Pipe Fittings & Valves - Bob Dean ... Fittings & Valves Manufacturers & Vendors American Anvil...

��

www.bobdeansupply.comPipe Fittings & ValvesManufacturers & Vendors

AmericanAnvilDezurikDixonMilwaukeeSharpeSimmonsTubelineWebstone

Malleable Iron Fittings................124Steel Fittings .............................. 130Butt Weld Fittings ......................131Ball Valves .................................. 135Gate Valves ................................ 137

PipeFittings

Anvil Class 150 (standard weight) Malleable Iron Fittings conform to ASME B16.3 and Unions conform to ASME B16.39. All elbows and tees 3/8” and larger are 100% gas tested at a minimum of 100 PSI. Class 300 fittings conform to ASME B16.3 and are in compliance with the ARR.

Malleable Iron Threaded Pipe Fittings

Fort Myers Branch Clewiston Branch2624 Hanson Street 1310 Evercane RoadFort Myers, FL 33901 Clewiston, FL 33440(800) 282-8378 (800) 282-5186(239) 332-1131 (863) 983-6131(239) 332-7746 Fax (863) 983-9775 [email protected] [email protected]

Check item availability and make secure online purchases with Bob Dean Supply’s eCatalog at

www.bobdeansupply.com

1-800-282-8378

��

MalleableIron Fittings

• 90° Elbow.• Figure 1101.• Malleable Iron Class 150 (Standard)

Black Galvanized

Size A Weight Part No. Weight Part No.

1/8” NPS 11/16” 0.06 lbs R1895 0.07 lbs R06021/4” 13/16” 0.11 R1900 0.12 R06043/8” 15/16” 0.17 R1901 0.17 R06061/2” 1-1/8” 0.26 R1902 0.27 R06083/4” 1-5/16” 0.38 R1904 0.43 R0610

1” 1-1/2” 0.63 R1906 0.65 R06121-1/4” 1-3/4” 0.96 R1908 0.94 R06141-1/2” 1-15/16” 1.3 R1910 1.3 R0616

2” 2-1/4” 2.1 R1912 2.0 R06182-1/2” 2-11/16” 3.5 R1914 3.6 R0620

3” 3-1/16” 5.2 R1916 5.3 R06223-1/2” 3-7/16” 7.1 R1917 7.2 R0624

4” 3-13/16” 8.9 R1918 9.4 R06265” 4-1/2” 14 R1920 15 R06286” 5-1/8” 23 R1923 24 R0630

• 45° Elbow• Figure 1102.• Malleable Iron Class 150 (Standard)

Black Galvanized

Size A Weight Part No. Weight Part No.

1/8” NPS 11/16” 0.06 lbs - 0.08 lbs R05021/4” 3/4” 0.11 R1800 0.11 R05043/8” 13/16” 0.16 R1801 0.18 R05061/2” 7/8” 0.21 R1802 0.24 R05083/4” 1” 0.37 R1804 0.39 R0510

1” 1-1/8” 0.54 R1806 0.57 R05121-1/4” 1-5/16” 0.86 R1808 0.87 R05141-1/2” 1-7/16” 1.1 R1810 1.2 R0516

2” 1-11/16” 1.7 R1812 1.9 R05182-1/2” 1-15/16” 2.8 R1813 2.9 R0519

3” 2-3/16” 4.5 R1814 4.6 R05214” 2-5/8” 7.2 R1816 7.3 R05235” 3-1/16” 11 R1818 12 -6” 3-7/16” 17 R1820 18 R0525

• 45° Street Elbow.• Figure 1104• Malleable Iron Class 150 (Standard)

Black Galvanized

Size C K Weight Part No. Weight Part No.

1/8” NPS 11/16” 7/8” 0.06 lbs - 0.07 lbs R07031/4” 3/4” 15/16” 0.10 R2105 0.11 R07053/8” 13/16” 1” 0.14 R1750 0.14 R07071/2” 7/8” 1-1/8” 0.20 R1803 0.21 R07093/4” 1” 1-5/16” 0.33 R2103 0.34 R0711

1” 1-1/8” 1-7/16” 0.52 R2109 0.53 R07131-1/4” 1-5/16” 1-11/16” 0.84 R2113 0.87 R07151-1/2” 1-7/16” 1-7/8” 1.2 R2111 1.3 R0717

2” 1-11/16” 2-1/4” 1.9 R2115 2.0 R0719

• Straight Tee• Figure 1105• Malleable Iron Class 150 (Standard)

Black Galvanized

NPS A Weight Part No. Weight Part No.

1/8” 11/16” 0.09 lbs R2299 0.10 lbs R10021/4” 13/16” 0.15 R2300 0.16 R10043/8” 15/16” 0.23 R2301 0.24 R10061/2” 1-1/8” 0.36 R2302 0.37 R10083/4” 1-5/16” 0.56 R2304 0.58 R1010

1” 1-1/2” 0.90 R2306 0.92 R10121-1/4” 1-3/4” 1.3 R2308 1.4 R10141-1/2” 1-15/16” 1.7 R2310 1.8 R1016

Black Galvanized

Size Part No. Part No.

1/8”* P5208 R01021/4”* R1420 R01043/8”* R1395 R01061/2” R1396 R01083/4” R1397 R0110

1” R1398 R01121-1/4” R1399 R0114

• Cap• Figure 1124• Malleable Iron Class 150*1/8”, 1/4”, 3/8” are Steel

Malleable Iron 90° Elbow Malleable Iron 45° Elbow

Malleable Iron Cap

Black Galvanized


1-1/2” R1400 R01162” R1401 R0118

2-1/2” R1402 R01203” R1404 R0122

3-1/2” - R01244” R1406 R0126

Malleable Iron 45° Street Elbow

Malleable Iron Straight Tee

Black Galvanized

NPS A Weight Part No. Weight Part No.

2” 2-1/4” 2.5 R2312 2.8 R10182-1/2” 2-11/16” 4.9 R2314 5.0 R1020

3” 3-1/16” 7.1 R2316 7.3 R10223-1/2” 3-7/16” 9.0 R2317 9.4 R1024

4” 3-13/16” 11 R2318 12 R10265” 4-1/2” 19 R2319 20 -6” 5-1/8” 26 - 30 -

��

www.bobdeansupply.comMalleableIron Fittings

• Reducing Elbow• Figure 1101R• Malleable Iron Class 150(Standard)

Black Galvanized

Size X Z Weight Part No. Weight Part No.

1/4” x 1/8” NPS 3/4” 3/4” 0.10 lbs - 0.10 lbs R06493/8” x 1/8” 13/16” 7/8” 0.12 - 0.13 -3/8” x 1/4” 7/8” 15/16” 0.14 - 0.15 R06501/2” x 1/4” 1” 1” 0.19 R1924 0.20 R06521/2” x 3/8” 1-1/6” 1-1/16” 0.21 R1932 0.22 R06543/4” x 1/4” 1-1/8” 1-1/8” 0.26 R1940 0.28 R06563/4” x 3/8” 1-1/8” 1-1/8” 0.29 - 0.30 R06583/4” x 1/2” 1-3/16” 1-1/4” 0.39 R1942 0.40 R0660

1” x 3/8” 1-3/16” 1-1/4” 0.41 - 0.42 R06621” x 1/2” 1-1/4” 1-3/8” 0.46 R1929 0.47 R06641” x 3/4” 1-3/8” 1-7/16” 0.55 R1928 0.58 R0666

1-1/4” x 1/2” 1-3/8” 1-9/16” 0.62 - 0.64 R06681-1/4” x 3/4” 1-7/16” 1-5/8” 0.71 R1931 0.73 R0670

1-1/4” x 1” 1-9/16” 1-11/16” 0.86 - 0.90 R06721-1/2” x 3/4” 1-1/2” 1-3/4” 0.83 - 0.85 R0680

1-1/2” x 1” 1-5/8” 1-13/16” 1.00 R1951 1.1 R06821-1/2” x 1-1/4” 1-13/16” 1-7/8” 1.2 R1926 1.2 R0684

2” x 3/4” 1-5/8” 2” 1.3 - 1.3 R06872” x 1” 1-3/4” 2” 1.4 R1925 1.5 R0688

2” x 1-1/4” 1-7/8” 2-1/8” 1.5 R1950 1.6 R06902” x 1-1/2” 2” 2-1/8” 1.8 R1952 1.8 R0692

2-1/2” x 1-1/2” 2-3/16” 2-1/2” 2.3 R1945 2.5 -2-1/2” x 2” 2-7/16” 2-5/8” 3.0 - 3.0 R0693

3” x 2” 2-9/16” 2-15/16” 3.8 - 3.9 R06943” x 2-1/2” 2-13/16” 3” 4.0 - 4.0 -

4” x 3” 3-5/16” 3-5/8” 7.9 R1930 8.0 -

• 90° Street Elbow• Figure 1103• Malleable Iron Class 150 (Standard)

Black Galvanized 316 S.S. Brass

NPS A J Part No. Part No. Part No. Part No.

