Safety advantage 1 · STAHLWILLE QuickRelease-System STAHLWILLE AS-Drive Safety advantage 1 Safety...

ß Hand tools

eng/OP www.hhw.de 51.1

5

STAHLWILLE QuickRelease-System

STAHLWILLE AS-Drive

Safety advantage 1

Safety advantage 2

Problem: During general maintenance work in a hard-to-reach place a tool is lost.Effect: Time-consuming and cost-intensive search, perhaps even a complete disassembly e.g.of an engine or a machine.The solution:The safety lock of the QuickRelease system prevents damage to workpieces andguarantees a secure and quick connection between all components and creates a firmunit.Nothing will be lost because accidential loosening of single tools is excluded. Toseparate the tools, the user first has to push a button. Even with oily hand, the easy handling and therefore effortless connecting and discon-necting of the tools immensely facilitates the work.

Problem: For loosening very corroded screws, an extreme high force is necessary. The socket wrench will slip off.Effect: Injuries and damage to workpiece and tool because of unchecked operation.The solution:STAHLWILLE socket wrench bits are equipped with the AS-Drive* profile. It ensures highforce transmission to the flanks of the screws and nut, without damaging them.This lowers the risk of injury and the edges of the screwsremain intact.

*Anti-Slip-Drive

Safety advantage 3STAHLWILLE HPQ socket wrench bitsProblem: In spite of limited space, high torques are asked for.Effect: Many socket wrench bits can not be used because their wall thickness makes working under such conditions impossible.The solution:STAHLWILLE HPQ* socket wrench bits are made from a selected strength-hard steel allow. Neither do they slip nor do they become wider under load. Their extremely thin walls at highest load capacity are unparalleled. HPQ socket wrench bits are free of cadmium and are therefore suitable for working withtitanium-alloyed parts and titanium combination elements e.g. in the aviation industry,where security is of paramount importance. The fulfil the following aviationstandards: E DIN EN 3709, E DIN EN 3710, SAE AS 954-E, S.B.A.C. AS 40605/40606, MS-33787, MIL-W-8982.

*High Performance Quality

Wrench size and squareend of the cold-extrudedsocket wrench bits havevery narrow tolerances,comparable to broachedtools. Therefore, thetools will not slip overthe edges of the screws. Effect: Low wear of screw and tool.

STAHLWILLE socketwrench assortments areavailable not only in thetested and proven metalcases, but also in thenew and robust plasticcase.

STAHLWILLE QuickRelease system

STAHLWILLE AS-Drive

eng/OP

• Socket Wrench Sets

www.hhw.de51.2

5

Set of hexagonal socket wrenches

0Type18-part, in sheet steel box with foam insert. All toolsare stored vibration-free.

QualityChrome-vanadium steel.

51002

Set contents 51002 …

18-part 101

51002


Type17-part, in metal case.

QualityChrome-vanadium steel. 51005

Set contentsN 11 hexagonal bits, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,

1 reversible ratchet, 135 mm,1 handle with sliding piece, 115 mm,1 handle with joint with borehole for straight shaft 150 mm,1 straight shaft 115 mm,1 ea. extension 75 mm and 150 mm.


17-part 201

51005

Set contentsN 13 hexagonal bits with Energy profile, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,

1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 ea. extension 50 mm and 105 mm.


NType16-part, in impact-proof plastic box with PUR insert.

QualityVanadium 31CrV3. 51008

51008

Set contentsN 11 hexagonal bits, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,

1 reversible ratchet,1 handle with sliding piece,1 bit holder with plastic handle,1 Cardan joint,1 extension 97 mm.


16-part 101

Set of hexagonal socket wrenches51009

Type19-part, chrome-plated, in sheet steel box, in TCSinserts.

QualityChrome-alloy steel.

Set contentsN 13 hexagonal bits with AS-Drive profile size 3,5 / 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,

1 reversible ratchet, 1 bit holder with plastic handle, 1 handle with sliding piece, 1 ea. extension 54 and 150 mm 1 Cardan joint.


19-part 105

51009

ß Hand tools


5


VType20-part, in plastic box.


Set contentsN 13 hexagonal bits, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,

1 reversible ratchet,1 handle with sliding piece,1 bit holder with plastic handle,1 Cardan joint,1 ea. extension 55 mm and 147 mm.1 handle with joint.


20-part 101

51011


JType13-part, in plastic box.


51014

Set contentsN 10 socket wrench bits OGV® profile, size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,

1 reversible ratchet,1 bit holder with plastic handle,1 extension 100 mm.


13-part 301

Set of hexagonal socket wrenches (inch)

VType14-part, imperial sizes, in plastic box.


Set contentsN 8 hexagonal bits, 3/16 / 7/32 / 1/4 / 9/32 / 5/16 / 11/32 / 3/8 / 7/16,

1 reversible ratchet,1 handle with sliding piece, 1 bit holder with plastic handle1 Cardan joint, 1 ea. extension 55 and 147 mm.

51020


14-part 201

Set of double hexagonal socket wrenches51021

NType17-part, in plastic case.


Set contentsA 11 double hexagonal bits with UD profile size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,

1 reversible ratchet,1 handle with sliding piece,1 multi-handle with non-slip 2-component handle and inner square in compliance with DIN 3120-C6,3 (1/4 inch),1 Cardan joint,1 extension 97 mm1 adapter 1/4 inch outer hexagonal solid x 1/4 inch outer square solid


17-part 101

eng/OP


www.hhw.de51.4

5

Set of socket wrenches TRIPLEplus

0Type 40-part, mirror finished and chrome polished, inABS plastic box.

Application Multi-purpose use screwing system for hexagonal,double hexagonal, and E-TX screws and nuts. Fitsall standard imperial sizes. Quality Chrome-vanadium steel.

51022

) N A N G

mm hexagonal double hexagonal inch E-TX4,0 x x 5/32 E 54,5 x x – E 65,0 x x 3/16 –5,5 x x – –6,0 x x – E 87,0 x x 9/32 –8,0 x x 5/16 E 109,0 x x 11/32 –

10,0 x x 3/8 E 1211,0 x x 7/16 E 1412,0 x x 15/32 E 1613,0 x x 1/2 –14,0 x x 9/16 E 18

Set contents13 socket wrench bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm (cat.-no. 51072),

M 7 bits for TORX® screws T 10 / 15 / 20 / 25 / 27 / 30 / 40, E 2 bits for Phillips recess head screws PZ 1 / 2,D 2 bits for Phillips recess head screws PH 1 / 2,J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 7 / 8 mm,H 5 bits for XZN Trisquare socket head screws M 4 / 5 / 6 / 8 / 10,

1 reversible ratchet (cat.-no. 51127 101), 1 bit holder with plastic handle, 1 extension 100 mm1 Cardan joint,1 adapter 1/4inch . / 1/4inch N (cat.-no. 52938 101).


40-part 101

51022

Set of double hexagonal socket wrenches

NType29-part, in plastic case, 275 x 150 x 42 mm.



29-part 201

51037

Set contentsA 12 double hexagonal bits with UD profile size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,

10 double open-end wrenches, heads offset 15° and 75°, size 4 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,1 reversible ratchet, 1 Cardan joint,1 ea. extension 55 and 97 mm,1 connecting piece, outer hexagon 1/4inch x outer square 1/4inch,1 multi-purpose handle, Allen key mount 1/4inch,1 multi-purpose holder for nuts and washers, M3 - M8.

Performance requires quality.www.atorn.com

Screwdrivers by ATORN:

ATORN‘s high-quality hand tools.

ß Hand tools


5Set of hexagonal socket wrenches

Type 29-part, in plastic box.

Quality Chrome-vanadium steel.

51024

Set contentsN 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm, Q 3 bits for slotted screws 4 / 5,5 / 7 mm,D 2 bits for Phillips recess head screws PH 1 / 2, E 2 bits for Phillips recess head screws PZ 1 / 2,

1 reversible ratchet with ejection device, 1 bit holder with plastic handle, 1 handle with sliding piece, 1 Cardan joint, 1 extension 50 mm.


29-part 201

51024


Type34-part, in plastic box.


51025

Set contentsN 11 hexagonal bits, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,Q 3 bits for slotted screws 4 / 4,5 / 5 mm,D 4 bits for Phillips recess head screws 1 / 2 / 3 / 4,J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 8 / 10 mm,

3 hexagon wrenches for Allen screws size 1,5 / 2 / 2,5 mm,1 reversible ratchet, 1 handle with sliding piece,1 bit holder with plastic handle,1 Cardan joint,1 ea. extension 50 mm and 100 mm,1 quick-action wheel.


34-part 301


0TypeIn sheet steel box with foam insert. All tools arestored vibration-free.

QualityChrome-vanadium steel. 51023 101

Set contents 51023 101N 12 hexagonal bits with Energy profile, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,J 5 bits for Allen screws, size 3 / 4 / 5 / 6 / 8 mm,D 2 bits for Phillips recess head screws PH 1 / 2,E 2 bits for Phillips recess head screws PZ 1 / 2,Q 3 bits for slotted screws 0,8 x 4 / 1,0 x 5,5 / 1,2 x 6,5 mm,

1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 extension 50 mm.

51023 102

51023

Set contents 51023 102N 13 hexagonal bits with Energy profile, size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,N 4 hexagonal bits, long type, with Energy profile, size 8 / 10 / 11 / 13 mm,J 5 bits for Allen screws, size 8 / 10 / 11 / 13 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,

3 bits for slotted screws 4 / 5,5 / 6,5 mm,6 bits for inner TORX® screws, T10 / 15 / 20 / 25 / 30 / 40,1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 ea. extension 50 and 105 mm.


28-part 10142-part 102

eng/OP


www.hhw.de51.6

5


NType32-part, with forged, tempered hexagonal socketwrench bits and tools in impact-proof plastic boxwith PUR insert.


Set contentsN 11 hexagonal bits, size 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm,Q 4 bits for slotted screws 0,8 x 4 / 1,0 x 5,5 / 1,2 x 6,5 / 1,6 x 8 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,

1 reversible ratchet finely toothed,1 handle with sliding piece, 1 Cardan joint,1 bit holder with plastic handle, 1 ea. extension 55 mm and 148 mm.


32-part 201

51034

www.atorn.com

Performance requires quality.

Tool carts by ATORN:

ATORN‘s high-quality workshop furnishings.


JType 22-part, in plastic box.

Quality Chrome-vanadium steel. 51026

Set contentsN 9 socket wrench bits OGV® profile, size 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, M 6 bits for TORX® screws T10 / 15 / 20 / 25 / 30 / 40,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,

1 reversible ratchet, 1 bit holder with plastic handle, 1 extension 100 mm, 1 adapter 1/4 inch z x 1/4 N.

51026


22-part 101

ß Hand tools


5


Type Chrome-plated, in sheet steel box.

Quality Chrome-alloy steel.

Set contents 51038 101N 13 hexagonal bits with AS-Drive profile size 3,5 / 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, J 4 bits for Allen screws size 3 / 4 / 5 / 6 mm,

1 reversible ratchet, 1 bit holder with plastic handle, 1 handle with sliding piece, 1 extension 150 mm, 1 Cardan joint.

Set contents 51038 104N 11 hexagonal bits with AS-Drive profile size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm, J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm, Q 3 bits for slotted screws 0,6x3,5 / 1,0x5,5 / 1,2x8,0 mm, D 4 bits for Phillips recess head screws PH 1 / 2 / 3 / 4,

1 reversible ratchet, 1 bit holder with plastic handle, 1 handle with sliding piece, 1 ea. extension 54 and 150 mm, 1 Cardan joint.


22-part 10129-part 10436-part 107

51038 101

51038 104

51038 107

51038

Set contents 51038 107N 10 hexagonal bits with AS-Drive profile size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm, M 9 bits for inner TORX® screws T8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40,4 6 bits for outer TORX® screws E4 / 5 / 6 / 7 / 8 / 10,

1 reversible ratchet, 1 bit holder with plastic handle, 1 handle with sliding piece, 1 ea. extension 54 and 150 mm,1 Cardan joint.


TypeWith QuickRelease system (one-hand safety lock),in plastic case.

51032 101

51032 201


22-part 10130-part 201

51032

Set contents 51032 101N 13 hexagonal bits size 3,5 / 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,J 4 bits for Allen screws size 3 / 4 / 5 / 6 mm,

1 reversible ratchet,1 extension 150 mm,1 Cardan joint,1 socket handle,1 handle with sliding piece.

Set contents 51032 201N 12 hexagonal bits, size 4 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm,Q 3 bits for slotted screws 0,6 x 3,5 / 1,0 x 5,5 / 1,2 x 8 mm,D 2 bits for Phillips recess head screws PH 1, 2,E 2 bits for Phillips recess head screws PZ 1, 2,

1 reversible ratchet,1 ea. extension 54 mm and 150 mm,1 Cardan joint,1 socket handle,1 handle with sliding piece.

eng/OP


www.hhw.de51.8

5

Set of hexagonal and double hexagonal socket wrenches

Type 49-part, chrome-plated, in sheet steel box.


51039Set contentsx

N 8 hexagonal bits with AS-Drive profile size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 mm, J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm, Q 6 bits for slotted screws 0,5x3 / 0,6x3,5 / 0,8x4 / 1x5,5 / 1,2x6,5 / 1,6x8 mm, D 3 bits for Phillips recess head screws PH 1 / 2 / 3, E 1 bit for Phillips recess head screws PZ 2,

1 reversible ratchet, 1 bit holder with plastic handle, 1 extension 150 mm, 1 Cardan joint, 1 bit holder with inner hexagon 1/4 inch.

w

A 12 bits double hexagonal with AS-Drive profile size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 mm, A 1 double hexagonal bit with AS-Drive profile size 20,8 mm-13/16 inch, with rubber insert for spark plugs,N 1 hexagonal bit with AS-Drive profile size 16 mm-5/8 inch, with rubber insert for spark plugs,

1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 76 and 240 mm, 1 Cardan joint, 1 adapter 3/8inch . x 1/4 inch z, 1 bit holder with hexagon 5/16 inch.


49-part 101

51039

Set of hexagonal socket wrenches HINOX

VType24-part, in plastic case with PUR soft foam insert alltools are stored vibration-free.Up to 20% higher torque values with the HINOXseries (static load). Stainless steel for higherstrength at same hardness when compared tostandard material (31 CrV 3). More safety, lower riskof injury. Up to three times longer service life (shownin dynamic permanent-load comparison).

Environmentally friendly production without surfacecoating. No allergic reactions thanks to chemicalcoating.Considerably longer service life if compared tocompetitors' products (stainless steel instead ofcoating).Weather-resistant application outdoors.QualityStainless steel.

51045

Set contentsN 13 hexagonal bits with Tractions profile size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm, J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm,

1 reversible ratchet,1 handle with sliding piece, 1 socket handle,1 Cardan joint,1 ea. extension 55 and 147 mm.


24-part 101

51045





30-part 201

51040

Set contentsN 12 hexagonal bits size 4 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm,Q 3 bits for slotted screws 0,6x3,5 / 1,0x5,5 / 1,2x8,0 mm,D 2 bits for Phillips recess head screws PH 1 / 2,E 2 bits for Phillips recess head screws PZ 1 / 2,

1 reversible ratchet,1 handle with sliding piece,1 bit holder with plastic handle,1 Cardan joint,1 ea. extension 55 and 147 mm.

ß Hand tools


5


VType 33-part, in plastic case, 187 x 125 x 39 mm, withPUR soft foam insert. All tools are stored vibration-free.

Quality Chrome-vanadium steel. Screwdriver bits CVD-TiN-coated.

51041


33-part 101

51041

Set contents> 11 hexagonal bits with Tractions profile size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,4 5 bits for outer TORX® screws E 5 / 6 / 7 / 8 / 10,J 4 bits for Allen screws size 3 / 4 / 5 / 6 mm,M 5 bits for inner TORX® screws T 10 / 15 / 20 / 25 / 30,Q 1 bit for slotted screws 1,0x5,5 mm,D 1 bit for Phillips recess head screws PH 2,

1 reversible ratchet, 1 bit holder, 1 Cardan joint,1 ea. extension 55 mm, 101,5 mm (swivelling) and 147 mm.


VType 36-part, im plastic case.



36-part 101

51042


JType37-part, in plastic box with bicoloured foam insert.The tools are held safely by the foam insert. Nothingwill be lost.



37-part 201

51043

Set contentsN 10 hexagonal bits size 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,

1 reversible ratchet,1 ea. extension 55 and 100 mm,1 bit holder, 1 Cardan joint,1 adapter 1/4 inch inner square wrench x 1/4 inch Allen,

J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 7 mm,Q 3 bits for slotted screws 4,5 / 6,5 / 8,0 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,C 7 bits for ResisTORX® with borehole T 10 / 15 / 20 / 25 / 27 / 30 / 40.

Set contentsN 11 hexagonal bits size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm, J 7 bits for Allen screws 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm, Q 4 bits for slotted screws 0,5x4 / 0,6x4,5 / 0,8x5,5 / 1,2x6,5 mm, D 2 bits for Phillips recess head screws PH 1/ 2, E 2 bits for Phillips recess head screws PZ 1/ 2, C 6 bits for ResisTORX® with borehole T 10 / 15 / 20 / 25 / 30 / 40,

1 bit reversible ratchet, 1 adapter 25 mm, 1/4 inch J x 1/4 inch z, 1 adapter 50 mm, 1/4 inch J x 1/4 inch z, 1 adapter 75 mm, 1/4 inch J x 1/4 inch N.


PType 14-part, reverse function ring, finely toothed (72teeth), with 2-component handle, in steel box.

51044

Set contentsN 10 hexagonal bits size 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,

1 bit adapter 1/4 inch z x 1/4 inch J,1 ratchet,1 ea. extension 50 and 100 mm.


14-part 201

51044

eng/OP


www.hhw.de51.10

5


PType32-part. With Rastoflex®tk Allraumknarre® finelytoothed (72 teeth) with ring-hand operation. Slidingguide in inner ring (3) and reverse function on outerring (4). Can be locked in 14 angle positions,vertically and horizontally, 7 positions each, bymeans of flex-stop variomatic. In steel box.

51046

Set contents 51046 2011 Rastoflex®tk Allraumknarre®,

N 12 hexagonal bits 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,Q 3 bits for slotted screws 4 / 5,5 / 6,5 mm,D 4 bits for Phillips recess head screws PH 0 / 1 / 2 / 3,J 6 bits for Allen screws, size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 handle with sliding piece, 1 Cardan joint,1 ea. extension 50 mm and 100 mm,1 power tool adapter 1/4inch z x 1/4inch J, length 50 mm, in the Minimus reversible handle,1 bit coupling 1/4 inch x 8 mm with magnetic holder.

Set contents 51047 2011 Rastoflex®tk Allraumknarre®,

N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,C 7 socket wrench bits TORX® with borehole T 10 / 15 / 20 / 25 / 27 / 30 / 40,J 6 bits for Allen screws, size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 handle with sliding piece, 1 Cardan joint,1 ea. extension 50 mm and 100 mm,1 power tool adapter 1/4 inch z x 1/4 inch J, length 50 mm in the Minimus reversible handle,1 bit coupling 1/4 inch x 8 mm with magnetic holder.

Set contents 51046 … 51047 …

32-part 201 201

51047

51046 - 51047


PType32-part, with reversible ratchet, finely toothed (72teeth) with ring-hand operation. Sliding guide ininner ring (1) and reverse function on outer ring (2),in steel box.

Set contents 51050 1011 reversible ratchet,

N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,C 7 socket wrench bits TORX® with hole T 10 / 15 / 20 / 25 / 27 / 30 / 40,J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 handle with sliding piece, 1 Cardan joint, 1 ea. extension 50 mm and 100 mm,1 power tool adapter 1/4 inch z x 1/4 inch J, length 50 mm,1 Minimus reversible handle.

Set contents 51051 1011 reversible ratchet,

N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,Q 3 bits for slotted screws 4 / 5,5 / 6,5 mm,D 4 bits for Phillips recess head screws PH 0 / 1 / 2 / 3,J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 handle with sliding piece, 1 Cardan joint, 1 ea. extension 50 mm and 100 mm,1 power tool adapter 1/4 inch z x 1/4 inch J, length 50 mm,1 Minimus reversible handle.

Set contents 51050 … 51051 …

32-part 101 101

51050 - 51051

51050

51051

ß Hand tools


5


PType33-part, with reversible lever ratchet, steerable, 7 switch steps via flex-stop variomatic, in steel box.

