HOL.502607QCS Orange DS 16 GritDesigned for exposing large aggregate and removing or prepping for thin mil coatings
HOL.5026075QC Orange DS 25 GritDesigned for exposing large aggregate or removing or prepping for 10 mil coatings
HOL.502608QCS Orange DS 40 GritDesigned to hone concrete for diamond polishing or thin mil coating preparation
HOL.502609QCS Orange DS 80 Grit Designed to follow 40 Grit, often used as a first step on new concrete, ideal prep for acid staining
HOL.502610QCS Orange DS 150 GritDesigned to follow the 80 Grit in polishing applications to leave a smooth, even profile
HOL.502611QCS Orange DS 300 GritRemoves 150 Grit scratch pattern and leaves an ideal profile prior to going to a resin bond diamond
ITEM DESCRIPTION IDEAL USE
HOL.502808QCS Orange Long Life 30/40 Grit
Designed for smoothing out broom finished and heavy shot blasted concrete surfaces
HOL.502809QCS Orange Long Life 60/80 Grit
Designed for smoothing rained on slabs,sight shot blasted concrete and for removing thin coatings
HOL.502810QCS Orange Long Life 120/150 Grit
Designed for smoothing rained on slabs and extremely soft concrete
were engineered for the most abrasive grinding applications, including rained on concrete, spalled concrete, broom finished concrete, and shot blasted floors.
The Orange Series Long Life Diamonds
OR
AN
GE
SE
RIE
S
EXTREMELY HARD VERY HARD HARD MEDIUM SOFT VERY SOFT
Very hard bond used to grind very soft concrete floors.
HOL.502832Y3” QuikCut Hybrid Diamond Yellow Series, Medium Grit
For quick, aggressive cutting on new concrete. (For hard concrete)
HOL.502832B 3” QuikCut Hybrid Diamond, Black Series, Medium Grit
For quick, aggressive cutting on new concrete. (For soft to medium concrete)
HOL.502838Y 2” QuikCut Hybrid Diamond, Yellow Series, Medium Grit
For quick, aggressive cutting on new concrete. (For hard concrete)
HOL.502838B 2” QuikCut Hybrid Diamond, Black Series, Medium Grit
For quick, aggressive cutting on new concrete. (For soft to medium concrete)
QuikCut hybrids are the perfect transition diamond as you move from metal to resin bond. In some applications, these diamonds can be used as the initial cut, thus eliminating the use of a metal bond.
Ideal for removing medium to thick mil coatings. 10 PCD segments versus 6, providing maximum removal.
HOL.201014(A) HOL.201015(B)
Silver PCD Diamond Plate with Wear Bar, 270mm
*Silver PCD Diamond Plate with Wear Bar, 270mm <opposite>
Removes thin to medium mil coatings without damaging the concrete surface. Diamond wear bar controls the depth of the cut while leaving a smooth profile.
NB.13.118 Screw, Flat Head Socket CapFor use with non-plate style PCD tooling. Requires three per segment.
SAS.20016 Mounting head assembly, 5K bush hammer Fits PDG 5000
SAS.20016 Roller, 5K Bush Hammer Fits PDG 5000
SAS.20007 Bearing, 5k Bush Hammer Fits PDG 5000
SAS.00178 240mm Bush Hammer PlateStandard profile Fits Diamatic
A bush hammer is a tungsten tip tool used to remove coatings or texture concrete. The 45/100 pins leave an excellent profile for the bonding of coatings and overlays. This tool is also effective at creating a non-stick profile suitable for both inside and outside environments.
SC30.500502 3” Metal Flex Aqua 30 Grit Aggressive cutting without gouging
SC30.500503 3” Metal Flex Grey 50 Grit Ideal for removing sealers and as a first cut on new concrete
SC30.500504 3” Metal Flex Black 100 Grit Removes scratches left by 50 Grit Metal Flex Pads
The Metal Flex diamonds are ideal for removing mastics and sealers, and to profile edges without gouging the floor. Each individual diamond segment is 1/8” and won’t bind or close up.
