English - �
The Supplied Accessoris
Owner’s Instructions Remote Control/AAA Batteries (2ea)
Power Cord Cloth-Clean
Holder-Wire Cable Screw (4ea) Cover-Bottom Holder-Ring (4ea)
Ferrite Core for Power Cord
Installing Batteries in the Remote Control
PDP TVQUICK SETUP GUIDE
BN68-02282A.indd 1 2009-04-09 오후 3:35:21
English - �
Installing the Stand
Step �. Attach your PDP TV to the stand.Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury.Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen. Always store the TV upright.
NN
Step �. Using the 4 screws for securing the stand base and the monitor, firmly attach the monitor to the stand base. (The exterior of the set may be different than the picture.)
Step 3. In case of installing your TV on the wall, close the cover 1 on the stand-base connection part using two screws for hiding.
Assembling the CablesEnclose the cables in the Holder-Wire Cable so that the cables are not visible through the transparent stand.
Using the remote control buttons
Back
Front Back
Front
Step � Step � Step 3
RETURN ButtonReturns to the previous menu
EXIT ButtonExit the on-screen menu
MENU ButtonDisplays the favourites channel list.
ENTERE / Direction ButtonMove the cursor and select an item.
Select the currently selected item. Confirm the setting.
BN68-02282A.indd 2 2009-04-09 오후 3:35:24
English - 3
Plug & PlayWhen the TV is initially powered on, basic settings proceed automatically and subsequently.If you want to reset this feature, press the MENU button to display menu.You can set the Plug & Play by selecting Setup → Plug & Play.
On the screen, you can set as follows.The each step may vary depending on the Antenna source.N
Plug & Play
Select the OSD Language.
E Enter
Menu Language : English ►
Step �
Plug & PlaySelect the Antenna source to memorise.
Air
Cable Start
U Move E Enter Skip
Start
Step 4
Step 3
Plug & Play
Select Country.
E Enter
Country : United Kingdom ►
Step �
Plug & Play
Select ‘Home Use’ when installing this TV in your home.
Store Demo Home USE
L Move E Enter
Step 9
Enjoy your TV.
OK
Step 5
Plug & PlaySelect the Channel source to memorise.
Digital & Analogue
Digital
Analogue
Start
U Move E Enter Skip
Start
Start
Step 6
Plug & PlayAuto Program in Progress.
Stop
3%
Channel 10Digital Channels : 0 Analogue Channels : 0
Step 8
Plug & Play
Set the Clock Mode.
E Enter Skip
Clock Mode : Auto ►
E Enter Skip
Step 7
Plug & PlayHow to get the best performance from your new HDTV.Step 1. �Connect the HD box to the TV using the Component video (Red,Green,
Blue) and audio (Red, White) cables or HDMI Cable. ▼�HD box� ▼�TV rear view
E Enter
Step 2. �Press the Source button on the Remote to select HDMI or Component Input.
Depending on your location, HD programming may also be viewed using an RF antenna.For more details, please refer to HD Connections in the Owner Manual.
HDMI Cable
Component Cable
BN68-02282A.indd 3 2009-04-09 오후 3:35:26
English - 4
Connecting a AV device
WY R
WY R R
WR
WR
R
G
G
B
B
HD connection
DVD / Blu-Ray player / Cable Box / Satellite receiver (STB)
Using a DVI Cable
AUDIO OUTDVI OUT
HD connection
DVD / Blu-Ray player / HD Cable Box / HD Satellite receiver (STB)
Using an HDMI Cable
HDMI OUT
Audio/Video connection
VCR
Using an Audio/Video Cable
AUDIO OUTVIDEO OUT
Component connection
DVD / Blu-Ray player / Cable Box / Satellite receiver
Using a Component Cable
AUDIO OUT COMPONENT OUT
HDMI/DVI
PC/COMPONENT
EXT/VIDEO
Best
Norm
al
VCR / DVD
Using a Scart Cable
EXT
BN68-02282A-01BN68-02282A
BN68-02282A.indd 4 2009-04-09 오후 3:35:28