8/6/2019 Preprint 48 Meses Log Book 1

1/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTEFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

XRmvd Cotter Pin securing self-retaining bolt on collective inputcontrol Rod To collective Torque Shaft lever

XRmvd self-retaining bolt and hdwr securing collective inputcontrol Rod To collective Torque Shaft lever

XRmvd cotter pin securing bolt (1 17/32) on collective input

control Rod To collective Torque Shaft lever

XRmvd bolt (1 17/32),short bushings, washers and nut securingcoll input control Rod To coll Torque Shaft lever

XRmvd cotter pin securing bolt (1 13/32) on collective inputcontrol Rod To collective Torque Shaft lever

XRmvd bolt (1 13/32),long bushing, washers and nut securing

coll input control Rod To coll Torque Shaft lever

XDisconnected collective input control Rod From collectiveTorque Shaft lever

XRmvd Cotter Pin securing self-retaining bolt on collective inputcontrol Rod To collective servo arm

XRmvd self-retaining bolt and hdwr securing collective inputcontrol Rod To collective servo arm

XRmvd cotter pin securing bolt (1 17/32) on collective input

control Rod To collective servo arm

XRmvd bolt (1 17/32),short bushings, washers and nut securingcoll input control Rod To collective servo arm

XRmvd cotter pin securing bolt (1 13/32) on collective inputcontrol Rod To collective servo arm

XRmvd bolt (1 13/32),long bushing, washers and nut securing

coll input control Rod To collective servo arm

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

2/17

8.STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTTLEVEL 13. MMH

X Removed collective input control Rod From collective servo arm

XRmvd safty wire securing rod end and jamnuts on coll inputcontrol rod

X Loosened rod end jamnut securing rod end

X Removed rod end from sleeve

XRemoved locking devices from rod end

X Removed jamnut from adjustable rod end

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

XDissembled collective tube assembly

XRmvd Cotter Pin securing self-retaining bolt on pitch inputcontrol Rod To pitch Torque Shaft lever

XRmvd self-retaining bolt and hdwr securing pitch input control

Rod To pitch Torque Shaft lever

XRmvd cotter pin securing bolt (1 17/32) on pitch input control

Rod To pitch Torque Shaft lever

XRmvd bolt (1 17/32),short bushings, washers and nut securingpitch input control Rod To pitch Torque Shaft lever

X

Rmvd cotter pin securing bolt (1 13/32) on pitch input control

Rod To pitch Torque Shaft lever

XRmvd bolt (1 13/32),long bushing, washers and nut securing

pitch input control Rod To pitch Torque Shaft lever

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

3/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

XDisconnected pitch input control Rod From pitch Torque Shaftlever

XRmvd Cotter Pin securing self-retaining bolt on pitch inputcontrol Rod To pitch/trim servo lever

XRmvd self-retaining bolt and hdwr securing pitch input controlRod To pitch/trim servo lever

XRmvd cotter pin securing bolt (1 17/32) on pitch input control

Rod To pitch Torque Shaft lever

XRmvd bolt (1 17/32),short bushings, washers and nut securingpitch input control Rod To pitch/trim servo lever

XRmvd cotter pin securing bolt (1 13/32) on pitch input controlRod To pitch/trim servo lever

XRmvd bolt (1 13/32),long bushing, washers and nut securing

pitch input control Rod To pitch/trim servo lever

X Removed pitch input control Rod From pitch/trim servo lever

XRmvd safty wire securing rod end and jamnuts on pitch inputcontrol rod

X Loosened rod end jamnut securing rod end

XRemoved rod end from sleeve

X Removed locking devices from rod end

X Removed jamnut from adjustable rod endDA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

4/17

8.STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTTLEVEL 13. MMH

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

X Dissembled pitch tube assembly

X

Rmvd Cotter Pin securing self-retaining bolt on roll input control

Rod To roll Torque Shaft lever

XRmvd self-retaining bolt and hdwr securing roll input control

Rod To roll Torque Shaft lever

XRmvd cotter pin securing bolt (1 13/32) on roll input control Rod

To roll Torque Shaft lever

XRmvd bolt (1 13/32),short bushings, washers and nut securingroll input control Rod To roll Torque Shaft lever

