Potain MR 615Product Guide
Features
• Luffing jib with maximum radius of 60 m (197 ft)
• 32 t (35.3 USt) maximum capacity
• 8,25 t (9.1 USt) maximum capacity at 60 m (197 ft)
• Internal and external climbing with K mast
• 240 m/min (787 fpm) maximum single-part line speed
Features
K mastPotain’s K mast offers many benefits to your jobsite. Its stepped pins provide easy installation and instant visual inspection decreasing tower assembly time. This mast is available in multiple lengths to allow you to customize the crane to your needs.
Vision cab V140SRVision cab V140SR is equipped with all of the standard features of the V140S with the addition of a guarded glass window on the ceiling for excellent visibility with a luffing jib tower crane.
Multiple jib lengthsThe MR 615 comes standard with a 30 m (98 ft) jib which can be increased in 10 m (33 ft) increments to a maximum jib length of 60 m (197 ft) jib. Able to be luffed from 15˚ – 85˚, the MR 615 can easily maneuver on a restrictive jobsite.
245 LBR 160 hoistThe 245 LBR 160 hoist provides one (1)-part line speeds from 5,7 m/min – 240 m/min (19 fpm – 787 fpm) with loads of 16 t – 2 t (17.6 USt – 2.2 USt) respectively. This 245 hp hoist has a maximum drum capacity of 670 m (2198 ft) and allows for optimized productivity in two (2)-part line configuration as well.
Contents
Specifications 4
Component weights 6
Dimensions 7
Load charts and mast 8
Luffing jib chart and mechanisms 9
Metric dimensions 10
Metric load charts and mast 11
Metric luffing jib chart and mechanisms 12
Symbols glossary 13
4
Specifications
Electrical requirement
480 volt, 60 Hz measured at the turntable.
Dialog Visu and *anemometer
Dialog Visu is standard and displays information to the operator such as height under hook, radius, loads and overload moment, and wind speed (when *anemometer is ordered). Other anemometer options: wind speed alarm, indicator for ground, and recorder.
Swing
RVF 183 Optima + slewing mechanism with maximum swing speed of 1 rpm. Progressive control of speed with counter-slewing possible, anti-load swinging system makes aligning the load and jib easier.
Hoist
245 LBR 160: 245 hp hoist with 670 m (2198 ft) drum capacity is standard with 60 Hz machine. Line speeds range from 2,85 m/min – 120 m/min (9 fpm – 394 fpm) with two (2)-parts of line and 5,7 m/min – 240 m/min (19 fpm – 787 fpm) for one (1)-part of line. Specification of quantity of hoist rope is dependent upon customer’s requirements and mast height.
Luffer
215 VBR: 215 hp variable frequency hoist with a luffing time of one (1) minute thirty (30) seconds from 15˚ to 85˚.
*Optional equipment
• STANDARDNORTHAMERICANSPECIFICATIONMR615:includes60m(197ft)jib, electric slip ring, 60 m of cable 2 x (4G50 mm2), counterweight ballast 65 t (68.3 USt), 320 m (1050 ft) cable D34, anemometer for Dialog Visu, and tropicalization
• Electricslipring• Jibradius40m–60m(131ft–197ft)• TopTracing• Anemometer
*Consult price list for additional options
Jib
30m(98ft)radiuslatticejibstandard.Catwalksareinstalled in all sections for maintenance and easy access to sling points. Identification plates are welded on each section.Thejibfootattachestothepivotpointandlocks in place with two (2) pins. Inspection platform is fixed to the jib nose and equipped with plates on each side for advertising decals.
*Jib extensions
Three(3)optional10m(33ft)jibsectionsareavailablefor radii of 40 m (131 ft), 50 m (164 ft) and 60 m (197 ft).
Counter-jib
One 10,3 m (33.8 ft) design for all jib configurations. It easily attaches to the turntable with a pin. Hoisting and luffing winches are modular to allow for easy erection. Galvanized catwalks allow access to required areas of the counterjib.
*Counter-jib ballast
Ballast blocks are a steel design. Blocks weighing 6000 kg (13,228 lb) are easily erected and secured in quantities according to corresponding jib lengths.
Cab
140 SR Vision cab is standard and includes heating, window vent, tinted glass, windshield wipers, sun visor, document case, electric socket, side pocket, bottle holder, ergonomic seat with high back, adjustable armrests, height and seating with control units, front-to-back shifting and reclining back.