Set contents1 lever reversible ratchet,

N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,C 7 socket wrench bits TORX® with hole T 10 / 15 / 20 / 25 / 27 / 30 / 40,Q 1 bit for slotted screws 5,5 mm,D 1 bit for Phillips recess head screws PH 2,E 1 bit for Phillips recess head screws PZ 2,J 3 bits for Allen screws size 4 / 5 / 6 mm,

1 Cardan joint, 1 magnet detector,1 ea. extension 50 mm and 100 mm,1 Minimus service screwdriver with double blade for

Q Slotted screws 2,5 / 3,5 mm and D Phillips recess head screws PH 0 / 1,

1 bit coupling 1/4 inch with magnetic holder,1 power tool adapter 1/4 inch z x 1/4 inch J, length 50 mm, in the Minimus reversible handle.


33-part 401

51052

51052


PType 32-part, with Readyflex® Freiraumknarre®, reverse function ring, finely toothed (72 teeth), insteel box.

51053

Set contents1 Readyflex® Freiraumknarre®,

N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, C 7 socket wrench bits TORX® with hole TX 10 / 15 / 20 / 25 / 27 / 30 / 40, J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 ea. extension 50 and 100 mm, 1 Cardan joint, 1 handle with sliding piece, 1 power tool adapter 1/4 inch z x 1/4 inch J, length 50 mm, in the Minimus reversible handle, 1 bit coupler 1/4 inch with magnetic holder.


32-part 401

51053

Hexagonal socket set

PType 37-part, reverse function ring, finely toothed (72teeth), with 2-component handle, in steel box. 51054

Set contentsN 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, C 7 socket wrench bits TORX® with hole TX 10 / 15 / 20 / 25 / 27 / 30 / 40, J 6 bits for Allen screws size 3 / 4 / 5 / 6 / 8 / 10 mm,

1 ea. extension 50 und 100 mm, 1 Cardan joint, 1 Ratchet,1 Magnet Detector,1 Minimus service screwdriver with double blade for

Q Slotted Screws 2,5 / 3,5 mm and D Phillips recess head screws PH 0 / 1,

1 Power Tool Adapter 1/4 inch z x 1/4 inch J, length 50 mm, 1 Bit Coupler 1/4 inch x 8 mm mit Magnetaufnahme.


37-part 201

51054

51062

eng/OP

• Bit Rails • Socket Wrench Bits

www.hhw.de51.12

5

Bit rails, magnetic (empty)

NTypeOuter squares for 13 socket wrench bits nominalsize 6,3 (1/4 inch). 2 additional inner squarewrench adapters for ratchets, sliding handles,extension pieces, etc. A strong magnet allows for asecure fastening of the rail to metal objects.Additional boreholes allow the fastening to non-me-tallic objects and walls. The bits are held securely bythe ball by means of turning them 90°. Turning them

90° in the opposite direction will release the bits sothat they can be removed. Tools not included.

51056

for socket wrench bits Length Width Weight 51056 …pcs. mm mm g

13 380 33 350 101

51056

Hexagonal socket wrench bits DIN 3124/ISO 2725

TypeChrome-plated, drop-forged. QualityChrome-vanadium steel.

51059

0With Energy profile.

51061N

51062

With AS-Drive profile.QualityHPQ high-performance steel.

51063VWith Tractions profile.

51059

51061

51063

51059 - 51063


Adjustable wrenches by ATORN:


0 N VSize l d1 51059 … 51061 … 51062 … 51063 …mm approx. mm approx. mm3,5 25 6,0 102

4 25 6,8 103 103 103 403L 4 50 6,7 1044,5 25 7,2 105 105 405

L 4,5 50 7,0 106 1065 25 8,1 107 107 107 407

L 5 50 7,9 1085,5 25 8,6 109 109 109 409

L 5,5 50 8,5 110 6 25 9,2 111 111 111 411

L 6 50 9,2 112 4127 25 10,8 113 113 113 413

L 7 50 11,0 114 114 4148 25 11,7 115 115 115 415

L 8 50 12,0 116 116 4169 25 13,0 117 117 117 417

L 9 50 13,0 118 41810 25 14,3 119 119 119 419

L 10 50 14,5 120 120 42011 25 15,8 121 121 121 421

L 11 50 15,5 122 122 42212 25 17,0 123 123 123 423

L 12 50 17,0 124 124 42413 25 17,9 125 125 125 425

L 13 50 18,0 126 126 42614 25 19,3 127 127 127 427

L 14 50 19,5 128

ß Hand tools


5

Socket wrench bits TRIPLEplus

0Type Mirror finished and chrome polished, drop-forged. Application Multi-purpose use screwing system for hexagonal,double hexagonal, and E-TX screws and nuts. Fitsall standard imperial sizes.


51072

51072

) N A N G 51072 …mm Hexagon Double hexagon Inch E-TX4,0 x x 5/32 E 5 1014,5 x x – E 6 1025,0 x x 3/16 – 1035,5 x x – – 1046,0 x x – E 8 1057,0 x x 9/32 – 1068,0 x x 5/16 E 10 1079,0 x x 11/32 – 108

10,0 x x 3/8 E 12 10911,0 x x 7/16 E 14 11012,0 x x 15/32 E 16 11113,0 x x 1/2 – 11214,0 x x 9/16 E 18 113

Double hexagon socket wrench bits (inch) DIN 3124/ISO 2725

,TypeImperial sizes. High-performance socket wrenchbits, thin-walled, with Dynamic-Drive profile.Nickel-plated and chrome-plated, highly polished.

QualityChromo-Extra. 51073

Size l d1 51073 …inch mm mm3/16 22,2 7,7 1017/32 22,2 8,5 1021/4 22,2 9,3 103

9/32 22,2 10,5 1045/16 22,2 11,5 105

11/32 22,2 12,6 1063/8 22,2 13,8 107

7/16 22,2 15,4 1081/2 22,2 17,5 109

9/16 23,0 18,8 110

51073

Long double hexagon socket wrench bits (inch) ISO 2725-1

,TypeLong, imperial sizes. High-performance socketwrench bits, thin-walled, with Dynamic-Driveprofile. Nickel-plated and chrome-plated, highlypolished.


Size l d1 51079 …inch mm mm3/16 50,6 7,7 1017/32 50,6 8,5 1021/4 50,6 9,3 103

9/32 50,6 10,5 1045/16 50,6 11,5 105

11/32 50,6 12,6 1063/8 50,6 14,1 107

7/16 50,6 15,4 1081/2 50,6 17,5 109

9/16 50,6 18,8 110

51079

eng/OP

• Screwdriver Bits • Socket Wrench Sets • Sets of TORX®

www.hhw.de51.14

5

Screwdriver bits

51074

0TypeSleeves chrome-plated, blades made of specialsteel, burnished.QualityChrome-vanadium steel.

51076

TypeSleeves chrome-plated, blades made of specialsteel, burnished.QualityChrome-alloy steel.

51078 VQuality CVD-TiN-coating for longer service life.

51074 - 51078

0 VBlade thickness x width l1 l2 d 51074 … 51076 … 51078 …mm / size approx. mm approx. mm approx. mmQ 0,6 x 3,5 15 28 12 101 101Q 0,8 x 4,0 15 28 12 102 103 102Q 1,0 x 5,5 15 28 12 103 105 103Q 1,2 x 6,5 15 28 12 104Q 1,2 x 8,0 15 28 12 108 105Q 1,6 x 10,0 15 28 12 106D PH 1 15 28 12 201 201 201D PH 2 15 28 12 202 202 202D PH 3 15 28 12 203 203 203D PH 4 15 28 12 204E PZ 1 15 28 12 301 301E PZ 2 15 28 12 302 302E PZ 3 15 28 12 303 303

51074 102-104 51074 201-303

51076 101-108 51076 201-204

51078 101-106 51078 201-203

51078 301-303

Hexagon screwdriver bits

Type Chrome-plated, drop-forged. Quality Chrome-vanadium steel.

51082

051086N

51088



51082

51086

51088

51090

51082 - 51090

0 N VSize Lenght 51082 … 51086 … 51088 … 51090 …mm mm

3 28 101 102 2013 37 101

L 3 55 1034 28 102 104 2024 37 102

L 4 55 1055 28 103 106 2035 37 103

L 5 55 1076 28 104 108 2046 37 104

L 6 55 1098 28 105 110 2058 37 105

ß Hand tools


5

Hexagonal socket set

0 TypeAll bits are 100 mm long. In sheet steel box withplastic insert.QualityChrome-vanadium steel.


15-part 10161-part 103

51080

Set contents 51080 101JV 7 bits for Allen screws with ball head size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm,M 7 bits for inner Torx® screws TX 10 / 15 / 20 / 25 / 27 / 30 / 40,

1 ball head reversible ratchet with release button.Set contents 51080 103N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,J 7 bits for Allen screws size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm,JV 7 bits for Allen screws with ball head size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm,Q 5 bits for slotted screws 0,4x2,5 / 0,6x3,5 / 0,8x4,5 / 1,0x5,5 / 1,2x7,0 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,M 7 bits for inner Torx® screws TX 10 / 15 / 20 / 25 / 27 / 30 / 40,C 7 bits for inner Torx® screws with borehole TX 10 / 15 / 20 / 25 / 27 / 30 / 40,L 5 bits for Trisquare socket head screws M 3 / 4 / 5 / 6 / 8,

1 T-handle reversible ratchet with release button, 1 ball head reversible ratchet with release button,1 bit holder, 1 handle with sliding piece, 1 bit adapter.

TORX® set

51091

Set contents Satzinhalt4 6 socket wrench bits outer TORX® E 4 / 5 / 6 / 7 / 8 / 10,M 9 socket wrench bits inner TORX® T 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40,

1 reversible ratchet, 1 bit holder with plastic handle, 1 handle with sliding piece,1 ea. extension 54 and 150 mm, 1 Cardan joint.


21-part 101

51091

Type21-part, in sturdy sheet steel box.


Note:TORX® selector see cat.-no. 37930.

VType 20-part, in plastic case.


Note: TORX® selector see cat.-no. 37930.

Set contents4 7 socket wrench bits outer TORX® E 4 / 5 / 6 / 7 / 8 / 10 / 11,

9 socket wrench bits inner TORX® T 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40, 1 T-handle reversible ratchet, 1 swivelling extension 101,5 mm, 1 extension 147 mm, 1 Cardan joint.


20-part 101

TORX® set51092

51092

TORX® set

NType15-part, in plastic case.

QualityVanadium special steel.Note:TORX® selector see cat.-no. 37930.

51097

Set contents4 6 socket wrench bits outer TORX® E 4 / 5 / 6 / 7 / 8 / 10,M 9 socket wrench bits inner TORX® T 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40.


15-part 101

51097

eng/OP

• Screwdriver Bits • Socket Wrench Bits • Reversible Ratchets

www.hhw.de51.16

5

TORX® screwdriver bits

Application For inner TORX® screws.


51093

0Type Chrome-plated. Quality Chrome-vanadium steel.

51094 NType Chrome-plated. Quality Vanadium special steel.


51093

0 N VSize 51093 … 51094 … 51096 …

T8 101 101 1019 102 102 102

10 103 103 10315 104 104 10420 105 105 105

0 N VSize 51093 … 51094 … 51096 …

T25 106 106 10627 107 107 10730 108 108 10840 109 109 109

51094

51096

51093 - 51096

TORX PLUS® screwdriver socket wrench bits

NTypeChrome-plated.ApplicationFor inner TORX® screws. Better torque transmissionthanks to considerably larger contact surface.

QualityVanadium special steel.


51100

51100

Size Length 51100 …IP mm6 30,5 1018 30,5 102

10 30,5 10315 30,5 10420 30,5 105

Size Length 51100 …IP mm25 30,5 10627 30,5 10730 30,5 10840 33,5 109

TORX® socket wrench bits

5110551104

51104 - 51105

TypeChrome-plated.ApplicationFor outer TORX® screws.QualityVanadium steel.


51104

051105V

0 V Size Length 51104 … 51105 …

E approx. mm4 25 101 1015 25 102 1026 25 103 1037 25 104 104

0 V Size length 51104 … 51105 …

E approx. mm8 25 105 105

10 25 106 10611 25 107

ß Hand tools


5

Reversible ratchets DIN 3122/ISO 331551114 - 51120

51114

51116

51117

51120

Readyflex® Freiraumknarre®51123

PType With reverse function ring, finely toothed (72 teeth),steerable, 7 switch steps.

51123

Overall length 51123 …mm137 301

www.atorn.com


Adjustable wrenches by ATORN:


TypeChrome finish and polished. Extremely robustratchet with switch knob for clockwise andcounter-clockwise operation and ergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51114NFinely toothed (72 teeth, ratcheting angle 5°),with ball lock.

51116

Finely toothed (60 teeth, ratcheting angle 6°).Quick reversal thanks to one-hand operation. With 2-component handle.QualityChrome-alloy steel.

51117VFinely toothed (72 teeth, ratcheting angle 5°),for use on screws even in hard-to-reach areas. With thumb rest. One-hand operation: easily turningplastic wheel for reverse operation. More safetythrough larger space between ratchet and screw.Large corner moulding offers more room for preciseoperation.

51120JFinely toothed (72 teeth, ratcheting angle 5°).The thumb rest enables the user to press onto theratchet head without activating the reverse switch.Quick reversal thanks to one-hand operation.

N V JOverall length 51114 … 51116 … 51117 … 51120 …

mm115 201117 201118 201129 101

eng/OP

• Reversible Ratchets • Socket Accessories

www.hhw.de51.18

5

Reversible ratchets DIN 3122/ISO 3315

TypeChrome-plated, extremely robust ratchets withclockwise and counterclockwise operation andergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51126 201

0With reverse lever and quick-release push button.

51127 101

0With reverse lever and quick-release push button.Finely toothed (72 teeth, ratcheting angle 5°).

51129 101NWith reverse lever, locking mechanism in centreposition and ball lock. Oval head. 24 teeth, ratche-ting angle 15°.

51129 102NTypeWith reverse lever, quick-release push button andball lock. Finely toothed, 40 teeth, ratcheting angle9°. Non-slip 2-component handle with attachmenteye.

51130 201

With reverse lever, 22 teeth. With 2-componenthandle.QualityChrome-alloy steel.

51130 202-204

With reverse lever, QuickRelease safety lock and2-component handle, 22 teeth. Quality Chrome-alloy steel.

51132 101VWith reverse lever.

51132 102VWith reverse lever,safety lock and quick-release push button, 20 teeth.

51133 101,With reverse lever. 30 teeth, ratcheting angle 12°.With unlocking mechanism for the ball latchingmechanism. Nickel-plated, highly polished. With 2-component handle.

51125 100ZWith reverse lever and quick-release push button.

51126

51127 101

51129 101

51129 102

51130 201

51130 202

51130 204

51132 101

51132 102

51125 100

51125 - 51133

T-handle reversible ratchet

VType With quickly releasable safety lock.

Application This tool combines the advantages of a T-handlesocket wrench with those of a reversible ratchet.Both powerful and sensitive operation are possible.

51134


51134

51133 101

0 0 N V , ZGesamtlänge 51126 … 51127 … 51129 … 51130 … 51132 … 51133 … 51125 …

mm115 101 101115 102117 201117 202127 101129 102130 101145 201 100153 204

51129 102

ß Hand tools


5

Readyflex® Freiraumknarre®

PTypeChrome-plated, with reverse lever and flexiblelever arm. Joint can be arrested in 7 positions bymeans of flex-stop variomatic.

ApplicationThis ratchet combines all the advantages of aratchet with a flexible lever arm with those of aratchet with a rigid lever arm. It guarantees fullleverage, especially in angled positions. It istherefore suitable for application in hard-to-reachareas.QualityChrome-vanadium steel.

51135

51135


Zyklop ratchet

sTypeFlywheel design and non-slip quick-action sleeve forhigh working speed. Swivelling ratchet head. Presetpositions at 0°, 75°, and 90° in both directions.Usable as a standard screwdriver when in the

0° position. Quick-release push button, clockwiseand counterclockwise operation, finely toothed,small ratcheting angle of 5° - 6°. Multi-componentKraftform handle for effortless work.

51136

The ratchet head swivelsfreely and can be unlockedin any position by slidingthe switch which is locatedon both sides.

The flywheel designaccelerates thescrewing.

The socket locking mechanism accelerates mountingand removing of the sockets and extensions. The balllock secures the sockets and the accessories andalso provides additional safety during the application.Simply press the release button and tool exchange ispossible in any defined position.

The Zyklop ratchet is quickly and easily reversible inany position by means of the knurl.


51136

Socket accessories

TypeChrome-plated, drop-forged.QualityChrome-vanadium steel.

51140

051140 203ßFlexible bit holderWith flexible shank, large socket depth. Shaft standsa torque value of 12 Nm in both directions. Shaftlength 100 mm.

51143

51143 102

HolderWith 2-component handle.QualityChrome-alloy steel.

51145

With QuickRelease safety lock.QualityChrome-alloy steel.

51144V

51140 - 51145

51140 201

51140 202

51144 104

51140 203

51140 204

51143 102

51143 106

51143 107

51144 105 51145 104

51145 101

0 V51140 … 51143 … 51145 … 51144 …

Handle with sliding piece 201 101 101Bit holder 202 102

Flexible bit holder 203Cardan joint 204 104 104 104

Adapter 1/4 inch . x 3/8 inch z 205 105 105Adapter 1/4 inch . x 1/2 inch z 106

FixGRIP adapter 1/4 inch . x 3/8 inch z 107

eng/OP

• Extensions • Socket Wrench Sets

www.hhw.de51.20

5

Extension pieces


51153

051156N

51157


51157 105

Flexible extensionLoad capacity 5 Nm. Only for clockwise operation.

51159V

51162J

51164

With QuickRelease safety lock.Quality Chrome-alloy steel.

51153 - 51164

51153 103

51157 105

51159 105

51159 100

51162 104

51164 101

Extension pieces with locking mechanism

JTypeChrome-plated, polished.ApplicationThe locking mechanism prevents the unintentionaldrop-off of the socket wrenches.QualityVanadium steel.

51165

Length 51165 …mm100 201250 203

51165

Swivelling extensions

VTypeChrome-plated, polished.ApplicationWith ball-type, conical outer square. Allows a flexangle to any direction of 8°.


51168 101

Length 51168 …mm25,0 101

101,5 102

51168 102

51168

Cardan extensions

NTypeWith ball lock.ApplicationThe extension allows a turning of 15°.

51167

Length 51167 …mm

55 10197 102

148 103

51167

Adjustable extension

ApplicationBy pulling down the locking sleeve, the inner partcan be pulled out (6-x length adjustment). 2 step system:The first step is used for secure hold of the socketwrench bits in a straight position.The second step (achieved by pulling the socketwrench bit forward) uses the built-in Cardan functionfor a flex angle of up to 15°.

The tool can also be used as an extendablescrewdriver.QualityChrome-vanadium steel.

51169

Length adjustment 51169 …approx. mm

190 - 310 101

51169

0 N V JLength 51153 … 51156 … 51157 … 51159 … 51162 … 51164 …

mm25 10055 101 201 101 101 101

100 102 102 102150 103 202 103 102 102250 104356 103402 105152 105

ß Hand tools


5


0 Type22-part, in sheet steel box with foam insert. All toolsare stored vibration-free.QualityChrome-vanadium steel.

51173

Set contentsN 17 hexagonal bits with Energy profile, size 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 /

21 / 22 mm,1 ea. reversible ratchet, Cardan joint, 1 ea. extension 50, 75 and 150 mm.


22-part 101

51173


VType 46-part, in plastic box.


51175Set contentsx N 12 hexagonal bits size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm,

J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm, Q 4 bits for slotted screws 0,5 x 4 / 0,6 x 4,5 / 0,8 x 5,5 / 1,0 x 6 mm, D 2 bits for Phillips recess head screws PH 1 / 2, E 2 bits for Phillips recess head screws PZ 1 / 2,

1 adapter 1/4 inch square (hollow) x 1/4 inch hexagonal (hollow), 1 reversible ratchet, 1 bit holder with plastic handle, 1 Cardan joint, 1 extension 101,5 mm.

w N 12 hexagonal bits size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 mm, 1 adapter 3/8 inch square (hollow) x 1/4 inch hexagonal (hollow), 1 reversible ratchet, 1 Cardan joint, 1 extension 150 mm.


46-part 201

51175


NType17-part, with tempered hexagonal socket wrenchbits, in sheet steel case.


