FIRE REACTION A2 CLASS MOISTURE RESISTANCE ECO Ruredil HEAT RESISTANCE FIRE RESISTANCE + + NON-TOXIC for workers and the environment VALIDATION of reinforcement system DT 200/2013 Description RUREDIL XMESH C10 is a unique Fiber-Reinforced Cementitious Matrix (FRCM) composite system for the repair and strengthening of masonry constructions. It comprises of bidirectional carbon fiber mesh, namely RUREDIL XMESH C10, working as a continuous reinforcement and X Mortar 25 (RUREDIL X MORTAR 25) pozzolan-based hydraulic binder adhesive that anchors RUREDIL XMESH C10 to the masonry substrate. RUREDIL XMESH C10 is a high strength, bi-directional carbon fiber mesh with balanced weight. RUREDIL X MORTAR 25 is a pozzolan-based adhesive that must be mixed with water in the job site. Use • Increase shear and flexural strength of masonry structural panels • Eliminates the formation of connection lines of arches and vaults • Increase ductility of masonry structural elements • Historic masonry preservation • Seismic retrofit Applications • Interior and exterior • Panels, columns, arches and vaults • CMU, clay brick, hollow clay tiles, tuff and natural stone • Historic masonry Product Highlights • ICC-ES ESR-2013 listed product • Level of strengthening can be customized through the application of one or more sheets of RUREDIL XMESH C10 carbon fiber. • Once applied the system does not alter the response to fire of masonry construction and therefore fire protection is not required, even for indoor applications. • Durable in conditions in conditions of high environmental temperature since the system is not characterized by glass transition temperature limitations. • Does not deteriorate when exposed to alkali environment Ca(OH)2 Na(OH) K(OH) at pH>9.5 • Can be applied after rain over damp substrates • Not affected by moisture, it maintains its performance properties over time in humid environments. 1/6 RUREDIL X MESH C10 Composite strengthening system for repairing and strengthening of masonry constructions The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control [email protected] - www.ruredil.it Construction chemicals and building technologies Ruredil Technical info .................. 15. This edition cancels and replaces all previous editions. The safety data sheet and technical specifications may be downloaded from www.ruredil.it. PRODUCT CERTIFICATION AC 434 IN COMPLIANCE WITH GUIDELINES ACI 549
Transcript
FIREREACTION
A2CLASS
VALIDATIONof reinforcement
system
MOISTURERESISTANCE
PERMEABILITY Water Vapour
NON-TOXICfor workers
and the environment
ECORuredil
HEATRESISTANCE
FIRE RESISTANCE
INTERNATIONAL Patent
CHARACTERISTICS
FRP
DT200/2013
PCT++EN
UNIEN
VALIDATIONof reinforcement
system
MOISTURERESISTANCE
PERMEABILITY Water Vapour
NON-TOXICfor workers
and the environment
ECORuredil
HEATRESISTANCE
FIRE RESISTANCE
INTERNATIONAL Patent
CHARACTERISTICS
FRP
DT200/2013
PCT++EN
UNIEN
VALIDATIONof reinforcement
system
MOISTURERESISTANCE
PERMEABILITY Water Vapour
NON-TOXICfor workers
and the environment
ECORuredil
HEATRESISTANCE
FIRE RESISTANCE
INTERNATIONAL Patent
CHARACTERISTICS
FRP
DT200/2013
PCT++EN
UNIEN
DescriptionRUREDIL XMESH C10 is a unique Fiber-Reinforced Cementitious Matrix (FRCM) composite system for the repair and strengthening of masonry constructions. It comprises of bidirectional carbon fiber mesh, namely RUREDIL XMESH C10, working as a continuous reinforcement and X Mortar 25 (RUREDIL X MORTAR 25) pozzolan-based hydraulic binder adhesive that anchors RUREDIL XMESH C10 to the masonry substrate.
RUREDIL XMESH C10 is a high strength, bi-directional carbon fiber mesh with balanced weight. RUREDIL X MORTAR 25 is a pozzolan-based adhesive that must be mixed with water in the job site.
