Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-1
250 Series Casement
Performance
Glazing Performance
Grille Profiles and Patterns
Size Tables
Design Data
Detailed Product Description
Cross Sections
The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are subject to change without notice. Consult your local Pella representative for up-to-date product information.
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-2
250 Series Casement
Rev. 01/24/2019
Sound Transmission Class and Outdoor-Indoor Transmission Class
Frame Size Tested 3
Glazing SystemSTC
RatingOITC
RatingOverall Glazing Thickness
Exterior Glass Thickness
Interior Glass Thickness
Third Pane Thickness
Casement - Dual pane insulating Glass
Vent 23-1/2" x 59" 3/4" 3mm 3mm — 30 25
Vent 23-1/2" x 59" 1" 3mm 5mm — 33 27
Fixed 47-1/4" x 59" 3/4" 3mm 3mm — 28 24
Fixed 47-1/4" x 59" 1" 3mm 5mm — 30 25
Casement – triple-pane insulating glass
Vent 23-1/2" x 59" 1" 3mm 3mm 3mm 34 28
S = Standard; O = Optional
(1) Published performance data is for single unit only. See Design Data pages in this section for specific product performance class and grade values.
(2) The higher the level, the greater the product's ability to resist forced entry.
(3) ASTM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration.The presence of low-e or argon have negligible effect on sound attenuation characteristics.
Sizes
Standard Sizes S
Special Sizes Available Built on 1/8" Increments O
Frames
Nail Fin Only O
Nail Fin with J-Channel O
3-1/4" Block Pocket Install/Replacement S
Double-Wall Flush Flange O
Integral 5/8" Flange O
Performance 1
Standard Performance
Meets or Exceeds AAMA/WDMA RatingsLC-PG35
Hallmark Certified
Air Infiltration (cfm / ft2 of frame @ 1.57 psf wind pressure.) 0.10
Design Pressure 35 psf
Water Penetration Resistance 7.5 psf
Performance Upgrade
Meets or Exceeds AAMA/WDMA RatingsLC-PG50
Hallmark Certified
Air Infiltration (cfm / ft2 of frame @ 1.57 psf wind pressure.) 0.10
Design Pressure 50 psf
Water Penetration Resistance 7.5 psf
Other Performance Criteria
Forced Entry Resistance (Minimum Security Grade) 2 10
Maximum Operating Force (lbs) (Initiate Motion / Maintain Motion) 15/6
Size and Performance Data
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-3
250 Series Casement
Glazing (insulating glass)
Glazing Type
Dual-pane insulating glass S
Triple-pane insulating glass O
Insulated Glass Options / Low-E Types
Advanced Low-E S
NaturalSun Low-E O
SunDefense™ Low-E 1 O
Bronze-tinted Advanced Low-E 1 O
Additional Glazing Options
Annealed glass S
Tempered glass O
Obscure glass 2 O
Gas Fi l l / High Alt i tude
Argon S
High altitude O
High altitude with argon 1 O
Sash
Foam Insulation O
Performance Upgrade O
Interior / Exterior Color
White Interior/White Exterior S
Almond Interior/Almond Exterior O
Fossil Interior/Fossil Exterior O
White Interior/Brown Exterior O
White Interior/Fossil Exterior O
White Interior/Black Exterior O
White Interior/Brick Red Exterior O
White Interior/Hartford Green Exterior O
White Interior/Morning Sky Gray Exterior O
White Interior/Poplar White Exterior O
White Interior/Portobello Exterior O
White Interior/Tan Exterior O
S = Standard; O = Optional (1) Not available with triple-pane glazing. (2) Contact your local Pella sales representative for current offering.
Hardware
Color matched hardware S
Screens
Conventional black fiberglass screens - flat S
Grilles
Gri l les-Between-the-Glass
3/4" Contour O
5/8" Flat O
1" Contour O
Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided O
Simulated-Divided-Light Gri l les 1 (without spacer)
7/8" contour profile O
Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided O
Features and Options
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-4
250 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
VENT – Dual-Pane 3MM Glass N NC SC S 1 2 33/4" Advanced Low-E IG PEL-N-239-00002-00007 3 3 air 0.29 0.25 0.46 57
with SDL or grilles-between-the-glass PEL-N-239-00002-00008 0.29 0.23 0.42 57
3/4" Advanced Low-E IG PEL-N-239-00005-00007 3 3 argon 0.26 0.25 0.46 60 22
with SDL or grilles-between-the-glass PEL-N-239-00005-00008 0.26 0.23 0.42 60 21
3/4" NaturalSun Low-E IG PEL-N-239-00001-00007 3 3 air 0.30 0.43 0.52 56 27
with SDL or grilles-between-the-glass PEL-N-239-00001-00008 0.30 0.39 0.47 56 25
3/4" NaturalSun Low-E IG PEL-N-239-00004-00007 3 3 argon 0.27 0.43 0.52 59 31
with SDL or grilles-between-the-glass PEL-N-239-00004-00008 0.27 0.39 0.47 59 29
3/4" SunDefense™ Low-E IG PEL-N-239-00003-00007 3 3 air 0.29 0.19 0.43 57
with SDL or grilles-between-the-glass PEL-N-239-00003-00008 0.29 0.17 0.38 57
3/4" SunDefense Low-E IG PEL-N-239-00006-00007 3 3 argon 0.26 0.18 0.43 61 18
with SDL or grilles-between-the-glass PEL-N-239-00006-00008 0.26 0.17 0.38 61 17
VENT – Dual-Pane 3MM Glass – with Foam Insulation3/4" Advanced Low-E IG PEL-N-239-00040-00007 3 3 air 0.28 0.25 0.46 57 19
with SDL or grilles-between-the-glass PEL-N-239-00040-00008 0.28 0.23 0.42 57 18
3/4" Advanced Low-E IG PEL-N-239-00043-00007 3 3 argon 0.26 0.25 0.46 61 22
with SDL or grilles-between-the-glass PEL-N-239-00043-00008 0.26 0.23 0.42 61 21
3/4" NaturalSun Low-E IG PEL-N-239-00039-00007 3 3 air 0.29 0.43 0.52 56 29
with SDL or grilles-between-the-glass PEL-N-239-00039-00008 0.29 0.39 0.47 56 26
3/4" NaturalSun Low-E IG PEL-N-239-00042-00007 3 3 argon 0.26 0.43 0.52 60 32
with SDL or grilles-between-the-glass PEL-N-239-00042-00008 0.26 0.39 0.47 60 30
3/4" SunDefense™ Low-E IG PEL-N-239-00041-00007 3 3 air 0.28 0.19 0.43 57 16
with SDL or grilles-between-the-glass PEL-N-239-00041-00008 0.28 0.17 0.38 57
3/4" SunDefense Low-E IG PEL-N-239-00044-00007 3 3 argon 0.25 0.18 0.43 61 19
with SDL or grilles-between-the-glass PEL-N-239-00044-00008 0.25 0.17 0.38 61 19
VENT – Dual-Pane 3MM Glass with Tinted Glazing3/4" Bronze Advanced Low-E IG PEL-N-239-00002-00013 3 3 air 0.29 0.25 0.34 57
with SDL or grilles-between-the-glass PEL-N-239-00002-00014 0.29 0.23 0.31 57
3/4" Bronze Advanced Low-E IG PEL-N-239-00005-00013 3 3 argon 0.26 0.24 0.34 60 21
with SDL or grilles-between-the-glass PEL-N-239-00005-00014 0.26 0.22 0.31 60 20
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
Glazing Performance - Total Unit
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-5
250 Series Casement
Rev. 01/24/2019
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
Glazing Performance - Total UnitG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext
.