Set contentsN 12 hexagonal bits size 6 / 7 / 8 / 9 / 10 / 11 / 13 / 14 / 15 /16 / 17 / 19 mm,

1 reversible lever ratchet, 1 handle with sliding piece, 1 Cardan joint, 1 ea. extension 125 and 250 mm.


17-part 101

51178


Type19-part, chrome-plated, in sheet steel box.

QualityChrome-alloy steel. 51180

Set contentsN 14 bits with AS-Drive profile size 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 mm,

1 reversible ratchet, 1 handle with sliding piece,1 ea. extension 76 and 240 mm, 1 Cardan joint.


19-part 102

51180

5

eng/OP






16-part 101

51181

Set contentsN 11 hexagonal bits size 8 / 10 / 11 / 12 / 13 / 14 / 15 / 17 / 19 / 21 / 22 mm,

1 reversible ratchet, 1 handle with sliding piece,1 Cardan joint, 1 ea. extension 127 and 254 mm.


NType17-part, in sheet steel case.



17-part 101

51184


Type Chrome-plated, in sheet steel box. Quality Chrome-alloy steel.

51185 105TypeIn TCS inserts.

51185

Set contents 51185 101A 11 bit double hexagonal with AS-Drive profile size 8 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 mm,

1 reversible ratchet, 1 ea. extension 76 and 240 mm 1 Cardan joint.

51185 101

51185 105Set contents 51185 105A 14 double hexagonal bits with AS-Drive profile size 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 /

21 / 22 mm, 1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 76 and 240 mm 1 Cardan joint.


15-part 10119-part 105


Type19-part, in plastic case. With Quick-Releasesystem (one-hand safety lock).

QualityChrome-alloy steel. 51188


19-part 101

51188

Set contentsA 14 socket wrench bits size 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 mm,

1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 ea. extension 76 and 240 mm.

www.hhw.de51.22

Set contentsA 12 double hexagonal bits with UD profile size 6 / 7 / 8 / 9 / 10 / 11 / 13 / 14 / 15 / 16 / 17 / 19 mm,

1 reversible ratchet, 1 handle with sliding piece,1 Cardan joint, 1 ea. extension 125 and 250 mm.

5

ß Handwerkzeuge

eng/OP




51186

51186


25-part 202



Set contentsN 16 hexagonal bits, size 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 /18 / 19 / 21 / 22 mm,Q 3 bits for slotted screws 1,0 x 5,5 / 1,2 x 8,0 / 1,6 x 10,0 mm,D 3 bits for Phillips recess head screws PH 1 / 2 / 3,J 4 bits for Allen screws size 4 / 5 / 6 / 8 mm,

1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 ea. extension 75, 127 and 254 mm.

51187


32-part 101


Set of hexagonal and double hexagonal socket wrenches

VType58-part, in sheet steel case.


Set contentsN 3 hexagonal bits, size 6 / 7 / 8 mm,A 14 double hexagonal bits, size 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 mm,A 14 double hexagonal bits, long, size 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 mm,Q 3 bits for slotted screws 1,0 x 5,5 / 1,2 x 8,0 / 1,6 x 10,0 mm,D 3 bits for Phillips recess head screws PH 2 / 3 / 4,J 9 bits for Allen screws size 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 12 mm,

1 ea. reversible ratchet, handle with joint, bit holder, handle with sliding piece, Cardan joint, crank,1 ea. extension 74, 150, 202 and 304 mm, 1 flexible extension 210 mm,1 adapter 1/4inch z x 3/8 inch . .


58-part 101

51189


Solid carbide milling cutters by ATORN:

ATORN‘s high-quality milling tools.

www.hhw.de 51.23

Satzinhalt11 bits double hexagonal with AS-Drive profile size 8 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 mm,

A 1 ea. double hexagonal bit with AS-Drive profile size 20,8 mm-13/16 inch and 16 mm - 5/8 inchwith rubber insert for spark plugs,

J 7 bits for Allen screws size 3 / 4 / 5 / 6 / 7 / 8 / 10 mm,1 reversible ratchet,

1 handle with sliding piece, 1 ea. extension 76 and 240 mm1 Cardan joint.

eng/OP

• CDX-Super • Bit Rails • Socket Wrench Bits

www.hhw.de51.24

5

High-performance socket wrench systems CDX-SuperJThe high-performance drive system with 4 advantages- As compact as 3/8 inch, powerful as

1/2 inch, load capacity 500 Nm- Safety and reliability in difficult working

conditions- Fully compatible with 3/8 inch, all drive

elements with 3/8 inch square end can betaken on

- Safety lock and quick release. Socket wrenchbits and extensions can not drop off.

��

��Nm

ISO

ISO

FACOM

FACOM3/8"

381/2"

3/8"

SuperCDX-


21-part Reversible ratchet, Cardan joint, 1 ea. extension 125 and 250 mm, 203A 17 socket wrench bits size 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 /

21 / 22 / 24 / 26 / 27 mm.

Set of double hexagonal socket wrenches CDX-Super51200

JTypeChrome finish and polished. Drive 3/8 inch CDX-Super with OGV® profile. In box.

51200

Socket accessories and combination elements CDX-Super

JTypeChrome finish and polished. Drive 3/8inch CDX-Su-per.

51210 201Reversible ratchet72 teeth, with Vollhand system, compact head,ratcheting angle 5°, tightening torque 500 Nm.

51210 202-203Extension piecesWith locking device.

51210 204Cardan jointSpring brake, remains in selected position.

51210 205AdapterInner square drive 3/8 inch, outer square 1/2 inch.

51210 207Bit holderFor use with 1/4 inch bits.

Length 51210 …mm

Reversible ratchet – 210 201Extension – 125 202Extension – 250 203

cardan joint – 67 204Adapter 3/8inch - 1/2 inch 35 205

Bit holder 3/8inch - 1/4 inch bit 30 207

51210 201

51210 202-203

51210 204 51210 205 51210 207

��

��

51210

ß Hand tools


5

Hexagonal socket wrench bits CDX-Super

JTypeChrome finish and polished. Drive 3/8 inch CDX-Super, with OGV® profile for powerful tighteningand long service life. Thanks to the special design ofthe OGV® profile, the bits do not caulk the screw.

51213

51213

Size l d1 51213 …mm mm approx. mm

10 27,0 18,6 20411 27,0 18,6 20512 27,0 18,6 20613 30,0 18,5 20714 30,0 18,6 20815 30,0 19,0 20916 30,0 20,0 21017 30,0 21,8 211

Size l d1 51213 …mm mm approx. mm

18 33,0 21,7 21219 33,0 23,0 21320 33,0 22,2 21421 33,0 23,5 21522 33,0 23,7 21623 33,0 26,0 21724 33,0 26,5 218


NTypeOuter squares for 14 socket wrench bits nominalsize 10 (3/8inch). 2 additional inner square wrenchadapters for ratchets, sliding handles, extensionpieces, etc. A strong magnet allows for a securefastening of the rail to metal objects. Additionalboreholes allow the fastening to non-metallic objectsand walls. The bits are held securely by the ball bymeans of turning them 90°. Turning them 90° in theopposite direction will release the bits so that theycan be removed. Tools not included.

51218

for socket wrench bits Length Width Weight 51218 …pcs. mm mm g

14 480 33 450 101

51218



51222


51223N

51224

With AS-Drive profile.QualityChrome-alloy steel.


51223

0 N VSize l d1 51222 … 51223 … 51224 … 51226 …mm approx. mm approx. mm

6 26 9,7 101 201 3017 26 10,5 102 202 3028 26 12,0 103 203 203 3039 26 13,2 104 204 304

10 27 14,5 105 205 205 30511 27 15,8 106 206 206 30612 28 17,0 107 207 207 30713 29 18,3 108 208 208 30814 29 19,5 109 209 209 30915 30 20,8 110 210 210 31016 30 22,0 111 211 211 31117 30 23,3 112 212 212 31218 31 24,5 113 213 213 31319 31 26,0 114 214 214 31420 32 27,0 115 31521 32 28,5 116 216 31622 33 29,5 117 217 217 317

51224 5122651222

51222 - 51226

eng/OP

• Socket Wrench Bits • Screwdriver Bits

www.hhw.de51.26

5

Double hexagon socket wrench bits DIN 3124/ISO 2725


51229NWith UD profile.


51229

N VSize l d1 51229 … 51232 …mm approx. mm approx. mm

6 28 9,7 0987 28 11,0 0998 28 12,1 1009 24 13,0 101 101

10 25 14,5 102 10211 27 16,0 103 10312 27 17,0 104 10413 28 18,5 105 10514 28 19,5 106 106

N VSize l d1 51229 … 51232 …mm approx. mm approx. mm

15 29 21,0 107 10716 29 28,0 108 10817 30 23,5 109 10918 30 24,5 110 11019 31 26,5 111 11120 31 27,0 11221 31 28,5 11322 32 29,5 114 114

51232

51229 - 51232

Long double hexagon socket wrench bits

51234 51235

51234 - 51235

Multi-purpose socket wrench bit -Gripper-

TypeReplaces all hexagonal bits of sizes 7 through 19mm. 54 steel pins fit automatically on each nut orscrew head. Special round-pin design protectsscrew heads against damage. Each pin has aresilience with a strong back stop for optimum gripof screw or nut.

ApplicationThis multi-purpose tool allows safe grip of manyforms, like three-square, square end, hexagonalend, TORX® profiles, wing nuts, hook- and ringscrews as well as other screws and nuts withpolygon and inch sizes.QualityHousing made of alloyed steel.

51238

51238

Length Ø 51238 …mm mm53,5 25,4 401

Application For deeply set screws and protruding bolts.

Note: Cat.-no. 51235 213 with rubber insert for sparkplugs. Cat.-no. 51235 214-215 are in compliancewith DIN 3124/ISO 2725.

51234

Type Chrome-plated, with AS-Drive profile.Quality HPQ high-performance steel.

51235 VType Chrome-plated, drop-forged and polished. WithTractions profile.Quality Chrome-vanadium steel.

VSize l d1 51234 … 51235 …mm approx. mm approx. mm

10 54 14,4 202 20211 54 15,7 203 20312 54 17,0 204 20413 54 18,3 205 20514 57 19,5 206 20615 60 20.6 20716 60 21,8 208 208

VSize l d1 51234 … 51235 …mm approx. mm approx. mm

17 62 23,0 209 20918 65 24,3 210 21019 65 25,5 211 21120 68 26,6 212

20,8 70 27,4 21321 68 28,0 21422 68 29,4 215

ß Hand tools


5

Joint hexagonal socket wrench bits

VTypeShort, chrome-plated. With Tractions profile.ApplicationFor hard-to-reach areas.


Note:Also available as set. Please send us your enquiry!

51241

51241

d1

d2

l

f

Size l d1 d2 f 51241 …mm mm mm mm mm

10 43 13,8 19 6,8 20111 43 15,0 19 6,8 20212 44 16,6 19 7,3 20313 44 17,8 19 7,3 20414 45 19,0 19 9,3 205

Size l d1 d2 f 51241 …mm mm mm mm mm

15 45 20,4 19 9,3 20616 46 22,0 19 9,2 20717 46 22,8 19 9,2 20818 47 24,5 19 10,2 20919 48 25,2 19 11,2 210

Double hexagonal socket wrench bits (inch) ISO 2725-151236

,TypeImperial sizes. High-performance socket wrenchbits, thin-walled, with Dynamic-Drive profile.Nickel-plated and chrome-plated, highly polished.


Size l d1 51236 …inch mm mm

1/4 25,8 10,0 1015/16 25,8 11,4 1023/8 25,8 14,3 103

7/16 25,8 15,7 1041/2 25,8 18,0 105

17/32 25,8 18,8 1069/16 27,4 19,6 107


19/32 27,8 20,4 1085/8 28,3 21,1 109

11/16 28,8 23,6 1103/4 30,2 25,1 111

13/16 31,3 26,7 1127/8 32,5 29,1 113

Long double hexagonal socket wrench bits (inch) ISO 2725-151237

,Typelong, imperial sizes. High-performance socketwrench bits, thin-walled, with Dynamic-Driveprofile. Nickel-plated and chrome-plated, highlypolished.



1/4 56 10,0 1015/16 56 11,4 1023/8 56 14,3 104

7/16 56 15,7 1051/2 60 18,0 106

9/16 60 19,6 107


19/32 60 20,4 1085/8 60 21,1 109

11/16 60 23,6 1103/4 60 25,2 111

13/16 60 26,7 1127/8 60 29,1 113

Screwdriver bits

NTypeSleeves chrome-plated, blades made of specialsteel, burnished. Square drive C10 DIN 3120, ISO1174. With ball-retaining groove.

QualityVanadium special steel.

QBlade thickness x width l1 l2 d 51244 …

mm mm mm mm1,0 x 5,5 27 55 17,5 2011,2 x 8,0 27 55 17,5 202

1,6 x 10,0 23 55 17,5 203

DSize l1 l2 d 51244 …

mm mm mmPH 1 27 55 17,5 301PH 2 23 55 17,5 302PH 3 23 55 17,5 303

51244 201-203

51244 301-303

51244

eng/OP

• Screwdriver Bits • Set of TORX® • Socket Wrench Bits

www.hhw.de51.28

5

Hexagon screwdriver bits DIN 3120/ISO 117451246 - 51250

TypeChrome-plated.QualityChrome-vanadium special steel.

51246

0With ball-retaining groove and lateral borehole.

51247NWith ball-retaining groove.

51248

Chrome-alloy steel.

51250V

51246 51247

51248 51250

Long hexagon ball head screwdriver bits51254

NTypeChrome-plated, with ball-retaining groove. Allows fora flex angle of approx. 15 - 20°.

QualityChrome-vanadium special steel, burnished. 51254

51254 105

Size l d 51254 …mm mm mm4 L 132 17,5 1005 L 132 17,5 1016 L 132 17,5 1028 L 134 17,5 104

10 L 134 19,0 105

Hexagon ball head screwdriver bits51253

VTypeSleeves chrome-plated, blades steel-grey. Allows aflex angle of 20°.

QualitySleeves made of chrome-vanadium steel. 51253

Size l d 51253 …mm mm mm

5 116 17 2016 116 17 2027 116 17 2038 116 19 204

10 116 19 205

Hexagon screwdriver bits (inch)

VTypeSleeves chrome-plated, blades steel-grey.

QualitySleeves made of chrome-vanadium steel.

51256

51256

Size l d 51256 …inch mm mm

1/8 50 17 3015/32 55 17 3023/16 60 17 3037/32 65 17 3041/4 70 19 305

5/16 75 19 3063/8 80 19 307

0 N VSize l d 51246 … 51247 … 51248 … 51250 …mm approx. mm approx. mm

3 52 17,5 101 101 3014 52 17,5 102 202 102 3025 52 17,5 103 203 103 3036 52 17,5 104 204 104 3047 52 18,0 105 105 3058 52 18,0 106 206 106 3069 52 19,0 107 307

10 52 19,0 108 208 108 30812 52 19,0 109 309

ß Hand tools


5

TORX® set51257

NType15-part, in plastic case.QualityVanadium special steel.

Note:TORX® selector see cat.-no. 37930. 51257

Set contents4 8 socket wrench bits outer TORX® E 5 / 6 / 7 / 8 / 10 / 11 / 12 / 14,M 7 socket wrench bits inner TORX® T 20 / 25 / 27 / 30 / 40 / 45 / 50.


15-part 101

TORX® screwdriver bits 51258 - 51261

TypeChrome-plated.ApplicationFor inner TORX® screws.


51258

0

51259NVanadium special steel.

51261VSleeve chrome-vanadium steel.

51258 51259 51261


TypeChrome-plated.ApplicationFor outer TORX® screws.Note:TORX® selector see cat.-no. 37930.

51264

0Chrome-vanadium steel.

51262NVanadium special steel.

51263VChrome-vanadium steel.

51262 - 51264

51262 5126351264

Allen XZN screwdriver bits

VTypeSleeves chrome-plated, blades steel-grey.

ApplicationFor trisquare socket head screws (XZN).QualitySleeves made of chrome-vanadium steel.

51265

Size Length 51265 …M mm5 40 2016 40 2028 41 203

Size Length 51265 …M mm

L 8 88 20410 42 205

L 10 89 206

51265

0 N VSize Length 51264 … 51262 … 51263 …

E approx. mm5 28 101 401 2016 28 102 402 2027 28 103 403 2038 28 104 404 204

0 N VSize Length 51264 … 51262 … 51263 …

E approx. mm10 28 105 405 20511 28 106 406 20612 28 107 407 20714 28 108 408 208

0 N VSize Length 51258 … 51259 … 51261 …

T approx. mm15 43,5 10120 43,5 10220 47,0 10120 49,0 20125 43,5 10325 47,0 10225 49,0 20227 43,5 10427 47,0 10327 49,0 20330 43,5 105

0 NVSize Length 51258 … 51259 … 51261 …

T approx. mm30 47,0 10430 49,0 20440 43,5 10640 47,0 10540 49,0 20545 43,5 10745 47,0 10645 49,0 20650 44,5 10850 47,0 10750 49,0 207

eng/OP

• Reversible Ratchets

www.hhw.de51.30

5


51275

51276

51277

51279

51275 - 51279

Readyflex® Freiraumknarre®51281

PTypeWith reverse function ring, finely toothed (72 teeth), 7 switch steps, chrome-plated. Lockable by meansof yellow Flex button. Extremely robust ratchet,turning the head reverses direction from clockwiseto counter-clockwise and vice versa. With ergonomi-cally-shaped handle made of plastics. With flexiblelever arm, joint can be arrested in any angleposition.The sliding guide in inner ring (1) enablesthe user to press onto the ratchet head withoutactivating the reverse switch. Reverse function bymeans of one-hand operation on outer ring (2).

ApplicationThis ratchet combines all the advantages of aratchet with a flexible lever arm with those of aratchet with a rigid lever arm. It guarantees fullleverage, especially in angled positions. It istherefore suitable for application in hard-to-reachareas.QualityChrome-vanadium steel.

51281


Reversible ratchets51282

TypeFinely toothed (60 teeth). Handle may be raised orlowered by approx. 90°. Lockable in followingpositions: straight, 30° up, 60° up, 30° down.Unlocked by depressing button in handle, DBGM.QualityChrome-alloy steel.

51282



mm175 101185 101194 101200 101

TypeChrome-plated, extremely robust ratchet withswitch knob for clockwise and counter-clockwi-se operation and ergonomically-shaped handlemade of plastics.QualityChrome-vanadium steel.

51275NTypeGround, with ball lock and finely toothed (72 teeth,ratcheting angle 5°).

51276

TypeFinely toothed (60 teeth, ratcheting angle 6°).For application in hard-to-reach areas. With 2-com-ponent handle.QualityChrome-alloy steel.

51277VTypeFinely toothed (72 teeth, ratcheting angle 5°),for use on screws even in hard-to-reach areas.With thumb rest. One-hand operation: easily turningplastic wheel for reverse operation. More safetythrough larger space between ratchet and screw.Large corner moulding offers more Room for preciseoperation.

51279JTypeFinely toothed (72 teeth, ratcheting angle 5°).The thumb rest enables the user to press onto theratchet head without activating the reverse switch.Quick reversal thanks to one-hand operation.

ß Hand tools


5


51284 102

51285 101

51285 102

51286 101

51287 101

51287 102

51283 - 51287

Reversible ratchets with turning handle

51289 101,TypeDIN 3120/ISO 1174. Nickel-plated and chrome-pla-ted, highly polished. Smooth running one-handreverse ring on the handle for reversal of operationby a simple, short turn. Integrated quick-turning discon the square section for easier tightening andloosening of screw connections. Unlocking device ofball catch for effortless and quick push-buttonexchange of socket wrench bits. Fine-pitched teeth(72 teeth), ratcheting angle 5°. 2-component plastichandle with attachment eye.QualityVanadium-extra.

51289 201JTypeDIN 3122/ISO 3315. Calendered and chrome-pla-ted. Ratcheting angle = 0° with rotatable handle.Ratcheting angle = 6° for standard usage (finelytoothed 60 teeth). Simple unlocking of the tools bypushing a button even with oily hands or gloves.Er-gonomically shaped ratchet head. Heel of the handcan be used to prevent sliding off and to supportscrewing.

51289 101

51289 201

, JOverall length 51289 … 51289 …

mm215 101235 201

51289

51283 100

TypeChrome-plated, extremely robust ratchet withclockwise and counterclockwise operation andergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51286 101

0With reverse lever and quick-release push button.

