Plug fans with EC motor 07/2006
The engineer’s choice
2
Plug fans with EC motor
3
Text for tenders 6
EC centrifugal fans / Modules Ø 250 - Ø 450 8
Pre-selection / Mounting options 4
Accessories (inlet rings, air intake guard grilles) 22
Pressure control 24
Distributors, agencies and subsidiaries 26
Table of content
4
Pre-selection:
Fan installation:
[m³/h]
[Pa]
1000 2000 3000 4000 5000500200 300 400
100
1000
R3G 250 with M3G 084-DFR3G 280 with M3G 084-FAR3G 310 with M3G 112-EAR3G 355 with M3G 112-EAR3G 355 with M3G 150-FFR3G 400 with M3G 150-FFR3G 450 with M3G 150-FF
EC centrifugal fans / Modules with 2D-impellers
dh Hydraulic diameter dh = 2 . W . H / (W + H)
W Width of box
H Height of box
D Outer diameter of fan
W
H D
The graph shows the reduction in air flow if thefan is mounted in a rectangular box.
1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0
dh/D
Corr
ectio
n fa
ctor
for a
ir flo
w
1,00
0,99
0,98
0,97
0,96
0,95
0,94
0,93
0,92
5
Mounting options:
1.) AHU set-up with fan unitmounted in structure-bornenoise absorbend way,anti-vibration mounted
Muffling backdrop Preliminary filter suction-side Fan receptacle and base constructionseparating plate with structure-borne noise absorption(*)
flexible air-intake nozzle Muffling backdrop
Mounting plate with Muffling backdropstructure-borne noise absorption(*)
Mounting plate with structure-borne noise absorption(*)
Muffling backdrop
(*) = provided by customer
2a.) Centrifugal fan / Module for direct installation onmounting plate with structure-borne noise absorptionand anti-vibration mount (horizontal air flow)
2b.) Centrifugal fan / Module for direct installationon mounting plate with structure-borne noiseabsorption and anti-vibration mount(vertical air flow)
6
Text for tenders
EC centrifugal fansR3G 250 to R3G 450
ebm-papst high performance centrifugal fans
Single inlet; direct drive; 2D centrifugal impeller mounted on an electro-
nically commutated external-rotor motor with integrated electronics;
backward curved impeller blades; inlet nozzle made of galvanised sheet
steel; complete unit statically and dynamically balanced in two
planes according to DIN / ISO 1940 and to balancing quality G 6.3;
EC external-rotor motor with maintenance-free ball bearings and
permanent lubrication; wide voltage input 200-277V, 50/60 Hz
respectively 380-480V, 50/60Hz; unit can be operated on all standard
Electricity Board networks at identical air performance; optimised motor
technology; soft start; integrated current limitation; connection via
brought-out variable cable connector (motor size 084) or via
easy-to-mount and robust integrated terminal box made of aluminium
with spring loaded terminals (motor sizes 112 and 150); extremely
compact electronics; with adjustable PID controller (motor sizes 112 and
150); meets all necessary EMC directives and all requirements as to
current reverse transfer; no complicated installation with shielded cables
required; very low-noise commutation logic; 100% controllability.
For technical details, dimensions and connection -
see data sheet
Protective features
- Alarm relay with zero-potential change-over contacts
(250 V AC/2 A, cos ϕ = 1)
- Locked-rotor protection
- Phase failure detection
- Soft start of motors
- Mains under-voltage detection
- Over-temperature protection of electronics and motor
- Short-circuit protection
Approvals
UL, CSA, VDE, CE, CCC and GOST
Technical Data
- Air flow V = __________m3/h
- Static pressure ∆PF = __________Pa
- Voltage range U = V
- Frequenzy f = Hz
- Fan speed n = __________min-1
- Power input P1 = __________kW
- Current input I = __________A
- Noise level LP = __________dBA
- Perm. ambient temperature t = °C
- Fan mass = __________kg
- Direction of rotation = clockwise
Fan type
_______________________________
7
Text for tenders
EC Centrifugal fan modulesK3G 250 to K3G 450
ebm-papst high performance centrifugal fan modules
Single inlet; direct drive; 2D centrifugal impeller mounted on an electro-
nically commutated external-rotor motor with integrated electronics;
backward curved impeller blades; inlet nozzle made of galvanised sheet
steel with pressure relief; complete unit statically and dynamically
balanced in two planes according to DIN / ISO 1940 and to balancing
quality G 6.3; EC external-rotor motor with maintenance-free ball bea-
rings and permanent lubrication; wide voltage input 200-277V, 50/60 Hz
respectively 380-480V, 50/60Hz; unit can be operated on all standard
Electricity Board networks at identical air performance; optimised motor
technology; soft start; integrated current limitation; connection via
brought-out variable cable connector (motor size 084) or via easy-to-
mount and robust integrated terminal box made of aluminium with
spring loaded terminals (motor sizes 112 and 150); extremely compact
electronics; with adjustable PID controller (motor sizes 112 and 150);
meets all necessary EMC directives and all requirements as to current
reverse transfer; no complicated installation with shielded cables requi-
red; very low-noise commutation logic; 100% controllability.
For technical details, dimensions and connection -
see data sheet
Complete unit is installed into customer Base construction needs to beunit in anti-vibration mounted state. provided for in customer con-
struction to guarantee structure-borne noise absorption.