Mid
dle
Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
VENT – Triple-Pane 3MM Glass N NC SC S 1 2 3
1" Advanced Low-E Triple-pane IG PEL-N-239-00033-00003 3 3 3 air 0.24 0.21 0.36 64 22
with Grilles-between-the-glass PEL-N-239-00034-00002 0.24 0.19 0.32 64 21
1" Advanced Low-E Triple-pane IG PEL-N-239-00037-00003 3 3 3 argon 0.21 0.21 0.36 67 26
with Grilles-between-the-glass PEL-N-239-00038-00002 0.21 0.19 0.32 67 25
1" NaturalSun Low-E Triple-pane IG PEL-N-239-00031-00003 3 3 3 air 0.24 0.37 0.46 63 31
with Grilles-between-the-glass PEL-N-239-00032-00002 0.24 0.34 0.41 63 30
1" NaturalSun Low-E Triple-pane IG PEL-N-239-00035-00003 3 3 3 argon 0.21 0.37 0.46 67 35
with Grilles-between-the-glass PEL-N-239-00036-00002 0.21 0.34 0.41 67 33
VENT – Triple-Pane 3MM Glass with Foam Insulation
1" Advanced Low-E Triple-pane IG PEL-N-239-00071-00003 3 3 3 air 0.23 0.21 0.36 64 23
with Grilles-between-the-glass PEL-N-239-00072-00002 0.23 0.19 0.32 64 22
1" Advanced Low-E Triple-pane IG PEL-N-239-00075-00003 3 3 3 argon 0.20 0.21 0.36 68 27
with Grilles-between-the-glass PEL-N-239-00076-00002 0.20 0.19 0.32 68 26
1" NaturalSun Low-E Triple-pane IG PEL-N-239-00069-00003 3 3 3 air 0.23 0.37 0.46 64 33
with Grilles-between-the-glass PEL-N-239-00070-00002 0.24 0.34 0.41 64 30
1" NaturalSun Low-E Triple-pane IG PEL-N-239-00073-00003 3 3 3 argon 0.20 0.37 0.46 67 36
with Grilles-between-the-glass PEL-N-239-00074-00002 0.21 0.34 0.41 67 33
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-6
250 Series Casement
Rev. 01/24/2019
Gla
ss
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
FIXED – Dual-Pane 3MM Glass N NC SC S 1 2 33/4" Advanced Low-E IG PEL-N-240-00002-00001 3 3 air 0.30 0.30 0.57 57
with SDL or grilles-between-the-glass PEL-N-240-00002-00002 0.30 0.27 0.51 57
3/4" Advanced Low-E IG PEL-N-240-00005-00001 3 3 argon 0.27 0.30 0.57 61 24
with SDL or grilles-between-the-glass PEL-N-240-00005-00002 0.27 0.27 0.51 61 22
3/4" NaturalSun Low-E IG PEL-N-240-00001-00001 3 3 air 0.31 0.53 0.64 57 32
with SDL or grilles-between-the-glass PEL-N-240-00001-00002 0.31 0.47 0.57 57 28
3/4" NaturalSun Low-E IG PEL-N-240-00004-00001 3 3 argon 0.28 0.53 0.64 60 36
with SDL or grilles-between-the-glass PEL-N-240-00004-00002 0.28 0.47 0.57 60 32
3/4" SunDefense™ Low-E IG PEL-N-240-00003-00001 3 3 air 0.30 0.23 0.52 58
with SDL or grilles-between-the-glass PEL-N-240-00003-00002 0.30 0.21 0.47 58
3/4" SunDefense Low-E IG PEL-N-240-00006-00001 3 3 argon 0.26 0.22 0.52 61 20
with SDL or grilles-between-the-glass PEL-N-240-00006-00002 0.26 0.20 0.47 61 19
FIXED – Dual-Pane 5MM Glass1" Advanced Low-E IG PEL-N-240-00024-00001 5 5 air 0.30 0.30 0.56 58
with SDL or grilles-between-the-glass PEL-N-240-00024-00002 0.30 0.27 0.50 58
1" Advanced Low-E IG PEL-N-240-00028-00001 5 5 argon 0.27 0.29 0.56 62 23
with SDL or grilles-between-the-glass PEL-N-240-00028-00001 0.27 0.27 0.50 62 22
1" NaturalSun Low-E IG PEL-N-240-00023-00001 5 5 air 0.31 0.50 0.63 58 30
with SDL or grilles-between-the-glass PEL-N-240-00023-00002 0.31 0.45 0.56 58 27
1" NaturalSun Low-E IG PEL-N-240-00027-00001 5 5 argon 0.27 0.50 0.63 61 35
with SDL or grilles-between-the-glass PEL-N-240-00027-00002 0.27 0.45 0.56 61 32
1" SunDefense™ Low-E IG PEL-N-240-00026-00001 5 5 air 0.30 0.23 0.52 59
with SDL or grilles-between-the-glass PEL-N-240-00026-00002 0.30 0.21 0.46 59
1" SunDefense Low-E IG PEL-N-240-00030-00001 5 5 argon 0.26 0.22 0.52 62 20
with SDL or grilles-between-the-glass PEL-N-240-00030-00002 0.26 0.20 0.46 62 19
FIXED - Dual-Pane 3MM Glass with Tinted Glazing3/4" Bronze Advanced Low-E IG PEL-N-240-00002-00007 3 3 air 0.30 0.30 0.42 57
with SDL or grilles-between-the-glass PEL-N-240-00002-00008 0.30 0.27 0.38 57
3/4" Bronze Advanced Low-E IG PEL-N-240-00005-00007 3 3 argon 0.27 0.30 0.42 61 24
with SDL or grilles-between-the-glass PEL-N-240-00005-00008 0.27 0.27 0.38 61 22
FIXED - Dual-Pane 5MM Glass with Tinted Glazing1" Bronze Advanced Low-E IG PEL-N-240-00025-00001 5 5 air 0.30 0.27 0.36 58
with SDL or grilles-between-the-glass PEL-N-240-00025-00002 0.30 0.24 0.33 58
1" Bronze Advanced Low-E IG PEL-N-240-00029-00001 5 5 argon 0.27 0.27 0.36 62 22
with SDL or grilles-between-the-glass PEL-N-240-00029-00002 0.27 0.24 0.33 62 20
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
Glazing Performance - Total Unit
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-7
250 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext
.
Mid
.
Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
FIXED - Triple-Pane 3MM Glass with Tinted Glazing N NC SC S 1 2 31" Advanced Low-E Triple-pane IG PEL-N-240-00041-00003 3 3 3 air 0.23 0.26 0.44 67 26
with Grilles-between-the-glass PEL-N-240-00041-00004 0.23 0.23 0.40 67 24
1" Advanced Low-E Triple-pane IG PEL-N-240-00045-00003 3 3 3 argon 0.19 0.26 0.44 71 31
with Grilles-between-the-glass PEL-N-240-00045-00004 0.20 0.23 0.40 71 28
1" NaturalSun Low-E Triple-pane IG PEL-N-240-00039-00003 3 3 3 air 0.24 0.45 0.57 66 36
with Grilles-between-the-glass PEL-N-240-00039-00004 0.24 0.41 0.51 66 34
1" NaturalSun Low-E Triple-pane IG PEL-N-240-00043-00003 3 3 3 argon 0.20 0.45 0.57 70 41
with Grilles-between-the-glass PEL-N-240-00043-00004 0.20 0.41 0.51 70 39
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500. ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2015 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor SHGC = Solar Heat Gain Coefficient VLT % = Visible Light Transmission CR = Condensation Resistance ER = Canadian Energy Rating
Climate Zones
Glazing Performance - Total Unit
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-8
250 Series Casement
Grille Profiles Grilles-Between-the-Glass
Grilles
3/4"
3/4" ContourSimulated Divided Light
7/8" 1" Contour
1"
3/4" Contour
3/4"
5/8" Flat
5/8" 7/8"
Simulated-Divided-Light Grilles Without Spacer
Prairie
- Approximately 4" from edge of sash to center of bar
- Minimum actual glass is 13"
Custon - Equally Divided
- Specify number of lites.
- Grilles must be equally divided on visible glass.
- Minimum 6" x 6".
Top Row
- Standard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller.
Other Available Patterns
Grille Patterns Prairie Lite Patterns
9-Lite Prairie
Traditional Top Row Custom — Equally Divided
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-9
250 Series Casement
2-8/2-8
2-0/2-0
2-6/2-6
2-4/2-4
1-3/2-0 1-6/2-0
1-3/2-8 1-6/2-8 2-0/2-8 2-4/2-8 2-6/2-8
1-3/2-6 1-6/2-6 2-0/2-6 2-4/2-6
1-3/2-4 1-6/2-4 2-0/2-4
1-3/1-6 1-6/1-6
1-3/3-8 1-6/3-8
2-8/6-01-3/6-0 1-6/6-0 2-0/6-0 2-4/6-0 2-6/6-0 3-0/6-0
2-8/5-61-3/5-6 1-6/5-6 2-0/5-6 2-4/5-6 2-6/5-6 3-0/5-6
2-8/5-01-3/5-0 1-6/5-0 2-0/5-0 2-4/5-0 2-6/5-0 3-0/5-0
2-8/4-61-3/4-6 1-6/4-6 2-0/4-6 2-4/4-6 2-6/4-6 3-0/4-6
2-8/4-01-3/4-0 1-6/4-0 2-0/4-0 2-4/4-0 2-6/4-0 3-0/4-0
2-8/3-82-0/3-8 2-4/3-8 2-6/3-8 3-0/3-8
2-8/3-61-3/3-6 1-6/3-6 2-0/3-6 2-4/3-6 2-6/3-6 3-0/3-6
2-8/3-01-3/3-0 1-6/3-0 2-0/3-0 2-4/3-0 2-6/3-0 3-0/3-0
3' 0"35 "/ 21
2' 8"31 "/ 2129
2' 6""/ 21
2' 4"27 "/ 2123
2' 0""/ 21
716' 0
" "/ 21
"/ 21
655' 6
"595'
0" "
/ 21534'
6" "
/ 21474'
0"
(1 2
19)
(1 2
07) "
/ 21433'
8"
(1 1
18)
(1 1
05) "
/ 21413'
6"
(1 0
67)
(1 0
54) "
/ 21
3' 0
"35(9
02)
(914
) "/ 21
312' 8
"
(813
)(8
00) "
/ 21292'
6"
(762
)(7
49) "
/ 21272'
4"
(711
)(6
99) "
/ 21232'
0"
(597
)(6
10) "
/ 21171'
6"
(457
)(4
45) "
/ 21
1' 3"14
(381)(368)
"/ 21
(1 8
29)
(1 8
16)
(1 5
24)
(1 5
11)
(1 3
72)
(1 3
59)
(1 6
76)
(1 6
64)
"/ 21
(902)(914)
FrameOpening
(762)(749)
(711)(699)
(610)(597)
1' 6"17
(457)(445) (800)
(813)
TT
T
T
T
E
E
E
E
E
E
E
1E
2E
2E
2E
2E
2E
2E
2E
2E
2E
2E
2E
2E
2E
3E
3E
Not to scale.
Certain glass aspect ratios may require tempered glass.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
Size tables - Vent
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-10
250 Series Casement
6-0/2-05-0/2-04-6/2-04-0/2-02-8/2-01-3/2-0 1-6/2-0 2-0/2-0 2-4/2-0 2-6/2-0 3-0/2-0
6-0/6-05-0/6-04-6/6-04-0/6-02-8/6-01-3/6-0 1-6/6-0 2-0/6-0 2-4/6-0 2-6/6-0 3-0/6-0
6-0/5-65-0/5-64-6/5-64-0/5-62-8/5-61-3/5-6 1-6/5-6 2-0/5-6 2-4/5-6 2-6/5-6 3-0/5-6
6-0/5-05-0/5-04-6/5-04-0/5-02-8/5-01-3/5-0 1-6/5-0 2-0/5-0 2-4/5-0 2-6/5-0 3-0/5-0
6-0/4-65-0/4-64-6/4-64-0/4-62-8/4-61-3/4-6 1-6/4-6 2-0/4-6 2-4/4-6 2-6/4-6 3-0/4-6
6-0/4-05-0/4-04-6/4-04-0/4-02-8/4-01-3/4-0 1-6/4-0 2-0/4-0 2-4/4-0 2-6/4-0 3-0/4-0
6-0/3-85-0/3-84-6/3-84-0/3-82-8/3-81-3/3-8 1-6/3-8 2-0/3-8 2-4/3-8 2-6/3-8 3-0/3-8
6-0/3-65-0/3-64-6/3-64-0/3-62-8/3-61-3/3-6 1-6/3-6 2-0/3-6 2-4/3-6 2-6/3-6 3-0/3-6
6-0/3-05-0/3-04-6/3-04-0/3-02-8/3-01-3/3-0 1-6/3-0 2-0/3-0 2-4/3-0 2-6/3-0 3-0/3-0
6-0/2-85-0/2-84-6/2-84-0/2-82-8/2-81-3/2-8 1-6/2-8 2-0/2-8 2-4/2-8 2-6/2-8 3-0/2-8
6-0/2-65-0/2-64-6/2-64-0/2-62-8/2-61-3/2-6 1-6/2-6 2-0/2-6 2-4/2-6 2-6/2-6 3-0/2-6
6-0/2-45-0/2-44-6/2-44-0/2-42-8/2-41-3/2-4 1-6/2-4 2-0/2-4 2-4/2-4 2-6/2-4 3-0/2-4
6-0/1-3
6-0/1-6
5-0/1-3
5-0/1-6
4-6/1-3
4-6/1-6
4-0/1-3
4-0/1-6
2-8/1-3
2-8/1-6
1-6/1-3 2-0/1-3 2-4/1-3 2-6/1-3 3-0/1-31-3/1-3
1-3/1-6 1-6/1-6 2-0/1-6 2-4/1-6 2-6/1-6 3-0/1-6
(368)
14
(381)
1' 3""/ 21
716' 0
"
(1 8
29)
(1 8
16) "
/ 21595'
0"
(1 5
24)
(1 5
11) "
/ 21474'
0"
(1 2
19)
(1 2
07) "
/ 21534'
6"
(1 3
72)
(1 3
59) "
/ 21"
/ 21655'
6"
(1 6
76)
(1 6
64)
6' 0""/ 2171
(1 829)(1 816)
"/ 21"/ 21
1' 6"17
(457)(445)
"/ 21
433' 8
"
(1 1
18)
(1 1
05)
413' 6
"
(1 0
67)
(1 0
54)
3' 0
"35(9
02)
(914
)
272' 4
"
"/ 21
(1 359)(1 372)
4' 6"53
5' 0""/ 2159
(1 524)(1 511)
4' 0""/ 2147"/ 21"/ 21"/ 21"/ 21 "/ 21
(902)(914)
3' 0"
(368
)
14(381
)
1' 3
"
FrameOpening
292' 6
"
(762
)(7
49)
312' 8
"
(813
)(8
00)
232' 0
"
(711
)(6
99)
(597
)(6
10)
171' 6
"
(457
)(4
45)
292' 6"
(762)(749)
232' 4"
(711)(699)
272' 0"
(610)(597) (800)
(813)
2' 8"31 35
(1 219)(1 207)
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21
"/ 21 "/ 21"/ 21"/ 21"/ 21"/ 21"/ 21 "/ 21
T
TT
T
T
T
T
Not to scale.
