Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 1 of 12
Test Room ID: R11M
Description:
ANECHOIC ABSORBER‐LINED UNIVERSAL TEST ENCLOSURE
Primary Testing Uses:
MIL‐STD, CISPR, CE MARK, DO‐160
Dimensions:
Outside 5.8m x 6.1m x 4.2m (19ft. x 20ft. x 14ft) Inside/Usable 5.18m x 5.48m x 3.96m (17ft. x 18ft. x 13ft.) [See Figure – 5 below]
Construction:
Galvanized Steel Ferrite tiles placed on all four walls and the ceiling. RF absorber placed on all four walls and the ceiling. Ground Plane Bonding: Brass Brackets
Ground Plane Dimensions:
4.88m x 1.88m x 0.78mm (16ft. x 6ft. x 0.031in.); Removable [see Figure – 5 below]
Distance from Cable Tunnel to Front of Ground Plane:
2.16m (85in.)
Room Filters:
(2) 30A DC Filtered Lines (2) 50A DC Filtered Lines
Power Availability:
115VAC, 400Hz, 3Phase, 30A Filtered AC Power 115VAC, 60Hz, 3Phase, 50A Filtered AC Power 115VAC, 60Hz, 1Phase, 20A Outlets Note: Other power arrangements are available upon request.
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 2 of 12
Monitor Room ID: R11P
Description:
MONITOR ENCLOSURE
Dimensions:
4.88m x 2.44m x 3.05m (16ft x 8ft x 10ft) [see Figure – 5 below]
Construction:
1 Layer Bronze Screen 1 Layer 3oz. Copper Ground Plane Bonding: Copper Straps
Ground Plane Dimensions
(2) 2.44m x 0.76m x 0.78mm (8ft x 2.5ft x 0.031in) [see Figure – 5 below]
Distance from Cable Tunnel to Front of Ground Plane:
1.06m (42in)
Room Filters:
(2) 30A DC Filtered Lines (3) 30A DC/AC Filtered Lines
Power Availability:
115VAC 60Hz 1Phase 20 Amp Outlets Note: Other power arrangements are available upon request.
General Cabling Considerations:
Please note that the distance from the front edge of the monitor room table
and the test room ground plane is 10ft 7in. Plan cable lengths accordingly.
Mil Std Tests:
Power and interconnect leads need to be 2 meters in length within 10cm of the
front of the ground plane. (Ref 461E section 4.3.8.6.1 & 4.3.8.6.2)
DO‐160 Tests:
Power leads need to be 1 meter in length within 10 cm of the front of the ground
plane. Interconnect leads need to have 3.3 meters exposed and at least 1 meter
within 10 cm of the front of the ground plane. (Ref DO‐160G Section 20.3)
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 3 of 12
Figure ‐ 1: Room 11M (Test Room)
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 4 of 12
Figure ‐ 2: Room 11P (Monitor Room)
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 5 of 12
Figure – 3: Room R11P (Monitor Room) Upper & Lower waveguide locations (View from outside chamber)
Figure – 4: Room R11P (Monitor Room) Lower Waveguide opening
(View from inside chamber)
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 6 of 12
12in.
8'‐0"
10'‐6"
2'‐8"
2'‐3"
19'‐0"
18in. 18in.
6'‐0"
16'‐0"
8'‐0"
27.5in.
39.75in.
63.5in.12.5in.
50.0in.
2.25in.6'‐3 3/8"
12.5in.
1'‐0"
8'‐0" x 8'‐0" Door
11.5in.
4'‐0" x 7'‐0"Door
R11U Shielded Enclosure
20'‐0"
3'‐6"
3'‐9"
8in.
14in.
122.50in.
14in.
12in.
R11P Shielded Enclosure
Ground Plane
Ground Plane
7'‐1"
10'‐7"
Figure ‐ 5: Rooms 11M and 11P
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 7 of 12
Figure – 6: Room 11M Waveguide Mount (Test Room)
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 8 of 12
14.5in.
14.5in.
5/8"
5/8"
3 5/16"
3/8"
3 5/16"
2 1/4" 2 3/8"
1/2" 1/2"1/2" 1/2"
1/2"
3/8"
7/16"
7/16"
1/2"
3/8"3/8"
11/16"
7/16"
9/16"
9/16"
2 1/4"
2 3/8"
2 3/8"
2 5/16"
2 5/16"2 5/16"2 1/4"
2 5/16"
2 5/16"
2 3/8"
8"
7 15/16"
5/8"
9 13/16"
9 13/16"
3/8"
Figure – 7: Room R11U (Test Room) Large Waveguide Plate with 8 inch Copper Plate with Dimensions
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 9 of 12
14.5in.
14.5in.
5/8"
5/8"
3 5/16"
12.1in.
12.0in.
1 1/16" 2 1/2"
1" 15/16" 15/16" 15/16" 1"
1 1/16"
1"
1"
1"
1 1/16"1 1/16"1 1/8"1 1/8"1 1/16"
1"
1"
1"
1 1/16"
2 1/2"
2 7/16"
2 9/16"
2 7/16"
2 1/2" 2 9/16" 2 9/16" 2 1/2"
2 1/2"
2 1/2"
2 1/2"
2 7/16"
2 1/2"2 1/2"2 1/2"
5/16"
14.130in.
14.120in.3/8"
3 5/16"
Figure – 8: Room R11U (Test Room) Large Waveguide Plate with 12 inch Copper Plate with Dimensions
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 10 of 12
Figure – 9: Room R11U (Test Room) 8 Inch Copper Plate w/ Dimensions
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 11 of 12
Figure – 10: Room R11U (Test Room) 12 Inch Copper Plate w/ Dimensions
Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 630‐495‐9770 www.elitetest.com
NOTE: FOR ELITE CUSTOMER USE ONLY. Information listed here is subject to revision without notice. Actual chamber performance will depend on test item and specification requirements. Contact Elite for current test equipment information and test application assistance.
EMI CHAMBER DESCRIPTION TEST SUITE 11
Page 12 of 12
Figure – 11: Room 11U Waveguide Opening (Below Ground Plane Test Room)