ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2001 ARP3110 MEDIA RECEIVER PDP-R03E 1. SAFETY INFORMATION ...................................... 3 2. EXPLODED VIEWS AND PARTS LIST ................ 4 3. BLOCKDIAGRAM AND SCHEMATIC DIAGRAM ... 8 4. PCB CONNECTION DIAGRAM .......................... 64 5. PCB PARTS LIST ............................................... 71 6. ADJUSTMENT .................................................... 96 CONTENTS 7. GENERAL INFORMATION .............................. 102 7.1 DIAGNOSIS ............................................... 102 7.1.1 TROUBLE SHOOTING ...................... 102 7.1.2 DISASSEMBLY .................................. 107 7.2 EXPLANATION .......................................... 108 7.2.1 IC DESCRIPTIONS ............................ 108 8. PANEL FACILITIES AND SPECIFICATIONS .. 110 THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). T – ZZK NOV. 2001 Printed in Japan POWER STANDBY/ON MEDIA RECEIVER PDP-R03E Type Model Power Requirement Remarks PDP-R03E WYVI6 AC220-240V For details, refer to "Important symbols for good services" on the next page. Component System Service Manual Remarks PLASMA DISPLAY SYSTEM PDP-503HDE PDP-433HDE ––– PLASMA DISPLAY PDP-503PE ––– ARP3107, ARP3108 ––– PDP-433PE ARP3111, ARP3112 MEDIA RECEIVER PDP-R03E ARP3110 This manual. ¶ Please connect it to the PLASMA DISPLAY PDP-503PE or PDP-433PE, for adjustment and operation inspection.
Transcript
ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, JapanPIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, BelgiumPIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2001
ARP3110
MEDIA RECEIVER
PDP-R03E
1. SAFETY INFORMATION ...................................... 3
2. EXPLODED VIEWS AND PARTS LIST ................ 4
7.2.1 IC DESCRIPTIONS ............................ 108
8. PANEL FACILITIES AND SPECIFICATIONS .. 110
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
T – ZZK NOV. 2001 Printed in Japan
POWER
STANDBY/ON
MEDIA RECEIVER PDP-R03E
TypeModel
Power Requirement RemarksPDP-R03E
WYVI6 AC220-240V
For details, refer to "Important symbols for good services" on the next page.
Component System Service Manual Remarks
PLASMA DISPLAY SYSTEM PDP-503HDE PDP-433HDE –––
PLASMA DISPLAYPDP-503PE ––– ARP3107, ARP3108
––– PDP-433PE ARP3111, ARP3112
MEDIA RECEIVER PDP-R03E ARP3110 This manual.
¶ Please connect it to the PLASMA DISPLAY PDP-503PE or PDP-433PE, for adjustmentand operation inspection.
PDP-R03E
2
[ Important symbols for good services ]In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely.When you find the procedures bearing any of the symbols, be sure to fulfill them:
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning,proper cleaning should be performed to restore their performances.
5. Lubricants, glues, and replacement partsAppropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply theprescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used.
4. Shipping mode and shipping screws
To protect the product from damages or failures that may be caused during transit, the shipping mode should be set orthe shipping screws should be installed before shipping out in accordance with this manual, if necessary.
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
PDP-R03E
3
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casualdo-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have beentrained to properly and safely repair complex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and mayvoid the warranty. If you are not qualified to perform the repair of this product properly and safely, youshould not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to
cause cancer, bir th defects or other reproductive harm.
Health & Safety Code Section 25249.6 – Proposition 65
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement
parts must be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que
les pièces de remplacement doivent avoir la même désignation.
ANY MEASUREMENTS NOT WITHIN THELIMITS OUTLINED ABOVE ARE INDICATIVEOF A POTENTIAL SHOCK HAZARD ANDMUST BE CORRECTED BEFORE RETURN-ING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICEMany electrical and mechanical parts in the appliance
have special safety related characteristics. These areof ten not evident f rom visual inspect ion nor theprotection afforded by them necessarily can be obtainedby using replacement components rated for voltage,wattage, etc. Replacement parts which have thesespecial safety character ist ics are ident i f ied in thisService Manual.
Electr ical components having such features areidentified by marking with a on the schematics andon the parts list in this Service Manual.The use of a substitute replacement component whichdoes not have the same safety characteristics as thePIONEER recommended replacement one, shown in theparts list in this Service Manual, may create shock, fire,or other hazards.
Product Safety is continuously under review and newinstructions are issued from time to time. For the latestinformat ion, a lways consul t the current PIONEERService Manual. A subscription to, or additional copiesof, PIONEER Service Manual may be obtained at anominal charge from PIONEER.
(FOR USA MODEL ONLY)1. SAFETY PRECAUTIONS
The following check should be performed for thecont inued protect ion of the customer and serv icetechnician.
LEAKAGE CURRENT CHECKMeasure leakage current to a known earth ground
(water pipe, conduit, etc.) by connecting a leakagecur ren t tes te r such as S impson Mode l 229-2 o requivalent between the earth ground and all exposedmetal parts of the appliance (input/output terminals,screwheads, metal overlays, control shaft, etc.). Plugthe AC line cord of the appliance directly into a 120VAC 60 Hz outlet and turn the AC power switch on. Anycurrent measured must not exceed 0.5 mA.
Deviceundertest
Leakagecurrenttester
Earthground
Reading shouldnot be above0.5 mA
Also test withplug reversed(Using AC adapterplug as required)
Test allexposed metalsurfaces
AC Leakage Test
PDP-R03E
4
2.1 PACKING
2. EXPLODED VIEWS AND PARTS LIST
FRONT
10. Packing Case
14. No. Label
4. Remote Control Unit
11. Buffer Material
11. Buffer Material
12. Packing Material
13. Polyethylene Bag
6. Operation Instructions
7. Operation Instructions
8. System Cable Caution
9. Caution Card
5. Batteries
1. Power Cord
2. Power Cord
3. System Cable
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.(In the case of no amount instructions, apply as you think it appropriate.)
NOTES:
PDP-R03E
5
• PACKING PARTS LISTMark No. Description Part No. 1 Power Cord (For Europe) QACCBA005WJZZ 2 Power Cord (For U.K.) QACCVA002WJZZ
3 System Cable QCNW-6117CEZZ4 Remote Control Unit RRMCG1677CESA
CVIC INTERNAL SUPPLY VOLTAGE SELECTORR1077 MOUNTED: VD+2.5V=2.5VR1078 MOUNTED: VD+2.5V=1.8V
CVIC INTERNAL SUPPLY VOLTAGE MONITORR1105 MOUNTED: VD+2.5V=2.5VR1106 MOUNTED: VD+2.5V=1.8V
PC DDC
DETECT
FLASH WRITE AT FWMODEN=LOW
A
B
C
D
1 2 3 4
1 2 3 4
18
PDP-R03E
3.1.6 PRINTED WIRING BOARD BLOCK DIAGRAM
U/V
TU
NE
R
IC1601TELTEXT
IC1602FLASH MEMORY
IC1603SRAM
IC2501MULTI SOUND
P2502CONNECTOR
IC1301AV SWITCH
P1301CONNECTOR
SC1401CONNECTOR
SC1402CONNECTOR
P2503CONNECTOR
P2501CONNECTOR
IC1401AV SWITCH
SC1101SCART-1 TERMINAL
SC1102SCART-2/3 TERMINAL
J1101COMP IN/MONI-OUT TERMINAL
IC1102CONTROL
J1102MONITOR S-OUT
TELTEXT & AV LINKCIRCUIT
COMP. AV SWITCHCIRCUIT
ANALOG AV SWITCHCIRCUIT
CPCI-0056CECPCI-0056CECPCI-0056CECPCI-0056CE
CN1CONNECTOR
CN7CONNECTOR
CN6CONNECTOR
IC25CIVIC
IC1CPU
IC310A/D CONV
IC4VIDEO MAIN/PC
A/D CONV
IC413PANEL LINK
IC319SDRAM
IC320SDRAM
CN
9C
ON
NE
CTO
RC
N8
CO
NN
EC
TOR
IC7REG.
IC8REG.
CN
5R
S-2
32C
CN
3D
ISP
LAY
OU
T-1
IC405RS-323 RECIVER
PANEL LINKOUTPUTCIRCUIT
RS-232C LINEDRIVER I/FCIRCUIT
VIDEO IN A/DCONVERTERCIRCUIT
POWER REG.CIRCUIT
PC R,G,B INPUTCIRCUIT
CPU CIRCUIT
VIDEO PROCESSORCIRCUIT
PC I/F UNIT
AV UNIT
F
C
A
B
C
D
5 6 7 8
5 6 7 8
19
PDP-R03E
DC/DC CONVERTERCIRCUIT
P1703CONNECTOR
IC1502DAC
IC801MAIN VIDEO
CHROMA
IC604SYNC SEP.
IC803RGB DECODER
P15
02C
ON
NE
CTO
R
P901ADJUSTINGCONNECTOR
P1702CONNECTOR
SC
1502
CO
NN
EC
TOR
SC
1501
CO
NN
EC
TOR
IC403CONTROL
IC406CONTROL
IC802SUB VIDEOCHROMA
SC1503CONNECTOR
IC402SUB COMB FIL.
IC405MAIN COMB FIL.
IC901PLD
SC
1504
CO
NN
EC
TOR
PO
WE
R S
UP
PLY
MAIN UNITA
20
PDP-R03E
DESCRIPTION OF SCHEMATIC DIAGRAMVOLTAGE MEASUREMENT CONDITION:1. When the exclusive-use AC adapter is used, the colour bar signal
of colour bar generator for service is input to get the normal screen.When the audio is minimized, the voltage value is measured withthe 20 kΩ/V tester.
WAVEFORM MEASUREMENT CONDITION:1. When the exclusive-use AC adapter is used, the colour density,
lightness and colour hue are set to the center position, and thesignal of colour bar generator for service is observed to getwaveform.
