+ All Categories
Home > Documents > Quick Start Guide LED On button In-LineLinc Models: 2475SDB · Le present appareil est conforme aux...

Quick Start Guide LED On button In-LineLinc Models: 2475SDB · Le present appareil est conforme aux...

Date post: 31-Jul-2020
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
1
Rev. 7/16/2012 12:34 PM / See Owner’s Manual for Warranty Information, Patented © Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845 *If the controller does not have a beeper, wait until its LED begins blinking **Most products Quick Start Guide In-LineLinc Relay (Dual-Band) Models: 2475SDB Installation Note: Installation should be performed only by a qualified electrician or a homeowner who is familiar and comfortable with electrical circuitry. If you have any questions regarding installation, consult an electrician or call the INSTEON Support Line at 800-762-7845. 1) Be sure to write down the INSTEON I.D. and location of the fixture you'll be controlling (e.g., 01.F7.G5, Upstairs Bathroom Fan) 2) Turn off circuit breaker supplying power to the fixture 3) Disconnect the wires from the fixture you will be controlling and ensure that you have ½” of bare wire on the ends 4) See Figure 1 to identify and connect the line, load, neutral and ground wires on In-LineLinc. Be sure you have correctly identified the wires in the junction box before connecting them. 5) After you have connected all the wires, ensure that the wire connectors are firmly attached and that there is no exposed copper except for the ground wire 6) Prior to reinstalling the fixture, turn on circuit breaker supplying power to the fixture 7) Use the on/off buttons to test that the module is working and controlling the load 8) Add In-LineLinc to a scene as a responder: Use the On and Off button on In-LineLinc to set the load to the state you wish to activate from the controller (turn it on if you wish it to be on when the controller activates the scene, etc.). Press and hold the scene controller button until it beeps. * Controller LED will blink Press and hold In-LineLinc's Set button until it double-beeps In-LineLinc status LED will flash once and then turn on steady. Controller will double-beep** and its LED will stop blinking Confirm that scene addition was successful by tapping On then Off on the controller's scene button The load connected to the In-LineLinc will respond appropriately 9) Gently place In-LineLinc into the junction box, making sure that nothing could accidentally press any of the buttons on its face 10) Reinstall the fixture Status LED On button Off button Set button Figure 1 Owner’s Manual and Tech Support Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support Call: INSTEON Support Line at 800-762-7845 This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.
Transcript
Page 1: Quick Start Guide LED On button In-LineLinc Models: 2475SDB · Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

Rev. 7/16/2012 12:34 PM / See Owner’s Manual for Warranty Information, Patented © Copyright 2012, INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845

*If the controller does not have a beeper, wait until its LED begins blinking **Most products

Quick Start Guide In-LineLinc™ Relay (Dual-Band) Models: 2475SDB Installation Note: Installation should be performed only by a qualified electrician or a homeowner who is familiar and comfortable with electrical circuitry. If you have any questions regarding installation, consult an electrician or call the INSTEON Support Line at 800-762-7845. 1) Be sure to write down the INSTEON I.D. and location of the fixture

you'll be controlling (e.g., 01.F7.G5, Upstairs Bathroom Fan) 2) Turn off circuit breaker supplying power to the fixture 3) Disconnect the wires from the fixture you will be controlling and

ensure that you have ½” of bare wire on the ends 4) See Figure 1 to identify and connect the line, load, neutral and ground

wires on In-LineLinc. Be sure you have correctly identified the wires in the junction box before connecting them.

5) After you have connected all the wires, ensure that the wire connectors are firmly attached and that there is no exposed copper except for the ground wire

6) Prior to reinstalling the fixture, turn on circuit breaker supplying power to the fixture

7) Use the on/off buttons to test that the module is working and controlling the load

8) Add In-LineLinc to a scene as a responder: Use the On and Off button on In-LineLinc to set the load to the state you wish to activate from the controller (turn it on if you wish it to be on when the controller activates the scene, etc.). Press and hold the scene controller button until it beeps.*

Controller LED will blink Press and hold In-LineLinc's Set button until it double-beeps

In-LineLinc status LED will flash once and then turn on steady. Controller will double-beep** and its LED will stop blinking

Confirm that scene addition was successful by tapping On then Off on the controller's scene button

The load connected to the In-LineLinc will respond appropriately

9) Gently place In-LineLinc into the junction box, making sure that nothing could accidentally press any of the buttons on its face

10) Reinstall the fixture

Status LED On button

Off button Set button

Figure 1

Owner’s Manual and Tech Support Owner’s Manual and current Quick Start Guide: http://www.insteon.com/support Call: INSTEON Support Line at 800-762-7845

This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

Recommended