Putzmeister Mörtelmaschinen GmbH Catalogue 201 … Mörtelmaschinen GmbH Catalogue 201 0/ 2011 ......

Putzmeister Mörtelmaschinen GmbH

Max-Eyth-Straße 10 · D-72631 Aichtal · GermanyP. O. Box 2152 · D-72629 Aichtal · Germany

Telephone +49 (0 ) 71 27 599-0Telefax +49 (0 ) 71 27 599-743

Internet www.mortarmachines.comeMail [email protected]

MM 2599/10 GB

Putzmeister M

örtelmaschinen Gm

bH Catalogue 2010/2011 Machines Accessories Spare parts Tools

MM 2599/10 GB

Catalogue 2010/2011

Plastering machines, screed pumps and fine concrete pumps

2 139

Our catalogue as an aid to work

This year‘s complete catalogue of more than 140 pages will show you the complete range at Putzmeister Mörtelmaschinen GmbH.

Here you will find all our products: floor screed pumps, plastering machines, small fine concrete pumps and of course all the right accessories and tools.

For Dynajet® high-pressure cleaners, we issued a separate catalogue (MM 3474) as well as for fine plastering machines and paint pumps (MM 3682). Please feel free to request a copy.

Easy to search for, easy to find

Every machine chapter starts with a practical summary table. Here we guide you from the application to the right machine. So you will know which machine/accessories is the right one for you.

Each machine is described in detail, with all its important technical data. Here we ask you to note that we have to reserve the right to make technical changes, and also that the performance details are guideline figures and are therefore subject to alteration. We also show you the accessories applicable in each case, so that you always have a complete overview. Technical data may be changed without prior notice.

Please note:

We are grateful for ideas and suggestions on how we can improve the way we design the catalogue even better in the future. Simply write to:

Putzmeister Mörtelmaschinen GmbHSubject “Catalogue”Max-Eyth-Straße 10D-72631 Aichtal · Germany

And if you want to know more about us, just get in touch:Telephone +49 (0) 71 27 5 99-0

Or pay us a visit on the Internet: www.mortarmachines.com

Issue: April 2010

MM 2599/10 GB MM 2599/10 GB

Caveat:

We reserve the right to increase the number of DIN parts and tools per order to minimize the internal costs of storage and packaging.

For a safe and correct operation of the machine please refer to the appro-priate operating manual.

33MM 2599/10 GB

General overview 4 - 9

Overview Trans Mix 10 - 11

Screed pump application overview 12 - 13

Self levelling screed pumps

SP 11 14 - 15SP 20 16 - 17

Pneumatic conveyor

M 760 18 - 19M 740 20 - 21M 730 22 - 23 M 710 24 - 25M 700 26 - 27M 500 28 - 29 Suggested accessories for pneumatic conveyors 30 - 31

Fine concrete pump application overview 32 - 33

Fine concrete pumps

P 715 34 - 35Suggested accessories for P 715 36 - 39P 718 40 - 41Suggested accessories for P 718 42 - 45

Plastering machine application overview 46 - 47

Mixer pumps

MP 10 / MP 12 48 - 49MP 22 50 - 51Suggested accessories for MP 22 52 - 53MP 25 MIXIT / MP 25 FMP 60 54 - 55Suggested accessories for MP 25 56 - 59

Conveying systems

FA 400 / FAT 400 / FA 420 / FAT 420 60 - 61

Mortar spraying systems

Sprayboy P 12 62 - 63Suggested accessories for Sprayboy P 12 64 - 65SP 5 66 - 67Suggested accessories for SP 5 68 - 69S 5 70 - 71Suggested accessories for S 5 72 - 75CM 528-20 76 - 77SP 11 Beliso series 78 - 81Suggested accessories for SP 11 Beliso series 82 - 83P 13 84 - 85Suggested accessories for P 13 86

Accessories for screed pumps 87 - 95

Accessories for fine concrete pumps 96 - 101

Accessories for plastering machines 102 - 123

General accessories 124 - 125

Tools 126 - 133

We are there for you 134 - 135

Conditions of sale and delivery 136 - 137

Table of Contents

4 54MM 2599/10 GB MM 2599/10 GB

A total of 9000 m2 of spaceis available for the production of Putzmeister mortar machines in Aichtal.

…in Aichtal, near Stuttgart. This is where our headquarters are located – but our ideas for technical solutions are formulated on construction sites. That's where it's all about making work easier and more efficient.

Whether you're working with mortar, screed, fine concrete, or paint, we can help with mixing, pumping, application, and spraying tasks. Practical innova-tions have made us great. And our machines are used throughout the world.

Putzmeister Mörtelmaschinen GmbH

develops, produces, and delivers one of the world's most extensive ranges of powerful, site-optimised plastering machines and screed conveyors as well as professional Dynajet high-pressure cleaners.

As a wholly-owned subsidiary of the Putzmeister Group, we are able to offer you, our customers and sales partners, ideal conditions when it comes to expertise, investment security and optimum service in all sectors.

Our pressure vessels are welded at our own works using precise robotics and are then thoroughly checked using ultrasound methods.

Quality guarantee: Our machines only use parts which have passed the most stringent quality controls and in-depth testing.

Aichtal: 21,500 m² of space for producing excellent Putzmeister quality

Extremely modern production facilities in Aichtal

The new assembly hall makes use of a line production system which is linked to numerous throughput stations.

The production plant in Aichtal near Stuttgart offers 9000 m2 of extremely modern facilities for the production of compressed air conveyors, mixing pumps, piston pumps, worm pumps, and the entire professional high-pres-sure cleaning range of the Dynajet brand. All work steps are standardised and guarantee consistently great quality with regard to processing and the performance of the finished products.

Quality Assurance

Our quality management measures start with the vitally important selection of ISO-certified suppliers and continue with the regular checking of these suppliers.

Each machine is started up and tested immediately after assembly. If the test is successful, it is sent on for a final inspection.

During the final production inspection, each machine is optimally adjusted one last time. We test our machines in continuous operation, checking all functions such as safety devices. In this way, we ensure that you receive a reliable Putzmeister product in perfect condition.

Finishing: Not one single machine leaves our production hall without being subjected to a thorough final inspection and careful cleaning.

The Putzmeister Group

We form part of the globally active Putzmeister group. With several subsi-diaries throughout the world, the Putzmeister Group is represented on all global markets and is a real international player.

Our main focuses are on the manufacture of machines for the distribution of concrete, mortar, and high-density substances. In this way, companies of the Putzmeister group are active in business segments in many different areas: Concrete pumps Plant engineering Tunnelling machinery Large robot technology Mortar machines High-pressure cleaners Coating technology (fine plastering machines and paint pumps)

The Putzmeister group: at home all over the world

Technology with more value

However, sophisticated technology isn't everything: In addition, we try to make sure that our contact with customers, sales partners, and suppliers is pleasant and beneficial for both sides.

Area-wide network of competent and helpful sales partners Good quality, comprehensible technical documents A willingness to listen to questions or problems Fast, uncomplicated order processing Quick delivery times for machines and replacements/wearing parts Friendly and competent employees Fair pricing

Investing for the future

We also want to meet both our and your expectations in the future. This is why we continuously invest in qualified and committed employees. Excellent quality is simply not possible without them.

We consistently continue to back the latest computerised plants and technology. Without them, it simply would not be possible to develop and manufacture top-quality products and to deliver them without faults.

We also intensively cultivate contacts with our customers, suppliers and sales partners throughout the world.

Countless honours and awards are a testament to the pioneering role of the Putzmeister group and the vision of our company founder Karl Schlecht.

Welcome to Putzmeister... Quality “Made in Germany”

6 7MM 2599/10 GB MM 2599/10 GB

Fine concrete pumps

for pumping anhydrite, cement and cementite self levelling floor screed, shotcrete, as well as fine concrete with up to 32 mm granulation

Floor screed pumps

for self levelling floor screed and traditional cement screed, for mixing and conveying materials like sand and gravel to pourable and fine concrete

Putzmeister Mörtelmaschinen GmbH is pleased to present one of its most extensive ranges of machines: from the versatile plastering machines, such as our mixer and worm pumps, to state-of-the-art floor screed conveyors and our small fine plaster spraying and paint pumps, and beyond to our sturdy fine concrete piston pump.

We can provide you with the right machine and suitable accessories for virtually all applications.

In operation anywhere and at any time ... ... worldwide

Some of the illustrations show snapshots which do not always comply with the regulations of the Industrial Employers' Liability Insurance Association.

8 9MM 2599/10 GB MM 2599/10 GB

In operation anywhere and at any time ... ... worldwide

Plastering machines

for plaster made from sand, lime and cement, as well as mortar, available in different versions and performance levels for various applications within the civil engineering and construction industries

Some of the illustrations show snapshots which do not always comply with the regulations of the Industrial Employers' Liability Insurance Association.

10 11

Trans Mix ...

MM 2599/10 GB MM 2599/10 GB

Whatever you need, you will find the right “conveying factory” for your needs from amongst our numerous Trans Mix models. Here are some of the possible configurations:

12 variants for the highest possible degree of flexibility

A tilt system is used for the Trans Mix 3200 and 5500. The multiple cham-ber silo facility is hydraulically propped and moved into the mixing cham-ber using a screw conveyor. The material then falls down to the pump in the conveying container. Alternatively, the Trans Mix 400 and 500 models works with integrated delivery units which transport the material within the plant without tilting.

The Trans Mix 3200 and 5500 systems are tilting systems. They differ in the pump system used and are each available in 2 variants: The 3200FE uses a worm pump to convey liquid screed. The 5500ZE uses a compressed air conveyor to convey cement screed.

In addition, the semi-trailer versions of the 3200 and 5500 are each available as an “ST” variant for polystyrene insulation.

The Trans Mix 400 and 500 models do not tilt. Instead, they have integrated delivery units. They can be fitted with three different pump systems: An FE version, with a worm pump for conveying liquid screed A ZE version, with a compressed air conveyor for processing cement screed An LB version, with a piston and worm pump for conveying lightweight concrete

Fully automatic mixing and conveying - easy and universal

Trans Mix systems are mobile mixing and delivery systems for making and conveying liquid screed, traditional cement screed, anhydride screed, and lightweight concrete. All necessary materials such as water, sand, binder, polystyrene insulation, fibres, and liquid concrete additives are stored on board in spe-cial repositories. They are automatically metered, mixed, and conveyed in the Trans Mix as required at the construction site.

Optimum convenience and versatility

Mobile Trans Mix systems have numerous advantages which are not easy to find in other systems:

All materials can be carried on board Very short setup times at the construction site Completely automatic metering and mixing of material to be conveyed Low processing time for material of higher quality Recipes for automatic mixes can be stored in the system Consistent mixes Significantly higher output than with a conventional machine No residue; the Trans Mix simply carries it off again Reduced costs thanks to cost-effective purchase of raw materials Lower personnel requirements: Can be operated by a single person Tailored, easy billing using machine software

Semi-trailer or 8x4 truck system

Nearly all Trans Mix systems are available either as a semi-trailer for your own tractor unit or as an 8x4 truck system with 4 driven wheels. The latter variant is particularly suitable for cramped construction sites. The Trans Mix semi-trailers do not require a tractor unit, but can be operated on their own.

The right Trans Mix system for every application

For detailed information on all Trans Mix models, see www.transmix.de

... the “screed factory on wheels”

The Trans Mix 8x4 versions are especially suited for urban work due to their smaller wheelbase.

Thanks to the large loading capacities, the semi-trailer version Trans Mix 500 and the 8x4 version Trans Mix 400 are particularly ver-satile. And, because they have an integrated delivery system, they can be used in places where tipping is not possible.

A fully automatic mixing process guarantees consistent quality with exact metering and weighing.

No shortages, no residue – the Trans Mix 5500 carries everything you need for on-site work along with it and takes away anything that's left over.

A liquid screed specialist thanks to a powerful worm pump: The Trans Mix 3200FE.

The semi-trailer versions are completely functional without a tractor unit.

One person can load the Trans Mix system.

12 13

– – –

– – – –

– – – –

– – – –

– –

– – – –

– –

– – – –

– –

–

MM 2599/10 GB MM 2599/10 GB

For small or large construction sites, for fine or coarse materials, for short or long delivery distances: Putzmeister machines achieve perfor-mance and alleviate the work.

Note: Always use a machine-compatible mortar in combination with machine technology. If you have any questions, please contact the material manufacturer or contact us directly.

Machines for floor screed, gravel, sand or concrete conveying

Mixer pumpsMP 22 Pages 50-53

MP 25 Pages 54-59

Conveying unitsFA 400 / FA 420 Pages 60-61

Worm pumpsS 5 Pages 66-69

Piston pumps

P 715 P 718 Pages 34-45

Ideal Conditional Not suitable

Pneumatic conveyorsM 760/ M 740/ M 730/ M 710/ M 700/ M 500 Pages 18-31

SP 11 BMR / BMB / BMT

SP 11 BUR / BBR Pages 78-83

SP 11 BHF/ SP 20 DHF Pages 14-17

P 13 Pages 84-85

www.mortarmachines.comwww.mortarmachines.com

Conventional floor screed Self levelling floor screed

Dry mixed mortar Construction site mix Dry mixed mortar Ready mixed mortar Construction site mix grain up to 8 mm grain up to 16 mm grain up to 4 mm grain up to 8 mm grain up to 8 mm

Application overview floor screed pumps

14 15MM 2599/10 GB MM 2599/10 GB

Special feature Basic version Comfort With hydraulic hose drumMachine model hydraulic worm pumpPumpe worm pump 2L75 Theor. delivery rate* 0-15 m3/h 0-15 m3/h 0-15 m3/hDelivery pressure 20 bar 20 bar 20 bar Drive motor 4-cylinder-Kubota diesel engine, 22.7 kW at 2,600 rpmChassis without brakes with brakes, roadworthyHopper volume 220 l 220 l 220 lSupport load 30 kg 30 kg 70 kgWeight 740 kg 740 kg > 750 kgLength 3,210 mm without tow-bar 3,210 mm without tow-bar - 3,519 mm with tow-bar 3,519 mm with tow-bar 3,930 mm with tow-barWidth 1,420 mm 1,420 mm 1,420 mmHeight 1,150 mm 1,150 mm 1,160 mmFilling height 600 mm 600 mm 880 mmMaximum grain size 8 mm 8 mm 8 mmDischarge connection M 50 M 50 M 50Part no. 111 505.440 111 505.420 on request

SP 11 BHF – Comfort

The SP 11 BHF Comfort is the same as the SP 11 BHF, but with remote control for convenient delivery rate regulation and switching the machine on and off.

Part no. 111 505.420

SP 11 BHF – with hose drum

The equipment is identical to that of the SP 11 BHF. However, this model also has a hydraulic hose drum to enable the easy transportation of DN 50 hoses of up to 30 m in length.

On request

Please ask if you require electrical versions of the SP 11 or additional information.

Part Part no. Radio remote control on / off 211 845.009 Radio remote control 498 231 with output regulation Grid screen MW 10 524 209 Torque arm for stator 213 326.005 DIN trailer coupling ring (truck) brakeless 212 154.003 Vibrator 12 V DC 445 484 Working light 437 116

Supplementary equipment

Worm Pump SP 11 BHF

The machine for self levelling floor screed from truck-mixer and continuous mixer

Worm pumps

SP 11 BHF

Large hopper Powerful diesel engine Hydraulically driven reversible worm pump Infinitely variable delivery rate Modern, hard-wearing plastic hood Simple operation via cable remote control or directly at the control console PLC control high pressure water cleaner safety grid screen with 15 mm opening and 12 volt vibrator

Standard equipment: pressure gauge in pressure connection, operating instructions, spare parts list, standard tools, 60 m remote control cable on cable drum, ball hitch

Part no. 111 505.440

Self levelling floor screed pumps

Technical data SP 11 BHF SP 11 BHF SP 11 BHF

A modern diesel engine with integrated hydraulic system supplies the SP 11 with sufficient power at all speeds.

You can control all machine functions conveniently from the central control panel.

The powerful, low-wearing worm pump 2L75.

* The delivery rate depends on the rotor / stator, pump speed (rpm) and pumping media. The delivery rate may be higher or lower.


The lightweight SP 11 BHF is compact, manoeuvrable and powerful yet quiet during operation. It is the worm pump for floor screed professionals.

Suitable for pumping material with 0-8 mm grain size, e.g. self leveling anhydrite floor screed and cement floor screed, etc. A truck mixer or other external mixers supply the machine with wet mixes.

Part Part no. Fig. 2x Delivery hose ID 50mm, V50, M50 20m 501 915 1 5x Sponge rupper ball ID 50 000 212.005 2 5x Sealing ring ID 50 213 266.000 3 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Hose holder made of leather 000.206.008

Suggested accessories for self levelling floor screed:

SP 11 BHF

Further information is available in brochure MM 3968.For additional accessories see page 102 ff.

16 17MM 2599/10 GB MM 2599/10 GB

Machine model hydraulic worm pumpPump worm pump 7515 worm pump 2L8Theor. delivery rate* 15 m3/h 18 m3/hDelivery pressure 35 bar 25 barDrive motor 3-cylinder diesel engine, Deutz, 32.8 kW at 2,600 rpmChassis robust T-chassis, with brakesHopper volume 250 l 250 lSupport load 45 kg 45 kgWeight 960 kg 960 kgLength 4,200 mm with tow-bar 4,200 mm with tow-barWidth 1,300 mm 1,300 mmHeight 1,280 mm 1,280 mmFilling height 1,000 mm 1,000 mmMaximum grain size 8 mm 12 mmDischarge connection V 50 V 50Part no. H 872 044.100 H 872 044.120

Technical data SP 20 DHF SP 20 DHF

The diesel engine with an impressive output of 32.8 kW. You can operate the SP 20 cpl. from one side, or using the convenient radio remote control.

The new wear-resistant worm pumps, type 2L8.

Part Part no. Electric vibrator placed outside the material hopper H 872 040 9010 Signalling device on the machine, horn H 317 711 0317 (only with radio remote control) Signalling device on the machine, indicator lamp H 317 711 0324 Radio remote control H 317 711 0333 Cable drum with remote control H 872 020 1290 Diesel particle filter H 872 040 0310 Battery for radio transmitter H 317 711 0362 Connecting adapter with pressure gauge H 872 020 1300


Worm Pump SP 20 DHF

Unbeatable in pump performance and low in wear

Worm pumps

A professional self levelling floor screed worm pump. Hydraulically driven with an infinitely adjustable pumping rate up to 18 m3/h, it is the worm pump for the self levelling floor screed professional – compact, powerful and soundproofed.

Grains up to 8 mm, even over-size up to 12 mm are no problem for this pump, e.g. anhydrite, cementrite, cement self levelling floor screed etc. The SP 20 should only be fed by truck-mixers.

SP 20 DHF

Powerful engine Worm pump with hydraulic pump drive Reversible worm pump 7515 or 2L8 Infinitely variable delivery rate, even from the hose end Infinitely variable mixer speed Storage space for spare worm pump Storage space for tools Large hopper Tilting sieve insert with 15 mm opening

Standard equipment: pressure-gauge in pressure connection, operating instructions, spare parts list, standard tools, overrun braking device with ball hitch.

Part no. H 872 044.100Part no. H 872 044.120

* The delivery rate depends on the rotor / stator, pump speed (rpm) and pumping media. The delivery rate may be higher or lower.

www.mortarmachines.comwww.mortarmachines.com Self levelling floor screed pumps

Part Part no. Fig. 2x Delivery hose ID 50mm, V50, M50 20m 519 915 1 5x Sponge rupper ball ID 50 000 212.005 2 5x Sealing ID 50 213 266.000 3 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Hose holder made of leather 000.206.008

Suggested accessories for self levelling floor screed:


18 1919

MM 2599/10 GB MM 2599/10 GB

Pneumatic conveyors Floor screed conveyors

The M 760 is our most powerful Mixokret. It is practical, easy to use, and easy to service. Like every Mixokret, this model is suitable for mixing and conveying floor screed, sand, gravel and fine grained concrete with a grain size of up to 16 mm.

M 760 DH

Wear resistant mixing blades Hydraulically driven mixer unit with forward / reverse and overload protection Extremely lightweight, hard-wearing plastic hood Intelligent air control 4-cylinder diesel engine with inline design, fulfils emission standard COM III Solid, reliable chassis Tow bar can be lowered to 20 cm Analogue controls easy to read, protected by a robust flap Mixer drum with variable lid position Efficient vessel venting system Multi-stage low-wearing mixer shaft seal Exchangeable discharge connection for ID 50, 65, 90 Delivery air cut-out autom. central lubrication system working light Lifting ring Integrated 40 l tool box

Standard equipment: ball and ring hitch, operating instructions, standard tools, one discharge stand included. Please specify the required discharge stand when placing your order (see page 30).

Part no. 111 571.010

M 760 DHB

Same as M 760 DH, but with skip for faster, power saving filling of the mixing vessel.

Part no. 111 571.020

M 760 DHBS

Same as the M 760 DHB, but with hydraulically driven and radio remote controlled scraper winch with 11 m hauling rope and practical rope guide mounted on the skip.

Part no. 111 571.030

Part Part no. Hydraulically driven high-pressure cleaner installation 484 438 kit, up to 140 bar operating pressure, with spray gun and 8 m high-pressure hose Mixing time adjustment 5-30 sec. 495 393 protection vessel including all WPs 002 737.009 Trailer lighting 24 V 503 616 Mix counter 489 515 Individual painting – (hood paint, no metallic-paint) on request Special labelling, with logo and 1-colour text on request Other labelling on request Service package 500 h 502 366 Service package 1,000 h 504 207 Navigation and fleet management system 504 627 Vehicle cable adapter 7 - 13 pin, 12 V 437 679 Vehicle cable adapter 13 - 7 pin, 12 V 248 012.009 Mechanical water metering 531 014 Exhaust system with particle filter on request

For accessories and hose packages, see page 30.


The diesel engine has an inline design for a tidier appearance and improved layout.

The control panel is well laid out and protected by a robust flap.

260 l mixing vessel; 200 l volume; max. perm. 8 bar vessel pressureSpecial feature basic version with skip with skip and scraperTheor. delivery rate* 4 m3/ h 4.8 m3/ h 5 m3/ hDelivery pressure 7 bar 7 bar 7 barDelivery distance* 200 m horizontally, 50 storeys highCompressor 5.0 m3/ min, switch-off pressure 7 barDrive motor D 2011 L04 4-cylinder Deutz diesel-engine, 46.5 kW at 2.600 rpm (Emission category III A)Chassis fully galvanised chassis with adjustable coupling height (20 - 80 cm), robust T-chassisWeight (tank full) 1,600 kg 1,820 kg 1,900 kgLength 4,820 mm 4,820 mm 4,820 mmWidth 1,500 mm 1,500 mm 1,500 mmHeight 1,600 mm 1,600 mm 1,600 mm Loader height (vertical) – 2,480 mm 2,830 mm with scraperFilling height 820 mm 600 mm 600 mmMaximum grain size 16 mm 16 mm 16 mmDischarge connection KKV 70 KKV 70 KKV 70Skip volume 260 l 260 l 260 l Part no. 111 571.010 111 571.020 111 571.030

Technical data M 760 DH M 760 DHB M 760 DHBS

* The data is based on experience and is dependent on the materials used.

Mixokret M 760 DH, M 760 DHB, M 760 DHBS

The most powerful Mixokret ever – with 46 kW powerful diesel engine and hydraulic drive


Mixokret M 760 DH

Mixokret M 760 DHBS

Further information is available in brochure MM 3909.For suggested accessories for various applications see pages 30-31. For additional accessories see page 87 ff.

You can select the position of the lid on the mixing vessel as required.

20 2121MM 2599/10 GB MM 2599/10 GB


Part Part no. Hydraulically driven high-pressure cleaner installation 484 438 kit, up to 140 bar operating pressure, 600 l/ h, spray gun, 8 m high-pressure hose (only for M 740 DB + M 740 DBS) protection vessel including all WPs on request Mixing time adjustment 5-30 sec. 495 393 Trailer lighting 24 V 503 616 Mix counter 489 515 Individual painting – hood (RAL paint, no metallic-paint) Special labelling, with logo and 1-colour text Other labelling on request Service package 500 h 493 689 Service package 1,000 h 504 208 Navigation and fleet management system 504 627 Vehicle cable adapter 7 - 13 pin, 12 V 437 679 Vehicle cable adapter 13 - 7 pin, 12 V 248 012.009 Mechanical water metering 531 014 Exhaust system with particle filter 002 737.009


M 740 DB

Same as M 740 D, but with loader for faster, power sparing filling of the mixing vessel.

Part no. 111 570.220

M 740 DBS

Same as M 740 DB, but with hydraulically driven and radio or cable remote controlled scraper winch with 11 m hauling rope and practical cable guide mounted on the loader. Cable remote control available as alternative to radio remote control.

Part no. 111 570.230

The M 740 is the most successful screed conveyor in Europe. It is easy to use, easy to service, and stylish. This real allrounder is suitable for mixing and conveying floor screed, sand, gravel and fine grained concrete with a grain size of up to 16 mm.

M 740 D

Wear resistant mixing blades Extremely lightweight, hard-wearing plastic hood Intelligent air control 3-cylinder diesel engine with inline design, fulfils emission standard COM III Solid, reliable chassis Tow bar can be lowered to 20 cm Analogue controls easy to read, protected by a robust flap Mixer drum with variable lid position Efficient vessel venting system Electro-pneumatic engagement and disengagement of the V-belt on the mixer drive Multi-stage low-wearing mixer shaft seal Exchangeable discharge connection with ID 50, 65, 90 Delivery air cut-out Autom. central lubrication system working light Lifting ring Integrated 40 l tool box

Standard equipment: ball and ring hitch, operating instructions, standard tools, one discharge stand included.Please specify the required discharge stand when placing your order (see page 30).

Part no. 111 570.210


260 l mixing vessel; 200 l volume; max. perm. 8 bar vessel pressureSpecial feature basic version with skip with skip and scraperTheor. delivery rate* 3.8 m3/h 4.6 m3/h 5 m3/hDelivery pressure 7 bar 7 bar 7 barDelivery distance* 180 m horizontally, 30 m highCompressor 4.3 m3/ min; switch-off pressure 7 barDrive motor D 2011 L03 3-cylinder Deutz diesel-engine, 31.5 kW at 2,300 rpm (emission category III A)Chassis fully galvanised chassis with adjustable coupling height (20 - 80 cm), robust T-chassisWeight (tank full) 1,564 kg 1,786 kg 1,872 kgLength 4,605 mm 4,800 mm 4,800 mmWidth 1,500 mm 1,500 mm 1,500 mmHeight 1,585 mm 1,585 mm 1,585 mmLoader height (vertical) – 2,483 mm 2,820 mm with scraperFilling height 820 mm 600 mm 600 mmMaximum grain size 16 mm 16 mm 16 mmDischarge connection KKV 70 KKV 70 KKV 70Skip volume 260 l 260 l 260 lPart no. 111 570.210 111 570.220 111 570.230

Technical data M 740 D M 740 DB M 740 DBS

You can select the position of the lid on the mixing vessel as required. The M 740 has a powerful 3-cylinder diesel engine.

