PREDCR/ AUTODCR FAQ’s - 2.0v
PREDCR/AUTODCR FAQ’s 2.0v Page 2
Table of Contents
Q1. What system settings are required for installation of PREDCR / AUTODCR? ....................... 3
Q2. How to ‘mark margin’ in PREDCR drawing? ......................................................................... 16
Q3. How to mark green strip in PREDCR drawing? ..................................................................... 19
Q4. How to mark road widening in PREDCR drawing? ............................................................... 22
Q5. How to write main road text in PREDCR drawing ? ............................................................. 25
Q6. How to draw section line in site plan in PREDCR drawing? ................................................. 26
Q8. How to mark nala/canal/water bodies in PREDCR drawing ? ............................................ 33
Q9. How to select road widening concession in PREDCR drawing? ........................................... 37
Case No .1: To select road widening concession as “Grant of TDR” ....................................................... 37
Case No .2: To select road widening concession as “RW Setback Concession” ..................................... 39
Case No. 3: To select road widening concession as ‘Additional Floors’ ................................................. 40
Case No .4:-To Select road widening concession as “All (includes Grant of TDR, RW Setback Concession
and Additional Floor)” ............................................................................................................................. 41
Q10. How to mark special_use_bua in PREDCR drawing ?......................................................... 43
Case No.1: To mark BUA for special use building e.g. proposed church building .................................. 43
Q11. How to mark mortgage area for total bua in PREDCR drawing? ...................................... 48
General instructions: .................................................................................................................... 49
PREDCR/AUTODCR FAQ’s 2.0v Page 3
Q1. What system settings are required for installation of PREDCR / AUTODCR?
Point A) Give full rights to C drive.
Step 1: Go to control panel.
Step 2: Click on user accounts.
PREDCR/AUTODCR FAQ’s 2.0v Page 4
Step 3: Click on ‘Change user account control settings’.
Step 4:- Now move the cursor to never notify.
PREDCR/AUTODCR FAQ’s 2.0v Page 5
Step 5: Restart the machine.
Step 6: Open start menu, then type “Regedit” and hit enter as shown in below screenshot.
Step 7: Follow the path:
HKEY_LOCAL_MACHINESOFTWAREMICROSOFTWINDOWSCURRENT
VERSIONPOLICYSYSTEM.
PREDCR/AUTODCR FAQ’s 2.0v Page 6
PREDCR/AUTODCR FAQ’s 2.0v Page 7
PREDCR/AUTODCR FAQ’s 2.0v Page 8
Step 8: Change the EnableLUA value to 0.
PREDCR/AUTODCR FAQ’s 2.0v Page 9
Step 9: Restart the machine.
Point B) To check the error in application
Step 1: Go to control panel.
Step 2: Click on system security.
PREDCR/AUTODCR FAQ’s 2.0v Page 10
Step 3: Click on Administrative tools.
Step 4: Click on Event viewer.
PREDCR/AUTODCR FAQ’s 2.0v Page 11
Step 5: Click on Window log.
Step 6: Click on application to check the application related errors and click on system to check
the system related errors.
PREDCR/AUTODCR FAQ’s 2.0v Page 12
Point C) To check the HASP drivers for autodcr and predcr
Step 1:- Open start menu, then type “Run”.
Step 2: Open start menu, then type “Regedit” and hit enter as shown in below screenshot.
PREDCR/AUTODCR FAQ’s 2.0v Page 13
Step 3: Follow the path
HKEY_LOCAL MACHINESOFTWAREWOW6432 NODECOSERVER
PREDCR/AUTODCR FAQ’s 2.0v Page 14
Step 4: In Coserver, check CoActivator and CoPDCRActivator folder
PREDCR/AUTODCR FAQ’s 2.0v Page 15
Step 5: Also check corresponding AutoDCR and PreDCR folder in SEPL.
PREDCR/AUTODCR FAQ’s 2.0v Page 16
Q2. How to ‘mark margin’ in PREDCR drawing?
Step 1: Click on second tab ‘mark margin’ command of PreDCR Toolbar.
Step 2 : Select ‘Yes’ button.
PREDCR/AUTODCR FAQ’s 2.0v Page 17
Step 3: ‘Click corresponding button to mark the margins’ select rear, side 1 and side 2 margins
in drawing.