XRmvd cotter pin securing bolt (1 5/32) on roll input control Rod

To roll Torque Shaft lever

X

Rmvd bolt (1 5/32),long bushing, washers and nut securing roll

input control Rod To roll Torque Shaft lever

XDisconnected roll input control Rod From roll Torque Shaftlever

XRmvd Cotter Pin securing self-retaining bolt on roll input controlRod To roll actuator lever

XRmvd self-retaining bolt and hdwr securing roll input control

Rod To roll actuator lever

XRmvd cotter pin securing bolt (1 13/32) on roll input control Rod

To roll actuator lever

X

Rmvd bolt (1 13/32),short bushings, washers and nut securing

roll input control Rod To roll actuator lever

XRmvd cotter pin securing bolt (1 5/32) on roll input control Rod

To roll actuator lever

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

5/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

XRmvd bolt (1 5/32),long bushing, washers and nut securing rollinput control Rod To roll actuator lever

X Removed roll input control Rod From roll actuator lever

XRmvd safty wire securing rod end and jamnuts on roll input

control rod

X Loosened rod end jamnut securing rod end

X Removed rod end from sleeve

X Removed locking devices from rod end

X Removed jamnut from adjustable rod end

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

X Dissembled roll tube assembly

XRmvd Cotter Pin securing self-retaining bolt on yaw inputcontrol Rod To yaw Torque Shaft lever

XRmvd self-retaining bolt and hdwr securing yaw input control

Rod To yaw Torque Shaft lever

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

6/17

8.STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTTLEVEL 13. MMH

XRmvd cotter pin securing bolt (1 13/32) on yaw input control

Rod To yaw Torque Shaft lever

XRmvd bolt (1 13/32),short bushings, washers and nut securingyaw input control Rod To yaw Torque Shaft lever

XRmvd cotter pin securing bolt (1 13/32) on yaw input control

Rod To yaw Torque Shaft lever

XRmvd bolt (1 13/32),long bushing, washers and nut securingyaw input control Rod To yaw Torque Shaft lever

X

Disconnected yaw input control Rod From yaw Torque Shaft

lever

XRmvd Cotter Pin securing self-retaining bolt on yaw input

control Rod To yaw servo lever

XRmvd self-retaining bolt and hdwr securing yaw input control

Rod To yaw servo lever

XRmvd cotter pin securing bolt (1 13/32) on yaw input control

Rod To yaw servo lever

XRmvd bolt (1 13/32),short bushings, washers and nut securingyaw input control Rod To yaw servo lever

X

Rmvd cotter pin securing bolt (1 13/32) on yaw input control

Rod To yaw servo lever

XRmvd bolt (1 13/32),long bushing, washers and nut securingyaw input control Rod To yaw servo lever

X Removed yaw input control Rod From yaw servo lever

XRmvd safty wire securing rod end and jamnuts on yaw input

control rod

X Loosened rod end jamnut securing rod end

XRemoved rod end from sleeve

X Removed locking devices from rod end

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

7/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

X Removed jamnut from adjustable rod end

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

X Dissembled yaw tube assembly

XRmvd Cotter Pin securing self-retaining bolt on collective

control Rod to collective boost servo output arm

XRmvd self-retaining bolt and hdwr securing collective controlRod to collective boost servo output arm

XRmvd cotter pin securing bolt (1 17/32) on collective controlRod to collective boost servo output arm

XRmvd bolt (1 17/32),long bushing, washers and nut securingcollective control Rod to collective boost servo output arm

XRmvd cotter pin securing bolt (1 25/32) on collective control

Rod to collective boost servo output arm

XRmvd bolt (1 25/32),short bushing, washers and nut securingcollective control Rod to collective boost servo output arm

XDisconnected collective control Rod from collective boost servooutput arm

XRmvd cotter pin securing self-retaining bolt on collective control

rod to mixer arm

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

8/17

8.

STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTT

LEVEL 13. MMH

XRmvd self-retaining bolt and hdwr securing collective control rodto mixer arm

XRmvd cotter pin securing bolt on collective control rod to mixerarm

XRemove bolt, washer, flanged bushing, and nut securing

collective control rod to mixer arm

X Removed collective control rod from mixer arm clevis

X

Rmvd safty wire securing rod end and jamnuts on collective

control rod

X Loosened rod end jamnut securing rod end

X Removed rod end from adjuster

X Removed locking devices from adjuster

X Removed jamnut from adjuster

XLoosened adjuster jamnut securing tube assembly

X Removed adjuster from tube assembly

X Removed jamnut from adjuster

X Dissembled collective control Rod tube assembly

XRmvd cotter pin securing self-retaining bolt on lateral control rodto mixer lever

XRmvd self-retaining bolt and hdwr securing lateral control rod to

mixer lever

XRmvd cotter pin securing bolt on lateral control rod to mixerlever

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

9/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

X Rmvd bolt and hdwr securing lateral control rod to mixer lever

X Disconnected lateral control rod from mixer lever

XRmvd cotter pin securing self-retaining bolt on lateral control rod

to roll actuator lever

XRmvd self-retaining bolt and hdwr securing lateral control rod toroll actuator lever

XRmvd cotter pin securing bolt (1 9/32) on lateral control rod toroll actuator lever

XRmvd bolt (1 9/32) long bushing, washers and nut securing

lateral control rod to roll actuator lever

XRmvd cotter pin securing bolt (1 17/32) on lateral control rod toroll actuator lever

XRmvd bolt (1 17/32) short bushings, washers and nut securinglateral control rod to roll actuator lever

X Removed lateral control rod to roll actuator lever

XRmvd safty wire securing rod end and jamnuts on lateral

control rod

X Loosened rod end jamnut securing rod end

X Removed rod end from sleeve

X Removed locking devices from rod endDA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

10/17

8.

STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTT

LEVEL 13. MMH

X Removed jamnut from adjustable rod end

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

XDissembled lateral control rod tube assembly

XRmvd Cotter Pin securing self-retaining bolt on Yaw Boost

Servo Control Rod to yaw boost servo output arm

XRmvd self-retaining bolt and hdwr securing Yaw Boost ServoControl Rod to yaw boost servo output arm

XRmvd cotter pin securing bolt (1 17/32) on Yaw Boost ServoControl Rod to yaw boost servo output arm

XRmvd bolt (1 17/32),long bushing, washers and nut securing

Yaw Boost Servo Control Rod to yaw boost servo output arm

X

Rmvd cotter pin securing bolt (1 21/32) on Yaw Boost Servo

Control Rod to yaw boost servo output arm

XRmvd bolt (1 21/32),short bushing, washers and nut securingYaw Boost Servo Control Rod to yaw boost servo output arm

XDisconnected Yaw Boost Servo Control Rod from yaw boost

servo output arm

XRmvd cotter pin securing self-retaining bolt on Yaw BoostServo Control Rod to mixer lever

XRmvd self-retaining bolt and hdwr securing Yaw Boost ServoControl Rod to mixer lever

XRmvd cotter pins (02 EA) securing bolts on Yaw Boost Servo

Control Rod to mixer lever

XRemove bolts, (02 EA) washers, long bushings, and nutssecuring Yaw Boost Servo Control Rod to mixer lever

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

11/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

X Removed Yaw Boost Servo Control Rod from mixer lever

XRmvd safty wire securing rod end and jamnuts on Yaw BoostServo Control Rod

X Loosened rod end jamnut securing rod end

X Removed rod end from sleeve

X Removed locking devices from rod end

X Removed jamnut from adjustable rod end

X Loosened sleeve jamnut securing tube assembly

X Removed sleeve from tube assembly

X Removed jamnut from sleeve

X Dissembled yaw control rod tube assembly

XRmvd Cotter Pins (02 EA) From Bolts On FWD Input ControlRod To Primary Servo bearing retention plate

XRmvd bolts (02 EA) and hdwr from Fwd Input Control Rod To

FWD primary servo bearing retention plate

XDisconnected FWD Input Control Rod From primary servo

bearing retention plate

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

12/17

8.

STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTT

LEVEL 13. MMH

XRmvd cotter pin securing self-retaining bolt on FWD InputControl Rod to mixer FWD output lever

XRmvd self-retaining bolt and hdwr securing FWD Input ControlRod to mixer FWD output lever

XRmvd cotter pin securing bolt on FWD Input Control Rod Fwd

Input Control Rod to mixer FWD output lever

XRmvd bolt, bushing and hdwr securing FWD Input Control Rodto mixer FWD output lever

XRemoved FWD Input Control Rod from mixer FWD output lever

XRemoved safty wire securing rod end clevis and jamnuts on

FWD Input Control Rod

X Loosened rod end clevis jamnut securing rod end

X Removed rod end clevis from sleeve

X Removed locking devices from rod end clevis

XRemoved jamnut from rod end clevis

X Loosened barrel jamnut securing tube assembly

X Removed barrel from tube assembly

X Removed jamnut from tube assembly

X Dissembled FWD control rod tube assembly

XRmvd Cotter Pins (02 EA) from bolts on AFT Input Control Rod

To Primary Servo bearing retention plate

XRmvd bolts (02 EA) and hdwr from AFT Input Control Rod To

AFT primary servo bearing retention plate

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

13/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

XDisconnected AFT Input Control Rod From primary servo

bearing retention plate

XRmvd cotter pin securing self-retaining flush head bolt on AFTInput Control Rod to mixer AFT output lever

XRmvd self-retaining flush head bolt and hdwr securing AFT

Input Control Rod to mixer AFT output lever

XRmvd cotter pin securing (1 9/16) flush head bolt on AFT InputControl Rod to mixer AFT output lever

XRmvd (1 9/16) flush head bolt, countersunk bushing and hdwrsecuring AFT Input Control Rod to mixer AFT output lever

XRmvd cotter pin securing (1 17/32) flush head bolt on AFT

Input Control Rod to mixer AFT output lever

XRmvd (1 17/32) flush head bolt, countersunk bushing and hdwrsecuring AFT Input Control Rod to mixer AFT output lever

X Removed AFT Input Control Rod from mixer AFT output lever

XRemoved safty wire securing rod end clevis and jamnuts onAFT Input Control Rod

X Loosened rod end clevis jamnut securing rod end

X Removed rod end clevis from sleeve

X Removed locking devices from rod end clevis

X Removed jamnut from rod end clevisDA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

14/17

8.

STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTT

LEVEL 13. MMH

X Loosened barrel jamnut securing tube assembly

X Removed barrel from tube assembly

X Removed jamnut from tube assembly

X Dissembled AFT control rod tube assembly

X

Rmvd Cotter Pins (02 EA) from Bolts On LAT Input Control Rod

To Primary Servo bearing retention plate

XRmvd bolts (02 EA) and hdwr From LAT Input Control Rod To

LAT primary servo bearing retention plate

XDisconnected LAT Input Control Rod From primary servo

bearing retention plate

XRmvd cotter pin securing self-retaining bolt on LAT InputControl Rod to mixer LAT output lever

XRmvd self-retaining bolt and hdwr securing LAT Input ControlRod to mixer LAT output lever

X

Rmvd cotter pins (02 EA) securing bolts on LAT Input Control

Rod to mixer LAT output lever

XRmvd bolts, (02 EA),bushings and hdwr securing LAT InputControl Rod to mixer LAT output lever

X Removed LAT Input Control Rod from mixer LAT output lever

XRemoved safty wire securing rod end clevis and jamnuts on

LAT Input Control Rod

X Loosened rod end clevis jamnut securing rod end

X Removed rod end clevis from sleeve

X Removed locking devices from rod end clevis

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

15/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

X Removed jamnut from rod end clevis

X Loosened barrel jamnut securing tube assembly

X Removed barrel from tube assembly

X Removed jamnut from tube assembly

X Dissembled LAT control rod tube assembly

XRmvd Cotter Pin securing self-retaining bolt on ForwardQuadrant Control Rod to yaw lever

XRmvd self-retaining bolt and hdwr securing Forward QuadrantControl Rod to yaw lever

XRmvd cotter pin securing bolt on Forward Quadrant Control Rodto yaw lever

XRmvd bolt ,long bushing, washers and nut securing ForwardQuadrant Control Rod to yaw lever

XRmvd cotter pin securing bolt on Forward Quadrant Control Rod

to yaw lever

XRmvd bolt ,short bushing, washers and nut securing ForwardQuadrant Control Rod to yaw lever

X Disconnected Forward Quadrant Control Rod from yaw lever

XRmvd cotter pin securing self-retaining bolt on Forward

Quadrant Control Rod to Forward Quadrant lever

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

16/17

8.

