© 2019 Alamo Group, Inc.
ALAMO INDUSTRIAL1502 E. WalnutSeguin, Texas 78155830-372-9595
An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy before operating the equipment.
Rev 02-19 Part No. RRM0020
PARTS MANUAL
SYMBOL LEGEND AND CONVERSIONSTorque values for bolts without special indication in theparts catalog:
M5 = 5 Nm = 44 IN-LBM6 = 10 Nm = 88 IN-LBM8 = 23 Nm = 17 FT-LBM10 = 45 Nm = 33 FT-LBM12 = 76 Nm = 56 FT-LBM14 = 120 Nm = 89 FT-LBM16 = 168 Nm = 124 FT-LB
BOLT TORQUEMounting procedures for mowers will require a significant amount of bolt nut and washer installation.
Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness.
Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart.
Bolt tightness should be completed with and checked with a suitable torque wrench.
Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual.
Loose bolts on a frame or in a casting may be a result of: ● Vibration from the mower due to imbalance of the mower blades ● Pulled threads due to over tightening ● Distortion of the hole due to under tightening during installation
Bolts broken or sheared in the mounting structure or tractor may be the result of: ● Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating
surface ● Distortion of the bolt due to over-tightening ● Under tightening of the bolts
Check the bolt torque during installation and prior to delivery with a suitable torque wrench.
TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recog-nizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
CHANGE PAGES
Change Pages - 5
Date of Change Page Number04-03-2013 (EXAMPLE ONLY: ECN##### - chg pages 17, 23, 137)03-31-2016 document release date05-18-2016 replaced most images and updated most boms. all pgs.06-14-2017 replaced most images and updated most boms. all pgs03-21-2018 chg pgs 19, 2410-08-2018 replaced most images and updated most boms. all pgs.02-04-2019 updated cutter drive
CHANGE PAGES
Change Pages - 6
The following is a listing of pages that have been changed since the latest publication date for the overall document.
Parts Section – 2
For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to:
The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
Note: Please refer to The Safety Section in the front of this Manual for the proper part number when ordering replacement safety decals.
PARTS ORDERING GUIDE
ALAMO INDUSTRIAL1502 E. WalnutSeguin, Texas 78155830-379-1480
©2019 Alamo Group Inc.
PART NAME INDEX
CHASSIS........................................................................................................................................................................................................ 4
MAIN FRAME............................................................................................................................................................................................... 6
MOWER DECK (PART 1)............................................................................................................................................................................ 8
MOWER DECK (PART 2).......................................................................................................................................................................... 10
CUTTER DRIVE (PART 1)........................................................................................................................................................................ 12
CUTTER DRIVE (PART 2)........................................................................................................................................................................ 14
ENGINE CARRIER (PART 1).................................................................................................................................................................... 16
ENGINE CARRIER (PART 2).................................................................................................................................................................... 18
ENGINE CARRIER (PART 3).................................................................................................................................................................... 20
REMOTE CONTROL, ACCESSORIES..................................................................................................................................................... 22
ELECTRICAL SYSTEM (PART 1)............................................................................................................................................................ 23
ELECTRICAL SYSTEM (PART 2)............................................................................................................................................................ 25
©2019 Alamo Group Inc. Parts Section -3
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CHASSIS
ITEM PART NO. QTY. DESCRIPTION1 RR00665 36 LOCKING NUT ELASTIC STOP
2 RR00782 72 WASHER
3 RR105555 4 SPROCKET DISC
4 RR104972 20 PLASTIC ROLLER
5 RR104969 20 DISTANCE PIPE
6 RR104971 2 HUB
7 RR24613 36 HEX. SCREW
©2019 Alamo Group Inc. Parts Section -4
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CHASSIS
Continued...