1/8” 11/16” 1” R1998 R0702 - R31301/4” 13/16” 1-3/16” R2100 R0704 R2850 R31313/8” 15/16” 1-7/16” R1997 R0706 R2851 R31321/2” 1-1/8” 1-5/8” R2102 R0708 R2852 R31333/4” 1-5/16” 1-7/8” R2104 R0710 R2853 R3134

1” 1-1/2” 2-1/8” R2106 R0712 R2854 R31351-1/4” 1-3/4” 2-7/16” R2108 R0714 R2855 R31361-1/2” 1-15/16” 2-11/16” R2110 R0716 R2856 R3137

2” 2-1/4” 3-1/4” R2112 R0718 R2857 R31382-1/2” 2-11/16” 3-7/8” R2114 R0720 - -

3” 3-1/16” 4-1/2” R2116 R0722 SC648 -4” 3-13/16” 5-11/16” R2118 R0724 SC649 -

Pipe Size Length Width Threads Part No.

1/8” .625” 9/32” 271/4” .687” 3/8” 183/8” .812” 7/16” 181/2” .937” 9/16” 14

Malleable Iron Reducing ElbowMalleable Iron 90° Street Elbow

Merchant Steel Head Plugs

Black Galvanied

Size A Part No. Part No.

1/8” 11/16” - R04021/4” 13/16” R1690 R04043/8” 15/16” R1691 R04061/2” 1-1/8” R1692 R04083/4” 1-5/16” R0440 R0410

1” 1-1/2” P5209 R04121-1/4” 1-3/4” - R04141-1/2” 1-15/16” R1700 R0416

2” 2-1/4” R1703 R04182-1/2” 2-11/16” R1702 R0417

3” 3-1/16” - R04224” 3-13/16” - R0426

• Iron Cross• Malleable Iron Class 150

Malleable Iron Cross

Malleable Iron Floor Flange

• Floor Flange• Figure 1190• Malleable Iron Class 150 (*and cast iron)

Black Galvanized

Size Flange Dia. Bolt Circle Holes Hole Dia. Part No. Part No.

1/4”* 2-3/16” 1-7/8” 4 1/4” - R08003/8”* 3” 2” 4 1/4” - R07981/2” 3-1/2” 2-1/2” 4 1/4” R2420 R08023/4” 3-1/2” 2-1/2” 4 1/4” - R0804

1” 4” 3” 4 1/4” - R08061-1/4” 4” 3” 4 1/4” R2419 R08081-1/2” 4-1/2” 3-1/2” 4 5/16” - R0810

2” 5-1/2” 4-1/4” 4 5/16” - R0812*Cast Iron

1-800-282-8378

��


• Reducing Tee• Figure 1105R• Malleable Iron Class 150

Black Galvanized


3/8” x 1/4” x 1/4” - -3/8” x 1/4” x 3/8” - -3/8” x 1/4” x 1/2” - -3/8” x 3/8” x 1/4” R2322 R11053/8” x 3/8” x 1/2” - -1/2” x 1/4” x 1/2” - -1/2” x 3/8” x 3/8” - -1/2” x 1/2” x 1/4” R2334 R11101/2” x 1/2” x 3/8” - -1/2” x 1/2” x 3/4” - R1111

1/2” x 1/2” x 1” - -3/4” x 1/4” x 3/4” - -3/4” x 3/8” x 3/8” - -3/4” x 3/8” x 3/4” - -3/4” x 1/2” x 1/2” R2515 R11153/4” x 1/2” x 3/4” - R11313/4” x 3/4” x 1/4” - R11203/4” x 3/4” x 3/8” R2320 R11333/4” x 3/4” x 1/2” R2548 R1125

3/4” x 3/4” x 1” - R11303/4” x 3/4” x 1-1/4” - -

1” x 1/4” x 1” - -1” x 1/2” x 1/2” R2514 -1” x 1/2” x 3/4” - -

1” x 1/2” x 1” - R11361” x 3/4” x 1/2” - R11371” x 3/4” x 3/4” - R1139

1” x 3/4” x 1” - R11381” x 1” x 1/4” - -1” x 1” x 3/8” - -1” x 1” x 1/2” - R11351” x 1” x 3/4” R2513 R1140

1” x 1” x 1-1/4” - R11481” x 1” x 1-1/2” - -

1” x 1” x2” - -1-1/4” x 1/2” x 1” - -

1-1/4” x 1/2” x 1-1/4” - -1-1/4” x 3/4” x 3/4” - -

1-1/4” x 3/4” x 1” - -

Black Galvanized


1-1/4” x 3/4” x 1-1/4” - -1-1/4” x 1” x 1/2” - -1-1/4” x 1” x 3/4” R2511 -

1-1/4” x 1” x 1” - -1-1/4” x 1” x 1-1/4” - -

1-1/4” x 1-1/4” x 3/8” - -1-1/4” x 1-1/4” x 1/2” R2325 R11501-1/4” x 1-1/4” x 3/4” P6131 R1155

1-1/4” x 1-1/4” x 1” - R11601-1/4” x 1-1/4” x 1-1/2” - -

1-1/4” x 1-1/4” x 2” - -1=1/2” x 1/2” x 1-1/2” - -1-1/2” x 3/4” x 1-1/2” - -

1-1/2” x 3/4” x 3/4” - -1-1/2” x 1” x 1-1/2” - -1-1/2” x 1” x 1-1/4” R2332 -

1-1/2” x 1” x 1” R2512 -1-1/2” x 1-1/4” x 1/2” - -1-1/2” x 1-1/4” x 3/4” R2510 R1164

1-1/2” x 1-1/4” x1” - -1-1/2” x 1-1/4” x 1-1/4” R2521 -1-1/2” x 1-1/4” x 1-1/2” - -

1-1/2” x 1-1/2” x 1/2” R2330 R11651-1/2” x 1-1/2” x 3/4” - R1170

1-1/2” x 1-1/2” x 1” P6132 R11751-1/2” x 1-1/2” x 1-1/4” R2333 R1180

1-1/2” x 1-1/2” x 2” - -2” x 1/2” x 2” - -2” x 3/4” x 2” - -

2” x 1” x 2” - R11852” x 1-1/4” x 1-1/4” R2524 -2” x 1-1/4” x 1-1/2” - -

2” x 1-1/4” x 2” R2335 R11862” x 1-1/2” x 1” - -

2” x 1-1/2” x 1-1/4” - -2” x 1-1/2” x 1-1/2” R2336 -

2” x 1-1/2” x 2” - R11872” x 2” x 1/2” - R11902” x 2” x 3/4” - R1192

2” x 2” x 1” - R11942” x 2” x 1-1/4” R1933 R11962” x 2” x 1-1/2” - R11982” x 2” x 2-1/2” - -

Black Galvanized

Size W Part No. Part No.