K3G 250-AR39 -72 K3G 250-AR39 -71K3G 280-AJ33 -72 K3G 280-AJ33 -71K3G 310-AV52 -02 K3G 310-AV52 -01K3G 355-AT56 -02 K3G 355-AT56 -01K3G 355-AV13 -03 K3G 355-AV13 -04K3G 400-AS12 -03 K3G 400-AS12 -04K3G 450-AS06 -03 K3G 450-AS06 -04
Protective features
- Alarm relay with zero-potential change-over contacts
(250 V AC/2 A, cos ϕ = 1)
- Locked-rotor protection
- Phase failure detection
- Soft start of motors
- Mains under-voltage detection
- Over-temperature protection of electronics and motor
- Short-circuit protection
Approvals
UL, CSA, VDE, CE, CCC and GOST
Technical data
- Air flow V = __________m3/h
- Static pressure ∆PF = __________Pa
- Voltage range U = V
- Frequenzy f = Hz
- Fan speed n = __________min-1
- Power input P1 = __________kW
- Current input I = __________A
- Noise level LP = __________dBA
- Perm. ambient temperature t = °C
- Fan mass = __________kg
Fan type
_______________________________
providedby
customer
Characteristics
400 800 1200 1600 2000
0 [CFM]250 500 750 1000 1250
[Pa]
200
400
600
800
1000
[in H
2O]
1,6
2,4
3,2
4,0
0,8
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
1
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 250
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Cable exit: variable- Technical features: control input 0-10 VDC / PWM, alarm relay,
10 V voltage output for potentiometer- Direction of rotation: clockwise, seen on rotor- Type of protection: IP 44- Approvals: UL, CSA, VDE, CE, CCC and GOST- Mounting position: at will
ebm-papst · Mulfingen
8
n[min-1]
P1
[W]
1
2
3
4
ηηtL
[%]LpA
[dBA]
5
6
7
8
I[A]
n[min-1]
P1
[W]
9
ηηtL
[%]LpA
[dBA]I
[A]
10
11
121
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 250-AR39 -71
K3G 250-AR39 -72
K3G 250-AR39 -71
Motor
M3G084-DF
M3G084-DF
M3G084-DF
VAC Hz min-1 W A °C kg
200-277 50/60 3090 460 3.0 -25..+40 4.4
200-277 50/60 3090 460 3.0 -25..+40 9.0
200-277 50/60 3090 460 3.0 -25..+40 10.0
subject to alterations
1
1
1
Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Nominal data Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
3220 419
455
448
257
279
275
268
79
75
73
71
75
71
69
67
437
2740
2,7
2,9
2,9
2,8
1,7
1,8
1,8
1,7
2260
3100
2630
2170
3120
2650
2190
3190
2710
2230
144 0,9
1,0
1,0
1,0
156
154
150
71
70
69
67
---
50
58
50
---
50
58
50
---
50
58
50
9
Type
R3G 250-AR39 -71
K3G 250-AR39 -72
K3G 250-AR39 -71
Inlet ring
25040-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
R3G 250-AR39 -71
K3G 250-AR39 -72K3G 250-AR39 -71
183±3
135±2
Ø259
Ø176
11280
Ø178
Ø150
±0,
25
Ø100
48130±1
Ø102
40
Ø167
,7
Ø290
Ø260
4 x
4,5
45˚
4x90
˚
Ø164±0,35
M6
600+
20
5
215,5168 2,5
400300
4 x
Ø 11
350
-1±3
±2215,5
30 168 2,5
15
3 x
8040
8 x
Ø 7
400320
4 x
Ø 11
350
-1
-1
±3
±2
L PEN
Line Signal Colour Assignment / function Line Signal Colour Assignment / function1 2L black Mains 50/60 Hz, phase +10 V red
0-10 V / PWM yellow Control inputN blue Mains 50/60 Hz, neutral
PE green/Yellow Protective earth
NC white1 Alarm relay, normally closed
COM white2 Alarm relay, COMMON
Line 1
black green/yellowblue
+10
V
0-10
VPW
M
Line 2
red yellow
Voltage output +10 V max. 1.1 mA
GND blue GND
NC GND
white1
COM
white2 blue
Electrical connection:
Depth of screwmin. 8 mm, max. 10 mm
Number of blades = 7
Characteristics
500 1000 1500 2000 2500 3000
0 [CFM]250
[Pa]
100
200
300
400
500
600
700
[in H
2O]
0,8
1,2
1,6
2,0
2,4
2,8
800 3,2
900
0,4
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
1500 750 1000 1250 1500 1750
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 280
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Cable exit: variable- Technical features: control input 0-10 VDC / PWM, alarm relay,
10 V voltage output for potentiometer- Direction of rotation: clockwise, seen on rotor- Type of protection: IP 44- Approvals: UL, CSA, VDE, CE, CCC and GOST- Mounting position: at will
ebm-papst · Mulfingen
10
2730 436
484
493
267
297
303
283
n[min-1]
P1
[W]
1
2
3
4
77
74
72
74
73
68
67
68
ηηtL
[%]
460
2320
LpA
[dBA]
5
6
7
8
2,8
3,1
3,2
3,0
1,7
1,9
1,9
1,8
I[A]
1910
2620
2220
1830
2610
2220
1830
2680
2280
1880
149
n[min-1]
P1
[W]
9
ηηtL
[%]LpA
[dBA]
1,0
1,1
1,1
1,0
I[A]
16610
16911
15812
69
63
61
62
---
60
67
60
---
60
67
60
---
60
67
601
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 280-AJ33 -71
K3G 280-AJ33 -72
K3G 280-AJ33 -71
Motor
M3G084-FA
M3G084-FA
M3G084-FA
VAC Hz min-1 W A °C kg
200-277 50/60 2610 500 3.2 -25..+40 5.4
200-277 50/60 2610 500 3.2 -25..+40 10.0
200-277 50/60 2610 500 3.2 -25..+40 11.0
subject to alterations
1
1
1
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
234,530 187 2,5
15
3 x
8040
8 x
Ø 7
400320
4 x
Ø 11
350
-1
-1
±3
±2
234,5187 2,5
400300
4 x
Ø 11
350
-1±3
±2
11
Type
R3G 280-AJ33 -71
K3G 280-AJ33 -72
K3G 280-AJ33 -71
Inlet ring
28040-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
197±3
149±2
Ø284
Ø197
,4
12690
Ø178
Ø150
±0,
25
Ø100
48145±1
Ø102
45
Ø186
,4
Ø325
Ø280
4 x
4,5
45˚
4x90
˚
Ø164±0,35
M6
600+
20
5
R3G 280-AJ33 -71
K3G 280-AJ33 -72K3G 280-AJ33 -71
L PEN
Line Signal Colour Assignment / function Line Signal Colour Assignment / function1 2L black Mains 50/60 Hz, phase +10 V red
0-10 V / PWM yellow Control inputN blue Mains 50/60 Hz, neutral
PE green/Yellow Protective earth