Step 4: Click ‘Ok’.
PREDCR/AUTODCR FAQ’s 2.0v Page 18
Notes:
1) Plot poly line, Net plot poly line and Margin lines are not drawn twice.
2) All poly line entities should be closed.
3) Check the road layer and text.
4) Site Plan contains plot ploy line, net area ploy line, margin line , proposed work(building
line) ,road (existing /road widening ), green strip, RWHS, Amenities/sub structure.
PREDCR/AUTODCR FAQ’s 2.0v Page 19
Q.3. How to mark green strip in PREDCR drawing?
Step 1: Select ‘OrganizedOpenSpace’ layer in l ayer dropdown.
Step 2: Draw Green strip closed poly line in the drawing.
PREDCR/AUTODCR FAQ’s 2.0v Page 20
Step 3: To mark Green Strip follow the path.
Mark Organized Open Space Green Strip
PREDCR/AUTODCR FAQ’s 2.0v Page 21
Step 4: Select ‘OrganizedOpenSpace’ polylines and press “ENTER”.
PREDCR/AUTODCR FAQ’s 2.0v Page 22
Q.4. How to mark road widening in PREDCR drawing?
Step 1: Select ‘RoadWidening’ layer in Layer Dropdown.
Step 2: Draw ‘Road Widening’ using closed poly line.
PREDCR/AUTODCR FAQ’s 2.0v Page 23
Step 3: To mark “Road Widening” follow the path.
Mark Road WideningsUndo marking (Default)/Surrendered Free of Cost.
PREDCR/AUTODCR FAQ’s 2.0v Page 24
Step 4: Select ‘RoadWidening’ polylines and press “ENTER”.
PREDCR/AUTODCR FAQ’s 2.0v Page 25
Q.5. How to write main road text in PREDCR drawing ?
Above screen shot is an example capturing incorrect road text in drawing.
Step 1: Select ‘Main road’ layer, go to Mtext and write as shown below.
Above screen shot is an example capturing correct road text in drawing.
PREDCR/AUTODCR FAQ’s 2.0v Page 26
Q.6. How to draw section line in site plan in PREDCR drawing?
Step 1: Select “SectionLine” layer in Layer Dropdown.
Step 2: Draw 'Section Line’ using “PL (PLINE)” command.
PREDCR/AUTODCR FAQ’s 2.0v Page 27
Step 3:-Text “Section Line” using “MT (MTEXT) command.
PREDCR/AUTODCR FAQ’s 2.0v Page 28
PREDCR/AUTODCR FAQ’s 2.0v Page 29
Q7. How to mark drawing reference points in PREDCR drawing?
Step 1: Direction Ref Circle: Use this command to insert Direction Ref Point (Orientation) inside Floor and PropWork.
PREDCR/AUTODCR FAQ’s 2.0v Page 30
Step2: From PreDCR dropdown toolbar, select the following:
PreDCR Insert Direction Ref Circles
PREDCR/AUTODCR FAQ’s 2.0v Page 31
Step3: Insert the Direction Ref Circles inside the PropWork in the plot.
PREDCR/AUTODCR FAQ’s 2.0v Page 32
Step 4: Copy the Direction Ref Circles by selecting a common point from inserted site plan
and place it in the required floor plans.
Step 5 : After Copying the Direction ref Circles in all plans (including Terrace floor plan) then
PreDCR verification can be done.
PREDCR/AUTODCR FAQ’s 2.0v Page 33
Q8. How to mark nala/canal/water bodies in PREDCR drawing ?
Step 1: Select “_WaterBodies” Layer in Layer dropdown.
PREDCR/AUTODCR FAQ’s 2.0v Page 34
Step 2: Draw Water body using “Pline” command. Polyline for water body should be open .
PREDCR/AUTODCR FAQ’s 2.0v Page 35
Step 3: Mark the corresponding water body as shown in below path.
MarkWaterBodiesRiver/FTL boundary of Lakes/Tanks/Kuntas of area 10Ha and above/ FTL boundary of Lakes/Tanks/Kuntas of area less than 10Ha/ Shikam lands / Defined boundary of Canal, Vagu, Nala, Storm Water Drain of width more than 10m /Defined boundary of Canal, Vagu, Nala, Storm Water Drain of width up to 10m.