1/8” 15/16” - -1/4” 1-1/16” - -3/8” 1-3/16” - -1/2” 1-5/16” - R15273/4” 1-1/2” R1529 R1528

1” 1-11/16” R1530 R02131-1/4” 1-15/16” R1531 R03761-1/2” 2-1/8” R1532 R1540

2” 2-1/2” R1533 -

• Coupling - Right Hand• Figure 1121• Malleable Iron Class 150

Malleable Iron Reducing Tee Malleable Iron Coupling

Black Galvanized

Size End to End Part No. Part No.

1/8” 1-5/16” - R12021/4”* 1-13/16” R2399 R12043/8”* 1-13/16” R2401 R12061/2”* 1-15/16” R2402 R12083/4”* 2-1/16” R2404 R1210

3/4” x 1/2”* 2-1/16” - -1”* 2-7/16” R2406 R1212

1-1/4”* 2-5/8” R2408 R12141-1/2”* 2-3/4” R2410 R1216

2”* 2-15/16” R2412 R12182-1/2” 3-5/8” R2414 R1220

3” 3-3/4” R2416 R1222

• Union• Figure 463• Malleable Iron Class 150• 150 lb. wsp• 300 lb. wog non-stock* denotes UL Listed

Malleable Iron Union

Nominal Pipe Size Length Width

1/4” x 1/8” .625” .625”3/8” x 1/8” .750” .687”3/8” x 1/4” .750” .687”1/2” x 1/8” .875” .875”1/2” x 1/4” .875” .875”1/2” x 3/8” .875” .875”3/4” x 1/8” 1.000” 1.062”3/4” x 1/4” 1.000” 1.062”3/4” x 3/8” 1.000” 1.062”3/4” x 1/2” 1.000” 1.062”

• All sizes taper tapped 3/4” per foot on diameter

Merch. Steel Hex Bushing

��

www.bobdeansupply.comMalleableIron Fittings

Black Galvanized

Size M Part No. Part No.

1/4” x 1/8” 1” R1569 R03023/8” x 1/8” 1-1/8” R1570 -3/8” x 1/4” 1-1/8” R1578 R03041/2” x 1/8” 1-1/4” - R03061/2” x 1/4” 1-1/4” R1580 R03081/2” x 3/8” 1-1/4” R1581 R03103/4” x 1/8” 1-7/16” R1579 -3/4” x 1/4” 1-7/16” R1582 R03123/4” x 3/8” 1-7/16” R1583 R03143/4” x 1/2” 1-7/16” R1584 R0316

1” x 1/4” 1-11/16” - R03181” x 3/8” 1-11/16” R1585 R03201” x 1/2” 1-11/16” R1586 R03221” x 3/4” 1-11/16” R1587 R0324

1-1/4” x 1/2” 2-1/16” R1589 R03261-1/4” x 3/4” 2-1/16” R1590 R0327

1-1/4” x 1” 2-1/16” R1591 R03281-1/2” x 1/2” 2-5/16” R1593 R03301-1/2” x 3/4” 2-5/16” R1594 R0332

1-1/2” x 1” 2-5/16” R1595 R03341-1/2” x 1-1/4” 2-5/16” R1596 R0336

2” x 1/2” 2-13/16” R1597 R03382” x 3/4” 2-13/16” R1598 R0340

2” x 1” 2-13/16” R1599 R03422” x 1-1/4” 2-13/16” R1600 R03442” x 1-1/2” 2-13/16” R1601 R03462-1/2” x 1” 3-1/4” R1602 R0350

2-1/2” x 1-1/4” 3-1/4” R1603 -2-1/2” x 1-1/2” 3-1/4” R1611 R0352

2-1/2” x 2” 3-1/4” R1614 R03513” x 1” 3-11/16” R1609 -

3” x 1-1/4” 3-11/16” - -3” x 1-1/2” 3-11/16” R1604 R0355

3” x 2” 3-11/16” R1615 R03563” x 2-1/2” 3-11/16” R1616 R03583-1/2” x 2” 4” - -

3-1/2” x 2-1/2” 4” - -3-1/2” x 3” 4” R1605 -4” x 1-1/2” 4-3/8” - -

4” x 2” 3-11/16” - R03664” x 2-1/2” 3-11/16” R1608 -

4” x 3” 3-11/16” R1606 R03704” x 3-1/2” 3-11/16” R1607 R0371

5” x 4” 4-9/16” - -6” x 4” 4-13/16” R1610 -

• Reducer• Figure 1125.• Malleable Iron Class 150

• 90° Elbow Straight• Figure 1161• Malleable Iron Class 300 (XS/XH)

Black Galvanized


1/4” NPS 15/16” - -3/8” 1-1/16” - -1/2” 1-1/4” R2583 -3/4” 1-7/16” R2574 -

1” 1-5/8” R2566 -1-1/4” 1-15/16” R2564 -1-1/2” 2-1/8” R2568 -

2” 2-1/2” R2107 -2-1/2” 2-15/16” - -

3” 3-3/8” R2577 -4” 4-1/2” - -

• 45° Elbow• Figure 1162• Malleable Iron Class 300 (XS/XH)

Black Galvanized

Size C Part No. Part No.

1/4” NPS 13/16” - -3/8” 7/8” - -1/2” 1” - -3/4” 1-1/8” R2585 -

1” 1-5/16” R2587 -1-1/4” 1-1/2” R2569 -1-1/2” 1-11/16” R2589 -

2” 2” - -2-1/2” 2-1/4” - -

3” 2-1/2” - -4” 2-13/16” - -

• Cross.• Figure 1165. • Malleable Iron Class 300 (XS/XH)

Black Galvanized


1/4” NPS 15/16” - -3/8” 1-1/16” - -3/4” 1-7/16” - -

1” 1-5/8” - -1-1/4” 1-15/16” - -1-1/2” 2-1/8” - -

2” 2-1/2” R0419 -

Black Galvanized

Size M Part No. Part No.

3/8” x 1/4” 1-7/16” R0381 -1/2” x 1/4” 1-11/16” R0382 -1/2” x 3/8” 1-11/16” R0383 -3/4” x 1/4” 1-3/4” - -3/4” x 3/8” 1-3/4” R0385 -3/4” x 1/2” 1-3/4” R0386 -

1” x 1/4” 2” - -1” x 3/8” 2” - -1” x 1/2” 2” R0387 -1” x 3/4” 2” R0388 -

1-1/4” x 1/2” 2-3/8” - -1-1/4” x 3/4” 2-3/8” R0389 -

1-1/4” x 1” 2-3/8” R0390 -1-1/2” x 1/2” 2-11/16” - -1-1/2” x 3/4” 2-11/16” R0394 -

1-1/2” x 1” 2-11/16” R0392 -1-1/2” x 1-1/4” 2-11/16” R0323 -

2” x 1/2” 3-3/16” - -2” x 3/4” 3-3/16” R0380 -

2” x 1” 3-3/16” R0397 -2” x 1-1/4” 3-3/16” R0396 -2” x 1-1/2” 3-3/16” R0395 -

• Reducer• Figure 1167• Malleable Iron Class 300 (XS/XH)

Malleable Iron Reducer

Cross - Extra Heavy

90° Elbow - Extra Heavy 45° Elbow - Extra Heavy

Reducer - Extra Heavy

Black Galvanized

Size End to End Part No. Part No.

1/8” 1-5/16” - -1/4” 1-13/16” - -3/8” 1-13/16” - -1/2” 2-1/16” R2586 -3/4” 2-1/4” R2588 -

1” 2-9/16” R2582 -1-1/4” 2-3/4” R2590 -1-1/2” 3” R2591 -

2” 3-3/8” R2579 -

• Union• F igure 459• Malleable Iron Class 300• 300 lb. wsp• 600 lb. wog non-stock

Union - Extra Heavy

1-800-282-8378

��


• Figure 387• 1/8”, 1/4” 3/8” are Steel

Black Galvanized

Size Hex Part No. Part No.

