5G4G3G2G

The S60z Integration Module

The S60z AP Module is a compact SDR platform which allows integrators to quickly build a full small cell system. The S60z AP is targeted at specialist integration applications including security and surveillance, private networks and research and development.

Multi-band support

The platform is frequency agile from 450MHz up to 3.8GHz, supporting all standard 3GPP bands for both 3G and 4G (LTE, FDD and TDD). The S60z is a multi-technology module that supports 2G, 3G and 4G, with R15 non-standalone (NSA) 5G primary cell capability by software upgrade. This makes it the first integrator module to offer full multi-technology platform with a future proof elegant migration path to 5G.

Based on the S60 family

The S60z AP module is based on the S60 4G AP platform, and runs the same carrier-grade 3GPP stack and application software. This makes it easy for integrators to work with the family of S60 products in a unified way.

The S60z comes with fully managed flexible cellular software stacks and presents 3GPP compliant S1 and Iuh interfaces.

High-performance synchronisation

The S60z AP module includes a high-performance OCXO to deliver excellent frequency stability, as well as integrated GPS and IEEE1588 support, providing a multi-layered synchronisation mechanism for robust and accurate timing in both FDD and TDD modes.

Versatile RF solution for different applications

The S60z AP module allows switching between frequency bands in only a few seconds, so allowing integrators to build frequency-agile APs and receivers at low cost. The RF output power at +5dBm has been specified to give a useful input level for whatever amplifier the integrator chooses to add, extending the range up to 10km. Connectorised Tx and Rx ports for 2x2 MIMO are provided, allowing the option to separate the antennas for best performance.

Compact module

The S60z AP module is very compact, measuring only 147mm x 123mm, and drawing only 11W of DC power it provides a quick drop-in solution for integrators. The MCX connectors allow easy snap-on attachment of RF cables without the need for physical space to tighten with a spanner.

www.ipaccess.com

S60zUnbanded SDR Module for integrators

The S60z is an unbanded multi-technology SDR integration module for specialist applications

S60z AP Module

Radio

Connectorised Low band 450MHz to 2.8GHz

Connectorised High band 3.3GHz to 3.8GHz

Band switching < 5sec for 4G < 50sec for 3G

Max Tx power +5dBm per port

4G

Supports all standard EARFCNs up to 3.8GHz

2 x 2 MIMO

3 / 5 / 10 / 15 / 20 MHz channel bandwidths

Up to 32 active users

Up to 150/50Mbps for FDD (bandwidth dependent)

Up to 110/10Mbps for TDD (bandwidth dependent)

VoLTE or CSFB to GERAN/UTRAN for voice

Warning system broadcast - CMAS and ETWS supported

Full GBR and non-GBR support with QoS aware scheduler

3G

Supports all standard ARFCNs up to 2.8GHz

Up to 24 active users (option for 30)

HSPA 21/5.75 Mbps

CS voice: AMR

WB-AMR (Config-A)

Multi-RAB to each UE: CS voice and/or up to 3

HSDPA/HSUPA

or

CS voice and/or up to 2 R99 PS

Iu-Flex and MOCN support

Cell broadcast

S60z Access Point Module

4G and 3G Mobility

Reselection to/from macro layer & APs Intra-frequency, inter-

frequency, inter-RAT

Handover to/from macro layer & between APs Intra-frequency, inter-

frequency, inter-RAT

4G and 3G Interfaces

LTE S1 (S1-Flex via gateway), X2-GW

3G Iuh

Uu LTE and 3G air interfaces to standard LTE and 3G UEs

Network Listen

Network listen to support radio synchronisation and RF planning

LTE: Scans LTE and 3G neighbours

3G: Scans 3G and 2G neighbours

2G

Supports all standard GSM bands

Signalling only (includes SMS) without ciphering

Fixed timeslot configuration

5G

R15 NSA 5G primary cell capability

Maximum flexibility for specialist applications including OpenAir™ API support.

S60z

www.ipaccess.com

© 2019 ip.access Ltd. ip.access, viper™, nanoLTE™, Oyster3G®, nano3G® and nanoGSM® are trademarks of ip.access Ltd. All other trademarks are acknowledged. Information in this document is subject to change without notice and may contain errors. No responsibility is assumed by ip.access for the use of this information, nor for infringements of patents or other rights of third parties. The documentation and/or software may provide links to Web sites and access to content, products, and services from third parties. ip.access is not responsible for the availability of, or any content provided on, third-party Web sites. You bear all risks associated with the use of such content. This document is the property of ip.access and implies no license under patents, copyrights, trade secrets or other intellectual property rights. No part of this publication may be copied, reproduced, stored in a retrieval system, or transmitted, in any form of any means, electronic, photographic, or otherwise, or used as the basis for manufacture or sale of any items without the prior written consent of ip.access. S60z Datasheet 201902 v1.0.

140mm

100mm

110mm

4.2mm

100mm 123mm

22.1mm

147mm

Synchronisation

High stability OCXO

NTP support

IEEE1588v2 support

1PPS port

Network Listen

GPS

Physical interfaces

Ethernet port 1Gbps

MCX connectors TX1, TX2, RX1, RX2,

2 x Network Listen, GPS Antenna, 1 PPS input, External clock input

I/O port Control signalling

Environmental & physical

Dimensions 147 x 123 x 22.1mm

Temperature range 0° to 45°C

Operating humidity 10 to 70% non-condensing

Power input 12V DC

S60z Dimensions