ITEM PART NO. QTY. DESCRIPTION8 RR77312 2 WASHER
9 RR00026 2 HEX. SCREW
11 RR105534 8 HUB CAP
12 RR01349 8 SNAP RING
13 RR18405 16 BALL BEARING
14 RR104967 8 GUIDE WHEEL
15 RR106815 4 RING, SEALING, NILOS
16 RR107521 4 WAVE WASHER
17 RR105540 2 CHAINS TENSIONING ADJUSTER
18 RR105354 16 HOLE PLUG
19 RR105537 32 CATERPILLAR SUPPORT
20 RR00146 16 HEX. SCREW
21 RR00785 16 WASHER
22 RR00667 16 LOCKING NUT ELASTIC STOP
23 RR106742 32 HUB CAP
24 RR0106423 16 SNAP RING
25 RR106778 6 NILOS RING
26 RR13535 16 BALL BEARING, ROLLER, CHASIS
27 RR105362 4 ROLLER
28 RR104062 2 TAPERED WASHER
29 RR105064 8 CUP SPRING
30 RR00604 16 HEXAGON NUT
31 RR104961 8 CRAWLER TRACK
©2019 Alamo Group Inc. Parts Section -5
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MAIN FRAME
©2019 Alamo Group Inc. Parts Section -6
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MAIN FRAME
Continued...
ITEM PART NO. QTY. DESCRIPTION1 RR105071 4 BALL HEAD
2 RR105414 2 GAS-PRESSURIZED SPRING
3 RR105547 2 STRUT
4 RR104082 4 HEADED BOLT
5 RR105546 1 VERTICAL ADJUSTMENT
6 RR104083 8 WASHER
7 RR01453 8 COTTER PIN
8 RR105545 1 LEVER RIGHT
9 RR105539 1 ADJUSTING LEVER
10 RR28210 2 SPRING COTTER PIN
11 RR00784 2 WASHER
12 RR105210 1 LINEAR ACTUATOR CUTTING HEIGHT
13 RR79325 2 COLLAR BOLT
15 RR00736 4 EYE NUT
16 RR104075 2 HEX. SCREW
17 RR77312 8 WASHER
18 RR00026 2 HEX. SCREW
19 RR105541 1 MAIN FRAME
20 RR00787 12 WASHER
21 RR00785 12 WASHER
22 RR00667 6 LOCKING NUT ELASTIC STOP
23 RR104939 2 ELEKTRIC MOTOR
23a RR105821 1 BRUSH HOLDER
23b RR105471 4 TERMINAL SCREW
23c RR104076 8 HEXAGON NUT
23d RR17374 4 LOCK WASHER
23e RR55208 4 NUT CAP
23.1 RR105392 2 COVER ELECTRIC MOTOR
24 RR58109 2 PARALLEL KEY
25 RR105828 2 COUPLING SLEEVE
26 RR105941 2 GASKET
27 RR104941 2 GEAR
28 RR00009 8 HEX. SCREW
29 RR104080 2 PARALLEL KEY
30 RR104079 8 HEX. SCREW
31 RR16471 8 LOCK WASHER
1.1 RR16471 2 LOCK WASHER
1.2 RR00597 2 HEXAGON NUT
12a RR105212 1 LINEAR ACTUATOR, CABLE LOCK
27B RR106764 2 HEX. SCREW
27A RR106400 2 LOCK WASHER
©2019 Alamo Group Inc. Parts Section -7
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MOWER DECK (PART 1)
©2019 Alamo Group Inc. Parts Section -8
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MOWER DECK (PART 1)
Continued...
