI50/SOI2: dicing.
8 µm thick photo resist protection on the backside of the wafer, dice to single dies
(disco, mode A with z step = 0.5 mm), PRS3000 overnight to release the bonded
chips from the sts handle wafer, piranha cleaning.
21. Die: front side handle wafer full release.
124
APPENDIX
coat a handle wafer with 8 µm thick photo resist glue layer, attach it to the
backside of the diced chip, primeoven to expose it to the vacuum, hard bake for three
hours, sts VEE6 etching until all front side gone.
22. Die: debond with handle wafer and HF release.
PRS3000 to debond the chip with the handle wafer, piranha cleaning, 5:1 BHF for
twelve minutes.
23. Die: package with westbond.
wirebond (westbond), set second clamping option, i.e. drop before clamp, to 0, the
power and time for bond 1 on Au to be 300 mW and 30 ms, bond 2 on Si to be 370
mW and 30 ms, bonding force to be 31 grams (note that the maximum power to apply
on Si is 470 mW).
125
APPENDIX
APPENDIX D – ANSYS SCRIPTS TO MODEL MECHANICS OF
SCANNING MICROMIRRORS
! ANSYS script to simulate the rotation angle under the lateral actuation force.
/batch, list
/prep7, Use T-bar as torsional beam
et, 1, 92 ! solid92 element for meshing structures
mat, 1
mpread, si_blk_ln, si_mpl, , lib
! dimensions (microns) / parameters
bl = 300 ! Beam web length (Bonding layer)
btw = 3 ! Beam web height (Bonding layer)
bb = 70 ! Beam web width (Bonding layer)
btf = 3 ! Beam flange width (High_SCS layer)
bh = 50 ! Beam flange height (High_SCS layer)
pl = 300 ! Push beam (Low_SCS layer)
ph = 6 ! Push height (Low_SCS layer)
pw = 10 ! Push width (Low_SCS layer)
fymag = 3 ! Magnitude of lateral actuation force
! Create model
block, -bl-50, -50, -bb/2, bb/2, 0, btw ! Create torsional beam web 1
block, 50, bl+50, -bb/2, bb/2, 0, btw ! Create torsional beam web 2
block, -bl-50, -50, -btf/2, btf/2, -bh, 0 ! Create torsional beam flange 1
block, 50, bl+50, -btf/2, btf/2, -bh, 0 ! Create torsional beam flange 2
block, -30, 30, 0, 200, -bh, btw ! Create a dummy to show the rotation of the beam
block, -pw/2, pw/2, -pl, 0, -50, -50+ph ! Create pushing arm
block, -50, -30, -bb/2, 200, -bh, btw ! Create linkage between pushing and torsion beam
126
APPENDIX
block, 30, 50, -bb/2, 200, -bh, btw ! Create linkage between pushing and torsion beam
vglue, all
! Apply displacement boundary condition
da, 17, ALL, 0 ! Left side of the left torsional beams should be restricted
da, 54, ALL, 0
da, 24, ALL, 0 ! Right side of the right torsional beams should be restricted
da, 57, ALL, 0
da, 33, ux, 0 ! The lower end of pushing arm move only laterally in y direction
da, 33, uz, 0
fk, 42, fy, fymag/4 ! Acutating force is symmetrically acted on the pushing arm
fk, 44, fy, fymag/4
fk, 45, fy, fymag/4
fk, 46, fy, fymag/4
vsel, all ! Select all volumes
vatt, 1, , 1
smrtsiz, 2
vmesh, all ! Mesh all the structures
finish
! Commands for nonlinear analysis
/solu
antype, 0
nlgeom, on
autots, on
nsubst, 2, 100, 1
autots, 1
outres, NSOL, 1
solve ! Solve the problem
finish
127
APPENDIX
APPENDIX E – MATLAB SCRIPTS TO CALCULATE THE
CURVATURE OF A MULTILEVEL WAFER
% This program searches the optimal thickness of the oxide added on the backside of an
SOI wafer, so that the bow of the wafer induced by thermal stress is at its
minimum.
% Layer 1, 2, 3, 4 are the device layer, buried oxide layer, handle wafer, and the oxide
layer added on the backside of the SOI wafer.
t4 = 1e-8:1e-8:2e-6; % t4 is the thickness of the added oxide layer.
r = stress2(t4); % calculate the curvature of the multilayer wafer.
bow = 8100/8./r; % calculate the bow of the multilayer wafer
figure;
plot(t4*1e6, bow);
title('Bow of wafer vs. thickness of oxide under the handle wafer');
xlabel('Thickness of oxide under the handle wafer (\it\mum)');
ylabel('Bow of wafer (\it\mum)');
function r = stress2(t4)
t1 = 50e-6; % t1, t2, t3, t4 are the thickness of the individual layers.
t2 = 2e-6;
t3 = 350e-6;
mui1 = 0.12; % Poisson's ratio of Si;
mui2 = 0.2; % Poisson's ratio of SiO2;
mui3 = mui1;
mui4 = mui2;
alpha1 = 2.6e-6; % Coefficient of thermal expansion of Si;
alpha2 = 0.5e-6; % Coefficient of thermal expansion of SiO2;
alpha3 = alpha1;
alpha4 = alpha2;
128
APPENDIX
delta_T = 1000;
E1 = 160e9; % Young's modulus of Si;
E2 = 160e9; % Young's modulus of SiO2;
E3 = E1;
E4 = E2;
E1_bi = E1/(1-mui1);
E2_bi = E2/(1-mui2);
E3_bi = E3/(1-mui3);
E4_bi = E4/(1-mui4);
B = [0; 0; alpha2*delta_T-alpha1*delta_T; alpha3*delta_T-alpha2*delta_T;
alpha4*delta_T-alpha3*delta_T];
[m, n] = size(t4);
r = zeros(m, n);
for ii = 1:m
for jj = 1:n
A = [1 1 1 1 0; t1/2 t1+t2/2 t1+t2+t3/2 t1+t2+t3+t4(ii, jj)/2
E1_bi*t1^3/12+E2_bi*t2^3/12+E3_bi*t3^3/12+E4_bi*t4(ii, jj)^3/12;
1/E1_bi/t1 -1/E2_bi/t2 0 0 t1/2+t2/2; 0 1/E2_bi/t2 -1/E3_bi/t3 0 t2/2+t3/2;
0 0 1/E3_bi/t3 -1/E4_bi/t4(ii, jj) t3/2+t4(ii, jj)/2];
x = A\B; % Linear equation solves the curvature of SOI wafer.
r(ii, jj) = 1/x(5);
end;
end;
129