NC white1 Alarm relay, normally closed
COM white2 Alarm relay, COMMON
Line 1
black green/yellowblue
+10
V
0-10
VPW
M
Line 2
red yellow
Voltage output +10 V max. 1.1 mA
GND blue GND
NC GND
white1
COM
white2 blue
Electrical connection:
Depth of screwmin. 8 mm, max. 10 mm
Number of blades = 7
Characteristics
1000 2000 3000 4000
0 [CFM]500
[Pa]
200
400
600
800
[in H
2O]
1,6
2,4
3,2
0,8
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
11000 1500 2000 2500
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 310
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Technical features: control input 0-10 VDC / PWM, RS485 ebmBUS,alarm relay, integrated PID control, voltage supply for sensor,input for sensor 0-10 V respectively 4-20 mA, 0-10 V ouptut for slave, PFC (passive),soft start, line undervoltage detection, phase failure detection, motor current limitation,over-temperature protected electronics and motor, locked-rotor protection
- Type of protection: IP 54 according to DIN VDE 0470, part 1 (EN 60 529) category 2- Approvals: UL, CSA, VDE, CE, CCC and GOST are applied for- Mounting position: at will
ebm-papst · Mulfingen
12
2640 771
935
994
473
574
611
611
n[min-1]
P1
[W]
1
2
3
4
81
79
76
75
77
74
72
70
ηηtL
[%]
994
2240
LpA
[dBA]
5
6
7
8
1,5
1,7
1,8
1,8
0,9
1,1
1,1
1,1
I[A]
1850
2640
2240
1850
2640
2240
1850
2640
2240
1850
264
n[min-1]
P1
[W]
9
ηηtL
[%]LpA
[dBA]
0,5
0,6
0,6
0,6
I[A]
32110
34111
34112
71
70
67
65
---
49
60
59
---
49
60
59
---
49
60
591
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 310-AV52 -01
K3G 310-AV52 -02
K3G 310-AV52 -01
Motor
M3G112-EA
M3G112-EA
M3G112-EA
3~ VAC Hz min-1 W A °C kg
380-480 50/60 2640 1000 1.9 -25..+50 8.9
380-480 50/60 2640 1000 1.9 -25..+50 15.4
380-480 50/60 2640 1000 1.9 -25..+50 15.9
subject to alterations
1
1
1
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
13
Type
R3G 310-AV52 -01
K3G 310-AV52 -02
K3G 310-AV52 -01
Inlet ring
31060-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
6
226,5±3
170±256,5160,5±1
146100
Ø319
Ø222
51
4 x
4,5
Ø210
,2
Ø365
Ø325
5x72˚5 x M6
Ø186±0,5
Ø200
Ø168
±0,
5 R3G 310-AV52 -01
K3G 310-AV52 -02K3G 310-AV52 -01
Cable gland
300
350
4 x
Ø 11
400211 15
267,5 -1±3
±2267,5
30 211 15
3 x
8040
8 x
Ø 9
15
400320
4 x
Ø 11
350
-1
-1
±3
±2
RS A
RS B
RS A
RS B
GND
0-10
VPW
M
4-20
mA
+20
V
+10
V
0-10
VPW
M
GND
OUT
NO COM
NC L1 L2 L3 PE PE
Connector Signal Pin No. Assignment / function Connector Signal Pin No. Assignment / functionPE KL3PE --- Protective earth OUT 1 Master output 0-10 V max. 3 mA
KL1 L3, L2, L1 1, 2, 3 Mains; L3, L2, L1 GND 2, 8 GND
KL2 1 0-10 V / PWM 3, 7 Control / Actual value input
COM 2 Alarm relay, COMMON +10 V 4 Supply for external potentiometer 10 mA
3 +20 V 5 Supply for external sensor 50 mA
4-20 mA 6 Control / Actual value input
RS B 9, 11 RS485 interface for ebmBUS; RS B
RS A 10, 12 RS485 interface for ebmBUS; RS A
Electrical connection:
12
KL3 KL2 KL1 PE
11 10 9 8 7 6 5 4 3 2 1 3 2 1 3 2 1
NC Alarm relay, normally closed
NO Alarm relay, normally open
Depth of screwmin. 12 mm, max. 16 mm
Number of blades = 7
Characteristics
1000 2000 3000 4000 5000
0 [CFM]500
[Pa]
100
200
300
400
500
600
700
1,2
[in H
2O]
1,6
2,0
2,4
2,8
0,8
0,4
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
11000 1500 2000 2500 3000
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 355
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Technical features: control input 0-10 VDC / PWM, RS485 ebmBUS,alarm relay, integrated PID control, voltage supply for sensor,input for sensor 0-10 V respectively 4-20 mA, 0-10 V ouptut for slave, PFC (passive),soft start, line undervoltage detection, phase failure detection, motor current limitation,over-temperature protected electronics and motor, locked-rotor protection
- Type of protection: IP 54 according to DIN VDE 0470, part 1 (EN 60 529) category 2- Approvals: UL, CSA, VDE, CE, CCC and GOST are applied for- Mounting position: at will
ebm-papst · Mulfingen
14
2200 739
932
996
454
572
612
587
1
2
3
4
83
80
77
77
78
75
72
71
957
18705
6
7
8
1,4
1,7
1,9
1,8
0,9
1,1
1,1
1,1
1540
2200
1870
1540
2200
1870
1540
2200
1870
1540
2539 0,5
0,6
0,6
0,6
32010
34211
32812
73
70
67
65
---
58
67
64
---
58
67
64
---
58
67
641
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 355-AT56 -01
K3G 355-AT56 -02
K3G 355-AT56 -01
Motor
M3G112-EA
M3G112-EA
M3G112-EA
3~ VAC Hz min-1 W A °C kg
380-480 50/60 2200 1000 1.9 -25..+50 9.1
380-480 50/60 2200 1000 1.9 -25..+50 17.0
380-480 50/60 2200 1000 1.9 -25..+50 19.0
subject to alterations
1
1
1
n[min-1]
P1
[W]ηηtL
[%]LpA
[dBA]I
[A]n
[min-1]P1
[W]ηηtL
[%]LpA
[dBA]I
[A]
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
292,530 236 15
3 x
100
608
x Ø
9
15
500420
4 x
Ø 11
450
-1
-1
±3
±2 380
450
4 x
Ø 11
500236 15
292,5 -1±3
±2
15
Type
R3G 355-AT56 -01
K3G 355-AT56 -02
K3G 355-AT56 -01
Inlet ring
35540-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
6
243,5±3
187±256,5160,5±1
164112
Ø360
Ø250
,3
59,5
4 x
4,5
Ø236
,6
Ø412
Ø345
5x72˚5 x M6
Ø186±0,5
Ø200
Ø168
±0,
5 R3G 355-AT56 -01
K3G 355-AT56 -02K3G 355-AT56 -01
Cable gland
RS A
RS B
RS A
RS B
GND
0-10
VPW
M
4-20
mA
+20
V
+10
V
0-10
VPW
M
GND
OUT
NO COM
NC L1 L2 L3 PE PE