Use• Increase shear and flexural strength of masonry structural panels • Eliminates the formation of connection lines of arches and vaults • Increase ductility of masonry structural elements• Historic masonry preservation• Seismic retrofit
Applications• Interior and exterior• Panels, columns, arches and vaults• CMU, clay brick, hollow clay tiles, tuff and natural stone• Historic masonry
Product Highlights• ICC-ES ESR-2013 listed product• Level of strengthening can be customized through the application of one or more sheets of RUREDIL XMESH C10 carbon fiber.• Once applied the system does not alter the response to fire of masonry construction and therefore fire protection is not required, even for indoor applications. • Durable in conditions in conditions of high environmental temperature since the system is not characterized by glass transition temperature limitations.• Does not deteriorate when exposed to alkali environment Ca(OH)2 Na(OH) K(OH) at pH>9.5 • Can be applied after rain over damp substrates• Not affected by moisture, it maintains its performance properties over time in humid environments.
1/6
RUREDIL X MESH C10 Composite strengthening system for repairing and strengthening of masonry constructions
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
Ru
red
ilTe
chnic
al in
fo....
........
......1
5. T
his e
ditio
n ca
ncel
s and
repl
aces
all
prev
ious
edi
tions
.Th
e sa
fety
dat
a sh
eet
and
tech
nica
l spe
cific
atio
ns m
ay b
e do
wnl
oade
d fro
m w
ww
.rure
dil.i
t.
PRODUCTCERTIFICATION
AC434
IN COMPLIANCE WITH GUIDELINES
ACI549
• Can be applied on both clay bricks, hollow clay tiles, tuff, natural stone and CMUs. • The composite system does not require to be painted for UV protection• The composite system can be in a variety of climate conditions from 40°F (5°C) to 95°F (35 °C)• Composite systems provides visual prediction of potential failure through cracking and slippage of fibers.• Easy and safe to apply. Applicators do not need respirators and googles. Tools can be cleaned with water.
PackagingRUREDIL XMESH C10 carbon fiber is shipped in rolls, 3.28 ft (1 meter) wide and 49.21 ft (15 m) long corresponding approximately to 161,45 ft2 (15 m2) surface. Ruredil may be pre-cut the fabric upon request. RUREDIL X MORTAR 25 is available in 55 lb (25 kg) polyethylene-lined bags
Adhesive Mix Ratio1 bag of RUREDIL X MORTAR 25 requires 1.6 gal (6.5 L) to 1.8 gal (7 L) of water .
Coverage1 roll of RUREDIL XMESH C10 carbon fiber has 160 ft2 (15 m2) surface that approximately requires five 55 lb (25 kg) bags of RUREDIL X MORTAR 25.
Surface yield of RUREDIL X MORTAR 25 is 32 ft2 (3 m2) per 55 lb (25 kg) bag at 1/6 in (4mm) thickness.
Storage Store RUREDIL XMESH C10 carbon fiber indoors in a cool, dry area away from direct sunlight and moisture. Protect the fabric from flame or other hazards.
Store RUREDIL X MORTAR 25 adhesive indoors in a dry area at temperatures between 40 to 95°F (5 to 35°C). Do not store opened bags. Use up the whole package once it has been opened.
Shelf LifeRUREDIL XMESH C10 carbon fiber: 10 years in proper storage conditionsRUREDIL X MORTAR 25 adhesive: 24 months in sealed bags
VOC Content0 g/L
2/6
RUREDIL X MESH C10Structural Reinforcement
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
........
........
.....15
. Thi
s edi
tion
canc
els a
nd re
plac
es a
ll pr
evio
us e
ditio
ns.
The
safe
ty d
ata
shee
t an
d te
chni
cal s
peci
ficat
ions
may
be
dow
nloa
ded
from
ww
w.ru
redi
l.it.
3/6
RUREDIL X MESH C10Structural Reinforcement
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
........
........
..015
. Thi
s edi
tion
canc
els a
nd re
plac
es a
ll pr
evio
us e
ditio
ns.
The
safe
ty d
ata
shee
t an
d te
chni
cal s
peci
ficat
ions
may
be
dow
nloa
ded
from
ww
w.ru
redi
l.it.
