SAFE (DRINKING) WATER ON BOARD

safe Water on board CatalogueProviding your water from production to consumption

Safe Water on Board CatalogueProviding your water from production to consumption

Catalogue 2016

110yearsA N N I V E R S A R Y !

1 9 0 6 - 2 0 1 6

2 | www.hatenboer-water.com

This catalogue ‘Safe Water on Board’ was composed to support you in finding the right products or (spare) parts to maintain your water quality on board. Apart from that you will learn about our worldwide services as well as our custom built solutions. That is what Hatenboer-Water is famous for in the maritime and offshore world; on the basis of our longstanding experience we became specialists in drinking water treatment and we gained the roll of full service partner.

Fortunately a wide range of clients acknowledge this and we are proud that our customer base is growing every day as our mission is to provide you sustainably with water of the right quality: good water quality is essential for a safe work environment for your crew!

It is not possible to incorporate our total scope of supply in this publication. However, we invite you to consult this catalogue and our organisation so we can assist you in any way to improve your water quality on board and by that secure your license to operate. Your remarks and comments for further improvement of this publication are of course highly appreciated. Willem Buijs

CEO Hatenboer-Water

Hatenboer-WaterWelcome to the world of water


Opening Standard Maritime Flow Chart Reliable design of water production

and distribution p.6

Hatenboer-Water

Introduction p.10

Where to find us

Contact details p.12

Worldwide agents p.13

Hadex® stock points p.14

Custom Built Solutions

Tailored to the conditions p.20

RO fresh water generators p.20

Hydrophore units p.22

Hot and cold water modules p.22

Disinfection modules p.23

Products, Spares and Consumables 1. Desalination

1.1 Reverse osmosis standard series p.24

Oceanus series p.26

Proteus series p.28

2. Disinfection

2.1 Hadex® food grade drinking

water disinfectant p.32

2.2 Demitec® ultra violet

disinfection p.38

2.3 LiquiTech™ copper/silver

ionisation p.42

2.4 HWSIS silver ionisation p.44

3. Distribution

3.1 Grundfos pumps p.48

3.2 Hydrophore vessels p.52

3.3 Cat maritime high pressure

pumps p.56

3.4 Kemper valves p.58

Hatenboer-WaterContents

4. Water Filtration

4.1 Filter housings p.62

4.2 Filter cartridges p.66

4.3 Filter media p.70

5. Water Conditioning

5.1 Neutralising filters p.76

5.2 Automatic dosing units p.78

5.3 Chemicals for stabilising, cleaning

or anti scaling p.82

5.4 Demineralisers p.86

5.5 Water softeners p.88

6. Water Monitoring

6.1 Fresh water test kits p.92

6.2 Hadex® test kits p.96

6.3 Sewage effluent test kits p.100

6.4 Boiler water test kits p.104

6.5 Cooling water test kits p.106

6.6 Single parameter

measuring devices p.108

7. Water Heating

7.1 Reliable hot water calorifiers

supply p.117

8. Water Consumption

8.1 Safe water on the spot p.119

Services Water Quality Consultancy

Potable water courses p.134

Troubleshooting p.136

Cleaning and disinfection p.137

Worldwide water tests p.138

Water management p.140

Technical Services

Surveys p.146

Service agreements p.147

Mid-life updates p.148

Cold stacking p.149

Operator trainings p.150

Disclaimer

Registered trademarks p.154


Standard Maritime Flow ChartSafe Water On Board

Bunkering water or making drinking water from sea water is a

routine job. As soon as drinking water is in your storage tanks a more

challenging task starts: keeping the drinking water and the whole

water distribution system in good condition. Relatively high

tem peratures make the water quality deteriorate quicker than you

might imagine. Think of tanks situated next to engine rooms, when

operating in tropical environments or water lines which run through

the engine room. Suddenly water can become dangerous for the

health of your crew. Therefore it is of the greatest importance that

one should look after the whole drinking water treatment line from

the source to the tap.

Reliable designHatenboer-Water created the standard maritime flow chart to give

you some more understanding of all steps to be considered for a

reliable design of your water storage and distribution lay out. Our

installed base of over 2000 water systems gives us a thorough

understanding of water flows, applicable regulations and the

influences from outside that might influence your water quality.

This catalogue offers an overview of all our solutions, services and

products for your water management. The flow chart helps you to

find the products you are interested in. Feel free to contact us for

any additional explanation.

1. Fresh (drinking) water at sea can be produced by means of desalination for which an evaporator or Reverse Osmosis plant is required. Also fresh drinking water can be bunkered from shore or from HDU barges (1.1). More info on page 24.

2. Hadex® drinking water disinfectant can be dosed in water maker product water, bunkering water and/or fresh water to the chlorine based distribution system. As an effective and essential method to reduce the number of micro-organisms and to avoid bacterial growth in the fresh water storage tanks and piping systems. More info on page 32.

3. Neutralising (Mineralising) filters are used for the conditioning of the product water from the evaporator or reverse osmosis desalinator. The water from a water maker hardly contains any natural hardness, is without taste and has a low pH. To prevent pipe corrosion and harmful effects of this pure product water, neutralising is applied. More info on page 76.

4. Hydrophore units, pressurise the system to the tap points in the required quantity. More info on page 52.

5. Fine filters remove solid impurities such as rust, sand and all kind of other debris. Especially at locations where the water contains turbid matter we advise fine filtration of the water as a basic treatment step in water purification. More info on page 66.

5.1 Activated carbon filters improve the taste and appearance of the water, removing organic micro-pollutants such as traces of hydrocarbons (oil, solvents) and are also used for dechlorination. More info on page 62.

6. Potable water stabiliser is used where problems with corrosion occur in the distribution system (rusty water). The HW-Stabiliser stabilises the corrosion layer and forms a hard layer, stopping any further corrosion. More info on page 80-85.

7. Ultra Violet (UV) disinfection eliminates bacteria in fresh water. An UV system needs to be installed as last treatment step to the users tap points. More info on page 38.

8. Hot water calorifiers provide the hot water needed on board for galley, showers, laundry, etc. The heating can be by electricity, steam, hot water or thermal oil, whatever is available on board.

More info on page 115.

9. Water softeners are required to protect water-fed equipment, such as oil separators, boilers, cooling and piping systems against formation of mineral scale. More info on page 88.

10. De-ionised pure water is required for batteries, chemicals, analysis and special cleaning. More info on page 86.

11. Water coolers provide cold fresh consumption water on the spot. More info on page 119.

12. For quality control and proper maintenance of the fresh drinking and technical water systems on board we deliver test kits for most parameters, such as pH, conductivity, hardness, chlorine, etc. More info on page 92.

Furthermore we offer practical and theoretical trainings. More info on page 130.

1 1.1

2

22

3

5

47

11

2 6

12

9 10

8


Hatenboer-WaterSafe Water on Board

Hatenboer-WaterFresh in water since 1906

Water treatment With 110 years of specialist expertise, in-house engineering, design

and production in a modern operating environment, Hatenboer-Water

supplies solutions for all your water-related challenges and basic

needs. Economically sound and environmentally sustainable with

all necessary worldwide after sales service. Hatenboer-Water, your

partner in maritime water treatment and services.

Maritime expertise Good and safe water on board is essential for the operation of any

vessel or rig. Our vast maritime experience gives us a thorough

understanding of your operations. We treat water from every source

till it is of the proper quality on every tap point. Safe and healthy.

The track record of more than a thousand maritime water treatment

units worldwide is proof of our high standards. Integrated in our total

scope of supply; from a standard product such as a pump or filter,

right up to fully integrated custom-made skid built water treatment

systems.

Solutions by Hatenboer-Water are designed with sustainability and

environment in mind. Please contact us for more details on energy

saving, low life-cycle costs and sustainability of our solutions.

Safe water on board means a safe work environment

for your crew.


ServicesOperational uptime and return on your investment will be

maximised when installation, commissioning and maintenance

of your drinking water systems are done properly.

The professional service department of Hatenboer-Water will take

full care of your system. That means your crew can focus on their

specialist work. Many of our relations encounter the benefits of

a customised ‘Hatenboer-Water Service Agreement’.

Expert consultancy Our Water Quality department delivers solutions so you can comply

to international laws and regulations and are assured that your crew

is working in safe conditions. Poor design, corrosion and biofilm may

cause serious health risks, system failures and an unsafe working

environment on board. You are able to prevent these issues by

using our expertise in potable water systems, technology and the

applicable laws.

We come forward with solutions and services that are always

practical and dedicated like potable water courses, operator

trainings, water sampling and analyses.

Your benefits choosing Hatenboer-Water

• Good water from production to consumption

• Strong focus on service, quality, innovations and improvement

• Minimal downtime

• Easy access to spare parts and consumables

• Dedicated after sales and logistics support

• Worldwide services

• Local, skilled, support

• Unsurpassed quality

Hatenboer-Water in a nutshell

• More than 100 experienced professionals

• Based in the Netherlands and Singapore

• All disciplines and facilities under one roof

• In-house engineering, 3D CAD design

• Continuous R&D

• Fully equipped workshop

• Privately owned

• Stocked warehouses for short delivery times

Your partner in maritime water treatment and services.

ISO 9001 ISO 14001 VCA*

The Netherlands & SingaporeWhere to find us

Hatenboer-Water The NetherlandsWith all modern technologies, the world gets smaller every year.

Local representation is often a way to ensure quick

delivery and response times, which can be crucial for your

operations. For that reason, Hatenboer-Water has a selected

worldwide agent network.

Hatenboer-Water Asia in SingaporeSince many new builds and retrofits take place in Asia, and our wish

to provide expert guidance in these projects for both shipyards and

end-users, we have our fully stocked subsidiary in Singapore.

Here you can also apply for services and water sampling.

The NetherlandsHATeNBOeR-WATeR BV

HeAD OFFICe:Mercuriusweg 8, 3113 AR Schiedam

POSTAL ADDReSS:P.O. Box 6013, 3002 AA Rotterdam

CeNTRAL WAReHOuSe:Fortunaweg 15, 3113 AN Schiedam

e [email protected] +31 (0)10 409 12 00F +31 (0)10 409 12 10

SALeS: e [email protected]

SAMPLING AND ANALySIS:e [email protected]

POTABLe WATeR COuRSeS:e [email protected]

SeRvICeS:e [email protected]

SingaporeHATeNBOeR-WATeR ASiA PTe LTD

OFFICe AND WAReHOuSe:22 Boon Lay Way#01-57 Tradehub 21609968 Singapore SWT +65 6515 8021

ALL SeRvICeS:e [email protected]

www.hatenboer-water.com


China (North)eASTSUCCeSS MARiNe LTD.Room 2411, Tower B, Harbourview PlaceNo. 4 Wuwu RoadZhongshan District116001 DalianChina

T +86 411 8807 9375F +86 411 8807 9378e [email protected]

China (Middle / South)HiPSON MARiNe (CHiNA) LTD.West, #13 Building No. 300 Shuang Qiao Road200129 ShanghaiChina

T +86 213 3820 950 60 105F +86 213 3820 930e [email protected] www.hipson.biz

GCC CountriesUNiTeD TeCHNiCAL SeRViCeSPlot No. 3ESector MN-3 MusaffahAbu DhabiGCC Countries

T +971 4 339 27 55M +971 50 557 33 21e [email protected]

indiaiNDOSTAN CORPORATiON39/3556 IshwaryaNeduvelil Lane, Ravipuram Road682 016 Cochin, KeralaIndia


MalaysiaTeRRA eNeRGY SDN BHD Suite 3.04, Level 2, Wisma Central, Kuala Lumpur City Centre PO Box 207 Jalan Ampang 50450 Kuala Lumpur Malaysia

T +6(03) 2163 3366 F +6(03) 2162 3366 e [email protected] www.terraenergy.com.my

South KoreaDONG SUNG CO. LTD.#1725 century O/T 55-1Daeteon - 3Dong, Nam-Gu608-743 BusanSouth Korea


TurkeyNAVALTiS LTD.Naval Architecture & EngineeringKemankes Mah. Kara Ali Kaptan Sok.No: 7 KarakoyIstanbul TR – 34425Turkey

T +90 532 768 7050 T2 +90 532 573 1374e [email protected]

Your benefits• Quick delivery and response times

• Local stock of key spare parts and consumables

• Limited down time

• Technical support during tenders and project realisation

Worldwide agentsWhere to find us

Hadex® stock pointsWhere to find us

To have easy access to this food grade

water disinfectant, we have several

stockists of Hadex® that you can contact:

The NetherlandsHATeNBOeR-WATeR BV

HeAD OFFICe:Mercuriusweg 8, 3113 AR Schiedam

POSTAL ADDReSS:P.O. Box 6013, 3002 AA Rotterdam

CeNTRAL WAReHOuSe:Fortunaweg 15, 3113 AN Schiedam

e [email protected] +31 (0)10 409 12 00F +31 (0)10 409 12 10

Singapore HATeNBOeR-WATeR ASiA PTe LTD

OFFICe AND WAReHOuSe: 22 Boon Lay Way #01-57 Tradehub 21 609968 Singapore SW e [email protected] +65 6515 8021 www.hatenboer-water.com

AustraliaMARiNe PLANT SYSTeMS PTY. LTD.6/8 Redemptora RoadHenderson WA 6166Australia

T +61 (0)8 9410 0144F +61 (0)8 9410 0155e [email protected]

GCC CountriesUNiTeD TeCHNiCAL SeRViCeSPlot No. 3ESector MN-3 MusaffahAbu DhabiGCC Countries

T +971 4 339 27 55M +971 50 557 33 21e [email protected]

South KoreaDONG SUNG CO. LTD.#1725 century O/T 55-1Daeteon- 3Dong, Nam-Gu608-743 BusanKorea

T +82 51 610 1233F +82 51 610 1232 e [email protected]

SpaineCHO MARiNe SeRViCeS S.L.Calle Puig D'alaro 10 Bajos E-07015 Cala Major, Mallorca Spain

T +34 (0)971 400 213F +34 (0)971 405 873e [email protected]

ThailandTRiMAR eUROLUBe CO. LTD.108/10 Moo 6, NajomtienSattahipChonburi 20250 Thailand

e [email protected] +66 033 005 810F +66 033 005 814www.eurolube.net

United KingdomALTHAMSAnchor BuildingPenrod WayHeysham LA3 2UZUnited Kingdom

T +44 (0)1524 862010F +44 (0)1524 862011e [email protected]/hadex


More than 2000 units in

operation

In water since 1906

All systems are tested in

our workshop

Over 100 dedicated professionals

Fully equipped workshop

Risk assessments & Water analyses

Management plans and audits

Potable Water Courses

In-house engineering

and R&D department

Focus on quality

experience

Water Quality

consultancy

Worldwide services

24/7

Safe WaterFrom production to consumption

Green thinking

One stop shop

Worldwide stockpoints Spare parts &

Consumables

Reduction of your Cost of Ownership

Sustainable ISO 14001

energy saving solutions

Mothballing, Commissioning

& Start-up

Midlife updates

Maintenance & Overhaul

engineered integrated

systems


Custom Built SolutionsAccording your specifications

Hatenboer-WaterCustom Built Solutions

Made to measureNext to dedicated standard series, Hatenboer-Water also

provides systems that are fully made to measure in order to meet

owner demands. As specialist in water treatment, we are aware of

the challenges you face in your drinking water system, providing

enough water of good quality under the right pressure at the

correct temperature can be tough . With our broad experience and

knowledge we supply you with made to measure solutions that

are sound and have proven themselves on numerous platforms,

rigs and vessels. Solutions by Hatenboer-Water are designed with

sustainability and environment in mind. In many cases they result in

a lower total cost of ownership.

Combining

technologies

creates additional

security.

Combining technologiesIn larger water systems or due to difficult

con ditions, one disinfectant technology

often is not enough. By combining

technologies additional security will be

created. Hatenboer-Water can help you in

selecting the best available technologies

for your vessel or rig, keeping in mind the

regulations of the flag state or country you

are operating in.

Plug and playThe required equipment for your application

is fully skid built. The units are engineered

into detail including 3D CAD drawings,

pre assembled, tested and ready to use.

As a consequence, you are assured to save

costs and time during installation on board.

Every unit meets the high Hatenboer-Water

standards and applicable customer

classification requirements.


Tailored to your conditionsIn addition to our heavy duty design of our systems, it is possible

to include several design options tailoring to the more extreme

demands rising from the vessel or rigs operating conditions:

• Arctic design Allowing you to operate under harsh conditions and feed water temperatures below 0°C.

• estuary design Extensive additional pre-treatment allowing you to operate near coast lines or river estuaries.

• explosion proof design For placement of the system outside the safe areas of your rig. Zone 1 / 2, EX / IECEX.

• Shock proof design Continuous water production even up to 20 G-force movements meeting navy requirements.

• eco design Your water maker equipped with an energy recovery unit. A design that stands for an environmentally friendly and energy saving operation.

• Regulations Skids designed according required regulations such as NiPH, NR 13, MCA, NORSOK, IEC, MODU and any other applicable regulations.

• Owner specifications Tailored to meet owners design specifications and owners preferred vendor list for key components.

• Containerised For easy and quick sheltered installation.

Site-specific design

Whether it is a new or existing rig or ship,

Hatenboer-Water will design a system ideal

for your circumstances.

Your system designed according to the high

Hatenboer-Water standards, based on more than

hundred years of maritime experience.


Hatenboer-Water RO desalination systems Desalination by reverse osmosis (RO) has proven to be a reliable

and economical means of drinking water production.

Hatenboer-Water offers a wide range of high quality water makers.

Your maritime or offshore demands and conditions are met in our

proven and heavy duty design. Hatenboer-Water RO’s are easy to

install, easy to operate and continuously provide a perfect quality of

drinking water on board. Next to skids that are fully made to measure

in order to meet owner demands, Hatenboer-Water also provides

dedicated standard water maker series.

Advantages reverse osmosis

For the production of water on

board, reverse osmosis has

proven to be the best technology

available over the last decade.

A reverse osmosis water maker

produces good quality water

which requires limited post

treatment.

The energy consumption is

relatively low and the required

maintenance is limited and can

be performed by the crew.

All these advantages result in

a low Total Cost of Ownership for

your water production.

Worldwide, hundreds of

Hatenboer-Water RO seawater

desalination systems are in

operation on ships and offshore

installations.


Unique features of RO Extensive pre-treatmentAll RO systems are equipped with a high

capacity pre-treatment system being an

efficient multimedia filtration and high

load cartridge filter for the removal of

particles such as sand and mud. This

results in limited fouling of the membranes,

providing optimal water production and low

operational costs.

Energy saving membranesTo guarantee long-lasting and trouble-free

desalination of seawater into fresh water,

the RO systems are designed with the latest

energy saving membranes.

Cleaning in Place unit By regular cleaning of the membranes it

is possible to extend their lifespan

significantly. For this purpose RO’s are

equipped with an integrated CIP system.

Custom Built two stage RO

NIPHcompliance

NR13compliance

NORSOKcompliance


Hydrophore UnitsFrom the bridge to the galley and from all cabins to all safety

connections on all decks. Our hydrophore units provide water on

these places with the required pressure. Hatenboer-Water is

familiar with the circumstances on board and can guarantee you

a sufficient supply of water. The configuration of the skids can

consist of high quality tanks, automatic control switches,

a pressure gauge, a pressure relief valve and all necessary valves,

manifold and piping. The system can be equipped with:

• normal or self priming hydrophore pumps

• pumps in cast iron, bronze or stainless steel

• pressure vessels, standard or diaphragm, in galvanised steel or stainless steel

Hot and Cold Water ModulesHatenboer-Water can provide your complete drinking water and

hot water supply on board. From production to tap point. Plug and

play hot and cold water modules including interconnecting piping,

wiring, pumps, disinfection, hydrophore, cartridge filters and

hot water calorifiers. Like all skid built solutions, you just have to

connect the mains piping and electricity supplies. If requested we

can integrate the required disinfection technology into the skid for a

small footprint. Naturally all equipment can be supplied as separate

items. As you can see, there is a reason why Hatenboer-Water is

regarded as a full service partner!

Maximum water

flow with sufficient

pressure.


Disinfection ModulesProviding the optimal solutions for

the toughest water disinfection challenges.

Challenges that you face on board, like

differences in water quality when bunkering,

temperature changes or old piping. Without

proper disinfection, water is likely to contain

dangerous pathogens or bacteria like

Legionella. At Hatenboer-Water we can

include high end disinfection technologies

in the fresh water generator skids or pressure

sets to save footprint and to ensure safe

water on board.

Due to our extensive experience with water

quality on board we are the perfect partner

for assessing the risks on board and

determining the appropriate equipment.

Three of our most effective and suitable

disinfectants are:

• Hadex® drinking water disinfectant

• Demitec® ultra violet disinfection

• LiquiTechTM copper/silver-ionisation

Details on these techno logies you can find

in the dedicated product chapters.

Always the right solution for your application

Hatenboer-Water carefully considers the

practical situation, target organisms

and site-specific properties of your

application to provide the right solution.

Fully integrated cold water module including disinfection

and filtration

24 | www.hatenboer-water.com 25 | www.hatenboer-water.com

1. Water DesalinationRO seawater desalination sytems for a reliable potable water production

For your reliable potable water production on board our RO seawater desalination systems are available in a wide range of capacities.

Besides the successful custom built systems Hatenboer-Water has developed standard reverse osmosis series for the maritime and offshore market. These standard water maker ranges are part of the proven Hatenboer-Water RO designs and will provide safe and reliable water for the ships crews under any circumstances.


1.1 Reverse Osmosis standard desalination systems p.26

Proteus SeriesCapacity: 36 - 100 m3

Oceanus SeriesCapacity: 8 - 24 m3


1.1 Reverse Osmosis Desalination systemsHatenboer-Water Standard Series

The Oceanus series covers a range of 8 - 24 m3 per day fresh water production and is intended for vessels with limited space for installation, such as tugs, support vessels, dredgers, unmanned platforms, merchant shipping etc. The Proteus series covers a range of 36 - 100 m3 per day fresh water production and is intended for offshore installations, such as jack-up drilling rigs, semi subs, drill ships, pipe lay vessels, accommodations, cattle ships, cruise ships, chemical tankers etc. The Proteus series offers a heavy duty offshore design, large production capacity, continuous and reliable operation all over the world.

D E S I G N

A S S E S S E D


1. Desalination

RO Oceanus seriesThe Oceanus series is intended for vessels with limited space for installation, such as tugs, support vessels, dredgers, unmanned platforms, merchant ships etc.

Durable design • Rigid steel coated base frame for easy installation • High pressure duplex stainless steel plunger pump for extended trouble free

operation• Automatic fresh flush and integrated chemical cleaning unit for long membrane

life time

ensured water quality • Product water dump at off spec quality • Product water monitoring and indication for water quality control

Optional features • Post-treatment equipment to preserve water quality• Cyclone separator for improved pre-filtration in coastal areas• Pre- and post-treatment backframe, saves installation time and costs

*Capacity based on a seawater temperature of 5 – 25°C @ 36.000 ppm TDS

For temporary solutions you can contact us for our

rental units offering a unique flexible solution against

minimum required time, effort and costs.