ITEM PART NO. QTY. DESCRIPTION1 RR952415 1 FUEL HOSE
2 RR23107 6 HOSE CLAMP
3 RR104948 2 CANISTER CONNECT
3 a RR105829 2 GASKET CANISTER CONNECT
6 RR00665 32 LOCKING NUT ELASTIC STOP
7 RR66413 2 WASHER
8 RR104055 2 OVAL-HEAD SOCKED SCREW
9 RR105504 2 CANISTER SAFEGUARD
10 RR104136 2 GAS CAN, W/DECALS
11 RR104139 1 COVER, LH
11 a RR950305 3 EDGE PROTECTIVE STRIP
11.1 RR75956 3 BASE CELLULAR RUBBER
12 RR00102 16 HEXAGON SCREW
13 RR77308 18 WASHER
14 RR00102 2 HEXAGON SCREW
16 RR104157 1 STRAP BATTERY
17 RR105493 1 BATTERY
17 a RR28162 1 HOOD
17 b RR75956 2 BASE CELLULAR RUBBER
18 RR12013 3 LOCKING NUT ELASTIC STOP
19 RR00780 3 WASHER
20 RR105557 1 PLC-HOLDER
21 RR79691 1 CUP SQUARE BOLT
22 RR00108 2 HEXAGON SCREW
23 RR12013 2 LOCKING NUT ELASTIC STOP
24 RR106904 1 PLC CONTROL
25 RR75929 2 SUPPORT FUSE WITH WIRE
26 RR77379 1 STARTER RELAY
27 RR00765 2 CUP SQUARE BOLT
28 RR105057 1 DIODE
29 RR00126 2 HEX. SCREW
30 RR77306 6 WASHER
30.1 RR106823 4 PLASTIC SHIM
31 RR105522 1 WIRE SET RELAY BOX
32 RR103249 1 CAPACITOR
33 RR105542 1 RADIO CONTROL UNIT
33a RR106178 4 RECEIVER RADIO CONTROL UNIT
33.1 RR106857 2 BASE CELLULAR RUBBER
34 RR00142 1 HEXAGON SCREW
35 RR104138 1 SUPPORT, FLAP
©2019 Alamo Group Inc. Parts Section -9
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MOWER DECK (PART 2)
©2019 Alamo Group Inc. Parts Section -10
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
MOWER DECK (PART 2)
Continued...
ITEM PART NO. QTY. DESCRIPTION38 RR00782 26 WASHER
39 RR16521 30 CUP SQUARE BOLT
40 RR105559 4 AXLE BEARING
41 RR105069 32 NYLON WASHER
42 RR105554 22 PROTECTIVE FLAP
43 RR104957 88 BEARING BUSH
44 RR77310 4 LOCKWASHER
45 RR00113 4 HEXAGON SCREW
46 RR104958 2 HINGED BEARING AXLE
47 RR105093 1 FLANGE PLATE
48 RR104140 1 COVER, RH
48.1 RR75956 3 BASE CELLULAR RUBBER
48 a RR950305 1 EDGE PROTECTIVE STRIP
49 RR78862 1 WRENCH
50 RR105501 1 SPECIAL WRENCH
51 RR104091 2 KNURLED NUT
51 a RR00754 2 CUP SQUARE BOLT
52 RR105838 2 PLUG
©2019 Alamo Group Inc. Parts Section -11
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CUTTER DRIVE (PART 1)
©2019 Alamo Group Inc. Parts Section -12
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CUTTER DRIVE (PART 1)
Continued...
ITEM PART NO. QTY. DESCRIPTION1 RR104073 4 HEXAGON NUT
2 RR104062 4 TAPERED WASHER
3 RR100522 2 CLAMPING BUSH
4 RR105022 2 PULLEY
5 RR104933 1 V-BELT CUTTER DRIVE
6 RR00790 4 WASHER
7 RR68671 4 BALL BEARING
8 RR00666 9 LOCKING NUT ELASTIC STOP
9 RR00784 8 WASHER
10 RR104996 2 FLANGED HOUSING
11 RR01846 2 PARALLEL KEY
12 RR104987 2 BLADE SHAFT
15 RR00784 8 WASHER
16 RR00116 8 HEX SCREW, M10 X 35MM
17 RR104998 2 COVER
18 RR105391 4 SPACER NUT
19 RR100850 4 BLADE TOP
20 RR104956 2 BLADE SUPPORT
20a RR105023 4 BLADE SUPPORT CPL BLADE
21 RR100166 4 BLADE DOWN
22 RR100495 4 DISTANCE RING
23 RR00253 4 HEX. SOCKET SCREW 10.9
24 RR104053 4 CAP NUT
25 RR19512 8 LOCK WASHER
26 RR00115 4 HEXAGON SCREW
27 RR01330 1 SNAP RING
28 RR01382 1 SNAP RING
29 RR15773 1 BALL BEARING
30 RR104974 1 IDLER PULLEY
31 RR76648 1 WASHER, M10 5X30 4
32 RR104994 1 BELT TENSIONER
33 RR00762 1 CUP SQUARE BOLT
34 RR00598 2 HEXAGON NUT
35 RR00785 1 WASHER
36 RR66692 2 WEDGE PLATE
37 RR77312 1 WASHER
©2019 Alamo Group Inc. Parts Section -13
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CUTTER DRIVE (PART 1)
©2019 Alamo Group Inc. Parts Section -12
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
CUTTER DRIVE (PART 2)
Continued...
