The Easy to Use Deep Cleanerwith automatic tool conversion
Review this manual before operating deep cleaner
Owner’sManual
These models are included in this manual
Deluxe Models
™
PlusModels
SteamVac™ Deep Cleaner cleans carpet fibers byapplying hot tap water and cleaning solution.www.hoover.com
• Use indoors only.• Use only on surfaces moistened by the cleaning process or small spills. Do
not immerse product.• Connect to a properly grounded outlet only. See “Grounding Instructions”.• Do not clean over floor electrical outlets.• Do not use without tanks in place.• Use extra care when cleaning on stairs. Do not place deep cleaner on stairs.• Use deep cleaner only for its intended use as described in the instructions.• Use only attachments recommended by The Hoover Company; others may
cause hazards.• The use of an extension cord Is not recommended. If an extension cord is
absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-prong grounding type plug and a 3-pole receptacle that accepts the machine plug.
• Unplug deep cleaner when not in use. Turn off all controls before unplugging.• Unplug before connecting the powered hand tool.• Always disconnect cord from electrical outlet before servicing the deep cleaner.• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.• Never handle plug or appliance with wet hands.• Do not pull or carry by cord, use cord as a handle, close door on cord or pull
cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not use with damaged cord or plug. If appliance Is not working as it should, has been dropped, damaged, left outdoors, or dropped Into water, takeit to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer.
• Close supervision is necessary when any appliance is used by or near children. Do not allow deep cleaner to be used as a toy or to run unattended atany time.
• Do not point tools toward people or pets.• Use only commercially available floor cleaners Intended for machine
application. Do not use any type of wax with deep cleaner.• To assist In reducing drying time, be certain the area Is well ventilated when
using detergents and other cleaners with this machine.• Keep detergents and other cleaners out of children's reach.• Do not use to pick up flammable or combustible liquids such as gasoline or
use In areas where they may be present.• Do not pick up chlorine bleach, drain cleaner, gasoline or any other toxic
material with this appliance.• Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.• Avoid picking up hard, sharp objects with the deep cleaner. They may damage
the machine.• Keep hair, loose clothing, fingers, feet and all parts of body away from
openIngs and moving parts.• Do not put any object Into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, and anything that may reduce air flow.• To help prevent matting and resoiling, avoid contact with carpets until they are
dry. Keep children and pets away from carpets until they are completely dry.• Store in a dry place. Do not expose machine to freezing temperatures.
Save these instru c t i o n s !
2
Fill in and RetainThis HOOVER deep cleaner isdesigned for deep cleaning carpet,rugs, carpeted stairs and upholstery.The model and serial numbers arelocated on the data label on the backof the handle.
For your personal records, pleaseenter the COMPLETE model and serialnumbers in the spaces provided andretain this information.
Your deep cleaner is model
and has serial number
It is suggested that you attach yoursales receipt to this owner s manual.
Verification of date of purchase maybe required for warranty service ofyour Hoover product.
IndexImportant safeguards . . . . . . . . . . 2Unpacking deep cleaner. . . . . . . . . 3Assembling deep cleaner . . . . . . 4-5Deep cleaner description . . . . . . . . 5General operation . . . . . . . . . . . . 6-8
Filling the clean solution tank .. . 7Emptying the recovery tank . . 7-8Brush speed selector . . . . . . . . . 6Brush Indicator . . . . . . . . . . . . . . 6
How to useBefore you begin . . . . . . . . . . . . 8After cleaning . . . . . . . . . . . . . 8-9Cleaning carpet . . . . . . . . . . . . . 9Picking up spills . . . . . . . . . . . . . 9Using the tools . . . . . . . . . . . . . . 9
Cleaning carpeted stairs . . . 9-11Cleaning upholstery . . . . . . . 10
If you have a problem . . . . . . . . . 12Lubrication . . . . . . . . . . . . . . . . . . 11Service . . . . . . . . . . . . . . . . . . . . . 11Storage . . . . . . . . . . . . . . . . . . . . . 11Warranty . . . . . . . . . . . . . . . . . . . . 12
I m p o rtant Safeguard s !When using an electrical appliance, always follow basic
precaution, including the following:
WARNING: To reduce the risk of fire, electricshock, or injury:
© 2002 The Hoover Companyw w w. h o o v e r. c o m
READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.