2. indicates waveform check points (See chart, waveforms aremeasured from point indicated to chassis ground.)
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)3. All resistors are Carbon type, unless otherwise noted.
C : Solid W : CementS : Oxide Film T : SpecialN : Metal Coating
CAPACITOR1. All capacitors are mF, unless otherwise noted.
(P=pF=mmF).2. All capacitors are Ceramic type, unless otherwise noted.
CAUTION:This circuit diagram is original one, therefore there may be aslight difference from yours.
IMPORTANT SAFETY NOTICE:PARTS MARKED WITH “ ” ( )AREIMPORTANT FOR MAINTAINING THE SAFETY OFTHE SET. BE SURE TO REPLACE THESE PARTSWITH SPECIFIED ONES FOR MAINTAINING THESAFETY AND PERFORMANCE OF THE SET.
21
PDP-R03E
WAVEFORMS1
IC1301 63-pin
V: 200mV/div H: 10µsec/div
2
IC1301 56-pin
V: 500mV/div H: 10µsec/div
3
IC405 1, 2-pin
V: 500mV/div H: 10µsec/div
4
IC801 1-pin
V: 200mV/div H: 10µsec/div
5
IC803 TP801
V: 200mV/div H: 20µsec/div
6
IC803 TP802
V: 200mV/div H: 20µsec/div
7
IC803 TP803
V: 200mV/div H: 20µsec/div
8
IC803 31-pin
V: 1V/div H: 20µsec/div
9
IC810 13-pin
V: 500mV/div H: 20µsec/div
0
IC810 11-pin
V: 500mV/div H: 20µsec/div
-
IC810 10-pin
V: 500mV/div H: 20µsec/div
A
B
C
D
1 2 3 4
1 2 3 4
22
PDP-R03E
CN9 CN8
CN
703
CN702
CN
6C
N7
CN
1
QCNW-6077CEZZ
QCNW-6083CEZZ
QCNW-6084CEZZ
PDP-R03E
P3001
P6000 P6001
PC I/F UNITF
SR CONNECT UNIT
LED UNIT
POWER UNIT
EMC UNIT
G
HD
E
3.2 OVERALL WIRING DIAGRAM (1/2)
A
B
C
D
5 6 7 8
5 6 7 8
23
PDP-R03E
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
TU
NE
R
P2401 P2402
P1703
SC1503
SC1401
P13
01
P2502
P25
01
P25
03
SC
14
02
SC
15
04
SC
15
02
SC
15
01
P1702
P15
02
QCNW-6073CEZZ
QCNW-6075CEZZ
QCNW-6082CEZZ
QCNW-6079CEZZ
QCNW-6076CEZZ
QCNW-6074CEZZ
QCNW-6081CEZZ
QCNW-6080CEZZ
QCNW-6078CEZZ
MAIN UNITA
AV UNIT
FRONT UNIT
C
B
A
B
C
D
1 2 3 4
1 2 3 4
24
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F F 1/7-7/7
AV UNIT (DUNTKA537DE01)
FRONT UNIT (DUNTKA536DE01)
SR CONNECT UNIT
(DUNTKA 594DE01)
(DUNTKA 649DE01)
LED UNIT
C C 1/3-3/3
B
D
E
3.3 OVERALL WIRING DIAGRAM (2/2)
A
B
C
D
5 6 7 8
5 6 7 8
25
PDP-R03E
MAIN UNIT (DUNTKA535DE01)
A A 1/6-6/6
POWER UNIT (RDENC0331CEZZ)
EMC UNIT (RDENCA 006WJZZ)
G
H
A
B
C
D
1 2 3 4
1 2 3 4
26
PDP-R03E
A 1/6 MAIN UNIT (DUNTKA535DE01)
1/6A
3.4 MAIN UNIT (1/6)
A
B
C
D
5 6 7 8
5 6 7 8
27
PDP-R03E
2/6A
4/6A
6/6A
3/6A
4/6A
3/6A
5/6A
6/6A
1/6A
A
B
C
D
1 2 3 4
1 2 3 4
28
PDP-R03E
A 2/6 MAIN UNIT (DUNTKA535DE01)
1/6A
1/6A
1/6A
2/6A
3.5 MAIN UNIT (2/6)
A
B
C
D
5 6 7 8
5 6 7 8
29
PDP-R03E
5/6A
6/6A
5/6A
4/6A
3/6A
5/6A
5/6A
5/6A
3/6A
6/6A
2/6A
A
B
C
D
1 2 3 4
1 2 3 4
30
PDP-R03E
A 3/6 MAIN UNIT (DUNTKA535DE01)1/6A
2/6A
2/6A
3/6A
3.6 MAIN UNIT (3/6)
A
B
C
D
5 6 7 8
5 6 7 8
31
PDP-R03E
6/6A
6/6A
5/6A
3/6A
A
B
C
D
1 2 3 4
1 2 3 4
32
PDP-R03E
A 4/6 MAIN UNIT (DUNTKA535DE01)
1/6A
6/6A
2/6A
5/6A
5/6A
4/6A
3.7 MAIN UNIT (4/6)
A
B
C
D
5 6 7 8
5 6 7 8
33
PDP-R03E
6/6A
5/6A
2/6A
2/6A
2/6A
1/6A
1/6A
1/6A
4/6A
A
B
C
D
1 2 3 4
1 2 3 4
34
PDP-R03E
A 5/6 MAIN UNIT (DUNTKA535DE01)
1/6A
2/6A
3/6A
4/6A
CN6F 7/7
SC
1401
C2/3
5/6A
3.8 MAIN UNIT (5/6)
A
B
C
D
5 6 7 8
5 6 7 8
35
PDP-R03E
6/6A
SC
1402
C2/3
CN
703
G
CN7F 2/7
5/6A
A
B
C
D
1 2 3 4
1 2 3 4
36
PDP-R03E
A 6/6 MAIN UNIT (DUNTKA535DE01)
1/6A
2/6A
3/6A
4/6A
5/6A
5/6A
5/6A
6/6A
3.9 MAIN UNIT (6/6)
A
B
C
D
5 6 7 8
5 6 7 8
37
PDP-R03E
CN
9F
7/7P
2501
C2/3
6/6A
A
B
C
D
1 2 3 4
1 2 3 4
38
PDP-R03EC
N8
F3/7
FRONT UNIT (DUNTKA536DE01)B
SW3401 : CLEAR
B
3.10 FRONT UNIT
A
B
C
D
5 6 7 8
5 6 7 8
39
PDP-R03E
P13
01C
2/3
B
A
B
C
D
1 2 3 4
1 2 3 4
40
PDP-R03E
C 1/3 AV UNIT (DUNTKA537DE01)
1/3C
3.11 AV UNIT (1/3)
A
B
C
D
5 6 7 8
5 6 7 8
41
PDP-R03E
2/3C
2/3C
3/3C
1/3C
A
B
C
D
1 2 3 4
1 2 3 4
42
PDP-R03E
C 2/3
3/3C
1/3
P60
01D
C
AV UNIT (DUNTKA537DE01)P
3402
B
2/3C
3.12 AV UNIT (2/3)
A
B
C
D
5 6 7 8
5 6 7 8
43
PDP-R03E
3/3C
3/3C
SC
1503
A5/6
SC
1504
A5/6
P1703A 6/6
P30
01E
2/3C
A
B
C
D
1 2 3 4
1 2 3 4
44
PDP-R03E
C 3/3
2/3C
2/3C
2/3C
1/3C
AV UNIT (DUNTKA537DE01)
3/3C
3.13 AV UNIT (3/3)
A
B
C
D
5 6 7 8
5 6 7 8
45
PDP-R03E
3/3C
A
B
C
D
1 2 3 4
1 2 3 4
46
PDP-R03E
D
3.14 SR CONNECT UNIT
P2502C 2/3CN1F 7/7
SR CONNECT UNIT (DUNTKA594DE01)D
A
B
C
D
1 2 3 4
1 2 3 4
47
PDP-R03E
E
3.15 LED UNIT
LED UNIT (DUNTKA649DE01)E
P2503C 2/3
A
B
C
D
1 2 3 4
1 2 3 4
48
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 1/7
2/7F
7/7F
2/7F
5/7F
7/7F
3/7F
5/7F
1/7F
3.16 PC I/F UNIT (1/7)
A
B
C
D
5 6 7 8
5 6 7 8
49
PDP-R03E
7/7F4/7F5/7F
2/7F
3/7F
7/7F
5/7F
2/7F
7/7F
5/7F
2/7F
5/7F
3/7F
2/7F
1/7F
A
B
C
D
1 2 3 4
1 2 3 4
50
PDP-R03E
1/7F
1/7F
1/7F
5/7F
1/7F
1/7F
1/7F
SC1502A 5/62/7F
3.17 PC I/F UNIT (2/7)
A
B
C
D
5 6 7 8
5 6 7 8
51
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 2/7
3/7F7/7F
5/7F
3/7F
4/7F
4/7F
7/7F
2/7F
A
B
C
D
1 2 3 4
1 2 3 4
52
PDP-R03E
1/7F
2/7F
4/7F
7/7F
7/7F
1/7F2/7F7/7F
5/7F
P34
01B
3/7F
3.18 PC I/F UNIT (3/7)
A
B
C
D
5 6 7 8
5 6 7 8
53
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 3/7
4/7F
5/7F
5/7F
3/7F
A
B
C
D
1 2 3 4
1 2 3 4
54
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 4/7
2/7F
3/7F
5/7F
7/7F
2/7F
7/7F
7/7F
4/7F
3.19 PC I/F UNIT (4/7)
A
B
C
D
5 6 7 8
5 6 7 8
55
PDP-R03E
5/7F
7/7F
5/7F
4/7F
A
B
C
D
1 2 3 4
1 2 3 4
56
PDP-R03E
2/7F4/7F7/7F4/7F3/7F
1/7F
2/7F
3/7F
4/7F
3/7F
7/7F
5/7F
3.20 PC I/F UNIT (5/7)
A
B
C
D
5 6 7 8
5 6 7 8
57
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 5/7 6/7F
2/7F 6/7F 7/7F 1/7F 6/7F
5/7F
A
B
C
D
1 2 3 4
1 2 3 4
58
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)
F 6/7
5/7F
5/7F6/7F
3.21 PC I/F UNIT (6/7)
A
B
C
D
5 6 7 8
5 6 7 8
59
PDP-R03E
7/7F
6/7F
A
B
C
D
1 2 3 4
1 2 3 4
60
PDP-R03E
PC I/F UNIT (CPCI-0056CE11)F 7/7
3/7F
2/7F
1/7F
3/7F
4/7F
5/7F6/7F
4/7F
5/7F
1/7F
P17
02A
6/6P
6000
D
7/7F
3.22 PC I/F UNIT (7/7)
A
B
C
D
5 6 7 8
5 6 7 8
61
PDP-R03E
2/7F
SC
1501
A5/6
7/7F
A
B
C
D
1 2 3 4
1 2 3 4
62
PDP-R03E
EMC UNIT (RDENCA006WJZZ)
(LIVE)
(NEUTRAL)
(LIVE)
(NEUTRAL)
H
• NOTE FOR FUSE REPLACEMENTFOR CONTINUED PROTECTION AGAINST RISK OF FIRE.REPLACE WITH SAME TYPE AND RATINGS ONLY.