ITEM DESCRIPTION IDEAL USE
SC30.500240 3” Polishing Resin Bond Diamond Grey 50 Grit Removal of scratches left by metal bonds
SC30.500241 3” Polishing Resin Bond Diamond Black 100 Grit Used as the first step in polishing
SC30.500242 3” Polishing Resin Bond Diamond Blue 200 Grit Used for removal of 100 Grit scratches
SC30.500243 3” Polishing Resin Bond Diamond Red 400 Grit Typically used as the last step before dye and densifier are applied
SC30.500244 3” Polishing Resin Bond Diamond White 800 Grit Provides a high shine, often the last step in polishing of retail stores
SC30.500245 3” Polishing Resin Bond Diamond Yellow 1500 Grit Provides a very high shine
SC30.500246 3” Polishing Resin Bond Diamond Green 3000 Grit Provides a very high shine
These polishing diamonds work great under smaller, lighter weight machines, and are a great alternative for concrete polishing. Good on various self-leveling compounds.
SC50.500502 5” Metal Flex Aqua 30 Grit Aggressive cutting without gouging
SC50.500503 5” Metal Flex Grey 50 Grit Ideal for removing sealers and as a first cut on new concrete
SC50.500504 5” Metal Flex Black 100 Grit Removes scratches left by 50 Grit Metal Flex Pads
The Metal Flex Pads are ideal for removing mastics and to profile edges without gouging the floor. Each individual diamond segment is 1/8” and won’t bind or close up providing an extended life. These diamonds are for use on the SASE SC50 and other industry 5” hand grinders.
ITEM DESCRIPTION IDEAL USE
SC50.500240 5” Polishing Resin Bond Diamond Grey 50 Grit Removal of scratches left by metal bonds
SC50.500241 5” Polishing Resin Bond Diamond Black 100 Grit Used as the first step in polishing
SC50.500242 5” Polishing Resin Bond Diamond Blue 200 Grit
Used for removal of 100 Grit scratches and as the last step before concrete dye in some applications
SC50.500243 5” Polishing Resin Bond Diamond Red 400 Grit
Typically used as the last step before dye and densifier are applied
SC50.500244 5” Polishing Resin Bond Diamond White 800 Grit
Provides a high shine, often the last step in polishing of retail stores
SC50.500245 5” Polishing Resin Bond Diamond Yellow 1500 Grit Provides a very high shine
SC50.500246 5” Polishing Resin Bond Diamond Green 3000 Grit Provides the highest shine
These diamonds are excellent for concrete polishing edge work. For use on the SASE SC50 and other industry 5” hand grinders.
Often used in place of the 100 Grit metal bond for removal of thin mil coatings and sealers
SC50.500402 5” SURE CUT Copper Polishing Diamond Black 100 Grit
Often used to reduce scratches left from 50 Grit metal bond
These copper bonded diamonds provide improved longevity and elimination of swirl marks. These diamonds are for use on the SASE SC50 and other industry 5” hand grinders.
ITEM DESCRIPTION IDEAL USE
SC50.900901 5” Rigid Backer Pad 5/8” Arbor Preferred use with 5” Metal Flex
SC50.900902 5” Flexible Backer Pad 5/8” Arbor Preferred use with 5” Resin Polishing Pad
SC60.500249 6” Metal Flex Yellow 16 Grit Very Aggressive cutting without gouging
SC60.500250 6” Metal Flex Aqua 30 Grit Aggressive cutting without gouging
SC60.500251 6” Metal Flex Grey 50 Grit Ideal for removing sealers and as a first cut on new concrete
SC60.500252 6” Metal Flex Black 100 Grit Removes scratches left by 50 Grit Metal Flex Pads
The Metal Flex Pads are ideal for removing mastics and to profile edges without gouging the floor. Each individual diamond segment is 1/8” and won’t bind or close up providing an extended life.
6" METAL FLEX DIAMONDS
5" HYBRID EDGE PAD
6" HYBRID EDGE PRO PAD
ITEM DESCRIPTION IDEAL USE
SC.50500600 5" Hybrid Edge Pad For use on SC50
ITEM DESCRIPTION IDEAL USE
SC.60500260 6” Hybrid edge pro pad 100 Grit SASE Edge Pro 180
Using this new high quality SASE hybrid edge tooling will eliminate steps in the edge polishing process.
Using this new high quality SASE hybrid edge tooling will eliminate steps in the edge polishing process.
ITEM DESCRIPTION IDEAL USE
SAS.04015 5" Rapid strip disc, coarse wheel used to sand structural polyurethane off of polished concrete For use on SC50
For stock removal of concrete and mastics, rubbers, epoxies, and other coatings
SC50.900701M 5” QUIKCUT Edge WheelMedium Blue
For stock removal of concrete and mastics, rubbers, epoxies, and other coatings
SC50.900700F 5” QUIKCUT Edge WheelFine Yellow Aggressive removal of thin to medium coatings
Our advanced technology 3 step edge wheel polishing system with outstanding finishes. This system will reduce your time by up to 50% compared with conventional methods.