3
GroundingInstructions
This appliance must be grounded. If itshould malfunction or breakdown,grounding provides a path of least resis-tance for electrical current to reduce therisk of electric shock. This appliance isequipped with a cord having an equip-ment-grounding conductor (C) andgrounding plug (A). The plug must beplugged into an appropriate outlet (B)that is properly installed and grounded inaccordance with all local codes andordinances.
DANGER-Improper connection of the equipment-grounding conductor can result in therisk of electric shock. Check with a qual-ified electrician or service person if youare in doubt as to whether the outlet isproperly grounded. Do not modify theplug provided with the appliance - if itwill not fit the outlet, have a proper outletinstalled by a qualified electrician. Thisappliance is for use on a nominal 120volt circuit and has a grounding plugthat looks like the plug illustrated insketch (A).
A temporary adapter (D) may be used toconnect this plug to a 2-pole receptacle(E) if a properly grounded outlet is notavailable. The temporary adapter shouldbe used only until a properly groundedoutlet (B) can be installed by a qualifiedelectrician. The green colored rigid ear,lug, or the like (F) extending from theadapter must be connected to a perma-nent ground (G) such as a properlygrounded outlet box cover. Wheneverthe adapter is used, it must be held inplace by a metal screw.
A B
C
D F
G
E
1. Assembly
Unpack deep cleaner from the cartonand identify the parts shown. Removeand dispose of the packing.
A B
C DE
G
H
F
I
1-1
A. Deep cleaner B. Upper handle OR
Upper handle for stair/upholstery nozzle storage*C. Bolts (2) D. Nuts (3 - one extra included) E. Carpet/Upholstery Detergent F. Hose holder
Contained in carton with hose:G. HoseH. Stair/upholstery nozzle
OR utility nozzle*I. Hose rack and screw (taped on rack under nozzle)
*Included with some models
Press cord into cord clip on back ofhandle. Pull cord tight.
4
The assembled cleaner will look like thisdrawing (Plus model shown).
1-2
Attach upper handleRemove clean solution tank (upper tank)from deep cleaner.
With cord hook (A) to back of deep cleaner,push upper handle down onto lower han-dle. Push b o l t s into holes on front of han-dle. If bolts will not go through hole easi-ly handle is not pushed completelyd o w n .
1-3
1-6
1-7
Attach hose holderPosition hose holder (B) onto handle bymatching tabs on rack with openings onback of handle. Make sure holes forbolts are aligned.
1-8 1 - 9
Place nuts in recessed areas on backof the hose holder. Hold each nut inplace while tightening each bolt securely(from the front of the handle) with aPhillips screwdriver.Only two nuts are needed on this model.The extra nut is not required but hasbeen provided for your convenience.
A
C
When handle sections are completelytogether, squeeze trigger (C) on upperhandle to snap trigger rod In place.
Replace clean solution tank (upper tank)by positioning bottom first. Press ontank handle to snap top of tank intoplace.
Attach tool holderRemove tool and taped screw fromholder.Insert projections on rack into slots onback of cleaner.
Assemble handle
1-4
B
1-5
5
1 - 1 0
1 -1 3 1 - 1 5
Slide rack down into place. Insert screwat (D) and tighten with a Phillips screw-driver.
Storing hose & toolsStore hose on rack by first positioninghose in front section of holder.
D
Continue wrapping hose under lowerhook (E). Snap hose end fully into hold-er (F).The hose end must be pushed com-pletely down into holder (F) to ensuremaximum suction when cleaningfloors.
Position tool in holder at base of cleanerand snap it into place as shown at arrow.
