Index
CAN and transponder interface (no key required) for Fiat 500 cars. Features include door trigger sensing, trunk/hatch pin, brake
status, handbrake status and tach output.
® Fiat is registered trademarks and property of their respective companies.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
Vehicle Application Guide...................................................................................................................................................
How to use Electronic Code for Immobilizer Bypass..........................................................................................................
Loop immobilizer for 2014-up vehicles...............................................................................................................................
InstallationWiring Diagram...................................................................................................................................................................
ProgrammingModule Programming.........................................................................................................................................................Module Reset.....................................................................................................................................................................Hard Reset.........................................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Limited One-Year Consumer Warranty...............................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
03
04
050606
07
08
09
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Page 2
Vehicle Application Guide
The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicles
2015
2014
2013
2012
2011
PK
-Im
mobilizer
Bypass-D
ata
No
Key
Req'd
*
CC
-Rear
Win
dow
Defo
gger
Activ
atio
n
Code
Entr
y
DL-T
runk
/H
atc
hR
ele
ase
FO
B-C
ontr
olo
fafterm
ark
etala
rmw
ithO
EM
rem
ote
RS
-Tach
/R
PM
Outp
ut
SS
-Entr
yM
onito
ring
ALL
Door
Pin
s
SS
-Entr
yM
onito
ring
Driver
Door
Pin
SS
-Entr
yM
onito
ring
Tru
nk/H
atc
hP
in
ST
-Bra
ke
Sta
tus
(footbra
ke)
ST
-E-B
rake
Sta
tus
ST
-Igniti
on
Sta
tus
ST
-Keysense
Sta
tus
Fiat
500 • • • • • • • D • D D • • D
500 Turbo ** • • • • • • D • D D • • W D D
Abarth ** • • • • • • D • D D • • W D D
Legend:
D: Data-to-Data (D2D) only CC: Comfort & Convenience Controls
W: Wire-to-Wire (W2W) only DL: OE Door Lock & Alarm Controls
•: D2D and W2W FOB: Sync CAN Interface w / FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Warning: Will not control OEM alarm.
* For Immobilizer Bypass-Data it is necessary to introduce Electronic Code 5-digit (see next page). ** No Bypass - for Comfort and Convenience only. One key is required for the installation.
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
CODECODEELECTRONIC CODE
MECHANICAL CODE
X . X . X . X . XX . X . X . X . X
Electronic Code 5-digit can be found on the card that comes with the car:
After the flashing was successful, a pop-up window will appear.
The module must be flashed only online on www.directechs.com
If the card is missing or can not be found, the Electronic Code can be obtained from an authorized dealer
Now you must enter Electronic Code 5-digit and click save.
NOTE: Electronic Code 5-digit can be changed only by flashing the module again .
Step 1: Finding Electronic Code 5-digit
How to use Electronic Code for Immobilizer Bypass
Step 2: Flashing the module and code entry
Page 3
30
86 8587
87a
(-) GWR (Status)from Remote Starter
(+) 12V
4-6turns
OEMImmobilizer
Receiver
Key wrap for 2014-up vehicles · Make 4-6 loops and place them as close to the front of ignition cylinder (OEM Immobilizer Receiver) as possible.· Test and secure mounted loops before reassembling the vehicle.· Make 4-6 loops and place them around the front of the plastic body of the vehicle’s coded key as shown below.
Not required in D2D mode.
FT CAN High HS CAN High
TX
(-) GroundRX
(+)12v
30
86 8587
87a
(-) Ground
30
30
OBII Diagnostic connector
Page 4
10
RF
Prog. Button
LED
4
14
12
2
DBALL/DBALL2
[2] Connect these wires only on manual transmission vehicle only.
[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
Resistor 1k W
Lock/Unlock: Violet/Red, pin 51
1
1
8
8
9
9
16
16
C4 conn.