PROPERTY TYPICAL TEST VALUE TEST METHOD
Compressive Strength7 days: 2,790 psi (19.3 MPa)
ASTM C10928 days: 3,500 psi (24.1 MPa)
Flexural Strength 28 days: 507 psi (3.5 MPa) UNI EN 196-1 (ASTM C78)Modulus of Elasticity 28 days: 1,052 ksi (7253 MPa) UNI EN 13412 (ASTM C469)Length Change 0.122% at 28 days – air cure ASTM C157
PROPERTY TYPICAL TEST VALUETensile strength 695 ksi (4,800 MPa)
Modulus Elasticity 34,810 ksi (240 GPa)
Elongation 1.8%
Nominal Thickness of Carbon Section at 0° and 90 ° 0.002 in (0.047 mm)
Density 113.6 lb/ft3 (1.82 g/cm3)
Weight of the Fibers 4.9 oz/yd2 (168 g/m2)
TECHNICAL DATATypical RUREDIL XMESH C10 Carbon Fiber PropertiesResults may differ upon mixing methods and equipment, temperature, application methods, site and curing conditions.
RUREDIL X MORTAR 25 Cement-Adhesive Properties
Design Values for Engineers and ArchitectsBased on the experimentation conducted in accordance with AC434 for the attainment of the Research Report ICC-ES ESR-2013, the values to be used for design of strengthening applications are listed in the tables below.The strengthening design of concrete and masonry structures should be conducted in accordance with the provisions of ACI 549.4R-13 “Guide to Design and Construction of Externally Bonded Fabric-Reinforced Cementitious Matrix (FRCM) Systems for Repair and Strengthening Concrete and Masonry Structures.” In addition to the methodology for design, ACI 549.4R-13 stipulates various limitations including: stress in the steel if existing, reinforcement stress due to creep rupture and fatigue, and reinforcement tensile strains as well as overall strength reduction factors.
Material Characteristics of Carbon FRCM RUREDILX MESH C10Material properties of the FRCM composites for design purposes per ACI 549.4R-13 guidelines are tensile modulus of elasticity of cracked specimen, composite ultimate tensile strength, and composite ultimate tensile strain. Material properties of the Carbon FRCM system obtained per AC434 are given in the following table.
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
........
........
015.
Thi
s edi
tion
canc
els a
nd re
plac
es a
ll pr
evio
us e
ditio
ns.
The
safe
ty d
ata
shee
t an
d te
chni
cal s
peci
ficat
ions
may
be
dow
nloa
ded
from
ww
w.ru
redi
l.it.
HOW TO USEDesignRUREDIL XMESH C10 strengthening system should be designed to meet the specific project design requirements. Ruredil provides engineering exploratory design at no obligation.
InstallationRUREDIL XMESH C10 must be applied in strict compliance with the installation instructions reported in this Technical Data Guide by trained applicators approved by Ruredil.
Surface Preparation•Masonry substrate must be structurally sound. Pointing mortar must be fully cured (28 days). •Masonry surface must be clean, free of any treatments, such as plasters, primers, etc. that may affect the adhesion of RUREDIL RUREDIL XMESH C10 C10 strengthening system.
•Acceptable surface preparation methods include sandblasting and low-pressure water jet cleaner with brushing.•In presence of macroscopic defects deeper than 1/4 in (6.3 mm), the substrate must be regularized using RUREWALL T Structural from Ruredil or equivalent product based on hydraulic binder preferably with pozzolan characteristics. Cure not less than 24 hours before applying RUREDIL RUREDIL XMESH C10 C10 strengthening system. Do not trowel the surface of the repair material to a smooth finish.•Always round corners to at least a ½ in. radius. Internal corners should be smoothed by troweling. •Ruredil staff will provide proper specifications and details based on the project requirements.
Mixing•Precondition RUREDIL X MORTAR 25 pozzolan-based adhesive to 70°F (21°C) before mixing. •Mix in a pail using hand-held slow-speed drill and a paddle pail. Alternatively use a mortar mixer with a rotating drum. Do not mix by hand.•Pour potable water into mixer. Use a maximum of 1.7 gal (6.3 L) of water per 55 lb (25 kg) bag of RUREDIL X MORTAR 25. Do not deviate from the recommended water content.•Add the powder to the water while continuously mixing for a minimum of 2 minutes.•Add a maximum of 1.5 pint (0.7 L) of water and mix for additional 2 minutes. Total quantity of water should not exceed 1.9 gal (7 L)•Let the mix rest for 2-3 minutes •Mix again for 2-3 minutes. •RUREDIL X MORTAR 25 adhesive should be lump-free before application.