For Plus modelsTo store stair/upholstery nozzle, opentool door, place nozzle in bracket and fitit securely into position. To remove,reverse this procedure.
How to reattach toolcoverThe tool cover is designed with a break-away feature which allows it to snap freeif it is pushed open too far.To reattach, align hinges of cover withslots on sides of tool storage area.Push cover down to secure in place.
1 - 1 4
1 - 1 1 1 - 1 2
F
F
E
2. How to use The assembled deep cleaner will look like the drawing.
Deep cleaner description2-1 1
2
4
4
3
6
5
7
7
8
1011
12
13
14
15
16
17
1819 21 20
22
9
6
1. Hand grip2. Solution trigger: press to
release clean solution.3. Cord clip: place cord in clip
to keep it out of the way when using cleaner
4. Hose5. Hose holder: wrap hose
around holder and hooks (6) for storage.
6. Hose hooks7. Cord hooks: wrap cord
around hooks for storage. The top hook can be rotated right or left for quick and easy cord release
8. Stair/upholstery nozzle*9. Carrying handle10. Clean solution tank handle11. Clean solution tank cap/
measuring cup12. Clean solution tank: holds
cleaning solution.13. Recovery tank handle:
raise handle to unlock tank for removal; lower handle forward to lock tank into posi-tion.
14. Recovery tank: holds dirty solution.
15. Hood16. Brush speed selector:
slide selector to set brush speed on HI, LO, or OFF.
17. Brush Indicator: spins when brushes are rotating.
18. Nozzle.19. Cleaning mode indicator:
choose either floor or tools20. ON/OFF pedal21. Handle release pedal: step
on pedal to lower handle to operating (floor) position;
22. Stair/upholstery nozzle OR Utility nozzle*
*Included with some models
This deep cleaner is intendedfor household use. Operatedeep cleaner only at voltagespecified on data plate on backof cleaner. Plug deep cleanerInto a properly grounded outlet.
Continued ➜
6
2-2
ON/OFF pedal &Handle release pedalStep on pedal (A) to turn deep cleaneron. Step on pedal again to turn deepcleaner off.
Step on pedal (B) to lower handle tooperating position. Handle does not lockinto a single position but “floats” to allowconvenient operation.
A B
C
D
Cleaning mode indicatorIndicator will show a green window nextto FLOOR (C) when handle is in theoperating position for cleaning carpetrugs and bare floors.Indicator will show a green window nextto TOOL (D) when handle is in theupright position for tool use on stairsupholstery etc.
Deep cleaner automatically divertssuction from FLOOR to TOOL whenhandle is raised from the operating tothe upright position.
2-3 2-4
2-5 2-6 2-7
2-8 2-9
To transportTo move your deep cleaner from room toroom put handle in upright and lockedposition tilt deep cleaner back onwheels and push forward.
The deep cleaner may also be lifted byplacing a hand under the upper cleansolution tank handle as shown.
Automatic “shut off”When the re c o v e ry tank (lower tank) is fullthe automatic shutoff mechanism will shuto ff the deep cleaner suction (suction willbe noticeably reduced).At that time the red float disk will rise tothe top of the recovery tank lid (E). Thedeep cleaner will no longer pick up dirtysolution and the motor sound willbecome noticeably higher in pitch.When this happens turn deep cleaneroff and empty recovery tank beforecontinuing use.Check clean solution tank also; it mayneed to be refilled.
E
F
G
Brush speed selectorYour ‘SteamVac’ deep cleaner has threeagitator brush settings.Hl - for normal cleaning of carpet andbare floorsLO - for gentle cleaning of carpets andbare floorsOFF - for cleaning carpets and barefloors when brushing is not desired.(Such as when picking up liquid spills.See page 9.)Slide selector button to the desired set-ting before cleaning.