Model Capacity* Power Dimensions Weight Feed BSP (F) connection typesProteus m3 /day kW L (mm) W (mm) H (mm) Dry

(kg)Wet (kg)

Flow(m3/h)

Pressure (bar)

Inlet Fresh water inlet

Product Brine

DOS 40-2 8 7 800 750 1850 312 542 2,4 3 - 5 1” 3/4” 1/2” 1"

DOS 40-3 12 7 800 750 1850 326 564 2,4 3 - 5 1” 3/4” 1/2” 1"

DOS 40-4 16 7 800 750 1850 340 586 2,4 3 - 5 1” 3/4” 1/2” 1"

DOS 40-5 20 7 800 750 1850 355 609 2,4 3 - 5 1” 3/4” 1/2” 1"

DOS 40-6 24 7 800 750 1850 369 631 2,4 3 - 5 1” 3/4” 1/2” 1"


For temporary solutions you can

contact us for our rental units

offering a unique flexible solution

against minimum required time,

effort and costs.

RO Proteus seriesThe Proteus series covers a range of 36-100 m3/day fresh water production and is intended for offshore installations, such as jack-up drilling rigs, semi subs, drill ships, pipe lay vessels, accommodations, etc. The Proteus series offers a heavy duty design, large production capacity, continuous and reliable operation all over the world.

Heavy duty design • Rigid steel base frames for safe transport and easy installation • Duplex stainless steel high pressure manifolds for long life time

enhanced membrane life timeOur Proteus series are standard provided with:

• Large pre filtration surface and multimedia filtration for increased overall performance

• Conservative membrane design with low loads to minimise fouling• Automatic fresh flush system to prevent fouling at standby modus• Chemical cleaning unit for cleaning fouled membranes• Chemical conservation to preserve membranes in offline modus

ensured water quality • Product water dump at off spec quality• Product water monitoring and indication for water quality control

Optional features • Post treatment equipment, to preserve water quality• Sea water intake pressure control system

* Capacity based on a seawater temperature of 25°C @ 35.000 ppm TDS

Model Capacity* Power Dimensions Weight Feed Flange connection typesProteus m3 /day kW L (mm) W (mm) H (mm) Dry (kg) Wet (kg) Flow

(m3/h)Pressure (bar)

Inlet Product Brine

150# ASME B16.5

DPS 80-2 36 11 1800 1500 1800 800 1350 4 4 - 6 1 1/4” 1 1/4” 1 1/4”

DPS 80-3 55 11 1800 1650 1800 1100 1900 5,2 4 - 6 1 1/4” 1 1/4” 1 1/4”

DPS 80-4 70 15 2950 1400 2000 1300 2900 7 4 - 6 2” 1 1/2” 2”

DPS 80-6 100 22 2950 1400 2000 1350 3500 8,9 4 - 6 2” 1 1/2” 2”


1. Desalination

Hatenboer-Water is partner for ship and

rig operators, owners and shipyards in

the maritime and offshore industry.


2. Water DisinfectionKeeping water safety at the highest level

Water produced on board or bunkered is stored in drinking or technical water tanks. To keep the water safe to use for a longer period of time, it is necessary to disinfect the water; not only in the tanks, but also in the distribution system. you can find a wide range of disinfection technologies at Hatenboer-Water. each technology has its own specifications. Consult us to determine which disinfection technology suits you best.


2.1 Hadex® Drinking Water DisinfectantBased on sodium hypochloritep. 32

2.3 LiquiTech™

Copper/silver ionisationp. 42

2.2 Demitec® UVultra violet disinfectionp. 38

2.4 HWSiSSilver ionisationp. 44


2.1 Hadex® Drinking Water DisinfectantBased on sodium hypochlorite

Hadex® keeps drinking water in good condition. It is food grade and is approved as a continuous disinfectant in drinking water. Because of the overall action of Hadex® in water it disinfects the tanks, pipelines and all water fed equipment. It keeps your crew healthy.


2. Disinfection

Hadex® Food Grade Drinking Water Disinfectant

Highest standardsHadex® treatment is based on the proven and tested use of free chlorine in the preparation and final treatment of drinking water. Hadex® treatment combines this traditional practice with a number of important advantages, meeting the highest standards set for a drinking water disinfectant.

What standards to expect from effective drinking water disinfectant?• It should be food grade quality• It should be simple to apply• It should be immediately and easily soluble in water• It should be cost-effective per cubic metre of treated water• It should swiftly destroy any harmful organisms, and should remain active for

a sufficiently long period• It should have no adverse effects on water quality, and should not allow the water

to become corrosiveHadex® meets all these standards!

AdvantagesHadex® is not only a safe, effective and easily applied product, but compared with other products has even more advantages:

• it is easily stored• it has a very long shelf life:

• at least eighteen months under normal conditions (T=25°C). • at least three years if stored cool (T ≤6°C).

Other products have a shorter shelf life. For example, industrial sodium hypochlorite loses about 30% of its effectiveness after storage for 30 days at 30°C.

Part number Description0900-HDeX02,5 2,5 litre

0900-HDeX10,0 10 litre

0900-HDeX25,0 25 litre

DosingHadex® is ready for immediate use as delivered. Because it is a very pure, stable and safe product, it facilitates swift and accurate dosing. As it is a liquid product that mixes quickly and easily with water, it can be added simply through the filling pipe or through the tank opening. Hadex® starts disinfecting immediately, and the water is ready for consumption after a short period of only 30 minutes when applying the normal dosing.

Standard dosagesThere are three standard dosages for drinking water treatment in most situations. They all meet the standards laid down by international maritime authorities.

1 Normal dosage 1 litre Hadex® : 50,000 litres of drinking water intended for the treatment of water

that is clear and of a normal quality.2 extra dosage 1 litre Hadex® : 25,000 litres of drinking water intended for the treatment of water

that is of inferior or doubtful quality.3 High dosage (shock treatment) 1 litre Hadex® : 5,000 litres of drinking water Intended to be used under epidemic conditions and/or when it is suspected that the water might be infected. High

dosage should also be applied as an initial treatment for the disinfection of tanks and pipelines after repairs or renewals.

Hatenboer-Water offers a wide range of test kits to measure the amount of active Hadex® in the water. Of course, Hatenboer-Water can provide you with detailed information regarding dosing or you can download the application and material safety data sheet from www.hatenboer-water.com.

ApprovalsHadex® has been tested and approved by a number of (maritime) authorities in the Netherlands and abroad, including:

• Dutch Ministry of Health (Ctgb registration No. 9574N)

• Dutch Directorate General for Shipping and Maritime Affairs, Shipping Inspection, Division NSI (NL)

• DOT (UK)• NIPH (Norway)• NMA (Norway)• GL (Germany)• NATO

AvailabilityHadex® is available from a large number of suppliers, including ship’s chandlers and agents. Check out page 14 for stock points near you.

M L Ccompliance


Hadex® Dosing Units (HDU) The HDU's are proportional controlled, by use of pulse gene rating flow meters. All dosing units can be supplied to meet your own specifications. A major advantage of the Hatenboer-Water dosing units is that the standard packing is designed to be as a dosing container. Therefore safer and easy to use.

Secure your drinking water system with a fully automatic flow controlled Hadex® Dosing Unit. Dosing Hadex® is intended for the reduction and prevention of growth of bacteria, algae and other micro-organisms. Hadex® automatic dosing units are available for 10 and 25 litre Hadex® cans.

OptionsFor larger flows, especially in bunker systems electromagnetic flow meters are available too. These meters have no moving parts.

The dosing units can also be controlled on base of free chlorine concentration. For this an inline chlorine measurement unit is integrated. Contact our Sales Engineers for information on a possible configuration for your situation.

Hadex® dosing units are commonly used on three points in the fresh water system:

1. In the water maker product line2. In the fresh water bunker line3. After the hydrophore pumps (for re-chlorination of the distribution system)

Part number Volume Size flow-meter

Capacity nominal

Capacity maximal

Max pressure

Hot water

can type inch / mm

Qn m3/h @ ΔP 0,25 bar

Qmax m3/h @ ΔP 1 bar

bar

HDU10-1601-15C 10 ½” 1,5 3 16 •

HDU10-1601-20C 10 ¾” 2,5 5 16 •

HDU10-1601-25C 10 1” 3,5 7 16 •

HDU10-1601-30C 10 1¼” 5 10 16 •

HDU25-1601-15C 25 ½” 1,5 3 16 •

HDU25-1601-20C 25 ¾” 2,5 5 16 •

HDU25-1601-25C 25 1” 3,5 7 16 •

HDU25-1601-30C 25 1¼” 5 10 16 •

HDU25-1601-40C 25 1½” 10 15 16

HDU25-1602-50C 25 2” 15 30 16

HDU25-1604-65C 25 DN65 25 63 16

HDU25-0708-80C 25 DN80 40 100 7

HDU25-0708-100C 25 DN100 60 160 7

HDU25-0713-125C 25 DN125 100 250 7

HDU25-0713-150C 25 DN150 150 270 7

HDU25-0708-80e 25 DN80 50 150 7

HDU25-0713-100e 25 DN100 60 250 7

HDU25-0713-125e 25 DN125 100 270 7

Qmin is approximately 0,1 m3/h for all systems.

Key features• Easy to install• Compact installation • Flow controlled dosing units• Reliable, efficient and continuous

chlorination• Hadex® complies with many

regulations


2. Disinfection

Hadex® Digital Test KitsThe Hadex® Digital Test Kit is a compact, portable instrument to test key water quality parameters. Due to microprocessor technologies the chlorine level in your potable water is measured in the most effective and precise way. The testing results can be read immediately and gives you the opportunity to adjust (if necessary) your dosing programme at once.

Offshore proofThis test kit is the best way to analyse free chlorine in the drinking water disinfectant Hadex®. The photometer has been designed with particular attention to the environmental conditions encountered in maritime use. The keyboard and display are splash proof. The sample chamber, the most critical part of any photometer is fully sealed, so no water can penetrate into the electronic components. Cleaning is simple. The cuvette cover is used to eliminate the effects of ambient light. With the High Range reagents this test kit meets the conditions of the NIPH.

Contents• Instruments in carrying case• Batteries included• Round glass vials with lids• Powder reagents sufficient for 100 tests• Guarantee sheet• Certificate COC• Step-by-step instruction manual

Characteristics• Free & Total Chlorine - DPD no.1 and no.3• Range: 0 - 2 ppm• High range: 0 - 10 ppm

Part number Description0500-000008 Free Chlorine / Hadex® Digital Test Kit

Spare partsPart number Parameters Description Packing0525-DPD01POe Free Chlorine DPD no.1 powder reagents

0-2 ppm100 pcs

0525-000028 Free Chlorine (high range) DPD no.1 tablets 0-10 ppm NIPH

100 pcs

0525-000029 Total Chlorine (high range) DPD no.3 tablets 0-10 ppm NIPH

100 pcs

0525-197620 Cuvettes Glass vials, 10ml 12 pcs

All you need in one case! Of course a manual has been included.

Key features• Large backlit digital display• SMD-microprocessor technology• LED with long term light stability• Operating mode selection• Uses long-life reagent tablets• Carrying case


Hadex® Manual Test Kits: Checkit ComparatorThe Hadex® Checkit is a compact, colourimetric kit which is suitable to manually measure the amount of available Hadex® in your potable water. Hadex® is a food grade drinking water disinfectant. Supplied with a generous number of different colour scales, the kit provides the basis for a comprehensive, easy-to-use colourimetric analysis system.

Characteristics• Contains 30 tests• Unrestricted shipment• Testing range of 0 - 2 mg/ltr

Part number Description0500-HADeXTeSTKiT Hadex® Manual Test Kit

Spare parts Part number Spare parts0525-000028 DPD no.1 Free Chlorine high range tablets 0-10 ppm NIPH

0525-000029 DPD no.3 Total Chlorine high range tablets 0-10 ppm NIPH

145500 Sample Cells 10 ml with cap (10 pc)

146040 Colour disc for Hadex® Checkit comparator

Hadex® Test StripsThe Hadex® Test Strips are indicative and easy to use. Just dip a strip into water, move it back and forth 30 seconds and read by comparing the pads to the colour chart on the container. Technicians in the field can test many samples in only a few minutes and make immediate evaluations on-site.

Characteristics• Testing range 0 - 10mg/l• Free and Total Chlorine• Contains 50 tests

Part number Description0505-27450-50 Hadex® Test Strips (Free and Total Chlorine)

Key features• High accuracy• Tablet reagents with a minimum

guaranteed shelf life of 5/10 years• Easy operation and exact reagent

dosing

Key features• Accurate quick indication• Indicative and easy to use• No measuring, set-up, clean-up, or

chemical handling are necessary• Great for quick, on-site evaluations of

free and total chlorine levels


2. Disinfection

In larger systems or in difficult

conditions, one disinfectant technology

often is not enough. By combining

technologies additional security can be

created. Hatenboer-Water can help you

in selecting the best available

technologies for your ship, vessel or rig,

keeping in mind the regulations of the

flag state or country you are operating in.


2.2 Demitec® UVUltra violet disinfection

Sources for naturally clean water are becoming increasingly rare, making it one of the world’s most valuable resources. Without proper disinfection, water is likely to contain dangerous pathogens, including Cryptosporidium and Giardia.

Disinfection using ultraviolet (UV) light is a proven, chemical-free, environmentally friendly and sustainable method for killing pathogens and water infecting microorganisms. Hatenboer-Water specialises in providing the optimal solutions for the toughest water disinfection challenges.


2. Disinfection

Demitec® GammaLine (GS) UV SeriesThe GammaLine UV series is a low cost, high-quality and single lamp UV system. The ‘L-shape’ chamber design makes installation very easy. The design is kept as simple as possible so no tools are required to remove the lamp or quartz sleeve.

MountingThe UV unit can be installed both horizontally and vertically, so can be adapted to the specific situation on board. The GS series uses the low-pressure UV lamp technology and is available in different power configuration for different flows. This type of UV lamp is tuned to the most effective disinfection wave length (254 nm).

OptionsThe unit can be supplied with an UV sensor to have continuous monitoring of the disinfection power of the unit.

Key features• Easy installation• No tools needed for regular

maintenance• Stainless steel 316• Reliable and proven technology• 50/60 Hz available

Type Capacity Connected power

Connections Dimensions Chamber

Dimensions Controlbox

in m3/h@ 25 mj/cm²T10=90%

Watt BSP-M inch

L1 cm

L2 cm

M cm

W cm

H x W x D cm

GS110 1,0 20 1” 49,5 37,5 35 7,6 20 x 20 x 13

GS115 1,3 30 1” 49,5 37,5 35 7,6 20 x 20 x 13

GS120 1,9 40 1” 62 50 50 7,6 20 x 20 x 13

GS135 3,4 60 1” 62 50 50 7,6 20 x 20 x 13

GS145 3,9 60 1½” 102 90 90 7,6 40 x 40 x 20

GS175 7,0 150 1½” 102 90 90 7,6 40 x 40 x 20

GS 1125 14,0 200 1½” 102 90 90 7,6 40 x 40 x 20

Service space M

L1

L2

W


Type Capacity Connected power



in m3/h@ 25 mj/cm2

T10=90%

Watt L1 cm

M cm

W cm

H x W x D cm

BM120 3,0 40 1 ½”BSP(m) 62 50 11,4 40 x 40 x 20

BM135 6,0 60 1 ½”BSP(m) 62 50 11,4 40 x 40 x 20

BM145 7,0 60 1 ½”BSP(m) 108 150 11,4 40 x 40 x 20

BM175 12,0 150 1 ½”BSP(m) 108 150 11,4 40 x 40 x 20

BM1125 24,0 200 1 ½”BSP(m) 108 150 11,4 40 x 40 x 20

BL175 18,0 150 NW80 117 150 20,4 60 x 40 x 20

BL275 21,0 300 NW80 117 150 20,4 60 x 40 x 20

BL375 28,0 450 NW80 117 150 20,4 60 x 40 x20

BL475 56,0 600 NW80 117 150 20,4 60 x 40 x 20

BL575 61,0 750 NW80 117 150 20,4 60 x 40 x 20

BL675 63,0 900 NW80 117 150 20,4 60 x 40 x 20

BL775 65,0 1050 NW80 117 150 20,4 60 x 40 x 20

BL1125 37,0 200 NW80 117 150 20,4 60 x 40 x 20

BL2125 41,0 400 NW80 117 150 20,4 60 x 40 x 20

BL3125 56,0 600 NW80 117 150 20,4 60 x 40 x 20

Demitec® Betaline (BL/BM) UV SeriesBetaLine UV is a series of optimised ‘L-shaped’ units. The system is completely adaptable to your needs and design specifications. The BetaLine UV series uses low-pressure UV lamps (amalgam) which are available in different lengths, emitting a narrow band of wavelengths. The 254 nm wavelength is most critical for disinfection.

MountingThe ‘L-shape’ makes BetaLine UV system installation in existing or new pipelines very simple. The UV chamber, which can be installed in a main or bypass pipeline, vertically or horizontally, is able to turn 360° around the inlet axis. Smart design positions the maintenance end flange on top of the UV chamber, so BetaLine UV maintenance is very simple and requires only basic skills. The components are easily accessible for removal or replacement.

OptionsAll BetaLine UV systems can be adapted to years with a complete package of options:

• Electrical/manual anti fouling system to remove lime deposits from the quartz sleeves and UV sensor during operation. Even the smallest BetaLine UV unit can be equipped with an (electrical) anti-fouling mechanism.

• Flange connections according to DIN or ANSI up to 6”• UV sensor for continuous monitoring of the disinfection power of the unit• Change-over contact• Various power supplies (120V/230V/400V and 50 or 60Hz)• Working pressure standard 6 bar optionally up to 25 bar

Please contact our Sales Department for an offer or detailed information of a selected system.

Key features• Chemical free• Robust design• Stainless steel 316• Reliable and proven technology• Full control of disinfection

Service space M

L1

W

In

Out


2. Disinfection

NiPH Approved UV Disinfection (BLe and Kappa)When an offshore installation operates on the Norwegian continental shelf it needs to comply to the Norwegian regulations stated within the Norwegian Institute of Public Health (NIPH) Water Report. This guideline describes elaborately how to manage your water system, which materials may be used and more.

For disinfection with ultra violet, it is stated that UV units need to be approved and certified by the NIPH. As specialists in water treatment Hatenboer-Water saw the need for certification as disinfection is a barrier against bacteria, viruses and parasites. As a consequence Hatenboer-Water has certified a series of UV units. With the Demitec® UV BLE/KappaLine you comply with the NIPH regulations for offshore units.

The Demitec® UV BLE/KappaLine systems use specially developed low-pressure UV lamps and will emit a narrow spectrum of wavelengths. Most critical is the 254nm wavelength. To qualify for NIPH certification, all UV units include an absolute UV sensor which can be calibrated to provide a 4-20mA signal.

MaintenanceIntelligent system design makes the end flange easy to remove for quick, hassle-free access to all internal components. Only basic maintenance skills are required to remove or replace parts (UV lamps, wiper rings, quartz sleeves). Fouling of the quartz sleeves and UV sensor is prevented with an effective manual or electrically operated ‘anti-fouling mechanism’.

Type Capacity Power supply Connected power



m3/h BL(e) Watt L1 cm M cm W cm H x W x D cm

BMe1.250.C 3,5 230V / 50 or 60Hz 245 2"BSP / 2"ANSI / NW50 144,8 125 11,4 60 x 40 x 20

BMe1.250.D 4,3 230V / 50 or 60Hz 280 2"BSP / 2"ANSI / NW50 144,8 125 11,4 60 x 40 x 20

BMe1.250.e 4,7 230V / 50 or 60Hz 315 2"BSP / 2"ANSI / NW50 144,8 125 11,4 60 x 40 x 20

BMe1.250.F 5 230V / 50 or 60Hz 350 2"BSP / 2"ANSI / NW50 144,8 125 11,4 60 x 40 x 20

BLe2.130.D 6,4 230V / 50 or 60Hz 320 NW80 / 3"ANSI 965 595 20,4 60 x 40 x 20

BLe2.130.e 7 230V / 50 or 60Hz 360 NW80 / 3"ANSI 965 595 20,4 60 x 40 x 20

BLe2.130.F 7,5 230V / 50 or 60Hz 400 NW80 / 3"ANSI 965 595 20,4 60 x 40 x 20

BLe2.250.D 13,1 230V / 50 or 60Hz 560 NW100 / 4"ANSI 147,5 125 20,4 60 x 40 x 20

BLe2.250.e 14,4 230V / 50 or 60Hz 630 NW100 / 4"ANSI 147,5 125 20,4 60 x 40 x 20

BLe2.250.F 15,4 230V / 50 or 60Hz 700 NW100 / 4"ANSI 147,5 125 20,4 60 x 40 x 20

BLe4.250.C 34,9 230V / 50 or 60Hz 900 NW150 / 6"ANSI 147,5 125 20,4 60 x 60 x 20

BLe4.250.D 42,4 230V / 50 or 60Hz 1050 NW150 / 6"ANSI 147,5 125 20,4 60 x 60 x 20

BLe4.250.e 46,4 230V / 50 or 60Hz 1150 NW150 / 6"ANSI 147,5 125 20,4 60 x 60 x 20

BLe4.250.F 49,9 230V / 50 or 60Hz 1300 NW150 / 6"ANSI 147,5 125 20,4 60 x 60 x 20

K4XL18.130.C 72,9 400 V / 50 or 60Hz 2500 NW300 / 12"ANSI 75 x 70 75 40 120 x 80 x 40

K4XL18.130.D 88,6 400 V / 50 or 60Hz 2800 NW300 / 12"ANSI 75 x 70 75 40 120 x 80 x 40

K4XL18.130.e 96,9 400 V / 50 or 60Hz 3100 NW300 / 12"ANSI 75 x 70 75 40 120 x 80 x 40

K4XL18.130.F 104,2 400 V / 50 or 60Hz 3500 NW300 / 12"ANSI 75 x 70 75 40 120 x 80 x 40

Service space M

W

L1


2.3 LiquiTech™Copper/silver ionisation

It is known for centuries that copper and silver are strong disinfectants. Now it is possible to safely use these ions for disinfection in potable water applications. By means of ionisation, the ions are released when the water flows through a flow cell containing copper and silver electrodes. The ions are carried along in the flow, penetrating the biofilm and working inside the entire hot and cold water piping system.

This makes LiquiTech very suitable (recognised by the NIPH) for continuously combatting Legionella and other biological contamination in your water system or in systems where the existing water quality management measures are proving to be inadequate.


2. Disinfection

LiquiTech™

The LiquiTech system is comprised of a control unit and a flow cell. Each flow cell contains copper/silver electrodes. As water passes through the flow cell, a direct current is applied across the electrodes to stimulate the controlled release of ions. The rate at which the ions are released is automatically maintained by flow meter and a microprocessor-based control unit that is reliable and easy to operate.