Application•Dampen the substrate. In case of high ambient temperatures and/or low RH, mist the substrate frequently during the application so to prevent early drying out of the adhesive.•Remove standing water before application.•Cut RUREDIL XMESH C10 as necessary. Use normal scissors. •Apply RUREDIL X MORTAR 25 adhesive over the masonry substrate with a steel trowel at a thin thickness of 1/6 in (4 mm).•Lay RUREDIL XMESH C10 over the adhesive with orientation of 0°/90° with respect to the ground level or masonry set line. Lightly press RUREDIL XMESH C10 into the adhesive. Each sheet of RUREDIL XMESH C10 must be totally encapsulated in the thickness of RUREDIL X MORTAR 25 adhesive. •If the structural design requires two sheets of RUREDIL XMESH C10, add a second layer of RUREDIL X MORTAR 25 adhesive at 1/8 to 1/6 in (3 to 4 mm) thickness, a second sheet of RUREDIL XMESH C10 and embed it into the thickness of the adhesive.Repeat the sequence
RUREDIL X MESH C10
5/6
as specified by the designer. Usually RUREDIL RUREDIL XMESH C10 C10 composite system requires from 1 to 3 sheets of RUREDIL XMESH C10.•When multiple layers are applied, alternate the 0°/90° orientation with the +45°/-45° orientation (diagonally to the previous mesh layer) unless required differently by the designer. •Complete the installation adding a final layer of RUREDIL X MORTAR 25 adhesive at 1/8 in (3 mm) thickness so as to encapsulate the final sheet of RUREDIL XMESH C10.•Each layer of RUREDIL X MORTAR 25 adhesive must be applied when the previous layer is still wet and has not hardened.•If the surface of RUREDIL X MORTAR 25 adhesive has hardened, sandblast before applying a new layer of adhesive.•When the application is interrupted, all required sheets of RUREDIL XMESH C10 must have been applied. •RUREDIL XMESH C10 must be lapped 6 inches minimum. •RUREDIL X MORTAR 25 must be applied from 40 to 95°F (4 to 35°C). Follow ACI 305 and 306 for application in hot and cold weather.
CuringIn hot and dry weather conditions and/or in presence of wind, the surface of RUREDIL X MORTAR 25 adhesive must be protected with CURING S from Ruredil or equivalent product. The curing compound must be suitable for applications on wet hydraulic mortars in order to reduce water evaporation
Clean upClean tools with water immediately after use. Cured material must be removed mechanically.
Limitations• RUREDIL RUREDIL X MESH C10 composite system cannot be applied over metal
surfaces• RUREDIL X MESH C10 composite system cannot be used for strengthening wooden
piles• Do not exceed the recommended application thickness for RUREDIL X MORTAR 25
more than 1/6 in. (4 mm)• RUREDIL X MORTAR 25 must be protected from rain, even light rain, during
application• RUREDIL X MORTAR 25 should not be applied in hot temperature higher than 95°F
(35°C) or with moderate or strong winds• RUREDIL X MORTAR 25 cannot be spray applied. It can only be applied by trowel.• RUREDIL X MORTAR 25 cement-based adhesive cannot be used for masonry
pointing. • Do not use RUREDIL X MORTAR 25 as a repair mortar. If repair is necessary before
the application of RUREDIL XMESH C10 strengthening system, use RUREWALL T Structural from Ruredil or equivalent product based on hydraulic binder with pozzolan characteristics.
• Do not mix partial bags of RUREDIL X MORTAR 25.• Do not mix RUREDIL X MORTAR 25 by hand.• Do not add plasticizers, accelerators, retarders, or other additives to RUREDIL X
MORTAR 25.• For professional use only.• Make sure that the most current version of the product data sheet and SDS are being
used. Contact Ruredil at [email protected] for information. • Proper application is the responsibility of the user. Ruredil’s personnel make technical
recommendations but do not supervise job site applications
Structural Reinforcement
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
........