Brush indicatorThe brush indicator will spin (F) whenthe deep cleaner is turned ON and thebrushes are rotating. If the indicator does not spin and thepattern is visible (G) when the deepcleaner is turned ON, the brushes arenot rotating. There are three reasons why the brushesmay not be rotating: 1. Brush speed selector set on OFF (seeprevious section). 2. Handle in upright position (see“CIeaning mode indicator,” p. 6). 3. Brush indicator screen dirty.
H
To clean screen (H), turn deep cleaner offand disconnect from electrical outlet.Remove clear cover and wipe off screenwith a damp cloth. Snap cover back intoposition.
7
2-10
The tanks Clean solution tank (upper tank) The clean solution tank holds the clean-ing solution that is to be dispersed ontothe surface to be cleaned. How to fillDisconnect deep cleaner from electrical outlet.Place deep cleaner handle in theupright, locked position.To remove tank, press down on handleand pull forward.Carry tank to a sink.
2-11 2-12
Rotate tank cap counterclockwise andlift up to remove cap.
Turn cap (A) upside down to serve as ameasuring cup.
5 OUNCES/150 ml
For heavy traffic areas: Pre-treat with HOOVER PreCleanerSpray*.If you do not have access to thePreCleaner Spray*, double the amountof HOOVER Detergent (use 2 capfulsor 10 ounces per 1 gallon tank).
A
Using cap, measure detergent followingthe chart below.For carpet, carpeted stairs and uphol-stery:Fill cap to fill line (5 ounces) with HOOVERCarpet/Upholstery Detergent.Do not use any type of wax with your‘ S t e a m Va c ’deep cleaner.
NOTE: Use only HOOVER detergents.They are specially formulated for usewith your ‘SteamVac’ deep cleaner.
* Available at additional cost if not includedwith your model.
D
C
2-13 2-14CAUTION: Detergents containAnionic and Nonionic Surfactants.Avoid contact with eyes and skin. Incase of contact with eyes, flush withcold water for 15 minutes. In case ofcontact with skin, wash with water. IfIrritation persists, call a physician.For Medical Information (U.S.) call 1-800-752-7869.
Pour detergent into tank. Fill tank tofill line (B) (1 gallon) with hot tapwater.
To assure proper performance, use onlyHOOVER cleaning detergent.
B
If rubber ring (C) on cap has becomedislodged, reposition it with uneven sideagainst ledge (D) as shown.
2-15 2-16
Replace cap. Rotate cap clockwiseuntil it locks In place. Cap must belocked In place for proper perfor-mance and to prevent leaking.
Position bottom of tank into unit andpress on tank handle to snap tank intoplace.
Recovery tank(lower tank)The recovery tank holds the dirty solu-tion that is picked up from the carpet.When the recovery tank is full, the auto-matic shut-off will engage (see page 6)and the tank must be emptied.How to emptyTurn deep cleaner off and disconnectfrom electrical outlet.To prevent possible leaking, removeclean solution tank (Fig. 2-10) by press-ing down on tank handle and pulling for-ward; set tank aside (do not set tankon furniture).Step on handle release pedal (Fig. 2-2)and lower handle until it rests on thefloor. Continued ➜
8
2-17 2-18
Raise handle to carrying position(straight up) to unlock tank from base ofdeep cleaner. Lift tank from deep clean-er and carry it to a sink or drain.
To remove tank lid, lower handle com-pletely toward back of tank and lift offlid.Empty the tank and reposition the lid.
3-1
UNLOCK
For full suction, it is important thatthe recovery tank lid is properlysecured before cleaning.
Raise tank handle to carrying position toplace it into base of cleaner. Move han-dle completely forward to lock tank intoplace (see Fig. 2-17).
Raise handle of deep cleaner to uprightposition and reposition upper cleansolution tank.