7: Pink/White: (+) Parking Lights Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
4: White/Violet: (-) Aux 1
(+) 12v
FTCAN High: Orange/Green: 5
HSCAN High: Tan/Black: 3
FTCAN Low: Orange/Brown: 6
Hazard: Dk. Green/Red,
pin 7
HSCAN Low: Tan: 4
(-) Ground: Brown: 7
(+) 12V: Red: 13
(-) Ground: Black: 14
[1](AC) Tach Output: Violet/White: 5
(-) Hazard Output: Green/Black: 2
(-) Unlock: Orange/Black: 11
(+) Brake Input
(-) Trunk Release Output
(+) Ignition Output
(+) Ignition 2 Output
(+) Accessory Output
(+) Starter Output
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
(-) Ground
(+) 12 V
(-) Ground
(+) Parking Lights Output
(-) Rear Defogger Output
(-) Lock Output
(-) Unlock Output
[1](AC) Tach Input
(-) Trunk Status Input
(-) Hood Status Input
(-) Door Status Input
[2] (-) E-Brake Status Input
P#: XKD2D65
(-) Ground
Front of BCM
Back of BCM
Lock Output (conn. side): Yellow: 8
8: Violet: (+) Start Input
9: Pink: (+) Ignition Input
10: Blue/White: (-) GWR (Status) Input
(-) GWR (Status)
(+) Ignition Output
(+) Ignition 2 Output
(+) Accessory Output
(+) Start Output
(-) Start Output [2]
C4 Brown conn.Back of BCM
Diagnosticconnector
(OBD2)
C1 Conn.
C5 Conn.
C1
C5
Violet
Bro
wn
/Bla
ck, p
in 3
Vio
let/
Re
d,
pin
2
Trunk Release:Violet, pin 30
Wire Side View BUN!!!!
Rem
ote
Sta
rter
Lock Output (veh. side): Orange/Yellow: 9
[2](-) E-Brake Output: Black/White: 1
B-CAN High: Blue, pin 1
pin 1: Blue
C-CAN High: Green, pin 6
(Located underdriver side dash)
(Located underdriver side dash)
pin 6: Green
(+) Brake Output: Gray: 6
(-) Hood Status Output: Blue/Red: 12
pin 9: White FT CAN Low
C-CAN Low:Brown, pin 14
pin 14: BrownHS CAN Low
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
11
11
9
9
12
12
15
15
14
14
10
10
13
13
28
28
29
29
31
31
32
32
26
26
22
22
25
25
21
21
20
20
19
19
18
18
17
17
16
16
27
27
23
23
24
24
Manual Transmission Only [2]
21 3
Clutch Peda(M/T Only)
Clutch Switch
30
86 8587
87a(+) 12V
B-CAN Low:White, pin 9
Wiring Diagram
Note for me from Fred:- relay pin 87a to BCM - PIN 30 to car side violet wire
OBDII Diagnostic connector
8
16
1
9
Ignition Switch
3086 85
87
87a
Trunk Release:Violet, pin 30
Trunk Release:Violet
(+)12V
30
Refer to www.directechs.com for more information on vehicle-specific connections.
Wire jump template
60 5256 4859 5155 47
45 3741 3344 3640 32
30 2226 1829 2125 17
15 711 314 610 2
58 5054 4657 4953
43 3539 3142 3438
28 2024 1627 1923
13 59 112 48
60
52
56
48
59
51
55
47
45
37
41
33
44
36
40
32
30
22
26
18
29
21
25
17
15
7
11
3
14
6
10
2
58
50
54
46
57
49
53
43
35
39
31
42
34
38
28
20
24
16
27
19
23
13
5
9
1
12
4
8
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Page 5
2
3
4
Turn the ignition ON.
The green LED turns ON for 3 seconds and shuts off.
Turn the ignition OFF.
&
Solid x3 secs OFF
Key
Key Out
OF
F
START
IGN
OF
F
START
IGN
You have successfully completed the module programming sequence.
ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning! To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit available functions and features.
1. Connect the interface module to your computer using the XKLoader.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.directechs.com. The detail of the platform and firmware that is currently saved on the interface module will be indicated in the top right corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select Flash Standard install, and follow the instructions provided on the screen.5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”You can now proceed with the programming instructions below.
Refer to the LED Diagnostics section on page 7 for more information and for troubleshooting purposes.
1Solid
Wait until the LED turns ON solid red.
Note: To skip the transponder programming and use convenience features only, press the programming button 5 times.
OR
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
D2D Installation
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
10-pinD2D
st1
12-pin14-pin
nd2
rd3
10-pinD2D
st1
th4
12-pin14-pin
nd2
rd3
Module Programming
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
2
Solid
&
Solid Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
Module Reset
Hard Reset
2 & &Solid SolidRelease
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.
Page 6
1 OR
If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
W2W Installation
10-pinD2D
st1
12-pin14-pin
nd2
th4
rd3
10-pinD2D
st1
th5
12-pin14-pin
nd2
rd3
th4
No feature programming are available for this firmware.