1/4” x 1/8” R1250 R00023/8” x 1/8” R1252 R00043/8” x 1/4” R1253 R00061/2” x 1/8” R1257 R00091/2” x 1/4” R1255 R00081/2” x 3/8” R1254 R00103/4” x 1/8” - R00113/4” x 1/4” R1256 R00123/4” x 3/8” R1258 R00143/4” x 1/2” R1260 R0016

1” x 1/8” ◊ - R00171” x 1/4” ◊ R1262 R00181” x 3/8” ◊ R1264 R00201” x 1/2” R1266 R00221” x 3/4” R1268 R0024

1-1/4” x 1/4” ◊ R1248 R00261-1/4” x 3/8” ◊ R1270 R00281-1/4” x 1/2” ◊ R1272 R00301-1/4” x 3/4” R1276 R0032

1-1/4” x 1” R1278 R00341-1/2” x 1/4” R1280 R00361-1/2” x 3/8” ◊ R1282 R00381-1/2” x 1/2” ◊ R1284 R00401-1/2” x 3/4” ◊ R1286 R0041

1-1/2” x 1” R1288 R00421-1/2” x 1-1/4” R1290 R0044

2” x 1/4” R1249 R00462” x 3/8” - R00482” x 1/2” ◊ R1292 R00502” x 3/4” ◊ R1294 R0051

2” x 1” ◊ R1296 R00522” x 1-1/4” ◊ R1298 R00542” x 1-1/2” ◊ R1299 R0056

2-1/2” x 1/2” ◊ - -2-1/2” x 3/4” ◊ R1302 R0060

2-1/2” x 1” ◊ R1304 R00622-1/2” x 1-1/4” ◊ R1306 R0064

• Hex Bushing• Figure 383◊ Denotes Inside Hex

Black Galvanized

Size Hex Part No. Part No.

2-1/2” x 1-1/2” ◊ R1308 R00662-1/2” x 2” R1310 R0068

3” x 1/2” ◊ R2532 -3” x 3/4” ◊ R1311 -

3” x 1” ◊ R1312 R00703” x 1-1/4” ◊ R1314 R00723” x 1-1/2” ◊ R1316 R0074

3” x 2” R1318 R00763” x 2-1/2” R1320 R00783-1/2” x 1” ◊ - -

3-1/2” x 1-1/4” ◊ R1322 -3-1/2” x 1-1/2” ◊ R1324 R0080

3-1/2” x 2” ◊ R1326 R00813-1/2” x 2-1/2” - R0079

3-1/2” x 3” R1328 -4” x 1” ◊ R1330 R0082

4” x 1-1/4” ◊ R1332 R00834” x 1-1/2” ◊ R1334 R0084

4” x 2” ◊ R1336 R00854” x 2-1/2” ◊ R1338 R0086

4” x 3” R1340 R00874” x 3-1/2” R1342 -

5” x 2” ◊ - -5” x 2-1/2” ◊ R1341 -

5” x 3” ◊ R1343 R00925” x 3-1/2” - -

5” x 4” R1344 R00886” x 2” ◊ - -

6” x 2-1/2” ◊ - -6” x 3” ◊ R1346 R0089

6” x 3-1/2” ◊ - -6” x 4” ◊ R1345 R00906” x 5” R1347 -8” x 3” ◊ - -8” x 4” ◊ R1348 -8” x 5” ◊ R1349 -8” x 6” R1350 -

Size Black & Galvanized

3/4” -1” -

1-1/4” -1-1/2” -

2” -

• Figure 381


2-1/2” -3” -4” -5” -6” -

• Straight Tee• Figure 1164• Malleable Iron Class 300 (XS/XH)

Black Galvanized


1/4” NPS 1-5/16” - -3/8” 1-1/16” - -1/2” 1-1/4” R2593 -3/4” 1-7/16” R2595 -

1” 1-5/8” R2565 -1-1/4” 1-15/16” R2555 -1-1/2” 2-1/8” R2517 -

2” 2-1/2” R2596 -2-1/2” 2-15/16” R2526 -

3” 3-3/8” - -4” 4-1/2” - -

Straight Tee - Extra Heavy Cast Iron Square Head Plugs

Cast Iron Cap

Cast Iron Hex Bushings


2-1/2” -3” -

3-1/2” -4” -

��0

www.bobdeansupply.comSteelFittings

• Manufactured in accordance with ASTM specification A865• Merchant couplings in sizes 1/8” NPS through 2” NPS are normally supplied straight tapped• Sizes 2-1/2” NPS and larger are taper tapped•API line pipe couplings are used in all sizes over 6” NPS•Couplings from 1/8” NPS through 2” NPS are dipped in rust preventative•Couplings 2-1/2” and larger are phosphated

Black Galvanized

Size (NPS) Outside Dia. Length (Full) Threads Part No. Part No.

1/8” .563” 13/16” 27 R1499 R02021/4” .719” 1-3/16” 18 R1500 R02043/8” .875” 1-3/16” 18 R1501 R02061/2” 1.063” 1-9/16” 14 R1502 R02083/4” 1.313” 1-5/8” 14 R1504 R0210

1” 1.576” 2” 11-1/2 R1506 R02121-1/4” 1.900” 2-1/16” 11-1/2 R1508 R02141-1/2” 2.200” 2-1/16” 11-1/2 R1510 R0216

2” 2.750” 2-1/8” 11-1/2 R1512 R02182-1/2” 3.250” 3-1/8” 8 R1513 R0220

3” 4.000” 3-1/4” 8 R1514 R02223-1/2” 4.625” 3-3/8” 8 R1515 R0223

4” 5.000” 3-1/2” 8 R1516 R02245” 6.296” 3-3/4” 8 R1518 R02256” 7.390” 4” 8 R1520 R02268” - - - R1522 -

12” - - - R1524 -

• Manufactured in accordance with ASTM specification A865• All sizes are taper tapped•Recessed couplings•Couplings 1/8” - 1-1/2” NPS are dipped in rust preventative•Couplings 2” NPS and larger are phosphated

Black Galvanized

Size (NPS) Outside Dia. Length (Full) Part No. Part No.

1/8” .563” 1-1/16” - -1/4” .719” 1-5/8” R2525 -3/8” .875” 1-5/8” R2544 -1/2” 1.063” 2-1/8” R2558 -3/4” 1.313” 2-1/8” P6056 -

1” 1.576” 2-5/8” R2559 -1-1/4” 2.054” 2-3/4” R2572 -1-1/2” 2.200” 2-3/4” R2581 -

2” 2.875” 2-7/8” R2571 -2-1/2” 3.375” 4-1/8” - R0242

3” 4.000” 4-1/4” - -3-1/2” 4.625” 4-3/8” - -

4” 5.200” 4-1/2” - -5” 6.296” 4-5/8” - -6” 7.390” 4-7/8” - -8” 9.625” 5-1/4” - -

10” 11.750” 5-3/4” - -12” 14.000” 6-1/8” - -

Standard Steel Merchant Couplings

Extra Heavy Steel Merchant Couplings

1-800-282-8378

��

Butt WeldFittings

NominalPipe Size Schedule O.D. I.D. Wall Center to End Part No.