3. How to cleanBefore you begincleaninga. Vacuum thoroughly - For carpet,use a vacuum cleaner with an agitatorfor best results. Vacuum upholstery witha vacuum cleaner with cleaning toolattachments. Use a crevice tool to reachinto tufts and folds. Do not use the‘SteamVac’deep cleaner as a dry vac-uum cleaner.b. For upholstery, check cleaningcode - Use your HOOVER ‘SteamVac’deep cleaner only if the upholstery fab-ric is marked with a “W” (for “wet” clean)or “S/W” (for “solvent/dry” or “wet”clean). Do not clean fabric marked“S” (“solvent/dry” clean only). If yourupholstery does not have a code, seekprofessional assistance.c. Test for colorfastness - Mix deterg e n tand water according to the instru c t i o n sunder “Fill clean solution tank” on page 7.
Wet a white absorbent cloth with the solution.In a small, hidden area, gently rub the surf a c ewith the dampened cloth. Wait ten minutesand check for color removal or bleed withwhite paper towel or cloth. If surface hasm o re than one color, check all colors.d. When cleaning entire floor, movefurniture out of area to be cleaned(may not be necessary if only high trafficareas are to be cleaned). For furnituretoo heavy to move, place aluminum foilor wax paper under legs. This will pre-vent wood finishes from staining carpet.Pin up furniture skirts and draperies.e. Pretreat spots and heavy trafficareas with HOOVER ® PreCleaner*- Test PreCleaner for colorfastness by firstspraying it on a hidden area; wait tenminutes and blot with white paper towelsor cloth.If no color change is visible, sprayP reCleaner onto spots and traffic areas. Wa i tat least ten minutes. Use your ‘SteamVa c ’deep cleaner to pick up PreCleaner andspot. Repeat until spot is removed; care f u l l ys c rub with a household scrub brush if nec-e s s a ry.
Do not saturate carpet or upholstery withP re C l e a n e r.If you do not have access to thePreCleaner Spray, double the amountof HOOVER Detergent (use 2 capfulsor 10 oz. per 1 gallon) in the cleansolution tank.No cleaning solution removes all stains fro mall carpets. Stain removal varies with thetype of spill, time elapsed before re m o v a l ,carpet material, and carpet type.f. To prevent staining, use plastic or alu-minum foil to protect wood or metal sur-faces from possible water spray.g. To avoid wetting and possible damageto wood floors underneath area rugs/car-pet, e i t h e r move area rugs/ carpet to a non-wood bare floor surface o r place waterpro o fmaterial (e.g. plastic) underneath themb e f o re cleaning.See pages 9-10 for instructions on variouscleaning tasks.* Available at additional cost if not includedwith your model.
After cleaninga. Allow carpet or upholstery to dry. Tohelp prevent matting and resoiling thecarpet, keep children and pets awayfrom surface until it is completely dry. Ifit is necessary to walk on damp car-pet, place towels or white cloths on thetraffic areas.If furniture must be replaced before thecarpet is dry, use plastic or aluminumfoil pads under legs of furniture so metalslides or wood finishes will not stain thecarpet.b. If desired, the carpet may be rinsed.Rinsing is not necessary for cleaning,but it may Improve the surface’s appear-ance after it is dry.If rinsing is desired, be careful not toover-wet the carpet or upholstery.
Allow time for carpet or upholstery todry completely between cleaning andrinsing. To rinse, follow the same proce-dure for cleaning only using hot tapwater with no detergent in the upperclean solution tank.c. Empty tanks, rinse with clear waterand let air dry. Rinse the solution tankcap and recovery tank lid and let air dry.
d. Remove debris from recovery tank fil-ter and rinse with clean water.Note: If the filter must be removed forcleaning, it is easier to replace if the fil-ter is wet.e. If desired, vacuum thoroughly aftercarpet has completely dried. This willhelp reduce any shading left by thedeep cleaner’s brushes.f. If a tool has been used, remove toolfrom hose and return hose to storageposition. The hose end must bepushed completely down into holderto ensure maximum suction whencleaning floors (Fig. 1-12).
9Continued ➜
Your HOOVER SteamVac deep cleanermay also be used to pick up small liq-uid spills (1 gallon or less, never toexceed 1/4 inch in depth) on carpet,upholstery, or bare floors.