The ions of the LiquiTech ionisation process are strong and potent biocides. The disinfection action is attributable to the positively charged copper and silver ions which form electrostatic bonds with negatively charged sites on microorganism cell walls and this will kill the microorganism. The accurate dose-rate control system maintains precise ion levels, providing residual protection and prevention of recontamination. It is this residual protection that makes the LiquiTech system superior in the challenging field of offshore.

use LiquiTech:• When a potable water distribution system is extensive.• When problems with Legionella occur frequently. • When piping on board is heavily corroded and filled with biofilm. • When piping systems requires a high concentration of chlorine dosing. • To ensure safe water on board.

Description Flow cell Capacity of flowtype m3 per day

S50 CLTF42 2

S100 QF7 3 - 8

S150 QF7 9 - 15

S300 QF7 16 - 30

S500 QF14 31 - 50

S750 QF14 51 - 80

S1000 QF14 81 - 100

Mounting instructionsFor an easy installation it is also possible to order a prefabricated wall panel with all piping, valves, flow meter and flow cell mounted on. This saves you installation time and ensures that the system is connected the proper way.

Key features• Easy to install • Flow proportional dosing• Effective in hot and cold water• EPA and CTGB approved disinfection

system• Recognised by the Norwegian NIPH• Most advanced disinfection

technology available


2.4 HWSiSSilver ionisation

The Hatenboer-Water Silver Ion Steriliser is a disinfection method for fresh water, approved by MCA. Silver was already used for its bacteriostatic effect in the old Roman times and has developed in to a modern technology used to dose the silver ions in controlled conditions. The silver ions prevent microbiological growth during storage of the fresh water in the fresh water tanks.


2. Disinfection

HWSiS15The Hatenboer-Water Silver Ion Steriliser is a disinfection method for fresh water, approved by MCA. Silver was already used for its bacteriostatic effect in the old Roman times and has developed in to a modern technology used to dose the silver ions in controlled conditions. The HWSIS-15D system is capable to treat max. 15 m3/h.

AdvantagesAn advantage of silver ions in the low concentration used is their safeguard for human and animal life. Silver ions have no effect on smell, taste, pH and colour of the water and have a long impact in the water storage and distribution system to avoid bacteriological contamination. The ion levels stay well below the maximum amount as specified by WHO and European directives.

CharacteristicsThe Hatenboer-Water HWSIS15D system is an easy-to-use, plug-and-play system, suitable for bulkhead mounting. It consists of a base plate containing the electrical control cabinet, the electrode chamber and accessories such as flow control valve, flow sensor, pressure gauge, shut off valves.

The dosing is controlled by an advanced micro processor system which makes sure that the right amount of silver is discharged depending on the total measured water flow. Operation is through a user-friendly menu.

OptionsOptionally a solenoid valve can be installed, for automatic shut off of the water flow in case of failure.

Part number Description DimensionsL x W x H (cm)

1008-AGSCOMP Silver Ion Steriliser HWSIS 15 m3/h, completely mounted on backplate

46 x 18,2 x 46

Key features• MCA approved• Easy installation• Reliable disinfection


3. Water DistributionThe right pressure for your water distribution

Hatenboer-Water delivers the pumps you need to keep the right pressure on the right place. From self priming pumps and frequency controlled centrifugal pumps to pumps for fire fighting up to complete hydrophore systems. Pumps can be executed in al kind of materials, like bronze, stainless steel or titanium. With our maritime and offshore expertise we select the best configuration for your situation. We stock all brands of pumps, including parts to keep your pumps running at all times.


3.2 Hydrophore VesselsIn hot water and pressure-boosting systemsp.52

3.3 Cat PumpsField-proven best value for SWRO desalination systemsp.56

3.4 Kemper ValvesBackflow preventersp.58

3.1 Grundfos PumpsRobust and energy efficient marine pumpsp.48


3.1 Grundfos PumpsRobust and energy efficient marine pumps

The high quality Grundfos pumps are considered as a valuable addition to the Hatenboer-Water product range: covering the engine room, general services and utilities, the Grundfos marine range includes robust pump systems for boosting, cooling, A/C and heating as well as pumps for fuel oil, lube oil, oily bilge and sludge. All Grundfos marine pumps can be adapted to meet individual customer requirements.


3. Distribution

TP(e) PumpsSingle-stage, centrifugal pumps electronically controlled

Technical dataFlow, Q max. 460 m3/h

Head, H max. 95m

Liquid temperature -25°C to +14o°C

Operating pressure max. 16 bar

ApplicationsCirculation of hot or cold water in:

• Heating systems• Domestic hot water systems• Cooling and air-conditioning systems.

Optional• Bronze pump housing• Twin-head versions

CR, CRi, CRN, CRT (e) PumpsCR, CRI, CRN, CRT, CRE range are multistage centrifugal pumps. The basic CR pump range is available in four different materials: cast iron, two grades of corrosion-resistant stainless steel, and all-titanium. There are 13 flow sizes, capable of producing up to 50 bar of pressure, and with a variety of shaft seals and rubber materials. The modular building system means you can choose a version to meet almost any pump requirement, handle difficult liquids and the most demanding operating conditions.

Technical dataFlow, Q max. 5-3000 m3/h

Head, H max. 5-120 m

Liquid temperature -5°C to 18°C

Operat. pressure max. 16 bar

ApplicationsThe pumps are suitable for liquid transfer in:

• Process water systems• Sea water systems• Pumping of acids and alkalis• Ultra filtration systems• Reverse osmosis systems

Characteristics• Integrated frequency converter to allow multi-speed operation and deliver optimal

pump performance• Non self priming• Temperature control with exposure to very high, low or fluctuating temperatures

Whatever the particular challenges of your installation – for example, limited space, earthquake risk, high altitude or certification issues – the CR range has all bases covered.

Key features• Reliable• Space -saving• Service-friendly• High corrosion resistance• Optimised for high effeciency and

reduced power consumption

Key features• Space-saving• Service-friendly • High corrosion resistance• Reliability and high efficiency • Standard dimensions according to EN

standards


Hydro MPC Pressure Boosting SystemsComplete pressure boosting systems

Flow, Q max. 720 m3/h

Head, H max. 160 m

Liquid temperature o°C to +7o°C

Operating pressure max. 16 bar

ApplicationsSuitable for pressure boosting in:

• Water supply systems• Water treatment systems• Fire fighting systems• Industrial plants

Se(V) PumpsHeavy duty submersible pumps

Flow, Q max. 88/s (315 m3/h)

Head, H max. 45 m

Liquid temp. o°C to +4o°C

Operat. pressure DN 65 to DN150

ApplicationsThe pumps are suitable for the following applications:

• Wastewater• Process water• Unscreened raw sewage

Optional• Motor operation control • Control and protection systems• Sensors for monitoring pump conditions

Key features• Cable plugconnection• Unique clamp assembly system• Single-channel and vortex impellers• Solids passage up to 100 mm• Minimum downtime• Low operating costs• Liquidless motor cooling• Unique cartridge shaft seal

Key features• Constant pressure• Simple installation• Low-energy• Wide range• Frequency controller


3. Distribution

Key features• Wide range• Compact design• Standard motor• Service-friendly• Various types of shaft seals depending

on liquid, temperature and pressure

Magna Circulation Pumps

ApplicationsCirculation of hot water heating and hot water systems

Options• Stainless steel pump housing• Twin-head versions• Wireless remote control, R100• Communication via GENIbus or LON

Charateristics• Wide range• Low noise level• Low energy consumption, Energy labeling: Class A• Automatic performance adjustment• Simple installation (no extra equipment or fittings required)• Safe selection

Made to Measure

Drinking water from the seaFor a project in Saudi Arabia, Hatenboer-Water has developed a water production and distribution installation for the production of 30,000 litres of drinking water per day from seawater. The system consists of a heavy-duty pre-filtration unit, two reverse osmosis installations, together with a neutralisation stage to make the seawater drinkable. In order to ensure that the water pro duced remains drinkable,the distribution system has been equipped with a Hadex® disinfection dosing unit and a Demitec® UV disinfection system; these are located after the hydrophore installation.

Pumping systemSelected for this application was a frequency controlled Hydro MPC-5 2 CRIE 10-9 hydrophore. Frequency control means that the chance of water hammer is minimised, and all users are ensured of water at the correct pressure and flow rate at all times.

ContainersBoth systems have been assembled and delivered in a single 20ft container. Thanks to the design and construction carried out by Hatenboer-Water, the water units are simple to operate and main tain.


3.2 Hydrophore VesselsIn hot water and pressure-boosting systems

A stable water supply and economical handling of drinking water are the core benefits of potable water expansion vessels.

Hydrophore vessels save valuable drinking water. However, in a pressure-boosting system the vessel stabilises also the pressure in the drinking water network. As there are no uniform standards. Hatenboer-Water selected a range of vessels that meet up the high offshore and maritime demands you need.


3. Distribution

Full Flow Through Membrane Tanks (up to volumes of 80 litres)Expansion Membrane vessels with fixed a gas cushion for drinking water systems.The airproof membrane is from a special butyl rubber and suitable for drinking water.Two connections enabling water to flow through the tank. The advantage is that there is no stagnant water.

Potable water expansion vessels in hot water systemsSave valuable drinking water in potable hot water systems. The expansion water is no longer lost through a safety valve, but is absorbed by the expansion vessel.

Potable water expansion vessels in pressure-boosting systemsStabilises the drinking water network and reduce the switching frequency. They can be installed at the low pressure and high pressure sides of a pressure boosting system. The mains pressure side is always to be coordinated with the water supply company.

ApprovalsAs there are no uniform standards, please observe the drinking water approvals for the individual countries with respect to the selection. These are decisive for the deployment of flowfresh fully flow-through or no flow-through expansion vessel.

• Drinking water inspection according to the rules of SVGW, ACS, PZH• CE design-tested according to PED/DEP 97/23/EC

MaintenanceThe expansion vessels are virtually maintenance-free. In general, it is sufficient to observe the flow pressure conditions before the expansion vessel and to check the pre-pressure at least every 5 years. It must always be smaller than the flow pressure. Otherwise, increased bag wear will occur. The A(U)F expansion vessels are equipped with a Hydrowatch HW that signals bag damage.

Characteristics• Steel, welded• Foot ring for upright assembly and easy transport• Easy mounting thanks to their convenient eyelets• All metallic parts in contact with water in stainless steel

Part number Type Flow P max Diameter (D) Height (H)

m3/h bar cm cm

0465-PWDO008 ADF 8.10 ½" 0,6 10 34,5 16,6

0465-PWDO018 ADF 18.10 ¾" 1,0 10 43 22,4

0465-PWDO025 ADF 25.10 ¾" 1,0 10 47,2 25,1

0465-PWDO035 ADF 35.10 ¾" 1,0 10 52,1 28

0465-PWDO050 ADF 50.10 1" 1,7 10 58,7 31,7

0465-PWDO080 ADF 80.10 1" 1,7 10 68,7 34,7

Key features• Slim cylindrical model• Flowfresh full flow-through• Hydrowatch for tightness control

of the bag • Endoscopic opening for internal

inspections


Conventional Membrane Tanks with integrated internal circulation (up to volumes of 3000 litres)Membrane vessels for large flows with adjustable gas cushion for drinking water systems. The replaceable airproof membrane is made from a special butyl rubber and suitable for drinking water. This version has a single connection on the underside of the tank. Factory equipped with ’flowjet’: flow-through, shut-off and discharge valve for internal circulation in the tank to prevent bacterial growth.

Potable water expansion vessels in hot water systemsSave valuable drinking water in potable hot water systems. The expansion water is no longer lost through a safety valve, but is absorbed by the expansion vessel.

Potable water expansion vessels in pressure-boosting systemsStabilises the drinking water network and reduces the switching frequency. Can be installed at the low pressure and high pressure sides of a pressure boosting system. The mains pressure side is always to be coordinated with the water supply company.

ApprovalsAs there are no uniform standards, please observe the drinking water approvals for the individual countries with respect to the selection. These are decisive for the deployment of flowfresh fully flow-through or no flow-through expansion vessel.

• Drinking water inspection according to the rules of SVGW, ACS, PZH• CE design-tested according to PED/DEP 97/23/EC

MaintenanceThe expansion vessels are virtually maintenance-free. In general, it is sufficient to observe the flow pressure conditions before the expansion vessel and to check the pre-pressure at least every 5 years. It must always be smaller than the flow pressure. Otherwise, increased bag wear will occur. The A(U)F expansion vessels are equipped with a Hydrowatch HW that signals bag damage.

Characteristics• Steel, welded• Foot ring for upright assembly and easy transport• Easy mounting thanks to their convenient eyelets• All metallic parts in contact with water in stainless steel

Part number Type Volume P max Diameter Height (H) Height (h)

Standard Flowjet RP 1 ¼"

DN 50 PN 16

DN 65 PN 16

litre bar cm cm cm

0465-00008 DT 100 100 10 48 85,6 6,5 •

0465-DT5200/10 DT 200 200 10 63,5 97,3 8 •

0465-000031 DT 300 300 10 63,5 127,3 8 •

0465-DT5400/10 DT 400 400 10 74 124,5 6,9 •

0465-DT500 DT 500 500 10 74 147,5 7 •

0465-DT600 DT 600 600 10 74 185,9 23,3 •

0465-DT800 DT 800 800 10 74 232,4 23,3 •

0465-DT1000 ø1000 DT 1000 1000 10 74 260,4 23,3 •

0465-DT1000 ø1000 DT 1000S 1000 10 100 200,1 16 •

0465-DT1500 DT 1500 1500 10 120 200,1 15,8 •

0465-DT2000 DT 2000 2000 10 120 246,1 15,8 •

0465-DT3000 DT 3000 3000 10 150 252 18,7 •

Other connections available upon request.

Key features• Slim cylindrical model• Flowfresh full flow-through• Hydrowatch for tightness control

of the bag • Endoscopic opening for internal

inspections• For large flows

ØD

H

h


3. Distribution


3.3 Cat Maritime High Pressure PumpsField-proven best value for SWRO desalination systems

With over 40 years of experience in the desalination industry, Cat Pumps has developed a reputation as the industry leader in high-pressure positive-displacement pumps. The extensive line of 316 and Duplex Stainless Steel pumps offer unsurpassed corrosion-resistance, strength and long life, even in the harshest environments. For this reason Hatenboer-Water added Cat pumps to their range of products.


3. Distribution

Cat High Pressure PumpsThe Triplex High Pressure Pumps from Cat Pumps is the Hatenboer-Water standard for our water makers. With an extensive line of 316 and duplex stainless steel pumps for unsurpassed corrosion resistance they are suitable for the heavy duty maritime environment.

The pump design provides easy field servicing requiring only standard tools, with parts worldwide easily available. With field-proven dependability in hundreds of applications around the globe, Cat Pumps provides the best value in the (maritime) industry.

Besides the wide standard range we can offer custom engineered systems, designed to meet your requirements.

For further information or for a quote kindly contact our Sales Department.

High Pressure Pumps Accessoires

easy Maintenance KitThe Easy Maintenance Kit is especially designed for your convenience. We have put two items in one kit to avoid unplanned shutdowns and maximise your profit: the efficient LPS Monitor and easy to monitor Crankcase Oil Indicator Drain Kit.

LPS MonitorPump repairs, expensive pump replacements, unplanned shutdowns and costly downtime, these are now all part of the past because the LPS Monitor alerts maintenance personnel of water leakage before the pump drive components are at risk. Without oxidation and increased oil viscosity, oil lubricity remains stable and keeps production running smooth.

Crankcase Oil Indicator Drain KitThe Crankcase Oil Indicator Drain Kit simple monitors oil level at-a-glance with the smartly designed 360° indicator shield. Conveniently monitor oil when existing bubble gauge is obscured.

Part number Description Fits pump models0421-000126 Complete Easy Maintenance Kit Pumps 1520 - 6041

0421-000100 Separate LPS Monitor Pumps 1520 - 3841

0421-000057 Separate Crankcase Oil Indicator Drain Kit

Pumps 1520 - 6041

Key features• Continuous duty• Easy maintenance• Proven dependability • High pressure pumps available in

SS 316 and Super Duplex• Cost-effective pump to achieve

high-efficiency• Spares with short delivery time

available• ATEX certification on request

Key features• Avoid unplanned shutdowns• Easily monitor your pump unit • Monitor crankcase oil level at-a-glance • Improve pump maintenance

management processes• Easily drain crankcase oil for

scheduled maintenance• Indicator shield can rotate 360° for

optimal viewing


3.4 Kemper ValvesBackflow preventers

Water is distributed throughout the ship and is not only consumed by the crew, but also by water fed systems. Every time the water is used the risk of chemical/biological contamination of the complete system grows. Kemper backflow preventers are a basic safeguard of your water system, although a simple solution it is many times ‘the forgotten valve’.


3. Distribution

Backflow Preventers BA + eAAll outlets and systems in the potable water system need to be connected in a safe way to prevent pollution. The type of connection depends on the health risk category of the water inside the connected outlet or system. If the colour, taste, temperature or purity changes, the correct way of connection needs to be selected.

Some examples are: dish washer, washing machine, potable water connection to oil separator, waste water treatment, window wash system, etc. Shipbuilding engineers have a challenging task in keeping water safe for crews and passengers.

The “NIPH Water Report 120-Safe, Sufficient and Good Potable Water Offshore” refers to the EN 1717. It classifies five water categories which describe the quality of the water that is present in different types of outlets and connected systems.

Category 1 is water for human consumption direct from the potable water system. Category 2 is water suitable for human consumption, but it is treated like heating or cooling (coffee maker, ice cube maker). The higher the category, the higher the risks and the requested protection.

The description of category 5 is a fluid, representing a health hazard to humans through the presence of microbiological or viral pathogens of transmittable diseases (infection, mortal danger).

The most common protections are the EA and the BA. The EA (antipollution check valve) is allowed till category 2 and the BA (backflow preventer) till 4. EN 1717 has to be followed for correct installation. EA with valve and BA with cut-off valves and strainer.

Valves are made of gunmetal and can be supplied with various connection (DIN, JIS, ANSI flanges or NPT/BSP threaded connections) with sizes starting from DN15 up to DN150.

Please contact our sales department for a quote and detailed information.

Key features• Corrosion free gunmetal• All connections available• Strainer and valves integrated• Shortest build in length• 4ms certified

Part number Description Material Connections DiN ANSi JiS

Stainless steel

Gunmetal Male thread

Flange DIN 2501

NPT male thread

Flange B16.5 150#

Flange 10K

Flange 16K

eA Anti-pollution check valve sizes

145 1G DN15, DN20, DN25, DN32, DN40, DN 50 • •

145 18 DN15, DN20, DN25, DN32, DN40, DN 50 • •

145 97 DN15, DN20, DN25, DN32, DN40, DN 50 • •

145 96 DN25, DN32, DN40, DN50 • • •

BA Backflow preventer sizes

360 0G DN25, DN32, DN40, DN50, DN15 • •

360 18 DN25, DN32, DN40, DN50, DN15 • •

360 ANSi DN25, DN32, DN40, DN50 •

360 JiS DN25, DN32, DN40, DN50 • • •

360 97 DN25, DN32, DN40, DN50 • • 361 01 DN65, DN80, DN100, DN150 • •

361 02 DN65, DN80, DN100 • •


4. Water FiltrationEfficient, economic and reliable

It is important to remove sand, grit, silt, rust, colour, odour and other impurities to protect the water system from contamination which can be a threat for the general water safety. It will also prevent damaging or clogging of water using equipment downstream what as a consequence saves a lot of maintenance. Not only for large water flows, but also for small scale applications Hatenboer-Water has the appropriate filter system. A wide range of filter cartridges: 1 – 800 microns, surface and depth type, with or without activated carbon, selected materials and in various sizes.


4.3 Filter Mediavarious filter applicationsp. 70

4.1 Filter HousingsCartridge / bag filters p. 62

4.2 Filter CartridgesRemoval sediment and contaminationsp. 66


4.1 Filter HousingsDurable and easy to service filtration

Hatenboer-Water supplies different cartridge filter housings for different applications. Filter housings that can be used for single point or in series, for small or more demanding large water flows. All housings are selected for their durability and all are easy to service. Material used varies from stainless steel 316L to durable plastics. evidently, all filtration housings are fitted to hold all types of cartridges.


4. Filtration

Hatenboer-Water Demitec Cartridge Filter HousingsThe Hatenboer-Water Demitec Cartridge Filter (HDCF) housing is an effective, well designed and easy in use housing. Constructed of 316L stainless steel and designed for easy access and quick change out of the filter cartridges, the HDCF fits perfectly in a maritime environment. The HDCF filter housing can be applied as fine filter or as activated carbon fine filter, depending on the type of filter cartridge is used. A various range of accessories and connections is available to match your requirements.

Part number Capacity Dimensions Pressure Connections fine filter activated

carbon W x H max* DIN

m3/h m3/h mm bar

HDCF 3-10 3 1,5 262 x 533 10 2” BSP (m)

HDCF 3-20 6 3 262 x 788 10 2” BSP (m)

HDCF 3-30 9 4.5 262 x 788 10 2” BSP (m)

HDCF 3-40 12 6 262 x 1334 10 2” BSP (m)

HDCF 5-20 10 5 300 x 824 10 2” BSP (m)

HDCF 5-30 15 7.5 300 x 1079 10 2” BSP (m)

HDCF 5-40 20 10 300 x 1334 10 2” BSP (m)

HDCF 7-30 21 10.5 327 x 1082 10 2” BSP (m)

HDCF 7-40 28 14 327 x 1337 10 2” BSP (m)

HDCF 10-30 30 15 470 x 1170 8.5 DN80

HDCF 10-40 40 20 470 x 1425 8.5 DN80

HDCF 12-30 36 18 470 x 1191 8.5 DN80

HDCF 12-40 48 24 470 x 1446 8.5 DN100

HDCF 15-40 60 30 520 x 1463 6 DN100

HDCF 18-30 54 27 520 x 1211 6 DN100

HDCF 22-40 88 44 568 x 1379 6 DN100 *Higher pressure rating available on request.

X100 Filter HousingsThe X100 standing filter housings are strong, lightweight and economical. Resistant to a wide range of chemicals for a wide range of industrial applications, the X100 filter is considered to be a heavy duty sediment filtration system.

The X100 has a 'clean wall' design, a smooth interior surface that allows faster, easier manual cleaning or in place flushing.

The Polyloc® seal point of the filter bags and the cartridges filters creates a positive seal and eliminates the chance of fluid by-pass.

Because the X100 is top loaded with a specially developed threaded lid and gasket, filter bags & elements can be changed without additional tools for tightening.

Designed to accept either a bag filter or a cartridge filter, the X100 filter housing allows you to choose the filter media and construction to precisely fit your filtering needs.