........
5. T
his e
ditio
n ca
ncel
s and
repl
aces
all
prev
ious
edi
tions
.Th
e sa
fety
dat
a sh
eet
and
tech
nica
l spe
cific
atio
ns m
ay b
e do
wnl
oade
d fro
m w
ww
.rure
dil.i
t.
RUREDIL X MESH C10
6/6
Chemical/physical specifications:Mesh length: 15 m ± 3%
Composition:Carbon fiber mesh.
Definition of performance:Bi-directional carbon mesh for structural reinforcements with inorganic base of masonry structures.
Our company is certified according to UNI EN ISO 9001:2008 standard by ICMQ and Certiquality for the “Design, production and trade of chemical and special products for the building sector.” Our quality system is based on the sale through catalog, a contractual tool between our Company and Customers. Ruredil, with this tool, guarantees to its Customers that the product to be delivered complies with the specific chemical and physical properties specified in this catalog sheet.This sale relieves us from the issuance of the certificate of analysis which, by its nature, only guarantees the performance of a specific supply.
Our company is certified according to UNI EN ISO 9001:2008 standard by ICMQ and Certiquality for the “Design, production and trade of chemical and special products for the building sector.” Our quality system is based on the sale through catalog, a contractual tool between our Company and Customers. Ruredil, with this tool, guarantees to its Customers that the product to be delivered complies with the specific chemical and physical properties specified in this catalog sheet. This sale relieves us from the issuance of the certificate of analysis which, by its nature, only guarantees the performance of a specific supply.
Packaging15 m2 rolls (length 15 m, height 100 cm)
Consumption:To consider a web overlap of approx. 10 cm on the junctions.
........
.12
CATALOGUE SPECIFICATIONS RUREDIL X MESH C10
Code0109113020
Structural Reinforcement
Construction chemicals and building technologies
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
HEALTH, SAFETY AND ENVIRONMENTALRead, understand and follow all Safety Data Sheets and product label information for this product prior to use. SDS can be obtained by e-mailing a request to [email protected]
Use only as directed.
Statement of Responsibility The technical information and application advice in this technical data guide is based on the present state of our best scientific and practical knowledge. As the nature of the information herein is general, no assumption can be made as to the product’s suitability for a particular use or application, and no warranty as to its accuracy, reliability or completeness, either expressed or implied, is given other than those required by State legislation. The owner, his representative or the contractor is responsible for checking the suitability of products for their intended use. Field service, where provided, does not constitute supervisory responsibility. Suggestions made by Ruredil., either verbally or in writing, may be followed, modified or rejected by the owner, engineer or contractor since they, and no Ruredil, are responsible for carrying out procedure appropriate to a specific application.
DescriptionRUREDIL X MORTAR 25 is an adhesive based on pozzolanic cement for bonding RUREDIL X MESH C10 (carbon fabric) onto masonry surfaces, such as concrete masonry unit (CMU), clay brick, hollow clay tiles, tuff and natural stone. It is designed for exclusive use with RUREDIL XMESH C10 composite strengthening system for masonry construction. RUREDIL X MORTAR 25 is easy to apply by hand even in challenging conditions due to its high workability. It is safe for applicators with no offensive odors.
UseRUREDIL X MORTAR 25 adhesive combines with RUREDIL XMESH C10 (carbon fabric) mesh to provide RUREDIL X MESH C10 composite system for strengthening of masonry structures. It is suitable for applications over old stones and bricks in historic masonry preservation.