For best results, pick up spills immedi-ately by placing the stair/upholstery noz-zle just above the spill and suction upany residue on top of the carpet. If thespill remains, place either the stair/upholstery nozzle or floor nozzle withbrushes turned OFF in front of the spill,pull the nozzle very slowly over the spillinitially with suction only. Repeat with sprayand suction.When picking up spills on bare floors,use only the floor nozzle with the barefloor attachment in place and speedselector in the OFF position (this will helpp revent spreading the spill).If a spot is left, the stair/upholstery nozzle isgenerally more effective for removing it.Although no cleaning solution can com-pletely remove all spots, they can be tre a t-ed by following the instructions provided bythe manufacturer of the carpet, upholstery,or bare floor surface being cleaned.Do not use the SteamVac deep cleanerto pick up flammable or combustible liq-uids or chemicals.When finished, follow “After cleaning”i n s t ructions on page 8.
3. Dry hands and plug cord into a prop-erly grounded outlet.Do not clean over floor electrical out-lets.4. To avoid walking on damp carpet,start at the end of the room farthest fromthe door or path to sink where tanks willbe emptied and filled .Step on handle release pedal and lowerhandle to operating position; turn deepcleaner ON.5. Squeeze trigger to release cleaningsolution and slowly push deep cleanerforward (equals one wet stroke).
6. Continue to squeeze trigger andslowly pull deep cleaner back toward
To clean the outside of the machine,wipe off dirt with a cloth dampened inwarm water and mild detergent. Do notuse solvent or petroleum based prod-ucts to clean the machine.
Carpet Cleaning
Picking up spills Using the tools
3-2
Read “Before you begin cleaning”instructions on page 8.1. Fill clean solution tank (upper tank)with HOOVER Carpet/UpholsteryDetergent according to instructions onpage 7.2. Move speed selector to LO for gen-tle cleaning or Hl for normal cleaning.
you (second wet stroke). Release triggerand slowly push deep cleaner forwardover area just sprayed with solution (drystroke). Then slowly pull deep cleanerback toward you without squeezing trig-ger (dry stroke).
7. Overlap strokes by 1 inch to help pre-vent streaking.Keep nozzle flat on floor for both forwardand reverse strokes.For heavily soiled areas, repeat steps 5-7.8. To avoid saturating carpet, do notuse more than 4 wet strokes over onearea. Always end with dry strokes.It is best to alternate wet and drystrokes as described above.For best cleaning results and to aid infaster drying of carpet, end with moredry strokes. (Continue using dry strokesuntil little water is visible passingthrough the recovery tank lid.)Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, Fig. 2-6).When finished cleaning, follow “Aftercleaning” instructions on page 8.
The stair/upholstery nozzle has a built-in brush to help provide the scrubbingaction some spots may need forremoval.The utility nozzle (some models) canbe used for carpet and upholstery invehicles.
How to attach toolDisconnect deep cleaner from electri-cal outlet.1. Place handle in upright position andremove hose from rack.All tools attach to the hose in the samemanner:2. Connect tool to hose by sliding it ontoconnector until the tab (C) locks itsecurely.Using your thumb, push forward andup on the latch (D) to remove tool asshown.
Read “Before you begin cleaning”Instructions on page 8. 1. Place handle in upright position.Agitator brushes will not rotate whilehandle Is in upright position. 2. Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2-10 to 2-16.3. Attach tool to end of hose. 4. Hose length may require thatmachine be placed at the top of thestairs to clean upper half of stairwayand at bottom of stairs to clean lowerhalf. To prevent machine from falling, useextra caution when cleaning on stairs. Do not place deep cleaner on stairs. Do not point tools toward people orpets. 5. Dry hands and plug deep cleanerinto a properly grounded outlet. 6. Turn deep cleaner ON.