The control panel is well laid out and protected by a robust flap.

Mixokret M 740 D, M 740 DB, M 740 DBS

The easy-to-use Mixokret with modern plastic hood

Mixokret M 740 D

Mixokret M 740 DBS




22 23

23

MM 2599/10 GB MM 2599/10 GB


The hydraulically driven M 730 combines all benefits of the Mixokret in the smallest of spaces. The small Mixokret is the ideal machine for small crews and lightweight tractor units and is perfect for mixing and conve-ying floor screed, sand, gravel and fine grained concrete with a grain size of up to 16 mm.

M 730 DH

Wear resistant mixing blades Hydraulically driven mixer unit with forward/backward run and overload protection Extremely lightweight, hard-wearing plastic hood Intelligent air ducts 3-cylinder diesel engine Solid, more reliable chassis Tow bar can be lowered to 20 cm Analogue controls easy to read, protected by a robust flap Mixer drum with variable lid position Efficient vessel venting system Multi-stage low-wearing mixer shaft seal Exchangeable discharge connection with ID 50, 65 Delivery air cut-out Autom. central lubrication system working light Lifting ring Integrated 40 l tool box

Standard equipment: ball and ring hitch, operating instructions, standard tools, one discharge stand included. Please specify the required discharge stand when placing your order (see page 30).

Part no. 111 572.010

M 730 DHB

Same as M 730 DH, but with hydraulically-operated skip with 150 l volume.

Part no. 111 572.020

Mixokret M 730 DH, M 730 DHB

The “lightweight version” of our pneumatic conveyors

Part Part no. Mixing time adjustment 5-30 sec. 495 393 protection vessel including all WPs on request Trailer lighting 24 V 503 616 Individual painting – hood (RAL paint, no metallic paint) on request Special labelling, with logo and 1-colour text on request Mix counter 489 515 Other labelling on request Navigation and fleet management system 504 627 Vehicle cable adapter 7 - 13 pin, 12 V 437 679 Vehicle cable adapter 13 - 7 pin, 12 V 248 012.009 Mechanical water metering 531 014



200 l mixing vessel, 150 l volume; max. perm. 6 bar vessel pressureSpecial feature basic version with skipTheor. delivery rate* 2.5 m3/h 3.0 m3/hDelivery pressure 6 bar 6 barDelivery distance* 80 m wide, 45 m highCompressor 2.7 m3/min; switch-off pressure 7 barDrive motor 3-cylinder Kubota-diesel engine, 24 kW at 2,400 rpmChassis fully galvanised chassis with adjustable coupling height (20 - 80 cm), robust T-chassisWeight (tank full) 1,200 kg 1,300 kgLength 4,500 mm 4,610 mmWidth 1,500 mm 1,500 mmHight 1,880 mm 1,580 mmLoader height (vertical) – 2,450 mm Filling height 820 mm 600 mmMaximum grain size 16 mm 16 mmDischarge connection KKV 89 KKV 89Skip volume 150 l 150 lPart no. 111 572.010 111 572.020

M 730 DHB with HPC**: Part no. 111 572.030

Technical data M 730 DH M 730 DHB

The M 730 has a powerful 3-cylinder diesel engine.

The LED working light is a standard series accessory fitted to the rear of the Mixokret.

The discharge connection can be exchanged to match the diameter of the delivery hose.

* The data is based on experience and is dependent on the materials used.** HPC = High pressure cleaner

Mixokret M 730 DHB



24 2525MM 2599/10 GB MM 2599/10 GB

The M 710 EBS is the convenient, electrically powered alternative to the M 700 E. This product range is fitted with a hydraulic skip and a hydrauli-cally driven scraper with cable remote control.

The machine is suitable for conveying floor screed, sand, gravel and fine grained concrete with up to 16 mm grain size.

M 710 EB

Electric mixer drive with geared motor Multi-stage, low-wearing PM mixer shaft seal Low-wearing mixing blades made from special chromium cast Vessel lid with safety lock mechanism and safety grid Large vessel venting system Lifting ring Replaceable discharge connections for hoses with ID 50, 65 or 90 detachable ring hitch Hydraulically driven skip

Standard equipment: operating manual, standard tools, one discharge stand included. Please specify the required discharge stand when placing your order (see page 30).

Part no. 111 597.020

M 710 EBS

Identical to the M 710 EB but with a hydraulically driven, cable-controlled scraper winch with an 11 m pull cable and cable guide.The cable guide is fitted on the loader.

Part no. 111 597.004

Special voltage configurations are available on request.

Mixokret M 710 EB, M 710 EBS

The convenient model “without“ a compressor

Pneumatic conveyors

Part Part no. protection vessel including all WPs 002 737.009 High-pressure cleaner installation kit, 422 351 140 bar with spray gun and 8 m high-pressure hose central lubrication system on request



Floor screed conveyors

The operating panel has a simple and clear design. It is easily accessible and loca-ted outside the working zone which is prone to dirt.

The M 710 has a powerful 7.5 kW electro-drive.

Depending on the connection of the required hose (ID 50, 65 or 90), it is easy to replace the discharge con-nection.

260 l mixing vessel, 200 l volume, max. perm. 8 bar vessel pressureSpecial feature with skip with skip and scraper Theor. delivery rate* 4 m3/h 4 m3/h Delivery pressure 7 bar 7 bar Delivery distance* 120 m horizontally, 60 m high 120 m horizontally, 60 m high Compressor additional compressor for construction sites minimum, 4 m3/ min; 7 bar operating pressure**Drive motor electric motor 7.5 kW, 400 V 3-phase current, 50 Hz., star-delta automatic start, socket CEE 32Chassis not approved for road use not approved for road use Skip volume 260 l 260 l Weight 1,150 kg 1,200 kg Length 2,600 mm 2,600 mm Width 1,320 mm 1,320 mm Height 1,300 mm 1,300 mm Loader height (vertical) 2,370 mm 2,370 mm Filling height 600 mm 600 mm Maximum grain size 16 mm 16 mm Discharge connection KKV 70 KKV 70 Part no. 111 597.020 111 597.004

Technical data M 710 EB M 710 EBS

* The data is based on experience and is dependent on the materials used as well as on the air volume and the compressor.** Recommended air volume 4 m3/ min. If you use higher air volume you can increase the delivery distance.


Mixokret M 710 EBS


26

2727


Part no. 111 599.002


Pneumatic conveyors

Mixokret M 700 E

The M 700 E is especially ideal for building contractors using their own compressors

The Mixokret M 700 E is the basic model of the Mixokret floor screed con-veyor range. It is by far the smallest and lightest Mixokret by Putzmeister.

In the M 700 E, our engineers consistently paid attention to obtaining a sim-ple and robust design, that is suitable for tough everyday conditions. Theresult is the cost-effective Mixokret by Putzmeister, which offers everything that is required on a modern construction site.

The machine is suitable for conveying floor screed, sand, gravel and fine grained concrete with up to 16 mm grain size.

M 700 E

powerful electric motor Low-wearing mixing blades Low-wearing PM mixer shaft seal Replaceable discharge connections for hoses with ID 50, 65 or 90 Vessel lid with safety lock mechanism and safety grid Large vessel venting system Mixer drum with variable lid position EWO coupling to connect additional air-operated devices master air valve to start or stop delivery Grid safety switch Lifting ring Ring hitch

Part Part no. Power cable 4 x 6 mm2, 062 922.003 25 m long, coupling 32/32 Central lubrication system for the on request bearing of the mixer shaft on request protection vessel including all WPs on request 002 737.009



260 l mixing vessel, 200 l volume; max. perm. 7 bar vessel pressureSpecial feature basic version Theor. delivery rate* 4 m3/h Delivery pressure 7 bar Delivery distance* 120 m horizontally, 60 m highCompressor extra site compressor with 4 m3/min (minimum 2.5 m3/min) and 7 bar operating pressure**Drive motor electric motor 7.5 kW, 400 V 3-phase 50 Hz, 16 A fuse, socket CEE 32Chassis not approved for road use Weight 700 kgLength 2,670 mm Width 1,280 mmHeight 1,190 mmFilling height 860 mmMaximum grain size 16 mmDischarge connection KKV 70Part no. 111 599.002

* The data is based on experience and is dependent on the materials used as well as on the air volume and the compressor.** Recommended air volume 4 m3/min. If you use higher air volume you can increase the delivery distance.

Technical data M 700 E


The mixing vessel vent is large, easy to operate and works reliably.

The discharge connection can be easily replaced for the connection of ID 50, 65 or 90 hoses.

The powerful 400 V electric motor has a power of 7.5 kW. It is robust, quiet and nearly wearfree.

Mixokret M 700 E

MM 2599/10-GB MM 2599/10-GB



28 2929MM 2599/10 GB MM 2599/10 GB

Pneumatic conveyors

Mixokret M 500 E

The powerful screed conveyor with electric drive

The Mixokret M 500 E offers top performance in all areas. With a capacity of 640 l, it has the biggest mixing vessel in the entire Mixokret range, which allows for longer delivery intervals.

In addition, it is the only Mixokret that can convey screed, sand, fine conrete, styrofoam underlayment, leightweight concrete with expanded aggregates or pumice concrete up to a grain size of 32 mm.

M 500 E

powerful electric motor, star-delta automatic start Low-wearing mixing blades Low-wearing mixer shaft seal Hand hole in vessel Vessel lid with safety lock mechanism and safety grid Mixer drum with variable lid position Large vessel venting system Replaceable discharge connections for hoses with ID 50, 65 or 90 central air lock to start or stop delivery Geka coupling to connect additional air-operated devices Ring hitch Lifting ring

Part Part no. Power cable 4 x 6 mm2, 466 270 25 m long, coupling 63 / 63 Central lubrication system for the bearing of the mixer shaft on request Discharge connection ID 90, KKV 108 521 187



640 l mixing vessel, EU-tested, 400 l volume, max. perm. 7 bar vessel pressureSpecial feature basic version Theor. delivery rate* 4 m3/h Delivery pressure 7 bar Delivery distance* 120 m horizontally and 60 m highCompressor extra site compressor with minimum 4 m3/min air volume and 7 bar operating pressure**Drive motor electric motor 18,5 kW, 400 V 3-phase 50 Hz, 35 A fuse, CEE 63 socketChassis not approved for road use Weight 1,200 kg Length 3,730 mm Width 1,400 mm Height 1,410 mm Filling height 1,140 mm Maximum grain size 32 mm Discharge connection KKV 70 Part no. 111 598.003

Technical data M 500 E

On the M 500 too, all operating elements are arranged on one side. The operator uses the robust air cock to adjust the Mixokret‘s upper and lower air flow for pumping.

The assembly hand hole in the drum makes it easy to reach all areas for maintenance and servicing.

The mixing vessel vent is large, easyto operate and works reliably.

* The data is based on experience and is dependent on the materials used as well as on the air volume and the compressor.** Recommended air volume 4 m3/min. If you use higher air volume you can increase the delivery distance.


Mixokret M 500 E



Part no. 111 598.003



30 31MM 2599/10 GB MM 2599/10 GB

Part Part no. Fig. 2x ID 50 mm hose, 10 bar, length 20 m 213 451.006 10 1x Discharge stand, tripod, aluminium ID 50 529 743 11 2x O-ring 010 207.000 13 6x Sponge rubber ball, ø 60 mm 000 212.005 14 for delivery hose ID 50 1x Reducer piece ID 65, KKV 70/ ID 50 071 790.006 2x Rectangular gasket 213 266.000 optional: 1x ID 50 mm hose, 10 bar, length 10 m 213 450.007 9 1x ID 50 mm hose, 40 bar, length 20 m 501 915 10 1x Discharge stand, tripod, steel ID 50 529 740 11 1x Discharge stand, w. skid, steel ID 50 529 746 12 1x Discharge stand, w. skid, aluminium ID 50 529 751 12

Standard delivery line with couplings for Mixokret PM 50 ID 50 mm (up to 8 mm grain size*)

Part Part no. Fig. 8x ID 65 mm hose KK 70, 10 bar, 10 m 456 831 10 1x Discharge stand, tripod, aluminum KKV 70 529 744 11 8x O-ring 010 207.000 13 8x Sponge rubber ball, ø 80 mm 000 246.000 14 for delivery hose ID 65 optional: 1x NW 65 mm hose KK 70, 10 bar, 20 m 456 832 10 1x Discharge stand, tripod, steel KK 70 529 741 11 1x Discharge stand, w. skid, steel KK 70 529 747 12 1x Discharge stand, w. skid, aluminium KK 70 529 750 12

Complete Set, Part no.: 533 089Standard delivery line ≈ 40 m long, consisting of:




Delivery line KK 70 for Mixokret ID 65 mm (up to 12 mm grain size*)

* dependent on the materials used

Delivery line KK 108 for Mixokret ID 90 mm (< 32 mm grain size*)

Part Part no. Fig. 8x NW 65 mm hose KK 89 / HR, 10 bar, 10 m 443 675 9 1x KKV 89 coupling 209 205.004 10 1x Discharge stand, tripod, aluminium KK 89 529 745 11 8x O-ring 002 224.004 13 8x Sponge rubber ball, ø 80 mm 000 246.000 14 for delivery hose ID 65

optional: 1x NW 65 mm hose KK 89 / HR, 10 bar, 20 m 443 672 9 1x Discharge stand, tripod, steel KK 89 529 742 11 1x Discharge stand, w. skid, steel KK 89 529 746 12 1x Discharge stand, w. skid, aluminium KK 89 529 751 12




Accessory equipment for hose sets

Part Part no. Accessories for using hoses 509 001 ID 50, PM50 (including reduction KKM 70, V 50 2x sponge rubber balls, O-rings)

Accessories for using hoses 509 003 ID 65 / KK70 (including sponge rubber balls, O-rings)

Accessories for using hoses 509 006 ID 65 / KK89 (including coupling KKV 89, sponge rubber balls, O-rings)



* dependent on the materials used

Part Part no. Fig. 8x ID 90 hose KK108, 10 bar, 10 m 454 406 13 1x Discharge stand KKM 108 209 811.003 14 1x Special outlet kpl. ID 90, KKV 108 419 634 15 8x Sponge rubber ball, ø 120 mm 016 091.003 16 for delivery hose ID 90 8x O-ring 210 580.006 17

Part Part no. Fig. 8x ID 90 mm hose KK 89, 10 bar, 10 m 455 436 10 1x Discharge stand, w. skid, steel KK 89 529 748 12 8x O-ring 002 224.004 13 8x Sponge rubber ball, ø 120 mm 016 091.003 14 for delivery hose ID 90 1x spezieller Abgang kpl. NW 90, KKV 89 073 640.002 15

optional: 1x Discharge stand, tripod, steel KK 89 529 740 11 1x Discharge stand, w. skid, steel KK 89 529 746 12 1x Discharge stand, w. skid, aluminium KK 89 529 751 12

Suggested Accessoriesfor floor screed conveyors

www.mortarmachines.comwww.mortarmachines.com Accessories for Floor screed conveyors

15

32 33

– – –

– –

– –

–

–

MM 2599/10 GB MM 2599/10 GB

Fine concrete Self levelling floor screed

Fine concrete Fine concrete Fine concrete Shotcrete Ready mixed mortar Construction site mix grain up to ~ 8 mm grain up to ~ 16 mm grain up to ~ 32 mm grain up to ~ 8 mm grain up to ~ 8 mm grain up to ~ 8 mm

For small or large construction sites, for fine or coarse materials, for short or long delivery distances: Putzmeister machines achieve a high performance and alleviate your workload.

Note: Always use a machine-compatible mortar in combination with machine technology. If you have any questions, please contact the material manufacturer or contact us directly.

Machine for pumping fine concrete and self levelling floor screed

Application overview – Fine concrete pumps

Piston pumps

P 13 Pages 84-85

P 715 Pages 34-39

Worm pumpsSP 11 BHF/ SP 20 DHF Pages 14-17

P 718 Pages 40-45



34 35

MM 2599/10 GB MM 2599/10 GB

P 715Compact trailer fine concrete pump for up to 16 mm grain

Piston pumps Fine concrete pumps

Part Part no. Central lubrication system 489 663 Exhaust system particle filter 487 073 Grid screen MW 10 for shotcrete 514 057 Grid screen MW 20, detachable 491 025 Cable remote control, electric, 5 m 435 566 (pump on / off, reverse pumping, emergency off) Radio remote control with transmitter 438 062 and receiver (pump on/ off, reverse pumping, emergency off) Interface cable, 16 pin, 1 m long 436 355 (only for retrofitting) Top for hopper 436 551 High-pressure cleaner, up to 140 bar – installation kit – 526 919 600 l/ h with spray gun and 8 m high-pressure hose Flushing water pump, 20 bar, 50 l/min 439 892 – installation kit – Working light, 12 V, 50 Watt Halogen 462 956 Fuses, spare part package 268 931.005 Ball hitch 213 458.009 Special paint for hood (RAL colour) Additional equipment for pumping 458 584 self-levelling floor screed, side air chamber Remote control cable, 10 m 246 780.003 Remote control cable, 20 m 246 781.002 Remote control cable, 50 m 246 782.001 End pipe with shutter 436 849 Central lifting eye 525 351 13-pin to 7-pin adapter socket 437 679 7-pin to 13-pin adapter socket 248 012.009


The small, light and efficient fine concrete pump trailer for pumping anhy-drite, cement and cementrite self levelling floor screed and fine concrete up to 16 mm. Ideal for shotcreting, pressure pointing mortar and for con-creting work for up to 16 mm grain.

The S-valve allows pump pressures up to 68 bar, and is even seal-proof for slurries and water. Wear that occurs is compensated automatically wtih the automatic ring of the S-valve.

P 715

Diesel or electro-hydraulic drive in steel frame Trailer with DIN hitch (truck) with overrunning brake permitted up to 80 km/ h or as a stationary skid version Plastic engine hood and TARGA hoop Hopper with agitator and rubber collar Folding 30 mm safety grid screen with 12 volt vibrator Safety shutoff for agitator hopper with flap for emptying and cleaning Folding hopper attachment 2-cylinder piston pump with hard-chrome-plated delivery cylinders and a water box between the drive and delivery cylinders to flush the pistons and cool the piston rods It is possible to replace the pistons through the water box Hydraulic control of pump and S-valve. Infinitely variable pumping rate, manually adjustable The maximum pumping pressure can be set to 40 or 68 bar Central lubrication manifold

Standard equipment:cleaning pipe 4.5“ SK, clamp coupling with seal, cleaning accessories and tools, protective helmet (yellow), operating manual and spare parts list

Part no. 111 591.010


Machine type trailer pump stationary pump trailer pump stationary pump Pump 2-cyl. piston pump, hydraulically drivenTheor. delivery rate (piston side) 4 - 17.4 m3/ h 4 - 17.4 m3/ h 4 - 18.2 m3/ h 4 - 18.2 m3/ hDelivery pressure (piston side) 68 bar 68 bar 68 bar 68 barCylinder diameter 150 mm 150 mm 150 mm 150 mmDiameter piston stroke 700 mm 700 mm 700 mm 700 mmStrokes per minute (minimum) 27 27 27 27Drive cylinder diameter 80 / 45 mm 80 / 45 mm 80 / 45 mm 80 / 45 mmDrive motor 3-cyl. diesel engine Deutz F3M 2011, 34.5 kW 30 kW electric motor, 400 V, 50 HzHopper capacity TS 323 (250 l/ 280 l with rubber collar)Chassis 1,900 kg chassis, skid frame with 1,900 kg chassis, skid frame with with brakes mountings for fork-lift with brakes mountings for fork-liftWeight 1,850 kg 1,700 kg 1,800 kg 1,650 kgLength 4,200 mm 3,067 mm 4,200 mm 3,067 mmWidth 1,510 mm 1,393 mm 1,510 mm 1,395 mm Height 1,600 mm 1,395 mm 1,600 mm 1,395 mm Filling height 1,180 mm 973 mm 1,180 mm 973 mmMaximum grain size 16 mm 16 mm 16 mm 16 mmDischarge connection SK 4.5“ SK 4.5“ SK 4.5“ SK 4.5“ Part no. 111 591.010 111 591.080 111 591.060 111 591.070

Technical data P 715 TD P 715 SD P 715 TE P 715 SE

Operation is easy. Everything is well laid out and easy to reach. You can reach all areas for mainte-nance and servicing conveniently, for checking the oil level, for example.

Simply fold the hopper away to the side. The agitator and S-valve are already easily accessible in front.

P 715 TD



3736MM 2599/10 GB MM 2599/10 GB

Delivery line for fine concrete, mortar, self levelling floor screed, SK 50, 60 bar, ≤ 8 mm grain size

Delivery line for fine concrete, mortar, self levelling floor screed, SK 65, 85 bar, ≤ 12 mm grain size

Suggested accessories for P 715

Concrete spray line SK 65 / PM 50 / 3“; max. 40 bar, ≤ 8 mm grain size

Suggested accessoriesfor P 715




Delivery line for mortar, self levelling floor screed, PM 50, 40 bar, ≤ 8 mm grain size


Part Part no. Fig. 4x Clamp coupling SK 4.5“ 431 613 1 4x Seal DN 100, 4.5“ 057 341.000 2 30x Spring cotter 018 878.004 3 2x Elbow pipe SK 100, 4.5“, 90° 421 329 4 1x T-delivery pipe SK 100, 4.5“, 1 m 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 1x Reduction pipe SK 100, 4.5“-SK 65, 3“, 1 m 224 269.009 7


Part Part no. Fig. 11x Clamp coupling SK 3“ 417 798 8 15x Seal DN 65, 3“ 064 084.004 9 8x Delivery hose SK 65, 3“, 5 m 057 886.002 10 1x Reduction pipe SK 65, 3“-SK 50, 3“, 1,000 mm 058 670.000 11 1x Transmission piece 082 784.001 12 1x PM coupling M 50, 2“ 211 600.008 13 1x Mortar hose DN 50 TS PN 40, 13 m 501 914 14 1x Concrete spraying nozzle V 50, 30 mm 072 157.004 15 2x Air hose ¾“, 20 m 416 015 16 6x Sponge rubber ball, ø 65 mm 000 246.000 17 6x Sponge rubber ball, ø 60 mm 000 212.005 18

additional accessories: 1x Lid for T-delivery pipe 057 627.009 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Metering pump for accelerator (silicate): 1x Air hose ¾“, 20 m 416 015 16 1x Silicate metering pump with compressed 002 423.009 19 air drive (barrel pump) with connector 2x High-pressure hose ½“, 20 m 001 983.003 20

Part Part no. Fig. 4x Clamp coupling SK 4.5“ 431 613 1 4x Seal DN 100, 4.5“ 057 341.000 2 5x Spring cotter 018 878.004 3 2x Elbow pipe SK 100, 4.5“, 90° 421 329 4 1x T-delivery pipe SK 100, 4.5“, 1 m 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 1x Reduction pipe SK 100 / 4.5“- SK 65 / 3“, 1.5 m 238 508.002 7 1x Clamp coupling SK 3“ 417 798 8 1x Seal DN 65, 3“ 064 084.004 9 1x Transmission piece SK 50 / RA 2“ 082 784.001 10 1x PM coupling V50 / RI 2“ 205 273.001 11 6x Mortar hose DN 50, 40 bar, 13.3 m 501 914 12 6x Sponge rubber ball, ø 50 mm 000 212.005 13

additional accessories: 1x Lid for T-delivery pipe 057 627.009 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 4x Clamp coupling SK 4.5“ 431 613 1 4x Seal DN 100, 4.5“ 057 341.000 2 55x Spring cotter 018 878.004 3 1x Elbow pipe SK 100 421 329 4 1x T-delivery pipe SK 100, 4.5“, 1,000 mm 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 1x Reduction pipe 100 / 50-4.5“/ 3“, 1,500 mm 238 508.002 7 45x Clamp coupling SK, 3“ 417 798 8 55x Seal DN 65, 3“ 064 084.004 9 4x Elbow pipe SK 50, 3“, 90° 081 777.006 10 2x Delivery pipe SK 50, 3“, 1,000 mm 081 783.003 11 4x Delivery pipe SK 50, 3“, 2,000 mm 081 784.002 12 30x Delivery pipe SK 50, 3“, 3,000 mm 081 785.001 13 4x Elbow pipe SK 50, 3“, 45° 081 779.004 14 1x Delivery hose 3“, SK 50, 3“, 2.000 mm 481 169 15 6x Sponge rubber ball, ø 60 mm 000 212.005 16

additional accessories: 1x Lid for T-delivery pipe, 4.5“ 057 627.009 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 4x Clamp coupling SK 4,5“ 431 613 1 4x Seal DN 100, 4,5“ 057 341.000 2 49x Spring cotter 018 878.004 3 1x Elbow pipe SK 100, 4.5“, 90° 421 329 4 1x T-delivery pipe SK 100, 4.5“, 1,000 mm 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 1x Reduction pipe 100 / 65-4.5“/ 3“, 1,000 mm 224 269.009 7 44x Clamp coupling SK 3“ 417 798 8 44x Seal DN 65, 3“ 064 084.004 9 4x Elbow pipe SK 65, 3“, 90° 057 756.006 10 2x Delivery pipe SK 65, 3“, 1,000 mm 057 727.006 11 4x Delivery pipe SK 65, 3“, 2,000 mm 057 728.005 12 29x Delivery pipe SK 65, 3“, 3,000 mm 057 729.004 13 4x Elbow pipe SK 65, 3“, 45° 057 758.004 14 1x Delivery hose SK 65, 3“, 5,000 mm 057 886.002 15 6x Sponge rubber ball, ø 65 mm 000 246.000 16

additional accessories: 1x Lid for T-delivery pipe, 4.5“ 057 627.009 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

38 39

16

15

1,2,3

1,2,3 1,2,3

1,2,3

1,2,3 8,9,3 8,9,3 8,9,3 8,9,3

17

13

14

4

5

4

10 11 12

6

7

MM 2599/10 GB MM 2599/10 GB

Flexible delivery line for fine concrete, mortar, self levelling floor screed, NW 100 / 4.5“,85 bar, ≤ 16 mm grain size High pressure concrete spray line, SK 65 / SK 50, 3'', max 85 bar, ≤ 10 mm grain size


Complete Set, Part no.: 533 048Standard delivery line ≈ 60 m long, consisting of

Delivery line for fine concrete, mortar, self levelling floor screed, SK 100 / 4.5“, 85 bar, ≤ 16 mm grain size


Part Part no. Fig. 22x Clamp coupling SK 4.5“ 431 613 1 22x Seal DN 100 / 4.5“ 057 341.000 2 22x Spring cotter 018 878.004 3 2x Elbow pipe SK 100 / 90°, 4,5“ 421 329 4 1x T-delivery pipeSK 100 / 4.5“, 1000 mm 057 614.009 5 1x Pressure gauge SK 100 / 4.5“, 100 bar 521 430 6 18x Delivery hose SK 100 / 4.5“, 2850 mm 057 607.003 11 6x Sponge rubber ball, ø 100 mm 016 091.003 12