Connector Signal Pin No. Assignment / function Connector Signal Pin No. Assignment / functionPE KL3PE --- Protective earth OUT 1 Master output 0-10 V max. 3 mA
KL1 L3, L2, L1 1, 2, 3 Mains; L3, L2, L1 GND 2, 8 GND
KL2 1 0-10 V / PWM 3, 7 Control / Actual value input
COM 2 Alarm relay, COMMON +10 V 4 Supply for external potentiometer 10 mA
3 +20 V 5 Supply for external sensor 50 mA
4-20 mA 6 Control / Actual value input
RS B 9, 11 RS485 interface for ebmBUS; RS B
RS A 10, 12 RS485 interface for ebmBUS; RS A
Electrical connection:
12
KL3 KL2 KL1 PE
11 10 9 8 7 6 5 4 3 2 1 3 2 1 3 2 1
NC Alarm relay, normally closed
NO Alarm relay, normally open
Depth of screwmin. 12 mm, max. 16 mm
Number of blades = 7
Characteristics
1000 2000 3000 4000 5000
0 [CFM]500
[Pa]
200
400
600
800
1000
1200
2,4
[in H
2O]
3,2
4,0
4,8
1,6
0,8
[m3/h]
1
2
5
6
7
8
10
1112
9
3
4
11000 1500 2000 2500 3000
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 355
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Technical features: control input 0-10 VDC / PWM, RS485 ebmBUS,alarm relay, integrated PID control, voltage supply for sensor,input for sensor 0-10 V respectively 4-20 mA, 0-10 V ouptut for slave, PFC (passive),soft start, line undervoltage detection, phase failure detection, motor current limitation,over-temperature protected electronics and motor, locked-rotor protection
- Type of protection: IP 54 according to DIN VDE 0470, part 1 (EN 60 529) category 2- Approvals: UL, CSA, VDE, CE, CCC and GOST- Mounting position: at will
ebm-papst · Mulfingen
16
Type
R3G 355-AV13 -03
K3G 355-AV13 -03
K3G 355-AV13 -04
Motor
M3G150-FF
M3G150-FF
M3G150-FF
3~ VAC Hz min-1 kW A °C kg
380-480 50/60 2800 2.15 3.4 -25..+50 19.5
380-480 50/60 2800 2.15 3.4 -25..+50 30.0
380-480 50/60 2800 2.15 3.4 -25..+50 31.5
subject to alterations
1
1
1
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
2800 1,81
2,03
2,11
1,11
1,25
1,30
1,18
n[min-1]
P1
[kW]
1
2
3
4
85
83
83
83
81
79
79
79
ηηtL
[%]
1,91
2380
LpA
[dBA]
5
6
7
8
2,8
3,2
3,3
3,0
1,8
1,9
2,0
1,8
I[A]
1960
2800
2380
1960
2800
2380
1960
2800
2380
1960
0,62
n[min-1]
P1
[kW]
9
ηηtL
[%]LpA
[dBA]
1,0
1,1
1,1
1,1
I[A]
0,7010
0,7211
0,6612
77
79
79
79
---
51
57
56
---
51
57
56
---
51
57
561
1
1
1
1
1
1
1
1
1
1
1
259329
15
450
4 x
Ø11
380 500 -1±3
±2
17
Type
R3G 355-AV13 -03
K3G 355-AV13 -03
K3G 355-AV13 -04
Inlet ring
35540-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
210
280
219,5 ±1
70
164
112
6
360
250,
3ØØ
412
236,
6Ø
4,5
4xØ
Ø
Ø235-2
252
8xM10
±0,3
±2
±3 59,5
345
Ø 8x45
˚
R3G 355-AV13 -03
K3G 355-AV13 -03K3G 355-AV13 -04
3 x
100
608
x Ø
9
15
32930 259 15
4 x
Ø 11
450
500420
-1
-1
±3
±2
RS A
RS B
RS A
RS B
GND
0-10
VPW
M
4-20
mA
+20
V
+10
V
0-10
VPW
M
GND
OUT
NO COM
NC L1 L2 L3 PE PE
Connector Signal Pin No. Assignment / function Connector Signal Pin No. Assignment / functionPE KL3PE --- Protective earth OUT 1 Master output 0-10 V max. 3 mA
KL1 L3, L2, L1 1, 2, 3 Mains; L3, L2, L1 GND 2, 8 GND
KL2 1 0-10 V / PWM 3, 7 Control / Actual value input
COM 2 Alarm relay, COMMON +10 V 4 Supply for external potentiometer 10 mA
3 +20 V 5 Supply for external sensor 50 mA
4-20 mA 6 Control / Actual value input
RS B 9, 11 RS485 interface for ebmBUS; RS B
RS A 10, 12 RS485 interface for ebmBUS; RS A
Electrical connection:
12
KL3 KL2 KL1 PE
11 10 9 8 7 6 5 4 3 2 1 3 2 1 3 2 1
NC Alarm relay, normally closed
NO Alarm relay, normally open
Depth of screwmax. 25 mm
Number of blades = 7
Cable gland M 20
Characteristics
2000 4000 6000 8000
0 2000 3000 [CFM]1000 4000
[Pa]
200
400
600
800
1000
1200
1400
2,4
[in H
2O]
3,2
4,0
4,8
5,6
1,6
0,8
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
1
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 400
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Technical features: control input 0-10 VDC / PWM, RS485 ebmBUS,alarm relay, integrated PID control, voltage supply for sensor,input for sensor 0-10 V respectively 4-20 mA, 0-10 V ouptut for slave, PFC (passive),soft start, line undervoltage detection, phase failure detection, motor current limitation,over-temperature protected electronics and motor, locked-rotor protection
- Type of protection: IP 54 according to DIN VDE 0470, part 1 (EN 60 529) category 2- Approvals: UL, CSA, VDE, CE, CCC and GOST- Mounting position: at will
ebm-papst · Mulfingen
18
2590 2,24
2,80
2,94
1,37
1,72
1,81
1,62
1
2
3
4
87
83
82
83
82
79
77
78
2,63
22005
6
7
8
3,6
4,6
4,8
4,3
2,2
2,8
2,9
2,6
1800
2590
2200
1800
2590
2200
1800
2590
2200
1800
0,779 1,2
1,6
1,6
1,5
0,9610
1,0111
0,9012
78
75
73
72
---
58
65
63
---
58
65
63
---
58
65
631
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 400-AS12 -03
K3G 400-AS12 -03
K3G 400-AS12 -04
Motor
M3G150-FF
M3G150-FF
M3G150-FF
3~ VAC Hz min-1 kW A °C kg
380-480 50/60 2590 2.95 4.8 -25..+50 20.5
380-480 50/60 2590 2.95 4.8 -25..+50 32.0
380-480 50/60 2590 2.95 4.8 -25..+50 33.5
subject to alterations
1
1
1
n[min-1]
P1
[kW]ηηtL
[%]LpA
[dBA]I
[A]n
[min-1]P1
[kW]ηηtL
[%]LpA
[dBA]I
[A]
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
19
Type
R3G 400-AS12 -03
K3G 400-AS12 -03
K3G 400-AS12 -04
Inlet ring
40040-2-4013 (with one pressure relief)
integrated
integrated
Accessoriesp. 22 f.