C
D
Cleaning carpetedstairs
3-4 C
To clean nozzleIf lint or other debris becomes lodged innozzle, do not attempt to remove nozzle cover.Pour one to two cups of clear water on anon-carpeted floor. Do not pour wateronto a wood floor.Pick up water with your ‘SteamVac’ deepcleaner. Repeat as necessary untildebris is flushed out of nozzle.
10
7. Pre-spray the carpeted stair by hold-ing the tool about one inch above thecarpet and push it forward while press-ing the trigger (equals one wet stroke). 8. Position tool against the riser and slightlyp ress it into carpet pile. Press the triggerand pull the tool s l o w l y over the carpet( s e c o n d wet stroke). Release trigger at endof stroke.
9. Lift tool, and position it against riser.Pull tool slowly over carpet withoutpressing trigger (dry stroke). It is best to alternate wet and drystrokes as described above. End withmore dry strokes to aid in faster dryingof carpet. 10. Overlap strokes by 1/2 inch to helpprevent streaking. To avoid saturating carpet, do not usemore than 4 wet strokes over any onearea. Always end with dry strokes.
If additional cleaning is necessary, waituntil the carpet is completely dry beforeusing the tool again. 11. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see“Automatic shut-off”, Fig. 2-6).Read “Before you begin cleaning”Instructions on page 8.
6. Gently press the tool (A) or (B) ontothe fabric. Press the trigger and slowlypull the nozzle over the fabric.7. Overlap strokes by 1/2 inch to helpprevent streaking.Make additional strokes without pressingthe trigger to remove more moisture.8. To clean in corners or creases, lift thetool one-half inch from the fabric andpress the solution trigger.9. Vacuum up the solution with the toolwithout pressing the trigger.
10. For heavily soiled areas, it may benecessary to repeat the cleaningprocess. Make crisscrossing strokes tothe original pattern; overlap each pass.Make no more than 2 passes with thesolution over any one area to preventover-wetting and damage to fabric.If additional cleaning is necessary, waituntil the upholstery is completely drybefore using the tool again.11. Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, Fig. 2-6).When finished cleaning, follow “Aftercleaning” instructions on page 8.
3-5
Be sure to check the cleaning code onyour upholstery. Use your HOOVER‘SteamVac’ deep cleaner only onupholstery marked “W” or “W/S”. 1. Place handle in upright position.Agitator brushes will not rotate whilehandle Is In upright position.2. Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions for Figs. 2-10 to 2-16. 3. Attach tool to end of hose.Do not point tools toward people orpets.4. Dry hands and plug deep cleaner intoa properly grounded outlet.5. Turn deep cleaner on.
3-6
Cleaning upholstery 3-7 3-8
11
LubricationThe motor Is equipped with bearingswhich contain sufficient lubrication forthe life of the motor. The addition oflubricant could cause damage. Do notadd lubricant to motor bearings.
ServiceTo obtain approved HOOVER serviceand genuine HOOVER parts, locate thenearest Hoover Factory Service Centeror Authorized Hoover WarrantyService Dealer (Depot) by:
• checking the Yellow Pages under Vacuum Cleaners - Household” OR
• checking the list of Factory Service Centers provided with this cleaner OR -
• calling 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only)OR-
• checking the Service section of TheHoover Company on-line at www.hoover.com
Please do not send your cleaner to TheHoover Company in North Canton forservice, this will only result in delay.If further assistance Is needed, contactThe Hoover Company ConsumerResponse Center, North Canton, Ohio44720 Phone: 1-330-499-9499.
Always identify your cleaner by the com-plete model number when requestinginformation or ordering parts. (Themodel number appears on the bottom ofthe cleaner.)
4. MaintenanceR e m o v a b l eb ru s h e sYour deep cleaner is equipped withremovable brushes for easy cleaning.
To remove bru s h e sDisconnect cleaner from electricaloutlet.To prevent possible leaking, removeclean solution tank and recovery tank.Set tanks aside.
4-1 4-2B
B
BA
Press handle release pedal to lower han-dle. Turn cleaner over so bottom is fac-ing up.