Applications CMU, tuff, natural stone, clay brick and hollow clay tile Historic masonry Interior and exterior Vertical and overhead
Product Highlights Easy to apply by trowel for vertical and overhead applications. Suitable for applications on rough and irregular masonry surfaces Only requires potable water for mixing Can be mixed with a slow-speed drill and paddle or mortar mixer Can be applied on damp surfaces as long as there is no standing water Does not alter the response structural elements to fire thus allowing indoor
applications of RUREDIL X MESH C10 composite strengthening system without fire protection
Not affected by salt water Water vapor permeable Very limited, if no shrinkage Resistant to freeze-thaw cycles RUREDIL X MORTAR 25 has similar compressive strength and modulus of elasticity
as most of the masonry materials, thus facilitating stress-strain transfer between the adhesive and the substrate
100% solvent free
Ru
red
ilTe
chnic
al in
fo
1/5
RUREDIL X MORTAR 25
Pozzolan-based Hydraulic Binder Adhesive for Use in Combination with Carbon Fiber Mesh in RUREDIL X MESH C10 Composite Strengthening
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
[email protected] - www.ruredil.it Construction chemicals and building technologies
........
........
.....T
his e
ditio
n ca
ncel
s and
repl
aces
all
prev
ious
edi
tions
.Th
e sa
fety
dat
a sh
eet
and
tech
nica
l spe
cific
atio
ns m
ay b
e do
wnl
oade
d fro
m w
ww
.rure
dil.i
t
Packaging55 lb (25 kg) polyethylene-lined bags
Adhesive Mix Ratio 1 bag of RUREDIL X MORTAR 25 requires 1.6 gal (6.5 L) to 1.8 gal (7 L) of water.
Coverage 32 ft2 (3 m2) for 1/6 in (4mm) thickness per 55 lb (25 kg) bag.
StorageStore indoors in a dry area at temperatures between 40 to 95°F (5 to 35°C). Do not store opened bags. Use up the whole package once it has been opened.
Shelf Life24 months in sealed bags
VOC Content0 g/L
Technical DataResults may differ upon mixing methods and equipment, temperature, application methods, site and curing conditions.
2/5The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
Application LifeApproximately 45 minutes at 70° F (21° C)
after adding powder to the water UNI EN 1015-9
Fresh Wet Density 93.6 lb/ft3 (1.5) g/cm3 UNI EN 1015-6Flow 165 mm (6.5 in.) UNI EN 13395-1
Compressive Strength7 days: 2,790 psi (19.3 MPa)
28 days: 3,500 psi (24.1 MPa) ASTM C109
Flexural Strength 28 days: 507 psi (4.0 MPa) UNI EN 196-1 (ASTM C78)Modulus of Elasticity 28 days: 1,052 ksi (6,998 MPa) UNI EN 13412 (ASTM C469)Length Change 0.122% at 28 days – air cure ASTM C157
How to useInstallationRUREDIL X MORTAR 25 must be applied for RUREDIL X MESH C10 strengthening applications by contractors that are trained and approved by Ruredil.
Surface preparationMasonry substrate must be structurally sound. Pointing mortar must be fully cured (28 days). Masonry surface must be clean, free of any treatments, such as plasters, primers, etc. that may affect the adhesion with RUREDIL X MORTAR 25.Acceptable surface preparation methods include sandblasting and low-pressure water jet cleaner with brushing. In presence of macroscopic defects deeper than 1/4 in (6.3 mm), the substrate must be regularized using RUREWALL T Structural from Ruredil or equivalent product based on the hydraulic binder with pozzolan characteristics.
3/5The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
Mixing Precondition to 70°F (21°C) before mixing. Mix in a pail using hand-held slow-speed drill and a paddle. Alternatively use a mortar
mixer with a rotating drum. Do not mix by hand. Pour potable water into mixer. Use a maximum of 1.7 gal (6.3 L) of water per 55 lb
(25 kg) bag of RUREDIL X MORTAR 25. Do not deviate from the recommended water content.
Add the powder to the water while continuously mixing for a minimum of 2 minutes. Add a maximum of 1.5 pint (0.7 L) of water and mix for 2 minutes. Total quantity of
water should not exceed 1.9 gal (7 L) Let the mix rest for 2-3 minutes Mix again for 2-3 minutes. RUREDIL X MORTAR 25 should be lump-free before application.
Application Dampen the substrate. In case of high ambient temperatures and/or low RH, mist
the substrate frequently during the application so to prevent early drying out of the adhesive.