229
299
219,5 ±1
70
182
125
7
404
282
ØØ
464
267,
5Ø
96x
Ø
Ø
Ø235-2
252
8xM10
±0,3
±2
±3 66
390
Ø 8x45
˚
R3G 400-AS12 -03
283,5353,5
15
450
4 x
Ø11
380 500 -1
±2
±3
K3G 400-AS12 -03K3G 400-AS12 -04
3 x
100
608
x Ø
9
15
353,530 283,5 15
4 x
Ø 11
450
500420
-1
-1±2
±3
RS A
RS B
RS A
RS B
GND
0-10
VPW
M
4-20
mA
+20
V
+10
V
0-10
VPW
M
GND
OUT
NO COM
NC L1 L2 L3 PE PE
Connector Signal Pin No. Assignment / function Connector Signal Pin No. Assignment / functionPE KL3PE --- Protective earth OUT 1 Master output 0-10 V max. 3 mA
KL1 L3, L2, L1 1, 2, 3 Mains; L3, L2, L1 GND 2, 8 GND
KL2 1 0-10 V / PWM 3, 7 Control / Actual value input
COM 2 Alarm relay, COMMON +10 V 4 Supply for external potentiometer 10 mA
3 +20 V 5 Supply for external sensor 50 mA
4-20 mA 6 Control / Actual value input
RS B 9, 11 RS485 interface for ebmBUS; RS B
RS A 10, 12 RS485 interface for ebmBUS; RS A
Electrical connection:
12
KL3 KL2 KL1 PE
11 10 9 8 7 6 5 4 3 2 1 3 2 1 3 2 1
NC Alarm relay, normally closed
NO Alarm relay, normally open
Depth of screwmax. 25 mm
Number of blades = 7
Cable gland M 20
Characteristics
2000 4000 6000 8000 10000
0 [CFM]1000
[Pa]
200
400
600
800
1000
1200
2,4
[in H
2O]
3,2
4,0
4,8
1,6
0,8
[m3/h]
1
2
5
6
7
8
10
11
12
9
3
4
12000 3000 4000 5000 6000
EC centrifugal fans / Modulesbackward curved, with integrated electronics, Ø 450
- Material: stator and electronics housing made of die-cast aluminium, rotor made of sheet steel (enamelled in black), impeller made of sheet aluminium, galvanised sheet metal parts
- Technical features: control input 0-10 VDC / PWM, RS485 ebmBUS,alarm relay, integrated PID control, voltage supply for sensor,input for sensor 0-10 V respectively 4-20 mA, 0-10 V ouptut for slave, PFC (passive),soft start, line undervoltage detection, phase failure detection, motor current limitation,over-temperature protected electronics and motor, locked-rotor protection
- Type of protection: IP 54 according to DIN VDE 0470, part 1 (EN 60 529) category 2- Approvals: UL, CSA, VDE, CE, CCC and GOST- Mounting position: at will
ebm-papst · Mulfingen
20
2150 2,10
2,71
2,87
1,29
1,67
1,76
1,64
n[min-1]
P1
[kW]
1
2
3
4
88
86
81
80
83
80
76
75
ηηtL
[%]
2,67
1800
LpA
[dBA]
5
6
7
8
3,2
4,2
4,4
4,1
2,0
2,6
2,7
2,5
I[A]
1500
2150
1800
1500
2150
1800
1500
2150
1800
1500
0,72
n[min-1]
P1
[kW]
9
ηηtL
[%]LpA
[dBA]
1,1
1,4
1,5
1,4
I[A]
0,9310
0,9811
0,9212
77
74
71
69
---
55
71
64
---
55
71
64
---
55
71
641
1
1
1
1
1
1
1
1
1
1
1
Type
R3G 450-AS06 -03
K3G 450-AS06 -03
K3G 450-AS06 -04
Motor
M3G150-FF
M3G150-FF
M3G150-FF
3~ VAC Hz min-1 kW A °C kg
380-480 50/60 2150 2.90 4.5 -25..+50 21.5
380-480 50/60 2150 2.90 4.5 -25..+50 37.0
380-480 50/60 2150 2.90 4.5 -25..+50 39.5
subject to alterations
1
1
1
Nominal data Char
acte
ristic
Volta
ge ra
nge
Freq
uenc
y
Spee
d/rp
m
Perm
.am
b.te
mp.
Mas
s
Max
.po
wer
inpu
t
Max
.cu
rren
t dra
w
21
250,5
320,5
219,5 ±1
70
206,5
140
7
455
317
ØØ 522
301
Ø9
6xØ
Ø
Ø235-2
252
8xM10
±0,3
±2
±3 73,5
430
Ø 8x45
˚
Type
R3G 450-AS06 -03
K3G 450-AS06 -03
K3G 450-AS06 -04
Inlet ring
45040-2-4013 (with one pressure relief)
integrated
integrated
R3G 450-AS06 -03
Accessoriesp. 22 f.
312,5382,5
15
580
8 x
Ø11
550 630 -1
±2
±3
K3G 450-AS06 -03K3G 450-AS06 -04
3 x
120
708
x Ø
9
15
382,530 312,5 15
8 x
Ø 11
580
630500
-1
-1±2
±3
RS A
RS B
RS A
RS B
GND
0-10
VPW
M
4-20
mA
+20
V
+10
V
0-10
VPW
M
GND
OUT
NO COM
NC L1 L2 L3 PE PE
Connector Signal Pin No. Assignment / function Connector Signal Pin No. Assignment / functionPE KL3PE --- Protective earth OUT 1 Master output 0-10 V max. 3 mA
KL1 L3, L2, L1 1, 2, 3 Mains; L3, L2, L1 GND 2, 8 GND
KL2 1 0-10 V / PWM 3, 7 Control / Actual value input
COM 2 Alarm relay, COMMON +10 V 4 Supply for external potentiometer 10 mA
3 +20 V 5 Supply for external sensor 50 mA
4-20 mA 6 Control / Actual value input
RS B 9, 11 RS485 interface for ebmBUS; RS B
RS A 10, 12 RS485 interface for ebmBUS; RS A
Electrical connection:
12
KL3 KL2 KL1 PE
11 10 9 8 7 6 5 4 3 2 1 3 2 1 3 2 1
NC Alarm relay, normally closed
NO Alarm relay, normally open
Depth of screwmax. 25 mm
Number of blades = 7
Cable gland M 20
Accessories
22
k-value
67
87
108
141
161
225
Inlet rings with measuring device to determine air flow for backward curved centrifugal fans
Part no. Part no.
25040-2-4013(1) / 25030-2-4013(2)
28040-2-4013(1) / 28030-2-4013(2)
31060-2-4013(1) / 31040-2-4013(2)
35540-2-4013(1) / 35530-2-4013(2)
40040-2-4013(1) / 40030-2-4013(2)
45040-2-4013(1) / 45030-2-4013(2)
Size
250
280
310
355
400
450
For dimensions, see
page 9
page 11
page 13
page 15 / 17
page 19
page 21
subject to alterations(1)
with one pressure relief (2)
with ring pipe (measuring points)
6x60
˚
4x90˚
Part no.
25020-2-4013
28020-2-4013
31020-2-4013
35520-2-4013
40020-2-4013
45020-2-4013
Size
250
280
310
355
400
450
Vers.
1
1
1
1
2
2
For dimensions, see
page 9
page 11
page 13
page 15 / 17
page 19
page 21
subject to alterations
- Material: galvanised sheet steel
ebm-papst · Mulfingen
Inlet rings without measuring device for backward curved centrifugal fans
Vers. 1 Vers. 2
Air flow determination:
∆p W
0,5xD
D
The differential pressure approach compares the static pressure before the inlet ring with the static pressure inside the inlet ring. Air flow can be calculated on the basis of the differential pressure (difference in pressure ofthe static pressures) in keeping with the following equation:
V = k . �∆pW V in [m3/h] and ∆pW in [Pa]
If constant air flow is to be controlled to, then the nozzle pressure has to bekept constant:
∆pW = V2 / k2
k takes into account the specific nozzle characteristics.Differences in static pressure are measured in 1/4 measuring point(s) alongthe circumference of the inlet nozzle. Connection on the customer side isacomplished via a pre-mounted T tube connector. This tube connector issuited for pneumatic hoses with an internal diameter of 4 mm.
ebm-papst · Mulfingen
Accessories
23
a
e
Ød
be
Ød
b
a
Part no.