Additional accessories: 1x Lid for T-delivery pipe 057 627.009 1x Manual gate valve GVM 2/2 SK 100 / 4.5“ 222 362.005 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Delivery hose SK 100 / 4.5“, 5 m 057 609.001 11


Part Part no. Fig. 4x Clamp coupling SK 4.5“ 431 613 1 4x Seal DN 100, 4.5“ 057 341.000 2 30x Spring cotter 018 878.004 3 1x Elbow pipe SK 100, 90°, 4.5“ 421 329 4 1x T-delivery pipeSK 100, 4.5“, 1,000 mm 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 1x Reduction pipe SK 100, 4.5“- SK 65 / 3“, 1 m 224 269.009 7 16x Clamp coupling SK 3“ 417 798 8 16x Seal DN 65, 3“ 064 084.004 9 3x Delivery hose SK 65, 3“, 5,000 mm 057 886.002 10 1x Reduction pipe SK 65, 3“ - SK 50, 3“, 1,000 mm 058 670.000 11 4x Delivery hose SK 50, 3“, 5,000 mm 481 171 12 1x Transmission piece SK 50, 3“ auf 2“, IG 082 784.001 13 1x Concrete spraying nozzle with rubber nozzle 2“, AG 532 589 14 6x Sponge rubber ball, ø 60 mm 000 212.005 15 6x Sponge rubber ball, ø 80 mm 000 246.000 16 2x Air hose 3/4“, 20 m 416 016 17 1x Spare rubber nozzle 532 590

additional accessories: 1 x Lid for T-delivery pipe 057 627.009 1 x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 48x Clamp coupling SK 4.5“ 431 613 1 55x Seal DN 100, 4.5“ 057 341.000 2 55x Spring cotter 018 878.004 3 4x Elbow pipe SK 100 / 90°, 4.5“ 421 329 4 1x T-delivery pipeSK 100 / 4.5“, 1,000 mm 057 614.009 5 1x Pressure gauge SK 100, 4.5“, 100 bar 521 430 6 30x Delivery pipe SK 100 / 4.5“, 3,000 mm 056 863.000 7 4x Delivery pipe SK 100 / 4.5“, 2,000 mm 056 862.001 8 2x Delivery pipe SK 100 / 4.5“, 1,000 mm 056 861.002 9 4x Elbow pipe SK 100 / 4.5“, 45° 057 593.007 10 1x Delivery hose SK 100 / 4.5“, 2,850 mm 057 607.003 11 6x Sponge rubber ball, ø 100 mm 016 091.003 12

additional accessories: 1x Manual gate valve GVM 2/2, SK 100-4.5“ 222 362.005 1x Lid for T-delivery pipe, 4.5“ 057 627.009 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Pipe clamp for wall or floor 052 930.005 1x Delivery pipe 5,000 mm 057 609.001 11


As an alternative to individual SK couplings and seals, you have the option of using SKD couplings with halved seals already integrated:

Part Part No.SKD 4,5“ 494 868SKD 3“ 494 763

40 41

P 718TD

MM 2599/10 GB MM 2599/10 GB


Machine type trailer pump stationary pump trailer pump Pump 2-cyl. piston pump, hydraulically drivenTheor. delivery rate (piston side) 17.4 m3/h 17.4 m3/h 24 m3/hTheor. delivery pressure (piston side) 70 bar 70 bar 50 bar* Cylinder diameter 150 mm 150 mm 150 mm Diameter piston stroke 700 mm 700 mm 700 mmStrokes per minute (minimum) 25 25 36 Drive cylinder diameter 80 / 45 mm 80 / 45 mm 80 / 45 mmDrive motor 3-cyl. diesel engine Deutz F3M 2011, 34.5 kWHopper capacity 360 lChassis T-chassis, Knott skid frame with T-chassis Knott 2,500 kg, with brakes mountings for fork-lift 2.500 kg, with brakesWeight 2,450 kg 2,300 kg 2,450 kgLength 4,341, max. 4.503 mm 3,025 mm 4,503 mmWidth 1,600 mm 1,270 mm 1,600 mm Height 1,750 mm 1,559 mm 1,750 mm Filling height 1,180 mm 1,120 mm 1,180 mm Maximum grain size 32 mm 32 mm 32 mmDischarge connection SK 5.5“ SK 5.5“ SK 5.5“ Part no. 111 514.010 on request on request

Machine + high pressure cleaner +radio remote controlPart no. 111 514.030

Machine + high pressure cleanerPart no. 111 514.040

Technical data P 718 TD P 718 SD P 718TDS

The new P 718 offers all the advantages of its little sister the P 715 and is ideal for pumping fine concrete with a grain size of up to 32 mm in addition to traditional liquid screed applications.

P 718TD

3-cyl. diesel engine Deutz motor, complies with the current COM III exhaust emissions standard T-chassis, approved for road use Stable support feet for a reliable foothold Plastic engine hood and TARGA hoop Hopper with agitator and rubber collar Folding 30 mm safety grid screen with 12 volt vibrator safety shutoff for agitator Hopper with flap for emptying and cleaning Folding hopper attachment 2-cylinder piston pump with hard-chrome-plated delivery cylinders and a water box between the drive and delivery cylinders to flush the pistons and cool the piston rods It is possible to replace the pistons through the water box Hydraulic control of pump and S-valve. Infinitely variable pumping rate, manually adjustable Central lubrication manifold Lifting ring

Standard equipment:cleaning accessories, toolbox with tools, protective helmet (yellow), operating manual and spare parts list.

Part no. 111 514.010

P 718SD

Identical to P 718 TD, instead of chassis: skid frame with mountings for fork-lift

Part no. 111 584.010

P 718TDS

Identical to P 718 TD, but with rod-side drive for increased output at lower pressure

on request

Part Part no. Central lubrication system 524 883 Cable remote control, electric, 5 m 435 566 (pump on / off, reverse pumping, emergency off) Particle filter exhaust system on request Radio remote control with transmitter 438 062 and receiver (pump on / off, reverse pumping, emergency off) High-pressure cleaner, 140 bar – installation kit – 526 919 600 l/ h with spray gun and 8 m high-pressure hose Flushing water pump, 20 bar, 80 l/min on request – installation kit – Working light, 12 V, 50 Watt Halogen 462 956 End pipe with flap 436 849 Remote control cable, 10 m 246 780.003 Remote control cable, 20 m 246 781.002 Remote control cable, 50 m 246 782.001 Ball hitch 210 388.004 Special paint for hood (RAL colour) on request 13-pin to 7-pin adapter socket 437 679 7-pin to 13-pin adapter socket 248 012.009

* Theor. delivery pressure and rate, rod-side drive

P 718

Compact trailer fine concrete pump with S-valve for up to 32 mm grain

The P 718 is operated entirely from one side.a From here, you always have the material flow from the truck mixer in view.

Once the hood is open, all main-tenance and service areas can be accessed quickly and conveniently from here.

The large hopper need only to be folded away to the side for easy maintenance or cleaning. The agitator is already open and easily accessible in front of you.

www.mortarmachines.comwww.mortarmachines.comPiston pump Fine concrete pumps


4342MM 2599/10 GB MM 2599/10 GB

Suggested accessories for P 718www.mortarmachines.comwww.mortarmachines.com

Delivery line for fine concrete, mortar, self levelling floor screed, ID 125, 5.5“, 85 bar, ≤ 32 mm grain size Flexible delivery line for fine concrete, mortar, self levelling floor screed, ID 125, 5.5“, 85 bar, ≤ 32 mm grain size



For additional accessories, like manual distributors or manual gate valves, etc. see page 96 ff.

Part Part no. Fig. 60x Clamp coupling SK 5.5“ 417 249 1 60x Seal 5.5“ 055 559.001 2 60x Spring cotter 018 878.004 3 6x Elbow pipe SK 125, 5.5“ 90° r=275 HD 261 402.007 4 1x T-delivery pipe SK 125, 5.5“ 1,000 mm 057 615.008 5 1x Pressure gauge SK 125, 5.5“ 100 bar 521 448 6 2x Delivery pipe SK 125, 5.5“, 1000 mm 056 849.008 7 2x Delivery pipe SK 125, 5.5“, 2,000 mm 056 850.000 8 32x Delivery pipe SK 125, 5.5“, 3,000 mm 056 851.009 9 2x Elbow pipe SK 125, 5.5“, 45°, 057 596.004 10 2x Elbow pipe SK 125, 5.5“, 30°, 258 935.008 10 4x Delivery hose SK 125, 5.5“, 3,000 mm 433 497 11 6x Sponge rubber ball D150, medium 018 841.002 12 6x Sponge rubber ball D150, hard 223 673.007 12 Additional accessories: 1x Manual gate valve GVM 2/2 130 bar 413 087 1x Wash-out port lid SK 125, 5.5“ 057 619.004 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Support holder for end hose 054 371.002 1x Pipe clamp for wall or floor 051 038.005 13

Part Part no. Fig. 60x Clamp coupling SK 5.5“ 417 249 1 60x Seal 5.5“ 055 559.001 2 60x Spring cotter 018 878.004 3 4x Elbow pipe SK 125, 5.5“ 90° 261 402.007 4 1x T-delivery pipe SK 125, 5.5“, 1,000 mm 057 615.008 5 1x Pressure gauge SK 125, 5.5“, 100 bar 521 448 6 5x Delivery hose SK 125, 5.5“, 2,000 mm 027 643.000 11 18x Delivery hose SK 125, 5.5“, 5,000mm 057 612.001 11 6x Sponge rubber ball D150, medium 018 841.002 12 6 x Sponge rubber ball D150, hard 223 673.007 12 3 x End hose SK 125, 5.5“, 3,000 mm 233 649.005 13

Additional accessories: 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 1x Lid for T-delivery pipe, 5.5“ 057 628.008 1x Delivery hose SK 125, 5.5“ 3,000 mm 433 497 11 1x Delivery hose SK 125, 5.5“, 4,000 mm 089 983.009 11 1x Support holder for end hose 054 371.002 1x PM hose caddy, complete 482 464


4544MM 2599/10 GB MM 2599/10 GB

Delivery line for fine concrete, mortar, self levelling floor screed, ID 100 / 4.5“, 85 bar, ≤ 16 mm grain size




Flexible delivery line for fine concrete, mortar, self levelling floor screed, ID 100 / 4.5“, 85 bar, ≤ 16 mm grain size



For additional accessories, like manual distributors or manual gate valves, etc. see page 96 ff.

Part Part no. Fig. 6x Clamp coupling SK 5.5“ 417 249 1 6x Seal , 5.5“ 055 559.001 2 60x Spring cotter 018 878.004 3 2x Elbow pipe SK 5.5“ 90° 261 402.007 4 1x T-delivery pipeSK 125, 5.5“; 1,000 mm 057 615.008 5 1x Pressure gauge SK 125, 5.5“ 100bar 521 448 6 1x Reduction pipe SK 125, 5.5'', SK100, 4,5“ 057 604.006 7 1,000 mm 50x Clamp coupling SK 4.5“ 431 613 8 50x Seal DN 100, 4.5“ 057 341.000 9 30x Delivery pipe SK 100, 4.5“, 3,000 mm 056 863.000 10 4x Delivery pipe SK 100, 4.5“, 3,000 mm 056 862.001 11 2x Delivery pipe SK 100, 4.5“, 3,000 mm 056 861.002 12 4x Elbow pipe SK 100, 4.5“, 90° 421 329 13 4x Elbow pipe SK 100, 4.5“, 45° 057 593.007 13 1x End hose SK 100, 4,5“, 2,850 mm 057 607.003 14 6x Sponge rubber ball DN120, ø 100 mm 016 091.003 15

Additional accessories: 1x Lid for T-delivery pipe, 5.5“ 057 628.008 1x Pipe clamp for wall or floor 051 038.005 16 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 6x Clamp coupling SK 5.5“ 417 249 1 6x Seal 5.5“ 055 559.001 2 60x Spring cotter 018 878.004 3 2x Elbow pipe SK 125, 90°, 5.5“ 261 402.007 4 1x T-delivery pipe SK 125, 5.5“ 1000mm 057 615.008 5 1x Pressure gauge SK 125, 5.5“ 100bar 521 448 6 1x Reduction pipe SK 125, 5.5“, SK 100 / 4.5“ 057 604.006 7 1,000 mm 50x Clamp coupling SK 100, 4.5“ 431 613 8 50x Seal DN 100, 4.5“ 057 341.000 9 18x Delivery hose SK 100, 4.5“, 2,850mm 057 607.003 10 6x Sponge rubber ball DN 120, ø 100 mm 016 091.003 11

Additional accessories: 1x Lid for T-delivery pipe, 5.5“ 057 628.008 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Optional: 1x Delivery hose SK 100, 4.5“, 5,000mm 057 609.001 10

46

– – – – – – – – – –

– –

– – – – –

47

– – – – – –

– – – – – – – – – –

– – – – – – – – – – – – – –

– – – – – – – –

–

MM 2599/10 GB MM 2599/10 GB

No matter what you want: the right Putzmeister machine helps you to tackle most different operations in surface and under-ground engineering, and in the construction industry.

Note: Always use a machine-compatible mortar in combina-tion with machine technology. If you have any questions, please contact the material manufacturer or contact us directly.

Machines for mortars and plasters

Mixer pumpsMP 10 / MP 12 / MP 22 / MP 25

Pages 48-59

Conveying unitsFA 400 / FA 420 / FAT 400 / FAT 420

Pages 60-61

Worm pumpsSprayboy P12

Pages 62-63

S 5 / SP 5

Pages 66-75

Continuous mixerCM 528 – 20

Pages 76-77

Worm pumpsSP 11 Beliso series

Pages 78-83

Piston pumpsP 13

Pages 84-85

Gyps

um m

achi

ne p

laster

s

Gyps

um lim

e mac

hine p

laster

s

Lim

e m

ortar

Lim

e an

d ce

men

t mor

tar

Cem

ent m

ortar

Lim

e m

ortar

Lim

e an

d ce

men

t mor

tar

Cem

ent m

ortar

Ligh

tweig

ht p

laster

s

Insu

latin

g pl

aster

s

Dry mixed mortar (bag/ silo/ container goods) Plastic mortar/ Construction- Dispersion plasters site mixes

Machine- Ground coat plasters Mineral Special plasters Fine Ma- Re- SPCC- All wet mortars Indoor plaster Exterior plaster Ma- gypsum plasters bonding plasters sonry fractory- mortar (in the container (mix design 1:3) (mix design 1:3) sonry mortar mortar mortar or bucket) mortar

< 2mm < 4 mm

Bond

ing/

rein

forc

emen

t mor

tar

Spra

yed

rend

erin

g

Floa

ting

and

set

Roug

h co

at

Felt

and

floate

d pl

aster

s

Plas

ter fi

llers

Floa

ting

and

set

Bond

ing

mor

tar

Lim

e pl

aster

s

Lim

e gy

psum

plas

ters

Lim

e-ce

men

t plas

ters

Cem

ent p

laster

s

www.mortarmachines.comwww.mortarmachines.com Application overview – Plastering machines


48 49MM 2599/10 GB MM 2599/10 GB

Part Part no. Mixing spiral for lightweight plaster 508 078

Supplementary equipment MP 10 / MP 12

The smallest Putzmeister mixing pumps of all time. And although it's hard to believe, they both offer everything you have come to expect from a genuine Putzmeister mixing pump: continuous mixing, good output, dismantlability and a comprehensive range of fittings as standard.

Ideal machines for small companies, smaller jobs and situations where only a 230 V power supply is available.

MP 10

Small and powerful electric motor, detachable, with wedge closing device (MP 12) or toggle lock (MP 10) Compact unit with perfectly matched motor and frequency inverter Large hopper with hinged grille and bag opener Compressor with pressure cut-off Detachable mixing zone Pneumatic remote control Integrated water pump with flow and pressure regulation Compressor with pressure switch-off Easily accessible flow meter for modifying the water quantity

Standard equipment: 10 m mortar hose, 10 m air hose, spray gun V 25-40, operating manual and spare parts list

Part no. 111 594.010

MP 12

Identical to MP 10, with hinged bracket for optional compressor

Part no. 111 595.019


Drive motor 1.5 kW, 82-575 rpm 1.5 kW, 82-575 rpmPump type N13S N13SVoltage 230V 50 Hz + 60 Hz 230V 50 Hz + 60 Hz Theor. delivery rate* 0.5-16 l/min** 0.5-16 l/min** Delivery pressure max 30 bar max 30 bar Air compressor 230 V 50 Hz + 60 Hz, 180l/min 230 V 50 Hz + 60 Hz, 180l/minTank capacity 40 l 40 l Weight (approx.) 90 kg 90 kg Length 1,500 mm 1,500 mm Width 530 mm 620 mm Height 790 mm 1,020 mmFilling height 600 mm 900 mmMaximum grain size 4 mm 4 mmDischarge connection V 25-40 V 25-40 Part no. 111 594.010 111 595.019

Technical data MP 10 MP 12

* The delivery rate depends on the rotor/ stator and pump speed (rpm). Depending on the speed, the delivery rate may be higher or lower.

** Constant 16 l/min with mixing pump operation

The operating elements are located centrally and are well protected to the rear of the two mixing pumps (MP 12 shown here).

Here you can set the water rate conveniently and accurately.

Simply release the toggle locks of your MP 12 (MP 10 has wedge closures). You simply remove the motor and pump units in one.

The MP 10 / MP 12 can be used as a mixing pump or as a worm pump.

Mixer pumps MP 10, MP 12Fully-fledged mini-mixer pumps

MP 10 for use with site-made mixes

MP 12 for filling by hand / from a bag

Plastering machines Mixer pumpswww.mortarmachines.comwww.mortarmachines.com


50 51MM 2599/10 GB MM 2599/10 GB

Part Part no. Without air hose and compressor (reduced prize) 002 774.004 Remote control cable 60 m 269 447.006 with toggle switch Remote control cable 20 m 269 446.007 with toggle switch Water inlet nozzle 4.5 ø x 55 mm 400 728 Flow meter 40-400 l/h 407 200 (for D41⁄2 and D41⁄4) cpl., bypass Flow meter 300-1,100 l/h 205 945.009 Water connection piece for hose cleaning 207 936.003 Geka/ V 25-40 Water booster pump 212 383.007 230 V, 50 Hz, 2.4 m3/h Additional pressure increase pump, 429 706 230 V, 2.500l/ h, 2,5 bar Additional pressure increase pump 435 229 3 x 400 V / CEE 2.250 l/h Additional pressure increase pump NT61 422 097 without automatic switching, 3 x 400 V Standard mixing shaft MP 22 212 627.006 Supply cable with CEE plug 214 592.003 5 x 2,5 mm2, 16 Amp.

Supplementary equipment MP 22

Mixer pump MP 22The ”small“ mixer pump for refurbishers, painters and small teams

Plastering machines

The MP 22 is compact, light-weight and robustly mounted and is therefore the ideal machine when there is no need for a large machine. Nevertheless the MP 22 is a typical Putzmeister mixer pump. It can be dismantled into modules that can be carried and it handles all types of pre-blended dry mortar, and for easy transport it is unbelievably compact.

It is ideal for internal plasters (gypsum/ gypsum-lime plaster), external render (lime/ cement-lime and insulating plasters), self levelling floor screed, bonding mortar as well as reinforcement mortar.

MP 22

large hopper with bag opener Easily accessible flow meter for modifying the water quantity Conical mixing tube Possibility to connect an electric remote control Compressor with pressure switch-off An electric supply cable with CEE plug 5 x 2.5 mm2, 16 amp is recom-mended.

Standard equipment: 1 x mortar hose 10 m, 25 / 40 mm, air hose 10m, spray gun, cleaning tools, reduction piece V 35 / V25, operating instructions, standard tools and spare parts list

Part no. 111 479.009

MP 22 230 V

Same as MP 22, but as single phase 230 V / 50 and 60 Hz version, and additional pump test pressure device

Part no. 111 479.025


Pump type D6 Power D6-2 Theor. delivery rate* 25 l/min 16 l/min Delivery pressure 40 bar 20 bar Delivery distance** up to 40 m horiz., up to 15 m high up to 15 m horiz., up to 10 m high Air compressor 200 l/min 180 l/min 0.55 kW 0.52 kW + 60 HzDrive motor 400 V / 50 Hz / 5,5 kW / 389 UpM 230 V / 50 Hz + 60 Hz / 4 kW / 366 UpMTank capacity 50 l 50 l Weight (approx.) 160 kg 165 kg Length 1,200 mm 1,120 mm Width 660 mm 660 mm Height 1,276 mm 1,269 mmFilling height 1,084 mm 1,072 mmMaximum grain size 4 mm 3 mmDischarge connection M 35 M 35 Part no. 111 479.009 111 479.025

Technical data MP 22 MP 22 230 V

Mixer pumps


** The data is based on experience and is dependent on the materials used.

The MP 22 has a wide channel to the mixing zone. This means the dry material can flow through more easily.

The MP 22 can be used wherever bagged goods are used.

All connections and operating ele-ments are at the rear – outside the „contamination zone“.



52 53MM 2599/10 GB MM 2599/10 GB

Accessories for levelling compound

Suggested accessoriesfor MP 22

Accessories for plaster/ stucco (high performance 40 l/min)

Accessories for bonding mortar, reinforcement mortar, structural plaster (low performance 12 or 6 l/min)

Suggested accessories for mixer pump MP 22www.mortarmachines.comwww.mortarmachines.com




Part Part no. Fig. 5x Seal ID 25 207 764.000 1 2x Mortar hose ID 25, 10m 207 804.009 2 5x Sponge rubber ball ID 25 000 239.004 3 1x Electric remote control 269 446.007 4 with On/ Off switch 20 m 3x PM hose holder, made of leather 000 206.008

Optional accessories: 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004 2x Electric radio remote control 269 447.006 4 with On / Off switch 60 m

Part Part no. Fig. 1x D8-2 stator 436 746 6 1x D8-2 rotor 436 743 6 1x Spray gun – short, straight V 35 203 054.002 1 2x Mortar hose ID 35, kpl. 13,3 m lang 212 262.005 2 2x Air hose 1/2“, 20 m 209 174.009 3 5x Sponge rubber ball ID 35 001 665.004 4 10x Seal ID 35 213 725.004 5 3x PM hose holder, made of leather 000 206.008

Optional accessories: 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 1x Pump parts D4 1⁄2 (12 l/min) 1 – Rotor D4 1⁄2 214 402.009 – Stator D4 1⁄2 214 403.008 1x Discharge meter 40-400 l/min 208 025.007 2 1x Insertion nozzle ø 4,5 mm x 55 mm 400 728 3 2x Hose line ID 25-40 4 – Hose line ID 25-40, 10 m 207 804.009 1x Extension cable 20 m 211 506.005 6 5x Sponge rubber ball ID 25 000 239.004 8 5x Seal ID 25 207 764.000 9 1x Air hose 1/2“, 20 m 001 665.004 10 1x Large fine plaster spraying machine with 529 733 11 PM coupling and Geka air connection 3x PM hose holder, made of leather 000 206.008

Optional accessories: 1x Pump parts D4 1⁄4 (6 l/min) 1 – Rotor D4 1⁄4 214 572.007 – Stator D4 1⁄4 214 573.006 1x Adhesive gun DN 17 / M 25-40 with 408 422 5 shut-off valve and electrical connection for remote control 1x Spray gun ID 25 402 592 7 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

54 55MM 2599/10 GB MM 2599/10 GB

Mixer pumps MP 25 MIXIT + MP 25 FMP 60

Machine with large supply hopper for dry mixed mortar

Easy to disassemble, but difficult to outperform. The MP 25 is a true all-rounder. Suitable for all pumpable ready-mixed dry mortars, whether from a bag or from a silo, for example interior-use plaster (gypsum/ gypsum-lime plaster), external render (lime/ lime cement and insulating plaster), self levelling floor screed, cementitious adhesive and reinforcement mortar. Different pump parts and versions vary your mixing and pumping output of approximately 5-80 l/min.

MP 25 MIXIT

Powerful electric motor Large storage hopper Conical mixing tube Integrated water pump Compressor with pressure switch-off Compressed air remote control Can be dismantled into practically sized assemblies Easily accessible flow meter for modifying the water quantity

A supply cable with CEE plug 5 x 2.5 mm2, 32 A is recommended here.

Standard equipment: 1 x mortar hose 15 m, 25 / 40 mm, 1 x air hose 15 m, 1⁄2 ” Hose adapter V35 / V25, spray gun ID 25 / 40, mixing shaft, cleaning tools, operating instructions, standard tools and spare parts list

Part no. 111 417.168

MP 25 FMP 60

Version for processing liquid screed from a bag at high power without a compressor, without air fittings and control, with a special mixing spiral and a modified mixing pipe flange

Standard equipment: mixing shaft, Remote control cable 20m with toggle switch, cleaning tools, operating instructions and spare parts list

Part no. 111 417.268


Plastering machines

Part Part no. Filter hood with control cable, 212 324.008 probe, rectangular Water filter 5 m3/h, 3⁄4 ” GEKA 214 780.006 Insulating plaster hopper extension 212 325.007 Mixer shaft for insulating plaster 212 262.005 Mixer shaft for bonding mortar 214 571.008 Construction site electric supply cable with 062 921.004 CEE-plug, 32 Amp, 50 m 5 x 2.5 mm Water hose, GEKA, 210 789.001 coupling 3⁄4 ” NW, 40 m CEE coupling socket 014 184.006 Reduction NW 35 / NW 25 207 795.008 Water suction hose 509 540

Only for MP 25 FMP 60 version: Reduction R8 - D Pumpe 496 042 O-ring für reduction R8 - D pump 017 192.008


Pump type D6 Power R8 1.5 Theor. delivery rate* 25 l/min 80 l/min Delivery pressure 40 bar 25 bar Delivery distance** up to 40 m horizontally, 15 m high up to 40 m horizontally, 15 m highAir compressor 0.55 kW / 200 l/min –Drive pump 400 V / 50 Hz / 5.5 kW bei 392 rpm 400 V / 50 Hz / 5.5 kW bei 321 rpmDrive hopper 1.1 kW at 23 UpM 1.1 kW bei 23 UpMTank capacity 115 l 115 l Water pump 0.78 kW at 3.4 m3/h 0.78 kW at 3.4 m3/hWeight 240 kg 245 kg Length 1,324 mm 1,318 mm Width 728 mm 765 mmHeight 1,443 mm 1,453 mmFilling height 984 mm 984 mm Maximum grain size 4 mm 4 mm Discharge connection M 35 M 35Part no. 111 417.168 111 417.268

Technical data MP 25 MIXIT MP 25 FMP 60

Mixer pumps

The MP 25 MIXIT can be dismantled into manageable, portable assemblies in no time at all.

The large hopper and the low filling height makes it distinctively more convenient and makes your work easier.

Material container and mixing tube are separated from each other. You open the gate valve and the material flows into the mixing tube.