Remove standing water before application. Apply RUREDIL X MORTAR 25 by trowel, preferably using a steel trowel. RUREDIL X
MORTAR 25 cannot be sprayed. Apply RUREDIL X MORTAR 25 as part of RUREDIL RUREDIL XMESH C10 C10 composite strengthening system in order to encapsulate the carbon fiber mesh and bond it onto the masonry substrate. Be sure to apply RUREDIL X MORTAR 25 in thin layers not exceeding 1/6 in. (4 mm) thickness.
Do not use RUREDIL X MORTAR 25 as a point mortar or to repair imperfections of the substrate deeper than 1/4 in (6.3 mm).
RUREDIL X MORTAR 25 must be applied in the temperature range of 40 to 105°F (5 to 40°C). Follow ACI 305 and 306 for application in hot and cold weather
CuringIn hot and dry weather conditions and/or in presence of wind, the surface of RUREDIL X MORTAR 25 must be protected with CURING S from Ruredil or an equivalent product. The curing compound must be suitable for applications on wet hydraulic mortars in order to reduce water evaporation.
Clean upClean tools with water immediately after use. Cured material must be removed mechanically.
Limitations Use RUREDIL X MORTAR 25 as a component of RUREDIL X MESH C10. Do not use RUREDIL X MORTAR 25 as a repair mortar. If repair is necessary before the
application of RUREDIL X MESH C10 strengthening system, use RUREWALL T Structural from Ruredil or equivalent product based on hydraulic binder preferably with pozzolan characteristics
RUREDIL X MORTAR 25 adhesive must be applied in a thin layer, not thicker than 1/6 in. (4 mm).
RUREDIL X MORTAR 750 cannot be sprayed. It can only be applied by trowel.
The information contained in this technical info sheet is based on our knowledge and experience, and cannot be considered to represent a guarantee on our part, or an acceptance of responsibility for use of our products, as conditions of use are beyond our control
Do not add sand, fine aggregate, or Portland cement to RUREDIL X MORTAR 25Do not mix RUREDIL X MORTAR 25 by hand.Do not deviate from the amount of water recommended in this product data sheet. Protect the application during the first 24-48 hours after completing the installation in
conditions, such as high ambient temperature and low RH that can cause rapid drying of RUREDIL X MORTAR 25 cement-based adhesive.
When mixing or placing in a closed area, provide adequate ventilationFor professional use onlyMake sure that the most current version of the product data sheet and SDS are being
used. Contact Ruredil at [email protected] for information Proper application is the responsibility of the user. Ruredil personnel make technical
recommendations but do not supervise job site applications.
Health, safety and environmentalRead, understand and follow all Safety Data Sheets and product label information for this product prior to use. SDS can be obtained by e-mailing a request to [email protected] Use only as directed.
Statement of responsibilityThe technical information and application advice in this technical data guide is based on the present state of our best scientific and practical knowledge. As the nature of the information herein is general, no assumption can be made as to the product’s suitability for a particular use or application, and no warranty as to its accuracy, reliability or completeness, either expressed or implied, is given other than those required by State legislation. The owner, his representative or the contractor is responsible for checking the suitability of products for their intended use. Field service, where provided, does not constitute supervisory responsibility. Suggestions made by Ruredil., either verbally or in writing, may be followed, modified or rejected by the owner, engineer or contractor since they, and not Ruredil, are responsible for carrying out procedure appropriate to a specific application.
4/5Construction chemicals and building technologies
Chemical/physical specifications:Density ():specific gravity (fresh mortar): 1,50 ± 0,05 g/ccConsistency: 165 mm ± 10 Compliant with the UNI EN 998-2 standard
Composition:
Stabilized pozzolanic inorganic matrix.
Definition of performance:Stabilized pozzolanic inorganic matrix for FRCM structural reinforcements of masonry buildings and structures.
Our company is certified according to UNI EN ISO 9001:2008 standard by ICMQ and Certiquality for the “Design, production and trade of chemical and special products for the building sector.” Our quality system is based on the sale through catalog, a contractual tool between our Company and Customers. Ruredil, with this tool, guarantees to its Customers that the product to be delivered complies with the specific chemical and physical properties specified in this catalog sheet.This sale relieves us from the issuance of the certificate of analysis which, by its nature, only guarantees the performance of a specific supply.