51284 102NWith reverse lever and quick-release push button,tear-shaped head for better access, non-slip 2-component handle with attachment eye. Finelytoothed (60 teeth).

51285 101

With reverse lever, 30 teeth.QualityChrome-alloy steel.

51285 102

Type With reverse lever, QuickRelease safety lock and2-component handle, 30 teeth. Quality Chrome-alloy steel.

51287 101VWith reverse lever, polished, 30 teeth.

51287 102VWith reverse lever, polished, 30 teeth. Additionallywith safety lock and quick-release push button.

51283 100ZWith reverse lever.

0 N V ZOverall length 51286 … 51284 … 51285 … 51287 … 51283 …

mm190 101193 101193 102200 101200 102 102 100

eng/OP

• Reversible Ratchets • Socket Accessories • Extensions • Ring Wrenches

www.hhw.de51.32

5

Reversible ratchets

VTypeWith reverse lever.Chrome finish and polished.Extremely robust ratchet with clockwise and

counter-clockwise operation, swivelling head andergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51290


51290

Zyklop ratchet

sTypeFlywheel design and non-slip quick-action sleeve forhigh working speed. Swivelling ratchet head. Presetpositions at

Preset positions at 0°, 75°, and 90° in bothdirections.Usable as a standard screwdriver when in the 0° position. Quick-release push button,clockwise and counterclockwise operation, finelytoothed, small ratcheting angle of 5° - 6°. Multi-component Kraftform handle for effortless work.

51294



The locking mechanism accelerates mounting andremoving of the socket wrench bits and extensions.The ball lock secures the socket wrench bits and theaccessories and also provides additional safetyduring the application. Simply press the releasebutton and tool exchange is possible in any definedposition.



51294

Socket accessories

51300 201

0 N V51299 … 51300 … 51301 … 51302 … 51303 … 51304 …

Handle with sliding piece 101 201 101 101Bit holder 102

Crank 202Cardan joint 103 203 103 103 103

Adapter 3/8inch . x 1/4inch z 104 204 104 204Adapter 3/8inch . x 1/2inch z 105 205 105 205

FixGRIP adapter 3/8inch . x 1/2inch z 106

51300 202

51300 20351299 104 51299 105 51301 106

51304 102

51302 101

51302 103

51299 - 51304


51299

051300N

51300 202NCrankWith rotating handle.

51301


51302

With QuickRelease safety lock.QualityChrome-alloy steel.

51303V

51304

ß Hand tools


5

Extension pieces51308 - 51314

TypeChrome-plated, drop-forged.

51308

0QualityChrome-vanadium steel.

51309NQualityVanadium 31CrV3.

51310


51312VQualityChrome-vanadium steel.

51312 201VFlexible extensionBurnished shaft.

51314


51310 102

51314 101

51308 104

51312 104

51312 201

51309 103

Swivelling extensions

VTypeChrome-plated, polished.ApplicationWith ball-type, conical outer square. Allows a flexangle to any direction of 8°.


51315

51315 201 51315 202

51315 203

Overall length 51315 …mm

36 20174 202

254 203

Cardan extensions

NTypewith ball lock.ApplicationThe extension allows a turning of 15°.

51316

51316

Length 51316 …mm

76 101125 102250 103

Extendable extension

ApplicationBy pulling down the locking sleeve, the inner partcan be pulled out (7-x length adjustment). 2 step system: The first step is used for secure hold of the socketwrench bits in a straight position.The second step (achieved by pulling the socket

wrench bit forward) uses the built-in Cardan functionfor a flex angle of up to 15°.The tool can also be used as an extendablescrewdriver.


51317Length adjustment 51317 …approx. mm

235 - 385 101

51317

Open double hexagonal ring wrenches (crowfoot wrenches)

VType Chrome-plated, with inside square drive.

Application Especially for working in hard-to-reach places.


51318

51318

Size 51318 …mm

16 10117 10218 10319 104

Size 51318 …mm

21 10522 10624 10727 109

0 N VLength 51308 … 51309 … 51310 … 51312 … 51314 …

mm36 10150 10075 101 101 102 102 101

125 103 102 103 103150 104 104160 102180 110202 105210 201240 105 103250 105 103 106304 107508 108711 109

eng/OP


www.hhw.de51.34

5



QualityVanadium 31CrV3.

51328

Set contentsN 14 hexagonal bits, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 19 / 22 / 24 / 27 / 30 / 32 mm,

1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint,1 ea. extension 125 and 250 mm.


19-part 101

51328




Set contentsN 14 hexagonal bits with Energy profile, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 19 / 22 / 24 / 27 / 30 /

32 mm,1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint, 1 ea. extension 125 and 250 mm.


19-part 101




Set contentsN 15 hexagonal bits with Energy profile, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 22 / 24 / 27 /

30 /32 mm,N 2 hexagonal bits with Energy profile for spark plugs, size 16 / 21 mm,

1 reversible ratchet, 1 Cardan joint, 1 adapter 1/2 inch x 3/8 inch,1 ea. extension 125 and 250 mm.


22-part 101


NType25-part, in sheet steel case. Double hexagonalwith UD profile.


Set contents19 double hexagonal bits, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 23 / 24 / 26 / 27 /

28 / 30 / 32 mm,1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint, 1 crank 395 mm,1 ea. extension 125 and 250 mm.


25-part 101

51332

51332

ß Hand tools


5


NTypeCombination set mm/inch, 31-part, in sheet steelcase.


Set contentsA 10 double hexagonal bits with UD profile, size 11 / 13 / 14 / 17 / 19 / 22 / 24 / 27 / 30 / 32 mm,A 16 double hexagonal bits with UD profile, 3/8 / 13/32 / 7/16 / 1/2 / 9/16 / 19/32 / 5/8 / 11/16 / 3/4 / 25/32 /

13/16 / 7/8 / 15/16 / 1 / 1.1/16 / 1.1/8,1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint,1 ea. extension 125 and 250 mm.


31-part 101

51335

Set of hexagon socket wrenches

Type23-part, in plastic case. With Quick-Releasesystem (one-hand safety lock).

Quality Chrome-alloy steel. 51341


23-part 101

51341

Set contentsN 17 socket wrench bits with AS-Drive profile size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 /

24 / 27 / 30 / 32 / 34 mm,1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint, 1 ea. extension 75, 130 and 255 mm.

Sets of hexagon and double hexagon socket wrenches

Type Chrome-plated, in sheet steel box.


51336 106TypeIn TCS inserts.

51336 103 51336 106 51336 108

51337 103 51337 106 51337 108

Hexagon double hexagonSet contents 51336 … 51337 …

16-part 103 10323-part 106 10629-part 108 108

51336 - 51337

Set contents 51336 106 + 51337 10617 bits with AS-Drive profile size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 /

21 / 22 / 24 / 27 / 30 / 32 / 34 mm,1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 75, 130 and 255 mm, 1 Cardan joint.


18 / 19 / 20 / 21 / 22 / 23 / 24 / 26 / 27 / 28 /30 / 32 / 34 mm,

1 reversible ratchet, 1 handle with sliding piece,1 ea. extension 75, 130 and 255 mm, 1 Cardan joint.


30 / 32 / 34 / mm,1 reversible ratchet, 1 ea. extension 130 and 255 mm.

eng/OP


www.hhw.de51.36

5




51339


25-part 101 101

51338 - 51339


JType 21-part, with safety lock, in plastic box.


Set contentsN 17 hexagonal bits with OGV® profile, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 23 / 24 /

27 / 30 / 32 mm, 1 reversible ratchet, 1 Cardan joint, 1 ea. extension 125 and 250 mm.


21-part 201

Set of hexagonal socket wrenches 51345

JType21-part, in plastic box.


Set contentsN 17 hexagonal bits with OGV® profile, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 23 / 24 /

27 / 30 / 32 mm,1 reversible ratchet, 1 Cardan joint, 1 ea. extension 125 and 250 mm.

51345


21-part 101




Set contents SatzinhaltN 18 hexagonal bits with Energy profile, size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 /

23 / 24 / 27 / 30 / 32 mm,J 5 bits for Allen screws, size 7 / 8 / 10 / 12 / 14 mm,D 2 bits for Phillips recess head screws PH 3 / 4,M 5 bits for inner TORX® screws, screws, T 30 / 40 / 45 / 55 / 60,

1 reversible ratchet, 1 Cardan joint, 1 ea. extension 125 and 250 mm.


34-part 101

Set contents20 socket wrench bits size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 / 26 / 27 /

28 / 30 / 32 mm,1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint,1 ea. extension 125 and 248 mm.

ß Hand tools


5




51349

51349

Set contents Satzinhaltx

N 5 hexagonal bits with Energy profile, size 5,5 / 7 / 8 / 10 / 13 mm,J 3 bits for Allen screws, size 3 / 4 / 5 mm,

1 ea. reversible ratchet, handle with sliding piece, Cardan joint,1 ea. extension 50 and 105 mm,

v

N 11 hexagonal bits with Energy profile, size 10 / 13 / 16 / 17 / 18 / 19 / 22 / 24 / 27 / 30 / 32 mm,J 6 bits for Allen screws, size 6 / 8 / 10 / 12 / 14 / 17 mm,

1 reversible ratchet, 1 handle with sliding piece, 1 Cardan joint,1 ea. extension 125 and 250 mm.


35-part 201


JType 27-part, in plastic box.


Set contentsx

N 9 hexagonal bits,Size 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 mm, 1 reversible ratchet, 1 extension 100 mm 1 Cardan joint, 1 handle with sliding piece.

v

N 11 hexagonal bits,Size 10 / 11 / 12 / 13 / 14 / 16 / 17 / 19 / 21 / 24 / 27 mm, 1 reversible ratchet, 1 extension 125 mm, 1 Cardan joint.

51350


27-part 201

Set of socket wrenches

Type82-part, in aluminium case, with removable toolinsert.


51357

51357

Set contentsx

N 13 socket wrench bitsSize 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,

J 4 bits for Allen screwsSize 3 / 4 / 5 / 6 mm,

Q 3 bits for slotted screws 4 / 5,5 / 7 mm, D 2 bits for Phillips recess head screws PH 1 / 2, E 2 bits for Phillips recess head screws PZ 1 / 2, M 6 bits for TORX® screws

T 8 / 10 / 15 / 20 / 25 / 30, 1 reversible ratchet, 1 handle with sliding piece, 1 bit holder with plastic handle,1 Cardan joint, 1 flexible extension 150 mm, 1 ea. extension 50 / 100 mm.

vN 18 socket wrench bits

Size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 / 27 / 30 / 32 mm,

N 2 hexagonal bits, long size 16 / 21 mm, 1 reversible ratchet, 1 Cardan joint, 1 ea. extension 125 / 250 mm, 1 adapter 1/2 inch x 8 mm / bit adapter,1 adapter bit ength 30 mm.

N bits with bit mount 8 mm:Q 3 bits for slotted screws 4 / 5,5 / 7 mm, D 2 bits for Phillips recess head screws PH 3 / 4, E 2 bits for Phillips recess head screws PZ 3 / 4,M 4 bits for TORX® screws T 40 / 45 / 50 / 55,J 4 bits for Allen screws

Size 3 / 4 / 5 / 6 mm,3 wrenches, hexagon Size 1,27 / 1,5 / 2,0 mm.


82-part 101

eng/OP


www.hhw.de51.38

5



Quality Chrome-alloy steel. 51351

Set contentsxN 9 hexagonal bits with AS-Drive profile

Size 4 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 mm, J 3 bits for Allen screws

Size 3 / 4 / 5 mm, 1 reversible ratchet, 1 bit holder with plastic handle,1 handle with sliding piece, 1 ea. extension 54 and 150 mm, 1 Cardan joint.

v

N 10 hexagonal bits with AS-Drive profileSize 13 / 16 / 17 / 18 / 19 / 21 / 22 / 24 / 27 / 30 mm,

J 5 bits for Allen screwsSize 6 / 8 / 10 / 12 / 14 mm, 1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 130 and 255 mm, 1 Cardan joint,1 reversible ratchet with lever.


38-part 101

51351


NType50-part, with forged, tempered hexagonal bits andapplication tools in sheet steel case.



50-part 101

51352

Set contentsx

N 11 hexagonal bits Size 4 / 4,5 / 5 / 5,5 / 6 / 7 / 8 / 9 / 10 / 11 / 13 mm,

J 4 bits for Allen screwsSize 3 / 4 / 5 / 6 mm,

Q 3 bits for slotted screws0,8 x 4 / 1,0 x 5,5 / 1,2 x 6,5 mm,

D 2 bits for Phillips recess head screws PH 1 / 2,1 ea. extension 55 mm and 97 mm,1 Cardan joint, 1 handle with sliding piece, 1 bit holder with plastic handle,1 reversible ratchet with lever.

v

N 12 hexagonal bitsSize 10 / 11 / 12 / 13 / 14 / 15 / 17 / 19 / 22 / 24 /27 / 30 mm,

J 5 bits for Allen screws Size 7 / 8 / 10 / 12 / 14 mm,

Q 2 bits for slotted screws1,2 x 8 / 1,6 x 10 mm,

D 1 bit for Phillips recess head screws PH 3,1 ea. extension 125 mm and 250 mm,1 Cardan joint,1 reversible ratchet with lever.


Burrs by ATORN:

ATORN‘s high-quality grinding and cutting tools.

ß Hand tools


5


Type Chrome-plated, in sheet steel box. Quality Chrome-alloy steel.

51353 101 51353 110

51354 101

51354 110


32-part 101 10147-part 110 110

51353 - 51354





44-part 101

51355

Set contents 51353 101 + 51354 10118 socket wrench bits with AS-Drive profile size 8 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 /

22 / 24 / 27 / 30 / 32 / 34 mm,J 8 socket wrench bits for Allen screws size 4 / 5 / 6 / 7 / 8 / 10 / 12 / 14 mm,

1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 75, 130 and 255 mm, 1 Cardan joint.

Set contents 51353 110 + 51354 11019 socket wrench bits with AS-Drive profile size 8 / 9 / 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 /

21 / 22 / 24 / 27 / 30 / 32 / 34 mm,A 1 ea. double hexagonal bit with AS-Drive profile size 20,8 mm-13/16inch and 16 mm-5/8inch with

rubber insert for spark plugs, J 7 socket wrench bits for Allen screws size 4 / 5 / 6 / 7 / 8 / 10 / 12 mm,

13 combination wrenches size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 21 / 22 / 24 mm,1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 75, 130, and 255 mm, 1 Cardan joint.


VType58-part, in drawer plastic fitting (510 x 340 mm) with

PUR soft foam inserts for 1/4 inch (185 x 125 mm)and 1/2 inch (410 x 216 mm).QualityChrome-vanadium steel.

51356


58-part 101

51356

Set contentsxN 11 hexagonal bits size 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 13 / 14 mm,J 5 bits for Allen screws size 3 / 4 / 5 / 6 / 8 mm,Q 4 bits for slotted screws 0,6 x 3,5 / 0,8 x 4 / 1 x 5,5 / 1,2 x 8 mm,D 4 bits for Phillips recess head screws PH 1 / 2 / 3 / 4,E 3 bits for Phillips recess head screws PZ 1 / 2 / 3,

1 reversible ratchet, 1 handle with sliding piece, 1 bit holder with plastic handle,1 ea. extension 55 mm and 147 mm, 1 Cardan joint.

v

N 20 hexagonal bits size 10 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / 20 / 21 / 22 / 23 / 24 / 26 / 27 / 28 /30 / 32 mm,

1 reversible ratchet, 1 handle with sliding piece, 1 ea. extension 123 mm and 248 mm, 1 Cardan joint.

Set contentsA 18 bits for hexagonal sockets size 10 / 11/ 12 / 13 / 14 / 15 / 17 / 19 / 20 / 21 / 22 / 23 / 24 / 26 / 27 / 28 / 30 / 32 mm,J 7 bits, short, for Allen screws, size 5 / 6 / 7 / 8 / 10 / 12 / 14 mm,D 4 bits for Phillips recess head screws PH 1 / 2 / 3 / 4,E 4 bits for Phillips recess head screws PZ 1 / 2 / 3 / 4,M 5 bits for inner TORX® screws, T 27 / 30 / 40 / 45 / 50,

1 connector for bits 1/4 inch, 1 reversible ratchet,1 handle with sliding piece, 1 Cardan joint,1 ea. extension 125 and 248 mm.

eng/OP

• Socket Wrench Sets • Tool Set • Bit Rails • Socket Wrench Bits

www.hhw.de51.40

5

Tool Sets -Touring 1000-

NType47 tools in practical plastic case with practicalfolding handle. The case is impact-proof, resistantagainst oil and acids, resistant against environmen-tal influences. The tools sit tight in the case,therefore no rattling. External dimensions of case:435 x 345 x 135 mm.



47-part 101

51361

Set contentsN 9 hexagonal bits size 10 / 11 / 12 / 13 / 14 / 15 / 17 / 19 / 22 mm,

1 socket wrench bit for spark plugs, size 20,8 mm,1 reversible ratchet with lever 270 mm,1 handle with sliding piece 290 mm, 1 Cardan joint 70 mm,1 ea. extension 125 and 250 mm,11 combination wrenches size 6 / 7 / 8 / 10 / 11 / 12 / 13 / 14 / 15 / 17 / 19 mm (UD profile),

J 8 wrenches in holder, size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 mm,Q 1 ea. screwdriver 0,8 x 4,0 / 1,0 x 5,5 / 1,2 x 6,5 mm,Q 1 screwdriver for slotted head screws, 0,5 x 3,0 mm,D 1 ea. Phillips screwdriver PH 1 x 80 / 2 x 100 mm,

1 waterpump pliers 245 mm, 1 combination pliers 180 mm, 1 diagonal cutting pliers 160 mm,Q 1 voltage tester 3,0 mm,

1 folding knife, 1 small parts box, 1 machinist's hammer 300 g.


NTypeOuter square suitable for socket wrench bits nominalsize 12,5 (1/2inch). 2 additional inner squarewrench adapters for ratchets, sliding handles,extension pieces, etc. A strong magnet allows for asecure fastening of the rail to metal objects.Additional boreholes allow the fastening to non-me-tallic objects and walls. The bits are held securely by

the ball by means of turning them 90°. Turning them90° in the opposite direction will release the bits sothat they can be removed. Tools not included.

51374

for socket wrench bits length width weight 51374 …pcs. mm mm g

12 480 33 470 10016 580 33 550 101

51374

www.atorn.com


Tool carts by ATORN:

ATORN‘s high-quality workshop furnishings.

ß Hand tools


5



51375


51377N

51378



51381JWith OGV® profile.

51375

51377

51378

51379

51381

51375 - 51381

Hexagonal socket wrench bits (inch)

VQualityChrome-vanadium steel.

51390


3/8 38 14,5 1017/16 38 16,4 1021/2 38 18,3 103

9/16 38 20,5 1045/8 38 22,7 105


11/16 38 24,6 1063/4 38 26,8 107

13/16 38 28,6 1087/8 41,5 30,4 109

15/16 44 32,6 110


1 44 34,6 1111.1/16 46 36,3 1121.1/8 47 38,2 113

1.3/16 50 40,1 1141.1/4 50 42,3 115

51390

0 N V JSize l d1 51375 … 51377 … 51378 … 51379 … 51381 …mm approx. mm approx. mm

8 36 13,0 201 101 1019 36 14,0 202 102 102

10 38 15,0 203 103 103 103 10311 38 16,5 204 104 104 104 10412 38 18,0 205 105 105 105 10513 38 19,0 206 106 106 106 10614 38 20,5 207 107 107 107 10715 38 21,5 208 108 108 108 10816 38 22,5 209 109 109 109 10917 38 24,0 210 110 110 110 11018 38 25,5 211 111 111 111 11119 38 26,5 212 112 112 112 11220 38 28,0 213 113 113 11321 38 29,0 214 114 114 114 11422 41 30,5 215 115 115 115 11523 41 31,5 216 116 116 11624 41 33,0 217 117 117 117 11725 41 34,0 118 11826 41 35,5 219 119 11927 44 36,5 220 120 120 12028 44 38,0 221 121 12129 44 39,0 12230 44 40,5 223 123 123 12332 45 42,5 225 125 125 12534 45 45,5 126 12636 44,5 48,0 127

eng/OP

• Socket Wrench Bits • Screwdriver Bits

www.hhw.de51.42

5


51394 51395 51396

51394 - 51396

Long double hexagon socket wrench bits DIN 3124/ISO 2725

51402

51403

51405

51401

51401 - 51405



51395



N VSize l d1 51394 … 51395 … 51396 …mm approx. mm approx. mm

8 38 13,0 1019 38 14,0 102

10 38 15,5 103 103 10311 38 16,5 104 104 10412 38 18,0 105 105 10513 38 19,0 106 10614 38 20,5 107 107 10715 38 21,5 108 108 10816 38 22,5 109 109 10917 38 24,0 110 110 11018 38 25,5 111 111 11119 38 26,5 112 112 11220 38 28,0 113 113

N VSize l d1 51394 … 51395 … 51396 …mm approx. mm approx. mm21 38,0 29,0 114 114 11422 41,5 30,5 115 115 11523 41,5 31,5 11624 41,5 33,0 117 117 11725 41,5 34,0 11826 41,5 35,5 11927 44,0 36,5 120 120 12028 44,0 38,0 12129 44,0 39,0 12230 44,0 40,5 123 123 12332 44,0 42,5 125 125 12534 44,0 45,0 126

TypeLong, chrome-plated, drop-forged and polished.ApplicationFor deeply set screws and protruding bolts.QualityChrome-vanadium steel.