78129-2-4039
78130-2-4039
78131-2-4039
78132-2-4039
78133-2-4039
78134-2-4039
Size
250
280
310
355
400
450
Vers.
1
1
1
1
2
2
a b d e Strut pitch
260 4,5 191 2,8 4 x 90°
280 4,5 229 2,8 4 x 90°
325 4,5 248 2,8 4 x 90°
345 4,5 305 2,8 4 x 90°
390 8,5 343 3,8 3 x 120°
430 8,5 381 3,8 3 x 120°
subject to alterations
- Material: sheet steel, plastic coated,silver-metallic gloss
ebm-papst · Mulfingen
Air intake guard grilles for backward curved centrifugal fans (according to EN 294)
Vers. 1 Vers. 2
24
Pressure control with integrated pressure sensor
- Functions: integrated PID controller,Day/Night/Linear set point preset,integrated set point potentiometer for Day and Night,external set point preset via potentiometer
- Pressure sensor: 0-500 Pa, bursting strength 200 mbar,for non-aggressive gaseous media
- Type of protection: IP 55- Inlet rings: suitable inlet nozzle for airflow determination, see page 22
ebm-papst · Mulfingen
Type
CCC 000-AC04 -01
Nominal data
subject to alterations
195
180±0,4
7,5Ø5,5
10
125
43
10,51,5
115
95±
0,2
89,5
35,5
162
167
pressure controller IP55100-277 VAC 50/60 Hzpressure range 0-500 Pa
VAC Hz VDC Pa °C
100-277 50/60 20 @ 50 mA 50-500 -25..+60
Pres
sure
con
trol r
ange
Perm
.am
b.te
mp.
Nom
inal
vo
ltage
rang
e
Nom
inal
vol
tage
,al
tern
ativ
e
Freq
uenc
y
25
PE L N PE L N
ST1 ST2
NC COM
ST7
NC COM
ST8
20 V
IN
GND
ST3
Tach
o
OUT
GND
+10
V
0-10
VPW
M
GND
Day
GND
Nigh
t
GND
ST4
Linear
Connector Assignment / function
ST8
Relay contact for alarm
ST7
ST2
ST1
Connector Assignment / function
ST4
Selector switch terminal
Set value potentiometer
GND
ST3
GND
Signal
COM
Relay contact for alarm, break for failureNC
Relay contact for alarmCOM
Relay contact for alarm, break for failureNC
N
L
Mains 50/60 Hz, neutral
Mains 50/60 Hz, phase
Protective earthPE
N
L
Mains 50/60 Hz, neutral
Mains 50/60 Hz, phase
Protective earthPE
Signal
GND
Selector switch terminalNight
Selector switch terminalGND
Selector switch terminalDay
GND
Set value potentiometer0-10 V PWM
Set value potentiometer,
supply 10 V (-10 %), 10 mA
+10 V
GND
Control voltage for fan, 0-10 VOUT
Tach output from fanTacho
GND
DC voltage supply (optional),
with reverse battery protection
20 V IN
Line terminals Control terminals
Mains Alarm out
Set valuepotentiometer Selector switch
Fan
DayNight
26
HeidelbergDipl.-Wirt.-Ing. (FH) Jens PeterUhlandstr. 674427 FichtenbergPhone +49 (0) 79 71 / 97 71 50Fax +49 (0) 79 71 / 97 71 [email protected]
KasselDipl.-Ing. (FH) Ralph BrückHoherainstraße 3835075 GladenbachPhone +49 (0) 64 62 / 40 71 10Fax +49 (0) 64 62 / 40 71 [email protected]
KoblenzWinfried SchaeferHinter der Kirch 1056767 UersfeldPhone +49 (0) 26 57 / 16 96Fax +49 (0) 26 57 / 16 [email protected]
MunichRoland KnollLainerbuckel 3884036 LandshutPhone +49 (0) 8 71 / 4 29 70Fax +49 (0) 8 71 / 4 30 41 [email protected]
NurembergFriedrich KleinAdlerstraße 49/173540 HeubachPhone +49 (0) 71 73 / 49 83Fax +49 (0) 71 73 / 80 [email protected]
OffenburgDipl.-Ing (FH) Ralf BraunHubeneck 2177704 OberkirchPhone +49 (0) 78 02 / 98 22 52Fax +49 (0) 78 02 / 98 22 [email protected]
StuttgartDipl.-Ing. (FH) Rudi WeinmannMühlhaldenweg 1373207 PlochingenPhone +49 (0) 71 53 / 92 89 80Fax +49 (0) 71 53 / 92 89 [email protected]
UlmGünter WilhelmAllgäuer Straße 789269 VöhringenPhone +49 (0) 73 06 / 92 46 08Fax +49 (0) 73 06 / 92 46 [email protected]
Distributors
FrankfurtR.E.D. Handelsgesellschaft mbHGutenbergstraße 363110 Rodgau - JügesheimPhone +49 (0) 61 06 / 84 10Fax +49 (0) 61 06 / 84 11 [email protected]
HamburgBreuell + Hilgenfeldt GmbHGrützmühlenweg 4022339 HamburgPhone +49 (0) 40 / 53 80 92 20Fax +49 (0) 40 / 53 80 92 [email protected]
MunichA. Schweiger GmbHOhmstraße 182054 SauerlachPhone +49 (0) 81 04 / 8 97 0Fax +49 (0) 81 04 / 8 97 [email protected]
(1 to 5 pieces)
NorthBreuell + Hilgenfeldt GmbHGrützmühlenweg 4022339 HamburgPhone +49 (0) 40 / 53 80 92 20Fax +49 (0) 40 / 53 80 92 [email protected]
SouthHDS Ventilatoren Vertriebs GmbHGlaswiesenstraße 174677 DörzbachPhone +49 (0) 79 37 / 80 29 68Fax +49 (0) 79 37 / 80 25 [email protected]
Agencies
BerlinDipl.-Ing. (TH) Jens DuchowHändelstraße 716341 PanketalPhone +49 (0) 30 / 94 41 49 62Fax +49 (0) 30 / 94 41 49 [email protected]
BielefeldUlrich BartholomäusVeltmannstraße 949201 DissenPhone +49 (0) 54 21 / 27 46Fax +49 (0) 54 21 / 56 [email protected]
DortmundDipl.-Ing. (FH) Hans-Joachim PundtAuf den Steinern 359519 Möhnesee-VöllinghausenPhone +49 (0) 29 25 / 80 04 07Fax +49 (0) 29 25 / 80 04 [email protected]
FrankfurtDipl.-Ing. Christian KleffmannDr. Hermann-Krause Straße 2363452 HanauPhone +49 (0) 61 81 / 18 98 12Fax +49 (0) 61 81 / 18 98 [email protected]