PREDCR/AUTODCR FAQ’s 2.0v Page 36
Step 4: Select “Water Body” and Press “ENTER” button.
PREDCR/AUTODCR FAQ’s 2.0v Page 37
Q9. How to select road widening concession in PREDCR drawing?
Case No 01: To select road widening concession as “Grant of TDR”
Step 1: Click on “Road Widening Concession” dropdown in DCR Project dialog box .
Step2: Select “Grant of TDR” option.
PREDCR/AUTODCR FAQ’s 2.0v Page 38
Step3: Enter “TDR Area” and click on ‘OK’ button.
PREDCR/AUTODCR FAQ’s 2.0v Page 39
Case No 02: To select road widening concession as “RW Setback Concession”
Step 1: Click on ‘Road Widening Concession’ dropdown in DCR Project dialog box .
Step 2: Select ‘RW setback concession’ and Click on ‘OK’ button.
PREDCR/AUTODCR FAQ’s 2.0v Page 40
Case no 03: To select road widening concession as ‘Additional Floors’
Step 1: Click on ‘Road Widening Concession’ dropdown in DCR Project dialog box .
Step 2: Select ‘Additional Floors’ option, Enter ‘Road widening Floor No’ and click on ‘OK’
button.
PREDCR/AUTODCR FAQ’s 2.0v Page 41
Case No 04:-To Select road widening concession as “All (includes Grant of TDR, RW Setback
Concession and Additional Floor)”
Step 1: Click on “Road Widening Concession” dropdown in DCR Project dialog box .
PREDCR/AUTODCR FAQ’s 2.0v Page 42
Step 2:-Select ‘ALL’ option, Enter ‘Road widening Floor No & TDR Area’ and click on ‘OK’button.
PREDCR/AUTODCR FAQ’s 2.0v Page 43
Q10. How to mark special_use_bua in PREDCR drawing ?
Case No 01: To mark BUA for special use building e.g. proposed church building
Step 1:- Select Plot Use – Assembly.
PREDCR/AUTODCR FAQ’s 2.0v Page 44
Step 2:- Select, Plot Sub Use – Religious (since propsed building is a church).
Step 3:- Select Land Use Zone according to the land details. (in this case it is NA), Then click OK.
PREDCR/AUTODCR FAQ’s 2.0v Page 45
Step 4:- The specific layer for Assemblyreligiousbuilding will therefore be created in
PreDCR. (As shown below)
PREDCR/AUTODCR FAQ’s 2.0v Page 46
Step 5:-Draw BUA polyline for structure under layer SpecialUse_BUA in the proposed building
Plan.
Step 6:-Then Mark Special use BUA polyline, under PreDCR drop down toolbar,
MarkSpecialUse FAR Markings Assembly.
PREDCR/AUTODCR FAQ’s 2.0v Page 47
Step 7:-Select “_SpecialUseBUAOutline Polylines” & press “Enter”.
Step 8: After Following these steps in marking BUA for special use Buildings, Then proceed with
the PreDCR Verification.
PREDCR/AUTODCR FAQ’s 2.0v Page 48
Q11. How to mark mortgage area for total bua in PREDCR drawing?
According to (G.O Ms – 168; 25, d) The owner is required to hand over 10% of the built-up area in the ground floor or first
floor or the second floor, as the case may be. In respect of row houses / detached houses / cluster housing 5% of the units shall be
handed over. Then only the Building sanction will be released.
Step 1:-Draw Mortgage area polyline according to the required area on one of the proposed
floors. (Ground / First / Second) according to the case.
PREDCR/AUTODCR FAQ’s 2.0v Page 49
Step 2: Mark the Mortgage area polyline from PreDCR dropdown toolbar;
MarkMortgage area Built Up Area to Mortgage.
Step 3: After Marking the Mortgage area Polyline, PreDCR verification can be done.
General instructions:
1) Always run PreDCR before AutoDCR scrutiny.
2) Cross check AUTODCR scrutiny results with drawing.
3) Check other parameters like land use, Sub landuse while running the drawing.
★★★