CAUTION -
(LIVE)
(NEUTRAL)
G
3.23 POWER and EMC UNITS
H
A
B
C
D
5 6 7 8
5 6 7 8
63
PDP-R03E
P15
02A
5/6
POWER UNIT (RDENC0331CEZZ)G
G
A
B
C
D
1 2 3 4
1 2 3 4
64
PDP-R03E
IC1706
IC1704
IC1502
Q7001
Q424
Q427
Q616
Q619
IC7001
IC7004
IC405
IC402IC604
IC603
IC801
IC406
IC403
IC803
IC7200
IC802
IC807IC1903
IC1901
MAIN UNITA
SIDE ACN7F
SC1402C
CN9F
P2501C
SC1401C
CN6F CN703G
NOTE FOR PCB DIAGRAMS :• Part numbers in PCB diagrams match those in the schematic
diagrams.• The parts mounted on this PCB include all necessary parts for
several destinations.For further information for respective destinations, be sure tocheck with the schematic diagram.
• View point of PCB diagrams.
CapacitorConnector
P.C.Board Chip Part
SIDE A
SIDE B
Q818
Q827
Q1508
Q1511
4.1 MAIN UNIT
A
4. PCB CONNECTION DIAGRAM
A
B
C
D
1 2 3 4
1 2 3 4
65
PDP-R03E
Q1710Q1718
Q1701
Q1708
Q1719Q1713
Q1716Q1726Q1712
IC1701
IC1713
IC1504
IC1710
IC1711
IC1712
Q601
Q615
Q621
IC7003
IC7002
IC602
IC1708IC404IC605
IC814
IC7201IC1902
IC1503
IC804IC813
IC812
IC811
IC810
SIDE B
MAIN UNITA
Q801
Q813
Q803
Q806
Q7202
Q7205
Q1502Q1503Q1504
Q7002
Q7010
IC407
Q408Q407
Q414Q415Q416Q420Q421Q428
A
A
B
C
D
1 2 3 4
1 2 3 4
66
PDP-R03E
B D
4.2 FRONT, LED and SR CONNECT UNITS
E
LED UNITE
SR CONNECT UNITD
FRONT UNITB
SIDE A
CN1F
P2503C
P2502C
CN8F P1301C
IC3401 Q3403 Q3402 Q3401
Q6001
Q6004Q6003
Q6002
Q6006
Q6005
A
B
C
D
1 2 3 4
1 2 3 4
67
PDP-R03E
AV UNITC
SIDE A
SC1504A
SC1503A
P3402B
P1703AP3001EP6001D
IC1401
IC1301
IC1102
IC1606IC1605IC1012
IC1602IC1611
IC1603IC1601IC1604IC1606
IC2504IC2501
IC1105
IC1103
IC1104
IC1615IC1614IC1609IC1613
IC2503
Q1101Q1406Q1405Q1407Q1103
Q1108
Q1102Q1125
Q1127
Q1130
Q1109
Q1106Q1107
Q1104Q1105
Q1105
Q1133
Q1124
Q1120
Q1106Q1107
Q1610Q1611
Q1609
Q1112
Q1109
Q1112
Q1113
Q1117
Q1131
Q1135
C
4.3 AV UNIT
A
B
C
D
1 2 3 4
1 2 3 4
68
PDP-R03E
PC I/F UNITF
SIDE A
P1702A P3401BSC1502A
SC1501A
P6000D
IC413
IC405
IC53IC418
IC400
IC25
IC1
IC319
IC320
IC4IC324
IC326
IC323
IC316IC327
IC411
IC8
IC7
IC310IC423
Q12
Q102
F
4.4 PC I/F UNIT
A
B
C
D
1 2 3 4
1 2 3 4
69
PDP-R03E
F
PC I/F UNITF
SIDE B
Q103
Q120
Q101
Q104
Q119
IC414
IC27IC28
IC321
IC404IC402
IC422
IC408
IC410IC328
IC415
IC421
IC420IC419IC407
IC322
IC19
IC2
IC3
A
B
C
D
1 2 3 4
1 2 3 4
70
PDP-R03E
EMC UNITH
POWER UNITG
SIDE A
LIVE
NEUTRAL
AC IN
P1502A
Q708Q709Q701Q703
Q704
Q702
IC701
IC702
IC703Q707
Q706Q705
4.5 POWER and EMC UNITS
G H
Mark No. Description Part No. Mark No. Description Part No.
71
PDP-R03E
Mark No. Description Part No. Mark No. Description Part No.
5. PCB PARTS LISTNOTES: • Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
• The mark found on some component parts indicates the importance of the safety factor of the part.Therefore, when replacing, be sure to use parts of identical designation.
• When ordering resistors, first convert resistance values into code form as shown in the following examples. Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%).
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).5.62k Ω → 562 × 101 → 5621 ...................................................... RN1/4PC 5 6 2 1 F
A
LIST OF ASSEMBLIESMAIN UNIT DUNTKA535FE01FRONT UNIT DUNTKA536DE01AV UNIT DUNTKA537DE01SR CONNECT UNIT DUNTKA594DE01LED UNIT DUNTKA649DE01PC I/F UNIT CPCI-0056CE11EMC UNIT RDENCA006WJZZPOWER UNIT RDENC0331CEZZ
• Using the system cable, connect the plasma display and the media receiver.• Connect the plasma display to the AC power source.• Connect the media receiver to the AC power source.
2. Procedure for turning ON the power
• Turn ON the AC power switch located on the plasma display.The power indicator on the plasma display will start blinking in red.(When the AC power switch on the media receiver is not ON, the power indicator on the plasma display alwaysblinks in red.)
• Turn ON the power switch located on the media receiver.The power indicator on the media receiver will be illuminated in green. Simultaneously, the power indicator onthe plasma display will change from blinking in red to illumination in green. Now the system has started up.
• If the power indicator on the media receiver is illuminated in red, press the 10 key located on the remote controllerand the STANDBY/ON button located on the plasma display. The power indicators on the plasma display andthe media receiver will change from red to green. Now the system has started up.
• Procedure for adjusting each part of media receiver
• The adjustments were made to the best settings at factory. If any setting deviates or if any readjustment isregarded as necessary when any part is replaced, perform the following steps.
• Any parameter that has been changed within the process adjustment is stored on the memory. If any readjustmentis required, write down the current value before changing it.
1. Preparation for adjustment
• Use a stable AC power source.• If the program is upgraded, it will take approximately 1 minute for the EEPROM to be initialized before any video
appears. Therefore, you will need to wait for this time period. Do not turn OFF the power or operate the systemduring the period.
• If the program is rewritten, write down the parameters that have been changed within the process adjustment(see “5.OSD menu and parameters displayed at manual adjustment), initialize the EEPROM, and then reenterthe recorded values.
2. Procedure for upgrading the software
(1) With the power being OFF, open the top cabinet for the media receiver and then set the slide switch from theNORMAL position to the WRITE position by inserting a needle-like insulator into the cutout located betweenthe WHITE port on the rear of the shield case for the I/F board and the RS-232C port.
(2) Connect the PC having the program installed, to the media receiver using the cross cable for the RS-232C port(for the details of the program, see Appendix).
(3) Open the MS-DOS window on the PC and then go to the directory in which the software is installed.(4) Start up the system to which the media receiver and plasma display have been connected.(5) Run “vup.bat at the MS-DOS prompt. The software will be upgraded.(6) Load the file “civic_XXXa.bhx/main.bhx/osd.bhx”. It will take approximately 7 minutes until the file has been
loaded. Never turn OFF the power or operate the system during this rewriting period.(7) After the file has been loaded, turn OFF the plasma display and the media receiver and then return the slide
switch in the above step 1 from the WRITE position to the NORMAL position. Now the software has beenupgraded.
97
PDP-R03E
3. Entering a special mode
1 Entering the process adjustment mode
[Steps]
(1) When using the remote controller:Using the system cable, properly connect the plasma display and the media receiver, and then turn ONthe power.After the system has started up, press the PROCESS ADJ button located on the remote controller.
(2) When using buttons on the main unit:Using the system cable, properly connect the plasma display and the media receiver.Turn ON the power while holding down the INPUT SELECT button and Vol UP button located the plasmadisplay.
[Description]
Various adjustments can be made manually.2 Entering the inspection process mode
[Steps]
After the system has started up, press the PROCESS ADJ button located on the remote controller.Set the parameter SIGNAL INFO to 1 on page 6 of the PROCESS ADJUSTMENT A MODE MENU.Subsequently, make the necessary adjustments in accordance with the above menu.