** The data is based on experience and is dependent on the materials used.



56 57MM 2599/10 GB MM 2599/10 GB

Accessories for preblended dry mortar (high performance 40 l/min)

Suggested accessoriesfor MP 25

Accessories for insulating plaster (high performance 40 l/min)

Accessories for cement, reinforcement mortar, structural plaster (low performance 12 or 6 l/min)

Suggested accessories for mixing pump MP 25

Accessories for self levelling floor screed processing with Dynamat additional mixer (performance up to 40 l/min)


Part Part no. Fig. 1x Pump parts D8-2 1 – Rotor D8-2 436 743 – Stator D8-2 436 746 1x Mixer shaft for insulating plaster MP 25 212 262.005 2 1x Spray gun with shut-off valve ID 35 209 174.009 3 2x Air hose 1/2“, 20 m 001 665.004 4 10x Seal ID 35 213 725.004 5 10x Sponge rubber ball ID 35 065 044.001 6 1x Insulating plaster attachment collar ID 25 212 325.007 7 1x Dynamat additional mixer with own 111 511.006 8 2.2 kW, 400 V drive motor and mixer speed of 632 rpm as well as 2 m hose ID 35 and connecting cable to mixing pumps 3x Mortar hose ID 35, cpl. 13.3 m 207 615.007 9 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 1x Pump parts D4 1⁄2 (12 l/min) 1 – Rotor D4 1⁄2 214 402.009 – Stator D4 1⁄2 214 403.008 1x Cementitious adhesive mixer shaft for MP 25 214 571.008 2 1x Discharge meter 40-400 l/min 208 025.007 3 1x Insertion nozzle ø 4.5 mm x 55 mm 400 728 4 2x Hose line ID 25-40 5 – Hose line ID 25-40, 10 m 207 804.009 1x Fine plaster spray gun large, with PM-coupling 529 733 8 and Geka Air hose connection 5x Sponge rubber ball ID 25 000 239.004 9 5x Seal ID 25 207 764.000 10 1x Air hose 1/2“, 20 m 001 665.004 11 3x PM hose holder, made of leather 000 206.008

Optional accessories: 1x Pump parts D4 1⁄4 (6 l/min) 1 – Rotor D4 1⁄4 214 572.007 – Stator D4 1⁄4 214 573.006

Part Part no. Fig. 1x Pump parts D8-2 1 – Rotor D8-2 436 743 – Stator D8-2 436 746 10x Seal ID 35 213 725.004 2 10x Sponge rubber ball ID 35 065 044.001 3 1x Dynamat additional mixer with 2.2 kW 111 511.006 4 drive motor and 632 rpm mixer speed to be integrated in mortar line and 2 m hose ID 35 1x Electric remote control with On/ Off switch 60 m 269 447.006 5 3x Mortar hose ID 35, cpl. 13.3 m 207 615.007 6 1x Discharge meter 160-1,600 l/h 208 026.006 7


Part Part no. Fig. 1x Discharge meter as bypass 407 200 3 (40-400 l/min) for D4 1⁄2 and D4 1⁄4 1x Adhesive gun DN 17 / M 25-40 with 408 422 6 shut-off valve and electrical connection for remote control 1x Extension cable 20 m 211 506.005 7 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Part no. Fig. 1x Pump parts D8-2 1 – Rotor D8-2 436 743 – Stator D8-2 436 746 1x Universal mixer shaft MP 25 211 773.003 2 1x Spray gun – short, straight V 35 203 054.002 3 2x Mortar hose ID 35, 13.3 m 207 615.007 4 2x Air hose 1/2“, 20 m 001 665.004 5 10x Sponge rubber ball ID 35 065 044.001 6 10x Seal ID 35 213 725.004 7 3x PM hose holder, made of leather 000 206.008






58 59MM 2599/10 GB MM 2599/10 GB

Accessories for self levelling floor screed; with MP 25 FMP 60 only!

Suggested accessories for mixing pump MP 25www.mortarmachines.comwww.mortarmachines.com

Accessories for preblended dry mortar from silo

Accessories for self levelling floor screed with Uni mixer (performance up to 40 l/min)

Accessories for preblended dry mortar

Part Part no. Fig. 1x Pump parts R8 1.5 1 –Rotor R8 1.5 500 850 – Stator R8 1.5 501 062 10x Seal ID 35 213 725.004 2 10x Sponge rubber ball ID 35 065 044.001 3 1x Electric remote control, 4 with ON / OFF switch 60 m long 269 447.006 3x Mortar hose 35, cpl. 13.3 m 207 615.007 5 1x Mixer shaft 503 353 6


Part Part no. Fig. 2x Mortar hose ID 35, cpl. 13.3 m 207 615.007 1 2x Air hose 1/2", 20 m 001 665.004 2 10x Seal ID 35 213 725.004 3 10x Sponge rubber ball ID 35 065 044.001 4 1x Feed hood with control cable and 212 324.008 6 probe, rectangular 3x PM hose holder, made of leather 000 206.008 1x Spray gun – short, straight V 35 203 054.002 5


Part Part no. Fig. 1x Uni mixer 400 566 1 cpl. with tie bolt + union nuts Pump parts: – 1 x Stator D8-2 436 746 2 – 1 x Rotor D8-2 with pin 436 744 1x Discharge pressure gauge 472 506 3 1x Electric remote control, 4 with ON/ OFF switch, 60 m long 269 447.006 3x Mortar hose ID 35, 13.3 m 207 615.007 5 1x Discharge meter 160-1,600 l/h 208 026.006 6 10x Sponge rubber ball ID 35 065 044.001 7 10x Seal ID 35 213 725.004 8 4x Spacer plate 207 770.007 9 8x Hexagon head bolt M 10 x 60 032 146.000


Part Part no. Fig. 2x Mortar hose ID 25 - 40, 10 m 207 804.009 1 1x Spray gun ID 25 402 592 2 5x Seal ID 25 207 764.000 3 5x Sponge rubber ball ID 35 000 239.004 4 3x PM hose holder, made of leather 000 206.008






For further details see pages 60 / 61.

60 61MM 2599/10 GB MM 2599/10 GB

Conveying units FA 400, FAT 400, FA 420, FAT 420The special dry conveying units for silo operation

The ideal complement to the MP 22, MP 25 and other mixer pumps. The economic dry conveying unit. It is optimally tuned to the performance of the mixer pumps that are used everyday. It transports pneumatically dry plasters or similar materials from every standard vessel, silo or container – fully automatically into the plastering machines.

FA 400

Pneumatic conveying system without silo ventilation Delivery vessel 65 l, delivery rate up to 3.2 t/ h Control cabinet with 3p probe incl. automatic phase detector

A supply cable with CEE plug 5 x 4 mm2, 32 A is recommended here.

Standard accessories: 1 coupl. socket 5p 32 A, 1 air hose, 7 m, 2xBC sickle spanner.

Part no. 111 446.003

FAT 400

Same as FA 400, but as stationary version without chassis and silo ventilation.

Part no. 111 447.002

Part Fig. Part no. Filter hood, round, cpl. with rotary 1 212 324.008 wing probe, 42 V compact filter for MP 25 Delivery hose PVC DN 38 x 12.5 m 2 212 263.004 Delivery hose, PVC DN 38 x 25 m 2 212 264.003 Pneumatic delivery hose, rubber, 486 928 DN 38 x 12.5 m Pneumatic delivery hose, rubber, 486 929 DN 38 x 25 m Exterior vibrator, 230 / 400 V, 50 Hz, 160 Watt 3 073 374.006 with 5 m cable, CEE plug, 16 A, 5-pole Control cable 50 m for probe 42 V 3p 4 212 342.006 Control cable 20 m for probe 42 V 3p 4 212 341.007 Sack-filling hopper 80 l 013 912.004 Sickle spanner 062 619.002

Filter hoods for other mixer pumps are supplied adapted to the PMM conveying system.


Conveying units

FA 420

Pneumatic conveying system without silo ventilation (retrofit part) Delivery vessel 65 l, delivery rate approx. 3,6 t/h Control cabinet with probe 42 V/ 3 pin, incl. automatic phase detector and pressure monitor control

A supply cable with CEE plug 5 x 4 mm, 32 A is recommended here.

Standard equipment:1 air hose 5 m, size 1“, 2 hose sickle spanners BxC.

Part no. 111 446.016

FAT 420

Same as FA 420, but as stationary version without chassis and silo aspiration.

Part no. 111 447.015


Silo connection DN 250 LK 300 mm, with quick-action couplingsChassis 450 kg, F 80, stationary 450 kg, F 80, stationary brakeless brakelessDrive motor 400 V, 25 A, 32 A plug, 400 V, 25 A, 32 A plug, semi automatic, phase recognition semi automatic, phase recognitionCompressor 5.5 kW S1, 1,450 rpm, 96 m3/h, 7.5 kW, 1,400 rpm, 129 m3/h, 2.8 bar, oil-lubricated 2.5 bar, dry-running compressor, air cooledAir fittings 1”, with pressure monitoring, prepared 1 ¼”, with pressure monitoring, prepared for connection silo ventilation for connection silo ventilation Probe connection 3p, 42 VAC, 16 A, rotary wing or capacitive systemHose connection Light alloy coupling, system Storz, size C (LM C)Delivery vessel 65 l, 59 kg, 945 mm 65 l, 59 kg, 945 mm 65 l, 59 kg, 945 mm 65 l, 59 kg, 945 mmTheor. delivery rate* e. g. 3.2 t/h, 50 m, density 1.2 kg/dm3 e. g. 3.6 t/h, 50 m, density 1.2 kg/dm3

Delivery distance* 150 m 150 m 150 m 150 mWeight 340 kg 137 kg 410 kg 180 kgLength 2.260 mm 1,060 mm 2,330 mm 1,050 mmWidth 1,420 mm 460 mm 1,325 mm 560 mmHeight 1,115 mm 560 mm 1,270 mm 560 mm Part no. 111 446.003 111 447.002 111 446.016 111 447.015

Technical data FA 400 FAT 400 FA 420 FAT 420

* depends on the material used and configuration of the hoses

The lightweight, manoeuvrable delivery container on the conveying system with actuator drive.

The FA 420 offers ample space under the hood for the delivery tank, an air injection hood and other accessories.

The conveying system can be opera-ted fully automatically via the control cabinet.

Conveying units www.mortarmachines.comwww.mortarmachines.com

Alternative: Stationary version

62 63MM 2599/10 GB MM 2599/10 GB

Pump type D5 short D4 redTheor. delivery rate* 6 +12 l/min 4.5 l/minDelivery pressure 25 bar 25 barDelivery distance** up to 30 m horizontally, 15 m high up to 20 m horizontally, 5 m highDrive motor 400 V / 50 Hz + 60 Hz, 16 A, 5p, 6h, CEE plug 230 V / 50 Hz + 60 Hz, 25 A, 3p, CEE plugDrive pump 1.4 kW at 94 rpm / 1.8 kW at 188 rpm 1.7 kW at 96 rpmVessel content 50 l 50 lWeight 125 kg 128 kgLength 714 mm 714 mmWidth 696 mm 696 mm Height 1,437 mm 1,437 mm Filling height 939 mm 939 mm Maximum grain size 4 mm 3 mm Discharge connection M 35 M 35Part no. 111 469.060 111 469.020

Technical data P 12 P 12 230 V


* The delivery rate depends on the rotor/ stator and pump speed (rpm). Depending on the speed, the delivery rate may be higher or lower.** The data is based on experience and is dependent on the materials used.

Discharge connection with pressure gauge for connection of the mortar hoses.

In the central control cabinet, the electrical system is easily accessible at all times – which makes mainte-nance work easier.

The large Sprayboy hopper, in which material is mixed before pumping.

Sprayboy P 12The flexible mixer and pump unit

Worm pumps

The small mortar pump, ideal mixing, pumping and spraying cemetitious adhesive, thin skim coat, fire-protection mortar, etc. from a hopper. Just the right machine for those working with building protective agents or stucco, carrying out renovation and repair work.

Suitable for: e.g. anti-drumming compounds, levelling compounds, refractory mortar, sealing compounds, joint and casing mortar, paint com pounds, priming coats, bonding mortars, refurbishing mortar, fillers, filling mortars, etc.

Sprayboy P 12 (P 12 230 V)

Electric worm pump drive large hopper Two-stage speed transfer

We recommend an inlet cable with CEE plug 5 x 2.5 mm2, 16 Amp. (input 3 x 2.5 mm2, 230 V plug). For plastering, a compressor (> 200 l/min) is required which must be supplied at the construction site. For texturing spray work, a compressor with at least 600 l/min air performance is required.

Part Part no. Extension for remote control cable, 20 m (binder) 211 506.005 Pneumatic remote control cpl. (binder) 212 425.004 Compressor HANDY, 250 l/min, 000 235.008 400 V / 50 Hz 3-phase Compressor HANDY, 250 l/min, 000 215.002 230 V / 50 Hz 1-phase Compressor V-MEKO 400, 360 l/min, 205 767.009 400 V / 50 Hz 3-phase For all MEKO compressors, you require: Geka coupling 1⁄4” 207 969.009 Supply cable with CEE plug 214 592.003 5 x 2.5 mm2, 16 Amp. Supply cable with shock proof plug 230 V 212 960.006 3 x 2.5 mm2



Standard equipment: Electric remote control cable 21 m, reduction connecting piece V 35 / V 25-40, operating manual, standard tools

Part no. 111 469.060 (P 12)Part no. 111 469.020 (P 12 230 V)



64 65MM 2599/10 GB MM 2599/10 GB

Accessories for filling between frame connectors and walls with fire-retardant mortar Accessories for filling between frame connectors and walls with fire-retardant mortar

Suggested accessories for Sprayboy P 12www.mortarmachines.comwww.mortarmachines.com

Accessories for finishing works Accessories for anchor filling



Suggested accessoriesfor Sprayboy P 12



Part Part no. Fig. 2x Mortar hose ID 25, 10 m 207 804.009 1 1x Frame connector filling pipe 30 cm M 25 - 40 408 373 2 3x Sealing ID 25 207 764.000 3 3x Sponge rubber ball ID 25 000 239.004 4 1x Electric remote control, 269 446.007 5 with ON/ OFF switch, 20 m 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 1x Mortar hose ID 25, 10 m 207 804.009 1 3x Seal ID 25 207 764.000 2 1x Frame connector filling gun with remote control 214 236.000 3 1x Extension for remote control cable, 20 m 211 506.005 4 3x Sponge rubber ball ID 25 000 239.004 5 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 2x Mortar hose ID 25, 10 m 207 804.009 1 1x Air hose 1⁄2 “, 20 m 001 665.004 2 1x Fine plaster spray gun, long 529 733 3 3x Sponge rubber ball ID 25 000 239.004 4 3x Seal ID 25 207 764.000 5 1x Compressor V-Meko with fuse 400 168 7 1x Geka-coupling 1⁄4 “ 207 969.009 8 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 1x Reduction V35 / V25-40 207 795.008 1 3x Seal ID 25 207 764.000 2 1x Pressure control device 2-32 bar 523 102 3 2x Mortar hose ID 25-40 10m 207 804.009 4 1x PM coupling M 25-40 / RI 1' 211 597.001 5 1x Pressure gauge DN 25-40 208 745.002 3x Sponge rubber ball ID 25 000 239.004 6 3x PM hose holder, made of leather 000 206.008


66 67MM 2599/10 GB MM 2599/10 GB

Worm pump 1L6 Theor. delivery rate* 4-25 l/min Delivery pressure approx. 15 bar Delivery distance** up to 40 m horizontally, up to 15 m high Drive motor 4 kW electric motor, 230 V, 50 Hz Drive motor 16 ampere-fuse, shock-proof plug Air compressor 0.52 kW, 230 V, 180 l/min, 3.5 bar Weight 190 kg Length 2,255 mm Width 675 mm Height 765 mm Hopper size 100 l Maximum grain size 6 mm Discharge connection M 50 Part no. 111 475.003

Technical data SP 5

* The delivery rate depends on the rotor/ stator and pump speed (rpm). Depending on the speed, the delivery rate may be higher or lower.** The data is based on experience and is dependent on the materials used.

The electric motor and compressor are clearly laid out and easily accessible. The compressor can be easily taken from the machineif required.

The 1L6 worm pump with pressure gauge and pressure connection.

Operation is easy. Everything is well laid out and easy to reach.

Part Part no. Reduction piece V 35-V 25 / 40 207 795.008 Remote control cable 20 m with toggle switch 269 446.007 Safety cut-out with 407 043 emergency shut-down key Construction site supply with 212 960.006 230 V earthed connector, 3 x 2.5 mm2, 20 m Adapter V50-M35 213 217.004 Vibrating screen, compl. for refitting 404 679 (ID 10 mm + vibrator + switch)


Worm pump SP 5The ”large” 230 V- universal pump with compressor

Worm pumps

The universal fine plastering machine with 230 V single phase drive is the same as the S 5 with regarding hopper volume. The 230 V drive motor allows it to be used everywhere where a 400 V connection is not available. The integrated compressor makes the SP 5 a complete plaste-ring machine.

The SP 5 processes almost all types of mortar, such as renovation plaster, dispersion plaster, injection, adhesive and reinforcing mortars with up to6 mm granulation.

A maintenance-free frequency inverter allows completely wear-free adjustment of the speed.

SP 5

Frequency inverter from 15-100 Hz to adjust the pump speed to 25-165 rpm. Possibility of connecting pneumatic and cable remote control. Worm pump easy to tighten due to standard series pump parts 1L6 with clip Compressor for spray and control air, 3.5 bar Compressor shutoff.

Caution: Only use machine with frequency inverter via AC/DCsensitive FI and with 2.5 mm2 cable diameters.

Standard equipment:pressure gauge at pressure outlet, cable remote control and compressed air remote control pump ON/ OFF, extension cable 20 m, 16 A 3-phase, 15 m air hose 1⁄2 ground coat spray gun V 35, operating instructions, reduction piece V 50 - M 35, emergency push button, spare parts list, standard tools and cleaning accessories.

Part no. 111 475.003

Worm pump SP 5 with optional vibrating screen shown

www.mortarmachines.comwww.mortarmachines.com Mortar spraying systems


68 69MM 2599/10 GB MM 2599/10 GB

Suggested accessoriesfor SP 5

Accessories for joint filling works

Accessories for cement, reinforcement mortar, structural plaster

www.mortarmachines.comwww.mortarmachines.com Suggested accessories for SP 5

Accessories for job site mixes

Accessories for Monocouche (Monocapa)





Part Fig. Part no. 1x Mortar hose ID 35 mm, V 50, M 35 13.3 m 1 207 616.006 1x Mortar hose ID 35 mm, V 35, M 35 13.3 m 2 207 615.007 1x Mortar hose ID 25 mm, V 35, V 25-40 5 m 3 207 808.005 5x Seal ID 35 4 213 725.004 5x Sponge rubber ball ID 35 6 065 044.001 1x joint device D10 ID 25 / 40 7 415 689 5x Seal ID 25 8 207 764.000 5x Seal ID 50 9 213 266.000 1x PM hose holder, made of leather 000 206.008


Part Fig. Part no. 1x Reduction piece V 50 - M 35 1 213 217.004 1x Mortar hose ID 25, V 35, V 25 10 m 4 207 809.004 1x Mortar hose ID 35, V 35, V 35 13.3 m 3 207 615.007 10x Seal ID 25 5 207 764.000 5x Sponge rubber ball ID 25 9 000 239.004 1x Air hose 1/2“, 20 m 10 001 665.004 1x Fine plaster spray gun , large, with PM coupling 11 529 733 3x PM hose holder, made of leather 000 206.008 10x Seal ID 35 12 213 725.004

Optional accessories: 1x Adhesive gun DN 17 / M 25-40 shut-off valve 6 408 422 and electrical connection for remote control 1x Extension cable 30 m 7 211 507.004 1x Spray gun ID 25 8 402 592 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

Part Fig. Part no. 1x Mortar hose ID 35 mm, V 50, M 35 13.3 m 1 207 616.006 1x Mortar hose ID 35 mm, V 35, M 35 13.3 m 2 207 615.007 1x Mortar hose ID 25 mm, V 35, V 25-40 5m 3 207 808.005 1x Air hose Geka 1/2"; 40 m 4 214 734.007 2x Sponge rubber ball ID 35 5 065 044.001 1x Spray gun ID 25-40, short 6 408 237 1x Rubber fine plaster nozzle 8 mm 214 751.006 1x Rubber fine plaster nozzle 10 mm 214 752.005 1x Rubber fine plaster nozzle 12 mm 214 753.004 1x Rubber fine plaster nozzle 14 mm 214 754.003 1x Rubber fine plaster nozzle 16 mm 214 755.002 1x Elastic mortar nozzle D18 001 329.007 1x PM hose holder, made of leather 000 206.008

Part Fig. Part no. 1x Mortar hose ID 35 mm, V 50, M 35 13.3 m 1 207 616.006 1x Mortar hose ID 35 mm, V 35, M 35 13.3 m 2 207 615.007 5x Seal ID 50 3 213 266.000 5x Sponge rubber ball ID 35 4 065 044.001 1x Spray gun V 35, short 5 001 306.004 5x Seal ID 35 6 213 725.004 1x Air hose Geka 1/2"; 40 m 7 214 734.007 3x PM hose holder, made of leather 000 206.008

Optional accessories: 1x Spray gun V 35 8 203 054.002 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

70 71MM 2599/10 GB MM 2599/10 GB


Part Part no. Pan mixer TM 100 111 353.002 Compressor HANDY, 250 l/min, 000 235.008 400 V / 50 Hz 3-phase Compressor V-MEKO 400, 360 l/min, 205 767.009 400 V / 50 Hz 3-phase and Geka coupling 1⁄4” 207 969.009 Compressor 590 l/min, 10 bar, 213 264.002 20 l air accumulator, 3 kW, 400 V, 50 Hz Pneumatic remote control cpl. 465 951 Silo connection D 245 – flexible – for CM 072 241.004 Chassis F 80, 750 kg, incl. certified inspection 208 732.006 Remote control extension cable, 20 m 470 037 Vibrating screen MW 10, 400 V, 50 Hz 208 322.001 Additional part number for pump parts D5 201 073.001 – conversion kit – infinitely adjustable 3-19 l/min Additional part number for pump parts 2L88, 204 402.006 infinitely adjustable 9.5-54 l/min Cleaning connection M35 / GEKA 070 692.008 Fill-level sensor 42 V for CM 204 572.004 Reducer coupling V 35-V25-40 207 795.008 Filter hood with sensor for CM 928 213 401.001 Pressure check gauge DN 25-40 208 745.002 CM 928 for attachment to S 5 438 789 Supply cable with CEE plug, 32 Amp. 062 921.004


Worm pumps www.mortarmachines.comwww.mortarmachines.com

Special feature basic version basic version with continous mixer with pan mixer basic version Worm pump 2L6 2L6 maintenance free 2L6 2L6 2L74Theor. delivery rate* 7-40 l/min 7-40 l/min 7-40 l/min 7-40 l/min 90 l/minDelivery pressure 25 bar 25 bar 25 bar 25 bar 25 barDelivery distance** up to 60 m up to 60 m up to 60 m up to 60 m up to 60 mDelivery height** up to 40 m up to 40 m up to 40 m up to 40 m up to 40 mDrive motor 5.5 kW, 400 V / 50 Hz 5.5 kW, 400 V / 50 Hz 5.5 kW, 400 V / 50 Hz 5.5 kW, 400 V / 50 Hz 7.5 kW, 400 V / 50 HzDrive mixer – – 5.5 kW 2.2 kW –Hopper volume 100 l 100 l 100 l 100 l 130 lLength 2,290 mm 2,290 mm 2,840 mm 2,290 mm 2,610 mmWidth 680 mm 680 mm 680 mm 680 mm 680 mmHeight 650 mm 650 mm 1.200 mm 1.150 mm 650 mmWeight 190 kg 190 kg 360 kg 400 kg 260 kgDischarge connection 6 mm 6 mm 6 mm 6 mm 10 mm Maximum grain size M 35 M 50 M 35 M 35 M 50Part no. 111 452.010 111 452.230 111 452.020 111 452.030 111 452.090

Technical data S 5 EV S 5 EV S 5 EV/CM S 5 EV/TM S 5 EF

The S 5 EV/TM with additional pan mixer is used wherever materials have to be mixed intensively.

* The delivery rate depends on the rotor/ stator and the pump speed (rpm). Depending on the speed, the delivery rate may be higher or lower.** The data is based on experience and is dependent on the materials used.

The S 5 EVCM with additional continous mixer CM 928 for premixed dry mortar.

The powerful S 5 EF for self levelling floor-screed.

The universal worm pump for dry mix and wet mortar from bag or silo. The S 5 has a modular design. It is based on a powerful worm pump with a pumping rate of 40 l/min. The TM version is fitted with a pan mixer for the best mixing quality, the CM version has a continuous mixer for dry-mix mortar.

Suitable for: ground coat plasters and insulating plasters, rough coat and textured plas ters, trowel plaster, adhesive bonded joint, masonry mor tar, refractory mortar, sealing suspensions, injection mortar, filling and ancho-ring mortar, dispersion plaster, fiber mortar, fibreglass concrete, bonding mortar, self levelling floor screed – infinitely variable according to material from approx. 7 l/min to 40 l/min (floor screed up to 90 l/min with 2L74).

S 5 EV

Powerful electric vario drive large hopper Infinitely variable pumping rate

Recommended is a power supply cable with CEE plug 5 x 4 mm2, 32 Amp. If pumpable wet mortar is mainly pumped and sprayed, a compressor > 200 l/min must be available on site for the spraying work. For texturing spray work, a compressor with at least 600 l/min air output is required.

Standard equipment:Set of wheels with pneumatic tyres, electric remote control cable 20 m, operating manual, standard tools.

Part no. 111 452.010

S 5 EV with plugged cardan shaft

Design and equipment identical to S 5 EV, but the new version has a plugged cardan shaft for the quick replacement of worm parts without a tool. A worm pump 2L54 for delivery rates of up to 55 l/min and a maxi-mum of 10 mm particle size can be installed.

Part no. 111 452.230

S 5 EV/CM *

Equipped as the S 5 EV, but with a continuous mixer CM 928/ 040-A01 with a mixing output of 40 l/min and 5.5 kW electric drive. Suitable for dry-mix mortar from the bag or from the silo.

Standard equipment: Same as S 5 EV but with control unit for CM mixer and fill-level sensor cpl. 42 V.

Part no. 111 452.020

S 5 EV/TM *

Equipped as the S 5 EV, but with a pan mixer TM 100 with a mixing volume of 80 l and 2.2 kW electric drive. Suitable for multi component mortar or with effectively longer requested mixing time.

Standard equipment: As version S 5 EV but wheel kit with inflatable rubber tyres.

Part no. 111 452.030

S 5 EF

Worm pump with powerful constant drive for larger quantities of material, particularly suitable for self levelling floor screed. Fitted with vibrating screen and vibrator.

Standard equipment: Same as version S 5 EV.