51401


51403



Note:No. 109 with rubber insert for spark plugs.

0 N VSize l d1 51401 … 51402 … 51403 … 51405 …mm mm approx. mm

10 82 15,5 101 101 10111 82 16,5 10212 82 17,5 103 10213 82 19,0 104 103 103 10314 82 20,0 105 104 104 10415 82 21,5 10616 82 23,0 107 105 106 10517 82 24,0 108 106 108 10618 82 24,5 109 107 109 10719 82 27,0 110 108 110 10820 82 28,0 111

20,8 82 28,5 112 10921 82 28,5 113 110 113 11022 82 30,0 114 111 114 11123 82 31,5 11524 82 32,5 116 112 115 11226 82 35,0 11727 82 36,5 118 113 117 11330 82 40,0 119 114 119 11432 82 43,0 120 115 12034 82 45,0 116

ß Hand tools


5

Double hexagon socket wrench bits (inch) DIN 3124/ISO 2725

,TypeImperial sizes. With Dynamic-Drive profile.nickel-plated and chrome-plated, highly polished.



3/8 38 14,5 1017/16 38 16,6 1021/2 38 18,8 103

9/16 38 20,8 10419/32 38 21,6 105

5/8 38 22,9 10611/16 38 24,7 107

3/4 38 26,6 10825/32 38 27,9 109


13/16 39 28,7 1107/8 39 30,7 111

15/16 41 32,7 1121. 42 34,7 113

1.1/16 44 36,6 1141.1/8 46 38,6 115

1.3/16 47 40,4 1161.1/4 47 42,3 117

51409

Screwdriver bits51410 - 51411

TypeChrome-plated, blades burnished.QualityVanadium special steel.

51410

051411 N

51410 102-106

51410 201-203

0 NBlade thickness x width l1 l2 d 51410 … 51411 …mm/size approx. mm approx. mm approx. mmQ 1,2 x 8 22 60 22,5 102 102Q 1,6 x 10 22 60 22,5 104 104Q 2,0 x 12 22 60 22,5 105 105Q 2,5 x 14 20 60 22,5 106 106D PH 2 22 60 22,5 201 201D PH 3 22 60 22,5 202 202D PH 4 22 60 22,5 203 203E PZ 2 22 60 22,5 301E PZ 3 22 60 22,5 302E PZ 4 22 60 22,5 303

51410 301-303

51411 102-106

51411 201-203

Sets of hexagon screwdrivers

NQualityVanadium special steel.

51415Type9-part: size 5 / 6 / 7 / 8 / 9 / 10 / 12 / 14 / 17 mm, in sheet steel case.

51416TypeUS inch sizes.9-part: 3/16 / 7/32 / 1/4 / 9/32 / 5/16 / 3/8 / 1/2 / 9/16 / 5/8, in sheet steel case.

51415

mm inchSet contents 51415 … 51416 …

9-part 101 101

51415 - 51416

Sets of hexagon screwdrivers

VType12-part, in sheet steel case.



12-part 101

51420

Set contentsJ 8 socket wrench bits size 5 / 6 / 8 / 10 / 12 / 14 / 17 / 19 mm,

1 reversible ratchet and 1 handle with sliding piece,1 ea. extension 125 and 248 mm.

eng/OP

• Screwdriver Bits • Sets of TORX®

www.hhw.de51.44

5

Hexagon screwdriver bits


51424

0

51426N

51427


51428V

51424 51427

51428

51426

51424 - 51428

Hexagon ball head screwdriver bits

51431NTypeWith ball-retaining groove and non-slip knurling.Sleeve chrome-plated, burnished blade.ApplicationTotal flex angle approx. 15-20°.QualityPointed tip made of vanadium special steel.

51432VTypeSleeve chrome-plated, blade steel-grey.ApplicationFor operation in hard-to-reach areas, flex angle 25°.QualityChrome-vanadium steel, blades made of specialsteel.

51431

N VSize l 51431 … 51432 …mm mm

5 140 1016 140 101 1027 140 102 1038 140 103 104

10 140 104 10512 140 105 106

51432

51431 - 51432

Sets of TORX® screwdrivers51436 - 51437

NApplicationFor inner TORX® screws.QualityVanadium special steel.


51436Type9-part, short (55 mm):T 20 / 25 / 27 / 30 / 40 / 45 / 50 / 55 / 60, in sheet steel case.

51437Type18-part, 1 ea. short (55 mm) and long (100 mm) shape:T 20 / 25 / 27 / 30 / 40 / 45 / 50 / 55 / 60, in sheet steel case.

51436

51437Set contents 51436 … 51437 …

9-part 10118-part 101

0 N VSize l l l l d 51424 … 51426 … 51427 … 51428 …mm mm mm mm mm approx. mm

4 57 – 60 60 22,5 101 101 1015 57 60 60 60 22,5 102 102 102 102

L 5 – 180 120 180 22,5 104 104 1046 57 60 60 60 22,5 105 105 105 105

L 6 – 140 120 137 22,5 107 107 1077 57 60 60 60 22,5 109 109 109 109

L 7 – – 120 – 22,5 1108 57 60 60 60 22,5 111 111 111 111

L 8 – 120 120 119 22,5 113 113 11310 57 60 60 60 23,0 115 115 115 115

L 10 – 140 140 141 23,0 116 116 11612 57 60 60 60 23,5 118 118 118 118

L 12 – – 140 – 23,5 11914 57 60 60 60 25,0 120 120 120 120

L 14 – – 140 – 23,5 12117 57 60 60 60 28,0 122 122 122 12219 57 60 60 60 30,0 124 123 123 123

ß Hand tools


5

Set of TORX® screwdrivers

VType10-part, in black, impact-proof plastic case withPUR soft foam insert.ApplicationFor inner TORX® screws.



51441

Set contents3 bits 1/4 inch, T 8 / T 10 / T 15,3 bits 3/8 inch, T 20 / T 25 / T 30,4 bits 1/2 inch, T 40 / T 50 / T 55 / T 60.

51441


10-part 101


TypeChrome-plated, drop-forged, blades burnished.ApplicationFor inner TORX® screws.QualityChrome-vanadium steel.

Note:TORX®selector see cat.-no. 37930.

51444

051445N

51446


51447V

51444- 51447

51445

51446

51447

51444

ResisTORX® screwdriver bits

VTypeSleeve chrome-plated, blade steel-grey.ApplicationFor inner TORX® screws with pilot.

QualityChrome-vanadium steel, blades made of specialsteel.

Note:TORX®selector see cat.-no. 37930.

51451

Size l d 51451 …T mm mm

20 55 23 09825 55 23 09927 55 23 10030 55 23 10140 55 23 102

Size l d 51451 …T mm mm

45 55 23 10350 55 23 10455 56 23 10560 56 23 106

51451

0 N VSize l d 51444 … 51445 … 51446 … 51447 …

T approx. mm approx. mm20 55 23 101 101 101 101

L 20 100 23 102 10225 55 23 103 103 103 103

L 25 100 23 104 10427 55 23 105 105 105 105

L 27 100 23 106 10630 55 23 107 107 107 107

L 30 100 23 108 10840 55 23 109 109 109 109

L 40 100 23 110 11045 55 23 111 111 111 111

L 45 100 23 112 11250 55 23 113 113 113 113

L 50 100 23 114 11455 55 24,6 115 115 115 115

L 55 100 23 116 11660 55 24,6 117 117 117 117

L 60 100 23 118 11870 60 25,7 119

eng/OP

• Sets of TORX®

www.hhw.de51.46

5

TORX® set

NType 34-part, in sheet steel case. Application For inside and outside TORX® screws.

Quality Vanadium 31CrV3.


51452

Set contentsx M 8 bits for inner TORX® screws T8 / 9 / 10 / 15 / 20 / 25 / 27 / 30,

4 6 socket wrench bits for outer TORX® screws E4 / 5 / 6 / 7 / 8 / 10. v M 5 bits for inner TORX® screws, short T40 / 45 / 50 / 55 / 60,

M 9 socket wrench bits for inner TORX® screws, long T20 / 25 / 27 / 30 / 40 / 45 / 50 / 55 / 60, 4 6 socket wrench bits for outer TORX® screws, E12 / 14 / 16 / 18 / 20 / 24.


34-part 101

51452

TORX® set51455

NType17-part, in sheet steel case.ApplicationFor inside and outer TORX® screws.



51455

Set contentsM 9 bits for inner TORX® screws, T20 / 25 / 27 / 30 / 40 / 45 / 50 / 55 / 60 mm,4 8 bits for outer TORX® screws, E10 / 11 / 12 / 14 / 16 / 18 / 20 / 24 mm.


17-part 301

TORX® set51456

VType 9-part, in metal case. Application For inside and outside TORX® screws.



Set contentsM 5 socket wrench bits for inner TORX® screws, T30 / 40 / 45 / 50 / 55, 4 4 socket wrench bits for outer TORX® screws, E10 / 12 / 14 / 16.

51456


9-part 301

Set of TORX® socket wrenches




51457

Set contentsx M 2 bits for inner TORX® screws T8 / 9,

4 3 bits for outer TORX® screws E4 / 5 / 6, C 7 bits TORX® with borehole T10 / 15 / 20 / 25 / 27 / 30 / 40.

w M 5 bits for inner TORX® screws T10 / 15 / 20 / 25 / 27, 4 4 bits for outer TORX® screws E7 / 8 / 10 / 12,

1 bit holder with hexagon socket 1/4 inch. v M 6 bits for inner TORX® screws T30 / 40 / 45 / 50 / 55 / 60,

4 6 bits for outer TORX® screws E11 / 14 / 16 / 18 / 20 / 24,M 4 1 TORX® gauge for inner TORX® screws T10-60 and TORX® screws E6-16.


35-part 301

51457

ß Hand tools


5

TORX® tool kits 51458

VType 29-part, in black, impact-proof plastic case withPUR soft foam insert.



51458

Set contents4 4 ring wrenches for outer TORX® screws, E6 x 8 / 10 x 12 / 14 x 18 / 20 x 24,

1 adapter J 5/16 inch x z 3/8 inch, 1 adapter J 5/16 inch x z 1/2 inch, 1 adapter J 1/4 i nch x z 1/4 inch.

x 4 4 socket wrench bits for outer TORX® screws, E5 / 6 / 7 / 8,M 7 bits for inside TORX® screws,

T 10 / 20 / 25 / 27 / 30 (length 26 mm), T 25 (length 65 mm), T 30 with hole (length 26 mm).

y M 3 bits for inside TORX® screws, T40 / 45 / 50. w 4 3 socket wrench bits for outer TORX® screws, E10 / 12 / 14. v 4 3 socket wrench bits for outer TORX® screws, E10 / 12 / 14,

2 screwdriver socket wrench bits for inner TORX® screws, T55 / 60.


29-part 101

TORX® tool kits

VType58-part, in black, impact-proof plastic case withPUR soft foam insert.



51459


58-part 101

51459

Set contents4 4 ring wrenches for outer TORX® screws, E 6 x 8 / 10 x 12 / 14 x 18 / 20 x 24,M 10 screwdrivers for inner TORX® screws, T 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30,M 11 angled screwdrivers for inner TORX® screws, T 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 /

30 / 40,x 4 5 socket wrench bits for outer TORX® screws, E 4 / 5 / 6 / 7 / 8,

C 12 bits ResisTORX® with borehole, 26 mm, (T 6 without borehole),T 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 25 (110 mm) / 27 / 30 / 40,1 adapter J 1/4 inch x z 1/4 inch,1 adapter J 1/4 inch x z 3/8 inch,1 bit reversible ratchet 115 mm (20 teeth),

w 4 4 socket wrench bits for outer TORX® screws, E 10 / 11 / 12 / 14,M 2 screwdriver bits for inner TORX® screws, T 40 / 45,

v 4 4 socket wrench bits for outer TORX® screws, E 16 / 18 / 20 / 24,M 3 screwdriver bits for inner TORX® screws, T 50 / 55 / 60.

Set of TORX® socket wrenches

VType9-part, in black, impact-proof plastic case with PURsoft foam insert.ApplicationFor outer TORX® screws.



51463

Set contents4 3 socket wrench bits 1/4 inch, E 4 / E 5 / E 6,4 3 socket wrench bits 3/8 inch, E 8 / E 10 / E 12,4 3 socket wrench bits 1/2 inch, E 14 / E 18 / E 20.


9-part 301

51463

eng/OP

• Socket Wrench Bits • Screwdriver Bits • Reversible Ratchets

www.hhw.de51.48

5


ApplicationFor outer TORX® screws.


51465

051473VType Chrome-plated, polished. Quality Chrome-vanadium steel.

51465 51473

51465 - 51473

Allen key XZN-/RIBE CV screwdriver set51476

51476

VType9-part, in metal case.


Set contentsH 7 bits XZN M 5 /6 / 8 / 10 / 12 / 14 / 16,R 2 socket wrench bits RIBE CV M 8 /10.


9-part 301

Allen XZN screwdriver bits 51480

NTypeChrome-plated, blade burnished.ApplicationFor Trisquare socket head screws (Allen key XZN).


Size l d 51480 …XZN mm mm

5 55 23 3016 55 23 302

L 6 100 23 3038 55 23 304

L 8 100 23 305

Size l d 51480 …XZN mm mm

10 55 23 306L 10 100 23 307

12 55 23 308L 12 100 23 309

RIBE CV screwdriver bits

VTypeChrome-plated, drop-forged, blades burnished.ApplicationFor inner spline screws (RIBE CV).


51484

51484

Size l d 51484 …RIBE CV mm mm

5 63 23 1016 63 23 1028 63 23 103

10 63 23 104

Size l d 51484 …RIBE CV mm mm

12 63 23 10514 63 24,6 10616 63 24,6 107

0 VSize Length 51465 … 51473 …

E mm10 38,0 101 30111 38,0 102 30212 38,0 103 30314 38,0 104 30416 38,0 105 305

0 VSize Length 51465 … 51473 …

E mm18 38,0 106 30620 38,0 107 30722 38,0 10824 38,0 10924 41,2 308

ß Hand tools


5

Reversible geared ratchets DIN 3122/ISO 331551503

NTypeFinely toothed and robust thanks to double catch,with square piece.QualityChrome-vanadium steel.

51503 102Square piece 51503 101

51503 102


Ratchet 270 101Square piece 38 102


51506

51507

51508

51510 101

51510 102

51506 - 51510

Reversible ratchet DIN 3122/ISO 3315

NTypeWith reverse lever. Finely toothed, ratcheting angle6°, non-slip 2-component handle with attachmenteye. Ball lock, with quick-release push button.

QualityVanadium steel 31CrV3. 51512


51512


Digital slide callipers by ATORN:

ATORN‘s high-quality measuring tools.

TypeChrome-plated, extremely robust ratchets withturning knob for clockwise and counterclockwi-se operation and ergonomically-shaped handlemade of plastics.QualityChrome-vanadium steel.

51506 101NFinely toothed (72 teeth, ratcheting angle 5°),with ball lock.

51507

Finely toothed (60 teeth, ratcheting angle 6°).QualityChrome-alloy steel.

51508 201VFinely toothed (72 teeth, ratcheting angle 5°), for use on screws even in hard-to-reach areas. With thumb rest and quickly releasable safetylock. One-hand operation: easily turning plasticwheel for reverse operation. More safety throughlarger space between ratchet and screw. Largecorner moulding offers more Room for preciseoperation.

51510 101-102JFinely toothed (72 teeth, ratcheting angle 5°).The thumb rest enables the user to press onto theratchet head without activating the reverse switch.Quick reversal thanks to one-hand operation.

51510 102Extra long ratchet 400 mm.


mm250 101255 201265 201270 101

XL 400 102

eng/OP

• Reversible Ratchets

www.hhw.de51.50

5


TypeChrome-plated, extremely robust ratchets withclockwise and counterclockwise operation andergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51515 201

0TypeWith reverse lever and quick-release push button.

51517 101NTypeWith reverse lever, quick-release push button.Centre position arrest and ball lock. 32 teeth,ratcheting angle 11,25°.

51518 101

TypeWith reverse lever, 36 teeth.QualityChrome-alloy steel.

51518 102

Type With reverse lever, QuickRelease safety lock and2-component handle, 36 teeth. Quality Chrome-alloy steel.

51519 201VTypeWith reverse lever, polished, 32 teeth.

51519 202VTypeWith reverse lever, polished, 32 teeth. With safetylock and quick-release push button.

51513 100ZTypeWith reverse lever.

51513 100

51515

51517

51518 101

51519 201

51519 202

51518 102

51513 - 51519

One-hand reversible ratchet DIN 3120/ISO 117451522

,TypeNickel-plated and chrome-plated, highly polished.Smooth running one-hand reverse ring on thehandle for reversal of operation by a simple, shortturn. Integrated quick-turning disc on the squaresection for easier tightening and loosening of screw

connections. Unlocking device of ball catch foreffortless and quick push-button exchange of socketwrench bits. Fine-pitched teeth (60 teeth), turningangle 6°. Plastic handle with attachment eye.QualityVanadium-extra.

51522


51519 202

0 N V ZOverall length 51515 … 51517 … 51518 … 51519 … 51513 …

mm250 100255 201

265,5 101265,5 102

270 101275 201275 202

ß Hand tools


5

Telescopic reversible ratchet

TypeInfinitely adjustable from 380 - 500 mm. Withreverse lever, reversible, quick-release push button,ball lock, and ergonomically shaped 2-component

handle. Highly polished chrome-plated.QualityChrome-vanadium steel.

51523

Adjusting range 51523 …mm

380 - 500 101

51523

Reversible ratchets51527

VTypeWith reverse lever. Chrome finish and polished.Extremely robust ratchet with clockwise and

counter-clockwise operation, swivelling head andergonomically-shaped handle made of plastics.QualityChrome-vanadium steel.

51527


Readyflex® Freiraumknarre®51530 - 51532

Overall length 51530 … 51532 …mm260 201280 101

51530

51532

PApplicationThis ratchet combines all the advantages of aratchet with a flexible lever arm with those of aratchet with a rigid lever arm. It guarantees fullleverage, especially in angled positions. It istherefore suitable for application in hard-to-reachareas.QualityChrome-vanadium steel.

51530TypeReverse function ring, 7 steps, lockable by meansof yellow Flex button, finely toothed (72 teeth),chrome-plated. With moveable lever arm.Thesliding guide in inner ring (1) enables the user topress onto the ratchet head without activating thereverse switch. Reverse function by means of one-hand operation on outer ring (2).

51532TypeReverse lever, 7 switch steps, joint lockable bymeans of yellow Flex button. Locking mechanism fortools by means of red button in ratchet head.

Zyklop ratchet

sTypeFlywheel design and non-slip quick-action sleeve forhigh working speed. Swivelling ratchet head. Presetpositions at 0°, 75°, and 90° in both directions.Usable as a standard screwdriver when in the 0°

position. Quick-release push button, clockwise andcounterclockwise operation, finely toothed, smallratcheting angle of 5° - 6°. Multi-componentKraftform handle for effortless work.

51534



The locking mechanism accelerates mounting andremoving of the socket wrench bits and extensions.The ball lock secures the socket wrench bits and theaccessories and also provides additional safety duringthe application. Simply press the release button andtool exchange is possible in any defined position.



