roof underlay | wall lining | façades

Permanent safe

ConstructionsOptimal external sealing for perfect windtightness and insulation

2© pro clima 07.2014 | www.proclima.com

Exterior wind sealing with sarking Exterior Construction

Exterior wind sealing Sarking

Structure of hip and ridge

1

2

Valley detail

1

2

Sticking and overlapping

1

2

Sealing at bargeboard

1 4

Legend

Underlay or sarking membranesSOLITEX MENTO family*) SOLITEX UDSOLITEX PLUS*)

Adhesive tape TESCON VANATESCON No.1

Nail sealing tapeTESCON NAIDEC

Joint adhesiveORCON FORCON CLASSIC

connect technology (integrated self-adhesive zones)

Double-sided adhesive tape DUPLEX

Pipe grommetROFLEX **)

Chimney insulated, double-wall

Protruding lath

Separation lath

Position held by 3-4 mm ofhard fibre or chipboard strip, for example.

Rafter

Counter lath

Info

*) For blown-in insulation, the use of reinforced SOLITEX PLUS or SOLITEX MENTO PLUS is recom-mended

**) Alternatively, pipes can be sealed using short strips of TESCON VANA or TESCON No.1.

1

6 5

Alternative

Sealing at eaves

1

6

Alternative

2

1

8

10

9

11

12

13

3

2

4

5

6

7

3 © pro clima 07.2014 | www.proclima.com

Exterior Construction Exterior wind sealing with sarking

When using pro clima SOLITEX membranes, the entire cavity can be filled with insulation. Complicated and often ineffective replace with: “ventilation between the membrane and the insulation” at the eaves, ridge, valley, hip and additional roof features are thus unnecessary.

Tips

A Allow for cross-drainage above the component

B Ensure that there is water- proof adhesion all around the circumference. • 1st strip on bottom • 2nd + 3rd strip left • Last strip at top

C Leave slack when applying the membrane to allow for relative motion between components.

D Stick with ORCON F or ORCON CLASSIC if necessary

E Alternative: EXTOSEAL MAGOV

F Alternative: EXTOSEAL FINOC

Detail view of nail sealing

1 3

Sealing at dormer window

1

1

1

2

2

Sealing at skylights incl. sheeting channel

A

1

2

2

Retrofit installation of wind sealing/rear ventilation layer

1 D

B

E

1

2 7

Pipe or cable feed-throughs

C A

C

A 1

4

4

Chimney penetration

Please also observe the gene- ral information on sealing to chimneys on page 8 (Interior Construction).

8

13

10 9

1112

F

4© pro clima 07.2014 | www.proclima.com

Exterior wind sealing for facades Exterior Construction

Exterior wind sealingFacade

Standard structure, closed facade

Standard structure, timber wall behind ventilated masonry wall

Window sill in timber construction

Standard structure, partially open facade

Legend

Wall lining membraneSOLITEX FRONTA WA*)

Wall lining membraneSOLITEX FRONTA QUATTRO*)

Wall lining membraneSOLITEX FRONTA HUMIDA*)

Sealing tape TESCON VANA TESCON No.1 TESCON PROFIL

Window sealing tapeCONTEGA EXO**)

Window sealing tapeCONTEGA IQ**)

Joint adhesiveORCON FORCON CLASSICor DUPLEX double-sided adhesive tape

EXTOSEAL ENCORS waterproof adhesive tape

Gap lining

Pre-wall shell

Air layer

Wood fibre insulating panel

Compartment insulation

Vapour retarding and airtightness layer, e.g. wood-based panel

Installation layer

Exterior plastering

Info

*) To improve windproofing, stick SOLITEX membranes to each other and to all adjacent components.

**) Gypsum plasters have very good adhesion on CONTEGA fleece. A bonding bridge – e.g. a reinforcing mortar – must be used for lime and cement plasters.

Facade, window sealing

1

7

2

11

1

10

14

3

2

4

5

7

8

6

15

13

12

11

9

16

1

14 14

2

15 15

13 13

12 1211 11

9

14

3

10 8

15

13

13

1211 12 1416

4 5

Alternative

5

Alternative

6

1

1

2

2

5 © pro clima 07.2014 | www.proclima.com

Exterior Construction Exterior wind sealing for facades

Sealing at windows, at the side of the frame, masonry wall

5 6

6 5

Sealing at windows, on the frame, masonry wall

5

5

4

4

2014

-07

DIG

-248

INTELLO maximum reliability system

INTELLO vapour retarder and air sealing systemMaximum protection against structural damage and mould – also for sophisticated civil engineering structures.Humidity-variable sd value 0.25 to >25 m.

New protection for existing structures – the DASATOP system

The DASATOP sub-and-top refurbishment systemOptimised for roof restoration from the outside.Quick, simple, reliable!

Best possible protection for roofs and walls – the SOLITEX system

Highly permeable roof lining and facade membranes The best quality for reliable structures that are free of structural damage and mould for roofs and walls.

Secure bonding and detail solutions

• All-round adhesive tapes and joint adhesives for interior and exterior use• Plaster sealing tapes• Sealing grommets

You can also visit pro clima ONLINE!

Further information and background information at

Information and orderingYou can obtain information on all pro clima systems, tender information and brochures quickly and simply by contacting our information service:Phone: +49 (0) 62 02 – 27 82.0Fax: +49 (0) 62 02 – 27 82.21eMail: info@proclima.com

Interior air sealing

Refurbishment and modernisation

Exterior wind sealing

Additional system solutions for

sealing of the building envelope

www.proclima.com

The applications and conditions described here are based on current state-of-the-art research and practical experience. We reserve the right to change the recommended structures and processing methods and to further develop and thus alter the quality of individual products. We would be glad to inform you about the current state of engineering knowledge at the time that your installation is carried out.

www.proclima.com

MOLL bauökologische Produkte GmbHRheintalstraße 35–43D-68723 SchwetzingenGermany

+49 (0) 62 02 - 27 82.0+49 (0) 62 02 - 27 82.21

info@proclima.com