Certain glass aspect ratios may require tempered glass.
Size Tables - Fixed
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-11
250 Series Casement
Miscellaneous Formulas
1-Wide—Vent 1-Wide—fixed
Visible Glass VGW = FW – 6.188"VGH = FH – 6.188"
VGW = FW – 5.125"VGH = FH – 5.125"
Actual Glass AGW = FW – 5.875"AGH = FH – 5.875"
AGW = FW – 4"AGH = FH – 4"
KEY:
AGW = Actual Glass Width AGH = Actual Glass Height FW = Frame Width FH = Frame Height VGW = Visible Glass Width VGH = Visible Glass Height COW = Clear opening width COH = Clear opening height
Clear Opening Formulas
1-Wide—Vent
Vent Area VA = (COH X COW) ÷ 144
COH COH = FH - 5.124"
COWStandard Performance COW = FW - 11.631"
Side Pivot COW = FW - 7.443"
Side pivot hardware only available on frame widths of 28" to 32"
The clear opening formulas do not apply to units with FW < 16.25”
1-Wide Vent Unit
1-Wide Fixed Unit
MINIMUM14-1/2" W x 17-1/2" H
(368 x 445)
MAXIMUM35-1/2" W x 71-1/2" H
(889 x 1 803)
MINIMUM14-1/2" W x 14-1/2" H
(368 x 368)
MAXIMUM71-1/2" W x 71-1/2" H
(1 803 x 1 803)36 sq. ft. Max.
General Notes:
• To convert areas to square meters (m 2), multiply square feet by 0.0929.• Rough Opening = Frame Dimension + 1/2".• Unit Height must be > Unit Width• Keep frame di men sions to the near est 1/8" increment.• Tempered glass must measure ≥ 18-1/2" diagonally.• If glass width to height ratio is > 5 to 1, then unit must be tempered.
open 90°.with windowshows vent areaShaded portionH
EIG
HT
CLE
AR O
PEN
ING
hardwarew/ side pivot
WIDTHOPENING
CLEAR
hardwarew/ standard
WIDTHOPENING
CLEAR
VENT AREA
Special Sizes and Dimensions
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-12
250 Series Casement
Rev. 01/24/2019
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where shown, requires performance upgrade.
Certain glass aspect ratios may require tempered glass.
Vent
Unit
Eg
ress Frame (Inches) Clear Opening (Inches)
(Vent Units Only) Vent Area Ft 2
Visible Glass
Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Width Height Ft 2 Annealed Tempered
1-3/1-6 14-1/2 17-1/2 2-7/8 12-3/8 0.2 0.6 0.7 2.5 3 LC35/LC501-3/2-0 14-1/2 23-1/2 2-7/8 18-3/8 0.4 0.9 1.0 2.5 3 LC35/LC501-3/2-4 14-1/2 27-1/2 2-7/8 22-3/8 0.4 1.1 1.2 2.5 3 LC35/LC501-3/2-6 14-1/2 29-1/2 2-7/8 24-3/8 0.5 1.2 1.3 2.5 3 LC35/LC501-3/2-8 14-1/2 31-1/2 2-7/8 26-3/8 0.5 1.3 1.5 2.5 3 LC35/LC501-3/3-0 14-1/2 35-1/2 2-7/8 30-3/8 0.6 1.5 1.7 2.5 3 LC35/LC501-3/3-6 14-1/2 41-1/2 2-7/8 36-3/8 0.7 1.7 2.0 2.5 3 LC35/LC501-3/3-8 14-1/2 43-1/2 2-7/8 38-3/8 0.8 1.8 2.2 2.5 3 LC35/LC501-3/4-0 14-1/2 47-1/2 2-7/8 42-3/8 0.8 2.0 2.4 2.5 3 LC35/LC501-3/4-6 14-1/2 53-1/2 2-7/8 48-3/8 1.0 2.3 2.7 2.5 3 LC35/LC501-3/5-0 14-1/2 59-1/2 2-7/8 54-3/8 1.1 2.6 3.1 — 3 LC35/LC501-3/5-6 14-1/2 65-1/2 2-7/8 60-3/8 1.2 2.9 3.4 — 3 LC35/LC501-3/6-0 14-1/2 71-1/2 2-7/8 66-3/8 1.3 3.2 3.8 — 3 LC35/LC501-6/1-6 17-1/2 17-1/2 5-7/8 12-3/8 0.5 0.9 0.9 2.5 3 LC35/LC501-6/2-0 17-1/2 23-1/2 5-7/8 18-3/8 0.7 1.3 1.4 2.5 3 LC35/LC501-6/2-4 17-1/2 27-1/2 5-7/8 22-3/8 0.9 1.5 1.7 2.5 3 LC35/LC501-6/2-6 17-1/2 29-1/2 5-7/8 24-3/8 1.0 1.7 1.8 2.5 3 LC35/LC501-6/2-8 17-1/2 31-1/2 5-7/8 26-3/8 1.1 1.8 2.0 2.5 3 LC35/LC501-6/3-0 17-1/2 35-1/2 5-7/8 30-3/8 1.2 2.1 2.3 2.5 3 LC35/LC501-6/3-6 17-1/2 41-1/2 5-7/8 36-3/8 1.5 2.5 2.8 2.5 3 LC35/LC501-6/3-8 17-1/2 43-1/2 5-7/8 38-3/8 1.6 2.6 2.9 2.5 3 LC35/LC501-6/4-0 17-1/2 47-1/2 5-7/8 42-3/8 1.7 2.9 3.2 2.5 3 LC35/LC501-6/4-6 17-1/2 53-1/2 5-7/8 48-3/8 2.0 3.3 3.7 2.5 3 LC35/LC501-6/5-0 17-1/2 59-1/2 5-7/8 54-3/8 2.2 3.7 4.2 2.5 3 LC35/LC501-6/5-6 17-1/2 65-1/2 5-7/8 60-3/8 2.5 4.2 4.7 2.5 3 LC35/LC501-6/6-0 17-1/2 71-1/2 5-7/8 66-3/8 2.7 4.6 5.1 — 3 LC35/LC502-0/2-0 23-1/2 23-1/2 11-7/8 18-3/8 1.5 2.0 2.1 2.5 3 LC35/LC502-0/2-4 23-1/2 27-1/2 11-7/8 22-3/8 1.8 2.5 2.6 2.5 3 LC35/LC502-0/2-6 23-1/2 29-1/2 11-7/8 24-3/8 2.0 2.7 2.8 2.5 3 LC35/LC502-0/2-8 23-1/2 31-1/2 11-7/8 26-3/8 2.2 2.9 3.0 2.5 3 LC35/LC502-0/3-0 23-1/2 35-1/2 11-7/8 30-3/8 2.5 3.4 3.5 2.5 3 LC35/LC502-0/3-6 23-1/2 41-1/2 11-7/8 36-3/8 3.0 4.0 4.2 2.5 3 LC35/LC502-0/3-8 23-1/2 43-1/2 11-7/8 38-3/8 3.2 4.2 4.5 2.5 3 LC35/LC502-0/4-0 23-1/2 47-1/2 11-7/8 42-3/8 3.5 4.7 5.0 2.5 3 LC35/LC502-0/4-6 23-1/2 53-1/2 11-7/8 48-3/8 4.0 5.3 5.7 3 3 LC35/LC502-0/5-0 23-1/2 59-1/2 11-7/8 54-3/8 4.5 6.0 6.4 3 3 LC35/LC502-0/5-6 23-1/2 65-1/2 11-7/8 60-3/8 5.0 6.7 7.1 3 3 LC35/LC502-0/6-0 23-1/2 71-1/2 11-7/8 66-3/8 5.5 7.3 7.9 3 3 LC35/LC502-4/2-4 27-1/2 27-1/2 15-7/8 22-3/8 2.5 3.1 3.2 2.5 3 LC35/LC502-4/2-6 27-1/2 29-1/2 15-7/8 24-3/8 2.7 3.4 3.5 2.5 3 LC35/LC502-4/2-8 27-1/2 31-1/2 15-7/8 26-3/8 2.9 3.6 3.7 2.5 3 LC35/LC502-4/3-0 27-1/2 35-1/2 15-7/8 30-3/8 3.3 4.2 4.3 2.5 3 LC35/LC502-4/3-6 27-1/2 41-1/2 15-7/8 36-3/8 4.0 5.0 5.2 2.5 3 LC35/LC502-4/3-8 27-1/2 43-1/2 15-7/8 38-3/8 4.2 5.3 5.5 2.5 3 LC35/LC502-4/4-0 27-1/2 47-1/2 15-7/8 42-3/8 4.7 5.9 6.1 2.5 3 LC35/LC502-4/4-6 27-1/2 53-1/2 15-7/8 48-3/8 5.3 6.7 7.0 3 3 LC35/LC502-4/5-0 27-1/2 59-1/2 15-7/8 54-3/8 6.0 7.5 7.9 3 3 LC35/LC502-4/5-6 27-1/2 65-1/2 15-7/8 60-3/8 6.7 8.3 8.8 3 3 LC35/LC502-4/6-0 27-1/2 71-1/2 15-7/8 66-3/8 7.3 9.2 9.7 — 3 LC35/LC50
1 of 2
Design Data - Vent
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-13
250 Series Casement
Rev. 01/24/2019
Vent
Unit
Eg
ress Frame (Inches) Clear Opening (Inches)
(Vent Units Only) Vent Area Ft 2
Visible Glass
Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Width Height Ft 2 Annealed Tempered
2-6/2-6 29-1/2 29-1/2 17-7/8 24-3/8 3.0 3.7 3.8 2.5 3 LC35/LC502-6/2-8 29-1/2 31-1/2 17-7/8 26-3/8 3.3 4.0 4.1 2.5 3 LC35/LC502-6/3-0 29-1/2 35-1/2 17-7/8 30-3/8 3.8 4.6 4.7 2.5 3 LC35/LC502-6/3-6 E3 29-1/2 41-1/2 17-7/8 36-3/8 4.5 5.5 5.7 2.5 3 LC35/LC502-6/3-8 E2 29-1/2 43-1/2 17-7/8 38-3/8 4.8 5.8 6.0 2.5 3 LC35/LC502-6/4-0 E2 29-1/2 47-1/2 17-7/8 42-3/8 5.3 6.4 6.7 2.5 3 LC35/LC502-6/4-6 E2 29-1/2 53-1/2 17-7/8 48-3/8 6.0 7.4 7.7 3 3 LC35/LC502-6/5-0 E2 29-1/2 59-1/2 17-7/8 54-3/8 6.7 8.3 8.6 3 3 LC35/LC502-6/5-6 E2 29-1/2 65-1/2 17-7/8 60-3/8 7.5 9.2 9.6 3 3 LC35/LC502-6/6-0 E2 29-1/2 71-1/2 17-7/8 66-3/8 8.2 10.1 10.6 — 3 LC35/LC502-8/2-8 31-1/2 31-1/2 19-7/8 26-3/8 3.6 4.4 4.4 2.5 3 LC35/LC502-8/3-0 E3 31-1/2 35-1/2 19-7/8 30-3/8 4.2 5.0 5.2 2.5 3 LC35/LC502-8/3-6 E2 31-1/2 41-1/2 19-7/8 36-3/8 5.0 6.0 6.2 2.5 3 LC35/LC502-8/3-8 E2 31-1/2 43-1/2 19-7/8 38-3/8 5.3 6.4 6.6 2.5 3 LC35/LC502-8/4-0 E2 31-1/2 47-1/2 19-7/8 42-3/8 5.8 7.0 7.3 2.5 3 LC35/LC502-8/4-6 E2 31-1/2 53-1/2 19-7/8 48-3/8 6.7 8.0 8.3 3 3 LC35/LC502-8/5-0 E2 31-1/2 59-1/2 19-7/8 54-3/8 7.5 9.0 9.4 3 3 LC35/LC502-8/5-6 E2 31-1/2 65-1/2 19-7/8 60-3/8 8.3 10.0 10.4 3 3 LC35/LC502-8/6-0 E2 31-1/2 71-1/2 19-7/8 66-3/8 9.2 11.0 11.5 — 3 LC35/LC503-0/3-0 E1 35-1/2 35-1/2 23-7/8 30-3/8 5.0 5.9 6.0 2.5 3 LC35/LC503-0/3-6 E 35-1/2 41-1/2 23-7/8 36-3/8 6.0 7.0 7.2 2.5 3 LC35/LC503-0/3-8 E 35-1/2 43-1/2 23-7/8 38-3/8 6.4 7.4 7.6 2.5 3 LC35/LC503-0/4-0 E 35-1/2 47-1/2 23-7/8 42-3/8 7.0 8.2 8.4 2.5 3 LC35/LC503-0/4-6 E 35-1/2 53-1/2 23-7/8 48-3/8 8.0 9.4 9.6 3 3 LC35/LC503-0/5-0 E 35-1/2 59-1/2 23-7/8 54-3/8 9.0 10.5 10.9 3 3 LC35/LC503-0/5-6 E 35-1/2 65-1/2 23-7/8 60-3/8 10.0 11.7 12.1 3 3 LC35/LC503-0/6-0 E 35-1/2 71-1/2 23-7/8 66-3/8 11.0 12.9 13.3 — 3 LC35/LC50
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
To convert areas to square meters (m²), multiply square feet by 0.0929.