1/2” 40 .840” .622” .109 1-1/2” SC3013/4” 40 1.050 .824 .113 1-1/8 SC302

1” 40 1.315 1.049 .133 1-1/2 SC3031-1/4” 40 1.660 1.380 .140 1-7/8 SC3041-1/2” 40 1.900 1.610 .145 2-1/4 SC305

2” 40 2.375 2.067 .154 3 SC3062-1/2” 40 2.875 2.469 .203 3-3/4 -

3” 40 3.500 3.068 .216 4-1/2 SC3073-1/2” 40 4.000 3.548 .226 5-1/4 -

4” 40 4.500 4.026 .237 6 SC3085” 40 5.563 5.047 .258 7-1/2 -6” 40 6.625 6.065 .280 9 -8” 40 8.625 7.981 .322 12 -

10” 40 10.750 10.020 .365 15 -12” * 12.750 12.000 .375 18 -14” 30 14.000 13.250 .375 21 -16” 30 16.000 15.250 .375 24 -18” * 18.000 17.250 .375 27 -20” 20 20.000 19.250 .375 30 -24” 20 24.000 23.250 .375 36 -

• Standard Weight* This size does not correspond to any pipe schedule number


1” 40 1.315” 1.049” .133 1” -1-1/4” 40 1.660 1.380 .140 1-1/4 -1-1/2” 40 1.900 1.610 .145 1-1/2 -

2” 40 2.375 2.067 .154 2 S31402-1/2” 40 2.875 2.469 .203 2-1/2 S3141

3” 40 3.500 3.068 .216 3 S31423-1/2” 40 4.000 3.548 .226 3-1/2 S3143

4” 40 4.500 4.026 .237 4 S31445” 40 5.563 5.047 .258 5 S31466” 40 6.625 6.065 .280 6 S31488” 40 8.625 7.981 .322 8 S3150

10” 40 10.750 10.020 .365 10 S316012” * 12.750 12.000 .375 12 S316214” 30 14.000 13.250 .375 14 -16” 30 16.000 15.250 .375 16 -18” * 18.000 17.250 .375 18 -20” 20 20.000 19.250 .375 20 -24” 20 24.000 23.250 .375 24 -



1/2” 40 .840” .622” .109 5/8” S24603/4” 40 1.050 .824 .113 7/16 S2461

1” 40 1.315 1.049 .133 7/8 S30021-1/4” 40 1.660 1.380 .140 1 S30041-1/2” 40 1.900 1.610 .145 1-1/8 S3006

2” 40 2.375 2.067 .154 1-3/8 S30082-1/2” 40 2.875 2.469 .203 1-3/4 S3010

3” 40 3.500 3.068 .216 2 S30123-1/2” 40 4.000 3.548 .226 2-1/4 -

4” 40 4.500 4.026 .237 2-1/2 S30165” 40 5.563 5.047 .258 3-1/8 S30186” 40 6.625 6.065 .280 3-3/4 S30208” 40 8.625 7.981 .322 5 S3022

10” 40 10.750 10.020 .365 6-1/4 S302412” * 12.750 12.000 .375 7-1/2 S302614” 30 14.000 13.250 .375 8-3/4 -16” 30 16.000 15.250 .375 10 S303018” * 18.000 17.250 .375 11-1/4 -20” 20 20.000 19.250 .375 12-1/2 -24” 20 24.000 23.250 .375 15 -


• Standard Weight Nominal Pipe Size Length (E) Part No.

1/2” 1” -3/4” 1 -

1” 1-1/2 -1-1/4” 1-1/2 S33351-1/2” 1-1/2 S3336

2” 1-1/2 S33372-1/2” 1-1/2 S3338

3” 2 S33393-1/2” 2-1/2 S3334

4” 2-1/2 S33405” 3 S33416” 3-1/2 S33428” 4 S3349

10” 5 S335112” 6 S335414” 6-1/2 -16” 7 -18” 8 -20” 9 -24” 10-1/2 -

90° Elbow - Long Radius 45° Elbow - Long Radius

90° Elbow - Short Radius Weld Caps

��

www.bobdeansupply.comButt WeldFittings

NominalPipe Size Outside Diameter Thickness Weld Neck Bore Slip-On Bore Weld Neck Hub Slip-On Hub Weld Neck

Part No.Slip-On Part No.

Blind Part No.

1/2” 3-1/2” 7/16” .62” .88” 1-7/8” 5/8” - S3300 -3/4” 3-7/8 1/2 .82 1.09 2-1/16 5/8 - S3442 -

1” 4-1/4 9/16 1.05 1.36 2-3/16 11/16 - S3302 -1-1/4” 4-5/8 5/8 1.38 1.70 2-1/4 13/16 - S3304 -1-1/2” 5 11/16 1.61 1.95 2-7/16 7/8 S3348 S3306 -

2” 6 3/4 2.07 2.44 2-1/2 1 S3350 S3308 -2-1/2” 7 7/8 2.47 2.94 2-3/4 1-1/8 S3356 S3310 -

3” 7-1/2 15/16 3.07 3.57 2-3/4 1-3/16 S3352 S3312 -3-1/2” 8-1/2 15/16 3.55 4.07 2-13/16 1-1/4 - S3314 -

4” 9 15/16 4.03 4.57 3 1-5/16 S3353 S3316 -5” 10 15/16 5.05 5.66 3-1/2 1-7/16 - S3318 S32946” 11 1 6.07 6.72 3-1/2 1-9/16 S3357 S3320 -8” 13-1/2 1-1/8 7.98 8.72 4 1-3/4 - S3322 S3296

10” 16 1-3/16 10.02 10.88 4 1-15/16 - S3324 -12” 19 1-1/4 12.00 12.88 4-1/2 2-3/16 - S3326 -14” 21 1-3/8 13.25 14.14 5 2-1/4 - S3327 -16” 23-1/2 1-7/16 15.25 16.16 5 2-1/2 - S3328 -18” 25 1-9/16 17.25 18.18 5-1/2 2-11/16 - - -20” 27-1/2 1-11/16 19.25 20.20 5-11/16 2-7/8 - - -24” 32 1-7/8 23.25 24.25 6 3-1/4 S3330

Welding Neck Slip-On Blind

Welding Neck, Slip-On & Blind Flanges - 150 Lb.

Socket Weld Anvilets - Full and Reducing Sizes (Weld-O-Let

Outlet Size-NPS Nominal Run Pipe Part No.

1/2” 1/2” -1/2” 3/4-36 -3/4” 3/4 S21013/4” 1 - 36 -

1” 1 -1” 1-1/4 - 36 -1” 3 - 3-1/2 S21031” 4” S2104

1-1/4” 1-1/4 -1-1/4” 1-1/2 - 36 -1-1/2” 1-1/2 -1-1/2” 2 - 36 -1-1/2” 3 S21021-1/2” 5 - 6 S2106

2” 2 S24002” 2-1/2 - 36 S2110

2-1/2” 2-1/2 -2-1/2” 3 - 36 S21182-1/2” 4 S2120

• Class 3000 Seamless Steel•May be used with Std. and XS pipe•Seamless Steel


2-1/2” 5 S21212-1/2” 6 S21222-1/2” 8 S2123

3” 3 -3” 3-1/2 - 36 -3” 4 S21263” 5 S21273” 6 S21283” 8 S2129

3-1/2” 3-1/2 -3-1/2” 4 - 36 -

4” 4 -4” 5 - 36 -4” 5 S21334” 6 S21344” 8 S21356” 8 S21408” 10 S2200

*Tolerance on sizes 2-1/2 NPS and larger is +/-.06”

1-800-282-8378

��

Butt WeldFittings


1/2” 1/2” -1/2” 3/4-36 -1/2” 1-1/4 - 1-1/2 S20011/2” 2 - 2-1/2 S20031/2” 2-1/2 - 8 S20043/4” 3/4 -3/4” 1 - 36 -3/4” 1-1/4 - 1-1/2 S20063/4” 2 - 2-1/2 S20083/4” 2-1/2 - 8 S2009

1” 1 -1” 1-1/4 - 36 S20101” 2 - 2-1/2 S20121” 3 - 4 S20141” 5 - 8 S2015

1-1/4” 1-1/4 S24011-1/4” 1-1/2 - 2 S20171-1/4” 2 - 2-1/2 S20181-1/4” 3 - 4 S20201-1/4” 5 - 8 S20211-1/2” 1-1/2 -1-1/2” 2 S20231-1/2” 2-1/2 S20241-1/2” 3 - 4 S2025

• Class 3000 Seamless Steel•May be used with Std. and XS pipe•Female Threaded


1-1/2” 5 - 8 S20272” 2 -2” 2-1/2 S20292” 3 S20302” 4 S20312” 6 S20332” 8 S20342” 12 S2035

2-1/2” 2-1/2 -2-1/2” 3 S20362-1/2” 4 S20372-1/2” 6 S20392-1/2” 8 S2040

3” 3 -3” 3-1/2 - 36 -3” 4 S20453” 6 S20443” 8 S2042

3-1/2” 3-1/2 -3-1/2” 4 - 36 -

4” 4 -4” 5 -4” 6 S20484” 8 S2049

Nom. Pipe Size Length (H) Part No.