Grasp inner portion of brush (A) and pullbrush assembly out slightly to reveallatches (B).
4-3
B
BB
B
4-4 4-5C
CD
D
E F
Press all four latches (B) and pull brushblock out. The brushes can be cleanedunder running water.
Press brush assembly firmly to snap intoplace.To replace bru s h e s
Align posts (C) on both ends of brushassembly with slots (D) in cleaner hous-ing.Make sure that square post (E) alsoaligns with square hole (F). Turn brush-es slightly until post fits easily into hole.
S t o r a g eBefore storing:
• Empty solution tank and rinse thoroughly with clean water.
• Replace empty solution tank and turn deep cleaner ON. Squeeze trigger and push deep cleaner for-ward and back several times to
expel any solution remaining in the deep cleaner’s system. (Do not use
deep cleaner on wood floors.)• Empty recovery tank and rinse
thoroughly with clean water.Allow brushes and underside of deepcleaner to air dry thoroughly beforestoring deep cleaner on a carpeted orwood surface.Do not store deep cleaner with a fullsolution tank In place.
• Blown fuse/tripped breaker• Replace fuse/reset breaker
5. If you have aproblem
Problem: Machine won’t run
Problem: Low suction
Problem: Clean solution won’t
dispense
Problem: Brushes/brush indicatorwon’t rotate during floor cleaning
Possible causePossible solution
• Recovery tank full/automatic shut off engaged
• Remove and empty recovery tank
• Hose end not secured • Ensure that hose end is pushed
completely down in holder (Fig. 1-12)
• Blockage In tool on end of hose • Remove tool and clear blockage
• Recovery tank lid not on correctly
• Make sure lid is on securely
Possible causePossible solution• Solution tank not firmly in place • Make sure tank is securely locked in
position • Solution tank empty• Refill tank according to instructions for
surface being cleaned• Recovery tank lid not on
correctly • Make sure lid is firmly in place
Possible causePossible solution• Indicator screen dirty • Remove clear cover over indicator
and clean screen; replace cover • Speed selector on OFF • Move speed selector to Low or Hi
If a minor problem occurs, it usually canbe solved quite easily when the cause isfound by using the check list below.
Full Six MonthWarranty
(Domestic Use)
Your re m a n u f a c t u red HOOVER® appli-ance is warranted in normal householduse, in accordance with the Owner’sManual, against original defects in mate-rial and workmanship for a period of sixmonths from date of purchase. This war-ranty provides, at no cost to you, alllabor and parts to place this appliance inc o rrect operating condition during thew a rranted period. This warranty applieswhen the appliance is purchased in theUnited States including its territories andpossessions, or from a U. S. MilitaryExchange. Appliances purchased else-w h e re are covered by a limited six monthw a rranty which covers the cost of part so n l y. This warranty does not apply if theappliance is used in a commercial orrental application.
Warranty service can only be obtainedby presenting the appliance to one ofthe following Authorized WarrantyService outlets. Proof of purchase will berequired before service is rendered.
1. Hoover Factory Service Centers.
2. Hoover Authorized Warranty Service Dealers (Depots).
For an automated referral of autho-rized service outlets in the U.S.A.,phone 1-800-944-9200 ORvisit The Hoover Company on-line atwww.hoover.com
This warranty does not cover pick updelivery, or house calls; however, if youmail your appliance to a Hoover FactoryService Center for warranty service,transportation will be paid one way.
While this warranty gives you specificlegal rights, you may also have otherrights which vary from state to state.
If further assistance is needed, or ifthere are questions concerning this war-ranty or the availability of warranty ser-vice outlets, write or phone theConsumer Response Center, TheHoover Company, 101 East Maple St.,North Canton, Ohio 44720. Phone 1-330-499-9499.
Possible causePossible solution
• Not firmly plugged in• Plug unit in firmly
• No voltage In wall plug• Check fuse or breaker
HOOVER and are registered trademarks
3-02 F5841-/42-9RM Litho USA 56518-145