Part number Description Max. Capacity Dimensionsm3/h L x W x H (cm)

0209-FHX100B X100 Filter bag housing 12 22,5 x 20,8 x 82

0239-FHX100C X100 Filter cartridge housing

12 22,5 x 20,8 x 82

Key features• Quick change of filter cartridges• Stainless steel 316 quality for potable

water systems• Applied as fine, carbon or duo filters• High flow• Made to measure also possible

Key features• High capacity sediment filter• X100 bag and cartridges are FDA

compliant • Lightweight and chemically resistant • No fluid by-pass• Easy access for manual cleaning or

in-place flushing


Filter Housings Model 113 & 213

Filter Model 113 The Hatenboer-Water filter house type 113 is suitable for a wide range of filter cartridges to remove impurities which find their way into the water supply. Ideal for domestic and general purpose applications. The housing contains a self supporting polypropylene head, a polyamide ring nut and a filter vase. This design makes maintenance quick and easy, the filter can be replaced by simply unscrewing the ring.

The head has a built-in pressure release valve and is equipped with threaded brass connections for optimal quality and insurance of your connection. Material for food purpose, according to CE rules.

Transparent and non transparent filter vases of 10” and 20” are available.

Part number Description Connection material

Ring material

Cartridge length

Max pressure

BSP brass inch bar

0215-1137509A Filter Model 113 Transparent

¾” SAN 10” 8.6

0215-1137509C Filter model 113 White

¾” PP 10” 8.6

0215-1131020B Filter Model 113 Transparent

1” PC 20” 8.6


1” PP 20” 8.6

Filter Model 213 The Hatenboer-Water type 213 is fully plastic executed filter housing which makes it suitable for filtration of seawater or other corrosive media.

The Filter House type 213 has the same qualities and characteristics as filter house model 113.

Part number Description Connectionmaterial

Ring material

Cartridge length

Max pressure

BSP plastic inch bar

0215-2137509A Filter Model 213 Transparent

¾” SAN 10” 8.6


¾” PP 10” 8.6

0215-2131020B Filter Model 213 Transparent

1” PC 20” 8.6


1” PP 20” 8.6

Key features• Food grade materials• Compliant with EC legislation• Servicing completed in matter of

seconds• Built in pressure release valve• Three piece housing with self

supporting • Brass or plastic connection


4. Filtration

Key features• Pressure relief/bleed• Large capacity filtration• Complete polypropylene

Big Blue Filter HousingsThe Big Blue filter housings cover almost all of your large-capacity filtration needs, including high-flow and heavy-sediment applications. The extra large housing allows for greater cartridge capacity, reducing the number of vessels required for high flow-rate applications. The filter housing is constructed of durable reinforced polypropylene and is available in both 10" and 20" lengths.

The high-flow polypropylene cap is available with 1" or 1½" NPT inlet and outlet connections. Big Blue housings are compatible with a broad range of chemicals and are available with a pressure relief button. They accept a wide variety of 4½" diameter cartridges.

Big Blue filter housings meet all of your large capacity filtration needs, including high-flow and heavy sediment applications. Due to the extra large housing a higher cartridge capacity can be reached. The blue polypropylene caps are available with optional pressure relief button on the inlet to relieve pressure inside the housing when changing the filter cartridges.

Part number Description Connection Dimensionsinches H x D (cm)

0218-BB10100A Filter housing Big Blue 10” 1" 33,8 x 18,9

0218-BB10150A Filter housing Big Blue 10” 1½” 34,2 x 18,9

0218-BB20100A Filter housing Big Blue 20” 1" 59 x 18,9

0218-BB20150A Filter housing Big Blue 20” 1½” 60,3 x 18,9

Single Bag / Cartridge Filter Housings

The single bag and cartridge filter housing delivered by Hatenboer-Water is an all-plastic, rugged polypropylene construction for superior corrosion resistance. The glass fibre reinforced polypropylene withstands high-pressure and temperature combinations.

The filter has no metal components to rust, corrode or contaminate and is therefore ideal for seawater filtration. The unit comes with a heavy duty sediment filter bag support made entirely out of polypropylene.

The filter housing can also house filter cartridges.

Part number

Description Weight Max pressure

Capacity Connection Dimensions

kg bar m3/h inches L x W x H (cm)

0236-F610041

HW Single bag filter housing

29 10 24 2"BSP 22,5 x 20,8 x 82

Key features• Quickly change filter due to

spin-off cover• Superior corrosion resistance• Suitable in reversed osmosis systems• Seawater filtration• Houses cartridges and bags


4.2 Filter Bags and CartridgesFor various applications

Hatenboer-Water supplies different high efficiency filter cartridges for process and potable water applications. From superior melt blown sediment filters to wound depth type cartridges. Consisting of 100% first class polypropylene or containing activated carbon. The selectivity ranges from 1 to 800 micron from nominal to absolute.


4. Filtration

Hatenboer-Water Activated Carbon Filter CartridgesDesigned for greater flow rates, the Hatenboer-Water Activated Carbon stackable cartridge filter offers an economical solution on both process and potable water applications. The string wound PP outer core protects your system from fine sediment particles.

Activated carbon (GAC) is integrated in the cartridge filter to improve the taste, odour and appearance of the water.

The Hatenboer-Water Activated Carbon cartridge filters can also be used for de-chlorination and are quick replaceable filter cartridges.

The HAC filters are easy to maintain and can be considered as economically high-capacity carbon filter.

Specifications• Wounded polypropylene with a 5 micron filtration grade• Injection molded polypropylene with integral snap fastening clips, inner and outer

core sealing rings • Premium hard quality coconut shell, low ash content, graded size activated

carbon

Part number Description Length Diameter Filtration grade

Max. capacity

inch mm micron m3/h

0210-HAC24870 HAC Filter cartridges

10" 70 5 0,5

Hatenboer-Water Melt Blown Sediment Filter Cartridges The Hatenboer-Water Melt Blown (HWMB) filter cartridge is the latest development in sediment filter cartridge design. Manufactured with a true graded density, these cartridges exhibit a high void volume that results in low differential pressure loss and an excellent dirt holding capacity when compared to similarly rated cartridges. Each cartridge is complete with an integral support for maximum strength. The superior structure remains integral even under severe operating conditions and furthermore the structure is less prone to media migration and breakthrough often found on other unsupported spun bonded products.

Part number Length Filtration grade Max. capacityinch micron m3/h

0201-HWMB10 10" 1, 5, 10, 20, 30, 50, 75, 100, 150 1

0201-HWMB20 20" 1, 5, 10, 20, 30, 50, 75, 100, 150 2

0201-HWMB30 30" 1, 5, 10, 20, 30, 50, 75, 100, 150 3

0201-HWMB40 40" 1, 5, 10, 20, 30, 50, 75, 100, 150 4

Key features• Sediment and activated carbon

filtration in one filter• Improves taste, odour and

appearance of water• Stackable and easily replaceable filter• Dechlorination capacity• Made of FDA approved materials• Suitable for high flow rates• Dual purpose filter cartridge

Key features• Low pressure loss • Suitable for fresh water and seawater

applications• Less prone to media migration• Materials meet US FDA Title 21 and

USP Class VI requirements• True grade sediment filter• 100% Polypropylene• Consistent reliable performance


Hatenboer-Water Carbon Block Filter CartridgesThe Hatenboer-Water Carbon Block (HWCB) filters offers an economical solution for the removal of taste, colour of odour and solids. The rigid block construction eliminates any potential bypass. The filters will not fluidise, therefore maximising the effectiveness of the carbon media.

inner core An acid washed, high purity coconut based carbon block

Outer core A double layer, spun bonded fiber pre-filter layer

For higher flows we advise to consider the HWCB Big Blue filters. These filters allow a higher flow and also provide more contact time between the water and integrated carbon block due to a larger diameter. This results in a deeper filtration.

Outside diameterHWMB 71,5 mm

HWMB Big Blue 117,0 mm

Part number Length Filtration grade Max. capacityinch micron m3/h

0210-HWCB10005 10" 5 0,5

0210-HWCB20005 20" 5 1

0210-HWCB30005 30" 5 1,5

0210-HWCB40005 40" 5 2

0210-BB010 10" 5 1,25

0210-BB020 20" 5 2,50

X100C Filter CartridgesThe X100C Cartridge is a steep pore gradient, depth filter designed to have a large dirt loading capacity. The cartridge measures 5.5" in diameter, with a length of 23.25", yielding a total cartridge volume of 500 cubic inches.

The design features a single open end that directs fluid from outside the cartridge in through the filter. A built-in handle on the cartridge top assists in seating and removing. The cartridge bottom is equipped with a polyseal end ftting to ensure a by-pass-free sealing without the need for double O-rings or flat gaskets. Fitting securely into the cartridge plate. It does not require springs, hold-down plates or center posts.

Part number Description Length Filtration grade Max. capacityinch micron m3/h

0206-X100C (micron)

Filter cartridge 23.25" 1, 5, 10, 25, 50, 75, 100 12

Key features• Dual Purpose; sediment filtration and

chlorine reduction• BE grade high purity coconut based

carbon block media• Polymeric and Elastomeric materials

meet US FDA Title 21 requirements• Cartridges have been tested and

certified to NSF 42• Effective carbon surface area

for excellent chlorine reduction characteristics

Key features• Large dirt loading capacity• FDA compliant• Polypropylene core is extremely

resistant to collapse, temperature effect, channeling and bypass


4. Filtration

X100B Filter BagsThe X100B bag filter is a heavy duty sediment filter measuring 6” diameter by a length of 20”. Specially designed for the X100B filterhousing it has 2 square feet of surface area, making it capable of handling a capacity of maximum 12 m3/h. The filter bag is fitted with the patented Polyloc® Ring that seals directly against the wall of the filter housing and eliminates the chance of fluid by-pass. The Polyloc® Ring sits directly against the basket collar for additional bag support.

Single layerRobust piece completely made from polypropylene.


0209-X100B (micron)

Filterbag material polypropylene felt

20" 1, 5, 10, 25, 50, 100 - 800 12

Filterbags with snap-ring For the Hatenboer-Water single bag filter housing there is a wide range of bag filters available with a special seal ring.

Snap-ring filter bags are manufactured to the highest standards. Materials must meet stringent specifications for filtration performance and media purity. The snap ring seal ring adapts easy into the filter housing.


0209-PO10P1 Filterbag material polypropylene felt

16" 1, 5, 10, 25, 50, 100, 200

20

0209-PO10P2 Filterbag material polypropylene felt

32" 1, 5, 10, 25, 50, 100, 200

40

Seawater Reverse Osmosis MembranesHatenboer-Water offers an wide range of (Seawater) Reverse Osmosis Membranes in a variety of configurations, materials and sizes. Based on our experience Hatenboer-Water offers high quality membranes for your seawater desalination process. The selected membranes offer the highest degrees of salt rejection and productivity reliability. A selection of our Seawater Membranes programme:

HydranauticsSWC4+, SWC4 MAX, SWC5 (optimal flow and rejection), SWC5 MAX, SWC5-LD (low biological and colloidal fouling), SWC6 (high flow) and SWC6 MAX membranes.

Dow FilmtecSW30-4040 Commercial Sea Water RO membranes.

TorayTM8020-400 and TMG10 membranes.

As specialists in reverse osmosis other brands are available on request. Please send your inquiry to our Sales Department. Furthermore, the Hatenboer-Water Service Engineers can support you with the replacement of the membranes on site.

Key features• On stock• > 99.8% nominal rejection • Highest combination flow,

rejection and boron rejection • High energy efficiency

Key features• High flow• High efficiency• Easy replacement• Low maintenance

Key features• Single-pass filtration test in

accordance with ASTM F795-88 procedure

• Heavy duty filterbag • High capacity


4.3 Filter MediaVarious filter applications

The varying needs in different areas and for different raw water types helped Hatenboer-Water to compile a wide range of water treatment media. The balanced range has been compiled during the years Hatenboer-Water assisted in assuring safe water on board. To remove suspended solids, to increase pH or to improve colour, taste and odour of your water. Depending on the purpose of the filtration, media as well as lifetime of chosen filter beds can vary.


4. Filtration

Filter Media Activated CarbonActivated carbon is a porous form of carbon which can be manufactured from a variety of carbonaceous raw materials. The Hatenboer-Water products are made from coconut shell or coal. The coconut shell based activated carbon produced by high temperature steam activation of specially selected coconut shell char.

Activated carbon ideal for removal of chlorine, chloramines, disinfection byproducts and other compounds which create colour, taste and odor.

Part number Type Base Size (mm) Packing Process0320-K08x16 HD301 Coconut,

Granular1-3 25 kg /

bagOur standard for drinking water treatment media

0330-K80x02 HDG 80 x 2

Coconut, Sticks

2 +/-0,2 25 kg / bag

Gas fase or specific water treatment applications

0330-K50x04 HDG 50 x 4

Coal, Sticks 4 +/- 0,2 25 kg / bag

Gas fase or specific water treatment applications

0340-K8x14ZAK HDG-AG-0,05 8x14

Coconut impregnated with silver, Granular

1-3 25 kg / bag

Drinking water treatment to inhibit the growth of bacteria within the carbon media

0340-K8x14POT HDG- AG-0,05 8x14

Coconut impregnated with silver, Granular

1-3 1,5 ltr Drinking water treatment to inhibit the growth of bacteria within the carbon media

Filter Media AnthraciteAnthracite is a selected, natural, hard and clean filter media. It is used in single- or in dual-layer filters for the purification of all kinds of water including potable-, waste-, sea-, brackish-, process- and swimming pool water. Anthracite will not release any SiO2 to the water.

Part number Description Size (mm) Packing0300-HYDROK1N Filter anthracite type K1 0,8-1,6 25 kg / bag

0300-HYDROK2N Filter anthracite type K2 1,4-2,5 25 kg / bag

Filter Media eWT CompoundEWT is a harmless granular alkaline filter material with a high purity of calcium carbonate. Because of its micro-crystalline structure, it is superior to ordinary lime stone.

EWT compound is highly suitable as media for neutralising / mineralising filter installed after the RO watermaker or evaporator. The compound will re-harden and neutralise corrosive product water, resulting in protection the piping and installations against corrosion. It will also improve taste and appearance of the water. The EWT Compound reacts by slowly dissolving in the water.

Application:• CO2 removal, pH correction and remineralisation of soft water• Remineralisation of distilled and/or RO water• Improving taste and appearance of fresh water

Part number Description Size (mm) Packing0300-eWTJUR25 Granular alkaline filter 1,0-2,0 25 kg / bag

Key features• Absorption of organic compounds• Improvement of odour and taste• Dechlorination • Hydro Carbon Removal

Key features• Purification of all kinds of water• High filtration capacity

Key features• High quality product• Suitable for any alkaline filter• Prevent corrosion of piping• Unlimited shelf life• Harmless• Improves water quality• NIPH approved


Dolomite MineralsDolomite is a natural mineral which is formed by presence of both calcium and magnesium in limestone.

The compound is highly suitable as media for neutralising / mineralising filter installed after the RO watermaker or evaporator. It is commonly used for filtration and processing drinking water: to increase the pH value of the purified water after reverse osmosis system. While the water is strained from top to bottom in the filter, dolomite mineral dissolves and provides natural minerals to water such as calcium, magnesium and carbonate.

Dolomite Compound is applicable for:• CO2 removal, pH correction and remineralisation of soft water• Remineralisation of distilled and/or RO water• Removal of iron and manganese• Improving taste and appearance of fresh water

Part number Description Size Packingmm

0300-DOLOHAK1 Calcium carbonate (CaCO₃) + Magnesium carbonate (MgO)

2,5 – 5,0 25 kg / bag

Sand and GravelHatenboer-Water Filter Sand and Gravel is a 100% natural silica through an elaborate refining process, together with constant quality control, elevated to a top quality media – washed and heated, free of clay, dust organic matter or any other contamination.

Ideal for filtration of seawater, potable water, groundwater, swimming pool, waste water and sewage water.

Part number Component Size (mm) Packing

0310-0,4/0,8 Filter Sand 0,4 – 0,8 25 kg / bag

0310-0,7/1,25 Filter Sand 0,7 – 1,25 25 kg / bag

0310-1,5/2,5 Filter Gravel 1,5 – 2,5 25 kg / bag

0310-2/4 Filter Gravel 2 – 4 25 kg / bag




Cation/Anion Mixbed ResinMixed bed resins can be used for all applications requiring totally demineralised water. The resins consisting of a 1:1 chemically equivalent mixture of a strong base anion exchange resin and a strong acid cation exchange resin.

The NM-60 resin can be regenerated once saturated, while the MR-20 is a more economical non-regenerable mixed bed resin. Both resins are directly ready for use.

Part number Description Regeneration Packing0350-000001 MR-20 Mixed bed Resin No 25 ltr bag

0350-NM60 NM-60 Mixed bed Resin Yes 25 ltr bag

Key features• High quality• Suitable for alkaline filters• Prevent corrosion of piping• Presence of calcium and magnesium • Improves water quality• Unlimited shelf life• Natural product• NIPH approved

Key features• Sanitised material• Sizes to all international standards• 100% natural silica

Key features• Produces demineralised water• Water quality < 1 μS/cm • Free of silica and of carbon dioxide• Ready to use


4. Filtration


5. Water ConditioningCleaning and conditioning

Hatenboer-Water offers a complete line of reliable, high quality, cost effective water treatment products. Conditioning the water can vary considerably from merely removing chlorine from tap water to altering the pH, chlorine dosing for sewage treatment systems or swimming pools, preventing corrosion. We supply products all dedicated to condition your water. Furthermore you find membrane related chemicals such as bio degradable antiscalants and cleaning chemicals products to optimise the desalination process and minimise operational costs.


5.3 ChemicalsFor water treatmentp. 82

5.4 DemineralisersWater conditioningp. 86

5.1 Neutralising FilterspH correctionp. 76

5.2 Automatic Dosing UnitsAutomatic chlorinationp. 78

5.5 Water Softenersextend the lifetime of hot water equipment on boardp. 88


5.1 Neutralising FiltersAvoid corrosion in fresh water system

Water with a low pH value, such as product water of desalination plants (both evaporators and Reverse Osmosis water makers), is often corrosive and tasteless. The Hatenboer-Water Neutralising and Mineralising (HDN) filters are especially fitted for the conditioning of product water. As a result, the water is no longer corrosive and, when used for drinking, a natural taste is added to the water.



Neutralising FiltersThe Hatenboer-Water Neutralising and Mineralising (HDN) filters for the conditioning of product water from desalination installations. It improves taste and avoids corrosion in your fresh water system. Hatenboer-Water offers a wide range of neutralising/mineralising filters.

Water with a low pH value, such as product water from a evaporators or Reverse Osmosis water maker, is often corrosive and tasteless. This so-called ‘acid condition’ is due to the presence of free carbonic acid gas (CO2) and lack of natural minerals.

To make this water neutral or slightly alkaline, it should be neutralised or mineralised. To ensure the complete removal of CO2, the water will be filtered through a bed of neutralising filter media, named EWT Compound.

In the neutralisation process, CO2 reacts with EWT compound and natural bicarbonates are formed. As a result, the water is no longer corrosive and a natural taste is added to the water.

PipingThe HDN filters are supplied with a complete set of piping, including six ball valves for operating the complete filter process; backwashing, flushing and draining the filter.

MaterialThe HDN filter houses are available in several materials executions and designs:

• Glass-reinforced plastic• High quality steel with polyester coating• Stainless steel

Design Designed according to the Norwegian NIPH Regulations and/or additional CO2 dosing system is also available on request.

Part number Capacity Capacity Filling gravel / eWT compound

m3/day m3/h kg

HDN-10 10 0,5 25 - 100

HDN-20 20 1 25 - 150

HDN-30 30 1,5 25 - 200

HDN-40 40 2 25 - 225

HDN-50 50 2,5 25 - 250

HDN-75 75 3,5 50 - 300

HDN-100 100 5 75 - 350

HDN-150 150 7,5 75 - 450

HDN-200 200 10 150 - 500

HDN-250 250 12,5 150 - 600

Key features• Mineralising your water• Avoiding corrosion

in the fresh water system• pH correction• Natural taste


5.2 Automatic Dosing UnitsReliable, constant and easy conditioning of your water

Secure your drinking water system with a fully automatic flow controlled dosing unit. The Hatenboer-Water dosing units are proportional controlled, by use of pulse generating flow meters. A major advantage of the Hatenboer-Water dosing units is that the standard packing is designed to function as a dosing container. Therefore safer and easy to use.



Hadex® Dosing Units (HDU) The HDU's are proportional controlled, by use of pulse gene rating flow meters. All dosing units can be supplied to meet your own specifications. A major advantage of the Hatenboer-Water dosing units is that the standard packing is designed to be as a dosing container. Therefore safer and easy to use.

Secure your drinking water system with a fully automatic flow controlled Hadex® Dosing Unit. Dosing Hadex® is intended for the reduction and prevention of growth of bacteria, algae and other micro-organisms. Hadex® automatic dosing units are available for 10 and 25 litre Hadex® cans.

OptionsFor larger flows, especially in bunker systems electromagnetic flow meters are available too. These meters have no moving parts.

The dosing units can also be controlled on base of free chlorine concentration. For this an inline chlorine measurement unit is integrated. Contact our Sales Engineers for information on a possible configuration for your situation.

Hadex® dosing units are commonly used on three points in the fresh water system:

1. In the water maker product line2. In the fresh water bunker line3. After the hydrophore pumps (for re-chlorination of the distribution system)

Part number Volume Size flow-meter

Capacity nominal

Capacity maximal

Max pressure

Hot water

can type inch / mm

Qn m3/h @ ΔP 0,25 bar

Qmax m3/h @ ΔP 1 bar

bar

HDU10-1601-15C 10 ½” 1,5 3 16 •

HDU10-1601-20C 10 ¾” 2,5 5 16 •

HDU10-1601-25C 10 1” 3,5 7 16 •

HDU10-1601-30C 10 1¼” 5 10 16 •

HDU25-1601-15C 25 ½” 1,5 3 16 •

HDU25-1601-20C 25 ¾” 2,5 5 16 •

HDU25-1601-25C 25 1” 3,5 7 16 •

HDU25-1601-30C 25 1¼” 5 10 16 •

HDU25-1601-40C 25 1½” 10 15 16

HDU25-1602-50C 25 2” 15 30 16

HDU25-1604-65C 25 DN65 25 63 16

HDU25-0708-80C 25 DN80 40 100 7

HDU25-0708-100C 25 DN100 60 160 7

HDU25-0713-125C 25 DN125 100 250 7

HDU25-0713-150C 25 DN150 150 270 7

HDU25-0708-80e 25 DN80 50 150 7

HDU25-0713-100e 25 DN100 60 250 7

HDU25-0713-125e 25 DN125 100 270 7

Qmin is approximately 0,1 m3/h for all systems.