3/4” x 1/2” 1-1/2” S34351” x 1/2” 2 S34321” x 3/4” 2 S3433

1-1/4” x 1/2” 2 -1-1/4” x 3/4” 2 -

1-1/4” x 1” 2 S34311-1/2” x 1/2” 2-1/2 S34381-1/2” x 3/4” 2-1/2 -

1-1/2” x 1” 2-1/2 S34271-1/2” x 1-1/4” 2-1/2 S3428

• Standard Weight• Available to 42” x 36”

Threaded Anvilets - Full and Reducing Sizes (Thread-O-Let)

Concentric Reducers


2” x 3/4” 3 S34262” x 1” 3 S3436

2” x 1-1/4” 3 S34372” x 1-1/2” 3 S34252-1/2” x 1” 3-1/2 S3462

2-1/2” x 1-1/4” 3-1/2 S34612-1/2” x 1-1/2” 3-1/2 S3440

2-1/2” x 2” 3-1/2 S34223” X 3/4” 3-1/2 S3439

3” x 1” 3-1/2 S34183” x 1-1/4” 3-1/2 S34213” x 1-1/2” 3-1/2 S3441

3” x 2” 3-1/2 S34203” x 2-1/2” 3-1/2 S3419

3-1/2” x 1-1/4” 4 -3-1/2” x 1-1/2” 4 -

3-1/2” x 2” 4 -3-1/2” x 2-1/2” 4 -

3-1/2” x 3” 4 -4” x 1” 4 S3429

4” x 1-1/4” 4 -4” x 1-1/2” 4 S3430

4” x 2” 4 S34144” x 2-1/2” 4 S3417


4” x 3” 4 S34164” x 3-1/2” 4 -

5” x 2” 5 S34155” x 2-1/2” 5 S3434

5” x 3” 5 S34125” x 3-1/2” 5 -

5” x 4” 5 S34136” x 2” 5-1/2 S3423

6” x 2-1/2” 5-1/2 S34086” x 3” 5-1/2 S3411

6” x 3-1/2” 5-1/2 -6” x 4” 5-1/2 S34106” x 5” 5-1/2 S34098” x 3” 6 -

8” x 3-1/2” 6 -8” x 4” 6 S34048” x 5” 6 S34058” x 6” 6 -

10” x 4” 7 -10” x 5” 7 -10” x 6” 7 -10” x 8” 7 S340312” x 4” 8 -12” x 5” 8 -


12” x 6” 8 -12” x 8” 8 S3498

12” x 10” 8 S340014” x 6” 13 -14” x 8” 13 -

14” x 10” 13 -14” x 12” 13 S340116” x 6” 14 -16” x 8” 14 -

16” x 10” 14 -16” x 12” 14 -16” x 14” 14 -18” x 10” 15 -18” x 12” 15 -18” x 14” 15 -18” x 16” 15 -20” x 10” 20 -20” x 12” 20 -20” x 14” 20 -20” x 16” 20 -20” x 18” 20 -24” x 16” 20 -24” x 18” 20 -24” x 20” 20 -

��

www.bobdeansupply.comButt WeldFittings

Butt Weld Fittings are also available in 304 and 316 Stainless Steel. Some sizes of Slip-On Welding Neck Flanges, 90 Degree Elbows and 45 Degree Elbows may be in stock. Please check with your Sales Associate for availability.

Stainless Steel Butt Weld Fittings

• Standard Weight Seamless Steel

Nominal Pipe Size

Run

Nominal Pipe Size

Branch

Center to End of Run C

Center to End of

Branch MPart No.

1/2” 1/2” 1” 1” S35001/2” 3/8 1 1 -1/2” 1/4 1 1 -3/4” 3/4 1-1/8 1-1/8 S35013/4” 1/2 1-1/8 1-1/8 -3/4” 3/8 1-1/8 1-1/8 -

1” 1 1-1/2 1-1/2 S35021” 3/4 1-1/2 1-1/2 -1” 1/2 1-1/2 1-1/2 -1” 3/8 1-1/2 1-1/2 -

1=1/4” 1-1/4 1-7/8 1-7/8 S35041-1/4” 1 1-7/8 1-7/8 S35251-1/4” 3/4 1-7/8 1-7/8 -1-1/4” 1/2 1-7/8 1-7/8 -1-1/2” 1-1/2 2-1/4 2-1/4 S35061-1/2” 1-1/4 2-1/4 2-1/4 -1-1/2” 1 2-1/4 2-1/4 -1-1/2” 3/4 2-1/4 2-1/4 -1-1/2” 1/2 2-1/4 2-1/4 -

2” 2 2-1/2 2-1/2 S35082” 1-1/2 2-1/2 2-3/8 S35362” 1-1/4 2-1/2 2-1/4 S35292” 1 2-1/2 2 -2” 3/4 2-1/2 1-3/4 -

2-1/2” 2-1/2 3 3 S35102-1/2” 2 3 2-3/4 S35332-1/2” 1-1/2 3 2-5/8 S35342-1/2” 1-1/4 3 2-1/2 S35352-1/2” 1 3 2-1/4 S3526

3” 3 3-3/8 3-3/8 S3512

Straight & Reducing Tees

Nominal Pipe Size

Run

Nominal Pipe Size

Branch


Center to End of

Branch MPart No.

3” 2-1/2 3-3/8 3-1/4 S35633” 2 3-3/8 3 S35303” 1-1/2 3-3/8 2-7/8 S35283” 1-1/4 3-3/8 2-3/4 -3” 1 3-3/8 2-5/8 -

3-1/2” 3-1/2 3-3/4 3-3/4 -3-1/2” 3 3-3/4 3-5/8 -3-1/2” 2-1/2 3-3/4 3-1/2 -3-1/2” 2 3-3/4 3-1/4 -3-1/2” 1-1/2 3-3/4 3-1/8 -

4” 4 4-1/8 4-1/8 S35164” 3-1/2 4-1/8 4 -4” 3 4-1/8 3-7/8 S35604” 2-1/2 4-1/8 3-3/4 -4” 2 4-1/8 3-1/2 -4” 1-1/2 4-1/8 3-3/8 -5” 5 4-7/8 4-7/8 S35185” 4 4-7/8 4-5/8 S35385” 3-1/2 4-7/8 4-1/2 -5” 3 4-7/8 4-3/8 S35325” 2-1/2 4-7/8 4-1/4 -5” 2 4-7/8 4-1/8 -6” 6 5-5/8 5-5/8 S35206” 5 5-5/8 5-3/8 -6” 4 5-5/8 5-1/8 S35546” 3-1/2 5-5/8 5 -6” 3 5-5/8 4-7/8 -6” 2-1/2 5-5/8 4-3/4 -6” 2 5-5/8 4-5/8 -8” 8 7 7 S35228” 6 7 6-5/8 S35508” 5 7 6-3/8 -8” 4 7 6-1/8 S35528” 3-1/2 7 6 -8” 3 7 6 -

10” 10 8-1/2 8-1/2 S352310” 8 8-1/2 8 -10” 6 8-1/2 7-5/8 S357510” 5 8-1/2 7-1/2 -10” 4 8-1/2 7-1/4 -

Nominal Pipe Size

Run

Nominal Pipe Size

Branch


Center to End of

Branch MPart No.