51534

eng/OP

• Socket Accessories • Extensions • Adapter • Ring Wrenches

www.hhw.de51.52

5

Socket accessories


51535

051537DBGMNTypeGround. Easy locking and unlocking by turning thehandle.ApplicationLock against unintended unlocking.

51538N

51538 202NCrankTypeWith rotating ergonomically-shaped handle.

51539


51540

TypeWith QuickRelease safety lock.QualityChrome-alloy steel.

51541V

51535 201

51538 202

51535 204 51535 20551539 106

51537 101

51540 101

51540 103

51535 - 51541

Extension pieces


51550

051551NWith release. Safety ring to prevent unintentionalrelease of the socket wrench bit.

51552N

51553


51554V

51556J

51560


51550 102

51553 301

51560 102

51556 204

51551 102

51550 - 51560

51535 203

51537

0 N N V51535 … 51537 … 51538 … 51539 … 51540 … 51541 …

Handle with sliding piece 201 101 201 101 101 201Crank 202

Cardan joint 203 203 103 103 203Adapter 1/2inch . x 3/8inch z 204 204 104 204Adapter 1/2inch . x 3/4inch z 205 205 105 205

FixGRIP adapter 1/2inch . x 3/4inch z 106

0 N N V JLength 51550 … 51551 … 51552 … 51553 … 51554 … 51556 … 51560 …

approx. mm52 300 10175 101 201 301 201

125 102 101 202 302 202 202130 102250 103 102 203 303 203 203255 103500 204

ß Hand tools


5

Swivelling extensions51562

VTypeChrome-plated, polished.ApplicationWith ball-type, conical outer square. Allows a flexangle to any direction of 12,5°.


51562 201

51562 202

51562 203Length 51562 …

mm46 201

123 202248 203

Extendable extension

ApplicationBy pulling down the locking sleeve, the inner partcan be pulled out (7-x length adjustment). 2 step system: The first step is used for secure hold of the socketwrench bits in a straight position.The second step (achieved by pulling the socketwrench bit forward) uses the built-in Cardan functionfor a flex angle of up to 15°.The tool can also be used as an extendablescrewdriver.


51563

Length adjustment 51563 …approx. mm

260 - 415 101

51563

Adapter sets

VType 6-part, chrome-plated. 1/4 inch . x 3/8 inch z, 3/8 inch . x 1/4 inch z, 3/8 inch . x 1/2 inch z, 1/2 inch . x 3/8 inch z, 1/2 inch . x 3/4 inch z, 3/4 inch . x 1/2 inch z.


51565


6-part 101

3 4

Open double hexagonal ring wrenches (crowfoot wrenches)

VType Chrome-plated, with inside square drive. Application Especially for working in hard-to-reach places.


51568

Size 51568 …mm

30 10132 10236 103

Size 51568 …mm

41 10446 105

eng/OP

• Socket Wrench Sets • Socket Wrench Bits • Screwdriver Bits

www.hhw.de51.54

5


Type Chrome-plated, in sheet steel box. With Quick-Re-lease system (one-hand safety lock).

Quality Chrome-alloy steel. 51571 201

51571 202

Set contents 51571 201N 10 hexagonal bits size 22 / 24 / 27 / 30 / 32 /

34 / 36 / 41 / 46 / 50 mm, 1 reversible ratchet, 1 handle, 1 sliding piece, 1 angle joint,1 ea. extension 200 and 400 mm.

Set contents 51571 202 N 9 hexagonal bits size 32 / 34 / 36 / 38 / 41 /

46 / 50 / 55 / 60 mm, 1 reversible ratchet, 1 handle, 1 sliding piece, 1 angle joint, 1 ea. extension 200 and 400 mm.


16-part 20115-part 202

3 4


VType 15-part, in metal case.

51572

Set contentsA 10 double hexagonal bits size 22 / 24 / 27 / 30 /

32 / 36 / 38 / 41 / 46 / 50 mm, 1 reversible ratchet head, 1 turning bar with ball lock and locking pin,1 sliding sleeve with ball lock,1 ea. extension 200 and 400 mm.


15-part 101

51572 3 4


51574

51573 51575

51573 - 51575 3 4




Set contentsN 10 hexagonal bits size 22 / 24 / 27 / 30 / 32 / 36 / 38 / 41 / 46 / 50 mm,

1 reversible ratchet, 1 handle with sliding piece,1 ea. extension 200 and 400 mm.


14-part 201

3 4


51573N

51575

QualityHPQ high-performance steel.

51574V


19 50 28,0 30221 51 28,0 303 30322 51 33,0 304 304 30424 51 35,0 305 305 30527 55 39,0 306 306 30630 59 42,5 308 308 30832 59 45,0 309 309 30934 59 48,0 311 311 311


36 62 50,0 313 313 31338 62 52,5 314 31441 68 56,5 315 315 31546 73 63,0 317 317 31750 75 68,0 318 318 31855 82 74,0 319 319 31960 88 80,5 320 320

Size l d1 51577 …mm mm mm

21 51,5 32,0 20322 51,5 33,3 20424 51,5 35,8 20627 54,5 39,6 20930 57,5 43,3 212


32 57,5 45,8 21336 59,5 50,8 21741 62,5 57,1 21946 65,5 63,3 22150 68,5 68,3 222

ß Hand tools


5

Long hexagonal socket wrench bits DIN 3124/ISO 272551576

JType With OGV profile® and safety lock.

51576


19 87,5 30,0 30221 87,5 32,0 30322 87,5 33,5 30423 87,5 35,8 30524 87,5 35,8 30626 87,5 35,8 30727 87,5 39,6 30829 87,5 42,1 30930 87,5 43,3 310


32 87,5 45,8 31133 87,5 48,0 31234 87,5 48,3 31335 87,5 50,0 31436 87,5 50,8 31538 87,5 54,1 31641 87,5 57,1 31742 87,5 59,5 318

3 4


NTypeWith UD profile. Chrome-plated, drop-forged.QualityChrome-vanadium steel.

51577

51577

Hexagonal screwdriver bits

51581

51582

51581 - 51582


VApplication For inner TORX® screws.



51583

Size Length 51583 …T mm

60 80 10170 80 10280 80 103

Size Length 51583 …T mm

90 80 104100 80 105

51583

3 4

3 4

3 4

ApplicationFor Allen screws, for high loads, narrow tolerances.

51581NTypeChrome-plated, centres burnished, with non-slipknurling.QualityVanadium special steel.

51582

TypeChrome-plated.QualityChrome-alloy steel.

NSize l d 51581 … 51582 …mm mm approx. mm

14 80 36 201 10117 80 36 202 10219 80 36 203 10322 80 39 204 104

eng/OP

• Reversible Ratchets • Socket Accessories • Extensions • Socket Set • Socket Wrench Bits

www.hhw.de51.56

5

Reversible geared ratchets DIN 3122/ISO 331551584

NTypeChrome-plated, with locking pin and internaltoothing (ratcheting angle 10°). With square piece.


51584 202Square piece

51584 201

51584 202


Ratchet 510,0 201Square piece 51,5 202

3 4

Reversible ratchet DIN 3122/ISO 331551586

NTypeChrome-plated, extremely robust ratchet withswitch knob for clockwise and counterclockwiseoperation, locking pin and internal toothing

(ratcheting angle 7,2°). QualityVanadium 31CrV3. 51586


3 4

51590 102

51591

Socket accessories

51592 102

51595 203

51593 101

51592 - 51595

Reversible ratchets DIN 3122/ISO 331551588 - 51591 3 4

3 4

Extension pieces51596 - 51598

51596

51598

3 4

51588

51589

51590 101

TypeChrome-plated, extremely robust ratchet withclockwise and counter-clockwise operation andlocking pin. QualityChrome-vanadium steel.

51588NTypeWith switch knob. Finely toothed (ratcheting angle 5°).

51589VType With reverse lever. Ratchet (32 teeth) with ball lock.Shank with ejector bolt for locking pin.

51590 101

Ratchet headTypeWith reverse lever. 36 teeth. Without handle (cat.-no. 51590 102). With Quick-Release system (one-hand safety lock).QualityChrome-alloy steel.

51590 102

HandleApplicationFor ratchet head cat.-no. 51590 101.QualityChrome-alloy steel.

51591JTypeWith switch knob. Finely toothed (ratcheting angle 5°). Calendered.


Type mmRatchet assembly 505 201Ratchet assembly 620 201 101

Ratchet head 165 101Handle 510 102


51592N

51593V

51595


N V51592 … 51593 … 51595 …

Handle with sliding piece 101Cardan joint 102

Adapter 3/4 inch . x 1/2 inch z 103 103 203Adapter 3/4 inch . x 1 inch z 104 204


51596N

51597V

51598


N VOverall length 51596 … 51597 … 51598 …

mm200 101 101 102400 102 102 103

ß Hand tools


5




51600

Set contents10 socket wrench bits, double hexagon with UD profile size 36 / 41 / 46 / 50 / 55 / 60 / 65 / 70 / 75 / 80 mm,1 ea. reversible ratchet, handle with sliding piece,1 ea. extension 200 and 400 mm.


15-part 101

51600


NTypeWith UD profile. Chrome-plated, drop-forged.


51603


36 70 53,9 20341 70 60,1 20446 75 66,4 20550 75 71,4 20655 78 77,6 207


60 83 83,9 20865 86 90,1 20970 90 96,4 21075 93 102,6 21180 95 108,9 212

51603

Reversible ratchets with handle bar DIN 3124/ISO 2725

NTypeChrome-plated, head finely ground. Extremelyrobust ratchet with reverse lever for clockwise andcounter-clockwise operation, locking pin and centreposition arrest. Ratcheting angle 11,25°.


51606

51606


Socket accessories

NTypeChrome-plated, drop-forged.QualityVanadium 31CrV3.

51609 101Sliding T-barSliding piece with ball stop.

51609

51609 101

51609 102

Length 51609 …mm

Handle bar 700 101Adapter 1 inch . x 3/4 inch z 75 102

Extension pieces51612

NTypeChrome-plated, drop-forged.


51612

Overall length 51612 …mm200 101400 102

eng/OP

• Impact tools

www.hhw.de51.58

5

Hexagon servo screwdriver bits 51614

TypeDrive: 1/4 inch square-end DIN 3121 shape G 6,3, Output: Allen DIN 475/2.

Quality Chrome-vanadium special steel. 51614

Size L D1 D2 T 51614 …mm mm mm mm mm

6 23 10,0 13 6,0 1067 23 11,3 13 6,0 1078 23 12,5 13 6,0 108

10 23 15,0 13 7,0 110


11 23 16,3 13 8,0 11112 23 17,0 13 8,0 11213 23 18,8 13 8,0 113

Hexagon servo screwdriver bits, with magnet

TypeWith strong permanent magnet.Drive: 1/4 inch square-end DIN 3121 shape G 6,3, Output: Allen DIN 475/2.

QualityChrome-vanadium special steel.

51616

Size Size L D1 D2 T 51616 …mm inch mm mm mm mm

5 – 23 8,8 13 3,0 1015,5 – 23 9,5 13 3,0 102

6 – 23 10,0 13 3,0 1037 – 23 11,3 13 3,0 1048 – 23 12,5 13 3,0 1059 – 23 13,8 13 4,0 106

10 – 23 15,0 13 4,0 107

Size Size L D1 D2 T 51616 …mm inch mm mm mm mm

11 – 23 16,3 13 5,0 10813 – 23 18,8 13 5,0 109– 1/4 23 10,3 13 3,0 110– 5/16 23 12,5 13 3,0 111– 3/8 23 15,0 13 4,0 112– 1/2 23 18,8 13 5,0 113

51616

Hexagon servo screwdriver bits, long with magnet

TypeLong type, with spring-loaded magnet. Drive: 1/4 inch square-end DIN 3121 shape G 6,3, Output: Allen DIN 475/2.


51617

51617


7 50 11,3 13 4,0 1018 50 12,5 13 4,0 102

10 50 15,0 13 4,0 10313 50 18,8 13 6,0 104

Servo screwdriver bit accessories


51613 301-302TypeDrive: 1/4 inch square-end DIN 3121 shape G 6,3,Output: 1/4 inch outer square DIN 3121 shape E -with spring-loaded pin.

51613 401TypeWith strong permanent magnet. Drive: 1/4 inch square-end DIN 3121 shape G, Output: 1/4 inch Allen DIN 3126 shape D 6,3.

51613 401

51613 301-302

E A D2 L 51613 …inch inch mm mm

Extension 1/4 1/4 13 50 301Extension 1/4 1/4 13 150 302Bit holder 1/4 D 6,3 13 62 401

51613

Servo screwdriver connecting piece

TypeWith quick-change toolholder.Drive: 1/4 inch square-end DIN 3121 shape G 6,3,output: outer square DIN 3121 - with ball lock.

QualityChrome-vanadium special steel. 51627

E A D2 L L1 L2 51627 …inch inch mm mm mm mm

1/4 1/4 13 35 28 10 101

51627

ß Hand tools


5

Hexagon servo screwdriver bits51615

TypeDrive: 3/ 8inch square-end DIN 3121 shape G 10, Output: Allen DIN 475/2.



8 30 14,0 19 6,0 20310 30 16,0 19 7,0 20511 30 17,5 19 8,0 20612 30 19,0 19 9,0 20713 30 20,0 22 9,0 208


14 30 21,0 22 9,0 20915 30 22,0 22 11,0 21016 30 24,0 22 11,0 21117 30 25,0 22 11,0 212

Hexagon servo screwdriver bits, with magnet

TypeWith strong permanent magnet.Drive: 3/8 inch square-end DIN 3121 shape G 10, Output: Allen DIN 475/2.


51619


8 30 14,0 19 3,0 1019 30 15,0 19 4,0 102

10 30 16,0 19 4,0 10311 30 17,5 19 5,0 10413 30 20,2 22 5,0 106


14 30 21,0 22 6,0 10715 30 22,0 22 6,0 10816 30 24,0 22 6,0 10917 30 25,0 22 6,0 110

51619

Hexagon servo screwdriver bits

Type Drive: 3/8 inch square-end DIN 3121 shape G 10, Output: outer hexagon DIN/ISO 2963.

Quality Chrome-vanadium special steel.

51620

Size L D2 51620 …mm mm mm

5 50 19 1016 50 19 1028 50 19 103


10 50 19 10412 50 19 10514 50 19 106

51620

Inner TORX® servo screwdriver bits

Type Drive: 3/8 inch square-end DIN 3121 shape G 10, Output: TX for inner TORX® screws.



51628

Size L D2 51628 …T mm mm

20 50 19 10125 50 19 10227 50 19 103


30 50 19 10440 50 19 105

51628

eng/OP

• Impact tools

www.hhw.de51.60

5

Outer TORX® servo screwdriver bits 51618

TypeDrive: 3/8 inch square-end DIN 3121 shape G 10, Output: E profile for all TORX® screws.



51618

size L D1 D2 T 51618 …E mm mm mm mm5 32 9,0 19 4,0 2016 32 10,2 19 4,0 2027 32 10,2 19 5,0 2038 32 10,5 19 5,0 204

size L D1 D2 T 51618 …E mm mm mm mm

10 32 12,5 19 6,0 20512 32 14,9 19 8,0 20614 32 17,2 19 9,0 207



51621 101-302Type Drive: 3/8 inch square-end, DIN 3121 shape G 10, Output: outer square, DIN 3121 shape E - withspring-loaded pin.

51621 303Type Drive: 3/8 inch square-end, DIN 3121 shape G 10, Output: 5/16 inch Allen DIN 3126 shape D 8.

51621 304Type Drive: 3/8 inch square-end, DIN 3121 shape G 10, Output: 1/4 inch Allen DIN 3126 shape D 6,3.

51621

51621 101

51621 201-203

51621 301-302

51621 303

51621 401-402

51621 501-502

51621 304


TypeWith quick-change toolholder. Drive: 3/8 inch square-end DIN 3121 shape G 10,output: outer square, DIN 3121 - with ball lock.


51622

51622


3/8 3/8 20 46 35 17 101

E A D2 L 51621 …inch inch mm mm a

Ball joint 3/8 3/8 22 60 – 101Extension 3/8 3/8 19 75 – 201Extension 3/8 3/8 19 150 – 202Extension 3/8 3/8 22 300 – 203

Adapter 3/8 1/4 19 32 – 301Adapter 3/8 1/2 22 36 – 302

Bit holder 3/8 D 8 19 38 – 303Bit holder with quick-exchange mount 3/8 1/4 19 45 – 304

Rubber ring – – 19 – 10 pcs. 401Rubber ring – – 22 – 10 pcs. 402

Safety pin – – 19 – 10 pcs. 501Safety pin – – 22 – 10 pcs. 502

. a= Sales are restricted to the packaging units mentioned

in the catalogue. Purchase orders must be in units.

ß Hand tools


5

Hexagon servo screwdriver bits, plastic-covered

TypePlastic-coated in order to prevent damage toaluminium wheelsPlastic sheath can be taken off ifnecessary (low distance between wheel nut andwheel rim borehole). Different colours for differentsizes.

51623 101

51623 201 51623 202 51623 203

Set contents Size 51623 …mm

3-part 17 / 19 / 21 101

Size d1 l Torque Colour 51623 …mm mm mm max. Nm

17 27 85 450 blue 20119 29 85 550 yellow 20221 31 85 550 red 203

51623

Inner TORX® servo screwdriver bits

Type Drive: 1/2 inch square-end DIN 3121 shape G 12,5, Output: TX for inner TORX® screws.



51632


30 55 25 20140 55 25 20250 55 25 203


55 55 25 20460 55 25 205

Hexagon servo screwdriver bits51624 - 51626

Type Drive: 1/2 inch square-end DIN 3121 shape G 12,5, Output: Allen DIN 475/2.


51626short


10 38 17,0 25 8,0 20311 38 18,5 25 9,0 20412 38 19,5 25 9,0 20513 38 21,0 25 10,0 20614 38 22,0 25 10,0 20715 38 23,5 30 10,0 20816 38 25,03 30 11,0 20917 38 26,0 30 12,0 21018 38 27,0 30 13,0 21219 38 28,0 30 13,0 21321 38 31,0 30 13,0 21622 38 32,5 30 13,0 21724 45 35,0 30 14,0 21927 50 39,0 30 16,0 220

long typeSize L D1 D2 T 51626 …mm mm mm mm mm

10 78 17,5 25 12,0 10313 78 21,0 25 12,0 10614 78 22,5 25 12,0 10715 78 23,5 30 12,0 10816 78 25,0 30 12,0 10917 78 26,0 30 13,0 11018 78 27,5 30 13,0 11219 78 28,7 30 13,0 11321 78 30,0 30 13,0 11622 78 32,0 30 13,0 11724 78 35,0 30 20,0 11927 78 38,5 30 24,0 120

Hexagon servo screwdriver bits 51629

Type Drive: 1/2 inch square-end DIN 3121 shape G 12,5, Output: outer hexagon DIN/ISO 2963.



5 55 25 1016 55 25 1028 55 25 103

10 55 25 104


12 55 25 10514 55 25 10617 55 25 107

51629

eng/OP

• Impact tools

Outer TORX® servo screwdriver bits

TypeDrive: 1/2 inch square-end DIN 3121 shape G 12,5, Output: E profile for outer TORX® screws.



51635

51635

Size L D1 D2 T 51635 …E mm mm mm mm

10 38 15,0 25 7,0 10112 38 16,0 25 8,0 10214 38 18,5 25 9,0 10316 38 20,0 25 10,0 104

Size L D1 D2 T 51635 …E mm mm mm mm

18 38 22,0 25 11,0 10520 38 25,0 30 12,0 10624 38 28,5 30 14,0 107

51638 501-502

Servo screwdriver bit accessories51638


Ball joint 1/2 1/2 30 74 - 201Extension 1/2 1/2 25 75 - 301Extension 1/2 1/2 25 125 - 302Extension 1/2 1/2 25 250 - 304Bit holder 1/2 D 6,3 25 38 - 401Bit holder 1/2 D 8 25 35 - 402

Adapter 1/2 3/8 25 38 - 403Adapter 1/2 3/4 30 48 - 404

Rubber ring – – 25 – 10 pcs. 501Rubber ring – – 30 – 10 pcs. 502

Safety pin – – 25 – 10 pcs. 601Safety pin – – 30 – 10 pcs. 602

51638 201

51638 301-304

51638 401-402

51638 403-404

51638 601-602

Servo screwdriver connecting piece51639

TypeWith quick-change toolholder,Drive: 1/2 inch square-end, DIN 3121 shape G 12,5, Output: outer square, DIN 3121 - with ball lock.