3 Procedure for setting up delivery
[Steps]
After the system has started up, press the DELIVERY SETUP button located on the remote controller.(Within the adjustment process, the channel settings remain unchanged. Once you exit the process adjustmentmode, the channel settings entered in the delivery adjustment mode become valid.)
[Description]
The user’s adjustment parameters and others will be set to the default values. The channel settings will alsobe initialized.
4. Exiting a special mode
(1) Process adjustment mode: Press the PROCESS ADJ button located on the remote controller or turn OFF thepower.
(2) Inspection process mode: Set the parameter SIGNAL INFO to 0 on page 6 of the PROCESS ADJ A MODEMENU or turn OFF the power.
(3) Delivery setup: After the delivery setup has been finished, the process adjustment mode is automaticallyselected. To exit the process adjustment mode, press the PROCESS ADJ button located on the remote controlleror turn OFF the power.
5. OSD menu and parameters displayed at manual adjustment
* The default values may slightly differ depending upon the program version to be rewritten.* The settings are not initialized to the default values by merely rewriting the program. (See the paragraph for
Preparation for adjustment.)(1) Descriptions of special buttons in process adjustment mode
Cursor UP key : Proceeds to the next page.Cursor DOWN key : Returns to the previous page.Vol UP key : Increases the adjusted value by 1.Vol DOWN key : Decreases the adjusted value by 1.Cursor LEFT key : Increases the adjusted value by 10.Cursor RIGHT key : Decreases the adjusted value by 10.Tuning UP key : Moves up the cursor.Tuning DOWN key : Moves down the cursor.
98
PDP-R03E
(2) Organization of process adjustment screen
This indicates that the process adjustment A mode is currently selected.↓A Process program version Input source Color system 1/6
CENTER VERSION 2001 06 21A ↑MONITOR VERSION XXXX Page
PANEL VERSION XXXX• •• •• •
2nd pageParameter displaye• +BAdj3.3V• +BAdj2.5V• PAL Y CONTRAST• PAL COLOR GAIN• MAIN CR GAIN PAL• MAIN SUBBRIGHT 15K• MAIN CONTRAST 15K• SUB PAL Y• SUB PAL COLOR GAIN• PEAK ACL SW
Description3.3 V adjustment2.2 V adjustmentPAL Y level adjustmentPAL color density adjustmentPAL Cr level adjustmentPedestal level adjustment (15 k)PCB input amplitude adjustment (15 k)Sub PAL Y level adjustmentSub PAL color density adjustment
3rd pageParameter displaye• SECAM Y CONTRAST• SECAM COLOR GAIN• MAIN CR GAIN SECAM• N358 Y CONTRAST• N358 COLOR GAIN• MAIN CR GAIN N358• N358 TINT• COMP 15K Y CONTRAST• COMP 15K COLOR GAIN• MAIN CR GAIN COMP15K• COMP HDTV SUB BRIGHT• COMP HDTV CONTRAST• DATA COPY
DescriptionSECAM Y level adjustmentSECAM color density level adjustmentSECAM Cr level adjustmentN358 Y level adjustmentN358 color density adjustmentN358 Cr level adjustmentN358 tone adjustmentCOMP 15 k Y level adjustmentCOMP 15 k color density adjustmentCOMP 15 k Cr level adjustmentCOMP HDTV black level adjustmentCOMP HDTV Y level adjustmentCOMP HDTV color density adjustment
The values for the above parameters should be written down before the EEPROM is replaced onthe media receiver.
99
PDP-R03E
6. Procedures before and after replacing the I/F board
1) Before replacing the I/F board, write down the values for the parameters listed on the 2nd and 3rd pages of theAdjustment Process A screen.If the values for the parameters cannot be written down because the I/F board is completely broken or for anyother reason, make all the adjustments in accordance with the paragraph for Adjustment procedure andparameters, rather than the following procedures. (End)Set the parameters listed on the 2nd and 3rd pages of the Adjustment Process A screen to the values you havewritten down.
7. Adjustment parameters
1) Analog adjustment
(1) Prior adjustment for AVC system chassis
(2) PAL signal adjustment
1 Destination check 1. Call the process adjustment mode.2. For the A2PZ50MP2E, check that the destination is
“Europe”.
Adjustment item Description Adjustment procedure
2 AVC center 3.3Vadjustment
Connect DC voltmeter to TP7008(Change TP No. to TP1702starting with 2nd lot).
Adjust output voltage of DC/DC 5 V line to3.3 ±0.02 V.Adjusted value: 3.3 ±0.02 V
3 AVC center 2.5Vadjustment
Connect DC voltmeter to TP7007(Change TP No. to TP1702starting with 2nd lot).
Adjust output voltage of DC/DC 2.5 V line to2.6 ±0.02 V.Adjusted value: 2.6 ±0.02 V
1 Setup 1. Set color system to “PAL”.2. Select PAL source.
Color bar signal including 100% white, such as splitfield color bar
Adjustment item Description Adjustment procedure
2 Tuner Y leveladjustment
1. Adjust TP1101 so that the Y signal without thechroma component should be 1.0 Vp-p (betweenthe bottom of sync signal and the white peak).Adjustment value: 1.00 ±0.05 V
3 MAIN PAL Y leveladjustment
1. Adjust TB1274_MAIN output (TP803) to 0.35 Vp-p.Adjusted value: 0.7 ±0.05 V
4 MAIN PAL colordensity adjustment
1. Adjust TB1274_MAIN output(TP802) to 0.35 Vp-p.Adjusted value:0.35 ±0.025 V
5 MAIN PAL Cr leveladjustment
1. Adjust TB1274_MAIN output(TP801) to 0.35 Vp-p.Adjusted value:0.35 ±0.05 V
6 MAIN CONTRASTadjustment
1. Turn off the PEAK ACL control. Adjust the output(TP815) of IC810 to have 1.1 Vp-p from thepedestal level.Adjusted value: 1.1 ±0.05 V
Press the 2-screen key. 1. Select the special 2-screen settings for adjustment(so that the same video source is reflected onMAIN/SUB).
7 SUB PAL Y leveladjustment
1. Adjust TB1274_SUB output (TP806) to 0.9 Vp-p.Adjusted value: 0.9 ±0.05 V
8 SUB PAL color densityadjustment
1. Adjust TB1274_SUB output (TP805) to 0.9 Vp-p.Adjusted value: 0.9 ±0.05 V
0.35V
0.35V
100
PDP-R03E
(3) SECAM signal adjustment
(4) N358 signal adjustment
1 Setup 1. Set color system to SECAM.2. Select SECAM source.
Color bar signal including 100% white, such as splitfield color bar
Adjustment item Description Adjustment procedure
2 MAIN SECAM Y leveladjustment
1. Adjust TB1274_MAIN output (TP803) to 0.7 Vp-p.Adjusted value: 0.7 ±0.05 V
3 MAIN SECAM colordensity adjustment
1. Adjust TB1274_MAIN output(TP802) to 0.35 Vp-p.Adjusted value:0.35 ±0.025 V
4 MAIN SECAM Cr leveladjustment
1. Adjust TB1274_MAIN output(TP801) to 0.35 Vp-p.Adjusted value:0.35 ±0.025 V
0.35V
0.35V
1 Setup 1. Set color system to N358.2. Select N358 source.
SMPTE color bar or similar color bar signalincluding 100% white.
Adjustment item Description Adjustment procedure
2 MAIN N368 Y leveladjustment
1. Adjust TB1274_MAIN output (TP803) to 0.7 Vp-p.Adjusted value: 0.7 ±0.05 V
3 MAIN N368 colordensity adjustment
1. Adjust TB1274_MAIN output(TP802) to 0.35 Vp-p.Adjusted value:0.35 ±0.025 V
4 MAIN N368 Cr leveladjustment
1. Adjust TB1274_MAIN output(TP801) to 0.35 Vp-p.Adjusted value:0.35 ±0.025 V
0.35V
0.35V
5 MAIN N368 hueadjustment
1. Adjust TB1274_MAIN output (TP802) so thatwaveform becomes as illustrated below:
Color bar signal including 100% white, like splitfield color bar
Adjustment item Description Adjustment procedure
2 MAIN componentHDTV contrastadjustment
Turn off the PEAK ACL control.Adjust the output (TP815) of IC810 (11) to have1.1 Vp-p from the pedestal level.Adjusted value: 1.1 ±0.05 V
1 Data Copy 1. Using the adjustment key, set “ON” in the DATACOPY line. Wait until “OFF” is displayed instead.Finally turn off the power to quit the processadjustment mode.
Adjustment item Description Adjustment procedure
1 Delivery setup Press the Delivery Setup button located on the remotecontroller, or position the cursor on the INDUSTRYINIT line, set the line to ON with the ADJ key, and thenpress the ENTER key. The adjustment is finishedwhen the line turns OFF,
Adjustment item Description Adjustment procedure
* Finally turn off the power to exit from the process adjustment mode.
102
PDP-R03EN
o s
ou
nd
No
soun
d fr
om s
peak
er
NO
YE
S
YE
SY
ES
Doe
s ou
tput
icon
den
ote
spea
ker
whe
n op
erat
ing
audi
o vo
lum
e co
ntro
l?
NO
NO
Doe
s ou
tput
icon
den
ote
lineo
ut w
hen
oper
atin
g au
dio
volu
me
cont
rol?
Mon
itor
outp
ut in
the
mai
n m
enu
is s
et
to "
Var
iabl
e". S
witc
h it
to "
Fix
ed".
YE
S
Is n
orm
al a
udio
out
put a
vaila
ble
at
each
rel
ated
pin
on
IC25
01
(MU
LTI S
OU
ND
PR
OC
ES
SO
R)?