(1) Maximum performance when glazed with the appropriate glass thickness. Second value, where shown, requires performance upgrade.
Certain glass aspect ratios may require tempered glass.
2 of 2
Design Data - Vent
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-14
250 Series Casement
Rev. 01/24/2019
Fixed
UnitFrame (Inches) Visible
Glass Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Annealed Tempered
1-3/1-3 14-1/2 14-1/2 0.6 3 3 LC501-3/1-6 14-1/2 17-1/2 0.8 3 3 LC501-3/2-0 14-1/2 23-1/2 1.2 3 3 LC501-3/2-4 14-1/2 27-1/2 1.5 3 3 LC501-3/2-6 14-1/2 29-1/2 1.6 3 3 LC501-3/2-8 14-1/2 31-1/2 1.7 3 3 LC501-3/3-0 14-1/2 35-1/2 2.0 3 3 LC501-3/3-6 14-1/2 41-1/2 2.4 3 3 LC501-3/3-8 14-1/2 43-1/2 2.5 3 3 LC501-3/4-0 14-1/2 47-1/2 2.8 3 3 LC501-3/4-6 14-1/2 53-1/2 3.2 3 3 LC501-3/5-0 14-1/2 59-1/2 3.6 — 3 LC501-3/5-6 14-1/2 65-1/2 4.0 — 3 LC351-3/6-0 14-1/2 71-1/2 4.4 — 3 LC351-6/1-3 17-1/2 14-1/2 0.8 3 3 LC501-6/1-6 17-1/2 17-1/2 1.1 3 3 LC501-6/2-0 17-1/2 23-1/2 1.6 3 3 LC501-6/2-4 17-1/2 27-1/2 2.0 3 3 LC501-6/2-6 17-1/2 29-1/2 2.1 3 3 LC501-6/2-8 17-1/2 31-1/2 2.3 3 3 LC501-6/3-0 17-1/2 35-1/2 2.6 3 3 LC501-6/3-6 17-1/2 41-1/2 3.2 3 3 LC501-6/3-8 17-1/2 43-1/2 3.3 3 3 LC501-6/4-0 17-1/2 47-1/2 3.7 3 3 LC501-6/4-6 17-1/2 53-1/2 4.2 3 3 LC501-6/5-0 17-1/2 59-1/2 4.7 3 3 LC501-6/5-6 17-1/2 65-1/2 5.3 3 3 LC351-6/6-0 17-1/2 71-1/2 5.8 — 3 LC352-0/1-3 23-1/2 14-1/2 1.2 3 3 LC502-0/1-6 23-1/2 17-1/2 1.6 3 3 LC502-0/2-0 23-1/2 23-1/2 2.4 3 3 LC502-0/2-4 23-1/2 27-1/2 2.9 3 3 LC502-0/2-6 23-1/2 29-1/2 3.1 3 3 LC502-0/2-8 23-1/2 31-1/2 3.4 3 3 LC502-0/3-0 23-1/2 35-1/2 3.9 3 3 LC502-0/3-6 23-1/2 41-1/2 4.7 3 3 LC502-0/3-8 23-1/2 43-1/2 4.9 3 3 LC502-0/4-0 23-1/2 47-1/2 5.5 3 3 LC502-0/4-6 23-1/2 53-1/2 6.2 3 3 LC502-0/5-0 23-1/2 59-1/2 7.0 3 3 LC502-0/5-6 23-1/2 65-1/2 7.8 3 3 LC352-0/6-0 23-1/2 71-1/2 8.5 3 3 LC35
(1) Maximum performance when glazed with the appropriate glass thickness.
Certain glass aspect ratios may require tempered glass.
Fixed
UnitFrame (Inches) Visible
Glass Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Annealed Tempered
2-4/1-3 27-1/2 14-1/2 1.5 3 3 LC502-4/1-6 27-1/2 17-1/2 2.0 3 3 LC502-4/2-0 27-1/2 23-1/2 2.9 3 3 LC502-4/2-4 27-1/2 27-1/2 3.5 3 3 LC502-4/2-6 27-1/2 29-1/2 3.8 3 3 LC502-4/2-8 27-1/2 31-1/2 4.1 3 3 LC502-4/3-0 27-1/2 35-1/2 4.8 3 3 LC502-4/3-6 27-1/2 41-1/2 5.7 3 3 LC502-4/3-8 27-1/2 43-1/2 6.0 3 3 LC502-4/4-0 27-1/2 47-1/2 6.6 3 3 LC502-4/4-6 27-1/2 53-1/2 7.6 3 3 LC502-4/5-0 27-1/2 59-1/2 8.5 3 3 LC502-4/5-6 27-1/2 65-1/2 9.5 3 3 LC352-4/6-0 27-1/2 71-1/2 10.4 3 3 LC352-6/1-3 29-1/2 14-1/2 1.6 3 3 LC502-6/1-6 29-1/2 17-1/2 2.1 3 3 LC502-6/2-0 29-1/2 23-1/2 3.1 3 3 LC502-6/2-4 29-1/2 27-1/2 3.8 3 3 LC502-6/2-6 29-1/2 29-1/2 4.2 3 3 LC502-6/2-8 29-1/2 31-1/2 4.5 3 3 LC502-6/3-0 29-1/2 35-1/2 5.2 3 3 LC502-6/3-6 29-1/2 41-1/2 6.2 3 3 LC502-6/3-8 29-1/2 43-1/2 6.6 3 3 LC502-6/4-0 29-1/2 47-1/2 7.2 3 3 LC502-6/4-6 29-1/2 53-1/2 8.3 3 3 LC502-6/5-0 29-1/2 59-1/2 9.3 3 3 LC502-6/5-6 29-1/2 65-1/2 10.3 3 3 LC352-6/6-0 29-1/2 71-1/2 11.3 3 3 LC352-8/1-3 31-1/2 14-1/2 1.7 3 3 LC502-8/1-6 31-1/2 17-1/2 2.3 3 3 LC502-8/2-0 31-1/2 23-1/2 3.4 3 3 LC502-8/2-4 31-1/2 27-1/2 4.1 3 3 LC502-8/2-6 31-1/2 29-1/2 4.5 3 3 LC502-8/2-8 31-1/2 31-1/2 4.9 3 3 LC502-8/3-0 31-1/2 35-1/2 5.6 3 3 LC502-8/3-6 31-1/2 41-1/2 6.7 3 3 LC502-8/3-8 31-1/2 43-1/2 7.1 3 3 LC502-8/4-0 31-1/2 47-1/2 7.8 3 3 LC502-8/4-6 31-1/2 53-1/2 8.9 3 3 LC502-8/5-0 31-1/2 59-1/2 10.0 3 3 LC502-8/5-6 31-1/2 65-1/2 11.1 3 3 LC352-8/6-0 31-1/2 71-1/2 12.2 3 3 LC35
1 of 2
Design Data - Fixed
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-15
250 Series Casement
Rev. 01/24/2019
(1) Maximum performance when glazed with the appropriate glass thickness.
Certain glass aspect ratios may require tempered glass.
Fixed
UnitFrame (Inches) Visible
Glass Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Annealed Tempered
3-0/1-3 35-1/2 14-1/2 2.0 3 3 LC503-0/1-6 35-1/2 17-1/2 2.6 3 3 LC503-0/2-0 35-1/2 23-1/2 3.9 3 3 LC503-0/2-4 35-1/2 27-1/2 4.8 3 3 LC503-0/2-6 35-1/2 29-1/2 5.2 3 3 LC503-0/2-8 35-1/2 31-1/2 5.6 3 3 LC503-0/3-0 35-1/2 35-1/2 6.5 3 3 LC503-0/3-6 35-1/2 41-1/2 7.7 3 3 LC503-0/3-8 35-1/2 43-1/2 8.2 3 3 LC503-0/4-0 35-1/2 47-1/2 9.0 3 3 LC503-0/4-6 35-1/2 53-1/2 10.3 3 3 LC503-0/5-0 35-1/2 59-1/2 11.5 3 3 LC503-0/5-6 35-1/2 65-1/2 12.8 3 3 LC353-0/6-0 35-1/2 71-1/2 14.1 3 3 LC354-0/1-3 47-1/2 14-1/2 2.8 3 3 LC504-0/1-6 47-1/2 17-1/2 3.7 3 3 LC504-0/2-0 47-1/2 23-1/2 5.5 3 3 LC504-0/2-4 47-1/2 27-1/2 6.6 3 3 LC504-0/2-6 47-1/2 29-1/2 7.2 3 3 LC504-0/2-8 47-1/2 31-1/2 7.8 3 3 LC504-0/3-0 47-1/2 35-1/2 9.0 3 3 LC504-0/3-6 47-1/2 41-1/2 10.8 3 3 LC504-0/3-8 47-1/2 43-1/2 11.4 3 3 LC504-0/4-0 47-1/2 47-1/2 12.5 3 3 LC504-0/4-6 47-1/2 53-1/2 14.3 3 3 LC504-0/5-0 47-1/2 59-1/2 16.1 5 3 LC504-0/5-6 47-1/2 65-1/2 17.9 3 3 LC354-0/6-0 47-1/2 71-1/2 19.6 3 3 LC354-6/1-3 53-1/2 14-1/2 3.2 3 3 LC504-6/1-6 53-1/2 17-1/2 4.2 3 3 LC504-6/2-0 53-1/2 23-1/2 6.2 3 3 LC504-6/2-4 53-1/2 27-1/2 7.6 3 3 LC504-6/2-6 53-1/2 29-1/2 8.3 3 3 LC504-6/2-8 53-1/2 31-1/2 8.9 3 3 LC504-6/3-0 53-1/2 35-1/2 10.3 3 3 LC504-6/3-6 53-1/2 41-1/2 12.3 3 3 LC504-6/3-8 53-1/2 43-1/2 13.0 3 3 LC504-6/4-0 53-1/2 47-1/2 14.3 3 3 LC504-6/4-6 53-1/2 53-1/2 16.3 5 3 LC504-6/5-0 53-1/2 59-1/2 18.4 5 3 LC504-6/5-6 53-1/2 65-1/2 20.4 3 3 LC354-6/6-0 53-1/2 71-1/2 22.4 3 5 LC35
Fixed
UnitFrame (Inches) Visible
Glass Ft 2
Standard Glass Thickness (mm) Performance
Class & Grade 1Width Height Annealed Tempered
5-0/1-3 59-1/2 14-1/2 3.6 — 3 LC505-0/1-6 59-1/2 17-1/2 4.7 3 3 LC505-0/2-0 59-1/2 23-1/2 7.0 3 3 LC505-0/2-4 59-1/2 27-1/2 8.5 3 3 LC505-0/2-6 59-1/2 29-1/2 9.3 3 3 LC505-0/2-8 59-1/2 31-1/2 10.0 3 3 LC505-0/3-0 59-1/2 35-1/2 11.5 3 3 LC505-0/3-6 59-1/2 41-1/2 13.8 3 3 LC505-0/3-8 59-1/2 43-1/2 14.6 3 3 LC505-0/4-0 59-1/2 47-1/2 16.1 5 3 LC505-0/4-6 59-1/2 53-1/2 18.4 5 3 LC505-0/5-0 59-1/2 59-1/2 20.6 5 3 LC505-0/5-6 59-1/2 65-1/2 22.9 5 5 LC355-0/6-0 59-1/2 71-1/2 25.2 5 5 LC356-0/1-3 71-1/2 14-1/2 4.4 — 3 LC356-0/1-6 71-1/2 17-1/2 5.8 — 3 LC356-0/2-0 71-1/2 23-1/2 8.5 3 3 LC356-0/2-4 71-1/2 27-1/2 10.4 3 3 LC356-0/2-6 71-1/2 29-1/2 11.3 3 3 LC356-0/2-8 71-1/2 31-1/2 12.2 3 3 LC356-0/3-0 71-1/2 35-1/2 14.1 3 3 LC356-0/3-6 71-1/2 41-1/2 16.9 3 3 LC356-0/3-8 71-1/2 43-1/2 17.8 3 3 LC356-0/4-0 71-1/2 47-1/2 19.6 3 3 LC356-0/4-6 71-1/2 53-1/2 22.4 5 5 LC356-0/5-0 71-1/2 59-1/2 25.2 5 5 LC356-0/5-6 71-1/2 65-1/2 27.9 — 5 LC356-0/6-0 71-1/2 71-1/2 30.7 — 5 LC35
2 of 2
Design Data - Fixed
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-16
250 Series Casement
(1) Dual Pane IG High Altitude glazings are available with or without Argon. Triple Pane IG High Altitude glazings are only available without Argon.
(2) Obscure glass not available with Bronze Advanced Low-E IG.
(3) Almond grilles only available on Almond units. Almond units with grilles will have an Almond grille color, Fossil extruded color units with grilles have a Fossil grille color.
Frame • Overall frame depth: 3-1/4" on all frame types. • Frame members are mitered and heat fused to provide a fully welded
corner assembly. Sill is fitted with weeps.• Frame: [1-1/8" setback nail fin for 2-1/8" wall depth] [Block frame for 3-1/4"
wall depth] [Integral 5/8" flange for 3" wall depth]. • Interior and exterior frame surfaces are extruded rigid PVC.
Sash
• Sash members are extruded, rigid PVC [with optional foam insulation 1].• Sash members are mitered and heat-fused to provide a fully welded corner
assembly.• Contains sealed insulating glass.
Weatherstripping• Vent units include weatherstripping around the sash perimeter with a fin-
type, pile and an extruded bulb weatherstrip.