10” 3 8-1/2 7 -12” 12 10 10 S352412” 10 10 9-1/2 -12” 8 10 9 -12” 6 10 8-5/8 -12” 5 10 8-1/2 -12” 4 10 8-1/4 -14” 14 11 11 -14” 12 11 10-5/8 -14” 10 11 10-1/8 -14” 8 11 9-3/4 -14” 6 11 9-3/8 -16” 16 12 12 -16” 14 12 12 -16” 12 12 11-5/8 -16” 10 12 11-1/8 -16” 8 12 10-3/4 -16” 6 12 10-3/8 -18” 18 13-1/2 13-1/2 -18” 16 13-1/2 13 -18” 14 13-1/2 13 -18” 12 13-1/2 12-5/8 -18” 10 13-1/2 12-1/8 -18” 8 13-1/2 11-3/4 -20” 20 15 15 -20” 18 15 14-1/2 -20” 16 15 14 -20” 14 15 14 -20” 12 15 13-5/8 -20” 10 15 13-1/8 -20” 8 15 12-3/4 -24” 24 17 17 -24” 20 17 17 -24” 18 17 16-1/2 -24” 16 17 16 -24” 14 17 16 -24” 12 17 15-5/8 -24” 10 17 15-1/8 -

1-800-282-8378

��


3/4” x 1/2” 1-1/2” -1” x 1/2” 2 -1” x 3/4” 2 -

1-1/4” x 1/2” 2 -1-1/4” x 3/4” 2 -

1-1/4” x 1” 2 -1-1/2” x 1/2” 2-1/2 -1-1/2” x 3/4” 2-1/2 -

1-1/2” x 1” 2-1/2 -1-1/2” x 1-1/4” 2-1/2 -

2” x 3/4” 3 -2” x 1” 3 -

2” x 1-1/4” 3 -


2” x 1-1/2” 3 -2-1/2” x 1” 3-1/2 -

2-1/2” x 1-1/4” 3-1/2 -2-1/2” x 1-1/2” 3-1/2 -

2-1/2” x 2” 3-1/2 S34633” X 3/4” 3-1/2 -

3” x 1” 3-1/2 -3” x 1-1/4” 3-1/2 -3” x 1-1/2” 3-1/2 -

3” x 2” 3-1/2 -3” x 2-1/2” 3-1/2 S3460

3-1/2” x 1-1/4” 4 -3-1/2” x 1-1/2” 4 -

3-1/2” x 2” 4 -3-1/2” x 2-1/2” 4 -

3-1/2” x 3” 4 -4” x 1” 4 -

4” x 1-1/4” 4 -4” x 1-1/2” 4 -

4” x 2” 4 S34594” x 2-1/2” 4 S3458

4” x 3” 4 S34574” x 3-1/2” 4 -


5” x 2” 5 -5” x 2-1/2” 5 -

5” x 3” 5 -5” x 3-1/2” 5 -

5” x 4” 5 S34546” x 2” 5-1/2 -

6” x 2-1/2” 5-1/2 -6” x 3” 5-1/2 S3451

6” x 3-1/2” 5-1/2 -6” x 4” 5-1/2 S34506” x 5” 5-1/2 S34498” x 3” 6 -

8” x 3-1/2” 6 -8” x 4” 6 -8” x 5” 6 S34488” x 6” 6 -

10” x 4” 7 -10” x 5” 7 -10” x 6” 7 -10” x 8” 7 -12” x 4” 8 -12” x 5” 8 -12” x 6” 8 -


12” x 8” 8 -12” x 10” 8 -14” x 6” 13 -14” x 8” 13 -

14” x 10” 13 -14” x 12” 13 -16” x 6” 14 -16” x 8” 14 -

16” x 10” 14 -16” x 12” 14 -16” x 14” 14 -18” x 10” 15 -18” x 12” 15 -18” x 14” 15 -18” x 16” 15 -20” x 10” 20 -20” x 12” 20 -20” x 14” 20 -20” x 16” 20 -20” x 18” 20 -24” x 16” 20 -24” x 18” 20 -24” x 20” 20 -

• Standard Weight• Available to 42” x 36”

Eccentric Reducers

Butt WeldFittings

BallValves

BA200 - Milwaukee BA100 - Milwaukee BA200S - Milwaukee

Bronze Ball Valve with Stainless Steel Ball. Two piece, standard port. 600 PSIG WOG / 150 PSIG SWP. Threaded ends. 1/4” to 3”.

Size B C E Part No.

1/4” 1.65 0.83 3.31 P00213/8” 1.65 0.83 3.31 P00221/2” 2.30 1.15 3.31 P00233/4” 2.55 1.28 3.31 P0024

1” 3.05 1.53 4.65 P00251-1/4” 3.43 1.72 4.65 P00261-1/2” 3.76 1.88 5.28 P0027

2” 4.21 2.11 5.28 P0028

Size A D E Part No.

1/4” 0.38 1.78 3.81 P00003/8” 0.38 1.81 3.81 P00011/2” 0.50 1.91 3.81 P00023/4” 0.76 2.08 4.56 P0003

1” 0.88 2.25 4.56 P00041-1/4” 1.06 2.66 6.31 P00051-1/2” 1.31 2.84 6.31 P0006

2” 1.56 3.00 7.19 P00072-1/2” 2.00 3.47 7.19 P0008

3” 2.31 3.90 7.19 P0009

Bronze Ball Valve. Two piece, standard port. 600 PSIG WOG / 150 PSIG SWP. Threaded ends.Available 1/4” to 3”.

Size A D E Part No.

1/4” 0.38 1.78 3.81 P00123/8” 0.38 1.78 3.81 P00131/2” 0.50 1.81 3.81 P00143/4” 0.76 2.08 4.56 P0015

1” 0.88 2.25 4.56 P00161-1/4” 1.06 2.66 6.31 P00171-1/2” 1.31 2.84 6.31 P0018

2” 1.56 3.00 7.19 P0019

Forged Brass Ball Valve. Two piece, standard port. 400 PSIG WOG / 150 PSIG SWP. Threaded ends. 1/4” to 4”.

��

www.bobdeansupply.comBallValves

3 Piece Stainless - Sharpe 2 Piece Stainless - Sharpe 3” & 4” Full Port - Jomar

3-Piece Full Port Ball Valve. Stainless Steel. 1000 WOG. Blowout proof stem. Actuator mounting pad. Locking device. Threaded, socket weld & butt weld ends. No. 53036. Sharpe Valves.

Size A D C Part No.

1/4” 0.83 4.05 1.83 -3/8” 0.83 4.05 1.83 -1/2” 0.92 4.05 1.95 P19423/4” 1.30 4.92 2.13 -

1” 1.48 6.50 2.50 -1-1/4” 1.84 6.50 2.76 -1-1/2” 2.27 7.50 3.09 P1985

2” 2.73 7.50 3.25 P19862-1/2” 3.39 9.85 5.35 -

3” 4.02 9.85 5.90 -4” 5.01 11.33 6.77 -

Threaded Full Port Ball Valve. Two piece. Class 1000 WOG. ASTMA-351. Blowout proof stem. Locking device and oval handle optional. No. 50M76. Sharpe Valves.

Size A B D Part No.

1/4” 2.00 0.43 4.00 -3/8” 2.00 0.43 4.00 -1/2” 2.36 0.50 4.00 P19493/4” 2.75 0.80 5.00 P1950

1” 3.25 1.00 5.75 P19511-1/4” 3.80 1.25 5.75 P19521-1/2” 4.33 1.50 7.50 P1953

2” 5.27 2.00 7.50 P19542-1/2” 6.58 2.50 9.73 P1955

3” 7.55 3.00 9.73 P1956

J-Flo by Jomar. 1/4 turn lever handle operated, hot forged brass, economical ball valve. 100% full port. Blowout proof stem and 2-piece body design. 600 WOG / 150 WSP. Gland follower and single O-ring stem design. Teflon seats and stem packing. Tested to military standard 105E in the USA. No. JF-100T.

Size A B C Part No.