ITEM PART NO. QTY. DESCRIPTION38 RR453177 1 HEXAGON SCREW
39 RR105024 1 LOCK WASHER
40 RR100501 1 PARALLEL KEY
41 RR104942 1 ELECTROMAGNETIC CLUTCH
41a RR104093 1 PIN HOUSING
41b RR104094 2 SEAL
41c RR104095 2 CONNECTOR SOCKET
41d RR952802 1 INSULATING HOSE (5cm)
51 RR77308 2 WASHER
52 RR00109 2 HEXAGON SCREW
©2019 Alamo Group Inc. Parts Section -15
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 1)
©2019 Alamo Group Inc. Parts Section -16
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 1)
Continued...
ITEM PART NO. QTY. DESCRIPTION1 RR104962 1 ENGINE, GAS, 4-STROKE
2 RR105027 1 DRAIN HOSE
3 RR105028 1 CONNECTION PIECE DRAIN HOSE
4 RR23107 1 HOSE CLAMP
5 RR104960 1 GENERATOR
5 a RR105822 1 BRUSH HOLDER
5 b RR17374 2 LOCK WASHER
5 c RR55208 2 NUT CAP
5.1 RR104076 4 HEXAGON NUT
6 RR00666 4 LOCKING NUT ELASTIC STOP
7 RR00784 2 WASHER
8 RR105548 1 FLANGE PLATE GENERATOR
9 RR00147 2 HEXAGON SCREW
10 RR105352 1 RELAY OPERATING CIRCUIT
10 a RR00595 2 HEXAGON NUT
10 b RR55208 2 NUT CAP
11 RR00779 2 WASHER
12 RR28105 2 LOCKING NUT
13 RR00595 2 HEXAGON NUT
14 RR00782 14 WASHER
15 RR79727 2 HEXAGON SCREW 8.8
16 RR105562 1 ENGINE CARRIER
17 RR00764 2 CUP SQUARE BOLT
18 RR104977 1 V-BELT
19 RR104986 1 V-BELT PULLEY
20 RR105358 1 DISTANCE BUSH
21 RR104966 1 CLAMPING BUSH
22 RR79652 1 WASHER
23 RR453177 1 HEXAGON SCREW
24 RR58109 1 PARALLEL KEY
25 RR105360 1 DISTANCE BUSH
26 RR104090 1 PARALLEL KEY
27 RR105065 1 CLAMPING BUSH
28 RR105359 1 DISTANCE BUSH
29 RR101218 1 V-BELT PULLEY
30 RR00006 4 HEXAGON SCREW
31 RR77308 8 WASHER
32 RR00109 8 HEXAGON SCREW
33 RR104063 4 HEXAGON SCREW
©2019 Alamo Group Inc. Parts Section -17
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 2)
©2019 Alamo Group Inc. Parts Section -18
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 2)
Continued...
ITEM PART NO. QTY. DESCRIPTION34 RR77310 4 LOCKWASHER
35 RR104973 1 MUFFLER
35 a RR410391 2 GASKET MUFFLER
36 RR105549 1 ENGINE GUARD
37 RR00108 8 HEXAGON SCREW
38 RR77306 8 WASHER
39 RR00665 9 LOCKING NUT ELASTIC STOP
41 RR105401 1 SUPPORTING STRAP LH
42 RR105403 1 FASTENING STRAP LH
43 RR105404 1 FASTENING STRAP RH
44 RR105402 1 SUPPORTING STRAP RH
45 RR105832 1 ANTENNA KIT EXTERNAL
46 RR105406 1 ROTATING BEACON
47 RR105202 1 EMERGENCY STOP SIGN
48 RR105206 1 EMERGENCY STOP SWITCH
51 RR105207 1 SIGNAL LIGHT
52 RR105502 2 HOOP GUARD
53 RR105218 1 ROCKER SWITCH
54 RR104137 1 HOOD
54a RR950305 1 EDGE PROTECTIVE STRIP
55 RR00779 4 WASHER
56 RR00147 4 HEXAGON SCREW
57 RR105361 2 RELAY CHANGEOVER CONTACT
58 RR79651 4 WASHER
59 RR00102 4 HEXAGON SCREW
60 RR00150 12 HEXAGON SCREW
60a RR55208 12 NUT CAP
61 RR17374 12 LOCK WASHER
62 RR104955 2 CAPACITY FUSE
63 RR00003 8 HEXAGON SCREW
64 RR00780 8 WASHER
65 RR104934 2 ORDER RR104934-R OR RR104934-L
66 RR104993 1 THERMAL PAD
67 RR105560 1 GENERATOR GUARD
68 RR105029 4 PLASTIC NUT
69 RR105208 4 SCREW CONNECT. CORR. PIPE
70 RR00109 1 HEXAGON SCREW
71 RR77310 4 LOCKWASHER
©2019 Alamo Group Inc. Parts Section -19
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 3)
©2019 Alamo Group Inc. Parts Section -20
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ENGINE CARRIER (PART 3)
Continued...