Part no. 111 452.090

* Versions are also available with plugged cardan shaft.


Worm pump S 5Universal worm pump


72 73

1

1

MM 2599/10 GB MM 2599/10 GB

Suggested accessoriesfor S 5

Accessories for job site mixes

Accessories for dry mortar (for cement plaster, fire proofing, EIFS)

Accessories for fine plaster (< 4 mm grain size)

www.mortarmachines.comwww.mortarmachines.com Suggested accessories for S 5

Accessories for anchor filling





Part Part no. Fig. 1x Pneumatic remote control 465 951 1 3x Mortar hose ID 35, 13.3 mm 207 615.007 2 1x Spray gun ID 35 001 306.004 3 2x Air hose, 20 m 001 665.004 4 1x Nozzle ø 16 mm 521 643 5 10x Seal ID 35 213 725.004 6 10x Sponge rubber ball ID 35 065 044.001 7 1x Geka coupling ¼“ 207 969.009 8

Part Part no. Fig. 1x fine plaster spray gun ID 25 529 733 1 5x Seal ID 25 207 764.000 2 1x Reduction ring V 35 - V 25-40 207 795.008 3 1x Adapter Geka / Ewo 402 489 4 1x Pneumatic remote control 465 951 5 2x Mortar hose ID 25, 10 m 207 804.009 6 1x Air hose ½“, 20 m 001 665.004 7 1x Cardan shaft D4 202 342.003 10 1x D6 Power rotor 443 740 11 1x D6 Power stator 206 345.006 12

Part Part no. Fig. 1x Pneumatic remote control 465 951 1 2x Mortar hose 35, 13.3 m 207 615.007 2 1x Mortar hose ID 35 207 808.005 3 V 35 - V 25 - 40, 5 m 2x Air hose ½“, 15 m 212 333.002 4 1x fine plaster spray gun ID 25 408 237 5 1x Nozzle ø 12 mm 521 641 6 1x Nozzle ø 14 mm 521 642 7 5x Seal ID 35 213 725.004 8 3x Seal ID 25 207 764.000 9

Part Part no. Fig. 1x Reduction V 35 / V 25-40 207 795.008 1 1x Pressure control device 2-32 bar 523 101 2 2x Mortar hose ID 25-40, 10 m 207 804.009 3 5x Seal ID 25 207 764.000 4 1x PM coupling M 25-40 / RI 1' 211 597.001 5 1x Pressure gauge DN 25-40 208 745.002


Part Part no. Fig. 1x Compressor V-Meko with fuse 400 168 9 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 5x Sponge rubber ball ID 35 065 044.001 10 3x Sponge rubber ball ID 25 000 239.004 11 1x Geka coupling ¼“ 207 969.009 12 1x Compressor V-Meko with fuse 400 168 13 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 2x Connecting rod, 325 mm 011 145.006 13 3x Sponge rubber ball ID 25 000 239.004 14 1x Strocomp 864 111 593.011 15 3x PM hose holder, made of leather 000 206.008


74 75MM 2599/10 GB MM 2599/10 GB

Conversion from S 5 EV 2L6 to D4, D4½, D4¼, D5 short, D6, D8-2++ with the following parts: Part Part no. 1x Cardan shaft (spiral) 202 342.003 or Cardan shaft (paddle) 206 185.004 2x Tie bolt 011 145.006 (l=325 mm, M 20)You can find rotors / stators on page 102 ff.

Conversion from S 5 EV 2L6 to D5 with the following parts: Part Part no. 1x Cardan shaft (spiral) 202 342.003 or Cardan shaft (paddle) 206 185.004 1x D5 Rotor 070 351.006 1x D5 Stator 070 352.005 1x Clamp complt. 206 848.008 2x Tie bolt 201 076.008 (l=410 mm, M 20)

Conversion from S 5 EV 2L6 to 1L6 with the following parts: Part Part no. 1x Cardan shaft (spiral) 202 342.003 1x 1L6 Rotor 207 136.007 1x 1L6 Stator 214 536.001 1x Clamp complt. 422 747 2x Tie bolt 011 145.006 (l=300 mm, M 20)

Conversion for existing S5 (Part no.: 111 452.010, 111 452.020, 111 452.030) to Version with plugged cardan shaft and rotor / stator 2L54: Part Part no. 1x Cardan shaft 455 703 1x Cardan flange 205 085.008 1x Drive shaft 204 980.007 1x Rotor 2L54 211 739.005 1x Stator 2L54 523 235 3x Hexagon nut M 12 034 107.005 3x Hexagon head bolt M 12 x 35 032 378.001 3x Hexagon head bolt M 12 x 45 032 162.000 3x Hexagon head bolt M 12 x 95 032 172.003 1x Flexible disk 010 103.007 1x Safety disk 036 507.001 1x ID 50 pressure connection 424 263 1x PM coupling M 50 / IG 2" 211 600.008

www.mortarmachines.comwww.mortarmachines.com Suggested accessories for S 5

Accessories for concrete renovation

Accessories for spraying GRC (glass fibre reinforced concrete) Modification of the pump type 2L6 of the S 5 to other pump types

Accessories for self levelling floor screed; with S5EF only!




Part Part no. Fig. 1x Control panel 207 223.004 1 1x GRC spray gun 070 436.002 2 1x Hose connection cpl. 209 347.001 3 1x Mortar hose ID 25, V 35 / V 25 - 40, 10 m 207 809.004 4 1x Cardan shaft (spiral) 202 342.003 5 1x Rotor D 8-2 436 743 6 1x Stator D 8-2 436 746 7 3x Seal ID 35 213 725.004 8 3x Seal ID 25 207 764.000 9 3x Sponge rubber ball ID 25 000 239.004 10 2x Tie bolt 011 145.006 11


Part Part no. Fig. 1x Pneumatic remote control 465 951 1 3x Mortat hose ID 35, 13.3 m 207 615.007 2 1x Refurbishing spray gun 207 283.002 3 1x Coupling V 35 203 135.002 4 2x Air hose, 20 m 001 665.004 5 5x Seal ID 35 213 725.004 6 5x Sponge rubber ball ID 35 065 044.001 7 1x Nozzle, ø 15 mm 207 286.009 8 3x PM hose holder, made of leather 000 206.008


In addition, a compressor with an air volume of 1,500 l/min is required.

Part Part no. Fig. 3x Delivery hose ID 50, V 50, M 50 13.3 m 501 914 1 5x Sponge rubber ball ID 50 000 212.005 2 5x Sealing ring ID 50 213 266.000 3


76 77MM 2599/10 GB MM 2599/10 GB

CM 528–20The “small one” for bag material

Drive 2.2 kW / 280 rpm 2.2 kW / 400 V 230 V / 50 Hz / 14 A 3 phases / 10 AWater fittings R 1/2” R 1/2”Water flow press. > 2.5 bar > 2.5 barHopper 70 l 70 lMixing tube 650 mm 650 mmMachine plug shock-proof 16 A, CEE 16 A, 3p blue 5000 LMixer perf. 25 l/min 25 l/minLength 1,700 mm 1,700 mmWidth 700 mm 700 mmHeight 1,000 mm 1,000 mmComplete weight 90 kg 95 kgMax. grain size 3 mm 3 mmPart no. 111 476.002 111 476.015

The compact, lightweight, mobile continuous mixer for mixing ready-mix dry mortar.

The CM 528 can process almost all pumpable machine plasters, wall pla-sters, finishing plasters and even masonry mortar with a maximum grain size of 3 mm and represents a better, more cost-effective alternative to the manual agitator.

CM 528–20

continuous mixer for bag material Driven by electric motor 2.2 kW, 230 V or 400 V Max. mixing capacity 25 l/min 70 litre sack filling hopper

Part Part no. Discharge meter retrofit kit 422 958 Supply cable, 3 x 2.5 mm2, with shock proof plug 212 960.006 Supply cable, with CEE-plug, 5 x 2.5 mm2, 16 A. 214 592.003

Supplementary equipment CM 528–20

Technical Data CM 528–20 230 V, single phase CM 528–20 400 V

Powerful motor on the continuous mixer CM 528.

Large hopper on the continuous mixer easy to fill due to low position.

Practical quick-release device for easy mixing tube removal.

Mortar spraying systemsContinuous mixer www.mortarmachines.comwww.mortarmachines.com

Standard equipment: Frame with 2 wheels, operating instructions and power supply coupling.

Part no. 111 476.002 (230 V single phase)Part no. 111 476.015 (400 V)


78 79MM 2599/10 GB MM 2599/10 GB

Machine model lifting mixer lifting mixer lifting mixer Pump type 2L6 2L6 2L6 Delivery pressure 25 bar 25 bar 25 bar Theor. delivery rate* 5-40 l/min 5-40 l/min 7-40 l/min Delivery distance** 120 m horizontally 120 m horizontally 120 m horizontally Delivery height** 60 m high 60 m high 60 m high Compressor 2-cylinder-compressor 400 l/min, 7 barCompulsory-type mixer 150 l 150 l 150 lHopper 220 l 220 l 220 l Drive motor 3-cylinder Kubota, 18.5 kW*** 4-cylinder Kubota, 22.7 kW at 2,600 rpm at 2,600 rpm Chassis without brakes, road-worthy with brakes, road-worthy Bearing load (tow bar) 60 kg 60 kg 70 kgWeight 750 kg 750 kg 900 kg Length 3,420 mm 3,420 mm 3,924 mm Length without towbar 2,170 mm 2,170 mm - Width 1,420 mm 1,420 mm 1,420 mm Height 1,150 mm 1,150 mm 1,160 mm Filling height 880 mm 880 mm 880 mm Maximum grain size 6 mm 6 mm 6 mm Discharge connection M 50 M 50 M 50 Part no. 111 505.010 (+ DE + HPC) 111 505.120 (+ DE + HPC) 111 505.430 (+ DE + HPC) Part no. 111 505.030 (+ HPC) 111 505.020 (+ HPC)

Technical data SP 11 BMR SP 11 BBR SP 11 BUR


Powerful worm pump 2L6 with discharge connection to hose con-nection.

The maximum engine speed of just 2,600 rpm and the good sound insulation make the SP 11 a machine that is quieter than average.

You can control and programme the complete machine from the control panel.


*** The engine will be changed to the 18.5 kW D 1305 version in the course of 2010. The 15.7 kW D 1105 version will continue to be fitted until then.

Beliso Series – SP 11 BMR, SP 11 BBR, SP 11 BUR

Easy to use plastering machine for ready-mix and site mixes

The sophisticated design and simple operation of the worm pump series SP 11 Beliso are extremely impressive. The machines are suitable for site mixes or bagged interior and external rendering, coloured mortar, lime-stone mortar, base plaster, light wall mortar, ornamental plaster, liquid screed and for filling and grouting work.

SP 11 BMR

PLC Fully hydraulic pump and mixer drive Lifting mixer for convenient filling Excellent soundproofing due to sealed engine compartment Low noise emissions Automatic engine speed adjustment Infinitely variable pumping rate Autom. interval electronics prevent excessive mixing Water metering Mixing time adjuster

Standard equipment:operating instructions, spare parts list, standard tools and cleaning accessories

HPC: High-pressure cleaner, DE: Dust extraction

SP 11 BBR

Features similar to the BMR version, but without PLC and with mechanical water metering and manual speed adjustment.

SP 11 BUR

Features similar to the BMR version, but with 4-cylinder engine, chassis with brakes, mechanical water metering and manual speed adjustment.

Part no. HPC DE111 505.430 l l

Worm pumps


Part Part no. Working light 12 V 474 461 Rubber wiper for window mixer blades 212 652.000 Reduced price for dust extraction cpl., Radio remote control for SP 11 BMR, SP 11 BUR 211 845.009 Vibrating screen compl. MW 10 487 305 Vibrating screen compl. MW 6.3 491 728 Cable remote control 20 m 262 506.009

Worm pump SP 11 BMR


111 505.030 l –


Part no. HPC DE111 505.020 l –

111 505.120 l l

Worm pump SP 11 BUR


80 81MM 2599/10 GB MM 2599/10 GB

Machine model swivel mixer trap mixer Pump type 2L6 2L6 Delivery pressure 25 bar 25 bar Theor. delivery rate* 5-40 l/min 5-40 l/min Delivery distance** 120 m horizontally 120 m horizontally Delivery height** 60 m high 60 m high Air compressor 2-cylinder compressor 400 l/min, 7 barCompulsory-type mixer 150 l 150 l Hopper volume 220 l 220 l Drive motor 3-cylinder Kubota, 18.5 kW at 2,600 rpm*** Chassis without brakes, road-worthy Weight 740 kg 730 kg Bearing load (tow bar) 50 kg 50 kgLength 3,510 mm 3,510 mm Length without towbar 3,210 mm 3,210 mm Width 1,420 mm 1,420 mm Height 1,240 mm 1,220 mm Filling height 1,185 mm 1,125 mm Maximum grain size 6 mm 6 mm Discharge connection M 50 M 50 Part no. 111 505.150 (+ DE + HPC) 111 505.080 (+ DE + HPC) Part no. 111 505.160 (+ HPC) 111 505.180 (+ HPC)

Technical data SP 11 BMB SP 11 BMT


Powerful worm pump 2L6 with discharge connection to hose con-nection.

The maximum engine speed of just 2,600 rpm and the good sound insulation make the SP 11 a machine that is quieter than average.

You can control and identify all machine functions from the central control panel.


*** The engine will be changed to the 18.5 kW D 1305 version in the course of 2010. The 15.7 kW D 1105 version will continue to be fitted until then.

Beliso Series – SP 11 BMB, SP 11 BMT

Easy to use plastering machine for ready-mix and site mixes

The basic versions of the SP 11 Beliso worm pump range have a sophi-sticated and robust design. The machines are suitable for site mixes or bagged interior and external rendering, coloured mortar, limestone mor-tar, base plaster, light wall mortar, ornamental plaster, liquid screed and for filling and grouting work.

SP 11 BMB

Swivel mixer Fully hydraulic pump and mixer drive Excellent soundproofing due to sealed engine compartment Low noise emissions Engine speed adjustment Manual throttle cable Infinitely variable pumping rate Stable plastic hood for easy cleaning, rust-free for its entire service life Mechanical water metering Folding guard bracket

Standard equipment:High-pressure hose and spray lance, standard tools, operating instruc-tions, vehicle coupling.

HPC: High-pressure cleaner, DE: Dust extraction

SP 11 BMT

Trap mixer Fully hydraulic pump and mixer drive Excellent soundproofing due to sealed engine compartment Low noise emissions Manual engine speed adjustment Manual throttle cable Infinitely variable pumping rate Stable plastic hood for easy cleaning, rust-free for its entire service life Mechanical water metering

Standard equipment: identical to SP 11 BMB

Worm pumps


Part Part no. Working light 12 V 474 461 Rubber wiper for window mixer blades 212 652.000 Vibrating screen compl. SP 11 BMT, MW 10 481 038 Vibrating screen compl. SP 11 SP 11 BMT, MW 6.3 487 353

Worm pump SP 11 BMT


111 505.180 l –


111 505.160 l –


Worm pump SP 11 BMB


82 83MM 2599/10 GB MM 2599/10 GB

Suggested accessoriesfor SP 11 Beliso series

Accessories for Monocouche (Monocapa)

Accessories for self levelling floor screed

www.mortarmachines.comwww.mortarmachines.com Suggested accessories for SP 11 Beliso series



Part Part no. Fig. 1x Mortar hose ID 35, V 50, M 35, 13.3 m 207 616.006 1 1x Mortar hose ID 35, V 35, M 35, 13.3 m 207 615.007 2 1x Mortar hose ID 25, V 25, M 24, 5 m 207 808.005 3 1x Air hose Geka 1/2"; 40 m 214 734.007 4 2x Sponge rubber ball ID 35 065 044.001 5 1x Spray gun ID 25-40 short 408 237 6 1x Rubber fine plaster nozzle 8 mm 214 751.006 1x Rubber fine plaster nozzle 10 mm 214 752.005 1x Rubber fine plaster nozzle 12 mm 214 753.004

Part Part no. Fig. 3x Mortar hose ID 50, V 50, M 50, 13.3 m 501 914 1 5x Seal ID 50 213 266.000 2 5x Sponge rubber ball ID 50 000 212.005 3


Part Part no. Fig. 2x Mortar hose ID 50, V 50, M 50, 13.3 m 501 914 1 1x Mortar hose ID 35, V 50, M 35, 13.3 m 207 616.006 2 1x Air hose Geka 1/2"; 40 m 214 734.007 3 5x Seal ID 35 213 725.004 4 5x Sponge rubber ball ID 35 065 044.001 5 5x Seal ID 50 213 266.000 6 5x Sponge rubber ball ID 50 000 212.005 7 1x Base plaster spray gun, short V 35 001 306.004 8 3x PM hose holder, made of leather 000 206.008

Part Part no. Fig. 3x Mortar hose ID 50, V 50, M 50, 13.3 m 501 914 1 5x Seal ID 50 213 266.000 2 5x Sponge rubber ball ID 50 000 212.005 3 1x Air hose Geka 1/2"; 40 m 214 734.007 4 1x Injection lance compl. with T-piece, 001 128.004 5 pressure gauge, remote control air valve, coupling w. nozzle pipe ID 50, mounted expanding collar D45 and collar D 38

Part Part no. Fig. 2x Mortar hose ID 50, V 50, M 50 13.3 m 501 914 1 1x Mortar hose ID 35, V 50, M 35 13.3 m 207 616.006 2 1x Air hose Geka 1/2"; 40 m 214 734.007 3 5x Seal ID 35 213 725.004 4 5x Sponge rubber ball ID 50 000 212.005 6 5x Sponge rubber ball ID 35 065 044.001 5 5x Seal ID 50 213 266.000 7 1x Spray gun V 35 203 054.002 8 3x PM hose holder, made of leather 000 206.008

Part Part no. 1x Rubber fine plaster nozzle 14 mm 214 754.003 1x Rubber fine plaster nozzle 16 mm 214 755.002 1x elastic Mortar nozzle D 18 001 329.007 1x PM hose holder, made of leather 000 206.008

Part Part no. Optional accessories: 1x PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004


Accessories for site mixes

Accessories for injection and grouting

Accessories for preblended dry mortar




Part Part no. 3x PM hose holder, made of leather 000 206.008


Accessories for fire protection mortar

Part Part no. Fig. 1x Mortar hose ID 35, V 50, M 35 13.3 m 207 616.006 1 2x Mortar hose ID 35, V 35, M 35 13.3 m 207 615.007 2 1x Air hose Geka 1/2"; 40 m 214 734.007 3 5x Seal ID 35 213 725.004 4 5x Seal ID 50 213 266.000 7 5x Sponge rubber ball ID 35 065 044.001 5 1x Spray gun V 35 203 054.002 8 3x PM hose holder, made of leather 000 206.008



84 85

KA 230

MM 2599/10 GB MM 2599/10 GB

Part Part no. Sound insulation for P 13 DMR 002 741.008 Water metering fittings with water meter 208 611.000 Ring hitch (truck), with brakes 212 700.004 Ring hitch (truck), without brakes 212 154.003 Ball hitch with brakes 212 704.000 Ball hitch without brakes 212 153.004 T-piece ID 50 for connecting 071 554.006 a pressure gauge Pressure gauge, cpl. 0-100 bar 426 388


Piston pump P 13 KA 230The robust machine with the new pump KA 230 for extremely demanding mixes and all sands up to 10 mm

Piston pumps

The P 13 KA 230 with mechanical pump drive for demanding jobs. The robust double piston pump KA 230 was specially developed to deal with even the most demanding site-made mixes consisting of lime, cement, and all types of sand with a particle size of up to 10 mm. Although it is extremely powerful, it is low-wearing and completely reliable.

Above all, this machine is intended for construction sites throughout the world which are subject to the most demanding conditions. It was there-fore decided to avoid the use of electronic components. All functions and operating elements of the P 13 are purely mechanical and therefore parti-cularly robust and insusceptible to malfunction.

Ideal for: Job-site mixes or exterior and interior plasters in bags, bentonite slurries, special mortars, insulating plasters, cement plaster, lime-cement plaster, lightweight masonry mortar, self levelling floor screed.

Suitable for practically all sands with a particle size of up to 10 mm: Crushed sand, dune sand, washed river/sea sand, desert sand and much more…

P 13 KA 230

specially designed for use with the most demanding site-made mixes powerful 2-cylinder piston pump (1 working pump, 1 balance piston) with new, larger valve head robust and powerful diesel / electric motor output is mechanically adjustable over 3 stages. integrated compressor pneumatic remote control. build-on trap mixer vibrating screen MW 10 mm pressure limiting on outlet

Standard accessories: Agitator in hopper, standard spray gun ID 35, box sieve ID 10 mm, T-piece, pressure gauge 100 bar, operating manual, standard tools, with ring hitch or optional ball hitch

P 13 DMR KA 230

Piston pump drive, 170 l trap mixer, output is mechanically adjustable over 3 stages.

Part no. 111 460.070

P 13 EMR KA 230

Pump drive with electric motor 7.5 kW (11 kW for P 13 SEMR), 170 l trap mixer, output is mechanically adjustable over 3 stages.

Part no. 111 460.080

Piston pump P 13 EMR + KA 230, without brakes

Pump Mechanical piston pump KA 230 Theor. delivery rate 20-80 l/min 30-90 l/minDelivery pressure 40 bar 40 barPiston stroke 130 mm 130 mmPiston diameter 100 mm 100 mm Delivery distance* up to 300 m horizontally, up to 100 m high Air compressor 2-cylinder compressor, 3.5 bar, 300 l/min Drive motor 2-cylinder-Diesel engine electric motor 400 V 12.5 kW at 2,800 rpm 7.5 kW at 2,900 rpm Chassis without brakes without brakesFuse – 20 A Weight 990 kg 990 kgLength 3,000 mm 3,000 mmWidth 1,640 mm 1,640 mmHeight 1,450 mm 1,450 mmFilling height 1,300 mm 1,300 mmMaximum grain size 10 mm 10 mmDischarge connection M 50 M 50 Part no. 111 460.070 111 460.080

Braked version on request on request

Technical data P 13 DMR+ KA 230 P 13 EMR+ KA 230

The P 13 is driven by a powerful 12.5 kW twin cylinder diesel engine. At 2800 revolutions per minute, it works at a relatively low speed and is extremely robust and low-maintenance.

The mechanical vibrator on the large positive mixer prevents the material from bridging and ensures good material flow.




The pressure connections of the new piston pump KA 230 in the P 13 for the hose connection.

Further information is available in brochure MM 3588.For suggested accessories for various applications see pages 86. For additional accessories see page 110 ff.

86 87

7

6

MM 2599/10 GB MM 2599/10 GB

Accessories for floor screed conveyors

Accessories for floor screed conveyors

Standard mortar pipe

Accessories for Injecting

Piston pumps www.mortarmachines.comwww.mortarmachines.com

Suggested accessoriesfor piston pumps P 13

Fig. Part no.40 bar, 50 x 9 mm, length 13.3 m 6 501 91440 bar, 50 x 9 mm, length 20 m 6 501 91510 bar, 50 x 8 mm, length 10 m 6 213 450.00710 bar, 50 x 8 mm, length 20 m 6 213 451.00640 bar, 50 x 9 mm, length 13.3 m (white) 531 33040 bar, 50 x 9 mm, length 20 m (white) 531 331

Individual items for retrofitting* Coupling V 50 / S 50 1 206 604.006Coupling M 50 / S 50 2 211 595.003ID 50, hose, 40 bar, yard ware, 50 x 9 mm 3 501 913ID 50, hose, 40 bar, yard ware, 50 x 9 mm (white) 3 531 327ID 50, hose, 10 bar, yard ware, 50 x 8 mm 3 213 449.0054x hose clip D 68 B 250 E 4 001 046.005Sealing ring for coupling 5 213 266.000

Delivery hoses Mixokret ID 50 cpl. with couplings

Fig. Part no.10 bar, 65 x 10 mm, length 10 m 7 456 83110 bar, 65 x 10 mm, length 20 m 7 456 83210 bar, 65 x 10 mm, length 10 m (white) 531 329

Individual items for retrofitting*Coupling KKV 70 / S 65 1 211 352.000Coupling KKM 70 / S 65 2 211 351.001ID 65, hose, 10 bar, yard ware, 65 x 10 mm 3 001 685.000ID 65, hose, 10 bar, yard ware, 65 x 10 mm (white) 3 531 3284x hose clip D 88, 9 B 19 4 402 292*Sealing ring for coupling 5 010 207.000

* Does not correspond to original/only for repair

Delivery hoses Mixokret ID 65, KK 70, cpl. with couplings



Part no.PM hose holder made of leather 000 206.008

For attaching hoses

Part Part no. Fig. 2x Mortar hose ID 50, V50 / M 50 , 13.3 m 501 914 1 1x Mortar hose ID 50 / 35, 13.3 m 207 616.006 2 1x Air hose 40 m, 1⁄2 ” 214 734.007 3 5x Seal ID 35 213 725.004 4 5x Seal ID 50 213 266.000 5 5x Sponge rubber ball ID 50 000 212.005 6 5x Sponge rubber ball ID 35 065 044.001 7 3x PM hose holder, made of leather 000 206.008


Part Part no. Fig. 5x Seal ID 50 213 266.000 1 5x Sponge rubber ball ID 50 000 212.005 2 3x Mortar hose ID 50, V50 / M 50, 13.3 m 501 914 3 2x Air hose 40 m, 1⁄2 ” 214 734.007 4 1x Injection lance cpl. mit T-piece, 001 128.004 5 pressure gauge, remote control air valve, coupling w. nozzle pipe ID 50, mounted expanding collar D45 and collar D 38 1x PM hose holder, made of leather 000 206.008



88 89

5

4a 4b

2a 2b

1

3

9

6a 6b

7a 7b

8a 8b

10a 10b

5a 5b

4a 4b

2a 2b

1a 1b

3a 3b

2b

8

6

7

MM 2599/10 GB MM 2599/10 GB

Accessories for floor screed conveyorswww.mortarmachines.comwww.mortarmachines.com


Fig. Part no.10 bar, 65 x 10 mm, length 10 m 6 443 67510 bar, 65 x 10 mm, length 20 m 6 443 672

Individual items for retrofitting (integrated externally) only!*Coupling KKV 89 / HR 65 1 213 734.008Coupling KKM 89 / HR 65 2 213 735.007Hose, 10 bar, yard ware, 65 x 10 mm 3 001 685.0008 x washer A 8.4 4 037 107.0028 x round head screw M8 x 25 4 043 198.0058 x hexagon nut M 8 4 034 105.0078 x washer 13 4 037 107.002Sealing ring for coupling 5 002 224.004

Putzmeister couplings for Mixokret hoses with ID 50, ID 65 and ID 70 mm

Universal joint couplings for Mixokret hoses with ID 50-90 mm

M = female partV = male part

Fig. Part no.10 bar, 90 x 11 mm, length 10 m 8 454 406

Individual items for retrofitting*Coupling KKV 108 1 453 503Coupling KKM 108 2 453 504Hose, 10 bar, 90 x 11.5 mm, 10 m, without coupling 3 454 4084x hose clip D 127 B 19 1tlg. 4 016 337.000Sealing ring for coupling O-Ring 124 x 18, NBR 55-60 5 210 580.006 S = nozzle pipe