Key features• Easy to install• Compact installation • Flow controlled dosing units• Reliable, efficient and continuous

chlorination• Hadex® complies with many

regulations


Potable Water Dosing UnitsThe Potable Water Dosing Unit is designed to prevent and stop corrosion in potable water systems. Corrosion does not only cause “brown” water out of taps and reduction of internal piping diameters, it is also a breeding ground for all kind of bacteria, as e.g. Legionella.

Therefore it is important to prevent corrosion in order to have clean and safe drinking water. The Potable Water Dosing Unit operates completely automatic by use of a metering device which controls this dosing pump proportionally to the flow.

The Hatenboer HW Stabiliser 445+ is an approved chemical for application in drinking water systems. It is packed in standard 25 litre poly cans. Preferably the Potable Water Dosing Unit is installed directly downstream the potable water hydrophore pumps and upstream the hydrophore tank.

Technical data:

Frame Powder coated steel

Power Supply 230V/50-60Hz

Power Consumption 22 W max

Alarm available Low level

Part number Size Flowmeter

Capacity Nominal

Capacity Maximal

inch / mm Qn m3/hour @ ΔP 0,25 bar

Qmax m3/hour @ ΔP

PDU25-1601-25C 1” 3,5 5

PDU10-1601-30C 1¼” 5 10

PDU25-1601-40C 1½” 10 15

PDU25-1602-50C 2” 15 30

PDU25-1604-65C DN65 25 50

Qmin is approximately 0,1 m3/hour for all systems

Key features• Prevent and stops corrosion• Approved for drinking water systems• Flow controlled dosing units• Compact installation• Easy to install



Hatenboer-Water provides all water

conditioning products you need!


5.3 Chemicals for stabilising, cleaning or anti scalingDrinking, swimming and waste water

Hatenboer-Water has a range of high performance reverse osmosis chemicals include RO membrane cleaners and detergents, scale inhibitors and antiscalants, corrosion inhibitors, biocides, antifoulants, de-chlorinators and flocculants. To ensure that such closed circuit systems operate at optimum efficiency it is essential that the correct water conditions are maintained. This can be achieved using carefully selected products designed specifically for such closed systems. Our (biodegradable) products offer several key performance benefits!



Chlorinating Tablets TS70AquaChlorine TS-70 is a high quality calcium hypochlorite in 20 gram tablet, with an available active chlorine content of 70%.These tablets are suitable for disinfection/ treatment of soft and medium hard water. TS-70 is mainly applied in the maritime field for the treatment of waste water, sewage systems, sanitary systems and swimming pools.

DosingOne tablet contains 14 gram of active chlorine. A 20 gram tablet increases the chlorine content of 1 m3 water with 10 mg.

Part number Description Size Packing0900-TS70/20 Active chlorine tablets 20 gram Ø 32 mm 10 kg bucket

Chlorinating Tablets TS90AquaChlorine TS-90 is a high quality trichloroisocyanuric acid in 20 and 200 gram tablets, with an available active chlorine content of 85-90%. These tablets are suitable for disinfection/ treatment of all types of water, but most particular for hard water due to it's neutral pH effect on the water. TS-90 tablet is mainly applied in the Maritime field for the treatment of waste water, sewage systems, sanitary systems and swimming pools.

DosagingFor day to day operation under normal conditions a dosage of thirty 20 grams tablets or three 200 grams tablets per 100m3 is advised.

Part number Description Size Packing0900-TS90/20 Active chlorine tablets 20 gram Ø 32 mm 10 kg bucket

0900-TS90/200 Active chlorine tablets 200 gram Ø 78 mm 10 kg bucket

Sanuril115® Chlorinating TabletsSanuril chlorination tablets provide a patented disinfecting agent formulated for waste water treatment applications. In addition to chlorine, Sanuril tablets now contain an added active ingredient which releases bromine, another halogen used extensively for disinfection. The Sanuril tablet is mainly applied in the maritime field for the treatment of waste water and in sewage systems.

Part number Description Size Packing0900-SANURiL115/20 Sanuril 115 tablets 146 gram Ø 67 mm 20 kg bucket

Key features• Slow dissolving• Rapid bacteria kill• Bacteria regrowth control• Less chemical required to the job

Key features• Suitable for soft and medium

hard water• High chlorine content of 70% • Rapid bacteria elimination• Bacteria regrowth control• Applicable for all kind of sewage

applications

Key features• Neutral pH- effect on the treated

water • Suitable for soft and medium hard

water• High chlorine content of 85-90%• Rapid bacteria elimination• Bacteria regrowth control• Very effective and efficient


Key features• Bio degradable antiscalant for

reverse osmosis• Eco-friendly product• Non-hazardous product

Anti Scalant eco FriendlyHDC-ASI-ECO is an antiscalant based on biopolymers and is for use in RO membrane systems. This product is an all-organic type and based on biodegradable compounds. HDC-ASI-ECO disperses inorganic deposits to guarantee an optimal water flow.

Based on OECD-testing HDC-ASI-ECO can be classified as inherently biodegradable (20-60%).

HDC-ASI-ECO conforms to the requirements of NSF/ANSI Standard 60 - Drinking Water Treatment Chemicals - Health Effects.

Part number Description Dosage Packing0920-HDASi01B/eCO1 HDC-ASI-ECO1 Biodegradable

anti scalant1,5- 5 gram per m³

20 ltr/can (20 kg)

0920-HDASi02B/eCO2 HDC-ASI-ECO2 Biodegradable anti scalant

4 - 10 gram per m³

20 ltr/can (20 kg)

Alkaline Membrane Cleaning ChemicalsHDC-ALK-002 is a general purpose alkaline membrane cleaner and has been approved for drinking water applications by various membrane manufactures. It is effective against most organic foulants typically found in reverse osmosis systems HDC-ALK-002 is also effective against colloidal silica fouling and aluminum based foulants. HDC-ALK-002 has been approved for use in drinking water applications and for use by most membrane manufacturers.

Part number Description Dosage Packing0920-HDALK02A HDC-ALK-002 Basic alkaline

cleaner2-3% 10 ltr/can (10 kg)

0920-HDALK02B HDC-ALK-002 Basic alkaline cleaner

2-3% 25 ltr/can (25 kg)

Acid Membrane Cleaning ChemicalsHDC-ACD-001 is an inorganic scale cleaner and iron deposit remover for use in reverse osmosis and nanofiltration membranes. HDC-ACD-001 is also effective against aluminum based foulants. HDC-ACD-001 has a self-adjusting pH which ensures the most optimal solubility of iron salts and can be used with both polyamide and cellulose acetate membranes. HDC-ACD-001 has been approved for use in drinking water applications and for use by most membrane suppliers.

Part number Description Dosage Packing0920-HDACD01A HDC-ACD-001 Basic acid

membrane cleaner3-4% 10 ltr/can (10 kg)

0920-HDACD01B HDC-ACD-001 Basic acid membrane cleaner

3-4% 25 ltr/can (25 kg)

Key features• Minimise scale and fouling • Extends membrane life• Minimise performance loss

Key features• Highly effective• Non-hazardous• Extends membrane life• Minimise performance loss



HW Potable Water 445+ StabiliserThe HW Potable Water stabiliser 445+ inhibitor is developed to prevent and control corrosion in potable water systems. It is a concentrated liquid product that can be used in drinking water system to prevent corrosion and scaling.

The HW water stabiliser 445+ is a approved product to use in a drinking water system and typically dosed with a Hatenboer-Water PDU dosing unit.

Packed in a 25 litre poly can.

Part number Description Packing0950-HW445+ HW-water stabiliser 445+ corrosion inhibitor

for drinking water22 ltr/can (22 kg)

Kugaokeanos Kugoakeanos is adding various minerals, such as sodium, calcium and magnesium compounds, to distilled water to produce drinking water.

• Add this additive at the ratio of 100 g (100 ppm) per 1 ton of drinking water.• Inject a previously dissolved 2 -3 % solution into the drinking water tank.

Part number Description Packing0915-KUGAOKeA Distilled water additive 1 kg / bag

Key features• Prevent scaling • Control corrosion• Developed for drinking water

Key features• Produce drinking water

from distilled water • Well balanced minerals • Dosing quick and easy


5.4 DemineralisersWater conditioning

The Hatenboer-Water Demiflow (HDF) system delivers fully demineralised water, of the highest quality, in seconds. It is based on the ion-exchange principle. All in the water soluble hardness scalars, salts, acids and alkaline will be absorbed by the mixed bed resin. This process continues until the resin becomes saturated. At this point the resin needs to be regenerated or changed. Hatenboer-Water can supply you these resins out of stock.



Demiflow Demineralisers (HDF)The Hatenboer-Water Demiflow Demineraliser system (HDF) delivers full demineralised water, of the highest quality, in seconds. The HDF system is installed directly on the main water supply, but it can also be used as post-treatment for RO water (polishing). The basic set contains a pressure resistante (max 6 bar) replaceable demi-cartridge, resin filling, the distributor head and a connection set.

The Hatenboer-water Demiflow Demineraliser system contains a mixed bed resin that is based on the ion-exchange principle. All in the water soluble hardness scalars, salts, acids and alkaline will be absorbed by the resin, until the resin becomes saturated. At this point the resin needs to be regenerated or changed.

eC measuring The conductivity of the demi-water indicates the saturation of the mixed bed resin. This prevents the user from using hard water without noticing.

Continuous production Hatenboer-Water can offer a Duplex HDF system when a continuously production of demi-water is demanded. This system includes two filled Demiflow cartridges connected to a conductivity meter. This allows the user to replace the cartridges separately in order to avoid interruption in the production flow.

Part number Max. production*

Resin volume

Period capacity by 1 meq/ltr

Operating weight

litre/hour litre litre kg

HDF-8 175 8 1900 14

HDF-11 300 11 2600 18

HDF-25 500 25 6600 37

HDF-40 900 40 9800 56

HDF-75 1250 75 18800 101

HDF-103 1500 103 25480 140

*At 2 bar pressure drop

Key features• Water quality < 1 μS/cm• Fast production• Durable cartridge


5.5 Water SoftenersExtend the lifetime of hot water equipment on board

Water softening is the removal of calcium, magnesium, and certain other metal cations in hard water. The resulting soft water extends the lifetime of hot water machines like dish washers, laundry machines, steam ovens, steam boilers, calorifiers etc.

Hatenboer-Water has a wide range of sustainable water softening systems that are designed to be cost effective. Various types, compact cabinet for small flows in simplex or duplex.



Softeners HWS-SCA

Technical operationHatenboer-Water own water softeners series are mechanically or digitally controlled in several configurations. The regeneration control possibilities are time clock, volume, twin or duplex. The range comprises first class compact (resin and salt tank integrated), simplex (one resin tank) and duplex (two resin tanks) designs with a flow range of 50 ltr up to 78m3/hr. Operating with 230V, 50/60 Hz or on battery.

Compact seriesDue to the cabinet configuration this softener is easy to install. Resin and salt tanks are integrated in a relatively small design for water flows up to 1500 litres/h. All components are build in one plastic housing.

Resin and salt tanks are integrated in a relatively small design for small water flows up to 30 litres. All components are build in one plastic housing.

Part number Capacity Period capacity @ 1°dH

Salt per reg.

Salt tank Dimensions (cm)

m3/h m3 kg litre H x W x D

HWS-SCA 8-1 Bingo

0,5 24 0,5 25 35,5 x 28 x 48

HWS-SCA 10-1 0,6 30 0,7 100 45 x 32 x 56

HWS-SCA 20-1 1,2 60 1,4 100 113 x 32 x 56

HWS-SCA 30-1 1,8 102 2,1 100 113 x 32 x 56

Simplex seriesThe Hatenboer-Water Simplex Water Softener series have one single resin tank, the resin and salt tanks are positioned separately.

Part number Capacity Period capacity @ 1°dH

Salt per reg.

Salt tank

Dimensions (cm)

Dimensions salt tank (cm)

m3/h m3 kg ltr Height Ø Height Ø

HWS-SCA 10-1 0,6 30 0,7 100 45 20,8 68 44

HWS-SCA 20-1 1,2 60 1,4 100 88,7 20,8 68 44

HWS-SCA 30-1 1,8 102 2,1 100 88,7 25,7 68 44

HWS-SCA 40-1 2,4 136 2,8 100 112,4 25,7 68 44

HWS-SCA 60-1 3,6 204 4,2 150 123,8 30,4 80 50

HWS-SCA 75-1 4,5 255 5,3 200 138,1 33,4 105 49

Key features• Powered by 2 alkaline batteries• Digital display• Low noise flow control system• Time and volumetric based

regeneration• Proportional mixing device• ¾” connector with sample tap


6. Water MonitoringTesting equipment

To ensure a constant quality of your drinking, process or product water, Hatenboer-Water has various test kits and measuring devices available. As specialist in water treatment, we carefully composed dedicated test kits to ensure that you comply with regulations once you have a specific test kit on site or on board. MLC and NIPH are exemplary. In doubt whether your situation stands up to the authorities? Please consult our Water Quality department.


6.3 Sewage effluent Test KitsTo comply with Marpol regulationsp. 100

6.4 Boiler Water Test Kits P Alkalinity, chloride, pH

p. 104

6.1 Fresh Water Test KitsDedicated test kitsp. 92

6.2 Hadex® Test KitsChlorine monitoringp. 96

6.6 Measuring Devices Hardness, pH, conductivity, total and free chlorine or salinityp. 108

6.5 Cooling Water Test Kits Nitrate, chloride, pHp. 106


6.1 Complete Fresh Water Test KitsDedicated test kits to comply with applicable regulations

To ensure a constant quality of your potable, process or product water, Hatenboer-Water supplies fresh water test kits. The fresh water test kits combine tests for all necessary parameters in potable water to be measured. These test kits have an excellent value for money and are in addition to their completeness also easy to use. With these kits you are in full compliance with latest 2013 NIPH or MLC regulations. Contact our Sales Department when you can't find your parameter.

M L Ccompliance


6. Water Monitoring

Complete Fresh Water Test Kits For Offshore industryThe Complete Fresh Water Test Kit is a self contained test kit for almost all parameters in drinking water to be measured. The various tests included in this all-in-one kit help you to analyse all key parameters in order to comply with the guidelines.

Contents• Free and Total Chlorine Hadex® digital photometer (0 - 10 ppm and 0 - 2 ppm)• pH digital meter• Digital conductivity meter 0 - 1999 μS/cm• Total hardness test kit• Digital thermometer

SamplingAnalysis is only as good as the sample being tested. Various tests and/or analysis require samples taken from specific points in a tank or distribution system. The complete test kit is equipped with all necessary supplies needed to properly collect a water sample for testing. If in doubt or when you need extra hands, please contact our Water Quality department: [email protected] for safe water on board. More information on our Water Quality Services in the chapter 'Services'.

NIPH/MLC regulationsSeveral associations and other bodies have drawn up guidelines for the drinking water quality in the maritime and offshore industry. This means that regular water quality checks are absolutely essential. Targeted water treatment is the only way to ensure that water quality is always maintained at a satisfactory level. The various tests included in this all-in-one kit help you to comply with the guidelines.

Part number Description

0500-000012 Complete Fresh Water Offshore Test Kit


0-2 ppm100 pcs


100 pcs


100 pcs

0510-HWPH701 pH 7 Buffer solution, 500ml 1 pc

0510-HWPH101 pH 10.1 Buffer solution, 500ml 1 pc

0510-000007 Conductivity Calibration solution, 500 ml Range: 1413µS/cm

1 pc

0500-000011 Conductivity Meter (portable)

Type: SD70 Range: 0 - 1999µS/cm Resolution: 1µS/cm

1 pc

0500-000050 pH Meter (handheld)

Type: SD50 Range: 0 - 14

1 pc

0590-000008 Thermometer (folding probe) Type: Testo 104 Range: -50 - 250°C

1 pc


Key features• Compliance with NIPH/MLC• Compact hand-held meters• Easy-to-use• Accurate results• Quick start guide & manual included


Key features• Helps to comply with NIPH/MLC• Ensures safety for shipboard personnel• Compact hand-held meters• Self contained test kit• No need for calibration• No buffer solutions• Easy-to-use• Manual included

Complete Fresh Water Test Kits for Maritime UseThis basic test kit is suitable for monitoring the common parameters onboard. Monitors a sufficient number of parameters for all identified risk points. All tests are delivered in a robust and compact case including instructions. Test frequencies will differ per flag state/country. Depending on authority and flag state optional tests may be required.

Contents• Chlorine / Hadex® colourimetric test kit including 30 tablet reagents (0 - 4 ppm)• pH test strips, 100 pcs, pH 6 - 10• Conductivity digital meter 0 - 1999 uS/cm• Total hardness test kit• Digital thermometer

SamplingAnalysis is only as good as the sample being tested. Various tests and/or analysis require samples taken from specific points in a tank or distribution system. The complete maritime test kit is equipped with all necessary supplies needed to properly collect a water sample for testing. If in doubt or when you need extra hands, please contact our Water Quality department: [email protected] for safe water on board. More information on our Water Quality Services in the chapter 'Services'.

Part number Description

0500-000019 Complete Fresh Water Maritime Test Kit

Spare partsPart number Parameters Description Packing0525-DPD01RAP Free and Total Chlorine

(low range)DPD no.1 rapid tablets 100 pcs

0525-DPD03RAP Free Chlorine (high range)

DPD no.3 rapid tablets 100 pcs

0500-000015 Hardness Reagent, 15ml 1 pc

0521-000009 pH 6 - 10 Test strips 100 pcs

0510-000007 Conductivity Calibration solution, 500 ml Range: 1413µS/cm

1 pc

0500-000011 Conductivity Meter (portable)

Type: SD70 Range: 0 - 1999µS/cm Resolution: 1µS/cm

1 pc

0525-145500 Sample cells with cap 10ml 10 pcs

0525-146040 Chlorine 0 - 2 mg/l Colour disc for Hadex® Checkit comparator

1 pc


6. Water Monitoring

Hygicult incubatorsThe Hygicult is a test kit with an incubator for convenient on-site sampling and analysing. The test kit is used for rapidly monitoring the general hygiene status of fresh water. With the test kit it is possible to test the TPC (total plate count), monitor total bacterial counts and detect Enterobacteriaceae and Escherichia coli.

The set is small and light and can easily be transported to the location of use. Tests can be performed on-site, or the slides can be used as convenient transport media for samples.

The incubator has a transparent door, which allows you to check inside the incubator without opening the door. It is also equipped with a thermometer and multi-rack shelf.

SamplingLiquids can be analyzed by dipping the growth medium in the liquid for 3 - 4 seconds.

IncubationAfter sampling the agar slides must return into test tube. Close the test tube with the screw-cap. The tubes are not be frozen under any condition. The agar slides have to incubated for 1 - 2 days at a temperatures of 35 – 37°C.

Results After incubation, remove the agar slides from the test tube and interpret the growth- color reactions according to the instructions. Compare the density of the colonies in the agar surface with the example on the instruction manual.

Incubator

Part number Description Cat. No. Culture Media items per SKU

0590-000047 3M™ Dipslides w/PCA/MacConkey 3 DPSCDSC2 Side 1 Total Count using a Plate Count Agar Side 2 Coliform count using VRBA

10

0590-000031 3M™ Dipslides - TSA/Rose Bengal CAF DPSLDRBS Side 1 Total Count using Tryptose Soya Agar Side 2 Yeast and Mould count using Rose Bengal

10

0590-000027 3M™ Dipslides - PCA/MacConkey + Neut DPSLDSCN Side 1 Total Count using a Plate Count Agar Side 2 E.coli count using a MacConkey Agar

10

0590-000048 3M™ Dipslides w/PCA + TTC/MacConkey DPSLDSCT Side 1 Total Count using a Plate Count Agar with redspot indicator Side 2 Coliform count using VRBA

10

Key features• Rapid monitoring of micro-biological

hygiene • Easily transported because of the

small size • Reliable and durable • Modern and efficient way of microbial

sampling• Test results easily interpreted • Samples don’t need to be sent to a

laboratory on-shore• Interpret results with model chart

included in the set

Part number 0500-CULTURA

Temperature range 25 - 45°C

Temperature ± 1°C

Voltage / Frequency 230 Volt (110 V) / 50 - 60 Hz

Consumption 26 W / 0,2 A

Safety class II

insulation Double SEV-tested

Thermometer up to 60oC, in special container

Base / construction ABS white

external dimensions (W x H x D) 310 x 155 x 168 mm

Weight 1,1 kg


6.2 Hadex® Test KitsDedicated test kits for chlorine monitoring

As a food grade disinfectant Hadex® is especially intended for disinfecting drinking water in tanks and pipelines. The amount of free chlorine gives an

indication of the available amount of Hadex® in your

potable water. The range Hadex® test kits consists of electronic and manual testing devices. More details

on Hadex® can be found in chapter 2 on Water Disinfection.


6. Water Monitoring

Hadex® Digital Test KitsThe Hadex® Digital Test Kit is a compact, portable instrument to test key water quality parameters. Due to microprocessor technologies the chlorine level in your potable water is measured in the most effective and precise way. The testing results can be read immediately and gives you the opportunity to adjust (if necessary) your dosing programme at once.

Offshore proofThis test kit is the best way to analyse free chlorine in the drinking water disinfectant Hadex®. The photometer has been designed with particular attention to the environmental conditions encountered in maritime use. The keyboard and display are splash proof. The sample chamber, the most critical part of any photometer is fully sealed, so no water can penetrate into the electronic components. Cleaning is simple. The cuvette cover is used to eliminate the effects of ambient light. With the High Range reagents this test kit meets the conditions of the NIPH.

Contents• Instruments in carrying case• Batteries included• Round glass vials with lids• Powder reagents sufficient for 100 tests• Guarantee sheet• Certificate COC• Step-by-step instruction manual

Characteristics• Free & Total Chlorine - DPD no.1 and no.3• Range: 0 - 2 ppm• High range: 0 - 10 ppm

Part number Description0500-000008 Free Chlorine / Hadex® Digital Test Kit


0-2 ppm100 pcs


100 pcs


100 pcs


All you need in one case! Of course a manual has been included.

Key features• Large backlit digital display• SMD-microprocessor technology• LED with long term light stability• Operating mode selection• Uses long-life reagent tablets• Carrying case


Hadex® Manual Test Kits: Checkit ComparatorThe Hadex® Checkit is a compact, colourimetric kit which is suitable to manually measure the amount of available Hadex® in your potable water. Hadex® is a food grade drinking water disinfectant. Supplied with a generous number of different colour scales, the kit provides the basis for a comprehensive, easy-to-use colourimetric analysis system.

Characteristics• Contains 30 tests• Unrestricted shipment• Testing range of 0 - 2 mg/ltr

Part number Description0500-HADeXTeSTKiT Hadex® Manual Test Kit

Spare parts Part number Spare parts0525-000028 DPD no.1 Free Chlorine high range tablets 0-10 ppm NIPH

0525-000029 DPD no.3 Total Chlorine high range tablets 0-10 ppm NIPH

145500 Sample Cells 10 ml with cap (10 pc)

146040 Colour disc for Hadex® Checkit comparator

Hadex® Test StripsThe Hadex® Test Strips are indicative and easy to use. Just dip a strip into water, move it back and forth 30 seconds and read by comparing the pads to the colour chart on the container. Technicians in the field can test many samples in only a few minutes and make immediate evaluations on-site.