Feature Programming
LED Diagnostics and Troubleshooting
Flashes
Flashes
Flashes x1
Flashes x2
Flashes x3
Off
LED Status Description Troubleshooting
Solid red.Waiting for the vehicle to be started.
Solid red for 30 seconds,then flashes once
Flashes Red twice
Flashes Red once
FT CAN not detected.
IMMO data not detected.
HS CAN not detected.
The B-CAN wires may be incorrectly connected. Refer tothe wiring diagram to make the right connections.
The IMMO wires may be incorrectly connected. Refer tothe wiring diagram to make the right connections.
The CAN wires may be incorrectly connected. Refer tothe wiring diagram to make the right connections.
Solid red for 30 seconds,then flashes 3 times.
Invalid CAN network.The CAN bus was detected but the ignition on CANmessage is not detected. Check if the firmware from unit is correct.
Flashes greencontinuously.
Flashes greencontinuously.
Vehicle has been successfullydetected. N/A.
Solid green for 3 seconds.Module has been successfullyprogrammed. N/A.
Ground out (GWR) is active.
Off. N/A.
Flashes green once.Lock command has beenreceived.
Flashes green twice.Unlock command has beenreceived.
Flashes green 3 times.Trunk release command hasbeen received.
Solid x30 secs
Flashes x1
Flashes x1
Solid x30 secs
Flashes x3
Flashes x2
Solid x3 secs
Solid
Inactive Ground While Running
Active Ground While Running
Module Programming
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
If it does not flash, the bypass module did not receive thesignal. Verify the connections between the bypass andthe remote starter module.
The Ground While Running (status) wire is incorrectlyconnected. Refer to the wiring diagram to make the right connections.
Make sure that all the connections are correct (see install sheet) and turn the ignition ON to begin the programming sequence.
Page 7
Otherwise, the GWR (Status) signal was lost or was never received by the module. Commands can come from RF, D2D or W2W.
LED Status Description TroubleshootingModule Programming
Off Module has no power. Check the power connections.
Solid redModule is powered. Waiting for
programming to begin.
Make sure that all the connections are correct (see
wiring diagram) and turn the ignition ON to begin the
programming sequence.
Solid red for 30 seconds
then flashes x 1.Invalid CAN network.
The CAN bus was detected but the ignition on CAN
message is not detected. Check if the firmware from
unit is correct.
Solid red for 30 seconds,
then flashes x 3.FT CAN not detected.
The B-CAN wires may be incorrectly connected. Refer
to the wiring diagram to make the right connections.
Flashes green
continuously.
Vehicle has been successfully
detected.Normal operation
Solid green for 3 secondsModule was successfully
programmed with transponder.Normal operation
Module Programming - Error codes
Flashes red x 1 HS CAN not detected.The C-CAN wires may be incorrectly connected. Refer
to the wiring diagram to make the right connections.
Flashes red x 2 IMMO data not detected.The IMMO wires may be incorrectly connected. Refer to
the wiring diagram to make the right connections.
Active Ground While Running
Flashes greenGROUND OUT ON (GWR)
command received.
Otherwise, the Ground While Running (s tatus) signal
was lost or was never received by the module.
Commands can come from RF, D2D or W2W.
D2D and W2W Commands
Flashes green x 1 LOCK command received.
Flashes green x 2 UNLOCK command received.
Flashes green x 3 TRUNK command received.
Normal operation
Solid
Solid redx30 secthen flashes x1
Solid redx30 secthen flashes x3
Solidgreenx3 sec
Flashesgreen
Flashesgreen
Flashesgreen x1
Flashesgreen x2
Flashesgreen x3
Off
Flashesred x1
Flashesred x2
Flashesred, red,orange
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Page 8
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent: 2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited One Year Consumer Warranty
Rev.: 20150921
Platform: DBALL/DBALL2Firmware: FIAT1
© 2015 Directed. All rights reserved.
Quick Reference Guide
© 2015 Directed. All rights reserved.
Button(s) Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runt ime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more information.
Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.
Notes
DBALL/DBALL2-FIAT1
�佒L �� A�
佃 呅剆
G畩摥猠�慮�楳�楳灯湩扬敳甠睷w�摡瑡汩湫�潭
块 偐佒
W��T�����单 T A畴潭潴楶攠D慴愠S潬畴楯湳 I湣����
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution