Solutions for Oil & Gas and Petrochemical Processing P3M2H ™ 2-VALVE PIPE x PIPE MANIFOLD 3/16” Bore 2-Valve Pipe x Pipe Manifold The 2-valve block and bleed manifold is an efficient and economical choice for static pressure measurement due to its built-in vent/calibration port. The pipe-by-pipe design features a body manufactured from extruded solid bar, robust stems and bonnets pinned for safety. Parker’s unique design assures a bubble tight seal. The manifold is offered in a variety of special tips, materials and configurations that meet most application requirements. Standard Features Benefits 2-VALVE MANIFOLD Hydrotested at 150% of rated pressure (shell test). Nitrogen gas tested to 2000 psi. Seat tightness (zero leakage) verified to 110% of rated pressure. Nitrogen gas tested to 2000 psi. Packing below stem threads Metal-body-to bonnet seals are in compression, not tension Stem threads are rolled, not cut 8 RMS stem finish V-Style Teflon™ packing Pressure component materials sourced from the US, Canada or Europe Complies with ASME B31.1 & B31.3 shell testing procedures as standard. Ensures structural integrity of valve. Complies with ASME B31.1 & B31.3 seat testing procedures as standard. Ensures zero leakage at seats for proper calibration. Prevents corrosion of critical stem threads Mitigates risk of stress cracking Higher quality stem for longer service life Extended packing life 30-40% less operational torque and less frequent packing adjustments than traditional Teflon™ packed valves Reliable material traceability. MTR’s provided with every order for pressure containing components.
Transcript
Solutions for Oil & Gas and Petrochemical Processing
P3M2H™ 2-VALVE PIPE x PIPE MANIFOLD
3/16” Bore 2-Valve Pipe x Pipe ManifoldThe 2-valve block and bleed manifold is an efficient andeconomical choice for static pressure measurement due to its built-in vent/calibration port. The pipe-by-pipe design features a body manufactured from extruded solid bar, robust stems and bonnets pinned for safety. Parker’s unique design assures a bubble tight seal. The manifold is offered in a variety of special tips, materials and configurations that meet most application requirements.
Standard Features Benefits
2-VALVE MANIFOLD
economical choice for static pressure measurement due to its
features a body manufactured from extruded solid bar, robust
design assures a bubble tight seal. The manifold is offered in a variety of special tips, materials and configurations that
Hydrotested at 150% of rated pressure (shell test). Nitrogen gas tested to 2000 psi.
Seat tightness (zero leakage) verified to 110% of rated pressure. Nitrogen gas tested to 2000 psi.
Packing below stem threads
Metal-body-to bonnet seals are incompression, not tension
Stem threads are rolled, not cut
8 RMS stem finish
V-Style Teflon™ packing
Pressure component materials sourced from the US, Canada or Europe
Complies with ASME B31.1 & B31.3 shell testing procedures as standard. Ensures structural integrity of valve.
Complies with ASME B31.1 & B31.3 seat testingprocedures as standard. Ensures zero leakage at seats for proper calibration.
Prevents corrosion of critical stem threads
Mitigates risk of stress cracking
Higher quality stem for longer service life
Extended packing life
30-40% less operational torque and less frequent packing adjustments than traditional Teflon™ packed valves
Reliable material traceability. MTR’s provided with every order for pressure containing components.
2.50”
4.53”(Open)
Specifications:Type: P3M2H, Pipe x Pipe, Globe PatternRating: Up to 6000 psi @ 100ºF (41370 kPa @ 38°C)Stem: Needle tip or Ball tipPacking: Viton™ O-ring, Teflon™ or Grafoil™Seat: IntegralHandle: RemovableBore Size: 3/16” (Primary), 1/8” (Bleed)Inlet Connections: 1/2” FNPTOutlet Connections: 1/2”FNPT Bleed Port: 1/2”FNPTBonnet Lock: Pin or PlateBody Stock: 2.5” x 2.5” x 1.25”Weight: 2.24 - 2.31 lbsMounting: 2 mounting holes included on manifold for vertical mountingSpecial Service: O2 or CL cleaning available* *Other specifications or services may be available.
Pipe x Pipe Configuration
P3M2H™ 2-Valve Pipe x Pipe ManifoldTechnical Specifications
4.17”
6.15”(Open)
Specifications:Type: P3M2H, Pipe x Futbol, Globe PatternRating: Up to 6000 psi @ 100ºF (41370 kPa @ 38°C)Stem: Needle tip or Ball tipPacking: Viton™ O-ring, Teflon™ or Grafoil™Seat: IntegralHandle: RemovableBore Size: 3/16”(Primary), 1/8” (Bleed)Inlet Connections: 1/2” FNPTOutlet Connections: 1/2” FNPT Bleed Port: 1/4”FNPTBonnet Lock: Pin or PlateBody Stock: 3.750” x 2.5” x 1.25”Weight: 4.56 - 4.71 lbsMounting: Integral 2-inch “U“ bolt for pipe stand mounting includedSpecial Service: O2 or CL cleaning available* *Other specifications or services may be available.