Characteristics• Testing range 0 - 10mg/l• Free and Total Chlorine• Contains 50 tests

Part number Description0505-27450-50 Hadex® Test Strips (Free and Total Chlorine)

Key features• High accuracy• Tablet reagents with a minimum

guaranteed shelf life of 5/10 years• Easy operation and exact reagent

dosing

Key features• Accurate quick indication• Indicative and easy to use• No measuring, set-up, clean-up, or

chemical handling are necessary• Great for quick, on-site evaluations of

free and total chlorine levels


6. Water Monitoring

In doubt whether your situation stands

up to the authorities? Please consult

our Water Quality department. More

information in the chapter 'Services'.


6.3 Complete Sewage effluent Test KitsTo comply with Marpol regulations

The discharge of raw sewage effluent into the sea can create a health hazard, while in coastal areas sewage can also lead to oxygen depletion and obvious visual pollution. Environment protection is very important nowadays. Besides taking care of clean water for your crew, we feel responsible to care for the environment. To help you to comply with Marpol regulations we can supply you with the appropriate test equipment.


6. Water Monitoring

Digital Maritime Sewage effluent Test Kits It is important that the condition of sewage effluent discharges is checked to ensure they comply with the regulations. The Digital Hatenboer Sewage Effluent Test Kit is very user friendly and measures the parameters of the onboard treatment systems according to the Marpol regulations (adopted in resolution MEPC.115(51) concerning the effluent discharge. Regular testing will allow rapid corrective action to take place if required, helping to maintain optimum operating conditions, minimum down time and reducing costs.

CharacteristicsDue to the presence of all necessary test devices a day to day quality control of the sewage effluent treatment plants on board are guaranteed.

Contents• Physical

• pH • Chlorine• Total Suspended Solids (TSS)

• Biologial • E-coli and Coliforms• BOD (Biological Oxygen Demand)• COD (Chemical Oxygen Demand)

Part number Description Parameters SizeL x W x H (cm)

0500-000026 Digital Sewage Effluent Kit

pH,Cl, TSS, E-Coli, coliforms, BOD and COD

78 x 38 x 38

Spare partsPart number Parameters Description Packing0525-000049 Free and Total Chlorine Buffer solution (high

and low range) 65 ml1 pc

0525-000048 Free Chlorine (low range) Titrant, 65 ml 1 pc

0525-000005 pH tablets Range 4.0 - 10.0 100 pcs

0525-DPD01RAP/100 Free and Total Chlorine (low range)


0525-DPD03RAP/100 Free Chlorine (high range) DPD no.3 rapid tablets 100 pcs

0525-000047 Permanganate value Tablets 200 pcs

0525-000046 Permanganate value Acidifying SE tablets 100 pcs

Key features• Complete equipment for testing

effluent discharge• Supplied in two robust casings• Biological tests with incubator• In compliance with Marpol Annex IV


Standard Maritime Sewage effluent Test Kits The Standard Hatenboer-Water Sewage Effluent Test Kit provides a simple means of monitoring the quality of sewage effluents. Regular testing will allow rapid corrective action to take place if required.

CharacteristicsEach of the tests can be performed without the use of complicated equipment. The kit helps to maintain optimum operating conditions, minimum downtime and reducing costs.

ContentsThe kit will be delivered in a robust case together with applicable reagents, buffer solutions, measuring devices etc. An instruction manual and log sheet are also provided.

Description Range PackingpH 4.0 - 10.0 100 tablets

Free Chlorine (High range) 0 - 300 mg/l 9PPMO 100 tablets DPS 3

Free + Total (Low range) 0 - 1 mg/l

Permanganate value

TSS (Turbidity and Suspended Solids) Comporator


0500-000027 Standard Sewage Effluent Kit

Permanganate, pH, chlorine, TSS, BOD/COD/TOC, temperature

53,5 x 36 x 13

Spare partsPart number Parameter Description Packing0525-000005 pH tablets Range 4.0 - 10.0 100 pcs

0525-DPD01RAP Free and Total Chlorine (low range)


0525-DPD03RAP Free Chlorine (high range) DPD no.3 rapid tablets 100 pcs

0525-000049 Free and Total Chlorine Buffer solution 65 ml (high and low range)

1 pc

0525-000047 Permanganate value Tablets 200 pcs

0525-000046 Permanganate value Acidifying SE Tablets 100 pcs

0525-000037 Colour disc Chlorine Range 0 - 1 mg/l 1 pcs

0525-000058 Colour disc pH Range 4.0 - 10.0 1 pcs


effluent discharge• Accurate testing• Supplied in a robust case• Biological tests with incubator• In compliance with Marpol Annex IV


6. Water Monitoring

Basic Sewage Water TestersThe Basic Test Kit provides simple testing for the most popular sewage treatment agents. Measuring two parameters simultaneously, the test kit uses rapid dissolving tablets to give accurate reliable results quickly.

ContentsEach test kit is supplied in a robust case with tablet reagents for 20 tests, and an instruction manual.

Part number Description Chlorine range Parametersmg/l pH

0590-AF106 Basic Sewage Tester 0,5 - 6 6,8 - 8,2

Spare partsPart number Description Packing0525-DPD01RAP DPD no.1 Free and Total Chlorine low range rapid

tablets100 pcs

0525-DPD03RAP DPD no.3 Free Chlorine low range rapid tablets 100 pcs

0525-PHeNOLROOD Phenol red tablets 100 pcs

Key features• Easy to use• Quick results• Simple testing


6.4 Boiler Water Test KitsP Alkalinity, chloride, pH

Water treatment of boiler systems is an integral operation for many industries, with productivity and product quality hanging in the balance.

Scale, corrosion, fouling, microbiological contamination and other water treatment problems can be costly. Monitoring the quality of boiler water helps you to achieve water and energy efficiency, asset preservation, and enhanced reliability and safety.


6. Water Monitoring

Boiler Water Test Kits Measuring and monitoring treatment levels in boilers is essential to maintaining output efficiency. Failing to maintain the proper water quality can result in serious problems such as accumulation of scale (reduced heat transfer, blocking pipes), corrosion (leaks) and reduced steam purity. Not to mention increased biological activity. The test equipment in this Boiler Water Test Kit enables personnel to ensure treatments such as corrosion and scale inhibitors are correctly dosed.

CharacteristicsThe Boiler Water Test Kit contains all equipment and test reagents for everyday boiler water testing, optimising treatments and monitoring critical control parameters. The test kit is based on tablet count method and colour comparator chemistry. Instructions for testing are included and the Boiler Water Test Kit is presented in its own robust case.

ContentsParameters Description Range PackingP Alkalinity Tablets 20 - 500 mg/l CaCO3 250 pcs

Chloride Tablets * 250 pcs

pH Test Strips 6.0 - 10.0 100 pcs

pH Colour Indicator Card 6.0 - 10.0 1 pc

Sample Tube 100 ml

Sample Tube 30 ml

Stirring Rod

Sample Lock 20 ml

* Range Sample Size mg/l Cl (mg/l NaCl) Sample Size 0 – 100 0 – 160 100 ml 0 – 200 0 – 320 50 ml 0 – 1000 0 – 1600 10 ml 0 – 5000 0 – 8000 2 ml


0500-000061 Boiler Water Test Kit Alkalinity P, Chloride, pH 27,5 x 8 x 23

Spare partsPart number Parameter Description Packing0525-000054 P Alkalinity Tablets 250 pcs

0525-000055 Chloride Tablets 250 pcs

0525-000046 pH Test Strips 7.0 - 14.0 100 pcs


boiler water• Accurate dosage of corrosion and

scale inhibitors• For daily analysis• Rugged, compact, portable design


6.5 Cooling Water Test KitsNitrate, chloride, pH

Water treatment of cooling systems is an integral operation for many industries, with productivity and product quality hanging in the balance.

Scale, corrosion, fouling, microbiological contamination and other water treatment problems can be costly. Monitoring the quality of cooling water helps you to achieve water and energy efficiency, asset preservation, and enhanced reliability and safety.


6. Water Monitoring

Cooling Water Test Kits Measuring and monitoring treatment levels in cooling water systems and closed water systems is essential to maintaining output efficiency. Failing to maintain the proper water quality can result in serious problems such as accumulation of scale (blocking pipes), corrosion (leaks) and increased biological activity that can result in the growth of Legionella bacteria. The test equipment in this Cooling Water Test Kit enables personnel to ensure treatments such as corrosion and scale inhibitors are correctly dosed.

CharacteristicsThe Cooling Water Test Kit contains all equipment and test reagents for everyday cooling water testing, optimising treatments and monitoring critical control parameters. The test kit is based on tablet count method and colour comparator chemistry. Instructions for testing are included and the Cooling Water Test Kit is presented in its own robust case.

ContentsParameters Description Range PackingNitrate Tablets no. 2 70 - 1500 mg 250 pcs

Nitrate Sample conditioning tablets no. 1

- 100 pcs

Chloride Tablets * 250 pcs

pH Test Strips 7.0 - 14.0 100 pcs

pH Colour Indicator Card 7.0 - 14.0 1 pc

Sample Tube 100 ml

Sample Tube 30 ml

Stirring Rod

Sample Lock 20 ml

* Range Sample Size mg/l Cl (mg/l NaCl) Sample Size 0 – 100 0 – 160 100 ml 0 – 200 0 – 320 50 ml 0 – 1000 0 – 1600 10 ml 0 – 5000 0 – 8000 2 ml


0500-000060 Cooling Water Test Kit Nitrate, Chloride, pH 27,5 x 8 x 23

Spare partsPart number Parameter Description Packing0525-000057 Nitrate no. 1 Sample conditioning tablets no. 1 100 pcs

0525-000056 Nitrate no. 2 Tablets 250 pcs

0525-000055 Chloride Tablets 250 pcs

0525-000014 pH Test Strips 7.0 - 14.0 100 pcs


cooling water• Accurate dosage of corrosion and

scale inhibitors• For daily analysis• Rugged, compact, portable design


6.6 Single Parameter Measuring Devices pH, conductivity, total and free chlorine or salinity

Hatenboer-Water selected products are designed to provide simplicity of testing high accuracy and to survive marine conditions; both aspects making them ideal for use in marine and offshore industry. You can think of devices for the measurement of hardness, pH, conductivity, total and free chlorine or salinity. All test instruments are attuned to their specific task.


6. Water Monitoring

pH MetersThe Hatenboer-Water pH meter is a compact, easy to use handheld meter for the measurement of pH.

Up to 25 results can be stored in the meter's memory with date, time and temperature information for each result. A backlit LCD display shows result and temperature simultaneously, with additional information including date and time on key press making accurate measurements simple.

The robust housing is completely waterproof (IP67) and the scroll bar functionality combined with a backlit display results in an easy read out.

RangepH 0 - 14

Temperature 0 - 60°C

Resolution pH 0.01 Temp 0,1 °C

Calibration 3 point

Data storage 25 data sets with date, time, temperature results

Display LCD, 22 x 22 mm: backlit

Conformity CE

Part number Description Range PackingpH pH cm

0500-000030 pH meter (handheld), type SD 50 + calibration solution

0.0 - 14.0 17,5 x 4,1 x 2,3

Conductivity TestersThe Hatenboer-Water Conductivity Tester is an ideal tester for measuring your conductivity in a quick view. The compact design enables you to measure the conductivity – (temperature compensated) easily.

With a storage of 25 data sets, each with date and time stamp this tester also gives you an easy recall of data record keeping requirements. The electrode is replaceable to continue a long-life functionality.

The housing is completely waterproof (IP67) and together with the scroll-bar functionality and LCD display with backlit results in an easy readout.

Range

eC 0 - 1999 μS/cm


Resolution 1 μS/cmTemp 0,1 °C

Calibration 2 point

Data storage 25 data sets with date, time, temperature results

Display LCD, 22 x 22 mm: backlit

Conformity CE

Part number Description Range Packing μS/cm cm

0500-000011 Conductivity meter, (handheld) type SD 70 + calibration solution

0 - 1999 17,5 x 4,1 x 2,3

Key features• Backlit display• Replaceable electrode • Compact handheld meter• Waterproof tester (IP 67)• Storage function (25 sets)

Key features• Backlit display• Low battery indicator• Compact handheld meter• Accurate measurements• Storage function (25 sets)


Conductivity TestersPure Water Test (PWT) enables you to check the purity of your distilled water in laboratory or industrial environments.

The casing features a larger LCD and an ergonomic shape. This tester is supplied with a protective cap, calibration screwdriver batteries and instructions. A durable case provides excellent protection against maritime environments.

Range

eC 0 to 99.9 μS/cm


Resolution 0,1 µs/cm Temp 0,1 °C

Calibration manual, 1 point

Display LCD

Conformity CE

Part number Description Range DimensionsμS cm

0510-Hi98308 Conductivity Tester Pure Water 0 - 99.9 17,5 x 4,1 x 2,3

Testo 104 ThermometersIt is important to measure the temperature of the water frequently to carry out your legionella control measures accurately. Temperatures between 25 and 45 degrees stimulate the growth of the legionella bacteria.

The Testo 104 measures the temperature quickly and accurately. After the measurement you can easily snap shot the sensor and store the data until the next measurement. The thermometer is compliant with HACCP guidelines and the standard EN 13485 to prevent legionella, keep your hot water hot and your cold water cold.

Part number Description Range Dimensionsmin max cm

0590-000008 Portable thermometer Testo 104 -50°C 250°C 26,5 x 4,8 x 1,9

Key features• Long battery life• Replaceable probes• Single point calibration• Measuring your pure water

(demi-water) quality

Key features• Waterproof (class IP65)• Accurate measuring• Automatic memory of final value


6. Water Monitoring

Turbidity MetersTurbidity can indicate a gross contamination with biological material, corrosion or dirt entering the system during delivery. According to the WHO the turbidity of potable water should be < 1 NTU.

The infrared turbidity meter is designed to allow fast, precise on-site testing. The wide measuring range makes the instrument suitable for various applications, ranging from drinking water, sea water intake to waste water.

As infrared light is used for measurement purposes, the unit is suitable to test coloured and colourless liquids. The standards required for calibration of the unit are also supplied.

Part number Description Range DimensionsNTU cm

0500-PCCheckF Turbidity tester 0.01 - 1100 19 x 11 x 5,5

Key features• Range 0,01-1100 NTU• Auto ranging• 600 tests without battery change• Display backlit LCD• Memory for 16 data sets• Instrument in carrying case


7. Water HeatingHot water supply

The Hatenboer-Water Maritime Fresh Water programme includes a wide range of hot water calorifiers. These high quality calorifiers are specially designed for maritime use and provides a sea going vessel or offshore rig with a very reliable hot water supply.


7.1 Water HeatingHot water calorifiersp.114


7.1 Water HeatingHot water supply

The Hatenboer-Water Maritime Fresh Water programme includes a wide range of hot water calorifiers. These high quality calorifiers are specially designed for maritime use and provides a vessel or offshore rig with a very reliable hot water supply. The sturdy configuration of all elements is offshore proof and guarantees a long lifespan. If requested we can supply you with a plug and play skid.


7. Water Heating

Hot Water CalorifiersThe calorifiers are manufactured standard as models with a stainless steel (type R) inner tank or copper lined (type S) inner tank. The stainless steel version is available in volumes from 30 to 1000 litres and the copper lined types are available in volumes from 1000 to 3000 litres. If required horizontal models are available. The calorifiers are delivered including insulation (Rockwool) Outside covering is made of epoxy coated steel plates (standard colour is blue).

HeatingAs heating sources can be used as main heating or as back-up heating applied: electricity, steam, hot water or thermal oil, whatever is available. The electrical heating can be combined with the other heating sources. As a back-up the electric heating is used if the other heating source is not sufficient or available, e.g. in dock.

CertificationThe calorifiers can be delivered with several classification certificates, including GL, DNV, LR and ABS.

InstallationThe calorifiers are delivered as time saving, ready for start-up units, complete with required accessories and insulation. Electrically heated models are supplied complete with heating and safety thermostats.

Options• Built on electrical connection box for electrical heating• Hot water circulation pumps for tap water

Key features • High quality • Ship execution • Custom building possible • Delivered complete, ready for use

Model Heating Power supply Volume Diameter Height Weightsystem litre cm cm kg

15R-30 E* 230V-50/60Hz 30 43 46 10

15R-50 E* 230V-50/60Hz 50 43 68 15

15R-80 E* 230V-50/60Hz 80 43 100 45

15R-100 E* 230V-50/60Hz 100 43 122 50

15R-150 E* 230V-50/60Hz 150 43 169 60

17R-80 E\HW\D* 380-690V 50/60Hz 80 58 55 70

17R-120 E\HW\D* 380-690V 50/60Hz 120 58 72 75

17R-200 E\HW\D* 380-690V 50/60Hz 200 58 115 90

17R-300 E\HW\D* 380-690V 50/60Hz 300 58 160 110

17R-400 E\HW\D* 380-690V 50/60Hz 400 58 215 140

17R-600 E\HW\D* 380-690V 50/60Hz 600 78 195 180

17R-1000 E\HW\D* 380-690V 50/60Hz 1000 100 210 300

17S-1000 E\HW\D* 380-690V 50/60Hz 1000 100 210 400

17S-1500 E\HW\D* 380-690V 50/60Hz 1500 120 211 580

17S-2000 E\HW\D* 380-690V 50/60Hz 2000 130 215 800

17S-3000 E\HW\D* 380-690V 50/60Hz 3000 150 226 820 *E = Electric, HW = Hot Water, D = Steam


8. Water ConsumptionSafe water at every tap point

Safe water can be continuously available with the use of our selected water coolers and drinking water filters. Hatenboer-Water has a range of products to make sure that your water is healthy and tasty. Our point of use water coolers are connected directly to the water mains alleviating handling, logistics and waste issues. Various in-line filters help to improve taste and odour, next to removing sediments.


8.1 Water Coolers and Single Tap Point ConditioningPOu dispensers

p.118

8.2 Pentair® everpureQuality improvement by POu filtration

p.122


8.1 Water Coolers and Single Tap Point ConditioningPOU dispensers for optimising quality

MLC 2006 states that (cooled) water must be freely

accessible to everyone on board, Hatenboer-Water

offers water coolers and filtration solutions that

provide fresh water on the spot. All coolers can be

connected directly to the water mains. Applying

filtration will result in a better water taste and will also

provide protection against contaminants.



Drinking Water Cooler RiverThe River drinking water cooler for direct and continuously chilled water is constructed of hygienic stainless steel (AISI316) material. The robust design makes the it highly suitable for operating in a maritime environment. The River is connected to the main waterline and the water is chilled directly making replacement of water bottles redundant, which results in considerable cost saving and reduction of logistics.

CharacteristicsThe River is available as a floor standing model, a wall mounted model (River UP) is optionally available. Both models can be supllied in heavy duty materials: galvanized steel plates covered stainless steel outer shell. The water coolers are equipped with two practical taps, a glass filler tap and a drinking fountain.

OptionsOn locations where the drinking water quality is discussable, the drinking water cooler can optionally be equipped with the stainless steel HIS filter house and Supercarb filter element for superior drink water quality. This filter removes deposits, improves smell and taste and prevents bacterial growth.

MLCAccording the MLC a water cooler in the galley is mandatory to provide cooled and safe water to the crew.

Part number Description Capacity Power Dimensionslitre/h W x D x H (cm)

1200-RiVeR30 River 30 Floor standing

30 180 W, 230 V 50-60Hz

34 x 32,5 x 96

1200-RiVeR55 River 55 Floor standing

55 180 W, 230 V 50-60Hz

34 x 32,5 x 96

1200-RiVeR30UP River 30 UP Wall mounted

30 180 W, 230 V 50-60Hz

43,2 x 36 x 50,5

1200-RiVeR55UP River 55 UP Wall mounted

55 180 W, 230 V 50-60Hz

43,2 x 36 x 50,5

Drinking Water Cooler AqualityThe Aquality drinking water cooler is the newest generation coolers with an elegant design. It supplies direct continuously chilled water. This model is executed with a black plastic cap, internal cup reservoirs and skin-plate outer casing.

OptionsOn locations where the drinking water quality is discussable, the drinking water cooler can be optional equipped with the Stainless Steel HIS filter house and Supercarb filter element for superior drink water quality. This filter removes deposits, improves smell and taste and prevents bacterial growth.

MLCAccording the MLC a water cooler in the galley is mandatory to provide cooled and safe water to the crew.

Part number Description Capacity Power Dimensionslitre/h W x D x H (cm)

1200-AQUALiTYAB Aquality Floor standing 28 190 W, 230 V 50-60Hz

34 x 32,5 x 96

Key features• Continuous directly cooled water

supply • Standard equipped with two

practical taps• Floor or wall mounted model available• Heavy duty maritime model• Connections 230 V / 50-60Hz• Capacity up to 50 ltr per hour

(250 glasses per hour)• Limiting bacterial proliferation and

guaranteeing high hygiene standards• Simple and quickly connected to the

drinking water distribution system

Key features• Internal cup reservoir• Continuous supply of directly chilled

water• Elegant refined floor model design• Offshore suitable model• Connections 230V / 50-60Hz• Capacity up to 28 ltrs per hour• Limiting bacterial proliferation and

guaranteeing high hygiene standards


Key features• Legionella proof, prevent further risk• Quickly create safe tap points• Capacity of 5000 liters water filtration • Water and energy saving

Rated service life 5000 litres *

Membrane class

Sterilisation Grade (> LOG 6 reduction)

Max. operating pressure

6 Bar

Max. temp 60 OC, (Max short temp < 30min) 70 OC

Product category CE-Medical, Class 1

Biological reten-tion

Log 107 / cm2, Tested at HYG

*) Depends on water quality, biological load etc. < 2

HiS Filter HouseThe HIS in-line drinking water filter has been designed to minimise space requirements, and is therefore especially suitable for use under sink or to protect ice makers and water coolers. The Hatenboer-Water selected HIS filter is considered to be very durable due to the stainless steel design.

3-staged filtrationThe filter consists of three different layers with their own capabilities, as the water flows through the filter it will pass the following layers:

Layer 1 A ceramic outer shell for micro filtration

Layer 2 Anti-bacterial formula removes Pathogenic bacteria

Layer 3 Activated carbon for taste and odour removal and chlorine removal

Part number Description Length Capacity Max.

pressureConnection

inch litre/h bar

0220-HiS HIS Drinking water filter housing, SS

10" - 8,6 1/2" BSP

0220-SUPCA10A Supercarb 10" 222 - -

T-Safe® Legionella FilterDuring water bunkering you have been assured that the supllied water is clean. You follow all the necessary water treatment procedures. You work through the Water Management Plan. But despite all the precautions there is a chance that an (Legionella) infection is detected. With the T-Safe® you can quickly and easily create a safe tap point.