HalleDipl.-Ing. (TU) Michael HanningLerchenweg 406120 LieskauPhone +49 (0) 3 45 / 5 51 24 56Fax +49 (0) 3 45 / 5 51 24 [email protected]
HamburgIngenieurbüro Breuell GmbHDirk KahlElektroingenieurGrützmühlenweg 4022339 HamburgPhone +49 (0) 40 / 53 80 92 10Fax +49 (0) 40 / 53 80 92 [email protected]
distributors, agencies and subsidiaries
Germany
ebm-papstMulfingen GmbH & Co. KG
Bachmühle 2D-74673 MulfingenPhone +49 (0) 79 38 / 81-0Fax +49 (0) 79 38 / [email protected]
www.ebmpapst.com
ebm-papstSt. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1D-78112 St. GeorgenPhone +49 (0) 77 24 / 81-0Fax +49 (0) 77 24 / 81-13 [email protected]
www.ebmpapst.com
ebm-papstLandshut GmbH
Hofmark-Aich-Straße 25D-84030 LandshutPhone +49 (0) 8 71 / 707-0Fax +49 (0) 8 71 / [email protected]
www.ebmpapst.com
fan agent
compact fan agent
motor specialist
motor agent
27
Europe
Austriaebm-papst Motoren & Ventilatoren GmbHWestbahnstraße 5A-4490 St. FlorianPhone +43 / 72 24 / 66 01 10Fax +43 / 72 24 / 66 01 [email protected]
Belarusebm-papst Bel AgmbHProspekt Nesavisimosti 11/2 Zimmer 325, 512BY-220050 MinskPhone +375 / 17 / 209 95 61Fax +375 / 17 / 209 95 [email protected]
BelgiumVIBO Benelux B. V.Sales office Belgium-LuxemburgRomeinsestraat 6/0101Research Park HaasrodeB-3001 Heverlee-LeuvenPhone +32 / 16 / 39 62 00Fax +32 / 16 / 39 62 [email protected]
Bulgariaebm-papst Romania S.R.L.Str. Tirnavei Nr. 20RO-500327 BrasovPhone +40 / 268 / 312 805Fax +40 / 268 / 312 [email protected]
Croatiaebm-papst Industries Kft.Mátyás u. 1/AH-2220 VecsésPhone +36 / 29 / 55 01 90Fax +36 / 29 / 55 01 [email protected]
CyprusMATERO LTD37, St. Kyriakides AvenueP.O. Box 51744CY-3080 LimassolPhone +357 / 25 / 87 00 30Fax +357 / 25 / 38 13 [email protected]
Czech Republic / Slovakiaebm-papst CZ s.r.o.Krátká 379CZ-66461 Rajhradice u BrnaPhone +420 / 5 / 47 23 26 16Fax +420 / 5 / 47 23 26 [email protected]
DenmarkJenk A/SVallensbækvej 21DK-2605 BrøndbyPhone +45 / 43 / 63 11 11Fax +45 / 43 / 63 05 [email protected]
Finlandebm-papst OyEesti FiliaalPuistotie 1FIN-02760 EspooPhone +358 / 9 / 88 70 22 0Fax +358 / 9 / 88 70 22 [email protected]
Franceebm-papst SARLZI Nord - rue A. MohlerBP 62F-67212 Obernai-CedexPhone +33 / 820 326 266Fax +33 / 3 / 88 67 38 [email protected]
GreeceHelcomaTh. Rotas & Co OEDavaki 65GR-17672 Kallithea-AttikiPhone +30 / 210 / 951 37 05Fax +30 / 210 / 951 34 [email protected]
Hungaryebm-papst Industries Kft.Mátyás u. 1/AH-2220 VecsésPhone +36 / 29 / 55 01 90Fax +36 / 29 / 55 01 [email protected]
IcelandRJ EngineersStangarhyl 1AIS-110 ReykjavikPhone +354 / 567 80 30Fax +354 / 567 80 [email protected]
Irelandebm-papst LimitedPortlaoise Business & Technology ParkMountrath RoadIRL-Portlaoise, Co. LaoisPhone +353 / 57 86 / 643 43Fax +353 / 57 86 / 643 [email protected]
Italyebm-papst SrlVia Cornaggia 108I-22076 Mozzate (Co)Phone +39 / 03 31 / 83 62 01Fax +39 / 03 31 / 82 15 [email protected]
Mazedoniaebm-papst Industries Kft.Mátyás u. 1/AH-2220 VecsésPhone +36 / 29 / 55 01 90Fax +36 / 29 / 55 01 [email protected]
NetherlandsVIBO Benelux B. V.Engelseweg 127Postbus 230NL-5705 AC HelmondPhone +31 / 4 92 / 50 29 00Fax +31 / 4 92 / 50 29 [email protected]
28
ebm-papst RusSaint-Petersburg´s FilialZastavskaya 7RU-196084 Sankt-PetersburgPhone +7 / 812 / 449 96 07Fax +7 / 812 / 449 96 [email protected]
Serbia & Montenegroebm-papst Industries Kft.Mátyás u. 1/AH-2220 VecsésPhone +36 / 29 / 55 01 90Fax +36 / 29 / 55 01 [email protected]
Spainebm-papst Ibérica S.L.Avda. del Sistema Solar, 29C/Monton de Trigo, Nr. 3E-28830 San Fernando de Henares (Madrid)Phone +34 / 91 / 806 44 00Fax +34 / 91 / 804 03 [email protected]
SwedenZiehl-ebm ABÄggelundavägen 2S-17562 JärfällaPhone +46 / 8 / 761 94 00Fax +46 / 8 / 36 23 [email protected]
Switzerlandebm-papst AGRütisbergstraße 1CH-8156 OberhasliPhone +41 / 44 / 732 20 70Fax +41 / 44 / 732 20 [email protected]
TurkeyAkantel Elektronik San. Tic. LTD. Sti.Atatürk Organize SanayiBölgesi 10007 SK. No.:6TR-35620 Cigli-IzmirPhone +90 / 2 32 / 32 82 090 -91Fax +90 / 2 32 / 32 80 [email protected]
Ukraineebm-papst Ukraine GmbHLepse Boulevard 4, Haus 47 Etage 5UA-03680 KievPhone +38 / 044 / 206 30 91Fax +38 / 044 / 206 30 [email protected]
United Kingdomebm-papst UK Ltd.Chelmsford Business ParkGB-Chelmsford Essex CM2 5EZPhone +44 / 12 45 / 46 85 55Fax +44 / 12 45 / 46 63 [email protected]
ebm-papst Automotive & Drives (UK) Ltd.Suite B, The BarnSheepdown, East IlsleyGB-Berkshire RG20 7LYPhone +44 / 87 07 / 66 51 70Fax +44 / 87 07 / 66 51 80A&[email protected]