HR = integrated externally



Fig. Part no.10 bar, 90 x 10 mm, length 10 m 7 455 436

Individual items for retrofitting *Coupling KKV 89 / 90 S 1 455 303Coupling KKM 89 / 90 S 2 455 316Hose, 10 bar, 90 x 11.5 mm, 10 m 3 454 4084x hose clip D 101 - 110 B 20 4 016 337.000Sealing ring for coupling 5 210 580.006

Couplings ID Fig. Part no.KKM 70 / RI 21⁄2“ 1 015 664.004

M 65 / S 65 2a 402 274V 65 / S 65 2b 402 289

M 65 / RI 21⁄2” 402 288V 65 / RI 21⁄2” 3 402 290

M 50 / S 50 4a 211 595.003V 50 / S 50 4b 206 604.006

M 50 RI 2“ 5 211 600.008

Couplings ID Fig. Part no.KKM 70 HR 50 1a 213 736.006KKV 70 HR 50 1b 213 737.005

KKM 70 / 60 S 2a 071 946.009KKV 70 / 60 S 2b 071 945.000

KKM 70 / 65 S 3a H 717 160 00 00KKV 70 / 65 S 3b 211 352.000

KKM 89 HR 65 4a 213 735.007KKV 89 HR 65 4b 213 734.008

KKM 89 / 90 S 5a 065 109.001KKV 89 / 90 S 5b 065 108.002

KKM 70-R 21⁄2” 6a 015 664.004KKV 70-R 21⁄2” 6b 015 197.005

KKM 89-R 21⁄2” 7a 014 895.007KKV 89-R 21⁄2” 7b 209 205.004

KKM 89-R 3” 8a 209 325.007KKV 89-R 3” 8b 073 443.005

KKM 70 / V50 reduction coupling 9 071 790.006

KKV 89, NW 65 mm 10a 455 902KKM 89, NW 65 mm 10b 455 904

KKV 108, 90 S 453 503KKM 108, 90 S 453 504


90 91

7 8

3

2

1

1

3 3

2 21

4a4b

2

1

3

5456 6

5b 5a

6

1222

MM 2599/10 GB MM 2599/10 GB

Quantity Description Fig. Part no. per vesselStandard wear plates: 1x With hole 1 429 862 2x Front / rear 2 429 864 2x On top, crosswise 3 429 865

Highly wear resistant plates: 1x With hole (6 mm) 1 212 322.000 2x Front / rear (6 mm) 2 212 321.001 2x On top, crosswise (6 mm) 3 212 323.009

Plastic wear plates 1x With hole 4 484310 2x Front / rear 5 484311 2x On top, crosswise 6 484312

Bolt set for standard wear plate: 10x Countersunk screw 454 147 10x Cap nut 033 606.002 10x Seal ring 018 891.007

Bolt set for highly wear resistant plates: 10x Countersunk screw 031 366.001 10x Cap nut 033 606.002 10x Seal ring 018 891.007

Bolt set for plastic wear plates: 10x Countersunk screw 202 194.002 10x Cap nut 033 606.002 10x Seal ring 018 891.007

Steel plate for dished boiler ends (4 mm) 2x Front wear plate I 7 430 139 2x Front wear plate II 8 430 140

Set wear plates M 700, M 710, M 740, M 760, cpl. with countersunk screws, cap nuts amd seal rings: 1x Set standard wear plates 524 537 1x Set highly wear resistant plates 214 307.007 1x Set plastic wear plates 492 658

Wear plates for Mixokret M 700, M 710, M 740 and M 760


Mixing paddles for Mixokret

Fig. Part no.Mixing paddle, front 1 205 305.005Mixer plate, front, for Mixokret M 730 1 207 885.002

Mixing paddle, middle, 2 pieces 2 205 306.004Mixer plate, middle, 2 pieces for Mixokret M 730 2 207 886.001

Mixing paddle, rear 3 205 237.005Mixer plate, rear, for Mixokret M 730 3 207 887.000

M 760, M 740, M 730, M 710, M 700: Mixing paddle holder, 2 pieces, rear 4a 205 514.003Mixing paddle holder, 2 pieces, front 4b 205 513.004

M 500: Mixing paddle holder, 3 pieces, inner 5a 471 601Mixing paddle holder, 2 pieces, outer 5b 471 599

Mixer blade kit for Mixokret M 3000 6 206 581.006uand M 700 cpl. in plastic bucket with attachment screwsMixer blade kit for Mixokret M 2000 6 208 583.002item in plastic bucket complete

Fig. Part no. 3x Wear plate with hand-hole 1 401 660 3x Wear plate 2 073 163.000 9x Rubber seal 037 526.007 9x Cap Nut, M 10 033 606.002

Wear plates for Mixokret M 500

Wear plates for Mixokret M 730

Part no. 1x Wear plate I 430 208 1x Wear plate II 430 209

Set of screws and bolts for wear plates: 10x Countersunk screw 043 570.005 10x Cap nut 033 606.002 10x Seal ring 018 891.007

Set wear plates M 730, cpl. with countersunk screws, cap nuts amd seal rings: 1x Set wear plates 524 538

92 93

2 31 4

MM 2599/10 GB MM 2599/10 GB


Fig. Part no.Discharge stand, tripod incl. adapter KK 70 KK 89, detachable legs 517 367Discharge stand, KKM 108, 4 209 811.003

Discharge stands

Wear and spare parts for discharge stands (V)

Part no.Adapter discharge stand ID 50 458 782Adapter discharge stand KK 70 458 783Adapter discharge stand KK 89 496 531Retainer for Adapter discharge stand 499 202TPU rubber pot, natural, for discharge stand 468 004Rubber foot 435 226

Fig. Part no.Discharge stand, tripod Steel, ID 50 1 529 740Steel, KK 70 1 529 741Steel, KK 89 1 529 742

Aluminium, ID 50 2 529 743Aluminium, KK 70 2 529 744Aluminium, KK 89 2 529 745

Fig. Part no.Discharge stand, skid Steel, ID 50 529 746Steel, KK 70 529 747Steel,KK 89 529 748

Aluminium, ID 50 3 529 749Aluminium, KK 70 3 529 750Aluminium, KK 89 3 529 751

94 95MM 2599/10 GB MM 2599/10 GB


Injection branch

Part no. ID 50 015 468.006ID 65 015 162.001

Frequency measuring device

Part no.For checking the belt tension 466 768on the V/ ribbed/ toothed belt

Part no.Extension cable 16 Amp., 230 V 212 960.0063 x 2.5 mm2, 20 mExtension cable 211 457.002with CEE-plug, 16 Amp., 10 m, 5 x 2.5 mm2

Extension cable 214 592.003with CEE-plug, 16 Amp., 25 m, 5 x 2.5 mm2

Extension cable 062 921.004with CEE-plug, 32 Amp., 50 m, 5 x 2.5 mm2

Extension cable 062 922.003with CEE-plug, 32 Amp., 25 m, 5 x 4 mm2

Extension cable 062 923.002with CEE-plug, 32 Amp., 50 m, 5 x 4 mm2

Floor screed smoothing machine EB 600L

Floor screed sleekingplate

Connecting site cable to power supply

Vessel testing device

Part no. With silencer 486 615

Part no.With 230 V, 50 Hz electric gear motor 489 7021.1 kW, 120 kpm, smoothing disc dia. 600 mm, height-adjustable guide frame, cpl. with CEE standard coupling 16 A, gross weight 42 kg

Part no. D 600, light, for nivelling machine EB 600 L H 280 974 1847

Part no. PM hose holder made of leather 000 206.008

For attaching hoses

96 97

1

3

4

2

1

5

4

2

3

1

1

2

3

4

1

6

MM 2599/10 GB MM 2599/10 GB

Accessories for fine concrete pumpswww.mortarmachines.comwww.mortarmachines.com

Accessories for fine concrete pumps

Delivery pipes

Fig. Part no.Delivery pipe SK 50, 3'', 1000 mm 1 081 783.003Delivery pipe SK 50, 3'', 2000 mm 1 081 784.002Delivery pipe SK 50, 3'', 3000 mm 1 081 785.001Delivery pipe SK 65, 3'', 1000 mm 2 057 727.006Delivery pipe SK 65, 3'', 2000 mm 2 057 728.005Delivery pipe SK 65, 3'', 3000 mm 2 057 729.004Delivery pipe SK 100, 4.5'', 1000 mm 3 056 861.002Delivery pipe SK 100, 4.5'', 2000 mm 3 056 862.001Delivery pipe SK 100, 4.5'', 3000 mm 3 056 863.000Delivery pipe SK 100, 4.5'', 6000 mm 3 057 601.009Delivery pipe SK 125, 5.5'', 1000 mm 4 056 849.008Delivery pipe SK 125, 5.5'', 2000 mm 4 056 850.000Delivery pipe SK 125, 5.5'', 3000mm 4 056 851.009Delivery pipe SK 125, 5.5'', 4000 mm 4 087 668.009Delivery pipe SK 125, 5.5'', 6000 mm 4 057 602.008

Elbow pipes

Fig. Part no.Elbow pipe SK 50, 3'', 45° 1 081 779.004Elbow pipe SK 50, 3'', 90° 081 777.006Elbow pipe SK 65, 3'', 45° 057 758.004Elbow pipe SK 65, 3'', 90° 2 057 756.006Elbow pipe SK 100, 4.5'', 15° 057 595.005Elbow pipe SK 100, 4.5'', 30° 057 594.006Elbow pipe SK 100, 4.5'', 45° 057 593.007Elbow pipe SK 100, 4.5'', 90° 3 421 329Elbow pipe SK 125, 5.5'', 15° 057 598.002Elbow pipe SK 125, 5.5'', 30° 258 935.008Elbow pipe SK 125, 5.5'', 45° 057 596.004Elbow pipe SK 125, 5.5'', 90° 261 402.007

T-delivery pipes and reduction pieces

Pressure gauge

Clamp coupling

Spring cotter

Fig. Part no.T-delivery pipe SK 100, 4.5'', 1000 mm 1 057 614.009T-delivery pipe SK 125, 5.5'', 1000 mm 1 057 615.008Reduction pipe SK 65, 3''- SK 50, 3'', 1000 mm 2 058 670.000Reduction pipe SK 100, 4.5''- SK 50, 3'', 1000 mm 3 224 269.009Reduction pipe SK 100, 4.5''- SK 50, 3'', 1500 mm 3 238 508.002Reduction pipe SK 125, 5.5''- SK 100, 4.5'', 1000 mm 4 057 604.006Transmission piece SK 3''/ 2'' IG 027 716.005Transmission piece SK 3''/ 2'' AG 5 082 784.001Lid for T-delivery pipe 4.5'' 6 057 627.009Lid for T-delivery pipe 5.5'' 6 057 628.008

Part no.Pressure gauge SK 4.5'', 100 bar 521 430Pressure gauge SK 5.5'', 100 bar 521 448

Fig. Part no.Clamp coupling SK 3'' 1 417 798Clamp coupling SK 4.5'' 1 431 613Clamp coupling SK 5.5'' 1 417 249

Part no.Spring cotter 018 878.004

98 99

2

1

4

3

5

2

1

3

4

MM 2599/10 GB MM 2599/10 GB


Fig. Part no.Delivery hose SK 50, 3'', 2,000 mm 1 481 169Delivery hose SK 50, 3'', 4,000 mm 1 481 170Delivery hose SK 50, 3'', 5,000 mm 1 481 171Delivery hose SK 50, 3'', 10,000 mm 1 481 172Delivery hose DN 65, 3'', 5,000 mm 2 057 886.002Delivery hose SK 100, 4.5'', 3,000 mm 3 253 319.001Delivery hose SK 100, 4.5'', 4,000 mm 3 083 389.007Delivery hose SK 100, 4.5'', 5,000 mm 3 057 609.001Delivery hose SK 100, 4.5'', 6,000 mm 3 027 623.004Delivery hose SK 125, 5.5'', 2,000 mm 4 027 643.000Delivery hose SK 125, 5.5'', 3,000 mm 4 433 497Delivery hose SK 125, 5.5'', 4,000 mm 4 089 983.009Delivery hose SK 125, 5.5'', 5,000 mm 4 057 612.001Delivery hose SK 125, 5.5'', 6,000 mm 4 057 612.000

Rubber seals

Part no.Rubber seal DN 65, DN 50, 3'' 064 084.004Rubber seal DN 100, 4.5'' 057 341.000Rubber seal DN 125, 5.5'' 055 559.001

additional accessories

Fig. Part no.Pipe clamp for wall or floor, DN 100 3 052 930.005Pipe clamp for wall or floor, DN 125 3 051 038.005Air hose 3/4'', 20 m 416 015PM hose caddy 4 482 464PM pump aid, 18 l storage tank, 25 pcs 5 266 743.004

For cleaning delivery hoses

Fig. Part no.Sponge rubber ball D 60, hard 1 000 212.005Sponge rubber ball D 70, hard 1 258 320.008Sponge rubber ball D 80, hard 1 000 246.000Sponge rubber ball D 120 1 016 091.003Sponge rubber ball D 150, hard 1 223 673.007Sponge rubber ball D 150, medium 1 018 841.002Catch basket for Sponge rubber ball, 4.5'' 2 276 715.006Catch basket for Sponge rubber ball, 5.5'' 2 276 593.008Wash-out adaptor SK 4.5'', for cleaning with compressed air 057 616.007Wash-out adaptor SK 5.5'', for cleaning with compressed air 057 617.006

Concrete spray nozzles

Part no.Plastic concrete spray nozzles ID V 50 mm, 072 157.0041 air tap, 1 tap accessory, 30 mm nozzle diameter, Weight: 3,5 kg

Part no.End hose SK 50, 3'', 6,000mm 292 067.000End hose SK 65, 3'', 5,000 mm 404 454End hose SK 100, 4.5'', 2,850 mm 233 647.007End hose SK 125, 5.5'', 3,000 mm 233 649.005 Support holder for end hose SK 100, 4.5'' 054 370.003Support holder for end hose SK 125, 5.5'' 054 371.002

Delivery hoses

100 101MM 2599/10 GB MM 2599/10 GB


Accessories for fine concrete pumps

RV 10

The RV 10 is a flexible rotary distributor which is ideal for large areas and roofs. Large areas of up to 320 m2 can be concreted from a single position.

Part no. 426 078

Flat gate valves GVM

GVM (gate valve manual) Flat gate valves are simple gate valves. They are opened and closed manually, i.e. using a hammer. They are available for low pressure requirements of up to 20 bar and for high pressure requirements of up to 130 bar.

Part no. 413 087

Part no.Manual gate valve GVM 2/2, 130 bar, SK 125, 5.5'' 413 087Manual gate valve GVM 2/2, 130 bar, SK 100, 4.5'' 222 362.005

Rotary distributors

Rotary distributors are ideal for the simple and flexible delivery and dis-tribution of fine concrete at construction sites. There are 3 different rotary distributor sizes to meet different site conditions.

RV 0

The RV 0 is the smallest rotary distributor in the range. It is particularly suited to cramped construction sites. It consists of a stable hinge to which hoses can be connected if necessary.

Part no. 500 570

RV 7

The RV 7 is suitable for smaller construction sites on roofs or for the con-creting of pillars. The RV 7 is stabilised by 6 individual weights which can be removed when it is transported.

Part no. 455 597

Accessories RV 10 (V)

Technical Data:

Type Pipe delivery line Arms Reach Concreting Transp. dimensions Weight Part no. Pipe - DN (m) area (m2) L x W x H (m) (kg)

RV 0 125 0 0 - 0,8 x 0,5 ø 40 500 570RV 7 125 2 6.58 132 4.2 x 0.6 x 0,8 610 455 597RV 10 125 2 10 320 7.10 x 1.03 x 1.76 1020 426 078

RV 10 in transport position

Part no. Underlay plate, 1 Set, 4 Pieces 481 026

102 103MM 2599/10 GB MM 2599/10 GB

Pitch s (mm)

Stator length l1 (mm)

Rotor length l2 (mm)

Diam

eter

d 1 d 2Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (l/ min) (° Shore) (mm) (bar) R8 1.5 80 78 black 74 4 15 270/113 320 Groove 501 062 500 850 maintenance-free

Accessories for plastering machines

PM Mixer pumps rotors / stators

Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket Rotor for Uni-Mixer (l/ min) (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. Part no.

Bore (B) =

Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket (l/ min) (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (° Shore) (mm) (bar) D6-2 16 6,5 red 68 3 30 200/ 90 250 Groove 425 047 424 846 maintenance-free


= standard equipment

D4 1/4 6 2.5 white 70 3 40 270/ 90 320 Groove 214 573.006 214 572.007 maintenance-free 400 912 D4 1/4 6 2.5 black 65 3 30 270/ 90 320 Groove 402 321 214 572.007 208 129.000 400 912 D4 1/2 12 4.5 green 70 3 40 270/ 90 320 Groove 214 403.008 214 402.009 maintenance-free 400 913 D4 1/2 12 4.5 black 65 3 30 270/ 90 320 Groove 403 523 214 402.009 208 129.000 400 913 D4 20 5.5 red 72 4 20 270/ 90 320 Groove 010 316.001 207 140.006 208 128.001 –D4 20 5.5 yellow 50 4 20 270/ 90 320 Groove 010 313.004 207 140.006 208 128.001 –D5 kurz 40 7.8 brown 72 4 20 270/ 90 320 Groove 071 011.002 071 234 009 208 128.001 400 910D6 Twin 25 6.5 white 73 4 40 270/ 90 320 Groove 406 978 443 740 maintenance-free 400 911 D6 Power 25 6.5 red 73 4 40 270/ 90 320 Groove 206 345.006 443 740 maintenance-free 400 911D6 CP 25 6.5 silver 73 4 40 270/ 90 320 Groove 403 146 443 740 maintenance-free 400 911 D6-3 25 6.5 orange 73 4 40 270/ 90 320 Groove 473 639 473 638 maintenance-free 487 115D6-3 25 6.5 blue 73 4 40 270/ 90 320 Groove 492 020 473 638 208 129.000 487 115 D6-3 action 25 6.5 orange 73 4 40 270/ 90 320 Groove 482 672 473 638 maintenance-free 487 115 D7-2 35 9.0 red 73 4 40 270/ 90 320 Groove 485 478 485 479 maintenance-free – D8-2 40 8.8 black 65 4 30 270/ 90 320 Groove 436 746 436 743 maintenance-free 436 744

Mixer pumps MP 22, MP 25 MIXIT

Mixer pumps MP 22 230 V

D 5 short D 6-2


Mixer pumps MP 25 FMP 60

Rule of thumb: The finer the particle size and the softer the material to be pumped, the harder the required rubber quality for the stator.

The grainier the material and the harder the aggregate, the softer the required rubber quality.

D 4 1/2 D 4 1/4

Assembly aid for rotor-stator Silicone spray, 400 ml spray can

Part no. 508 975

*needs conversion

**depending on material, consistence, delivery range and pressure

Groove (G) =

104 105MM 2599/10 GB MM 2599/10 GB

Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket (l/min) (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (° Shore) (mm) (bar)


*needs conversion(no conversion for S5EV with Part No. 111 452.230 necessary)


Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket (l/min) (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (° Shore) (mm) (bar) D4 4.5 5.5 red 72 4 20 270 / 90 320 Groove 010 316.001 207 140.006 208 128.001 D4 4.5 5.5 yellow 50 4 20 270 / 90 320 Groove 010 313.004 207 140.006 208 128.001

Model Output l/min at 100 rpm** Colour Hard- Max. Pump Length / ø Length Rotor Version Stator Rotor Clamping jacket (l/min) (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (° Shore) (mm) (bar) 2L6 7 - 40 17.0 yellow 73 6 40 540 / 100 620 Groove / Bore 211 355.007 521 150 010 433.007 D6 Power* 3 - 18 6.5 red 73 4 40 270 / 90 320 Groove 206 345.006 443 740 maintenance-free D8-2* 4 - 23 8.8 black 65 4 30 270 / 90 320 Groove 436 746 436 743 maintenance-free 2L6 7 - 40 17.0 yellow 50 6 25 540 / 100 620 Bore 211 355.007 201 111.002 010 433.007 2L6 7 - 40 17.0 yellow 63 6 25 540 / 100 620 Bore 430 837 201 111.002 maintenance-free 2L74 150 63.0 blue 55 8 20 670 / 124 620 Bore 213 018.009 206 395.001 integrated 2L88 8 - 55 21.0 brown 72 6 25 540 / 100 620 Bore 203 509.007 422 650 010 433.007 2L88* 8 - 55 21.0 brown 72 6 25 540 / 100 620 Groove 203 509.007 211 815.000 010 433.007 2L88* 8 - 55 21.0 brown 72 6 25 540 / 100 620 Bore 203 509.007 203 511.008 010 433.007 2L54* 8 - 55 24.0 grey 55 8 25 535 / 124 620 Groove 523 235 211 739.005 integrated

**depending on material, consist-ence, delivery range and pressure


D 6-3 D 6-3 Action D 6 Twin D 6-3 blueD 6 CP D 6 Power

N13 S 16 3,8 grey 73 4 30 160/60 206 Groove 506 905 506 867 –

D4 1/4 1.5 + 3 2.5 white 70 3 40 270 / 90 320 Groove 214 573.006 214 572.007 maintenance-free D4 1/4 1.5 + 3 2.5 black 65 3 30 270 / 90 320 Groove 402 321 214 572.007 208 129.000 D4 1/2 2.5 + 5 4.5 green 70 3 40 270 / 90 320 Groove 214 403.008 214 402.009 maintenance-free D4 1/2 2.5 + 5 4.5 black 65 3 30 270 / 90 320 Groove 403 523 214 402.009 208 129.000 D4 3.5 + 7.5 5.5 rod 72 4 20 270 / 90 320 Groove 010 316.001 207 140.006 208 128.001 D4 3.5 + 7.5 5.5 yellow 50 4 20 270 / 90 320 Groove 010 313.004 207 140.006 208 128.001 D5 kurz 6 + 12 7.8 brown 72 4 20 270 / 90 320 Groove 071 011.002 071 234 009 208 128.001


N13 S

Worm pump Sprayboy P 12 230 V

Worm pump S 5

Worm pump Sprayboy P 12

Mixer pumps MP 10, MP 12

106 107MM 2599/10 GB MM 2599/10 GB


2L6 4 - 40 17.0 yellow 50 6 25 540 / 100 620 Groove 16 211 355.007 211 814.001 010 433.007 2L6 4 - 40 17.0 yellow 50 6 25 540 / 100 620 Groove 16 213 390.002 211 814.001 integrated 2L6 4 - 40 17.0 yellow 63 6 25 540 / 100 620 Groove 16 430 837 211 814.001 maintenance-free 2L88 6 - 55 21.0 brown 50 6 20 540 / 100 620 Groove 16 203 509.007 211 815.000 010 433.007 1,5L74 170 63 green 55 8 15 517 / 124 596 Groove 16 213 027.003 213 028.002 integrated 2L54 8 - 55 24.0 grey 55 8 25 535 / 124 620 Groove 16 523 235 211 739.005 integrated 2L54 8 - 55 24 silver 72 8 25 535 / 124 620 Groove 16 211 738.006 211 739.005 integrated 2L74 0 - 200 45.8 blue 72 8 25 670 / 124 746 Groove 16 213 018.009 212 506.004 integrated2L75 0 - 200 75.0 grey 55 8 20 670 / 124 746 Groove 16 502 911 500 516 maintenance-free



1L6 4 - 25 14.8 yellow 50 6 15 270 / 100 350 Groove 16 214 536.001 214 537.000 422 747


2L6 4 - 40 17.0 yellow 50 6 25 540 / 100 620 Groove 16 211 355.007 211 814.001 010 433.007 2L6 4 - 40 17.0 yellow 50 6 25 540 / 100 620 Groove 16 213 390.002 211 814.001 integrated 2L6 4 - 40 17.0 yellow 63 6 25 540 / 100 620 Groove 16 430 837 211 814.001 maintenance-free 2L88 6 - 55 21.0 brown 50 6 20 540 / 100 620 Groove 16 203 509.007 211 815.000 010 433.007 1.5L74 170 63 green 55 8 15 517 / 124 596 Groove 16 213 027.003 213 028.002 integrated 2L6 7 - 40 17.0 yellow 73 6 40 540 / 100 620 Groove / Bore 211 355.007 521 150 010 433.007


D 6 Power D 4 yellow D 4 red D 8-2 2L88 2L6 2L6 maintenance free Clamping jacket



2L54* 0 - 105 24.0 grey 55 10 25 535 / 124 620 Groove 16 523 235 211 739.005 integrated 2L54* 0 - 105 24 silver 72 8 25 535 / 124 620 Groove 16 211 738.006 211 739.005 integrated 2L74 0 - 200 45.8 blue 55 8 25 670 / 124 746 Bore 206 396.000 206 395.001 maintenance-free2L74* 0 - 200 45.8 blue 72 8 25 670 / 124 746 Groove 16 213 018.009 212 506.004 integrated 2L75* 0 - 200 75.0 grey 55 8 20 670 / 124 746 Groove 16 502 911 500 516 integrated 2L75 0 - 200 75.0 grey 55 8 20 670 / 124 746 Bore 487 262 487 261 maintenance-free

*needs conversion


Worm pumps SP 11 BUR

Worm pump SP 5

Worm pumps SP 11 BMR, BMB, BMT, BBR

Worm pumps SP 11 BHF

108 109MM 2599/10 GB MM 2599/10 GB

7515 5 - 250 83 white 63 8 35 500 / 159 623 Hexagonal 525 052 433 023 maintenance-free 2L8 8 - 400 150 white 63 10 25 650 / 194 740 Hexagonal H7000 508 312 H7000 508 021 maintenance-free

2L4 P4 5.3 yellow 50 4 20 360 / 75 407 Groove 010 325.005 010 321.009 010 329.001 2L4 P4 5.3 red 72 4 25 360 / 75 407 Groove 010 326.004 010 321.009 010 329.001 2L4 P4 5.3 green 72 4 25 360 / 75 407 Groove 010 677.009 010 321.009 010 329.001 D3 TS3 10.0 red 72 4 25 315 / 70 379 Groove 072 996.003 072 997.002 073 487.003 D3 TS3 10.0 green 72 4 25 315 / 70 379 Groove 201 175.006 072 997.002 073 487.003 D5 * MS-x, S 5 12.0 brown 65 4 20 350 / 90 400 Groove 070 352.005 070 351.006 206 848.008 3L7 SP 11 BUR 17.0 yellow 50 6 40 534 / 100 620 Groove 16 213 638.007 211 278.003 maintenance-free 3L7 SP 11 BUR 17.0 yellow 75 6 40 534 / 100 620 Groove 16 211 503.008 211 278.003 maintenance-free 3D7 UMP 17.0 red 71 6 40 534 / 100 620 Groove 16 208 276.005 208 263.005 maintenance-free 2L6 FMP 17.0 yellow 50 6 25 540 / 100 620 Groove 12 211 355.007 010 628.003 010 433.007 2L88 FUMP 70 21.0 brown 50 6 25 540 / 100 620 Groove 14 203 509.007 208 316.004 010 433.007 2L88 UMP 21.0 brown 50 6 25 540 / 100 620 Bore 203 509.007 422 650 010 433.007 2L74 P11SDVF 63.0 blue 55 8 25 670 / 124 620 Bore 206 396.000 206 395.001 maintenance-free 2D8 FUMP, SP 11 E 45.9 red 72 4 25 600 / 145 570 Groove 208 537.003 208 467.005 maintenance-free 1,5L8 S8 123 yellow 50 10 15 660 / 190 747 Bore 070 162.004 200 770.004 073 827.003