ITEM DESCRIPTION IDEAL USE
SC50.900608 5” 18 Segment Cup Wheel Threaded
For stock removal of concrete and mastics, rubbers, epoxies, and other coatings
SC50.900609 5” T-Segment Cup Wheel Threaded
For stock removal of concrete and mastics, rubbers, epoxies, and other coatings
SC50.900610 5” Arrow Segment Cup Wheel Threaded Aggressive removal of thin to medium coatings
Ideal for light surface prep or for polished concrete edge work to expose minimal aggregate, while leaving a smooth profile and blending edges
SC50.900811 5” Hybrid Resin Filled Medium Threaded
Ideal for light surface prep or for polished concrete edge work, leaving a smooth profile and blending edges
SC50.900812 5” Hybrid Resin Filled Fine Threaded
Ideal for polished concrete edge work, leaving a smooth profile and blending edges
SC50.900711 5” Diamond Cluster Cup Wheel Medium Grit
Fast aggressive removal of paints, epoxies and glue
The 5” cup wheels are excellent for coatings removal and aggregate exposure of concrete surfaces, and are used on the SASE SC50 and all other industry 5” hand grinders.
SC70.900604 7” 18 Segment 9 Long, 9 Short Non-Threaded Thin mil removal
SC70.90016 7” Diamond Cluster Cup Wheel Medium Grit Fast aggressive removal of paints, glue and epoxies
The 7” cup wheels are excellent for coatings removal and aggregate exposure of concrete surfaces. They are used on the SASE SC70 and other industry 7” hand grinders.
Our most advanced technology, a three step edge wheel polishing system with outstanding finishes. Reduces your time by up to 50% compared with conventional methods.
SSP.27.40100 27” TRIFECTA PAD 100 Grit Used for burnishing and restoration under 27” burnishers
SSP.27.40400 27” TRIFECTA PAD 400 Grit Used for burnishing and restoration under 27” burnishers
SSP.27.40800 27” TRIFECTA PAD 800 Grit Used for burnishing and restoration under 27” burnishers
SSP.27.41500 27” TRIFECTA PAD 1500 Grit Used for burnishing and restoration under 27” burnishers
SSP.27.43000 27” TRIFECTA PAD 3000 Grit Used for burnishing and restoration under 27” burnishers
ITEM DESCRIPTION IDEAL USE
SSP.24.30100 24” TRIFECTA PAD 100 Grit Used for burnishing and restoration under 24” burnishers
SSP.24.30400 24” TRIFECTA PAD 400 Grit Used for burnishing and restoration under 24” burnishers
SSP.24.30800 24” TRIFECTA PAD 800 Grit Used for burnishing and restoration under 24” burnishers
SSP.24.31500 24” TRIFECTA PAD 1500 Grit Used for burnishing and restoration under 24” burnishers
SSP.24.33000 24” TRIFECTA PAD 3000 Grit Used for burnishing and restoration under 24” burnishers
These pads will mount to a high speed burnisher to restore shine or burnish in guard. Use our TRIFECTA pads for a full rejuvenation of a polished concrete floor & remove imperfections left by the polishing process.
ITEM DESCRIPTION IDEAL USE
SSP.17.10100 17” TRIFECTA PAD 100 Grit Used for burnishing and restoration under 17” burnishers
SSP.17.10400 17” TRIFECTA PAD 400 Grit Used for burnishing and restoration under 17” burnishers
SSP.17.10800 17” TRIFECTA PAD 800 Grit Used for burnishing and restoration under 17” burnishers
SSP.17.11500 17” TRIFECTA PAD 1500 Grit Used for burnishing and restoration under 17” burnishers
SSP.17.13000 17” TRIFECTA PAD 3000 Grit Used for burnishing and restoration under 17” burnishers
ITEM DESCRIPTION IDEAL USE
SSP.20.20100 20” TRIFECTA PAD 100 Grit Used for burnishing and restoration under 20” burnishers
SSP.20.20400 20” TRIFECTA PAD 400 Grit Used for burnishing and restoration under 20” burnishers
SSP.20.20800 20” TRIFECTA PAD 800 Grit Used for burnishing and restoration under 20” burnishers
SSP.20.21500 20” TRIFECTA PAD 1500 Grit Used for burnishing and restoration under 20” burnishers
SSP.20.23000 20” TRIFECTA PAD 3000 Grit Used for burnishing and restoration under 20” burnishers