ITEM PART NO. QTY. DESCRIPTION72 RR00113 4 HEXAGON SCREW
73 RR105569 1 LINEAR ACTUATOR THROTTLE
74 RR00318 4 OVAL-HEAD SCREW
75 RR28104 4 LOCKING NUT
76 RR105558 1 THROTTLE LEVER
77 RR105835 1 CABLE CLAMP
78 RR105351 1 CABLE THROTTLE
79 RR104991 1 DISSIPATOR
80 RR104992 1 DISSIPATOR SUPPORT
81 RR12013 8 LOCKING NUT ELASTIC STOP
82 RR73667 1 HEX SCREW, M10X12
83 RR77310 2 LOCKWASHER
84 RR105416 1 CLAMP
©2019 Alamo Group Inc. Parts Section -21
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
REMOTE CONTROL, ACCESSORIES
ITEM PART NO. QTY. DESCRIPTION1 RR105830 1 WAIST CARRYING STRAP
2 RR105831 1 NECK CARRYING STRAP
3 RR105832 1 ANTENNA KIT EXTERNAL
4 RR105469 1 BATTERY REMOTE CONTROL
5 RR105833 1 BATTERY CHARGER 12-24V DC
----- ----- - PLUG CIGARETTE LIGHTER
6 RR105834 1 BATTERY CHARGER 90-264V AC
7 RR104128 1 SPARE KEY REMOTE CONTROL
©2019 Alamo Group Inc. Parts Section -22
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ELECTRICAL SYSTEM (PART 1)
©2019 Alamo Group Inc. Parts Section -23
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ELECTRICAL SYSTEM (PART 1)
Continued...
ITEM PART NO. QTY. DESCRIPTION1 RR410393 1 REGULATOR, VOLTAGE
2 RR41035 1 ELECTRIC STARTER
2.1 RR105530 1 STARTER CABLE BLACK/RED
3 RR77379 1 STARTER RELAY
4 RR105493 1 BATTERY
4.1 RR105528 1 BATTERY CABLE BLACK
4.2 RR105529 1 BATTERY CABLE RED
5 RR105569 1 LINEAR ACTUATOR THROTTLE
6 RR105210 1 LINEAR ACTUATOR CUTTING HEIGHT
6.1 RR105570 1 CABLE LIN. ACT. CUTTING HEIGHT
6a RR105212 1 LINEAR ACTUATOR, CABLE LOCK
7 RR105521 1 WIRE SET12 V
8 RR105522 1 WIRE SET RELAY BOX
9 RR105520 1 WIRE SET CANBUS
10 RR105531 1 WIRE SET HOOD
11 RR104934 2 ORDER RR104934-R OR RR104934-L
12 RR104939 2 ELEKTRIC MOTOR
12.1 RR104143 4 CABLE, 25mm - 1000mm
13 RR104960 1 GENERATOR
13.1 RR105525 1 CABLE
13.2 RR105523 1 CABLE
13.3 RR105527 1 CABLE
13.4 RR104144 2 CABLE, 25mm - 380mm
14 RR105352 1 RELAY OPERATING CIRCUIT
15 RR105832 1 ANTENNA KIT EXTERNAL
16 RR105542 1 RADIO CONTROL UNIT
16a RR106718 1 RECEIVER RADIO CONTROL UNIT
17 RR105206 1 EMERGENCY STOP SWITCH
17a RR105202 1 EMERGENCY STOP SIGN
18 RR105207 1 SIGNAL LIGHT
19 RR105218 1 ROCKER SWITCH
20 RR105213 1 PLC CONTROL
21 ----- 1 RELAY BOX
21.1 RR103553 8 RELAY
22 RR105361 2 RELAY CHANGEOVER CONTACT
22.1 RR104145 4 CABLE, 6mm - 200mm
23 RR104942 1 ELECTROMAGNETIC CLUTCH
23a RR104093 1 PIN HOUSING
23b RR104094 2 SEAL
23c RR104095 2 CONNECTOR SOCKET
©2019 Alamo Group Inc. Parts Section -24
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ELECTRICAL SYSTEM (PART 2)
©2019 Alamo Group Inc. Parts Section -25
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
ELECTRICAL SYSTEM (PART 2)
Continued...