Model Usage l/ min at 100 rpm** Colour Hard- Max. Pump Length/ ø Length Rotor Version Stator Rotor Clamping jacket in machine (75 % sphere) ness grain size pressure stator (mm) without pin (mm) Rotorhead Part no. Part no. Part no. (° Shore) (mm) (bar)



Worm pumps SP 20

Other worm pumps

2L74 3L7 2L54 2L75 2L8 2L88


*needs conversion


110 111

1

2

6

MM 2599/10 GB MM 2599/10 GB

Part no.Dynamat in-line mixer with mortar hose 111 511.0062 m, ø 35 mm, connection cable 2 m for Mixer pump (Fig. 1)Uni in-line mixer (Fig. 2) 400 566(Accessories: see rotors with pins)Cross shaped mixing paddle (for uni in-line mixer) 400 5802 x collar nuts 208 801.001PM-coupling V 35 / 25-40 reduced 207 795.008Pressure gauge 0-60 bar for hoses DN 25-40 214 570.009Pressure gauge 0-60 bar for hoses DN 35-40 472 506

In-line Mixer Mortar hoses up to 40 bar operating pressures (yard wear)

Part no.ID 25 mm, yard ware 25 x 7 mm, as of 40 m roll 001 602.009ID 25 mm, yard ware 25 x 7 mm, as of 40 m roll (white) 531 324ID 35 mm, yard ware 35 x 8 mm, as of 40 m roll 001 603.008ID 35 mm, yard ware 35 x 8 mm, as of 40 m roll (white) 531 326ID 50 mm, yard ware 50 x 9 mm, as of 40 m roll 501 913ID 50 mm, yard ware 50 x 9 mm, as of 40 m roll (white) 531 327

Pressure gauge, pressure control device, T-piece

Pressure gauge for ID 50 Part no.with coupling V 50 / grease buffer, 0-6 bar 011 729.008with coupling V 50 / grease buffer, 0-10 bar 011 730.000with coupling V 50 / grease buffer, 0-25 bar 426 387with coupling V 50 / grease buffer, 0-40 bar, ø 60 mm 420 989with coupling V 50 / grease buffer, 0-100 bar 426 388T-piece to pressure gauge ID 50 mm 071 554.006

Pressure control device and pressure gaugePressure control device cpl. with grease buffer 2-32 bar 011 757.009Protective cap for pressure gauge NG 100 001 252.006Air-testing pressure gauge 1”, T-piece 0-6 bar 001 160.004Testing pressure gauge with 1” hose tap ID 25 014 375.006Testing pressure gauge with 1” hose tap ID 25-40 208 745.002Pressure gauge 0-60 bar for hoses DN 25-40 214 570.009Pressure gauge 0-60 bar for hoses DN 35-40 472 506


For attaching hoses

Part no.PM hose holder made of leather 000 206.008


Fig. Part no.40 bar, 25 x 7 mm, length 5 m 6 207 803.00040 bar, 25 x 7 mm, length 10 m 6 207 804.00940 bar, 25 x 7 mm, length 15 m 6 211 966.00140 bar, 25 x 7 mm, length 20 m 6 207 806.007 40 bar, 25 x 7 mm, length 20 m (white) 531 341

Individual items for retrofitting*Coupling V 25-40 / S 25 1 208 828.000Coupling M 25-40 / S 25 2 211 593.005ID 25 yard ware 25 x 7 mm 3 001 602.0094x hose clamp, NW 25, B 200 E 4 002 337.001Seal for coupling 5 207 764.000

Mortar hoses cpl. with couplings, ID 25, 40 bar, M 25-40, V 25-40

Part no.40 bar, 20 x 7 mm, length 10 m 211 508.003

Mortar hoses cpl. with couplings, ID 20, V 25-40 Geka

M = female partV = male partS = nozzle pipe


112 113

5

6

6

6

MM 2599/10 GB MM 2599/10 GB




Fig. Part no.40 bar, 25 x 7 mm, length 5 m 5 207 808.00540 bar, 25 x 7 mm, length 10 m 5 207 809.004

Individual items for retrofitting*Coupling V (a) V 25-40 / S 25 2a 208 828.000Coupling V (b) V 35 / S 25 2b 214 800.009ID 25 yard ware 25 x 7 mm 3 001 602.0094x Hose clamp ID 35, D 250 e 4 002 337.001

Mortar hoses complete with couplings, ID 25, 40 bar, V 35, V 25-40

Mortar hoses complete with couplings, ID 35, 40 bar, M 35, V 35

Fig. Part no.40 bar, 35 x 8 mm, length 2 m 6 070 335.00640 bar, 35 x 8 mm, length 13.3 m 6 207 615.00740 bar, 35 x 8 mm, length 20 m 6 209 950.00340 bar, 35 x 8 mm, length 13.3 m (white) 531 340

Individual items for retrofitting* Coupling M 35 / S 35 1 211 594.004Coupling V 35 / S 35 2 206 606.004ID 35, 35 x 8 mm, yard ware 3 001 603.0084x Hose clamp ID 35 B 250 e 4 002 331.007Sealing for coupling 5 213 725.004

Fig. Part no.40 bar, 50 x 9 mm, length 13.3 m 6 501 91440 bar, 50 x 9 mm, length 20 m 6 501 91540 bar, 50 x 9 mm, length 13.3 m (white) 531 33040 bar, 50 x 9 mm, length 20 m (white) 531 331

Individual items for retrofitting* Coupling M 50 / S 50 1 211 595.003Coupling V 50 / S 50 2 206 604.006ID 50, 50 x 9 mm, yard ware 3 501 9134x Hose clamp ID 50 B 250 e 4 001 046.005Sealing for coupling 5 213 266.000

Mortar hoses complete with couplings, ID 50, 40 bar, M 50, V 50,

Fig. Part no.40 bar, 35 x 8 mm, length 13.3 m 6 207 616.006

Individual items for retrofitting* Coupling M 50 / S 50 1 211 594.004Coupling V 50 / S 35 2 207 621.004ID 35, 35 x 8 mm, yard ware 3 001 603.0084x Hose clamp ID 35 B 250 e 4 002 331.007Sealing for coupling 5 213 725 004

Mortar hoses complete with couplings, ID 35, 40 bar, M 35, V 50


* Does not correspond to original/only for repair* Does not correspond to original/only for repair


114 115

4

5

7

8

9

11

6

23

1

10

12

13

MM 2599/10 GB MM 2599/10 GB


Putzmeister couplings for mortar hoses with 25-50 mm ID

Fig. Part no.M 25-40 / RI 1” 1 211 597.001

M 35 / RI 1” 2 211 598.000M 35 / RI 11⁄2” 2 211 599.009M 50 / RI 2” 2 211 600.008M 35 / RA 1 1⁄2” 2 070 315.000M 50 / RA 2” 2 211 848.006

V 25-40 / RI 1” 3 207 763.001V 25-40 / RI 1 1⁄2” 3 207 813.003V 35 / RI 1” 3 207 618.004V 35 / RI 1” plastic 3 203 135.002V 35 / RI 1 1⁄2” 3 070 316.009V 35 / RI 2” 3 208 453.006V 35 / RI 5⁄4” 3 207 635.003V 50 / RI 2” 3 205 273.001V 50 / RI 1” 3 207 629.006V 50 / RI 21⁄2” 3 210 793.000

M 25-40 / S 25 5 211 593.005M 35 / S 35 5 211 594.004

M 50 / S 50 6 211 595.003

V 25-40 / S 25 7 208 828.000V 35 / S 25 7 214 800.009

V 35 / S 35 8 206 606.004

V 50 / S 50 9 206 604.006V 50 / S 35 9 207 621.004

V 35-V 25 / 40 reduced 11 207 795.008

M 25 / 40-V 25 12 208 838.003

V 50 - M 35 reduced 13 213 217.004M 50 - V 35 reduced 13 211 290.007 V 50 Dummy lid 10 208 454.005

Rotary feedthrough

Part no.M 25-40 / RI 1” aluminium coupling cpl. 403 330

Hose nozzles with thread for mortar hoses with 20-50 mm ID

Part no.S-nozzle pipe 20 mm RA 1” 211 536.004S-nozzle pipe 25 mm RA 1” 205 464.001S-nozzle pipe 35 mm RA11⁄2” 205 465.000S-nozzle pipe 50 mm RA 2” 205 466.009



Sealing rings

Hose clips

Part no.ID 1⁄2“ mm, for air hose B17 Oe. 002 333.005ID 25 mm, for mortar hose B20 Oe. 002 337.001ID 35 mm, for mortar hose B25 Oe. 002 331.007ID 50 mm, for mortar hose B25 Oe. 001 046.005ID 65 mm, 2-pieces, for mortar hose B25 015 288.008ID 65 mm, 1-piece, for mortar hose 402 292ID 90 mm, for mortar hose 016 337.000ID 98 mm, for suction hose 002 247.007

Cam levers

Part no.Cam lever, reinforced, forged steel 211 535.005Heavy duty shaft dowel pins with reinforcement: (10 each in a set)– for 35 and 25 M-Teil, Gr. 6 / 30 and 3.5 / 30 441 055– for 50 M-part, size 6 / 40 and 3.5 / 40 441 056Shaft dowel pin for 25 and 35 6 x 28 211 613.008Shaft dowel pin for 25-40 6 x 30 211 609.009Shaft dowel pin for 50 6 x 36 211 610.001Safety ring for cam lever 001 698.000

Part no.ID 25-40 mm, 42 x 27 x 6 mm 207 764.000ID 35 mm, 54 x 37 x 6 mm 213 725.004ID 50 mm, 67 x 51 x 6 mm 213 266.000

116 117

31

2

MM 2599/10 GB MM 2599/10 GB

GEKA quick-couplings for water- and air hoses 3⁄8”-1” ID

Part no.Seal, GEKA plus 413 895Seal 002 313.009S 3⁄8” 018 535.004S 1⁄2” 002 312.000S 3⁄4” 001 387.007S 1” 001 390.007RA 3⁄8” 041 403.006RA 3⁄4” 001 386.008RA 1” 062 815.000RA 11⁄4” 062 861.009RA 1⁄2” 014 068.009RI 1⁄2” 062 621.003RI 3⁄4” 002 311.001RI 1” 001 391.006RI 11⁄4” 062 622.002RI 3⁄8” 424 458

S = nozzle pipeRA = external threadRI = internal thread

EWO coupling

Part no.RA 1⁄2” 213 269.007

Hose clip

Width Hose external Part no.8.1 mm ø 6-16 mm 002 333.00514.3 mm ø 32-50 mm 002 332.00614.3 mm ø 40-60 mm 002 334.00412.0 mm ø 20-32 mm 001 422.00112.0 mm ø 57 mm 001 433.00312.2 mm ø 44-56 mm 001 421.002

Hose clamps for air hoses

Width Hose external Part no.8 mm ø 15-17 mm 002 328.0078 mm ø 17-20 mm 002 329.0068 mm ø 20-23 mm 002 330.008

Sponge rubber balls

Part no.for cleaning the delivery hosesfor delivery hose ID 18 mm, ø 20 mm 429 483for delivery hose ID 20 mm, ø 25 mm 429 485for delivery hose ID 25 mm, ø 30 mm 000 239.004for delivery hose ID 35 mm, ø 45 mm 065 044.001for delivery hose ID 50 mm, ø 60 mm 000 212.005

www.mortarmachines.comwww.mortarmachines.com Accessories for plastering machines

Ground plaster spray guns – made of aluminium – for wet mortar, job site mixes

Version Nozzles ø Weight Fig. Part no.short, 185 mm, straight K 20, 16 mm 1.4 kg 1 001 306.004short, 700 mm, angular K 20 mm 1.5 kg 209 307.009long, 1,300 mm, angular K 20 mm 1.7 kg 2 209 308.008

Up to grain size of 8 mm, it can be used for first spray and base coat plasters as well as for rough cast and insu lating plasters, mainly suitable for construc-tion site mixes but also for ready-mixed material. Max. throughput up to 40 l/ min, air requirement approx. 200 - 400 l/ min. All 3 spray guns with male coupling 35 mm and 2 air ball valves.

Collar nozzles

ø Part no.18 mm 001 329.00720 mm 001 330.009

Water air-hose 3⁄4”

Part no.Water air-hose, GEKA-coupling 3⁄4” ID, length 40 m 210 789.001Spray nozzle, GEKA-coupling 1⁄2” ID, lockable 042 419.002

Air hose 1⁄2”

Coupling Length Part no.GEKA 1⁄2” ID 10 m 001 682.003GEKA 1⁄2” ID 15 m 212 333.002GEKA 1⁄2” ID 20 m 001 665.004GEKA 1⁄2” ID 30 m 202 911.007GEKA 1⁄2” ID 40 m 214 734.007

Hose connectors for mortar hose wih air hose

Part no.ø 25 mm hose with ø 13 mm hose, 214 579.000plastic clamp – black – (Illustrations may differ from the original)

118 119

1

3

4

5

2

MM 2599/10 GB MM 2599/10 GB

Spray nozzles for texture plaster spray gun

ø Part no.4 mm 000 225.0056 mm 000 227.0038 mm 000 229.0019 mm 000 230.00310 mm 000 231.002

Spray guns for texture plaster

Up to a grain size of approx. 4-6 mm – for mineral spray or dispersion pla-sters as well as for sealing slurries, fillers, etc. Throughput up to 10 l/ min, air requirement 400-800 l/ min.

ID Nozzles ø Weight Part no.

M 25 mm 4, 6, 8 mm 2.2 kg 071 473.006M 25-40 mm 4, 6, 8 mm 2.2 kg 208 751.009

Material nozzles for texture plaster spray gun

ø Diameter/ Version Part no.12 mm Air bore holes ø 3 mm – red 206 734.00212 mm Air bore holes ø 2 mm – silver 206 751.001


Spray guns for fine plaster with swivel coupling

Part no.Spray gun w. swivel coupling ID 25-40, with 6.5 mm nozzle 529 733

ø Part no.6.5 mm (for 1.5 mm grain size) 470 3948 mm (for 2 mm grain size) 470 39510 mm (for 3 mm grain size) 470 39712 mm (for 4 mm grain size) 470 39814 mm (for 5 mm grain size) 470 39916 mm (for 6 mm grain size) 470 400

ID Ball valve Air cock Version Nozzle ø Weight Fig. Part no.M 25-40 mm yes 2 short 14 mm 2.4 kg 5 408 237with rotating coupling 300 mmM 25-40 mm – 1 short 14 mm 1.2 kg 1 402 592with rotating coupling 405 mm MP 25 StandardM 25-40 mm – 1 long, 14 mm 2.6 kg 1 403 812with rotating coupling 1.460 mmM 25-40 mm – 1 long, 14 mm 1.2 kg 2 404 479with rotating coupling 770 mmand angled aluminum head M 25-40 mm – 1 long, 14 mm 1.5 kg 2 404 361with rotating coupling 1.185 mmand angled aluminum head V 35 mm – 1 short, 14 mm 0.6 kg 3 203 054.002 285 mmV 35 mm yes 1 short, 14 mm 0.65 kg 4 209 174.009 450 mm

Up to grain size 4 mm for all dry ready- mix motar that have to be prepared, e.g. gypsum plaster, lime-cement plas ters, etc. Max. throughput 30 l/min, air requirement approx. 200 l/min.

Fine plaster spray gun – made of plastic – for ready-mix mortar

Quality-PE Quality-PUø Part no. Part no.8 mm 214 751.006 417 55610 mm 214 752.005 417 97412 mm 214 753.004 410 98214 mm 214 754.003 417 55416 mm 214 755.002 417 555

Rubber fine plaster nozzles

Spray nozzles

ø Part no.10 mm 521 64012 mm 521 64114 mm 521 64216 mm 521 643

Conical plaster nozzles

120 121

1

2

3

2

1

MM 2599/10 GB MM 2599/10 GB

Applying nozzles

Part no.RI1”/ GEKA Mortar applying nozzle 160 mm 071 566.007

Refurbishing spray gun

Part no.ID 1”, ø 12 mm nozzle, weight 1.2 kg 207 283.002ID V 35/ RI1”, coupling connection – plastic 203 135.002ID M 25-40/ RI1”, coupling connection 211 597.001

Nozzles Vulkollanø 15 mm 207 286.009

Up to grain size of 6 mm for mineral-based plasters for refurbishing, for concreting with ring nozzle and flexible spray pipe.

Concrete spray nozzles, plastic

ID Air cock Cock-addit Nozzles ø Weight Part no.V 35 mm 1 1 28 mm 3.0 kg 011 780.005V 50 mm 1 1 30 mm 3.5 kg 072 157.004

ID Fig. Part no.DN 10 Jointing device with tangential sprayhead 1 415 689 jointing nozzle, swivel coupling M 25-40DN 25 Frame filling unit with ball valve, 2 214 236.000 rotating coupling M 25-40, 20 m el. remote control cable, (for MP, SP 5 + Sprayboy) Remote control cable with plug with binder plug 3 214 254.008 and switch, 20 m longDN 25 Frame connector filling hose 408 373 with coupling M 25-40, 30 cm long Electric remote control with 3 269 446.007 on-off switch (binder plug), 60 m Electric remote control cable with plug (binder) 3 211 507.004 for extension 30 m Electric remote control cable with plug (binder) 3 211 506.005 for extension 20 m, 3 x 0,75 Electric remote control cable with plug (binder) 3 211 505.006 for extension 10 m, 3 x 0,75

Guns for bonding material

Part no.Bonding gun in case 408 422consisting of:bonding gun, cpl, tool case, cleaning brush D, grease gun – small, adapter cable 4P harting/ binder

Plus: 30 m remote control cable 211 507.004, 20 m remote control cable 211 506.005or 10 m remote control cable 211 505.006.

Adhesive gun with case


Power cable / construction site lead

Part no. Extension cable 16 Amp., 230 V 212 960.0063 x 2.5 mm2, 20 mConstruction site lead with CEE plug 211 457.00216 Amp., 10 m, 5 x 2.5 mm2

Construction site lead with CEE plug 214 592.00316 Amp., 25 m, 5 x 2.5 mm2

Construction site lead with CEE plug 062 921.00432 Amp., 50 m, 5 x 2.5 mm2

Construction site lead with CEE plug 062 922.00332 Amp., 25 m, 5 x 4 mm2

Construction site lead with CEE plug 062 923.00232 Amp., 50 m, 5 x 4 mm2

122 123

2

3

1

4

5

MM 2599/10 GB MM 2599/10 GB

Fig. Part no.Compressor, 200 l/min, 400 V / 50 Hz 1 481 074without cut-off (MP serie)Compressor, 200 l/min, 400 V / 50 Hz 487 420with cut-offCompressor, 200 l/min, 230 V / 50 Hz 481 087with cut-off

Fig. Part no. Compressor Strocomp 433, AC, 230 - 250 V / 50 Hz, 2 111 593.008400 l/min suction, 300 l/min delivery, 2 x 5l tank content, 10 bar, 2.2 kW, 81 x 47 x 52 cm, 67 kgCompressor Strocomp 864, AC, 230 - 250 V / 50 Hz, 3 111 593.011800 l/min suction, 550 l/mindelivery 2 x 5l tank content, 10 bar, 2 x 2.2 kW, 75 x 55 x 61 cm, 71 kg

Fig. Part no.Compressor HANDY, 250 l/ min, 400 V/ 50 Hz, 3-phased 4 000 235.008Compressor HANDY, 250 l/ min, 230 V/ 50 Hz, 1-phased 4 000 215.002

Fig. Part no.Coupling 1⁄4” GEKA (*) 207 969.009(*) is required if compressor is not used in connection with mixer pump.

Compressor V-MEKO 400, 360 l/min, 5 400 168400 V / 50 Hz with pressure switch-off Compressor V-MEKO 400, 360 l/min, 5 205 767.009400 V / 50 Hz without pressure switch-off Compressor 590 l/min, 10 bar, 3 kW, 5 213 264.0022 x 10 l air accumulatorCompressor V-MEKO, 360 l/min, 1 x 220 V / 50 Hz 5 213 271.008Compressor V-MEKO, 360 l/min, 1 x 220 V / 50 Hz, 5 464 452with pressure switch-offCompressor V-MEKO, 360 l/min, 3 x 380 V 5 213 271.008Compressor V-MEKO, 360 l/min, 3 x 220 V / 60 Hz 5 210 072.006Compressor V-MEKO, 360 l/min, 3 x 220 V / 60 Hz 5 462 267with pressure switch-off

Compressor

Part no.Injection lance cpl. with T-piece, pressure gauge 001 128.004Remote control air cock, coupling with nozzle pipe ID 50, Expanding collar D 45 and mounted collar D 38

Injection lance as above but without T-piece, 001 133.002Pressure gauge and remote control cock, conn. V 35 / RI 1”

Expanding collar D 38 070 344.000Expanding collar D 45 070 345.009

Injection lances

Part no.Hopper gun cpl. with air hose in box 207 307.001Hopper gun without hose and packaging 210 014.006Air hose with EWO plug coupling, 10 m 209 345.003Air hose with EWO plug nipple/ GEKA coupling 207 958.007Holder for hopper gun 206 766.009Corner piece 001 430.006

hopper guns with accessories

Wear parts

Part no. Wear parts kit 210 199.002

consisting of:Pressure spring (2 pieces) 001 413.007Hose clamp (1 piece) 001 421.002O-ring ø 42 mm (2 pieces) 042 731.007O-ring ø 19 mm (2 pieces) 041 039.001

Diaphragm (2 pieces) 206 697.000Guiding nozzle (1 piece) 206 702.005Air nozzle D 3.2 (1 piece) 208 346.003Knurled nut M5 (2 pieces) 206 703.004

Water pressure – booster pump

Part no.Auxiliary water pump, self-priming 423 324with check valve in the suction line, 230 V / 50 Hz, 0.33 kW, 3.4 m3/h, max. delivery pressure 6 barAuxiliary water pump, self-priming 422 097with check valve in the suction line, 400 V / 50 Hz, 0.33 kW, 3.4 m3/h, max. delivery pressure 6 bar,with hard plugAuxiliary water pump, self-priming 435 229with check valve in the suction line, 400 V / 50 Hz, 0.33 kW, 3.4 m3/h, max. delivery pressure 6 bar,with CEE plugWater pump 3.4 m3/h, self-priming with 429 706automatic switch, 230 V / 50 Hz, 0.75 kW, water protected IP 65, with check valve in suction line


124 125

1

2

MM 2599/10 GB MM 2599/10 GB

For cleaning the delivery hoses

Sponge rubber balls ø mm Part no.for delivery hose ID 18 mm 20 429 483for delivery hose ID 20 mm 25 429 485for delivery hose ID 25 mm 30 000 239.004for delivery hose ID 35 mm 45 065 044.001for delivery hose ID 50 mm 60 000 212.005for delivery hose ID 60 + 65 mm 80 000 246.000for delivery hose ID 60 + 65 mm 70 258 320.008for delivery hose ID 90 + 100 mm 120 016 091.003

For cleaning and maintenance

Part no.PM hand lever grease gun with hose 000 211.006Grease cardridge with high performance lubr. grease, 400 g 000 113.007Grease gun – small – 000 112.008Cleaning brush 000 100.007

PM spray gun including 5 m hose 000 210.007Cleaning spray gun V 35, alu. – short – 211 564.005without nozzle with air fittingsNozzle, steel ø 6/12 210 180.008Nozzle, steel ø 8/14 210 127.003Nozzle, steel ø 10/16 210 126.004Nozzle, steel ø 12/18 210 129.001

Part no.Cleaning and care detergent “Limpiol” 354 410 13920 l canister (enough for approx. 400-600 m2), biologically decomposable

Part no.PM pumping aid, 18 l in storage tank, 25 pcs 266 743.004

General accessories

General accessories

Machines and working accessories

Fig. Part no.Wheel chock – steel-plate 636 1 015 006.002Wheel chock – plastic UK 10 2 415 904Wheel chock – plastic UK 36 2 484 954Bracket for UK 36 484 956Bracket for UK 10 415 905Bracket for 636 061 362.004

Part no.Lighting set 13 pin connector, 12 V 496 2611.6 m cableLighting set 13 pin connector, 24 V 507 1771.6 m cable

Part no.Lighting set, width: 1 m 7 pin connector, 24 V 209 028.0036 m cableLighting set, width: 1 m 7 pin connector, 12 V 207 525.0036 m cable

Part no.Vehicle cable adapter 7 - 13 pin, 12 V 437 679Vehicle cable adapter 13 - 7 pin, 12 V 248 012.009

Part no.Number plate holder 362 732.003with folding frame

Part no.Soft dock, coupling guard 491 951for ball head couplings on Alko chassis (M 760, M 740, M 730)


126 127

8

9

1

2

3

4

5

6

7

1

2

3

4

6

7

5

6

7

8

3

2

4

5

1

1

2

3

4

5

6

7

9

8

MM 2599/10 GB MM 2599/10 GB

Toolsets

Toolswww.mortarmachines.comwww.mortarmachines.com

Part Part no. Fig. 1x Smoothing trowel 280 x 130 x 0.7 mm 063 245.006 1 1x “Swiss“ Smoother 800 x 130 x 0.7 mm 063 243.008 2 1x Facade spattle 350 mm 531 714 3 1x Plasterer's trowel stainless steel 70 mm 064 071.004 4 1x Berner plastering trowel, stainless steel 140 mm 363 174.000 5 1x Mesh scraper 363 165.006 6 1x Plasterer's float w. sponge rubber cover, coarse pore 063 236.002 7

1x Alu float w. wood handle, 1,800 mm 000 201.003 8 1x Alu-H-shaped float, 1,000 mm 000 190.004 9

Toolset site mixes

Complete set, Part no.: 531 755Set, pos. 1-7, Part no.: 531 754 consisting of:

Part Part no. Fig. 1x Plasterer's float w. sponge rubber cover, coarse pore 063 245.006 1 1x Plasterer's float w. sponge rubber cover, fine pore 531 759 2 1x PU Plasterer's float 280 x 140 mm 363 180.007 3 1x PU Plasterer's float 420 x 220 mm 362 312.009 4 1x Smoothing trowel plastic, 280 x 140 x 3 mm 363 150.008 1x Berner plastering trowel, stainless steel 140 mm 363 174.000 5 1x Facade spattle 350 mm 531 714 6 1x Plasterer's trowel stainless steel 70 mm 064 071.004 7