STA 9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID

12.MANTT

LEVEL 13. MMH

XRmvd self-retaining bolt and hdwr securing Forward QuadrantControl Rod to Forward Quadrant lever

XRmvd cotter pin securing bolt (1 1/8) on Forward QuadrantControl Rod to Forward Quadrant lever

XRmvd bolt (1 1/8),long bushing, washers and nut securing

Forward Quadrant Control Rod to Forward Quadrant lever

XRmvd cotter pin securing bolt (1 1/16) on Forward QuadrantControl Rod to Forward Quadrant lever

X

Rmvd bolt (1 1/16),short bushing, washers and nut securing

Forward Quadrant Control Rod to Forward Quadrant lever

XRemoved Forward Quadrant Control Rod from Forward

Quadrant lever

X Loosened rod end jamnut

X Removed rod end from fwd quadrant control rod

X Dissembled fwd quadrant control rod tube assembly

XRmvd Cotter Pin securing self-retaining bolt on Tail Rotor

Quadrant Pushrod To tail rotor servo

XRmvd self-retaining bolt and hdwr securing Tail Rotor QuadrantPushrod To tail rotor servo

XRmvd cotter pin securing bolt (1 3/16) on Tail Rotor Quadrant

Pushrod To tail rotor servo

XRmvd bolt (1 3/16),short bushings, washers and nut securing

Tail Rotor Quadrant Pushrod To tail rotor servo

XRmvd cotter pin securing bolt (1 7/16) on Tail Rotor Quadrant

Pushrod To tail rotor servo

XRmvd bolt (1 7/16),long bushing, washers and nut securing Tail

Rotor Quadrant Pushrod To tail rotor servo

X Disconnected Tail Rotor Quadrant Pushrod from tail rotor servo

CONTINUE

BACK FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORD

This form see Department of the Army Pamphlet 738-751 pg 57-58

8/6/2019 Preprint 48 Meses Log Book 1

17/17

EJERCITO NACIONAL

BRIGADA DE AVIACION DATE: Page:1. STATUS 2. SERIAL NUMBER EJC 3. SYSTEM CODE

4. TIME

5. FAULT DATE\TIME 6. FAULT NUMBER

7. FAULTCONTINUA EFECTUAR INSPECCION VARILLAS CONTROLES DE VUELO

8.STA

9. RELATED MAINTENANCE ACTIONS 10.ACTION 11. PID12.MANTT

LEVEL13. MMH

XRmvd Cotter Pin securing self-retaining bolt on Tail RotorQuadrant Pushrod To tail rotor quadrant

XRmvd self-retaining bolt and hdwr securing Tail Rotor QuadrantPushrod To tail rotor quadrant

XRmvd cotter pin securing flat head bolt on Tail Rotor Quadrant

Pushrod To tail rotor quadrant

XRmvd flat head bolt ,short bushings, washers and nut securing

Tail Rotor Quadrant Pushrod To tail rotor quadrant

XRmvd cotter pin securing bolt (1 1/16) on Tail Rotor Quadrant

Pushrod To tail rotor quadrant

XRmvd bolt (1 1/16),long bushing, washers and nut securing TailRotor Quadrant Pushrod To tail rotor quadrant

X Removed Tail Rotor Quadrant Pushrod from tail rotor quadrant

XLoosened rod end jamnut securing Tail Rotor QuadrantPushrod To tail rotor quadrant

X Removed rod end from Tail Rotor Quadrant Pushrod

X Removed jamnut from adjustable rod end

X Dissembled Tail Rotor Quadrant Pushrod tube assembly

FOD and tool check

DA FORM 2408-13-2 RELATED MAINTENANCE ACTIONS RECORDThis form see Department of the Army Pamphlet 738-751 pg 57-58