Controls
Dual axis joystick controls integrated into cab seat standard.
Reeving
SM hookblock for 1-part or 2-part line application standard.
*Denotes optional equipment
5Potain MR 615NOTE: The information above is useful as a basic introduction to the crane.
In no case may this serve as a substitute for the serial numbered manuals. Dimensions have been rounded to the nearest tenth.
Specifications
*Mast
K mast in size of K800 2,45 m (8.0 ft), panel or monoblock, and climbing or non-climbing available. Lengths of 3,33 m (10.9 ft), 5 m (16.4 ft), and 10 m (32.8 ft) available. Identification plates welded on each section to designate the type of mast and pin box to stow pins when not in use. Thispatentedpinconnectedmastiswellknownforits robustness, ease of erection and low maintenance connection. Mast nomenclature: K – Series of mast with box angled members M – Monoblock, non climbing R – Reinforced MT–Monoblock&climbing RMT–Reinforced,monoblock,climbingEquippedwithaluminumladdersandgalvanizedsteelrestingplatformsineachsection.Castconnectionsaresecured with two double tapered pins. *Tiraxtooland*Tiraxpinsavailableforfastereasierassembly. Other combinations of masts can allow free-standing HUHtoincrease.Consultusfordetails.
*Climbing equipment
Equipmentavailableforbothinternalclimbingandexternalclimbingof2,45m(8.0ft)mast.Climbingequipment sold separately: hydraulic unit, jack, and collars.Externalclimbingequipmentsoldseparately:climbing cage, hydraulic unit, yoke, and jack.
*Anchor stools
Anchor stools to be used in combination with a concrete foundation or steel structure. Anchors P800A: permanent anchor, maximum free-standing HUH: 57,3 m (188.0 ft) for 2,45 m (8.0 ft) K mast, 60 m (197.0 ft) jib.
*Chassis
Chassisavailablewithsquarefootprintof8m(19.7ft)or10m(32.8ft)forK800mast.Chassisareavailablein either a static mounted configuration or in a traveling configuration with the use of bogies. ChassisY800A:squarefootprintof8m(26.2ft),maximum free-standing HUH: 58,1 m (190.6 ft) for 2,45 m (8.0 ft) K mast, 60 m (197.0 ft) jib. ChassisJ850A:squarefootprintof10m(32.8ft),maximum free-standing HUH: 72,7 m (238.5 ft) for 2,45 m (8.0 ft) K mast, 60 m (197.0 ft) jib.
*Consult price list for additional options
6
Component weights
NOTE: The information above is useful as a basic introduction to the crane. In no case may this serve as a substitute for the serial numbered manuals. Dimensions have been rounded to the nearest tenth.
Item Qty.l
m(ft)
wm
(ft)
hm
(ft)
weightkg(lb)
1 1 Towerhead 2,45 m (8 ft) 2,75 5,13 4,63 13 780 (9.0) (16.8) (15.2) (30,379)
2 1 Cab V140SR and support
3 1 Counter-jib
4 1 Hoisting winch
5 1 Strut + chain block support + pulley block
6 1 Jib foot
7
8 1 Jib section
9 1 Jib section
10 1 Jib section
11 1 Jib section + inspection platform
12 X KR839A2
13 X KR839C2
14 X KMT 850.10C1
15 X KMT850.10A1
16 X KM850-10B1
17 X K850/KR800B1
Component Weights
18 1 Rear half of equipped T850A climbing cage
19 1 Front half of equipped T850A climbing cage
20 4 Fixing angle P800US
1 Jib section
4,62 1,69 2,99 1400 (15.2) (5.5) (9.8) (3086)
6,8 4,5 2,5 18 300 (22.3) (14.8) (8.2) (40,344)
3,75 4,18 2,03 13 550 (12.3) (13.7) (6.7) (29,872)
2,15 2,68 13,9 11 675 (7.1) (8.8) (45.6) (25,739)
9,6 1,9 1,83 3810 (31.5) (6.2) (6) (8399)
10,35 1,9 1,83 1965 (34) (6.2) (6) (4332)
10,35 1,9 1,83 2045 (34) (6.2) (6) (6709)
10,35 1,9 1,83 1755 (34) (6.2) (6) (3869)
10,35 1,9 1,83 1515 (34) (6.2) (6) (3340)
11,35 1,9 2,88 3360 (37.2) (6.2) (9.4) (7407)
5,2 2,5 2,5 4175 (17.2) (8.1) (8.3) (9204)
3,6 2,5 2,5 3065 (11.8) (8.1) (8.3) (6757)
3,7 2,5 2,5 4230 (12) (8.3) (8.2) (9325)
5,3 2,5 2,5 5450 (17.5) (8.3) (8.2) (12,015)
10,3 2,5 2,5 10 070 (33.8) (8.1) (8.3) (22,200)
10,2 2,5 2,5 9730 (33.6) (8.3) (8.3) (21,451)
10,2 4,7 3,3 9230 (33.3) (15.3) (10.8) (20,348)
10,1 4,7 2,6 3690 (33) (15.4) (8.4) (8135)
0,8 0,8 1,8 670 (2.5) (2.5) (5.9) (1477)
7Potain MR 615
Dimensions
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
17.6 USt
113 ft
22 ft
9.1 USt
197 ft
13.8 USt
164 ft
18.2 USt
131 ft
24.8 USt
26.5 USt
35.3 USt
35.3 USt
98 ft
8 ft x 8 ft
5 ft
34 ft
49 ft
26 ft x 26 ft33 ft x 33 ft
8 ft x 8 ft
8
Load charts and mast
NOTE: Illustrated hook heights on this page were determined using FEM 1.001. Configurations shown may include optional equipment. Other codes may require reduction in configurations.