Toolset Finish

Complete set, Part no.: 531 756 consisting of:

Part Part no. Fig. 1x “Swiss“ Smoother 800 x 130 x 0.7 mm 063 243.008 1 1x Floor-layer smoothing trowel 500 x 90 x 1.2 mm 362 308.000 2 1x Floor-layer smoothing trowel 700 x 90 x 1.2 mm 362 310.001 3 1x pair of spikes, screed shoe 531 746 4 1x Knee protectors, box form 362 343.007 5

1x measuring floats 100 cm 362 315.006 6 1x measuring floats 200 cm 362 317.004 7 1x measuring floats 300 cm 362 319.002 8

Toolset floor screed


Part Part no. Fig. 1x Mesh scraper 063 240.001 1 1x Smoothing trowel 280 x 130 x 0.7 mm 063 245.006 2 1x “Swiss“ Smoother 500 x 130 x 0.7 mm 063 243.008 3 1x Facade spattle 350 mm 531 714 4 1x Plasterer's trowel stainless steel 70 mm 064 071.004 5 1x Berner plastering trowel, stainless steel 140 mm 363 174.000 6 1x Plasterer's float w. sponge rubber cover, fine pore 531 759 7

1x Alu-H-shaped float, 1,000 mm 000 190.004 8 1x Alu-H-shaped float, 2,000 mm 000 190.000 9

Toolset dry mortar


128 129MM 2599/10 GB MM 2599/10 GB

Smoothing trowel in steel version with cylindrical wooden handle 280 x 130 x 0.7 mm 362 311.000

PU plasterer’s float made of polyurethan 280 x 140 mm 363 180.007 320 x 180 mm 363 181.006 420 x 220 mm 362 312.009 480 x 240 mm 362 313.008

ToolsPractical tools for craftsmen in the building line

Alu-H-shaped float Profile 114 x 50 x 28 mm 1.0 m 000 190.004 1.2 m 000 191.003 1.5 m 000 192.002 1.8 m 000 193.001 2.0 m 000 194.000

Alu float with wood handle 1.2 m 000 202.002 1.5 m 000 200.004 1.8 m 000 201.003

Alu-trapezoidal-float profile 97 x 17 mm 1.0 m 000 195.009 1.2 m 000 196.008 1.5 m 000 197.007 1.8 m 000 198.006 2.0 m 000 199.005

For plasterers

Plasterer’s float 140 x 280 mm, 063 236.002 with sponge rubber cover, coarse-pore

Sponge rubber pad for float 280 x 140 mm 063 235.003 with sponge rubber cover, coarse-pore

Cleaning brush stickleback 064 073.002

Trowel Freiburger trowel, 063 375.002 Nirosta, stainless steel

Plasterer’s trowel stainless steel, 70 mm 064 071.004 stainless steel, 80 mm 363 163.008 stainless steel, 100 mm 363 164.007

Tools

Mesh scraper 290 x 150 mm 063 240.001 370 x 170 mm 363 165.006 galvanized


Smoothing trowel in steel version with special wooden handle 280 x 130 x 0.7 mm 063 245.006

Smoothing trowel Plastic 280 x 140 x 3 mm 363 150.008

Berner plastering trowel with soft-grip handle stainless steel 140 mm 363 174.000

Trowel stainless steel, with straight neck 160 mm 363 173.001 180 mm 063 375.002

130 131MM 2599/10 GB MM 2599/10 GB

Finishing coat scraper tapered 531 744

Plaster spatula with BIT 150 mm 531 747

Small plasterer’s plane 330 x 40 mm 531 743

For plasterers

Plasterer’s float 140 x 280 mm, 531 759 with sponge rubber cover, fine-pore

Sponge rubber pad for float, fine 140 x 280 mm 531 760 sponge rubber cover, fine-pore

Rubber plaster cup conical, made of soft PVC 531 745

Corner trowel stainless steel, for inside 063 247.004

Tools

Cutter with wooden handle 063 231.007

Steel sledge hammer 1,250 g, 362 335.002 with rubber handle

Plasterer’s hatchet with steel tube and rubber handle 064 072.003

Facade spattle 500 mm 362 362.004 350 mm, stainless steel, w. soft grip 531 714


Plasterer’s plane alu 500 mm long, 063 234.004 with 8 blades

132 133

1 22

MM 2599/10 GB MM 2599/10 GB

Dapling bars made of solid alu pipe 0.8 m 211 705.000 2.2 m 211 706.009 3.0 m 211 707.008

Levelling tripods with high feet for larger self levelling floor screed heights standard 12 cm 211 703.002 high 14 cm 211 704.001

“Swiss“ smoother stainless steel, screwed on handle painted red 500 x 135 mm 063 243.008

Smoothing and measuring floats, model SLN with 1 horizontal level, dimension: approx. 80 x 17 mm measuring acc.: 1 mm/m = 0,057° in normal position 100 cm 362 315.006 150 cm 362 316.005 200 cm 362 317.004 250 cm 362 318.003 300 cm 362 319.002

For self levelling floor screed layers

Floor-layer smoothing trowel handle painted red, with extra long alu fin 500 x 90 mm 362 308.000 600 x 90 mm 362 309.009 700 x 90 mm 362 310.001 280 x 130 x 0.7 mm 362 311.000

Screed layers‘ overall safety clothes with artificial leather trimmings, large knee padding; protection against dampness, zip is reinforced, perfect fit.

Size 48 362 347.003 Size 50 362 348.002 Size 52 362 349.001 Size 54 362 350.003 Size 56 362 351.002 Size 58 362 352.001 Size 60 362 373.006

Screed layers‘ working trousers safety clothes with artificial leather trimmings, large knee padding; protection against dampness, zip is reinforced, perfect fit.

Size 48 362 353.000 Size 50 362 354.009 Size 52 362 356.007 Size 54 362 357.006 Size 56 362 358.005 Size 58 362 359.004 Size 60 362 374.005

Tools

Knee protectors harmonica (Fig. 1) 362 344.006 box-form (Fig. 2) 362 343.007 made of polyurethane, CFC-free production, certified as per DIN EN 14404

Strap (without Fig.) 270 mm 362 345.005 410 mm 362 346.004

Self levelling floor screed shoe cover for working on fresh self levelling floor screed 362 360.006 Front belt 362 771.000 Rear belt 362 772.000

Protective helmet – yellow with PM-imprint 064 626.006

General


1 pair of spikes screed shoe for work on fresh screed 531 746

135134 135134MM 2599/10 GB MM 2599/10 GB

Putzmeister worldwide

PutzmeisterMörtelmaschinen GmbH

Max-Eyth-Str. 10 72631 Aichtal · Germany

Tel +49 (0) 7127 599-0Fax +49 (0) 7127 599-743

Hotline +49 (0) 7127 599-699

You can find your contact persons in Sales, Marketing, Customer Service and Spare Parts Management on our website:

www.mortarmachines.com

136 137MM 2599/10 GB MM 2599/10 GB

Putzmeister Mörtelmaschinen GmbH (Last revised January 2002)

I. Scope of Application1. The following terms and conditions apply to all deliveries and performances, regardless of whether the individual case is a sales contract or a contract for work and services or a contractual relationship of yet another nature.2. Terms and conditions of sale or other terms and conditions of business of the client do not apply, even if the supplier has not expressly objected to said terms and conditions.

II. Conclusion of Contract, Modifications of Contract, Assignment of Rights1. The documents which are a part of the offer (e.g., photographs, drawings) as well as data about the extent of the delivery, appearance, performance, dimensions, weight, consumption of operating materials, operating costs, etc., are only approximate values unless they have expressly been designated as binding. The supplier retains rights of ownership and copyrights to cost estimates, drawings and other documents. They must not be made available to third parties and shall be returned upon request. 2. The contract shall be deemed concluded when the supplier has confirmed acceptance of the order in writing or has commenced delivery or performance. If the supplier has submitted an offer which is subject to a time limit, the contract shall be deemed concluded when the client has submitted written acceptance of the offer in due time.3. Oral secondary agreements and amendments to the contract shall not become effective until the supplier has con firmed them in writing. Obvious spelling or calculation errors may be cor-rected retroactively.4. The client may not assign his rights from this contract.

III. Prices1. The prices are given ex works, including loading in the works, but excluding packaging, plus applicable value- added tax in conformity with the applicable provisions of the delivery or performance country. To the extent that binding remuneration of the supplier has not been agreed, the supplier’s prices in effect on the day of the delivery shall apply.2. Engineer work, installation and commissioning will be billed separately. The billing may be calculated at either a flat rate or according to actual expenditure, plus travel costs, subsistence allowance and overnight expenses, overtime, surcharges for Sundays and public holidays.3. Price changes are admissible if there has been a lapse of more than 6 months between conclusion of the contract and the agreed date of delivery. The supplier is entitled to adjust prices to the extent that the new price is in the same ratio to the agreed price as the price of the delivery and performance according to the valid price list on the day of the delivery is to the price of the delivery according to the valid price list on the day of the conclusion of the contract. With respect to other deliveries and performances not shown in a price list, the supplier is entitled to make a price adjustment which is reasonable in view of the circumstances. 4. If costs or charges are included in the prices and the former are raised following the conclusion of the contract, or if they become due additionally following conclusion of the contract, the supplier is entitled to bill the client for the additional amount.5. If at the request of the client the supplier is prepared to make an exchange, the supplier is entitled to bill the incurred costs, no less, however, than the amount of the loss in value resulting from aging and use, plus 10.0% of the agreed price of the originally agreed object of the delivery, as compensation for the expenditures incurred by the supplier due to the exchange. The supplier may not demand the flatrate cost compensation described in the above provision if the client proves that no, or only minor, damage or expenditure resulted for the supplier.

IV. Payment, Default of Payment, Set-Off, Retention1. In the absence of deviating agreements, payment for the delivery of machines shall become due within 7 days of the delivery, for spare parts within 30 days and for services within 14 days of the invoice date without deductions.2. Any and all outstanding receivables shall become due and payable immediately – even if an extension or other delay of payment has been granted – as soon as the client is more than 5 workdays in default of fulfilment, in whole or in part, of his obligations to the supplier or if circumstances arise which substantially reduce the creditworthiness of the client (e.g., deterioration of assets, suspension of payments, excess debt, objections to bills of exchange and cheques, filing of a petition for institution of bankruptcy proceedings or the institution or dismissal thereof). The supplier may in this case refuse further deliveries or performances and request the provision of reasonable security for his claims. 3. Payment by bill of exchange is subject to special agreement. Bills of exchange and cheques will only be accepted subject to redemption. The client shall bear collection and discount charges. No cash discount will be granted for payment by bill of exchange or in the event that there are overdue payments, even if such a discount has otherwise been agreed.4. The client may offset supplier’s claims solely against undisputed or non-appealable claims. The client has a right of retention only if his counterclaim is based on the same contractual relationship and is undisputed or non- appealable, or if the supplier has committed a gross violation of his obligations from the same contractual relationship. However, this provision is without prejudice for the right of the client to retain a reasonable part of the purchase price due to defects of the supplier’s performance.5. If the client is in default of payment, interest at a rate of 8.0% above the basic interest rate shall be paid on the supplier’s claims. This provision is without prejudice for the supplier’s claim for compensation for additional damage.6. If the client suffers deterioration of assets in the meaning of No. IV.2., the supplier may withdraw from the contract. This provision is without prejudice for further statutory claims of the supplier, e.g., damage compensation. Damage compensation claims of the client are ex-cluded.

V. Delivery Time, Partial Performances, Delay of Acceptance1. Delivery and installation periods do not commence until the supplier and the client have reached agreement on all details of the performance and all terms and conditions of the transaction and the supplier has confirmed the order. Said periods shall be suspended as long as the client is in default of fulfilment of his contributory obligations from this contract (e.g., provision of documents, supply of materials, permits, releases) or of an agreed advance payment.2. The delivery period shall be deemed as observed if the object of the delivery has left the works or if notification of readiness for shipping has been given before lapse of the period.3. The delivery period shall be extended by a reasonable amount in the event of force majeure, strike, lock-out and other unusual circumstances without fault; this provision shall also apply if a presupplier is affected, to the extent that these circumstances can be shown to have an influence on the delivery period.4. If the supplier’s performance is delayed, he shall nevertheless not be in default of performance to the extent that the delay is caused by circumstances which he could not foresee and prevent when taking reasonable precautions and which he could not overcome by taking reasonable measures.5. The supplier is entitled to withhold his performance as long as the client does not fulfil his obligations to the supplier from this or another contract or due to other legal reasons.6. Partial performance is admissible to the extent that it is reasonable for the client. Such partial performances shall be deemed independent legal transactions which may be bill separately.

7. If the terms and conditions of payment are not observed, if the delivery is not accepted in due time or if the acceptance thereof is refused or if security which has been agreed or is due in accordance with No. IV.2. has not been provided, the supplier is entitled, following fruitless lapse of a reasonable extension, to withdraw from the contract and to claim damage compensation. The supplier may claim without further proof damage compensation from the client in the amount of 25.0% of the order total for mass produced products and 75.0% of the order total for custom produced products, to the extent that the client does not prove that no dam-age, or only minor damage, has resulted. This provision is without prejudice for a claim of greater damage upon substantiation.8. If at the request of the client the dispatch is delayed, the supplier may bill either the storage and maintenance costs actually incurred or a flat rate in the amount of _% of the invoice amount per month; the latter is, however, not permitted if the client proves that the supplier suffered no, or only minor, damage or incurred no, or only minor, expenditures. This provision has no effect on the client’s payment obligations.

VI. Transfer of Risk, Shipping and Acceptance1. The risk shall pass to the client no later than the point in time of the dispatch of the object of the delivery. This provision shall also apply to partial performance, or if the supplier has agreed to bear the costs for shipping or installation, or if he performs the delivery himself. No liability is accepted for the most favourable freight charges or transport time.2. If the delivery, the shipping or the acceptance of the object of the delivery is delayed by the client due to no fault of the supplier, all risks – including the risk of deterioration or loss of the object of the delivery as well as all risks resulting from the object itself – shall pass to the cli-ent as of the notification of the readiness for shipping or notification of completion.3. Upon written request, the consignment will be insured at the client’s expense for the cover sum he requests.4. The client is liable for any and all damage which he causes by his negligence during or before acceptance of the object of the delivery (e.g., sampling, any acceptance procedure to be per-formed, etc.).5. Delivered objects shall be accepted by the client, even if they are defective, without prejudice for his rights.

VII. Complaint of Defects, Guarantee, Guarantee Period1. The client shall examine the object of the delivery immediately after receipt and lodge written complaint of any defects without delay. The client shall also examine the object of the delivery for defects before every commissioning, in particular regarding safety and suitability for use. During its use, the object of the delivery shall be moni tored constantly with regard to safety and defects. If there are even slight reservations concerning the suitability for use or the slightest reservations concerning safety, the object must not be used or its operation must be shut down immediately. The supplier shall be given written notification immediately, specifying the reservations or the defect within the scope of a complaint of defects. The client shall allow the supplier the time and opportunity required to perform any and all remedies and re-placement deliveries which the supplier regards as necessary. Otherwise, the supplier is released from liability for any consequences resulting therefrom. 2. If the supplier’s performance is defective at the time of the transfer of risk, the supplier shall perform subsequently, at his discretion remedying the defect or delivering a defect-free object in exchange for the defective object delivered. Replaced parts become the property of the supplier. If subsequent performance regarding a defect for which the supplier is responsible is not possible, has finally failed, is unreasonable for the purchaser, or if the seller has refused both types of subsequent performance, or if a reasonable extension for subsequent performance granted to the supplier has fruitlessly lapsed, the client may at his discretion reduce the remuneration for the supplier or withdraw from the contract. If there is only an minor defect, however, the client has only the right to reduce the remuneration. 3. If the supplier has fraudulently concealed a defect or given a guarantee for the quality of the object, the statutory regulation shall apply.4. Unauthorized remedy of defects by the client or third parties shall result in the loss of all claims due to defects on the supplier. The supplier will not bear the costs for the remedy of defects by the client or third parties without the express prior agreement of the supplier. This provision does not apply in urgent cases – especially when delay is not possible – in which the operating safety is endangered or in order to prevent unreasonably great damage. In such cases, the supplier shall be notified immediately and shall be obligated to reimburse only the necessary costs.5. In particular, the supplier does not accept any guarantee or any warranty obligation for damage in the following cases: unsuitable or improper use, defective installation or commis-sioning by the client or third parties, natural wear and tear, defective or negligent handling, im-proper maintenance, excessive load, unsuitable operating materials and replacement materi-als, poor work, unsuitable foundation, chemical, electro-technical/electronic or electric influences. This exclusion does not apply if the supplier is responsible for the damage in conformity with the more specific provision of the regulation in VIII. No. 5. There shall also be no liability and warranty obligation for the supplier in particular for the following measures and actions taken by the client or third parties and the consequences thereof: improper remedy of defects, change of the object of the delivery without the prior agreement of the supplier, addition and insertion of parts, in particular of spare parts which do not come from the supplier or which the supplier has not expressly approved for insertion, and failure to follow the operating instructions.6. The supplier does not grant any warranty for material provided by the client or acquired on the basis of specifica- tions predetermined by the client or for designs predetermined by the client.7. The supplier does not grant any warranty for possible material defects for the sale of used machines, devices or parts. The supplier does not guarantee any quality and points out that used machines and parts frequently do not have the same quality as newly manufactured machines and parts, also with respect to their ability to perform.8. The client’s claims for subsequent performance as well as his possible claims for damage compensation or reimbursement for expenditures due to defects shall be time-barred after one year following delivery of the goods for deliveries, after one year following conclusion of the installation for installations. If the acceptance of the object of the delivery or the accep-tance of the delivery and performance is delayed due to no fault of the supplier, the guarantee shall expire no later than 12 months after readiness. An analogous provision applies to subsequent performance. If the supplier has fraudulently concealed the defect or has given a guarantee for the quality of the item, the statutory regulation shall apply to the time-barring of any claims on the part of the client based thereon. The statutory regulation shall also apply to the time-barring of any damage compensation claims of the client because of defects if the supplier is guilty of intention or gross negligence or if the damage compensation claim is based on an injury to life, body or health.9. Any and all other further claims of the client are excluded, in particular for damage compensa-tion, including compensation for damage which did not result on the object of the delivery it-self. No. VIII.5. applies accordingly.

VIII. Withdrawal, Damage Compensation and Limitation of Actions1. The client may withdraw from the contract if the complete performance finally becomes impossible for the supplier before the transfer of risk. A claim by the client for damage com-pensation due to final impossibility of the performance is excluded unless the supplier is guilty of gross negligence. Any claim for damage compensation is limited to the damage foreseeable at the time of conclusion of the contract and resulting from the usual course of events and is limited in amount to a maximum of 15% of the contract sum. The client may also withdraw from the contract if, for an order of identical items, the delivery of a part of the ordered items in terms of quantity becomes impossible and the client has a justified interest in refusing a partial delivery. If this is not the case, the client may reduce the counter-performance accordingly.

Terms and Conditions of Sale and Delivery2. If the impossibility occurs during delay of acceptance or due to the fault of the client, the latter remains obligated to counterperformance.3. The client may withdraw from the contract if the supplier is in default of his performance, to the extent that said performance is due, the client has previously set a reasonable extension without success, and the supplier is responsible for his non-performance. A claim by the client for damage compensation due to the supplier’s default of performance is excluded unless the supplier is guilty of gross negligence. Any claim for damage compensation is limited to the damage foreseeable at the time of conclusion of the contract and resulting from the usual course of events and is limited in amount to _% for each full week of delay, in total to a maximum of 5% of the value of that part of the total delivery which cannot be used in due time because of the delay.4. The client’s right to withdraw from the contract – beyond the cases regulated above in Nos. 1 and 3 – in accordance with statutory regulations in the event of a violation of obligations for which the supplier is responsible and which does not result from a defect remains unaffected.5. Any and all other more extensive claims of the client, in particular for termination and for damage compensation, including claims for damage compensation in lieu of performance and claims for compensation of damage of any type, for any legal reason whatsoever, including the violation of pre-contractual and contractual obligations, for actions in tort committed during development, conclusion and performance of the contract as well as for damage which did not result on the object of the delivery itself, are excluded. This exclusion of liability does not apply if the supplier is guilty of gross negligence. Furthermore, this exclusion of liability does not apply in the event of culpable violation of the essential contractual obligations of the supplier. Furthermore, this exclusion of liability does not apply to any claim of the client for damage compensation based on an intentional or grossly negligent injury of life, body or health. Finally, this exclusion of liability does not apply in those cases in which liability is compulsory in accordance with the Product Liability Act for personal injury or material damage to privately used objects. If these cases result in the supplier’s liability – or in deviation from the above provisions in other cases due to contractual or statutory basis for claim – said liability shall be limited to compensation for the foreseeable damage resulting from the usual course of events and which has been proven in each individual instance. However, this limitation of liability does not apply to any liability in accordance with the Product Liability Act due to defects of the object of the delivery for personal injury or for material damage to privately used objects. Furthermore, this limitation of liability does not apply if the supplier is guilty of intention or of gross negligence.

6. Damage compensation claims of the client on the supplier – whether due to the violation of pre-contractual or con tractual obligations, to actions in tort committed during the develop-ment, conclusion and performance of the contract or due to other legal reasons – shall be time-barred no later than one year after the end of the year in which the claim arose and the client learned of the circumstances substantiating the claim and of the person of the debtor, or would have learned thereof without gross negligence. If the debtor is guilty of intention or gross negligence, the statutory regulation shall apply. Furthermore, the statutory regulation shall apply to any damage compensation claim based on an intentional or grossly negligent in-jury of life, body or health.7. The managing directors of the supplier and his employees are liable to the client for actions in tort committed during the development, conclusion and performance of the contract only in cases of intention and gross negligence. No. 6 above applies analogously to the time-barring of claims of the client on the managing directors of the supplier and his employees.

IX. Security1. The object of the delivery remains the property of the supplier until full payment of the agreed price and of all other claims, including future claims, from the business relationship with the client. If in the context of the payment of the purchase price the supplier becomes liable on the basis of bills of exchange, the retention of title does not l lapse before all bills of exchange have been completely redeemed by the client.2. The client assigns now to the supplier the claims arising from the further sale of the objects of the delivery in the amount of the value of the objects of the delivery and all secondary rights. The client is authorized to collect the claim. The authority of the supplier to collect the claim himself remains unaffected hereby.3. The supplier obligates himself to release security at his discretion to the extent that the realizable value of his security exceeds the total of his claims from the business relationship by more than 10%.4. As long as the client fulfils his obligations to the supplier, he is entitled to dispose of the object of the delivery in the course of orderly business and subject to retention of title, to the extent that the claims effectively pass to the supplier in accordance with No. 2. Extraordinary dis-posals such as pledges, transfer by way of security and any and every assignment are not permissible. The supplier shall be given written notification immediately of any attachment by third parties on the object of the delivery or assigned claims, in particular pledges.5. During the period of the retention of title, the client is in principle entitled to possess and make use as intended of the object of the delivery. In the event of actions in breach of contract by the client – in particular if the client is in default of payment – as well as in the cases of No. IV.2., however, the supplier may repossess the object of the delivery and revoke the authori-zation to collection of the claims resulting from the further sale. The client is – under exclusion of rights of retention – obligated to surrender the object. The client shall bear any and all costs of the repossession and exploitation. The supplier is entitled to private sale. The client shall upon request immediately submit to the supplier a catalogue of the claims assigned in conformity with No. 2. as well as all additional information and documents necessary for exercise of the claims to which the supplier is entitled, and inform the debtors of the assignment.6. The client shall maintain the object of the delivery in proper condition during the retention of title and allow the supplier or a workshop authorized by the supplier – with the exception of emergencies – to perform immediately all of the maintenance and repair work prescribed by the supplier.7. In the case of automobile concrete pumps, the supplier shall have the right to possess the vehicle title for the duration of the retention of title.8. The exercise of the retention of title and pledge of the object of the delivery by the supplier shall not be deemed withdrawal from the contract.9. If the retention of title or the assignment is not effective according to the law of the country in which the goods are located, the security closest in nature to retention of title or assign-ment in this country shall be deemed as agreed. If a contribution of the client is required for this purpose, the client shall perform all legal actions necessary to establish and preserve such rights.

X. Industrial Property RightsIf the supplier is to perform according to drawings or models, samples, or using parts supplied by the client, the client shall warrant that industrial property rights of third parties are not infringed hereby. The client shall indemnify the supplier from any and all claims by third parties due to infringement of industrial property rights and shall compensate the supplier for any resulting damage and for his costs and expenditures. If the client is prohibited from manufacture or delivery by a third party on the basis of an industrial property right, the supplier is entitled to cease work without making a closer examination of the legal situation. In this case, the supplier may withdraw from the contract and demand compensation for his damage as well as his costs and expenditures.

XI. Use of SoftwareTo the extent that software is included in the scope of the delivery, the client shall be granted a non-exclusive right to use the supplied software, including its documentation. It is released for use on the object of the delivery intended for this purpose. The use of the software on more than one system is prohibited.

The client may reproduce, rework or translate the software or convert from the object code into the source code only within the legally permissible scope (Sec. 69 a ff UrhG, Copyright Act). The client obligates himself not to remove manufacturer’s information – in particular copyright notices – or to change them without the prior express permission of the supplier.

All other rights to the software and the documentation, including the copies, remains with the supplier or the software supplier. The granting of sub-licenses is not permissible.

XII. Proper Law, Place of Performance, Jurisdiction1. Sole proper law is that of the Federal Republic of Germany. In case of doubt, the German language version of all contractual provisions shall be decisive. The Uniform Sales Convention does not apply.2. Place of performance is 72631 Aichtal.3. If the client is a merchant, a legal person under public law or a special fund under public law, the courts of Stuttgart shall have jurisdiction for any and all disputes arising under this con-tractual relationship, including disputes regarding its creation and its effectiveness as well as for bill of exchange and cheque litigation. The supplier may apply to any other court which has jurisdiction according to statutory provisions.4. If one of the provisions of these terms and conditions of sale and delivery is invalid, in whole or in part, the validity of the remaining provisions shall not be affected.

Putzmeister Mörtelmaschinen GmbHD-72629 Aichtal – P.O. Box 2152 · GermanyTelephone: +49 (0) 71 27 599-0 - Fax: +49 (0) 71 27 599-520Internet: www.mortarmachines.com - E-mail: [email protected]

138MM 2599/10 GB

Notes

Date post:	13-May-2018
Category:	Documents
Upload:	duongtuyen
View:	270 times
Download:	11 times

Putzmeister Mörtelmaschinen GmbH Catalogue 201 … Mörtelmaschinen GmbH Catalogue 201 0/ 2011 ......

Documents