1/2 1/2 25 60 44 24 101


51638 201-304 Type Drive: 1/2 inch square-end, DIN 3121 shape G 12,5, Output: outer square, DIN 3121 shape E - withspring-loaded pin.

51638 401 Type Drive: 1/2 inch square-end, DIN 3121 shape G 10, Output: 1/4 inch Allen DIN 3126 shape D 6,3.

51638 402 Type Drive: 1/2 inch square-end, DIN 3121 shape G 10, Output: 5/16inch Allen DIN 3126 shape D 8.

51638 403-404 Type Drive: 1/2 inch square-end, DIN 3121 shape G 12,5, Output: outer square, DIN 3121 shape E - withspring-loaded pin.


Short chucks by ATORN:

ATORN‘s high-quality clamping tools.


in the catalogue. Purchase orders must be in units.www.hhw.de51.62

5

ß Hand tools



Type Drive: 3/4 inch square-end DIN 3121 shape H 20, Output: Allen DIN 475/2.


shortSize L D1 D2 T 51641 …mm mm mm mm mm

17 50 31,0 44 12 20218 50 32,0 44 12 20319 50 33,0 44 14 20422 50 37,0 44 16 20724 50 39,0 44 16 20927 54 43,0 44 16 21230 54 47,0 44 23 21532 56 49,0 44 23 21633 56 51,0 44 23 21734 56 52,0 44 23 21836 56 54,0 44 23 22038 58 57,0 44 24 22141 58 60,0 44 24 22346 63 67,0 44 27 224

longSize L D1 D2 T 51643 …mm mm mm mm mm

17 95 31 44 20 10218 95 32 44 20 10319 95 33 44 23 10422 95 37 44 23 10724 95 39 44 51 10927 95 43 44 62 11230 95 47 44 62 11532 95 49 44 62 11633 95 51 44 62 11734 95 52 44 62 11836 95 54 44 62 120

51643

51641 - 51643 3 4


Type Drive: 3/4 inch square-end DIN 3121 shape H 20, Output: outer hexagons DIN/ISO 2963.



14 62 44 10117 62 44 10219 62 44 103


22 62 44 10424 62 44 10527 62 44 106

51644


Type Drive: 3/4 inch square-end, DIN 3121 shape H 20, Output: outer square, DIN 3121 shape F - withthrough-hole for pin.


51646


Ball joint 3/4 3/4 44 90 – 201Extension 3/4 3/4 44 175 – 301Extension 3/4 3/4 44 250 – 302Extension 3/4 3/4 44 330 – 303

Adapter 3/4 1/2 44 57 – 401Adapter 3/4 1 44 63 – 403

Rubber ring – – 44 – 10 pcs. 501Safety pin – – 44 – 10 pcs. 601

51646 201

51646 301-303

51646 401-403

51646 601

3 4


TypeWith quick-change toolholder.Drive: 3/4 inch square-end DIN 3121 shape H 20,Output: outer square DIN 3121 - with ball lock.



3/4 3/4 44 78 55 29 101

51647 3 4

3 4

51646 501



5

eng/OP

• Impact tools • Socket Keys

www.hhw.de51.64

5


Type Drive: 1 inch square-end DIN 3121 shape H 25, Output: Allen DIN 475/2.


shortSize L D1 D2 T 51649 …mm mm mm mm mm

22 58 40 54 17 10324 58 42 54 17 10527 58 46 54 17 10630 60 50 54 21 10932 60 52 54 21 11033 60 53 54 21 11134 62 55 54 21 11236 65 56 54 30 11338 65 59 54 30 11441 67 63 54 31 11646 74 69,5 54 36 11850 80 74 54 42 11955 84 81 54 44 12060 87 87 54 44 12165 90 93 54 46 12270 96 100 54 51 12375 98 104 86 52 12480 100 109 86 52 125

51649 - 51651

51649

long typeSize L D1 D2 T 51651 …mm mm mm mm mm

22 100 40 54 21 10324 100 42 54 21 10527 100 46 54 23 10630 100 50 54 50 10932 100 52 54 50 11033 100 53 54 50 11134 100 55 54 50 11236 100 57 54 64 11338 100 59,5 54 64 11441 100 64 54 64 11646 100 69,5 54 62 118

51651


Type Drive: 1 inch square-end, DIN 3121 shape H 25, Output: outer square, DIN 3121 shape F - withthrough-hole for pin.

QualityChrome-vanadium special steel. 51652 101


Ball joint 1 1 54 110 - 101Extension 1 1 54 175 - 201Extension 1 1 54 250 - 202Extension 1 1 54 330 - 203

Adapter 1 3/4 54 75 - 301Rubber ring - - 54 – 10 pcs. 401

Safety pin - - 54 – 10 pcs. 501

51652 201-203

51652 301

51652 401 51652 501

51652


TypeWith quick-change toolholder.Drive: 1 inch square-end DIN 3121 shape H 25,output: outer square DIN 3121 - with ball lock.



1 1 54 96 68 40 101

51653

Special tools and custom products

SALTUS®, certified company, develops and manufactures, besides their vastrange of standard tools, also customised non-standard and special tools forits clients.

Manufacture follows international standards, samples or diagrams. Be itsingle-part production or serial production - all SALTUS® products stand outfor their extremely narrow tolerances, long service life and durability.

Z

PRECISION MEETS TECHNOLOGY



ß Hand tools


5

Sets of hexagon wrenches ISO 293651805

0Quality59 chrome-molybdenum-vanadium 4, nickel-plated.

51805 10151805 103 51805 104

51805 102

51805 106Number of Size 51805 …wrenches Type mm

6 in plastic pouch 2 / 2,5 / 3 / 4 / 5 / 6 1018 in plastic pouch 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 1028 on key ring 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 1038 in plastic sliding box 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 104

10 in plastic pouch 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 / 12 / 14 106

Hexagon wrenches ISO 293651808 - 51809

51808black.QualityTool steel C 60 /C45.

51809

0Nickel-plated.Quality59 chrome-molybdenum-vanadium 4.

51809

black nickel-platedSize Leg length 51808 … 51809 …mm mm0,7 33 x 7 101 0,9 33 x 11 1021,3 40 x 12 103 1031,5 46,5 x 15,5 104 104

2 52 x 18 105 1052,5 58,5 x 20,5 106 106

3 66 x 23 107 1073,5 69,5 x 25,5 108 108

4 74 x 29 109 1095 85 x 33 111 1116 96 x 38 113 1137 102 x 41 114 1148 108 x 44 115 115

black nickel-platedSize Leg length 51808 … 51809 …mm mm

9 114 x 47 116 11610 122 x 50 117 11711 129 x 53 118 11812 137 x 57 119 11914 154 x 70 120 12017 177 x 80 121 12119 199 x 89 122 12222 222 x 102 123 12324 248 x 114 124 12427 277 x 127 125 12530 315 x 142 12632 347 x 157 127 12736 391 x 176 128

Hexagon wrenches ISO 2936

mQualityChrome-vanadium, hardened and nickel-plated.

51811 101-102 In impact-proof plastic sliding box.

51811 103 In stand made of impact-proof plastics. Withconnector for further stands.

51811 101

SetNumber of Size 51811 …

Wrench mm7 2 / 2,5 / 3 / 4 / 5 / 6 / 8 1018 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 1029 2,5 / 3 / 4 / 5 / 6 / 8 / 10 / 12 / 14 103

51811 103

51812

51811 102

51811 - 51812

Single wrenchesSize Leg length 51812 …mm mm 1,5 46,5 x 15,5 102

2 52 x 18 1032,5 58,5 x 20,5 104

3 66 x 23 1054 74 x 29 106

Size Leg length 51812 …mm mm

5 85 x 33 1076 96 x 38 1087 102 x 41 1098 108 x 44 1109 114 x 47 111


10 122 x 50 11212 137 x 57 11414 154 x 70 11517 177 x 80 11619 199 x 89 117

eng/OP

• Socket Keys

www.hhw.de51.66

5


sTypeHex-Plus system, chrome-plated.

51817In plastic clip.

Note:The Hex-Plus system provides a 5-x larger contactsurface when compared to standard Allen keysystems. This increases the service life of tool andscrew, reduces the wedge effect and increasestorque. Therefore, larger numbers of operations arepossible.

51817

51818Set

Number of Size 51817 …Wrench mm

9 1,5 / 2,0 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 103


,QualityVanadium-extra steel, nickel-plated and chrome-plated.

Note:Up to size 3 mm burnished.

51823In plastic pouch.


Wrench mm7 2 / 3 / 4 / 5 / 6 / 7 / 8 101

11 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 10215 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 14 / 16 / 17 / 19 103

Single wrenchesSize Leg length 51824 …mm mm1,5 46,5 x 15,5 101

2 52 x 18 1022,5 58,5 x 20,5 103

3 66 x 23 1044 74 x 29 1065 85 x 33 108


6 96 x 38 1097 102 x 41 1108 108 x 44 1119 114 x 47 112

10 122 x 50 11311 129 x 53 114


12 157 x 57 11514 154 x 70 11617 177 x 80 11719 199 x 89 118

51823

51824

Set of hexagon wrenches similar to ISO 2936

0Quality59 chrome-molybdenum-vanadium 4.

51829TypeIn folding holder, each hexagon wrench can be setto any angle up to 180°.

51830TypeIn plastic folding handle. With folding support.

51829 101-103

51830 101-103 51830 106

51829 - 51830

Unit of measurement Number of Sizes 51829 … 51830 …wrenches

J Allen key mm 7 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 101 101J Allen key mm 7 2,5 / 3 / 4 / 5 / 6 / 8 / 10 103 103JV Allen key with ball head mm 7 2,5 / 3 / 4 / 5 / 6 / 8 / 10 106G TORX® T 8 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 107 107GV TORX® with ball head T 8 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 108

Single wrenchesSize Leg length 51818 …mm mm1,5 45 x 14 101

2 50 x 16 1022,5 56 x 18 103

3 63 x 20 1044 70 x 25 105


5 80 x 28 1066 90 x 32 1078 100 x 36 108

10 112 x 40 10911 120 x 43 110


12 125 x 40 11113 132 x 50 11214 140 x 56 11317 160 x 63 11419 180 x 70 115

ß Hand tools


5

Biketool51832

mType16-part, pocket-sized. Blades hardened andburnished. Housing made of 2-component plastics.ApplicationThe perfect tool for bicycle trips.

51832

Set contentsJ 7 Allen keys

size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm,D 1 Phillips screwdriver PH 2,Q 1 screwdriver 0,8 x 5,N 3 socket wrench bits 8 / 9 / 10 mm,

3 single open-end wrench 8 / 10 / 15 mm,1 spoke wrench 14 Acc.

H x W x D Weight 51832 …mm g

90 x 50 x 32 260 101

Set of hexagon wrenches (combination)51834

+-Pocket-Star- Type Hexagon wrench holder with ejection button for easychoice of wrench. Housing made of fibre-reinforcedplastic.

51834 098Set contents 7-part:J for Allen screws

size 2 / 2,5 / 3 / 4 / 5 / 6 / 8 mm.

51834 099Set contents 8-part:C for inner TORX® screws with pilot

T9 / 10 / 15 / 20 / 25 / 27 / 30 / 40.

51834 102Set contents 9-part: Q for slotted screws 4,5 mm, D for Phillips recess head screws PH 2, J for Allen screws

size 3 / 4 / 5 / 6 mm, M for TORX® screws T10 / 15 / 20.

51834 102

51834 098

51834 099

Type Number of 51834 …wrenches

Hexagonal 7 098TORX® with borehole 8 099

For slotted screws / Phillips / hexagonal / TORX® 9 102

Set of hexagon wrenches (combination)51835

+Type: Mini-Pocket-TypeHexagon wrench holder with ejection button for easychoice of wrench. Housing made of fibre-reinforcedplastic. Hang-up hole with carabiner.

51835 101Set contents 8-part:Q for slotted screws 1,5 / 2 mm,D for Phillips recess head screws PH 00,J for Allen screws

size 0,7 / 0,9 / 1,3 / 1,5 / 2 mm.

51835 102Set contents 8-part:Q for slotted screws 1,5 / 2 mm,D for Phillips recess head screws PH 00,J for Allen screws size 2 mm,M for TORX® screws T4 / T5 / T6 / T7.

Number of 51835 …wrenches

8 1018 102

51835 101

51835 102

Hexagon wrenches (imperial) similar to ISO 2936

0Quality59 chrome-molybdenum-vanadium 4, nickel-pla-ted.

51836In plastic sliding box.

51836 - 51837

51836

51837

SetNumber of Size 51836 …wrenches inch

8 5/64 / 3/32 / 1/8 / 5/32 / 3/16 / 1/4 / 5/16 / 3/8 101Single wrenches

Size Size Leg length 51837 …inch mm mm3/64 1,19 41 x 13 1000,05 1,27 41 x 13 1011/16 1,59 47 x 16 1025/64 1,98 52 x 18 1033/32 2,38 58 x 20 1047/64 2,77 66 x 23 121

1/8 3,18 66 x 23 1059/64 3,57 72 x 26 1065/32 3,97 74 x 29 1073/16 4,76 85 x 33 1087/32 5,56 91 x 36 109

Size Size Leg length 51837 …inch mm mm

1/4 6,35 96 x 38 1109/32 7,14 102 x 42 1115/16 7,94 108 x 44 1123/8 9,53 122 x 50 113

7/16 11,11 130 x 53 1141/2 12,70 145 x 63 115

9/16 14,29 154 x 69 1165/8 15,88 176 x 76 1173/4 19,05 199 x 89 1187/8 22,20 222 x 102 119

1. 25,40 275 x 125 120

eng/OP

• Socket Keys

www.hhw.de51.68

5

Hexagon wrenches (inch) ISO 293651842 - 51843

,QualityVanadium-extra steel, nickel-plated and chrome-plated.

Note:Up to size 3/32 burnished.


51842

51843

Single wrenchesSize Size Leg length 51843 …inch mm mm1/16 1,59 47 x 16 1025/64 1,98 52 x 18 1033/32 2,38 58 x 20 1041/8 3,18 66 x 23 105

9/64 3,57 72 x 26 1065/32 3,97 74 x 29 1073/16 4,76 85 x 33 1087/32 5,56 91 x 36 109

Size Size Leg length 51843 …inch mm mm

1/4 6,35 96 x 38 1105/16 7,94 108 x 44 1123/8 9,53 122 x 50 113

7/16 11,11 130 x 53 1141/2 12,70 145 x 63 115

9/16 14,29 154 x 69 1165/8 15,88 176 x 76 117

Sets of long hexagon wrenches ISO 293651848 - 51851

51848

0TypeNickel-plated, extra long.Quality59 chrome-molybdenum-vanadium 4.

51850Typeblack.QualityC60/C45.

51848

51851

51850

Single key black nickel-platedSize Leg length 51850 … 51851 …mm mm1,5 91,5 x 15,5 101 101

2 102 x 18 102 1022,5 114,5 x 20,5 103 103

3 129 x 23 104 1044 144 x 29 105 1055 165 x 33 106 1066 186 x 38 107 107

black nickel-platedSize Leg length 51850 … 51851 …mm mm

8 208 x 44 108 10810 234 x 50 109 10912 262 x 57 110 11014 294 x 70 111 11117 337 x 80 112 11219 379 x 89 113 113

Set nickel-platedNumber of Type Size 51848 …wrenches mm

8 in plastic sliding box 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 101

Sets of long hexagon wrenches ISO 2936

mQualityChrome-vanadium, hardened and nickel-plated.

51854 101 In impact-proof plastic sliding box.

51854 102 In stand made of impact-proof plastics. Withconnector for further stands.

51854 101


Wrench mm8 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 1019 2,5 / 3 / 4 / 5 / 6 / 8 / 10 / 12 / 14 102

Single wrenchesSize Leg length 51855 …mm mm

2 102 x 18 1022,5 114,5 x 20,5 103

3 129 x 23 1044 144 x 29 1055 165 x 33 1066 186 x 38 1077 197 x 41 108


8 208 x 44 10910 234 x 50 11012 262 x 57 11214 294 x 70 11317 337 x 80 11419 379 x 89 115

51854 102

51855

51854 - 51855

SetNumber of Size 51842 …wrenches inch

9 3/64 / 1/16 / 5/64 / 3/32 / 1/8 / 5/32 / 3/16 / 7/32 / 1/4 10114 3/64 / 1/16 / 5/64 / 3/32 / 1/8 / 5/32 / 3/16 / 7/32 / 1/4 / 5/16 / 3/8 / 7/16 / 1/2 / 9/16 104

51851

0TypeNickel-platedQualität59 Chrom-Molybdän-Vanadium 4.

ß Hand tools


5

Sets of long hexagon wrenches ISO 2936

sTypeHex-Plus system, chrome-plated.


Note:Technical information about the Hex-Plus systemsee cat.-no. 51817-51818.

51865

51864

51864 - 51865

Hexagon wrench with handle ISO 2936

ßTypeWith plastic square handle.QualityBlade made of chrome-vanadium steel, full-har-dened, nickel-plated.

51870 202

SetNumber of Type Size 51870 …wrenches mm

6 straight 3 / 4 / 5 / 6 / 8 / 10 2016 offset 3 / 4 / 5 / 6 / 8 / 10 202

Single keys straight offsetSize Overall length straight/ offset 51871 … 51872 …mm mm

2 120 / - 2012,5 150 / - 202

3 150 / 110 x 20 203 2034 160 / 120 x 25 204 2045 170 / 130 x 28 205 2056 205 / 145 x 32 206 2068 205 / 165 x 36 207 207

10 215 / 190 x 40 208 208

51870 201

51870 - 51872


Wrench mm9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 102


Screwdrivers by ATORN:


Single wrenches Size Leg length 51865 …mm mm1,5 90 x 14 101

2 100 x 16 1022,5 112 x 18 103

3 126 x 20 1044 140 x 25 1055 160 x 28 106


6 180 x 32 1077 190 x 30 1088 200 x 36 109

10 219 x 40 11012 250 x 45 111

eng/OP

• Socket Keys

www.hhw.de51.70

5

Hexagon wrench with T-handle

0TypeWith plastic T-handle.Quality59 chrome-molybdenum-vanadium 4, nickel-pla-ted.

51876 - 51877

51876 101

51877


Wrench mm7 2 / 2,5 / 3 / 4 / 5 / 6 / 8 1019 2,5 / 3 / 4 / 5 / 6 / 8 / 10 / 12 / 14 102

Single wrenchesSize Blade length 51877 …mm mm

2 100 1012,5 100 103S 3 50 104

3 100 105L 3 150 106

XL 3 200 1074 100 108

L 4 150 109XL 4 200 110

5 100 111

Size Blade length 51877 …mm mmL 5 150 112

XL 5 200 1136 100 114

L 6 150 115XL 6 200 116

8 100 117L 8 150 118

XL 8 200 11910 100 120

L 10 200 121

Hexagon wrench with T-handle51879 - 51880

+Type Ergonomically-shaped soft zone handle with stubby. Quality Continuous blade chrome-plated, full-hardened.Chrome-vanadium steel.

51880

51879


Wrench mm6 2,5 / 3 / 4 / 5 / 6 / 8 101

Single wrenchesSize Length 51880 …mm mm

2 100 1012,5 100 102

3 100 1034 150 104

Size Length 51880 …mm mm

5 150 1056 150 1068 200 107

10 200 108


JTypePolished phosphated, ergonomic handle. Hexagonim Hex-Plus® profile.ApplicationThanks to the ergonomically-shaped handle, bothends of the keys can be used effectively.


51882

Size Leg length 51882 …mm mm2,5 133 x 63 101

3 133 x 63 1024 183 x 77 1035 183 x 77 1046 240 x 95 1058 240 x 95 106

10 240 x 95 107

Size Leg length 51883 …inch mm5/32 183 x 77 1033/16 183 x 77 1047/32 240 x 95 1051/4 240 x 95 106

5/16 240 x 95 1073/8 240 x 95 108

51882 - 51883

ß Hand tools


5


TypeAllen profile on three ends. 51884 101


Wrench mm8 2 / 2,5 / 3 / 3,5 / 4 / 4,5 / 5 / 6 101


2 125 x 63 2012,5 150 x 63 202

3 150 x 63 2033,5 175 x 76 204

4 175 x 76 2054,5 195 x 87 206

5 195 x 87 207


6 215 x 99 2087 230 x 109 2098 250 x 122 2109 265 x 132 211

10 280 x 142 21212 305 x 160 21314 330 x 178 214

51884

Long hexagon wrenches with ball head similar to ISO 2936L51888 - 51889

0ApplicationFor application on hidden Allen screws up to anangle of 30°.