1/4” 1.73 1.67 3.35 -3/8” 1.75 1.67 3.35 -1/2” 2.28 1.81 3.35 -3/4” 2.51 2.36 4.29 -

1” 2.97 2.52 4.29 -1-1/4” 3.43 2.52 5.63 -1-1/2” 3.86 2.80 5.63 -

2” 4.29 3.11 5.63 -2-1/2” 5.59 4.29 7.76 -

3” 6.42 4.85 8.35 P20684” 7.68 5.71 9.26 P2069

Bolted Polypropylene Ball Valves -Full and Standard - Dixon

1/2” to 3” is rated to 125 PSI at 70°F. 4” is rated to 90 PSI. Chemically-resistant, reinforced polypropylene. FDA approved material. Teflon ball seats. EPDM O-ring body seats, Viton O-ring stem seals. 304 stainless steel nuts and bolts. 4-bolt and 6-bolt valve designs. Female NPT X Female NPT. Dixon Valve & Coupling Co.

Size Port Model Bolts Part No.

1/2” Full PVFP50 4 -3/4” Full PVFP75 4 P2850

1” Full PVFP100 4 -1-1/2” Full PVFP150 4 P2864

1” Standard PV100 4 P28512” Standard PV200 4 P28542” Full PVFP200 6 P28653” Full PVFP300 6 P28674” Full PVFP400 6 -

4-Bolt Valve DesignFemale NPT

XFemale NPT

6-Bolt Valve DesignFemale NPT

XFemale NPT




1-800-282-8378

��

105 Bronze - Milwaukee

GateValves

1150 Bronze - Milwaukee 1153 Bronze - Milwaukee

105 Bronze Gate Valve. 125 lb. SWP - 200 lb. WOG. General service. Solid wedge disc. Non-rising stem. Threaded bonnet. Gland packed. Threaded ends. 4” size has split wedge and bolted bonnet. Milwaukee Valve.

Size A B C Part No.

1/4” 1.75 3.63 2.00 -3/8” 1.81 3.63 2.00 P00301/2” 2.00 3.63 2.00 P00313/4” 2.13 4.38 2.50 P0032

1” 2.56 5.00 2.75 P00331-1/4” 2.78 5.31 3.13 P00341-1/2” 2.81 6.34 3.50 P0035

2” 3.31 7.44 3.75 P00362-1/2” 4.19 9.13 4.75 P0037

3” 4.63 10.47 5.25 P00384” 5.50 15.50 5.25 -

Size A B C Part No.

1/4” 1.75 4.38 2.00 P09203/8” 1.81 4.38 2.00 P09221/2” 2.00 4.38 2.00 P09243/4” 2.13 5.84 2.50 P0926

1” 2.56 7.06 2.75 P09281-1/4” 2.78 8.78 3.13 P00401-1/2” 2.81 9.50 3.50 P0930

2” 3.31 11.50 3.75 P00392-1/2” 4.19 14.31 4.75 -

3” 4.63 16.63 5.25 -4” 5.50 15.50 5.25 -

1150 Bronze Gate Valve. 150 lb. SWP - 300 lb. WOG. General service. Solid wedge disc. Rising stem. Threaded bonnet. Gland packed. Threaded ends. 4” size has split wedge and bolted bonnet. Milwaukee Valve.

1153 Bronze Gate Valve. 200 lb. SWP - 400 lb. WOG. Industrial service. Solid wedge disc. Rising stem. Union bonnet. Gland packed. Threaded ends. Milwaukee Valve.

Size A B C Part No.

1/4” 1.75 5.13 2.25 -3/8” 1.88 5.13 2.25 -1/2” 2.25 5.50 2.50 P00413/4” 2.50 6.25 2.75 P0042

1” 2.88 7.19 2.75 P00431-1/4” 3.25 8.56 3.25 P00441-1/2” 3.50 9.56 3.75 P0045

2” 3.75 11.75 4.25 P00462-1/2” 4.63 14.50 4.75 -

3” 5.00 16.75 5.50 -

1184 Bronze - Milwaukee

1184 Bronze Gate Valve. 300 lb. SWP - 1000 lb. WOG. Heavy duty service. Solid wedge disc. Rising stem. Stainless seat. Gland packed. Union bonnet. Threaded ends. Wear-resistant stainless seat rings are securely expanded into the body to assure trouble-free service. Milwaukee Valve.

Size A B C Part No.

1/4” 1.81 5.13 2.25 -3/8” 1.88 5.13 2.25 -1/2” 2.25 5.50 2.50 P20233/4” 2.50 6.25 2.75 P2024

1” 3.00 7.19 2.75 P20251-1/4” 3.38 8.56 3.25 -1-1/2” 3.50 9.63 3.75 P2027

2” 3.75 11.75 4.25 -2-1/2” 4.63 14.50 4.75 -

3” 5.00 16.75 5.50 -

Threaded Gate - Webstone Quick Opening - Webstone

Gate Valve. IPS. 150 WSP / 300 WOG. Heavy Pattern Brass. Full flow, non-rising stem. Heavy duty cast iron handle. Spare parts available. Webstone.

Quick Opening Gate Valves. 150 WSP / 300 WOG. Heavy Pattern Bronze. Webstone.

Size Model Part No.

1/4” 10150 P26203/8” 10151 P26211/2” 10152 P26223/4” 10153 P2623

1” 10154 P26241-1/4” 10155 P26251-1/2” 10156 P2626

2” 10157 P26272-1/2” 10158 P2628

3” 10159 P26294” 10160 P2630

Size Model Part No.

3/8” 10301 P26311/2” 10302 P26323/4” 10303 P2633

1” 10304 P26341-1/4” 10305 P26351-1/2” 10306 P2636

2” 10307 P26372-1/2” 10308 P2638

3” 10309 P26394” 10310 P2638

��

www.bobdeansupply.comGateValves

F2882A Flanged Gate Valves - Milwaukee

2282A Iron Gate Valves. 125 lb. SWP - 200 lb. WOG. Non-rising stem. Solid wedge disc. Bolted bonnet. Gland packed. Flanged ends. Flanged shape and drilling to specification ASME B 16.1 (125 lb.). Milwaukee Valve.

F2885 Flanged Gate Valves

F2885M Iron Flanged Gate Valves. 125 lb. SWP - 200 lb. WOG. OS and Y. Solid wedge disc. Bolted bonnet. Gland packed. Flanged ends. Flange shape and drilling to specification ASME B 16.1 (125 lb.). Milwaukee Valve.

Size A B C D E Part No.

2” 7.00 12.00 7.00 6.00 0.63 P21402-1/2” 7.50 13.25 7.00 7.00 0.69 P2141

3” 8.00 13.50 8.00 7.50 0.75 P21424” 9.00 17.00 10.00 9.00 0.94 P21435” 10.00 18.00 12.00 10.00 0.94 P21446” 10.50 22.00 12.00 11.00 1.00 P21458” 11.50 26.50 14.00 13.50 1.13 P2146

10” 13.00 30.00 16.00 16.00 1.19 P214712” 14.00 35.00 18.00 19.00 1.25 P2148

Size A B C D E Part No.

2” 7.00 15.00 7.00 6.00 0.63 P21492-1/2” 7.50 16.88 8.00 7.00 0.69 -

3” 8.00 18.75 8.00 7.50 0.75 P21364” 9.00 22.75 10.00 9.00 0.94 -5” 10.00 27.13 10.00 10.00 0.94 -6” 10.50 30.13 12.00 11.00 1.00 P21778” 11.50 40.13 14.00 13.50 1.13 -

10” 13.00 48.25 16.00 16.00 1.81 -12” 14.00 56.88 18.00 19.00 1.25 -




Date post:	11-Apr-2018
Category:	Documents
Upload:	vunhan
View:	227 times
Download:	1 times

Pipe Fittings & Valves - Bob Dean ... Fittings & Valves Manufacturers & Vendors American Anvil...

Documents