16 ft
121110987654321
98 ft
204188172155139122106907357
P 800 A
H (ft) 16 ft 11 ft
131 ft 194 10 2 164 ft – 197 ft 188 11 -
P 850 A
H
16 ft
1110987654321
98 ft
207196180163147131114988165
Y 800 A
11 ft
26 ft
26 ft
H (ft) 16 ft 11 ft
131 ft 191 9 1 164 ft 185 8 2 197 ft 191 9 1
J 850 A
35 ft
33 ft
K800 Mast
16131 ft 73 8235.3
8931
9828.4
10525.4
11523.6
12121.3
13120 18.2
ft
USt
17.6 USt
19164 ft 93 9826.5
10524.7
11522.9
12120.6
13119.4
13817.6
148 154 16416.6 15.3 14.6 13.5
ft
USt
17.6 15.516.9 14.8 13.2 USt
22197 ft 113 11517.6
12117.3
13116.3
13814.9
14814.0
15412.9
16412.2
17111.4
180 187 19710.9 10.1 19.4 9.1
ft
USt
1198 ft 72 8235.3
8930.4
7234.9
9827.9 24.8
ft
USt
17.6 USt
9Potain MR 615
Luffing jib chart and mechanisms
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
hp kW
1 min 48 s 180 132180 VBR
3 x 12 3 x 9RVF183
Optima +
RT 584A1 - 2V
0 1
8 x 7 8 x 5.244.3 - 88.6
rpm
200 LBR 160 : 375 kVA
CEI 38 IEC 38 kVA
400 V (+6% -10%) 50 Hz
fpm
fpm
USt200 LBR 160 200 150 2198 ft
15/154
17.6
25/253
9.9
39/394
5.5
66/656
2.2
7.7/77
35.3
12.6/126
19.8
20/197
11
33/328
4.4
MR 615 H32 50 Hz
Y 800 A
fpmJ 850 A
hp kW
1 min 30 s 215 158215 VBR
3 x 12 3 x 9RVF183
Optima +
RT 584A1 - 2V
0 1
8 x 8.4 8 x 6.252 - 105
rpm
245 LBR 160 : 445 kVA
CEI 38 IEC 38 kVA
480 V (+6% -10%) 60 Hz
fpm
fpm
USt245 LBR 160 245 180 2198 ft
19/187
17.6
30/302
9.9
47/472
5.5
79/787
2.2
9.4/94
35.3
15/151
19.8
24/236
11
39/394
4.4
MR 615 H32 60 Hz
Y 800 A
fpmJ 850 A
0 33 ft 66 ft 98 ft 131 ft 164 ft 197 ft-33 ft
180 ft
197 ft
131 ft
98 ft
66 ft
33 ft
0
( )
15°
65°
85°
22 ft
19 ft
16 ft
13 ft
12 ft
6.6
ft H
98
24.8 USt
22 ft 30
ft 38 ft
131
18.2 USt
164
13.8 USt
197
9.1 USt
74 ft
89 ft
80 ft
55°
( )
95 ft
( )
25°
10
Metric dimensions
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
16 t
34,9 m
5,6 m
8,25 t
60 m
12,25 t
50 m
16,5 t
40 m
22,5 t
24 t
32 t
32 t
30 m
2,45 m x 2,45 m
1,6 m
10,3 m
15 m
8 m x 8 m10 m x 10 m
2,45 m x 2,45 m
11Potain MR 615NOTE: Illustrated hook heights on this page were determined using FEM 1.001.