ITEM PART NO. QTY. DESCRIPTION23d RR952802 - .05 M INSULATING HOSE
24 ----- 1 AMP-SUPERSEAL-CONNECTER 2-POLE
25 ----- 2 AMP-SUPERSEAL-CONNECTER 3-POLE
26 ---- 2 AMP-SUPERSEAL-CONNECTER 5-POLE
27 ----- 2 AMP-SUPERSEAL-CONNECTER 6-POLE
28 RR103249 1 CAPACITOR
----- RR55541 20 CABLE TIE
29 RR75928 1 FLAT FUSE, 15A
30 RR76014 1 FLAT FUSE, 5A
31 ---- 1 ELECTRIC PLUG, 12V/5A
32 RR105406 1 ROTATING BEACON
----- RR105417 10 CABLE TIE
©2019 Alamo Group Inc. Parts Section -26
RRM0020 - Ridge Runner Parts Manual Pub 3-16 Rev 02-19
TO THE OWNER/OPERATOR/DEALERTo keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators:
REQUIRED OF THE OWNER
1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard.2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C.3. Ensure that each employee uses such seat belt while the tractor is moving.4. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the
protected area provided by the ROPS.
REQUIRED OF THE OPERATOR
1. Securely fasten seat belt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going, especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly, no jerky turns, starts, or stops.8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machin-ery guards in place...
Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
ALAMO INDUSTRIALLimited Warranty
ALAMO INDUSTRIAL1502 E. WalnutSeguin, Texas 78155830-379-1480
1. Limited Warranties1.01. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser
(“purchaser”) and warrants for six months to the original commercial or industrial purchaser (“purchaser”) that the goods purchased are free from defects in material or workmanship.
1.02. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.
1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your operator’s manual.
1.04. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf of manufacturer.
2. Remedies And Procedures2.01. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of
purchase.2.02. Purchaser claims must be made in writing to the authorized dealer (“dealer”) from whom purchaser purchased the goods or an approved
authorized dealer (“dealer”) within 30 days after purchaser learns of the facts on which the claim is based.2.03. Purchaser is responsible for returning the goods in question to the dealer.2.04. If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to
defects in material or workmanship, manufacturer will: (A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser
paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer.
2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory.
3. Limitation Of Liability3.01. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not
limited to, merchantability and fitness for a particular purpose.3.02. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods.3.03. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect
to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer’s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods.
3.04. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2) years after the cause of action has occurred.
4. Miscellaneous4.01. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas.4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be
a waiver of any other term.4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such
provision shall not invalidate any other provisions herein.4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
Keep for your records
Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty.
Alamo Industrial Implement Model ____________________________ Serial Number ________________________________Date Purchased __________________________________________ Dealer ______________________________________
Attention:Read your operator’s manual
Ridge Runner Parts Manual (PUB 03-16) P/N RRM0020
1502 E. Walnut St.Seguin, Texas 78155
Sales and MarketingTel 800.882.5762 Fax 830.379.0864
Warranty Registration/Claims
Return AuthorizationsOnline Part Orders
Techical Informationwww.alamoparts.com
Tel 800.356.6286 Fax 800.322.5141www.alamo-industrial.com
www.alamoparts.com