IC25
01 P
ins
(36)
and
(37)
(SC
1 O
UT
L/R
)
YE
S
Che
ck Q
2505
and
250
4 (B
uffe
r) a
nd
perip
hera
l circ
uits
YE
S
Che
ck P
C I/
F U
nit a
nd p
erip
hera
l ci
rcui
ts.
No
audi
o ou
tput
(S
CA
RT
1)
YE
S
Is n
orm
al a
udio
out
put a
vaila
ble
at
each
rel
ated
pin
on
IC25
01
(MU
LTI S
OU
ND
PR
OC
ES
SO
R)?
IC25
01 P
ins
(27)
and
(28
) (D
AC
M L
/R)
YE
S
Che
ck th
e ci
rcui
t bet
wee
n IC
2501
Pin
s (2
7), (
28)
and
SC
AR
T1
Pin
s (3
), (
1),
as w
ell a
s au
dio
mut
e ci
rcui
t.
NO
Is n
orm
al tu
ner
audi
o in
put a
vaila
ble
at
each
rel
ated
pin
on
IC25
01
(MU
LTI S
OU
ND
PR
OC
ES
SO
R)?
IC25
01 P
in (
67)
(SO
UN
D IF
1)IC
2501
Pin
(69
) (S
OU
ND
IF2)
NO
NO
Is n
orm
al a
udio
out
put a
vaila
ble
at e
ach
rela
ted
pin
on IC
1301
(A
V S
WIT
CH
)?IC
1301
Pin
s (5
2) a
nd (
54)(
LOU
T1/
RO
UT
1)IC
1301
Pin
s (4
3) a
nd (
45)(
LOU
T2/
RO
UT
2)IC
1301
Pin
s (3
8) a
nd (
40)(
LOU
T3/
RO
UT
3)
NO
No
audi
o ou
tput
(S
CA
RT
2/3)
YE
S
Is n
orm
al a
udio
out
put a
vaila
ble
at
each
rel
ated
pin
on
IC25
01
(MU
LTI S
OU
ND
PR
OC
ES
SO
R)?
IC25
01 P
ins
(36)
and
(37
) (S
C1
OU
T L
/R)
YE
S
Che
ck th
e ci
rcui
t bet
wee
n IC
2501
Pin
s (3
6), (
37)
and
SC
AR
T2/
3 P
ins
(3),
(1)
, as
wel
l as
audi
o m
ute
circ
uit.
No
mon
itor
audi
o ou
tput
YE
S
Is n
orm
al a
udio
out
put a
vaila
ble
at
each
rel
ated
pin
on
IC25
01
(MU
LTI S
OU
ND
PR
OC
ES
SO
R)?
IC25
01 P
ins
(34)
and
(33
) (S
C2
OU
T L
/R)
YE
S
Che
ck th
e ci
rcui
t bet
wee
n IC
2501
Pin
s (3
4), (
33)
and
mon
itor
audi
o ou
tput
(J
1101
), a
s w
ell a
s au
dio
mut
e ci
rcui
t.
Che
ck th
e pl
asm
a di
spla
y se
ctio
n.
On
TV
rec
epti
on
On
ext
ern
al in
pu
t / P
C in
pu
t
Che
ck IC
2501
(M
ULT
I SO
UN
D P
RO
CE
SS
OR
) an
d pe
riphe
ral c
ircui
ts.
Che
ck B
.P.F
. of S
IF1
and
SIF
2 re
spec
tivel
y.
Che
ck T
U1
(U/V
tune
r) a
nd p
erip
hera
ls.
Is e
ach
audi
o in
put c
ircui
t nor
mal
on
IC13
01
(AV
SW
ITC
H)?
Bet
wee
n S
CA
RT1
Pin
s (6
), (2
) and
IC13
01 P
ins
(2),
(4)
Bet
wee
n S
CA
RT2
Pin
s (6
), (2
) and
IC13
01 P
ins
(9),
(11)
Bet
wee
n S
CA
RT3
Pin
s (6
), (2
) and
IC13
01 P
ins
(16)
, (18
)B
etw
een
front
inpu
t (J3
401)
and
IC13
01 P
ins
(23)
, (25
)B
etw
een
PC
inpu
t (J3
403)
and
IC13
01 P
ins
(29)
, (31
)
Che
ck IC
1301
(A
V S
WIT
CH
) an
d pe
riphe
rals
.
7. GENERAL INFORMATION7.1 DIAGNOSIS7.1.1 TROUBLE SHOOTING
103
PDP-R03E
No
Vid
eo O
utp
ut
(1)
YE
S
NO
YE
S
No
exte
rnal
inpu
t <S
CA
RT
1 A
V>
Che
ck th
e lin
e be
twee
n pi
n (2
0) o
f SC
AR
T1
and
pin
(3)
of IC
1301
.
YE
S
YE
S
No
exte
rnal
inpu
t <S
CA
RT
2 A
V>
Che
ck th
e lin
e be
twee
n pi
n (2
0) o
f SC
AR
T2
and
pin
(10)
of I
C13
01.
YE
S
NO
YE
S
No
exte
rnal
inpu
t <S
CA
RT
3 A
V>
NO
Che
ck IC
1301
(A
V
SW
ITC
H)
and
its
perip
hera
l circ
uits
.
Is th
ere
AV
sig
nal i
nput
at
pin
(17
) of
IC13
01 (
AV
S
WIT
CH
)?
Is th
ere
AV
sig
nal i
nput
at
pin
(10
) of
IC13
01 (
AV
S
WIT
CH
)?
Is th
ere
AV
sig
nal i
nput
at
pin
(3)
of I
C13
01 (
AV
S
WIT
CH
)?
YE
S
Are
ther
e R
, G a
nd B
MA
IN s
igna
l inp
uts
at p
ins
(5),
(7
) an
d (9
) of
IC81
1 (3
0MH
z L.
P.F.
), r
espe
ctiv
ely?
YE
S
NO
Che
ck IC
811
(30M
Hz
L.P.
F.)
and
its
perip
hera
l circ
uits
.
YE
S
YE
SY
ES
NO
Che
ck IC
810
(6.7
MH
z L.
P.F.
) an
d its
pe
riphe
ral c
ircui
ts.
Are
ther
e R,
G a
nd B
SUB
sig
nal
outp
uts
at p
ins
(13)
, (11
) and
(10)
of
IC81
0, re
spec
tivel
y? (i
n ST
D m
ode)
Are
ther
e R,
G a
nd B
SUB
sig
nal
outp
uts
at p
ins
(13)
, (11
) and
(10)
of
IC81
1, re
spec
tivel
y? (i
n HD
TV m
ode)
Che
ck th
e lin
e be
twee
n pi
n (2
0) o
f SC
AR
T3
and
pin
(17)
of I
C13
01.
YE
S
NO
Che
ck th
e lin
e be
twee
n IC
405
and
IC80
1.
YE
S
Are
ther
e M
AIN
-Y s
igna
l inp
uts
at p
ins
(1) a
nd (4
4) o
f IC
801
(MAI
N V
IDEO
CH
ROM
A) a
s w
ell a
s M
AIN
-C s
igna
l inp
uts
at p
ins
(43)
and
(48)
(com
posi
te s
igna
l at p
in (4
4) in
SEC
AM s
yste
m)?
NO
Che
ck th
e lin
e be
twee
n IC
402
and
IC80
2.
Are
ther
e SU
B-Y
sign
al in
put a
t pin
(44)
of I
C80
2 (S
UB
VID
EO C
HR
OM
A) a
t pin
(1) i
n N
TSC
sys
tem
) as
wel
l as
SUB-
C s
igna
l inp
ut a
t pin
(43)
at p
in (4
8) in
NTS
C s
yste
m)?
YE
S
NO
Che
ck IC
801
(MA
IN
VID
EO
CH
RO
MA
) an
d its
pe
riphe
ral c
ircui
ts.
YE
S
Are
ther
e Y,
Cb
and
Cr
MA
IN s
igna
l out
puts
at p
ins
(21)
, (22
) an
d (2
3) o
f IC
801,
res
pect
ivel
y?
NO
Che
ck IC
802
(SU
B
VID
EO
CH
RO
MA
) an
d its
per
iphe
ral c
ircui
ts.
Are
ther
e Y,
Cb
and
Cr
SU
B s
igna
l out
puts
at p
ins
(21)
, (22
) an
d (2
3) o
f IC
802,
res
pect
ivel
y?
YE
S
NO
Che
ck th
e lin
e be
twee
n IC
801
and
IC80
3.
YE
S
Are
ther
e Y,
Cb
and
Cr
MA
IN s
igna
l inp
uts
at p
ins
(69)
, (6
8) a
nd (
67)
of IC
803
(RG
B D
EC
OD
ER
), r
espe
ctiv
ely?
NO
Che
ck th
e lin
e be
twee
n IC
802
and
IC80
4.A
re th
ere
Y, C
b an
d C
r S
UB
sig
nal i
nput
s at
pin
s (5
),
(9)
and
(7)
of IC
804
(6.7
MH
z L.
P.F.
), r
espe
ctiv
ely?
YE
S
NO
Che
ck IC
803
(RG
B D
EC
OD
ER
) an
d its
pe
riphe
ral c
ircui
ts.
YE
S
YE
S
Are
ther
e R
, G a
nd B
MA
IN s
igna
l out
puts
at p
ins
(35)
, (37
) an
d (3
9) o
f IC
803,
res
pect
ivel
y?N
OC
heck
IC80
4 (6
.7M
Hz
L.P.
F.)
and
its p
erip
hera
l ci
rcui
ts.
Are
ther
e R
, G a
nd B
SU
B s
igna
l out
puts
at p
ins
(13)
, (11
) an
d (1
0) o
f IC
804,
res
pect
ivel
y?
NO
NO
NO
Sel
ect I
NP
UT
1 A
V o
n th
e m
enu
scre
en.