Configurations shown may include optional equipment. Other codes may require reduction in configurations.
Metric load charts and mast
4,240 m 22,4 2532
2728,3
3026
3223,1
3521,4
3719,3
4018,1 16,5
m
t
16 t
4,950 m 28,4 3024
3222,5
3520,9
3718,9
4017,7
4216,1
45 47 5015,2 14 13,2 12,25
m
t
16 14,2515,5 13,45 12 t
5,660 m 34,9 3516
3715,9
4014,9
4213,6
4512,9
4711,8
5011,2
5210,4
55 57 609,9 9,2 8,8 8,25
m
t
3,4 30 m 21,9 2532
2727,6
2231,8
3025,4 22,5
m
t
16 t
5 m
121110987654321
30 m
62,357,352,347,342,337,332,327,322,317,3
P 800 A
H (m) 5 m 3.33 m
40 m 59 10 2 50 m - 60 m 57,3 11 —
P 850 A
H
5 m
1110987654321
30 m
63,159,854,849,844,839,834,829,824,819,8
Y 800 A
3,33
m
7,8 m
8 m
H (m) 5 m 3.33 m
40 m 58,1 9 1 50 m 56,4 8 2 60 m 58,1 9 1
J 850 A
10,8
m
10 m
K800 Mast
12THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Metric luffing jib chart and mechanisms
hp kW
1 min 30 s 215 158215 VBR
3 x 12 3 x 9RVF183
Optima +
RT 584A1 - 2V
8 x 8,4 8 x 6,216 - 32
rpm
245 LBR 160 : 445 kVA
CEI 38 IEC 38 kVA
480 V (+6% -10%) 60 Hz
m/min
m/min
t245 LBR 160 245 180 670 m
5,7/57
16
9,2/92
9
14,4/144
5
24/240
2
2,85/28,5
32
4,6/46
18
7,2/72
10
12/120
4
MR 615 B H32 60 Hz
Y 800 A
m/minJ 850 A
0 � 1
0 10 m 20 m 30 m 40 m 50 m 60 m-10 m
50 m
60 m
40 m
30 m
20 m
10 m
0
( )
( )
( )
15°
25°55°
65°
85°
6,7 m
5,8 m
4,9 m
4 m
3,7
m
2 m H
30
22,5 t
6,4
m
9,1 m 11,7
m
40
16,5 t
50
12,5 t
60
8,25 t
24,4
22,7
27,1
28,95
13Potain MR 615
Symbols glossary
14
Notes
15Potain MR 615
Notes
Thisdocumentisnon-contractual.Constantimprovementandengineeringprogressmake it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.
AmericasBrazilAlphavilleMexicoMonterreyChileSantiago
Europe, Middle East & AfricaAlgeriaHydraCzech RepublicNetvoriceFranceBaudemontCergyDecinesGermanyLangenfeldHungaryBudapestItalyParabiagoNetherlandsBredaPolandWarsaw
PortugalBaltarLisbonRussiaMoscowU.A.E.DubaiU.K.Buckingham
Asia - PacificAustraliaBrisbaneMelbourneSydneyChinaBeijingSingaporeXi’anKoreaSeoulIndiaHyderabadPunePhilippinesMakati City
FactoriesBrazilAlphavilleChinaTaiAnZhangjiagangFranceCharlieuLa ClayetteMoulinsGermanyWilhelmshavenIndiaPuneItalyNiella TanaroPortugalBaltarFânzeresSlovakiaSarisUSAManitowoc Port WashingtonShady Grove
Regional offices
Manitowoc - Asia Pacific Shanghai, China Tel: +86 21 6457 0066Fax: +86 21 6457 4955
Manitowoc - Europe, Middle East & Africa Ecully, France Tel: +33 (0)4 72 18 20 20 Fax: +33 (0)4 72 18 20 00
Manitowoc - AmericasManitowoc, Wisconsin, USA Tel: +1 920 684 6621 Fax: +1 920 683 6278
Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 4062
©2009 ManitowocPrinted in USAForm No. MR615Part No. 08-016 / 0209 / 1M www.manitowoc.com
Regional headquarters