America
Argentiniaebm-papst de Argentina S.A.Hernandarias 148 Lomas del MiradorPcia. de Buenos Aires (1752)Phone +54 / 11 46 57 61 35Fax +54 / 11 46 57 20 [email protected]
Brasilebm-papst Motores Ventiladores Ltda.Rua Francisco D´Amico, 155Bairro PirajussaraBR-06785-290 Taboão da Serra-SPPhone +55 /11 / 41 38 50 90Fax +55 /11 / 41 38 50 [email protected]
Canadaebm-papst Canada Inc.1800 Ironstone Manor, Unit 2CDN-Pickering, Ontario, L1W3J9Phone +1 / 905 / 420 / 35 33Fax +1 / 905 / 420 / 37 [email protected]
NorwayZiehl-ebm asP.B. 173 HolmliaN-1203 OsloPhone +47 / 22 / 76 33 40Fax +47 / 22 / 61 91 [email protected]
Polandebm-papst Polska Sp. z o.o.ul. Modlinska 4PL-03-216 WarszawaPhone +48 / 22 / 675 78 19Fax +48 / 22 / 676 95 [email protected]
Portugalebm-papst (Portugal), LdaAv. Marechal Gomes da Costa, 35 eRua Conselheiro Emidio NavarroP-1800-255 LisboaPhone +351 / 21 / 839 48 80Fax +351 / 21 / 839 47 [email protected]
Romaniaebm-papst Romania S.R.L.Str. Tirnavei Nr. 20RO-500327 BrasovPhone +40 / 268 / 312 805Fax +40 / 268 / 312 [email protected]
Russiaebm-papst Ural GmbHRosa Luxemburg Strasse 59RU-620026 JekaterinburgPhone +7 / 343 / 378 31 75Fax +7 / 343 / 378 31 [email protected]
ebm-papst Rus GmbHNizhegorodskaya 32, str. 15 office 420RU-109029 MoskauPhone +7 / 495 / 671 53 93Fax +7 / 495 / 671 53 [email protected]
distributors, agencies and subsidiariesfan agent
compact fan agent
motor specialist
motor agent
29
Mexicoebm Industrial S.de R.L. de C.V.Paseo de Tamarindos 400-A-5to PisoCol. Bosques de las LomasMEX-Mexico 05120, D.F.Phone +52 / 55 / 50 91 44 44Fax +52 / 55 / 50 91 44 [email protected]
USAebm-papst Inc.P.O. Box 4009100 Hyde RoadUSA-Farmington, CT 06034Phone +1 / 860 / 674 15 15Fax +1 / 860 / 674 85 [email protected]
Africa
South Africaebm-papst South Africa (Pty) Ltd.P.O. Box 31241119 Yacht AvenueZA-2040 HoneydewPhone +27 / 11 / 794 57 06Fax +27 / 11 / 794 50 [email protected]
Asia
Chinaebm-papst Ventilator (Shanghai) Co., Ltd.No. 418, Huajing RoadWaiGaoQiao Free Trade ZoneNo. 2001, Yang Gao (N) RoadVRC-200131 Shanghai, P.R. of ChinaPhone +86 / 21 / 50 46 01 83Fax +86 / 21 / 50 46 11 [email protected]
Hong Kongebm-papst Ventilator (Shanghai) Co., Ltd.Hong Kong Representative OfficeUnit Nos. 13, 9/F, Technology Park18 On Lai Street, Sha Tin, N.T.HK-Hong Kong P.R. of ChinaPhone +852 / 21 45 / 86 78Fax +852 / 21 45 / 76 [email protected]
Indiaebm NADI International Pvt Ltd.26/3, G.N.T. Road, ErukkencherryIND-Chennai-600118Phone +91 / 44 / 25 37 25 56Fax +91 / 44 / 25 37 11 [email protected]
Indonesiaebm-papst IndonesiaRepresentative OfficeJalan Puri Kencana, Blok K7/3TRI-Jakarta 11610Phone +62 / 21 / 582 / 31 18Fax +62 / 21 / 582 / 31 [email protected]
IsraelPolak Bros. Import Agencies Ltd.P.O. Box 99510, Hayarkon StreetIL-Bnei-Brak 51108Phone +972 / 3 / 617 73 33Fax +972 / 3 / 579 66 [email protected]
Japanebm-papst Industries Japan K.K.12 Floor, Benex S-3 Bldg.3-20-8 Shinyokohama, Kohoku-kuJ-222-0033 YokohamaPhone +81 / 45 / 470 / 57 51Fax +81 / 45 / 470 / 57 [email protected]
Koreaebm-papst Korea Co. Ltd.4F, Doremi Bldg., 260-15Yeomchang-Dong Kangseo-KuROK-Seoul 157-040Phone +82 / 2 / 36 62 / 13 24Fax +82 / 2 / 36 62 / 13 [email protected]
Malaysiaebm-papst MalaysiaRepresentative OfficeBlock F1, 9A-4, Jalan PJU 1/42Dataran PrimaMAL-47301 Petaling JayaPhone +60 / 3 / 78 06 54 40Fax +60 / 3 / 78 06 54 [email protected]
Singaporeebm-papst SEA Pte. Ltd.23 Ubi Road 4, #05-00Olympia Industrial BuildingSGP-Singapore 408620Phone +65 / 68 42 84 38Fax +65 / 68 42 84 [email protected]
TaiwanETECO Engineering & Trading Corp.10F-I, No. 92, Teh-Wei Str.RC-Tsow-Inn District, KaohsiungPhone +886 / 7 / 557 42 68Fax +886 / 7 / 557 27 [email protected]
Thailandebm-papst Thailand Co. Ltd.Representative Office99/349 Chaeng Wattana Road, LaksiBangkok 10210, ThailandPhone +66 / 2 / 576 / 15 24-5Fax +66 / 2 / 576 / 15 [email protected]
United Arab Emiratesebm-papst Middle East FZEPO Box 17755Jebel Ali Free Zone / FZS1 / AP05UAE-DubaiPhone +971 / 4 / 886 08 26Fax +971 / 4 / 886 08 [email protected]
Australia
Australiaebm-papst Australia Pty Ltd.2 Silverton CloseAUS-Laverton North, Victoria, 3026Phone +61 / 3 / 83 25 64 00Fax +61 / 3 / 83 25 64 [email protected]
New Zealandebm-papst Australia Pty Ltd.102 Henderson Valley RoadNZ-Henderson, Auckland 1230Phone +64 / 9 / 837 18 84Fax +64 / 9 / 837 18 [email protected]
Notizen
30
31
37757-7-8811 · GK-07/06-5’
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
D-74673 Mulfingen
Phone +49 (0) 79 38 / 81-0
Fax +49 (0) 79 38 / 81-110
www.ebmpapst.com