Sel
ect I
NP
UT
2 A
V o
n th
e m
enu
scre
en.
NO
Is IN
PU
T3
AV
sel
ecte
d on
the
Inpu
t Sel
ect
men
u sc
reen
?
Is IN
PU
T2
AV
sel
ecte
d on
the
Inpu
t Sel
ect
men
u sc
reen
?
Is IN
PU
T1
AV
sel
ecte
d on
the
Inpu
t Sel
ect
men
u sc
reen
?
Sel
ect I
NP
UT
3 A
V o
n th
e m
enu
scre
en.
Are
ther
e M
AIN
and
SU
B v
ideo
sig
nal o
utpu
ts a
t pin
s (5
6) a
nd (
44)
of IC
1301
, res
pect
ivel
y?
YE
SN
OC
heck
the
lines
bet
wee
n IC
1301
, IC
405
and
IC40
2.
Are
ther
e vi
deo
sign
al in
puts
at p
ins
(1)
and
(2)
of IC
405
(MA
IN C
OM
B F
ILT
ER
) an
d IC
402
(SU
B C
OM
B F
ILT
ER
)?
Che
ck th
e P
C I/
F u
nit.
<M
AIN
sys
tem
><
SU
B s
yste
m>
<H
DT
V m
ode>
<S
TD
mod
e>
Are
ther
e R
, G a
nd B
MA
IN s
igna
l inp
uts
at p
ins
(5),
(7
) an
d (9
) of
IC81
0 (6
.7M
Hz
L.P.
F.),
res
pect
ivel
y?
C A D F
B E
104
PDP-R03EN
o p
ictu
re (
2)
NO
YE
S
NO
YE
S
No
exte
rnal
inpu
t pic
ture
(S
CA
RT
2 Y
/C)
Is IN
PU
T2 Y
/C s
elec
ted
on
Inpu
t/Sel
ect m
enu
scre
en?
Sel
ect I
NP
UT
2 Y
/C o
n m
enu
sele
ctio
n sc
reen
.
Is Y
sig
nal i
nput
ava
ilabl
e at
P
in (
10)
and
C s
igna
l inp
ut
at P
in (
12)
resp
ectiv
ely
on
IC13
01 (
AV S
WIT
CH
)?
Che
ck th
e ci
rcui
t bet
wee
n S
CA
RT
2 P
ins
(20)
, (15
) an
d IC
1301
Pin
s (1
0), (
12).
NO
YE
S
NO
YE
S
NO
No
exte
rnal
inpu
t pic
ture
(S
CA
RT
3 Y
/C)
Is IN
PU
T3 Y
/C s
elec
ted
on
Inpu
t/Sel
ect m
enu
scre
en?
Sel
ect I
NP
UT
3 Y
/C o
n m
enu
sele
ctio
n sc
reen
.
Is Y
sig
nal i
nput
ava
ilabl
e at
P
in (
17)
and
C s
igna
l inp
ut
at P
in (
19)
resp
ectiv
ely
on
IC13
01 (
AV S
WIT
CH
)?
Che
ck th
e ci
rcui
t bet
wee
n S
CA
RT
3 P
ins
(20)
, (15
) an
d IC
1301
Pin
s (1
7), (
19).
Che
ck IC
1301
(A
V
SW
ITC
H)
and
perip
hera
l circ
uits
.
YE
S
YE
S
NO
YE
S
No
TV
pic
ture
Is v
ideo
out
put a
vaila
ble
at
Pin
23
of T
U1
(U/V
tune
r)?
Che
ck T
U1
(U/V
tune
r)
and
perip
hera
ls.
Is v
ideo
inpu
t sig
nal
avai
labl
e at
Pin
(63
) on
IC
1301
(A
V S
WIT
CH
)?
Che
ck th
e ci
rcui
t be
twee
n T
UN
ER
Pin
(23
) an
d IC
1301
Pin
(63
).
No
pic
ture
(3)
NO
YE
S
NO
YE
S
No
exte
rnal
inpu
t pic
ture
(S
CA
RT
1 R
GB
)
Is IN
PU
T1
RG
B s
elec
ted
on In
put/S
elec
t men
u sc
reen
?
Sel
ect I
NP
UT
1 R
GB
on
men
u se
lect
ion
scre
en.
Is R
GB
sig
nal i
nput
av
aila
ble
at P
ins
(59)
, (6
1) a
nd (
63)
on IC
1401
(A
V S
WIT
CH
)?
Che
ck th
e ci
rcui
t bet
wee
n S
CA
RT
1 P
ins
(15)
, (11
),
(7)
and
IC14
01 P
ins
(59)
, (6
1), (
63).
NO
YE
S
NO
YE
S
No
exte
rnal
inpu
t pic
ture
(S
CA
RT
3 R
GB
)
Is IN
PU
T3
RG
B s
elec
ted
on In
put/S
elec
t men
u sc
reen
?
Sel
ect I
NP
UT
3 R
GB
on
men
u se
lect
ion
scre
en.
Is R
GB
sig
nal i
nput
av
aila
ble
at P
ins
(5),
(7)
an
d (9
) on
IC14
01 (
AV
S
WIT
CH
)?
Che
ck th
e ci
rcui
t be
twee
n S
CA
RT
3 P
ins
(15)
, (11
), (
7) a
nd
IC14
01 P
ins
(5),
(7)
, (9)
.
NO
YE
S
NO
YE
S
No
com
pone
nt p
ictu
re
Is IN
PU
T3
CO
MP
ON
EN
T
sele
cted
on
Inpu
t/Sel
ect
men
u sc
reen
?
Sel
ect I
NP
UT
3 C
OM
PO
NE
NT
on
men
u se
lect
ion
scre
en.
Is c
ompo
nent
sig
nal i
nput
av
aila
ble
at P
ins
(15)
, (17
) an
d (1
9) o
n IC
1401
(A
V
SW
ITC
H)?
Che
ck th
e ci
rcui
t bet
wee
n co
mpo
nent
sig
nal i
nput
te
rmin
al (J
1101
) and
IC14
01
Pin
s (1
5), (
17) a
nd (1
9).
NO
YE
S
Is R
GB
sig
nal o
utpu
t av
aila
ble
at P
ins
(50)
, (48
) an
d (4
6) o
n IC
1401
?
Che
ck IC
1401
(A
V
SW
ITC
H)
and
perip
hera
l ci
rcui
ts.
NO
YE
S
Is R
GB
sig
nal o
utpu
t av
aila
ble
at P
ins
(44)
, (42
) an
d (4
0) o
n IC
1401
?
Che
ck IC
1401
(A
V
SW
ITC
H)
and
perip
hera
l ci
rcui
ts.
NO
YE
S
YE
SY
ES
YE
S
Is c
ompo
nent
sig
nal o
utpu
t av
aila
ble
at P
ins
(38)
, (36
) an
d (3
4) o
n IC
1401
?
Che
ck IC
1401
(A
V
SW
ITC
H)
and
perip
hera
l ci
rcui
ts.
NO
Is R
GB
sig
nal i
nput
ava
ilabl
e at
Pin
s (2
7), (
26)
and
(25)
re
spec
tivel
y on
IC80
1 (M
AIN
VID
EO
CH
RO
MA
)?
Che
ck th
e ci
rcui
t bet
wee
n IC
1401
Pin
s (5
0), (
48),
(4
6) a
nd IC
801
Pin
s (2
7),
(26)
, (25
).
NO
Is R
GB
sig
nal i
nput
ava
ilabl
e at
P
ins
(27)
, (35
), (2
6), (
34),
(25)
an
d (3
3) re
spec
tivel
y on
IC80
2 (S
UB
VID
EO
CH
RO
MA
)?
Che
ck th
e ci
rcui
t bet
wee
n IC
1401
Pin
s (4
4), (
42),
(40
) an
d IC
802
Pin
s (2
7), (
35),
(2
6), (
34),
(25
) an
d (3
3).
NO
Is c
ompo
nent
sig
nal i
nput
av
aila
ble
at P
ins
(3),
(4)
an
d (5
) re
spec
tivel
y on
IC
803
(RG
B D
EC
OD
ER
)?
Che
ck th
e ci
rcui
t bet
wee
n IC
1401
Pin
s (3
8), (
36),
(3
4) a
nd IC
803
Pin
s (3
),
(4)
and
(5).
CA B
Is M
AIN
-Y s
igna
l out
put a
vaila
ble
at P
in (5
6) a
nd M
AIN
-C s
igna
l out
put a
t Pin
(58)
resp
ectiv
ely
on IC
1301
?
Is S
UB
-Y s
igna
l out
put a
vaila
ble
at P
in (4
4) a
nd S
UB
-C s
igna
l out
put a
t Pin
(47)
resp
ectiv
ely
on IC
1301
?
DE
F
105
PDP-R03E
No
pic
ture
(4)
NO
YE
S
Is IN
PU
T4
sele
cted
in In
put
Sou
rce?
Sel
ect I
NP
UT
4 in
Inpu
t Sou
rce.
NO
YE
S
Is IN
PU
T4
sele
cted
in In
put
Sou
rce?
Sel
ect I
NP
UT
4 in
Inpu
t Sou
rce.
NO
YE
S
Is v
ideo
sig
nal
inpu
t ava
ilabl
e at
P
in (2
2) o
n IC
1301
(A
V S
WIT
CH
)?
Che
ck th
e ci
rcui
t be
twee
n fro
nt
INP
UT4
(J34
01)
AV te
rmin
al a
nd
Pin
(22)
on
IC13
01.
NO
YE
S
Is Y
sig
nal i
nput
av
aila
ble
at P
in (2
4)
and
C s
igna
l inp
ut a
t Pi
n (2
6) re
spec
tivel
y on
IC13
01 (A
V SW
ITC
H)?
Chec
k th
e cir
cuit
betw
een
front
IN
PUT4
(J34
01) S
te
rmin
al P
ins
(2),
(1)
and
Pins
(24)
, (26
) on
IC13
01.