The T-Safe® UF showers are designed to provide maximum safety without reduction of comfort. The included T-Safe filter, based on hollow fiber technology with a 0.15 μm membrane filter, is specifically designed to filter tap and shower water to protect your crew against infection from pathogenic bacteria.

The fast filter connection and safe to the last drop this filter retain Legionella log 107 per cm2, which meets the pharmaceutical sterility requirements. The filter can be used up to 3 months from initial use, which ensures an economical solution. All materials used in the T-Safe® products are approved by WRAS (Water Regulations Advisory Scheme) and all the products in the T-Safe® range are CE marked.

Part Number Description Connections Flow rate Colour Packing

litre/min L x B x H mm

0290-SHOWeRLeG UF Shower Filter ½” 8 - 10 Chrome 265 x 92 x 75

0200-GALLeYLeG UF Galley Shower ½” 8 - 10 Black / Chrome

265 x 92 x 75

Key features• Suitable for water coolers and point

of use• Polished stainless steel in-line filter

housing• Improves taste and odor• Chlorine, rust and sediment removal• Multistage filtration in one filter

cartridge• Removes particles (nominal) down

to 0.9 microns• Removes pathogenic bacteria




8.2 Pentair® everpureQuality improvement by POU filtration

Whether you need filtration, softening or reverse

osmosis at the entry of the tap point, Everpure

provides the most consistent water anywhere on

board of your ship, vessel or rig.

Quality water is not only important for the taste,

appearance and odour of drinking water. Correct

filtered water is equally important for the protection

of equipment such as: brewing, baking, steaming,

beverage, fountain, ice and dishwashing -equipment.

Feed water used in such equipment must be potable

and meet the (inter-)national regulations regarding

the Potable Water Quality.

Hatenboer-Water is the official dealer of the Everpure Sales programme.

O F F I C I A L

DEALEROFFICIALDEALER



Precoat FiltersThe Precoat ‘C’ filter cartridges exclusive design improves the taste and odour of drinking water due to the submicron filtration of 0,5 micron and integrated activated carbon powder.

Most filters in this range are equipped with MicroPure II AgIon media which effectively inhibits the growth of bacteria within the filter due to the bacteriostatic ability.

ApplicationThe cartridges deliver premium quality water for cold water applications such as water coolers and overall tap points.

Part number Description Capacity Height Filtration Carboncm μm

eV960112 AC Cartridge 2,840 ltr @ 1.9 ltr/min

26 0.5 Micropure I

eV960100 4C Cartridge 11,355 ltr @ 1.9 ltr/min

37 0.5 Micropure I

eV959106 2DC Cartridge 2,840 ltr @ 1.9 ltr/min

26 0.2 Micropure II

eV960146 4DC Cartridge 5,600 ltr @ 1.9 ltr/min

37 0.2 Micropure II

eV961255 MC² Cartridge 34,000 ltr @ 6.3 ltr/min

53 0.2 Micropure II

Fibredyne Carbon Block FiltersThe FC Cartridge offers an increased depth filtration due to its unique Fiberyne II media. It is a balanced cartridge for optimum performance in varying water qualities.

Application This cartridge improves the taste of fountain beverages and helps retain the drink's carbonation. It also protects drink system seals, pump, tubing and small orifices from clogging, corrosion and abrasive wear.

Part number Description Capacity Height Filtration* Carboncm μm

eV969156 2FC Cartridge 22,712 ltr @ 5.6 ltr/min

26 0.2 Fibredyne II


37 0.2 Fibredyne II


53 0.2 Fibredyne II

*Testing with the small bacterium Pseudonomas diminuta was performed by Vitens laboratory, the Netherlands, an ISO 17025 accredited lab. The tests were performed under test conditions specified in the ASTM F838-05 protocol for the validation of 0.2 μm sterilizing grade filters.

Key features• Chlorine taste and odour reduction• Particulate reduction (0.5 μm)• AgION technology (bacteriostatic)• EPA, FDA and NSF certified • Fits all Everpure filter heads• Easy change-out

Key features• Particulate reduction 0.2 μm• Bacteriostatic• NSF/ANSI Certified• Off-taste and odour reduction


Microguard FiltersThis Multi-stage filter combines membrane and carbon block technology for superior filtration results and provides a reduction of 99.9999% of bacteria and viruses by mechanical means.

Application The Microguard first reduces chlorine and corrects colour, taste and odour with a 5 micron carbon block. An integrated post filter of ‘hollow fibres’ creates a 0.15 micron barrier against the smallest particles and most bacteria.

Due to this microfiltration the Microguard is able to reduce wear and abrasion on coolers and other water-using equipment


eV963701 Microguard Pro 2 8,330 ltr @ 1.9 ltr/min

26 0.15 5 μm Fibredyne

eV963702 Microguard Pro 4 13,600 ltr @ 1.9 ltr/min

37 0.15 5 μm Fibredyne

Scale Control Combination FiltersRecognisable by the “H” or “S” stated in the product description. These combination filters has their own abilities as stated before but also contains an integrated sequestering control unit which isolates the particles which causes scaling.

Application Scaling within the system will be reduced while life time of equipment will be considerably extended.


eV961100 4H Cartridge 5,600 ltr @ 1.9 ltr/min

37 0.5 Micropure I

eV961807 OCS² Cartridge 5,600 ltr @ 1.9 ltr/min

26 0.2 Micropure II

eV961251 BH² Cartridge 11,300 ltr @ 1.9 ltr/min

37 0.2 Micropure II

eV961326 MH² Cartridge 34,000 ltr @ 6.3 ltr / min

53 0.2 Micropure II

eV961722 4CB5-S Cartridge 11,000 ltr @ 3.8 ltr / min

26 5 Carbon block


37 5 Carbon block


53 5 Carbon block

eV969176 2FC-S Cartridge 22,712 ltr @ 5.6 ltr / min

26 0.2* Fibredyne II





*Testing with the small bacterium Pseudonomas diminuta was performed by Vitens laboratory, the Netherlands, an ISO 17025 accredited lab. The tests were performed under test conditions specified in the ASTM F838-05 protocol for the validation of 0.2 μm sterilising grade filters.

Key features• Bacteria reduction 0.15 μm• NSF/ANSI Certified• Chlorine taste and odour reduction

Key features• Scale control• Chlorine taste and odour reduction• Bacteriostatic• Improves lifetime equipment• Less maintenance time and costs



QL3B Single Maritime Filter HeadCommercial quality filter head is designed exclusively to fit Everpure brand replacement cartridges. Solid and durable construction is ideal for maritime use.

Mounting bracket and screws included.

Part number Description Connection size Height Width Depthcm

eV431212 QL3B Single Maritime Filter head

3/8” BSP 9.2 9.5 2.7

everpure Claris FiltersAdjustable, ion-selective filter allows you to tailor carbonate hardness levels to match your desired water recipe.

Duoblend™ technology allows for the precise adjustment of carbonate hardness.

Features a unique 5-stage filtration process:

1. Pre-filtration removes coarse particles2. Carbonate hardness decrease through an ion exchange process3. Fine filtration4. Highly efficient carbon block removes harmful contaminants and unpleasant

tastes and odours 5. Solid membrane filter removes particles down to 5 µm for the highest levels of

equipment protection

Application Commonly used for combi-steamers, coffee machines and other steam generating applications. In addition to coffee/tea/espresso brewing, the Claris XL System is also an excellent scale prevention option for steam applications such as low volume, boilerless steam ovens.

Part number Description Capacity Height Width Weightcm kg

eV4339-10 Claris Replacement Cartridge S

1,700 ltr @ 10 °KH

31.5 9.5 1.3

eV4339-11 Claris Replacement Cartridge M

3,000 ltr @ 10 °KH

42.5 9.5 1.8

eV4339-12 Claris Replacement Cartridge L

5,600 ltr @ 10 °KH

36 13.6 3.2

eV4339-13 Claris Replacement Cartridge XL

8,000 ltr @ 10 °KH

47.5 13.6 4.3

eV4339-14 Claris Replacement Cartridge XXL

13,200 ltr @ 10 °KH

47.5 17.5 6.5

Key features• Ion Exchange• Water conditioning/softening• Scale control• Carbonate hardness adjustment

Key features• Built-in water shutoff valve• Corrosion resistant hardware• All wetted parts have passed NSF®

extraction tests


everpure Claris Ultra FiltersThe Claris ultra offers balanced alkalinity and mineral composition and features the ‘unique 5 stage’ Claris filtration.

Claris Ultra offers higher capacities versus traditional Claris due to its added sequestering agent which allows more blended water to go through the DUOBLEND bypass, putting less stress on the resin thus slowing its exhaustion.

Application The Ultra line adds an additional process that combines partial hydrogen softening and sequestering which stabilises mineral content using sequestering anions making it ideal for steam ovens with integrated boiler. The result is a balanced alkalinity and mineral composition in water, with stable and close-to-neutral pH which helps prevent lime scale formation.

Part number Description Capacity Height Width Weightcm kg

eV4339-85 Claris ULTRA Cartridge 1700 1,700 ltr @ 10 °KH

24,5 9,5 0.9


31,5 9,5 1.3


42,5 9,5 1,8


36 13,6 3,2


47,5 13,6 4,3


47,5 17,5 6,5

Claris Filter HeadsCommercial quality filter head is designed exclusively to fit Claris filter cartridges. The system can be operated freestanding, lying horizontally or mounted vertically.

We recommend combining the filter head with the Claris connection hoses and digital water meter for quick installation and in-time replacement of the cartridges.

Part number Description Connection size Height Width Depthcm

eV433990 Filter head Claris, generation 2.0

3/8” BSP 5,8 8,4 11,9

eV4339-30 Claris digital flow meter

3/8” BSP 8 4,5 4,2

eV4339-51 Connection hose 3/4” BSP 147,5

Key features• Built-in flush port• Auto shut-off when cartridge is

replaced• Adjustable bypass• Built-in backflow restrictor

Key features• Ion Exchange• Water conditioning/softening• Scale control• Carbonate hardness adjustment



Hatenboer-Water is the official

dealer of Everpure Sales

Programme. The products

presented in this catalogue are

a small selection of the complete

sales programme of Everpure.

Please contact your Sales

Representative for more

information.

MRS-600He POU Reverse OsmosisReduces lime scale build-up that can cause excessive machine downtime and increased maintenance costs. The system removes chlorine, taste, odour and other contaminants which affect the taste of water and beverages.

Application The MRS600HE Reverse Osmosis system is an ‘all-in-one solution’ designed to serve multiple foodservice applications by delivering both reverse osmosis and blended filtered water.

This tailored blending process removes just the right amount of dissolved solids from the incoming tap water to achieve the desired final water quality.

With the average recovery of 78%, the MRS-600HE system only disposes waste water with a rate of 1 out of 4. Its high recovery technology results in significant savings in water with a minimal environmental footprint.

Part number Description Capacity Height Width Depth Weightcm kg

eV997047 MRS-600 HE Reverse Osmosis system

2 ltr/min 81,2 58,4 34,5 38,6

Key features• Complete galley solution• RO & Blended product water• 78% recovery• High output• Automatic back flush without

chemicals• Integrated storage tank• Compact & easy to install

Serving multiple applications with one single investment.

O F F I C I A L

DEALEROFFICIALDEALER


ServicesWorldwide assistance

Cost reductionAt Hatenboer-Water the services a client ultimately employs

are those defined appropriate and necessary by the client’s

specific needs. Our main aim is to help you reduce your

Total Cost of Ownership.

HSE ConsultancyOur Water Quality department acts as a consultancy department

as safe water on board starts not only with proven water treatment

equipment and constant monitoring. The consultants provide

solutions so you can comply with international laws and assure that

your crew is working in safe conditions.

ServicesWorldwide assistance

Expert servicesHatenboer-Water's service solutions

considers a vessel and equipment's entire

life span. With over a thousand units in

operation, our offshore trained service

engineers are thoroughly experienced in

keeping your system running in the most

efficient way.

Hatenboer-Water is a brand independent

specialist in water production, distribution

and disinfecting. Contacting us gives you

the benefit of reliable and expert advice.

Hatenboer-Water provides technical services from

commissioning, preventive and corrective maintenance, repair

up to major overhaul and decommissioning.


Refits or new-builds To avoid costly interventions, a sound design of your potable

water system is of imminent importance. For this reason we like

to be involved at the drafting stage.

Knowledge transferHatenboer-Water has a longstanding experience in international

knowledge transfer on drinking water: we offer hands on trainings

for system operators as well as a theoretical course. Following these

courses allows you to operate in strictly regulated areas such as

the Norwegian offshore.

Potable water courseThe Potable Water Course is suited for Engineers, Superintendents,

Medics, Health & Safety Managers, Asset Managers, etc. and gives

insight in topics like water maker technology, disinfection, sampling

and analyses and water management plans.

Hatenboer-Water is well aware of

the challenges our customers face and

the need for efficiency.

Services• Commissioning

• Surveys

• Mid-life updates

• Service agreements

• Sampling

Suitable for:• Medics

• Engineers

• Asset Managers

• Superintendents

• Health & Safety Managers

• Ship Designers

• Et cetera


Water Quality ServicesEnsuring safe water on board

Our Water Quality department acts as a consultancy and services department. The consultants deliver solutions so you can comply to international laws and to assure that your crew is working in safe conditions.

With more than thirty years of experience the Water Quality department comes forward with solutions and services that are always practical and always dedicated.


Potable Water CoursesDedicated to Maritime and Offshore p. 134

TroubleshootingSolutions on the spot p. 136

Cleaning and DisinfectionPotable water tanks & Distribution systems p. 137

Worldwide Water TestsMonitor and audit your drinking water p. 138

Water ManagementSafe water on board p. 140

For more information please contact: The Netherlands T +31 (0)10 409 12 00

Singapore T +65 6515 8021 e [email protected]

Key features• Compliance with NIPH and Ship

Sanitation• Experienced trainers• Water treatment solutions• Disinfection principles• Awareness of health risks• Testing & analyses characteristics

Potable Water CoursesDedicated to maritime and offshore

Training is of paramount importance to understand how a potable water system works and how safety and quality of potable water can be ensured.

Several regulations state that the responsible party shall ensure that everyone who carries out work on its behalf has the competence necessary to carry out such work in a prudent matter. Hatenboer-Water will provide the required knowledge with the unique Potable Water Course dedicated for maritime and offshore personnel.

What to expect?Participants will learn all about water treatment and water management onboard, leaving them with valuable knowledge on how to maintain a good and healthy water system.

A dedicated water flow chart for maritime and offshore situations will be available and is used as a guideline throughout the course.

Why follow the course?• To comply with regulations like NIPH, MLC,

Ship Sanitation and many others• To be able to make the right selection for

water processing• To recognise possible problems and to be

able to react adequately• To understand health risks

Who should attend?In general, everyone involved in water treatment and/or water management, both in the maritime and offshore market. The Potable Water Course is suited for Engineers, Super Intendents, Medics, Health & Safety Managers, Asset Managers, Ship Designers etc.


Our water specialists have many years of experience in all water

related issues and are keen to transfer their knowledge to you.

Course outline • Introduction to the potable water system, general water management

guidelines and the risk assessment• Understanding the principles of water production and treatment• Knowledge on how to identify, with the help of the ships drawing,

the relevant and critical components and risk points• Introduction to the area of responsibility concerning the water quality,

operation and maintenance of the system• Understanding and accepting the importance of doing a high quality job

in order to maintain healthy conditions for the rest of the crew on board• A certificate will be awarded upon completion of the course.

Customised trainingsTailor-made water related training caters directly to your needs. This means that courses can be organised for groups of various sizes and with various topics. They can be designed to upgrade theoretical knowledge, like a legionella course, practical skills (operator trainings) or to introduce new technologies.

The training can vary in length and depth, ranging from a course lasting a day, to a tailored programme lasting several days in which regular components are mixed with case studies and modules you need for your operation. Tailor-made trainings can be delivered on-site, or based at Hatenboer-Water in The Netherlands or Singapore.

"Trainers and

instructions are

very helpful and

practically minded!"

(USG Energy)

"The Potable

Water Course

gave all required

information."

(Dana Petroleum)

"The course helps

to give a better

understanding of

the many aspects of

water."

(Chevron)

"Interaction with

specialists."

(Heerema Marine

Contractors)

Rated 'very Good' by our participants:

First come, first servedPlease note that we have a strict first come, first served policy. It could happen that a course is fully booked before the registration deadline at Hatenboer-Water passes. Therefore we advise to register for a course as early as possible. For large groups in company trainings are possible.

Course topics• Disinfection• Maintenance• Trouble shooting • Chemistry of water • Water maker technologies • Sampling and analysing • Water management plans

TroubleshootingSolutions on the spot

A large variety of problems can occur with potable water on board. Troubleshooting is often a process of elimination, eliminating potential causes of a problem. Solving these problems can be challenging work.

Contact Hatenboer-Water to provide swift support during malfunctions, problems with potable water quality, regulations and all other kinds of water related issues. The consultants and engineers of Hatenboer-Water have a wealth of experience due to the hundreds of ships and rigs we monitored over the last few decades.

Key features• Decades of experience in solving

various water related problems • Custom made solutions• All solutions in compliance with

applicable regulations • Offshore trained Service Engineers

and Water Quality Consultants• Keep your business running

A problem is initially described as symptoms of malfunction.

Troubleshooting is the process of determining the causes of

these symptoms.

Problem solvingSolutions can vary from temporary solving problems to avoid further costs (or consequences) to cleaning the piping system, depending on the circumstances and your wishes. Hatenboer-Water is strong in assessing/isolating specific causes and solving problems to a degree that is really needed: practical and affordable containment.

Please let us help you and contact our Water Quality department for more details when you are facing troubles.

Most common nonconformities • Sedimentation, corrosion, biofouling• Deviations in water analyses• Physical, chemical and/or biological

contamination• Water safety plans/manual• System failures

For more information please contact: The Netherlands T +31 (0)10 409 12 00 e [email protected]



Cleaning and DisinfectionPotable water tanks & Distribution systems

During operation, sediment and biofilm will settle in the tanks and distribution system, becoming an ideal growth environment for microbes. Therefore the tanks and distribution system need to be cleaned and disinfected on a regular base.

Cleaning and disinfection of the complete system needs to be carried out before the vessel leaves the yard, after repairs or in case of nonconformities.

The specialists from Hatenboer-Water can assist in the cleaning and disinfection of the system. The services we can provide:

• Tank/system inspection• Status report and custom made advice• Disinfection procedure including on site measurements • Water analyses before and after the procedure

Key features• Decades of experience in solving

various water related problems • Care for the environment• Approved disinfectants• All solutions in compliance with

applicable regulations • Offshore trained Service Engineers

and Water Quality Consultants• Keep your operations running

For more information please contact: The Netherlands T +31 (0)10 409 12 00 e [email protected]


Worldwide Water TestsMonitor and audit your drinking water

Hatenboer-Water provides worldwide sampling, analysis, quality reports and on board audits to assess the chemical, microbiological and physical condition of your water to provide information on possible health risks onboard. Water samples have to be taken to assess actual status of the potable water.

Test kitsAs specialist in water, Hatenboer-Water composed dedicated test kits to ensure that you can comply with regulations once you have a specific test kit on site or on board (See chapter 6). In doubt whether your situation stands up to the authorities? Please consult our Water Quality Department.

Quality Monitoring ProgrammeHatenboer-Water offers a comprehensive water quality monitoring programme for your ship, vessel or rig. This enables you to monitor and audit the condition of the (drinking) water or the performance of the water treatment system. Our team can provide assistance in testing, monitoring and analysis, with a wide range of services including:

• Planning and programming of sampling• One-off, regular or seasonal sampling in

accordance with applicable flag state• Sampling of drinking water, cooling water,

boiler water and sewage effluent• Detailed scientific analysis and interpretative

reporting• Liaison with statutory and regulatory bodies

SamplingQualified personnel take samples according to the current standards for water examination. Special (sterilised) laboratory bottles are being used. If for practical reasons this is not possible and the sampling has to be carried out by your own personnel, sampling need to be done according to our written procedures for sampling using the appropriate laboratory bottles; these can be sent to your location on request.

Key features• All analysis are accredited• Compliance with regulatory requirements• Fully detailed reports• Professional assistance possible to the

extend you need• Advantages of monitoring programme• Reduced contract rates are possible


Water Quality Service Contract:Please ask our Water Quality department for the advantages of our Water Quality Service Contract, in which reduced rates are applicable for sampling and analyses.

Such a contract offers certainty and convenience on the basis of a professional and expert approach. Hatenboer-Water can provide you with a total package, from sampling to clear (periodic) reporting.



Ad-hoc and standard testsHatenboer-Water offers several standard tests of your water, according to your needs. In addition to the following examinations, we also deal with specific requests for analysis and advice concerning (drinking) water:

Standard bacteriological examinationTo test the general condition of the water Hatenboer-Water provides a standard bacteriological examination. This comprises of an analyses of the total bacteria count and a few common pathogenic organisms:

• Coliform bacteria at 37°C• E. coli (Escherichia) at 44°C• Intestinal enterococci

This type of examination is required by the WHO, Ship Sanitation. Additional analyses might be required depending on the situation on board and the applicable regulations.

Legionella spp examinationLegionella can grow in stagnant and warm water, especially when biofilm has been formed in the piping. Unfortunately, this is a common problem on board. The health risks that Legionella bacteria can cause are severe. Regular examination for Legionella on board can help identifying the risk in an early stage. To prevent Legionella and assure good water quality all together by good water management, check our 'Water Management Plan' (RA&MP).

Physical-chemical examinationIn a physical-chemical analysis, the drinking water is examined for several (in)organic parameters, such as salts and metals. The parameters of these analyses depend on the issue on board. Specific complaints such as abnormal odour, appearance or taste of the water, or calamities determine the required analysis. The parameters for such testing are generally determined on a case-by-case basis in agreement with the client.

Chemical examinations (Hydrocarbons)This is a specific analysis to determine the presence of a wide range of volatile organic substances (for example solvents) in the (drinking) water. This analysis often follows after regular complaints about the taste and/or smell (solvents, paint, coating) of the drinking water, e.g. after the coating of a drinking water tank has been renewed.

Together with the clearly presented results the analysis report contains

recommendations if applicable.

All tests are made in accordance with international standards

for drinking water examination, in an accredited laboratory.

Water ManagementSafe water on board

The purpose of water management is to ensure delivery of sufficient, good and safe potable water. Evidently a good design of the water system is the starting point. Water management covers implementation of routines for operation, control and maintenance. Routines that are an essential part of every HSE procedure to ensure optimal working conditions on board.

Hatenboer-Water has a department dedicated to Water Quality. It is our goal to increase the safety of your crew and the quality of your potable water system.