Pipe x Futbol Configuration
3.25”(Open)
3.65”(Open)
2
INST
PROC
BLOCK
BLEED
BLO
CK
BLE
ED
BLOCK
BLE
ED
BLOCK
Bleed Bonnet Removed
OptionalInlet
Two 1/4” UNF x 1/2” depth mounting holes on 1.0” spacing
Vent
Vent
2.875”
Two Ø.41” mounting holes
P3M2H™ 2-Valve Pipe x Pipe ManifoldBonnet, Stem and Seat Characteristics
3
Note: Body material specifications based on ASME B16.34 - 2009. Packing material ratings based on manufacturer’s specifications. Approximations only. Parker does not represent these values as finite. They are provided only as representative values.
REMOVABLE HANDLE
DUST COVER
BONNET (LOCK PIN NOT SHOWN)
DUAL O-RING SEAL
BACK SEAT
NEEDLE TIP STEM(STANDARD)
3/16” Bore Ball Tip (Optional)
Stem and Seat Configurations
3/16” Bore Needle Tip (Standard)
REMOVABLE HANDLE
DUST COVER
LOCKING ADJUSTER
BONNET (LOCK PIN NOT SHOWN)
“V” TYPE TEFLON™ (3 Pcs) or GRAFOIL™ PACKING
BACK SEAT
BALL TIP STEM(OPTIONAL)
O-Ring Bonnet Assembly
Teflon™ or Grafoil™ Bonnet Assembly
Standard Materials
Valve Body Bonnet Stem Ball Packing
CS ASTM A108CS
ASTM A108CS
ASTM A582 303SS
SEE OPTIONCODESON PAGE 4
Dual Viton™ O-ring with Teflon™ backupring
SC ASTM A105CS
ASTM A182 316SS
ASTM A182 316SS
316SS ASTM A182 316SS
ASTM A182 316SS
ASTM A182 316SS
Standard Materials
Valve Body Bonnet Stem Ball Packing
CS ASTM A108CS
ASTM A108CS
ASTM A582 303SS
SEE OPTION CODESON PAGE 4
Teflon™ and Grafoil™
SC ASTM A105CS
ASTM A182 316SS
ASTM A182 316SS
316SS ASTM A182 316SS
ASTM A182 316SS
ASTM A182 316SS
Mini Ball Tip(Optional)
Mini Needle Tip(Standard)
NOTE: Low torque Grafoil™ available (G4 Packing Code)
Parker Orifice Size
Type Inlet Size
Inlet Type Outlet Size
Outlet Type Material Packing Seat Stem Tip
P 3=3/16” M2H 8=1/2” F=FNPT 8=1/2” F=FNPT SS=ASTM A182 316/316L
A=Aflas™ Integral (leave blank)
Needle Tip Standard (leave blank)
FB=Futbol SC=ASTM A105 CS*
V=Viton™ (FKM)
B=316SS Ball Tip
CS=ASTM A108 CS*
T=Teflon™ (PTFE)
BC=Ceramic Ball Tip
C5=ASTM A350 LF2
G=Grafoil™ BM=Monel™ Ball Tip
N4=Monel™ 400
G4=LowTorqueGrafoil™
N6=Inconel™ 625N8=Inconel™ 825N2=Hastelloy™ C276
EXAMPLE: P3M2H8FFBSSTB = 3/16” Orifice, 2-Valve Manifold, 1/2” FNPT Inlet, Futbol Outlet, 316 SS Body, Teflon™ Packing, Integral Seat, 316 SS Ball Tip StemP 3 M2H 8 F FB SS T B* For code applications, A105 CS must be selected for CS valves. Code grade bolts must be specified for code applications.** Used for pipe x pipe manifolds only (See Option Codes)Note: Standard Bolting Options, CS - carbon steel, Gr.8, zinc plated bolts; SS - stainless steel, 18.8 (304SS) bolts.
Parker provides the information herein in good faith but makes no representation as to its comprehensiveness or accuracy. The information contained herein is intended only as a guide to its products and services. Individuals using information must exercise independent judgment in evaluating product selection and determining product appropriateness for their particular purpose and system requirements. PARKER MAKES NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED,INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE INFORMATION SET FORTH HEREIN OR THE PRODUCT(S) TO WHICH THE INFORMATION REFERS. ACCORDINGLY, PARKER WILL NOT BE RESPONSIBLE FOR DAMAGES (OF ANY KIND OR NATURE, INCLUDING INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES) RESULTING FROM THE USE OF OR RELIANCE UPON THIS INFORMATION. Patents and Patents Pending in the U.S. and foreign countries. Parker reserves the right to change product designs and specifications without notice.
PEEK is a registered TM of Whitford Wordwide Company and Whitford B.V. KEL-F is a registered TM of M.W. Kellogg Company. GRAFOIL is a registered TM of High Temperature Materials Inc. and Graftech INC. Corporation. AFLAS is a registered TM of Asahi Glass Co. Ltd. Corporation Japan. MONEL and INCONEL are registered TMs of Huntington Alloys Corporation. HASTELLOY is a registered TM of Haynes International, Inc.