NO
Is M
AIN
-Y s
igna
l out
put
avai
labl
e at
Pin
(56)
and
M
AIN
-C s
igna
l out
put a
t P
in (5
8) re
spec
tivel
y on
IC
1301
?
Is S
UB
-Y s
igna
l out
put
avai
labl
e at
Pin
(44)
and
S
UB
-C s
igna
l out
put a
t P
in (4
7) re
spec
tivel
y on
IC
1301
?
Che
ck IC
1301
(A
V S
WIT
CH
) an
d pe
riphe
ral
circ
uits
.
Syn
chro
niz
atio
n f
ailu
re
NO
YE
S
Is V
DM
/HD
M o
utpu
t av
aila
ble
at P
ins
(28)
an
d (2
9) o
n IC
803
(RG
B D
EC
OD
ER
)?
Che
ck IC
803
(RG
B
DE
CO
DE
R)
and
perip
hera
l circ
uits
.
NO
NO
YE
S
Is H
I/VI i
nput
av
aila
ble
at P
ins
(66)
an
d (6
5) o
n IC
803
(RG
B D
EC
OD
ER
)?
Che
ck th
e ci
rcui
t be
twee
n IC
1901
Pin
s (3
4), (
35)
and
IC80
3 P
ins
(66)
, (65
).
NO
YE
S
Is P
L H
D/V
D o
utpu
t av
aila
ble
at P
ins
(34)
and
(3
5) o
n IC
1901
(PLD
)?
Che
ck IC
1901
(P
LD)
and
perip
hera
l circ
uits
.
YE
S
MA
IN: I
s H
D1/
VD
1 in
put a
vaila
ble
at P
ins
(44)
and
(2) o
n IC
1901
(PLD
)?S
UB
: Is
HD
2/V
D2
inpu
t ava
ilabl
e at
Pin
s (1
9) a
nd (2
0) o
n IC
1901
(PLD
)?C
OM
PO
NE
NT:
Is S
P H
D/V
D in
put a
vaila
ble
at P
ins
(40)
and
(5) o
n IC
1901
(PLD
)?
NO
Is H
D1/
VD
1 ou
tput
ava
ilabl
e at
Pin
s (9
) an
d (4
) on
IC80
1 (M
AIN
VID
EO
CH
RO
MA
)?
Che
ck IC
801
(MAI
N V
IDEO
C
HR
OM
A) a
nd p
erip
hera
l circ
uits
.
YE
S
NO
Is S
P H
D/V
D o
utpu
t av
aila
ble
at P
ins
(16)
and
(2
8) o
n IC
604
(SY
NC
SE
P)?
Che
ck IC
604
(SY
NC
SE
P) a
nd
perip
hera
l circ
uits
.
YE
S
NO
Is H
D2M
/VD
2 ou
tput
ava
ilabl
e at
Pin
s (9
) and
(4) o
n IC
802
(SU
B V
IDE
O C
HR
OM
A)?
YE
S
Is v
ideo
sig
nal i
nput
av
aila
ble
at P
in (
21)
on
IC16
01 (
TE
LET
EX
T C
PU
)?
Is T
ELE
TE
XT
com
patib
le b
road
cast
rec
eive
d (o
r ar
e si
gnal
s fr
om o
ther
TE
LET
EX
T c
ompa
tible
eq
uipm
ent r
ecei
ved
at v
ideo
inpu
t ter
min
al),
and
is T
ELE
TE
XT
sel
ecte
d on
rem
ote
cont
rolle
r?
Che
ck th
e ci
rcui
t bet
wee
n IC
1301
Pin
(56
) an
d IC
1601
P
in (
2).
NO
YE
S
Is s
igna
l inp
ut a
vaila
ble
at P
ins
(57)
, (58
) and
(59)
on
IC16
01?
Che
ck IC
1601
(TE
LETE
XT
CP
U) a
nd p
erip
her
al
NO
Is s
igna
l inp
ut a
vaila
ble
at
Pin
s 57
, 53
and
55 o
n IC
1301
(A
V S
WIT
CH
)?
Che
ck th
e ci
rcui
t bet
wee
n IC
1601
P
ins
(57)
, (58
) and
(59)
and
C
1301
Pin
s (5
7), (
53) a
nd (5
5).
YE
SN
O
Sel
ect T
ELE
TE
XT
in
acco
rdan
ce w
ith th
e sp
ecifi
ed p
roce
dure
.
Che
ck IC
802
(SU
B VI
DEO
C
HR
OM
A) a
nd p
erip
hera
l circ
uits
.
No
TE
LE
TE
XT
scr
een
NO
YE
S
Is H
DS
/VD
S o
utpu
t av
aila
ble
at P
ins
(21)
and
(22
) on
IC
1901
(P
LD)?
Che
ck IC
1901
(P
LD)
and
perip
hera
l ci
rcui
ts.
NO
No
exte
rnal
inpu
t pic
ture
(IN
PU
T4
AV
)N
o ex
tern
al in
put p
ictu
re (
INP
UT
4 S
-IN
)
No
pic
ture
(5)
NO
Is v
ideo
sig
nal
outp
ut a
vaila
ble
at
Pin
(41)
on
IC13
01
(AV
SW
ITC
H)?
Che
ck IC
1301
(A
V S
WIT
CH
) an
d pe
riphe
ral
circ
uits
.
NO
Is Y
sig
nal o
utpu
t av
aila
ble
at P
in
(39)
and
C s
igna
l ou
tput
at P
in (3
7)
resp
ectiv
ely
on
IC13
01 (A
V
SW
ITC
H)?
YE
S
YE
S
YE
S
Che
ck th
e ci
rcui
t be
twee
n IC
1401
P
in (
41)
and
SC
AR
T1
mon
itor
vide
o ou
tput
te
rmin
al (
J110
1).
Che
ck th
e ci
rcui
t be
twee
n IC
1301
P
ins
(39)
, (37
) and
m
onito
r S-O
UT
term
inal
Pin
s 3/
4.
Con
firm
inpu
t si
gnal
is S
-IN
PU
T.
No
mon
itor
pict
ure
(AV
)N
o m
onito
r pi
ctur
e (S
-OU
T)
Che
ck IC
1301
(A
V S
WIT
CH
) an
d pe
riphe
ral
circ
uits
.
MA
INS
UB
Che
ck th
e ci
rcui
t bet
wee
n IC
802
Pin
s (9
),
(4)
and
IC19
01
Pin
s (1
9), (
20).
C
A B
106
PDP-R03EN
o p
ictu
re
NO
YE
S
No
TV,
vid
eo a
nd c
ompo
nent
pic
ture
Is n
orm
al in
put a
vaila
ble
at P
ins
(124
), (
133)
and
(1
39)
on IC
4?
Che
ck C
N6
and
perip
hera
ls.
NO
YE
S
Are
TL2
07, T
L208
and
T
L211
nor
mal
?C
heck
CN
6 an
d pe
riphe
rals
.
NO
YE
S
Is d
igita
l out
put s
ectio
n no
rmal
on
IC4?
Che
ck IC
4 an
d pe
riphe
rals
.
NO
YE
S
Is d
igita
l out
put s
ectio
n no
rmal
on
IC31
0?C
heck
IC31
0 an
d pe
riphe
rals
.
NO
YE
S
Is d
igita
l out
put o
f IC
25
norm
al?
Che
ck IC
25 a
nd
perip
hera
ls.
No
PC
pic
ture
YE
S
Is s
igna
l ava
ilabl
e at
Pin
s (2
1), (
22),
(24
), (
25),
(27
), (
28),
(30
) an
d (3
1) o
n IC
413?
(T
he s
igna
l is
of h
igh
freq
uenc
y (a
littl
e le
ss th
an 1
GH
z).
Pay
due
atte
ntio
n to
it d
urin
g ob
serv
atio
n.)
Mon
itor
prob
lem
is li
kely
.
NO
PC
I/F
Uni
t (C
PC
i-00
56C
E)
inte
rnal
pro
blem
is
like
ly.
No
MA
IN p
ictu
re o
n si
ngle
scr
een
and
dual
scr
een.
No
SU
B p
ictu
re o
n du
al s
cree
nN
O
YE
S
Is n
orm
al in
put a
vaila
ble
at P
ins
(126
), (
136)
and
(1
41)
on IC
4?
Che
ck C
N8
and
perip
hera
ls.
NO
YE
S
Is d
igita
l out
put s
ectio
n no
rmal
on
IC4?
Che
ck IC
4 an
d pe
riphe
rals
.
NO
YE
S
Is d
igita
l out
put o
f IC
25
norm
al?
Che
ck IC
25 a
nd
perip
hera
ls.
107
PDP-R03E
MAIN Unit
AV Unit
FRONT Unit
POWER Unit
LED Unit
SR CONNECT Unit
PC I/F Unit
EMC Unit
Bottom cabinet
17
Top cabinet
6-2
8-1
6-19-16-3
6-56-4
8-2
9-2
10
6-7
5
2
3
2 3
3
6-6
4
A
G
B
F
HD
E
C
7.1.2 DISASSEMBLY1. Remove the six lock screws from the back of the top cabinet. Slide the top cabinet backward and detach it.2. Remove the three lock screws from the front panel. Undo the three hooks at the top and the four hooks at the
bottom, and detach the front panel.3. Remove the two hexagonal shafts from the front shield. Undo the two hooks on both sides and detach the
front shield.4. Remove the three lock screws from the front unit and detach this unit.5. Remove the one lock screw from the LED unit and detach this unit.6. Remove the PC I/F unit and SR connect unit assemblies.
6-1. Remove the two hexagonal shafts each from the system cable (white) terminal and the RS-232C terminal,both on the PC I/F unit.
6-2. Remove the two lock nuts from the control terminal on the SR connect unit, and the two lock screws fromthe system cable (gray) terminal also on the SR connect unit.