Key features• Compliance to applicable regulations • Safe water on board• Tailor-made• Experienced consultants• Worldwide successes

Assesssystem

Measure / Surveillance

evaluate risks

Water Safety Plan

Manage

We offer consultancy services for existing systems and for new builds. Our vast maritime and offshore experience - over 2.000 systems worldwide - guarantees that we can provide you with practical advices that can easily be incorporated, ensuring safe water on board and in full compliance to applicable regulations.

Our water specialists have many

years of experience in all water

related issues and are keen to

transfer their knowledge to you.


With more than 30 years of experience our Water Quality

department comes forward with solutions and services

that are always practical and always dedicated.

Preliminary Risk AssessmentsA preliminary risk assessment is based on the P&ID and other ship drawings. Hatenboer-Water offers consultancy services for ship designers and yards on the specific piping and system lay-out for new buildings in order to ensure good water quality and compliance with the relevant regulations.

Risk AssessmentsDuring a risk assessment an inventory of the possible risks is made concerning the drinking water quality and the condition of the drinking water piping system. Hatenboer-Water experts compare the entire water system from production to consumption as shown in the drawings and the actual situation on board. During the inspection, areas of risks that are present on board are assessed. The risk assessment is concluded by an improvement plan and a management plan.

Potable Water ManualsA potable water manual contains the risk assessment and guidelines for the operation, maintenance and control of the potable water system. Hatenboer-Water can assist in outlining, or drawing up, the complete guidebooks for your potable water system. As a result, you will always have the relevant data at hand in one document. The included procedures assist in the planning, preparation and performance of your operations, all in accordance with the required regulations.

Water Quality Service Contract:Please ask our Water Quality department for the advantages of our Water Quality Service Contract, in which reduced rates are applicable for sampling and analyses.

Such a contract offers certainty and convenience on the basis of a professional and expert approach. Hatenboer-Water can provide you with a total package, from sampling to clear (periodic) reporting.



Survey of your potable water system A survey can be a technical analysis of equipment; a check of your manual or management plan in case of nonconformities. With our extensive experience and knowledge our consultants are quick in recognising nonconformities in regards to procedures or compliances with regulations.

Management Plans (Administrative Control Plans)Every Management Plan is tailor-made after a visit on board by one of our qualified drinking water experts (Risk Assessment). The Management Plan is an administrative control plan and forms an essential part of any HSE procedure. Evidently is it wise to embed surveillance, to monitor the effectiveness of procedures and measures taken.

Regulatory complianceWith extensive experience of auditing projects worldwide over the last 30 years, Hatenboer-Water has the knowledge to know the differences in regulations. To check whether your water system and management stands up to applicable regulations, our consultants will evaluate your Management Plan.

Audit of your existing management plan With our extensive knowledge and experience Hatenboer-Water is quick in recognising nonconformities in regards to procedures, measures and measurements. An audit will give you an independent evaluation of the implementation of your water management plan.

Problems you can encounter• Corrosion• Biofilm• Bacteriological contamination• Physical-chemical contamination• Problems with coatings

of drinking water tanks• Various other issues that might be

a threat to your crew’s health

You can consult Hatenboer-Water regardless the challenges you are facing with your potable water system, from source through treatment to the point of consumption.

Water systems can be upgraded to

a safe system by implementing our

improvement plans.


As water is a unique and many-sided product, problems with water are multifarious like scale, bacteria, lack of water, problems with odour and taste, corrosion etc. As a consequence, it is imperative to have knowledge of the different processes in water production, conservation, distribution and storage.


Technical Services For optimised operating processes

Safe water on board starts with proven water treatment equipment and a sound design of your potable water system, but even the best equipment needs regular maintenance. Hatenboer-Water can train your staff to maintain the equipment. Furthermore, Hatenboer-Water provides technical services from commissioning, preventive and corrective maintenance, repair up to mayor overhaul: to support you during all phases of the life cycle of your system.


Survey of your Water SystemMake sure your water system is functioning properly p. 146

Service AgreementsOptimising your operations p. 147

Mid-life Updatesextending the life span of your equipment p. 148

Cold StackingMothballing your water maker p. 149

Operator TrainingsHands-on training in the workshop or on-site p. 150

Survey of Your Water SystemMake sure your water system is functioning properly

A survey of your water system is an analysis of how the water production, distribution and disinfecting system are functioning on board. With over a thousand units in operation, our offshore trained service engineers are thoroughly experienced in recognising possible system inefficiencies.

The survey report gives you a detailed insight in the state of the system, the expected maintenance costs and savings to be made.

Reasons for a preventive inspection of your Reverse Osmosis system:• Save money; prevention of unnecessary

downtime or excessive wear• Optimising the water quality/production• Keep your RO unit running according to the

required standards• Reduction of maintenance costs

Duration of the survey2 - 3 days (1 man) survey on site

How can you applyIf you are interested in a system survey, please contact our Service Department: The Netherlands T +31 (0)10 409 12 00


What can you expect• Overall quality check of your RO system including:

• Verification of logsheet data (process data)• Verification of all process functions• Check of all alarms• Monitoring and adjusting of setpoints

• Accredited analysis of the RO product water• Training of (possibly new employed) operators• Performance survey report:

• Advice on operational reliability• Advice on optimisation of water production and quality• Results of water analysis• Overview of work performed

• Determination of expected required spare parts


Duration of the agreementSubject to any time

How can you applyPlease contact our Service Department to discuss your maintenance needs. The Netherlands T +31 (0)10 409 12 00


What can you expectOur service agreement is customised to your needs, but we advise a yearly service visit. During a scheduled maintenance visit, our offshore trained service engineers will perform:

• Interview the designated technician(s) regarding the status of the unit; addressing any known faults

• Administrative check; does the unit still comply with the P&ID

• Operational running check; does the unit still function within design spec

• Evaluation of administrative and operational check; prioritising tasks

• Corrective and preventive maintenance according to the checklist

• Calibrating instruments• Chemical cleaning of the membranes• Completion of service as required• Operational and maintenance training

of the staff • Spare parts inventory check and advice

While servicing the unit, all findings and results will be noted in a report and handed over.

Service AgreementsOptimising your operations

Next to services like surveys, risk assessments for Legionella or mid-life updates, Hatenboer-Water offers you a service agreement. The starting point for Hatenboer-Water is always the same: to keep your water production and treatment system at the lowest possible cost in optimum condition, without compromising the reliability of the system and the water quality.

Every unit supplied by Hatenboer-Water has a free of charge Log Sheet Control service included. When you provide us with the key parameters of the unit, we will check if the unit is running within spec and which preventive maintenance needs to be performed.

Keeping your systems on board running as efficient as possible is a challenge and even the most robust units need attention. On board technology becomes more complex and crews get smaller as a result maintenance becomes more demanding. Hatenboer-Water offers you and your crew service on a regular basis to maintain Safe Water on Board.

Reasons for concluding a service agreement: • Priority scheduling• Reduction of the maintenance budget• Pro active approach for maintaining system

integrity• Special rates

Mid-life UpdatesExtending the life span of your equipment

When you want to upgrade the potable water system on board, Hatenboer-Water can of course be of assistance. Not only with surveying your system, but also with offering specialised services to enhance your system. This implies that your crew can focus on other important jobs.

Our service engineers are all-round maintenance specialists and they can optimise your reverse osmosis water makers quickly and with full awareness of having safe water on board. As you are operating in a highly demanding business. We will make sure your water system is operational at all times.

Over the years the crew on a vessel or rig has sized down, the operational location has changed or the water system is near its end of life. In all examples it is wise to amend the configuration of your water system. Extending the life span of your systems reduces the need for capital investments.

Reasons for a mid-life update: • Sized down/up crew• Changed operational location• Wish to extend the life span• Optimise water production• Reduction of your capital investments and/or

operational expenditures• Ensure safe water on board

Duration of the updateDepending on the type of system

How can you applyIf you are interested in a mid-life update, please contact our Service Department: The Netherlands T +31 (0)10 409 12 00


What can you expectThe mid life update starts with a general assessment of the operational quality of the system. During this assessment a list of improvement points will be drawn up and prioritised.

A survey report will be presented to you with all related improvements, costs and time planning for your consideration. After finalising the upgrade, local staff will be trained to operate and maintain the upgraded system in the most efficient way.

Depending on what water system you have on board, the Hatenboer-Water service engineers can handle all equipment involved in the water production, distribution, filtration or disinfection, like the hydrophore unit for the distribution of drinking water, the hot and or cold water system or the water maker on itself. Always with the intention to enable clients to make optimal use of their equipment.


Cold StackingMothballing your water maker

During ‘Cold Stacking’ of a rig, vessel or platform it will be docked at port and essentially shut down. This means the water maker system will be out of service for a longer period. To prepare your system during this period, we advise to mothball your complete water maker system.

Our dedicated service engineers are all offshore certified and specialised in the maintenance of water treatment systems. They can perform a conservation of your water maker system in a competent manner. This means that your crew can focus on vessel specific items.

The conservation of the fresh water maker system reduces costs for maintenance and attention during the ‘cold stacking’ period of the rig, vessel or platform and is to smooth up the progress for the future re-commissioning of the system.

Cold stacking of a rig is similar to ‘shuttering’ an industrial plant – it involves ‘storing’ the rig in a port or shipyard. The crew is reduced to (almost) zero to minimise costs.

Reasons for mothballing your water maker system:• Save money; prevention of bacterial growth in

your water maker system• Prevent unnecessary maintenance and

attention• Keep your water maker in a good condition• Have insight in expected costs• Operate according the required standards at

re-commissioning

Duration of cold stacking2 days (1 man) on-site

How can you applyIf you are interested in cold stacking, please contact our Service Department: The Netherlands T +31 (0)10 409 12 00


What can you expectComplete mothballing of your water maker system including conservation of:

• Multi Media Filter• Dosing systems (Anti-scalant, Hadex®)• Feed pump, High Pressure pump and Clean in Place pump• Membranes and Cartridge filters• Piping• Mineralising filter • UV disinfection system ‘Cold Stacking Report’ including:

• Overview of work performed• Advice on operational reliability for re-commissioning• Determination of expected required parts for re-commissioning

System Operator TrainingHands-on training in the workshop or on-site

Safe water on board starts with proven water treatment equipment and a sound design of your potable water system, but even the best equipment needs regular maintenance. For that reason, Hatenboer-Water developed hands on training and instruction courses for System Operators.

Next to providing trainings, Hatenboer-Water provides technical services from commissioning, preventive and corrective maintenance, repair up to mayor overhaul. Hatenboer-Water supports you through the complete lifecycle of a system. Please let us know how we can support you to maximise uptime of your equipment.

Benefits of the operator training:• Secure safe water on board• Reduce maintenance costs• Expanding knowledge • Prevent unnecessary downtime• Comply with regulations• Safe operating of your equipment

For whom:• Operators• Maintenance Engineers• Chief Engineers

Duration of the training1 - 2 days

How can you applyIf you are interested in an Operator Training please contact our Service Department: The Netherlands T +31 (0)10 409 12 00


What can you expectEvery course is made to measure for your particular equipment and situation. Our operator training goal is to increase the knowledge regarding water treatment, learn safe operating techniques and discover how to maximise machine productivity. Instructions in proper operating techniques, daily service checks, proper startup/shutdown procedures, machine controls, and safe operating techniques to minimise downtime. The course comprehends classroom and/or hands-on exercises.


CatalogueIndex

A

Acid membrane cleaner chemicals

Activated carbon filter cartridges, HAC

Activated carbon filter media

Administrative control plans, Water Quality Services

Alkaline granular filter media EWT compound

Analysing services, Water Quality Services

Anthracite, filter media

Anti scalant ECO chemicals

Aquality, water coolers

Audits of management plans, Water Quality Services

BBack flow preventers, Kemper

Based sodium hypochlorite digital test kits (Hadex®)

Based sodium hypochlorite manual test kits (Hadex®)

Big Blue filter housings

Boiler water test kits

Boilers

CCalciumhypochlorite tablets TS70/TS90

Calorifiers

Carbon block Fibredyne filter cartridges, Everpure

Carbon block HWCB filter cartridges

Carbon block Microguard filter cartridges, Everpure

Cartridges POU for HIS filter housing, Supercarb

Cartridges POU filters Everpure

Cat high pressure pumps

Cation/anion mixbed resin

Chemicals, acid membrane cleaner

Chemicals, alkaline membrane cleaner

Chemicals, anti scalant ECO

Chlorination tablets SANURIL 115

Chlorination tablets TS70/TS90

Chlorination tablets TS90

Claris / Claris Ultra Everpure POU filters

Claris Everpure POU filter heads

Cleaner membrane alkaline, chemicals

Cleaning and disinfection of tanks and distribution system, Water Quality Services

Cold and hot water modules, Custom built

Coldstacking, Technical Services

Complete fresh water test kits for maritime use

Complete fresh water test kits for offshore industry

Conductivity testers

Cooling water test kits

Copper silver ionisation, LiquiTech™

84

67

71

142

71

138

71

84

142

142

59

97

98

65

105

115

83

115

123

68

124

120

123

57

72

84

84

84

83

83

83

125

125

84

137

22

149

94

93

109

107

43

Corrosion containment fluid, dosing units

DDemineralisers Demiflow HDF

Demitec® UV disinfection units

Desalination membranes

Dolomite mineralising filter media

Dosing units for fluids to contain corrosion

Dosing units for Hadex®

Dow Filmtec, desalination reverse osmosis membranes

eEverpure POU filters

Everpure POU filter heads

Everpure reverse osmosis POU systems MRS-600HE

EWT compound filter media

FFibredyne carbon block POU cartridges filters, Everpure

Filter bags with snap-ring

Filter bags X100B

Filter cartridges activated carbon, HAC

Filter cartridges carbon block, HWCB

Filter cartridges sediment, HWMB

Filter cartridges Supercarb for POU HIS housing

Filter cartridges X100C

Filter heads POU Everpure

Filter housings Big Blue

Filter housings for single bag

Filter housings for X100B/X100C

Filter housings POU for HIS cartridges

Filter housings, plastic 113 / 213

Filter media, activated carbon

Filter media, anthracite

Filter media, Dolomite minerals

Filter media, EWT compound

Filter media, gravel

Filter media, sand

Filter POU cartridges Everpure series

Filter POU heads cartridges Everpure

Filters galley/shower Legionella UF, T-Safe®

Filters Big Blue melt blown

Filters Everpure POU series

Free chlorine test strips

Fresh water generator Oceanus RO type standard series

Fresh water generator Proteus RO type standard series

Fresh water generators custom built

80

87

39

69

72

80

34

69

123

125

127

71

123

69

69

67

68

67

120

68

125

65

65

63

120

64

71

71

72

71

72

72

123

125

120

68

125

98

27

28

20

G

Galley/shower Legionella filters UF, T-Safe®

Granular alkaline filter media EWT compound

Gravel

Grundfos pressure boosting system, Hydro MPC

Grundfos pumps

HHAC filter cartridges activated carbon

Hadex® drinking water disinfectant

Hadex® dosing units

Hadex® digital test kits

Hadex® manual test kits

Hadex® test strips

Hadex® stock points

HDCF housings for fine or activated carbon filter cartridges

HDF Demiflow demineralisers

HIS POU filter housings

Hot and cold water modules

Housings for Big Blue filter

Housings for fine or activated carbon filter cartridges, HDCF

Housings for single bag filter

Housings for X100B/X100C filters

Housings POU for HIS filter cartridges

Housings, plastic for filter cartridges 113/213

HWCB carbon block filter cartridges

HWMB sediment filter cartridges

HWSIS silver ionisation

HWS-SCA softeners

Hydranautics, desalination/reverse osmosis membranes

Hydrophore vessels

Hygicult test kits with incubator

KKemper back flow preventers

Kugaokeanos mineraliser additive

LLegionella galley/shower filters UF, T-Safe®

LiquiTech™ copper silver ionisation

MManagement plans drawing up, Water Quality Services

Manuals potable water drawing up, Water Quality Services

Membrane acid cleaner, chemicals

Membrane cleaner alkaline, chemicals

Membrane tanks hydrophore

Membranes reverse osmosis

Meters handheld, conductivity

120

71

72

50

49

67

33

34

97

98

98

12

63

87

120

22

65

63

65

63

120

64

68

67

45

89

69

53

95

59

85

120

43

142

141

84

84

53

69

109


Meters handheld, pH

Meters handheld, temperature

Meters, turbidity

Microguard carbon block cartridges filters, Everpure

Mid-life update, Technical services

Mineralising filters HDN

Mineralising filter media Dolomite

Mineralising kugaokeanos

Mixbed resin, cation/anion

Mothballing, Technical Services

N

Neutralising filters HDN

O

Oceanus reverse osmosis water maker standard series

Operator trainings

P

pH handheld meters

Potable water courses, Water Quality Services

Potable water disinfectant

Potable water manuals drawing up, Water Quality Services

Potable water stabiliser dosing units

POU filter cartridges Everpure series

POU filter heads Everpure

POU filter cartridges Supercarb for HIS housing

Precoat cartridges POU filters, Everpure

Preliminary risk assessments, Water Quality Services

Pressure boosting system, Grundfos Hydro MPC

Proteus reverse osmosis water maker standard series

Pumps, Cat, high pressure series

Pumps, Grundfos series

PWT testing equipment, conductivity

R

RA&MP, Water Quality Services

Regulatory compliance checks, Water Quality Services

Resin, cation/anion mixbed

Reverse osmosis membranes

Reverse osmosis POU system, Everpure MRS-600HE

Risk assessment & management plans, Water Quality Services

Risk assessments, Water Quality Services

Risk assessments preliminary, Water Quality Services

River, water coolers

109

110

111

124

148

77

72

85

72

149

77

27

150

109

134

33

141

80

123

125

120

123

140

50

28

57

49

110

141

142

72

69

127

141

140

140

119

S

Sampling, Water Quality Services

Sand

Sanuril 115, chlorination tablets

Scale control cartridges filters, Everpure

SD50 testing equipment, pH

SD70 testing equipment, conductivity

Sediment filter cartridges, HWMB

Service agreements

Services, audits of management plans

Services, cleaning and disinfection of tanks and distribution system

Services, coldstacking/mothballing

Services, management plans

Services, mid-life updates

Services, preliminary risk assessments

Services, regulatory compliance checks

Services, risk assessments

Services, sampling

Services, service agreements

Services, surveys

Services, troubleshooting

Services, water testing

Sewage effluent basic testers

Sewage effluent test kits, digital

Sewage effluent test kits, standard

Shower Legionella filters UF T-Safe®

Silver Ionisation HWSIS

Sodium hypochlorite disinfection liquid

Softeners

Solutions, custom built for desalination, disinfection, distribution, heating

Stabiliser dosing unit

Stabiliser potable water 445+

Stockists Hadex®

Supercarb cartridges for HIS filter housing

Surveys potable water system

Surveys water maker

T

Tablets Sanuril 115, chlorination

Tablets TS70 chlorination

Tablets TS90 chlorination

Test kit Hygicult with incubator

Test kits for based sodium hypochlorite, digital

Test kits for based sodium hypochlorite, manual

Test kits for boiler water

Test kits for cooler water

Test kits for maritime industry (NIPH/MLC)

Test kits for offshore industry (NIPH/MLC)

138

72

83

124

109

109

67

147

142

137

149

142

148

140

142

141

138

147

142

136

138

103

101

102

120

45

33

89

16

80

85

14

120

142

146

83

83

83

95

97

98

105

107

94

93

Test kits, digital, for sewage effluent

Test kits, Hadex® digital

Test kits, Hadex® manual

Test kits, standard, for sewage effluent

Test strips free chlorine

Test strips Hadex®

Tester handheld, conductivity

Tester handheld, conductivity PWT

Tester handheld, pH

Tester, temperature

Tester, turbidity

Testers basic, for sewage effluent

Testing services misc, Water Quality Services

Testing services, bacteriological examinations

Testing services, chemical examinations (Hydrocarbons)

Testing services, legionella spp examinations

Testing services, physical-chemical examinations

Thermometers

Toray, reverse osmosis membranes

Training dedicated to operators

Training potable water to comply with regulations

Troubleshooting services

TS70/TS90 chlorination tablets

T-Safe® Legionella tappoint filters

Turbidity meters

U

Ultra violet disinfection units Demitec™ Beta Line (BL/BM)

Ultra violet disinfection units Demitec™ Gamma Line (GS)

Ultra violet disinfection units Demitec™ NIPH (BLE/Kappa Line)

W

Water Coolers

Water maker Oceanus reverse osmosis type standard series

Water maker Proteus reverse osmosis type standard series

Water maker surveys, Technical Services

Water management services misc.

Water softeners

Water testing, Water Quality Services

X

X100B filter bags

X100C filter cartridges

101

97

98

102

98

98

109

110

109

110

111

103

138

138

138

138

138

110

69

150

134

136

83

120

111

40

39

41

119

27

28

146

140

89

138

69

68

Copyright © 2016 by Hatenboer-Water

All rights reserved. No part of this publi-

cation may be reproduced, distributed,

or transmitted in any form or by any means,

including photocopying, recording, or other

electronic or mechanical methods, without

the prior written permission of the publisher,

except in the case of brief quotations

embodied in critical reviews and certain

other non commercial uses permitted by

copyright law. For permission requests,

write to the publisher:

HATeNBOeR-WATeR BVAttention PR Department PO Box 6013 3002 AA Rotterdam The Netherlands

Hadex® and Demitec® are registered

trademarks of Hatenboer Water BV.

Our trademarks may only be used with

Hatenboer-Water’s written permission.

We have compiled this catalogue with great care but we reserve the right to make changes in the future with respect to the content of this catalogue. For the impact of misprints or mistakes no liability is accepted.

Hatenboer-WaterProclaimer

Hatenboer-Water bv Mercuriusweg 83113 AR SchiedamP.O. Box 60133002 AA Rotterdam The Netherlands

e [email protected] +31 (0)10 409 12 00

Hatenboer-Water asia Pte LtD22 Boon Lay Way#01-57 Tradehub 21Singapore 609968

e [email protected] +65 6515 8021

www.hatenboer-water.com

ISO 9001 ISO 14001 VCA*

Your benefits choosing Hatenboer-Water• Safe water on board, meaning a safe working

environment for your crew

• Good water from production to consumption

• Strong focus on service, quality, innovations and improvement

• Minimal downtime

• Easy access to spare parts and consumables

• Worldwide services

• Local, skilled, support

Hatenboer-Water in a nutshell• More than 100 experienced professionals

• Based in the Netherlands and Singapore

• All disciplines and facilities under one roof

• Fully stocked warehouses for short delivery times

• In-house engineering, 3D CAD design

• Continuous R&D

• Fully equipped workshop

Hatenboer-WaterYour partner in maritime water treatment & services

safe Water on board Catalogue 2016 Providing your w

ater from production to consum

ption

Distributor/agent:

Pro

du

ct C

ata

logu

e H

ate

nb

oe

r-W

ate

r-U

K 2

016

-1

Date post:	12-Feb-2022
Category:	Documents
Upload:	others
View:	4 times
Download:	0 times

SAFE (DRINKING) WATER ON BOARD

Documents