Quality59 chrome-molybdenum-vanadium 4, nickel-plated.


51888

51889


Wrench mm8 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 101

Single wrenchesSize Leg length 51889 …mm mm1,5 91,5 x 15,5 101

2 102 x 18 1022,5 114,5 x 20,5 103

3 129 x 23 1044 144 x 29 105


5 165 x 33 1066 186 x 38 1078 208 x 44 108

10 234 x 50 10912 262 x 57 110

Set of long hexagon wrenches with ball head51892

0Type9-part, in ergonomically shaped hand grip.

ApplicationFor application on hidden Allen screws up to anangle of 30°.Quality59 chrome-molybdenum-vanadium 4, nickel-plated.

51892


9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 101

Long hexagon wrench with ball head

sTypeHex-Plus system, chrome-plated.ApplicationFor application with hard-to-reach Allen screws up toan angle of 25°.



51895 - 51896

51895 101

51895 102

51896


Wrench mm7 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 1019 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 102


2 100 x 16 1022,5 112 x 18 103

3 126 x 20 1044 140 x 25 105


5 160 x 28 1066 180 x 32 1078 200 x 36 108

10 219 x 40 109

51884 201-214

eng/OP

• Socket Keys

www.hhw.de51.72

5

. Wera StainlessThe tool for better results.

sThe use of stainless steel averts corrosion. Stainless steel needs tools made of stainless steel. This is the only way to prevent corrosioncaused by the abrasion of standard tools.

Set of long hexagon wrenches with ball head, stainless

sType9-part, Hex-Plus system, in clip made of solidrubber.ApplicationFor application on hidden Allen screws up to anangle of 25°.

QualityBlade made of stainless steel.


51897

51897


Wrench mm9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 101

Set of long hexagon wrenches with ball head51899

mTypeThe holder doubles as T-handle.

QualityChrome-vanadium, hardened and nickel-plated.

51899


7 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 101

Long hexagon wrench with ball head

sTypeIn clip made of solid rubber. Ergonomical coating ofthe arms. Very large flex angle in axial direction.Longer service life thanks to special tool steel (bitmaterial). The Hex-Plus system allows up to 35%higher static torque and reduces the harmfulwedge effect in the screw's head by approx.80%.



Wrench mm9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 102


2 101 x 16 2022,5 112 x 19 203

3 123 x 21 2044 137 x 24 205


5 154 x 27 2066 172 x 31 2078 195 x 37 208

10 224 x 42 209

51901

51902

51901 - 51902

ß Hand tools


5

Long hexagon wrench with ball head (MagicRing) ISO 2936L

+TypeStarting at 3 mm, with MagicRing made of springsteel. Set in -ProStar- holder (for easiest removal of anysingle key without moving the others).ApplicationPerfectly secures hexagonal screws in compliancewith DIN 912 in any position thanks to the high-qua-

lity spring steel ring. For example for insertingscrews into blind holes of any angle or depth.Magnetising of the wrench tip is no longer required!For application up to an angle of 25°. New design:increased holding power, 10 % higher torque.QualityChrome-vanadium steel, full-hardened, chrome-plated.

51907

SetNumber of Size 51907 …wrenches mm

9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 201


3 128 x 23 2044 142 x 29 2055 163 x 33 206


6 184 x 38 2078 206 x 44 208

10 231 x 50 209

51908

51907 - 51908

Hexagon wrench with ball head with T-handle51911 - 51912

0TypeWith ergonomic T-handle.

QualityChrome-vanadium steel, nickel-plated.

Note: Sizes 2,5 and 3 mm without ball head.

51911

51912


7 2 / 2,5 / 3 / 4 / 5 / 6 / 8 101

Single wrenchesSize Blade length 51912 …mm mm

3 100 1014 100 102

L 4 150 1035 100 104

L 5 150 105

Size Blade length 51912 …mm mm

6 150 106L 6 200 107

8 150 108L 8 200 10910 200 110

Hexagon wrench with ball head with T-handle

ßTypeWith rubber-coated T-handle for maximum load.ApplicationFor application on hidden Allen screws up to anangle of 25°.

QualityBlade special hardened.

51913 - 51914

51913


Wrench mm5 4 / 5 / 6 / 8 / 10 101

Single wrenchesSize Overall length 51914 …mm mm

4 200 1015 225 1026 240 1038 260 104

10 280 105

Number of Size 51905 …wrenches mm

9 1,5 / 2 / 2,5 / 3 / 4 / 5 / 6 / 8 / 10 101

Set of long hexagon wrenches with ball head similar to ISO 2936L51905

+Type- Higher force thanks to new ball head design.- Lasered-in sizes for easy recognition.- Space-saving holder, mechanical operation for

simplest removal of wrenches without moving others.- Fixed attachment point for mounting the wrenches

in the holder.- Innovative clamping for a secure hold of the

wrenches, in opened and closed holder.

ApplicationNew ball head design for working in hard-to-reachplaces, at an angle of up to 30°.QualityChrome-vanadium steel, full-hardened, chromefinish.

51905

eng/OP

• Socket Keys

www.hhw.de51.74

5

Sets of TORX® wrenches51924

0QualityChrome-vanadium steel (59 Cr-Mo-V4), steel-grey.


51924 101TypeWith hole for TORX® screws with locking pin.

51924 102TypeExtra long, without borehole.

51924 10151924 102

Number of Size 51924 …wrenches T

8 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 10113 5 / 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 / 50 102

TORX® wrenches

0Quality59 chrome-molybdenum-vanadium 4, steel grey.



51925 - 51926

51925

51926

SetNumber of Size 51925 …wrenches T

8 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 201

Single wrenchesSize Leg length 51926 …

T mm6 44,5 x 18,5 2017 50,5 x 18,5 2028 51 x 19 2039 51 x 19 204

10 54 x 20 20515 57,5 x 21,5 20620 61 x 23 20725 64,5 x 24,5 208

Size Leg length 51926 …T mm

27 69,5 x 26,5 20930 76 x 30 21140 83 x 33 21145 91 x 37 21250 104 x 41 21355 120 x 47 21460 134 x 52 215

TORX® wrench set with holding device

sType9-part, in clip made of solid rubber.ApplicationInner TORX® screws in compliance with specificati-on Camcar Textron. TORX®with holding device.The tools are pressed into the drive profile of thescrew manufactured in compliance CAMCARTEXTRON specifications by means of: the drivershoulders (conical in respect to the tool tip), theadditional optimisation of the shoulder area and inconjunction with the perfect insertion depth.

QualityBlade BlackLaser.


51923


9 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 101

51923

Hexagon wrench with ball head with T-handle

JTypePolished phosphated, ergonomic handle. Hexagonin Hex-Plus® profile.ApplicationThanks to the ergonomically-shaped handle, bothends of the keys can be used effectively.

Note:Technical information about the Hex-Plus systemsee cat.-no. 51817-51818. 51919


5 4 / 5 / 6 / 7 / 8 101


4 183 x 77 1035 183 x 77 1046 240 x 95 1058 240 x 95 106

10 240 x 95 107

51919 - 51920

ß Hand tools


5

Set of TORX® wrenches (MagicSpring)

+TypeIn holder. MagicSpring made of stainless steelretains TORX® screws in any position. QualitySurface manganese-phosphated, chrome-vana-dium steel, hardened.


51927

51927

The holding spring islaser-welded to the tipof the tool in conjunctionwith a covering disc.

The MagicSpringgenerates a clampingbetween the tool andthe TORX® or TORXPLUS® screw, so thatthe screw is held safely.


13 5 / 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 / 50 102

Set of TORX® wrenches51928

+Type 13-part, in -ProStar holder (for easiest removal ofany single key without moving the others). Quality Surface manganese-phosphated.

Note: TORX® selector see cat.-no. 37930. 51928


13 5 / 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 / 50 101

Set of ResisTORX® wrenches

JType In compact, foldable holder, easy removal of thekeys.


51929

Number of Size 51929 …wrenches TX

6 10 / 15 / 20 / 25 / 30 / 40 101

51929

TORX® wrenches with T-Handle

0TypeWith plastic T-handle short and long type.

QualityChrome-vanadium steel (59 Cr-Mo-V4), chrome-plated, with black tip.


51931

Size Blade length 51931 …T mm8 100 1019 100 103

10 100 10515 100 107

L 15 200 10820 100 109

L 20 200 11025 100 111

L 25 200 11227 100 113

L 27 200 114

Size Blade length 51931 …T mm

30 100 115L 30 200 116

40 100 117L 40 200 118

45 150 119L 45 250 120

50 150 121L 50 250 122

55 150 12360 150 125

51931

eng/OPwww.hhw.de51.76

TORX® wrenches with T-handle51937

51937

Size Leg Length 51937 …T mm6 133 x 63 1017 133 x 63 1028 133 x 63 1039 133 x 63 104

10 133 x 63 10515 133 x 63 10620 183 x 77 107

Size Leg Length 51937 …T mm

25 183 x 77 10827 183 x 77 10930 240 x 95 11040 240 x 95 11145 240 x 95 11250 240 x 95 113

JTypePolished phosphated, ergonomic handle.


TORX® / TORX PLUS® wrench51932

51932 101

51932 201-208 51932 401-408

0QualityChrome-vanadium steel.


51932 101TypeTORX® profile, blade burnished. 7-part set inworkbench toolholder.

51932 201-208TypeTORX® profile, blade burnished. Single wrench.

51932 301TypeTORX PLUS® profile, blade burnished. 7-part set inworkbench toolholder.

51932 401-408TypeTORX PLUS® profile, blade burnished. Singlewrench.

Single wrench TORX® TORX PLUS®

Size Blade length Blade Ø Handle 51932 … 51932 …T / IP mm mm mm

5 33 2,5 19 201 4016 33 2,5 19 202 4027 33 2,5 19 203 4038 33 2,5 19 204 4049 37 3,0 24 205 405

10 37 3,0 24 206 40615 43 4,0 28 207 40720 43 4,0 28 208 408

SetProfile Number of Size 51932 …

wrenches T / IPTORX® 7 6 / 7 / 8 / 9 / 10 / 15 / 20 101

TORX PLUS® 7 6 / 7 / 8 / 9 / 10 / 15 / 20 301

• Socket Keys

5


Solid carbide high-performance twist drills by ATORN:

ATORN‘s high-quality drilling tools.

ß Hand tools


ResisTORX® wrenches

sTypeWith hole, which allows the application on TORX®

screws and on TORX® safety screws (with pilot pin).Ergonomical coating of the arms. Very largeswivelling range in axial direction, increased servicelife thanks to special tool steel (bit material).

Note:T8 and T9 without boreholes and ball head, T10without ball head. TORX® selector see cat.-no.37930.

51954TypeIn plastic clip with magnetiser, to effortlessly insertscrews in deep housings or boreholes. The magne-tic insert helper even works perfectly with screwdri-vers!

51954 - 51955

51954

magnetising demagnetising

51955


9 8 / 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 101


T mm9 79 x 16 101

10 85 x 17 10215 90 x 18 10320 96 x 19 10425 104 x 21 105


27 112 x 22 10630 122 x 24 10740 132 x 27 10845 143 x 29 10950 156 x 32 110

TORX® wrenches with ball head

51942


8 9 / 10 / 15 / 20 / 25 / 27 / 30 / 40 101


T mm9 67 x 19 101

10 76 x 20 10215 86,5 x 20,5 10320 98 x 22 10425 100,5 x 22,5 10527 111,5 x 25,5 106


30 125 x 30 10740 139 x 33 10845 145 x 37 10950 149 x 41 11055 157 x 47 111

51943

51942 - 51943

TORX® wrenches with T-handle

+Type Ergonomically-shaped soft zone handle with stubby.

Quality Continuous blade chrome-plated, full-hardened.Chrome-vanadium steel.


51938


6 10 / 15 / 20 / 25 / 30 / 40 101

Single wrenchesSize Blade length 51939 …

T mm10 100 10115 100 10220 100 10325 150 104

Size Blade length 51939 …T mm

27 150 10530 150 10640 150 107

51939

51938 - 51939

0ApplicationFor application on hidden TORX® screws up to anangle of 20°.QualityBlade made of alloyed steel, specially hardened,steel grey.


51942In plastic holder.

5

eng/OP

• Socket Keys • Screw Extractors • Thread Recutter

www.hhw.de51.78

5

Hexagon wrench with pilot DIN 6911

0ApplicationFor Allen screws DIN 6912.

Quality59 chrome-molybdenum-vanadium 4, nickel-plated.


51960


5 3 / 4 / 5 / 6 / 8 101

Single wrenchesSize Leg length Pilot Ø Pilot length 51961 …mm mm mm mm

3 66 x 23 2,0 1,1 1014 74 x 29 2,5 1,3 1025 85 x 33 3,0 1,6 1036 96 x 38 4,0 2,6 1048 108 x 44 5,0 2,8 105

Size Leg length Pilot Ø Pilot length 51961 …mm mm mm mm

10 122 x 50 6,0 3,2 10612 137 x 57 7,0 3,5 10714 154 x 70 8,0 3,6 10817 177 x 80 10,0 4,5 109

51960 - 51961

Trisquare keys DIN 65253

0TypeNickel-plated.

ApplicationFor XZN Trisquare screws.QualityChrome-vanadium steel.

51966

For Leg length 51966 …screws mm

M 5 75 x 30 102M 6 86 x 34 103M 8 98 x 40 104

M 10 110 x 46 105


M 12 124 x 52 106M 14 139 x 59 107M 16 156 x 72 108

51966

Spline keys

TypeNickel-plated.ApplicationFor spline screws RIBE CV.


51971


M 4 67 x 24 101M 5 75 x 30 102M 6 86 x 34 103M 8 98 x 40 104


M 10 110 x 46 105M 12 124 x 52 106M 14 139 x 59 107M 16 156 x 72 108

Screw extractors, two cutting blades

ßTypeNon-slip insertion by two cutting blades into thescrew or stud bolt. With lathe centre. Surfaceburnished, cutting blades polished.ApplicationFor non-damaging extracting of broken-off screws orstud bolts from threaded holes. For right-hand andleft-hand threads. In order to ensure a safe grip ofthe extractor, it is hammered into the borehole..

QualityChrome-vanadium steel, hardened.

51985TypeSet 5-part, in metal box.

51986TypeSingle, in plastic box.

51985

SetNumber of Set contents 51985 …Extractors size

5 1 - 5 101

singleSize Size Borehole Ø Borehole Ø Screw size Screw size 51986 …

mm min. mm max. mm min. max.1 6,35 3,2 4,8 M 5 M 6 1012 9,50 4,8 7,1 M 8 M 10 1023 12,70 6,4 9,5 M 10 M 12 1034 15,90 8,7 12,7 M 12 M 16 1045 19,00 11,1 15,9 M 16 M 20 1056 22,00 14,3 19,1 M 20 M 24 1067 25,40 19,1 23,8 - M 30 107

51986

51985 - 51986

ß Hand tools


5

Screw extractors

&TypeRolled thread, ground shank. Set in plastic box.ApplicationMaximum torque in Nm at a test element with amaterial tension of 1147 N/mm2 and a hardness of35 HRc. For extracting broken-off screws with right-hand thread and broken-off pipe ends from fittings.Quality59 chrome-vanadium steel, hardened, 54-56HRc.

51991Screw extractors HITRACTypeAdditionally with milled groove.Due to theimproved design and thread length considerablyless power is required for extracting.Available in two different set sizes.

51990 101

Set HITRACNumber of Set contents 51990 … 51991 …Extractors size

5 1 - 5 100 1006 1 - 6 101 1018 1 - 8 102

singleSize Ø Tip Ø Shank Overall length Recommended For 51992 …

mm mm mm drill Ø mm screws1 1,4 3,6 50 1,8 M 3 - 4 1012 2,1 4,9 57 3,2 M 5 - 7 1023 3,1 6,5 64 4,5 M 8 - 10 1034 4,8 8,8 71 6,5 M 11 - 14 1045 6,2 11,0 79 8,5 M 16 - 18 1056 9,4 15,0 85 11,8 M 18 - 24 1067 12,7 19,0 92 15,3 M 24 - 33 1078 17,5 24,0 100 20,0 M 33 - 45 108

51991 100

51990 102

51991 101

51990 - 51992

Multi-purpose thread recutter

VTypeQuick fixation by means of adjustment screw.Automatic adjustment of the blade to any threadpitches.ApplicationFor recutting of right-hand and left-hand threads. Forall metric and non-metric types of threads (60° flankangle).

51995 10151995 103

For thread Ø For thread Ø 51995 …mm inch

4 - 13 5/32 - 1/2 10116 - 38 5/8 - 1.1/2 103

51995

Nut splitters and stud inserters and extractors see cat.-no. 78010 – 78030

51992

eng/OP

• Screwdriver

www.hhw.de51.80

5

Hold on tight...Screwdriver made by ß

ß

Routine-tested incompliance with VDE0680/T201, IEC 900,standard DIN 7437.Blade burnished,insulated. Black-Point-tip. Kraft-form handle withroll stop.

sBlade made of high-alloyedspecial steel, nicromatt,output Lasertip Black-Point-tip.Ergonomically optimisedKraftform-handlemade of 3-component-material with integra-ted soft zones forperfect torquetransmission,handle with rollstop.

sNote:Kraftform screwdriver with Lasertip bladeBetter results thanks tohigher safetyhigher power transmissionhigher speed

+Blade made of high-quality chrome-vanadium-molybdenum steel, full-hardened, glossy nickel-plated.ChromTop-tip.Robust square-handle made ofimpact-proof plastics, chemicalsand oil-resistant.

sRoutine-tested, DIN 7437, IEC 60900:2004.

sThe chisel-screwdriverWith impact plate and full-length blade.Highly ductile. Blade made of high-alloy-ed special steel, nicromatt, starting at0,8 x 4,5 with hexagonal shoulder ontang for using a wrench. OutputBlack-Point tip. Ergonomicallyoptimised Kraftform-handle madeof 3-component material withintegrated soft zones for besttorque transmission, handle withroll stop.

,Blade made of vanadium-extrasteel, with matt-chrome finish, full-hardened, tip burnished. Ergono-mic 3-component-handle,impact-proof. Permanent colourcoding on both handle ends.

+Blade made of high-quality chrome-va-nadium steel, full-hardened, glossynickel-plated. ChromTop-pointed tip.Untreated beechwood-handle,elaborately sealed. Robust leathercap provides protection for the top ofthe handle. Starting at 5,5 mm withfull-length blade, hexagonalshoulder on tang for using awrench and blade with slipprotection.

+Blade made of high-quality chrome-vanadium-molybdenum steel, full-hardened, burnished. ErgonomicSoftFinish® handle for highesttorque transmission, with rollstop. routine-tested, DIN EN60900 (IEC 900).

+Blade made of high-qualitychrome-vanadium-molybdenumsteel, full-hardened, matt-chromefinish. ChromTop-pointed tip.Ergonomic SoftFinish® handlefor highest torque transmission,with roll stop.

sBlade made of high-alloyed special steel.Black-Point-tip. Ergonomically optimisedKraftform-handle with roll stop. Forworking on electronic construction partsprone to electrostatic charges. Fulfilsthe standard EN 100-015 part 1.Note:Due to the electrically conductingcharacteristics of the ESD/EGBhandle, these tools must not touchlife wires or parts. Damages due toelectrical shock may becaus- edshould this be the case.

,

Individually tested, DIN EN 60900(IEC 900). Blade made of vanadium-extra steel, with matt-chrome finish,full-hardened, tip burnished.Ergonomic 3-component-hand-le, impact-proof. Permanentcolour coding on both handleends.

ßBlade made of high-alloyspecial vanadium steel,hardened, with Nicromatt-surface, non-dazzle andnon-peeling. Black-Point-tip. Kraftform-handle with roll stop.

0Blade made of chrome-vanadium-molybdenum steel, full-hardened,blackened tip, hexagonal shoulderon tang for using a wrench. Multi-component handle with extra large soft zone and attachmenteye.

Date post:	18-Jan-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Safety advantage 1 · STAHLWILLE QuickRelease-System STAHLWILLE AS-Drive Safety advantage 1 Safety...

Documents