6-3. Remove the two lock screws from the PC I/F unit bracket.6-4. Remove the four lock screws from the PC I/F unit and SR connect unit assemblies. Take out these
assemblies.6-5. Remove the three lock screws from the brackets of the PC I/F unit and SR connect unit assemblies.
Detach the shield.6-6. Remove the six lock screws from the PC I/F unit. Detach this unit from the bracket.6-7. Remove the two lock screws from the SR connect unit. Detach this unit from the bracket.
7. Remove the seven lock screws from the main unit and detach this unit.8. Remove the AV unit.
8-1. Remove the six lock screws from the AV unit.8-2. Remove the six lock screws from the AV unit and detach this unit.
9. Remove the EMC unit assemblies.9-1. Remove the two lock screws from the EMC unit bracket.9-2. Remove the two lock screws from the EMC unit and detach this unit.
10. Remove the three lock screws from the power unit and detach this unit.
• Description of Functions of Main ICs on PC I/F Unit• IC4 (CXA3506R)
This IC is an A/D converter that incorporates a 3-channel, 8-bit, 120 MSPS amplifier and PLL. It is used for thevideo signals input to the I/F board on the main channel in the 1-screen and 2-screen modes, and also for thevideo signals input from the front for the PC.The video signals (analog RGB) from the CN6 are input to IN1 of IC4.For the PC, the video signals (analog RGB) from CN8 are input to IN2 of IC4.The input video signals are converted into digital signals and then sent to IC25.
• IC310 (TLC5733A)This IC is a 3-channel, 8-bit, 20 MSPS A/D converter.It is used for the sub-channel of the video signals input to the I/F board in the 2-screen mode.The video signals (analog YCbCr) from CN6 are input to IC310.The video signals input to this IC are converted into digital signals and then sent to IC25.
• IC25 (IX3434CE)This IC performs the I/P conversion and scaling to match the digitalized video with the output resolution, and alsothe data conversion.It has two input lines, V0 and V1. The V0 line is used to process the RGB, composite, and skirt signals input to the480i and 580i components for the sub-channel in the 2-screen mode. The V1 line is used to process all the signalsas well as V1 for the main channel in the 1-screen and 2-screen modes.The IC25 detects what resolution is input from the input synchronizing signal; creates H synchronization inaccordance with the frequency division ratio; creates the clamp signal in accordance with the input synchronizingsignal; and performs the data matrix conversion.The video signals input to this IC is sent to IC413.
• IC413 (SiI168)This IC is a panel link transmitter.It converts the 8-bit RGB video data output from IC25 into the differential TMDS signals and then digitally transmitsthe converted signals to the monitor.The TMDS signals are transmitted at the frequency 10 times higher than the clock frequency.
• IC1 (IX3270CE)This IC is a 1-chip RISC microprocessor.It performs communication with the monitor and operates the system.The IC1 also controls each IC in the media receiver and partially manages the power source.
• IC405 (uPD4721)This IC is an RS-232 line driver receiver conforming to the EIA/TIA-232-E standard.The IC405, when connected to a PC, allows for externally controlling the system.It is also applicable for upgrading IC1.
109
PDP-R03E
• Description of Main ICs on Company P’s PDP Destined for Europe• IC1301 (CXA2069Q)
This IC is a 7-input, 3-output selector.The video signals other than those for the PC and components, which have been input from each input connectorand the tuner, and all the audio signals are sent to the IC1301 and then selected.Output 1 is used internally and output 3 in the monitor output.When the S video input is output to the monitor, Y and C signals are mixed in this IC.The video signals sent to the IC1301 are then input to the YC separation circuits, IC405 (main) and IC402 (sub).The audio signals are input to the I/F board via IC2501 (sound processor).
• IC1401 (MM1519XQ)This IC is a 4-input, 8-output video selector for component input.The AV3 component input, AV1, RGB input, and Teletext RGB signals are input to the IC1401. The output signalsgo to the main, sub, and component channels.
• IC1601 (SDA5550M).This IC is a microcomputer for Teletext.Video signals are input to the IC1601, which then decodes the Teletex data and outputs it as RGB data.
• IC2501 (IX3371CE)This IC is used to decode audio signals.It serves as both the S IF decoder and the selector for the input audio data.
• IC801/IC802 (TB1274AF)This IC synchronizes video and chroma signals for PAL/NTSC/SECAM color televisions.Its video circuit includes a high-performance image quality compensation circuit and its chroma circuit a PAL/NTSC/SECAM automatic selection circuit. The M/N-PAL clock signals at 4.43 and 8.58 MHz are internally generatedfor color demodulation.The PAL/SECAM demodulation circuit uses a base band signal processing system with built-in IH DL and istherefore adjustment-free.The IC801/IC802 has 4 lines for YC signal input, 2 lines for RGB signal input, and 2 lines for color difference signalinput. It receives color different signals for the main and sub channels from IC405 (main), IC402 (sub), andIC1401 in the former stage, and provides 1 line for color difference signal output.
• IC803 (CXA2101Q)This IC consists of a base band signal processing section for color different input, an RGB signal processingsection, and a 4-line video switch (including HV synchronizing signal processing).Input selection is performed by INPUT-SEL (HC BUS). YcbCx, HD YphPr, GBR and their respective HV synchronizingsignals are input to each line.As the multi-scanning compliance range, a horizontal scanning frequency of 15~60 kHz can be input.
• IC1901 (IX3566CE)This IC is FPGA for the synchronizing system.It creates sand castle pulses for IC803 and generates horizontal blanking signals.
• IC604 (TA1318N)This IC synchronizes TV component signals.The IC804 incorporates the necessary functions for measuring the frequency of input signals and synchronousreplay into a single chip, and is applicable for horizontal synchronous replay (15.75, 31.5, 33.75, and 45 kHz) andvertical synchronous replay (525I, 525P, 625I, 750P, 1125I, 1125P, PAL 100 Hz, and NTSC 120 Hz).
• IC405/IC402 (CXD2064Q)This IC is a comb filter in the applicable field for both the NTSC and PAL systems. It performs the Y/C separationof the main and sub channel video signals that have been output from IC1801.
• IC407/IC404 (ML6428C1)This IC is a 6.7 MHz low-pass filter.
• IC810/IC804 (IX3473CE)This IC is a 6.7 MHz low-pass filter incorporating a 6 dB amplifier.
• IC811 (IX3474CE)This IC is a 80 MHz low-pass filter incorporating a 6 dB amplifier.
110
PDP-R03E
MONITOR OUTPUTS-VIDEO VIDEO R–AUDIO–L
(GRAY)RS-232C
IN OUTCONTROL
INPUT 3
INPUT 2
Y PB PR
COMPONENT
AC INLET
SYSTEMCABLE (WHITE)
INPUT 1
POWER
STANDBY/ON
MEDIA RECEIVER PDP-R03E
Front view
INPUT 1 terminal(SCART)
INPUT 3 terminals (Y, PB, PR)
INPUT 2 terminal(SCART)
MONITOR OUTPUTterminal (S-VIDEO)
SYSTEM CABLE terminal(GRAY)
SYSTEM CABLE terminal(WHITE)
AC INPUT terminal
CLEAR button*
POWER button
RS-232C terminal(used in the factory setup)
INPUT 4 terminal (S-VIDEO)
INPUT 4 terminal (VIDEO)
PC INPUT terminal (AUDIO) INPUT 4 terminals (AUDIO)
INPUT 3 terminal (SCART)
MONITOR OUTPUTterminal (VIDEO)
MONITOR OUTPUTterminals (AUDIO)
PC INPUT terminal (ANALOG RGB)
CONTROL terminal
Media Receiver
If you’re having problems operating the Media Receiver and want to return to normal screen, even when it stayson (the indicator lights green), press CLEAR on the Media Receiver. Pressing CLEAR resets the System as shown below.• AV SELECTION resets to STANDARD• TV channel resets to channel 1• Multiscreen resets to normal• Audio setting initialises• SRS resets to Off.• Image position is initialises
NOTE• Pressing CLEAR will not work if the System is in standby mode but the indicator lights red.• Pressing CLEAR will not delete channel preset or password. See initialising factory preset settings when you know your password. See initialising factory preset values when you have forgotten your password.
Rear view
Antenna input terminal
8. PANEL FACILITIES AND SPECIFICATIONS8.1 PANEL FACILITIES
111
PDP-R03E
112
PDP-R03E
8.2 SPECIFICATIONSItem Media Receiver, Model:PDP-R03E
Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TVFunction
B/G, D/K, I, L/L’
VHF/UHF E2–E69ch, F2–F10ch, I21–I69ch, IR A–IR Jch
CATV Hyper-band, S1–S41ch
Auto Channel Preset 99 ch, Auto Preset, Auto Label, Auto Sort
STEREO NICAM/A2
Terminals SCART (AV in, RGB in, TV out)
INPUT 2 SCART (AV in/out, S-VIDEO in, AV Link)
INPUT 3 SCART (AV in/out, S-VIDEO in, RGB in), Component
Antenna 75Ω Din Type for VHF/UHF in
INPUT 4 S-VIDEO, AV in
PC 15 Pin mini D-Sub, Audio in
Monitor Out Terminal Audio (Variable, Fixed), S-VIDEO out, AV out
Power Requirement AC 220–240 V, 50/60 Hz, 40 W (0.8 W Standby)
Dimensions 420 (W), 70 (H), 330 (D) mm
Weight 4.4 kg
Accessories Power Cord, Remote control unit, Two AA size batteries, System Cable,Two Operating Instructions
Receiving System
Tuner
Rear INPUT 1
Front
Rear
• Design and specifications are subject to change without notice.
Power cord (QACCBA005WJZZ, QACCVA002WJZZ)
(For Europe, except U.K. and Eire) (For U.K., and Eire) Remote control unit (RRMCG1677CESA)
Two AA size batteries(Alkaline battery) System cable