Glazing System• Quality float glass complying with ASTM C 1036.• Exterior face-glazed sealed insulating glass. • Dual-Pane insulating glass [[annealed] [tempered]] [[Advanced]
[NaturalSun] [SunDefense™] [Bronze, Advanced] Low-E coated [with Argon]] [Obscure 2] [High Altitude 1].
- or -• 1" Triple-Pane [[annealed] [tempered]] [[Advanced] [NaturalSun] Low-E
coated [with Argon]] [Obscure 2] [High Altitude 1].
Interior / Exterior• Window frame and sash members are [[White] [Almond] [Fossil] with
integral color extruded throughout the profiles] [[Brown] [Black] [Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan] [Fossil] exterior, consisting of a solar reflective coating exceeding AAMA 613 test requirements, with White integral color extruded throughout the profiles on the interior].
• All exposed PVC surfaces are smooth, glossy and uniform in appearance.
Hardware • Multi-point unison lock with single handle is factory-installed zinc die cast.
Lock tie-bars are stainless steel.• High quality [steel] [stainless steel] dual-arm roto-operator with fold down
crank handle on sill.• Hinge arms are [steel] [stainless steel].• Corrosion-resistant fasteners of PVC-compatible material.• Hardware finish is [White] [Almond] [Fossil].
Insect screen• Set in aluminum frame and fitted to interior of window.• Screen frame finish is baked enamel, color to match interior.• Supplied complete with all necessary hardware.• Conventional Black Fiberglass
� Black vinyl coated 18/16 mesh fiberglass screen cloth complying with ASTM D 3656 and SMA 1201.
Optional Products
Grilles • Grilles-Between-the-Glass
� [Dual-Pane Insulating glass contains [[3/4"] [1"] contoured] [5/8" flat] aluminum grilles permanently installed between two panes of glass] [Triple-Pane Insulating glass contains 3/4" contoured aluminum grilles permanently installed between three panes of glass].
� Patterns are [Traditional] [9-Lite Prairie] [Top Row]. � Exterior grille color [3/4" Grille is [White] [Almond 3] [Fossil 3] [Brown]
[Black] [Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan]] [1" Grille is [White] [Almond 3] [Fossil 3]] [5/8" Grille is [White] [Almond 3] [Fossil 3]].
• Simulated-Divided-Light grilles without spacer � 7/8" Grilles permanently bonded to the interior and exterior of glass. � Patterns are [Traditional] [9-Lite Prairie] [Top Row]. � Grilles match color of interior and exterior frame. � Available only on units glazed with dual-pane insulated glass.
Hardware• Optional limited opening hardware available for vent units in [White]
[Almond] [Fossil] extruded vinyl to match the unit; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4" with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-10.
Detailed Product Description
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-17
250 Series Casement
Scale 3" = 1' 0" All dimensions are approximate.
[83]3 1/4" OAW
HINGE JAMB
VENT HEAD
SILLOPERATOR
LOCK JAMB
Unit Sections - Optional Foam Insulation
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-18
250 Series Casement
Scale 3" = 1' 0" All dimensions are approximate.
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[63]2 1/2"
[65]
2 9/
16"
[63]2 1/2"
[65]
2 9/
16"
[63]2 1/2"
[65]
2 9/
16"
1" Insulating Glass
3/4"
[29]
1 1/
8"
[54]2 1/8"
[19]3/4"
[19]3/8"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[65]
2 9/
16"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"[5
7]2
1/4"
[77]3"
[6]1/4"
[65]
2 9/
16"
[79]
3 1/
16"
[58]
2 1/
4"[1
6]5/
8"
[65]
2 9/
16"
[16]
5/8"
[77]3"
[6]1/4"
[63]2 1/2"
[83]3 1/4" OAW
[79]
3 1/
16"
[65]
2 9/
16"
[58]
2 1/
4"[1
6]5/
8"
[54]2 1/8"
[29]1 1/8"
[29]
1 1/
8"
[65]
2 9/
16"
GLAZING OPTIONS
1" Triple Pane IG3/4" Insulating Glass
5/8" INTEGRAL FLANGEBLOCK FRAME with
with J-CHANNELNAIL FIN
NAIL FINSTANDARD
FLUSH FLANGE
BLOCK FRAMESTANDARD
Unit Sections - Frame Types
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-19
250 Series Casement
Scale 3" = 1' 0" All dimensions are approximate.
[16]
5/8"
4 9/16" Wall
[62]2 7/16"
[29]1 1/8"
[63]
2 1/
2"
6 9/16" Wall4 9/16" Wall
[63]2 1/2"
[29]
1 1/
8"
[16]5/8"
[58]2 1/4"
[79]3 1/16"
FRAME WIDTH
[29]1 1/8"
[62]2 7/16"
Optional Factory Applied Wood Jamb Extensions
[113]4 7/16"
[16]
5/8"
[29]
1 1/
8"[5
4]2
1/8"
[20]13/16"
[59]2 5/16"
[167]6 9/16"
[116]4 9/16"
1 1/8"[54]
2 1/8"
[58]
2 1/
4"[1
6]5/
8"
FRAM
E H
EIG
HT
[79]
3 1/
16"
[83]3 1/4" OAW
VH
LJ
VS
HJ
LOCK JAMBLJHINGE JAMBHJ
VS VENT SILL
VH VENT HEAD
Unit Sections - Nail Fin
Pella 2019 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com V250-CM-20
250 Series Casement
Scale 3" = 1' 0" All dimensions are approximate.
[79]
3 1/
8"
[16]5/8"
[49]1 15/16"
[65]2 9/16"
FRAME WIDTH
[83]
3 1/
4"
[20]13/16"
[59]2 5/16"
[79]3 1/16"
[63]
2 1/
2"
FRAME WIDTHFRAME WIDTH 1/2" [13]
TOTAL FRAME WIDTH
[170]6 11/16"
[143]5 5/8"
[83]
3 1/
4"
[79]
3 1/
8"
[63]
2 1/
2"
FRAME WIDTH1/2" [13]
[20]13/16"
[59]2 5/16"
[79]3 1/16"
FRAME WIDTHFRAME WIDTH 1/2" [13]
TOTAL FRAME WIDTH
[156]6 1/8"
[83]3 1/4" OAW
[79]3 1/8"
[65]
2 9/
16"
[49]
1 15
/16"
[16]
5/8"
FRAM
E W
IDTH
[83]3 1/4"
[63]2 1/2"
[58]
2 1/
4"[1
6]5/
8"
FRAM
E H
EIG
HT
[79]
3 1/
16"
[83]3 1/4" OAW
FJ
FH
FS
HJ VIM
VIMVIM
FH
FS
VH
VS
HJ
VH
VS
FJ FIXED JAMB
HINGE JAMBHJHINGE JAMBHJ LOCK JAMBLJLOCK JAMBLJ
INTEGRAL MULLIONVERTICALVIM
INTEGRAL MULLIONVERTICALVIM
FJ FIXED JAMB FJ FIXED JAMB HINGE JAMBHJHINGE JAMBHJ LOCK JAMBLJLOCK JAMBLJ
INTEGRAL MULLIONVERTICALVIM
FH FIXED HEAD
FS FIXED SILLVS VENT SILL
VH VENT HEAD
Unit Sections - Block Frame