3

1

8

Pipe cutters, Hammers,Chisels, Files, Miscellaneous tools

Guide rolls for pipe cutters

Additional rings for versions withthree cutting wheels

Cutting wheels forsteel, non-ferrousmetal and plasticpipes

Pin for wheels and rolls

Individual components

2

4

3

Original STAHLWILLE pipe and tube tools

These extremely robust pipe cutters guarantee accurate cutting without thedanger of the cut running off at an angle. Pipes can be directly passed on tothe next processing stage.

Cutting wheels for cast pipes

Cutting wheels for steel tubes

2

4

31

1

Essential product advantages when cutting pipes withSTAHLWILLE pipe cutters:

Straight-line cuttingSTAHLWILLE EXPRESS pipe cutters ensure a perfectlyperpendicular cut. The broad support rolls ensure thatthe cutting wheels are accurately guided throughout thecut. In this way, the cut cannot run off at an angle onthe pipe surface or enter the pipe at a tilted angle.The robust drop forged upper-jaw section with itsreinforced cutter-wheel guides prevents spiral cuts.

Deburring and chamferingThe wide guide rolls flatten the burr created during the cutting process back into the material. Separate deburring is not required. The cut-to-length pipe is automatically chamfered and can be passed directly to the next processing step. The cut edge is angled in accordance with the cutting wheel geometry.

Universally applicable –Work on pipes in situ

STAHLWILLE EXPRESS pipe cutters can also be equipped with three cutting wheels. This enables extremely efficient work on pipes in situ involving only a small angle of movement.

STAHLWILLE cutting wheels for steel and cast pipes

Especially high-grade, wear-resistant steel enables extraordinarily high cutting force. The cutting wheels are made of very tough special steel which guarantees long service lifetimes.

EXPRESS Pipe Cutter No 150Ideal for pipes made of steel, copper, brass, light alloy andhard plastics. This tool is available in four sizes to coverouter diameters from 6 to 115 mm.

238

METAL Pipe Cutter No 153This light-weight, extremely convenient tool is speciallysuitable for cutting tubes made of copper, brass, lightalloy or hard plastics and for thin-walled steel tubeswith outer diameters of from 3 to 35 mm and maxi-mum cutting depths of 2.5 mm. The integrated internalthree-bladed cutter in the handle removes burrs.

Chain Pipe Cutter No 157Special pipe cutter, infinitely variable, with rotating handle,also for cutting stainless steel pipes with wall thicknesses of up to 1.8 mm and outer diameters of from 25 to 75 mm. Chain lengths up to 270 mm.

Midget tube cutter No 155For pipes and tubes made of copper, brass, light alloy,hard plastics and for thin-walled steel tubes with outerdiameters of from 3 to 16 mm where the maximumcutting depth is 2.0 mm – we recommend this extremelycompact and accurate tube cutter.

Various DIN standardsingle and double flares – easily andquickly produced usingthe STAHLWILLE double flaring tool.

STAHLWILLE Double Flaring Tools No 165Double Flaring Tools are used for making permanent connections between pressurised pipes. DIN standard double flares in accordance with DIN 74234 can be made with this convenient easy-to-use and tough tool made by STAHLWILLE to create safe connections (e.g. in car brake leads) without the need for special skills. Simply clamp the tool in the vice – and it is ready for use. This tool guarantees rapid, safe processing of seamless drawn and double-walled rolled pipes (Bundy®) with wall thicknesses of 0.7 or 1.0 mm with a single flaring bit. Included in the set:

six flaring bits and twoclamping blocks (also available separately)

STAHLWILLE flaring tools –simple to use and guaranteed optimum results.

Single flaring cone D

Double flaringcone E

Double flaringcone F

Double flaring cone F 180°

239

8

240

EXPRESS pipe cutters150with one cutting wheel andtwo guide rollers; for steel,copper, brass, aluminium and hard plastic tubes.

'

F F G Cutting depth RCode size " mm mm max. mm g S €'

60020001 1 1) 1/8–1 1/4 3–32 6–43 4.5 1220 1 106.0060070002 2 1) 1/8–2 3–50 10–63 7 2191 1 105.0060020003 3* 3/4–3 20–80 26–90 9 3153 1 206.0060020004 4 1 1/4–4 32–100 42–115 10 4540 1 255.001

60120001 1/3 2) 1/8–1 1/4 3–32 6–43 4.5 1140 1 120.0060120002 2/3 2) 1/8–2 3–50 10–63 7 2004 1 120.0060120004 4/3 2) 1 1/4–4 32–100 42–115 10 4164 1 284.00'

1) with wide guide rollers2) with three cutting wheels* to be discontinued'

METAL pipe cutter153for use on copper, brass, light alloy,PVC and thin walled steel tubes,with deburring tool (3 cutting edges)inside handle, forged, chromeplated.'

G G Cutting depth RCode " mm max. mm g S €'

60010000 1/8–1 3/8 3–35 2.5 356 1 62.50'

Small bore pipe cutter155for use on copper, brass, light alloy, PVC and thin walled steel tubes.

'

G G Cutting depth RCode " mm max. mm g S €'

60070001 1/8–5/8 3–16 2 102 1 22.90'

Cutting wheelsSR150for steel pipes.

'

for pipe O b RCode size cutter mm mm g S €'

69020101 1 150/1 25 14 14 10 9.8069020201 2 150/2 32 19 28 10 9.6069020301 3/4 150/3 + 4 41 19 38 10 17.00'

Cutting wheelsSR153

'

for pipe O b RCode cutter mm mm g S €'

69010001 153 20 6 6 10 9.15'

Cutting wheelsSR155'

for pipe O b RCode cutter mm mm g S €'

69110001 155 20 5 5 10 5.70'

Chain pipe cutter157infinitely adjustable, with twisthandle, also suitable for specialsteel pipes up to 1.8 mm wallthickness, chain length 270 mm.

'

G Cutting depth RCode mm max. mm g S €'

60110001 25–75 2 705 1 112.00'

ChainK157'

RCode g S €'

69130001 183 1 80.50'

Guide rollersfor pipe cutters.

'

for pipe O b RCode No cutter mm mm g S €'

69020107 RL 1500/1 150/1 23 21.5 62 2 7.9069070202 RL 1500/2 150–151/2 28 27.5 117 5 8.6569020302 RL 150/3/4150–151/3 + 4 33 19 230 5 9.9069010002 RL 153 153 12 12 10 5 5.75'

Spindlesfor wheels and guide rollers.

'

wheel- roller- for pipe L O RCode No bolt bolt cutter mm mm g S €'

69020104 BL 150/1 x 1) 150/1 29 7.5 20 1 3.4569020103 BZ 1500/1 x 2) 150/1 38.5 7.5 14 10 3.4569070203 BZ 1500/2 x 150–151/2 46 9 23 10 3.4569070204 BL 1500/2 x 150–151/2 38 9 19 10 3.451

69020303 BZ 150/3/4 x x 150–151/3 + 4 36 9 34 10 3.4569020304 BL 150/4N x 3) 150/4 40 9 21 1 3.3069010003 BZ 153 x 153 18.5 4 2 10 3.4569010004 BL 153 x 153 13 4.75 2 10 3.45'

BL = wheel boltBZ = roller bolt1) wheel- and roller bolt for 150/1 until 1985, wheel bolt for 150/1 from19862) roller bolt for 150/1 from 19863) wheel bolt for 150/4 from 2009'

8

241

Spacing washersRI 1500When required to fit pipe cutters No 150/1, 150/2 orNo 150/4 with 3 cutting wheels (to work in confinedspaces) a total of 4 spacing washers is required.Simply exchange the 2 guide rollers for 2 cutting wheelsNo SR150 with 2 spacing washers to each.

'

for pipe O b RCode size cutter mm mm g S €'

68020101 1 150/1 14 3.9 8 6 2.4568020201 2 150/2, 151/2 16 4.45 8 6 2.6068020301 4 150/4 *) 18 9.5 18 1 2.35'

*) For 150/4 from 2009'

Double flaring tool165with Clamping Blocks, Flaring Conesand Forming Cone No 1652.

'

RCode G g S €'

63030000 4.75; 5; 6; 8; 9; 10 mm 3040 1 396.00'

Clamping blocks16501 pair

'

RCode F g S €'

68030001 4.75; 5; 6; 8; 9; 10 mm 100 1 75.50'

Clamping blocks1650 ma1 pair

'

RCode F g S €'

68030002 4.75 = 3/16"; 5; 6 mm; 1/4; 5/16; 3/8" 100 1 75.50'

Flaring cones

'

G RCode No mm g S €'

68040600 1651/6 6 18 1 16.4068040800 1651/8 8 19 1 16.4068040900 1651/9 9 19 1 16.4068041000 1651/10 10 19 1 16.40'

Flaring cones'

G RCode No " g S €'

68540012 1651ma 4.75/5 3/16" 4.75/5 3/16 18 1 17.4068440016 1651a/ 1/4" 1/4 19 1 16.4068440020 1651a/ 5/16" 5/16 19 1 16.4068440024 1651a/ 3/8" 3/8 19 1 16.40'

Forming cone1652Standard

'

RCode g S €'

68050001 19 1 14.60'

Flaring spindle1655for Double Flaring Tool No 165.

'

RCode g S €'

69100002 487 1 81.50'

Clamping screw1656for Double Flaring Tool No 165.

'

RCode g S €'

69100003 100 1 27.30'

D45° side to face spindle. Raise spindle and swivel sideways.Press Forming Cone into quick-change spindle head.

E45° side of Clamping blocks to facespindle. Pre-form with Flaring Cone,finish with Forming Cone.

F45° side of Clamping Blocks to facespindle. Form with Flaring Cone.

F180°By using the 90° sides of ClampingBlock, Flare "F" receives a flat collar.

Double flaring toolThis simple-to-use STAHLWILLE DoubleFlaring Tool will form accurate flares (to DIN 74234) on seamless drawn-and double walled (BUNDY®) tubing.Clamped in a vice, the tool is instantlyready for use. Flaring and PressureCones are quickly changed.

The robust constructionof the tool, plus the shape of FlaringCones, enables single Cone Flaring ontubes of 0.7 or 1.0 mm wall thickness.

Tubing is held horizontally by25 mm wide clamping blocks.This is important when endless tubing isused. A distance pin controls length oftube required for flaring.

8

242

Rubber composition hammers10940DIN 5128, with two plane faces.

'

O L1 L2 RCode mm mm mm g S €'

70140001 55 320 90 317 2 5.1570140002 65 350 115 527 2 6.7070140003 75 350 130 780 2 10.3070140004 90 380 140 1190 2 15.40'

Plastic hammers10955with interchangeable heads ofimpact resisting cellulose acetateand ash handles.

'

O L1 L2 RCode mm mm mm g S €'

70160027 27 265 90 215 6 8.8570160032 32 280 100 325 6 11.7070160035 35 290 105 400 2 14.1070160040 40 320 110 550 2 16.801

70160050 50 340 115 860 2 25.60'

Spare plastic heads10955Rof impact resisting cellulose acetate, these are lightly heated and thentapped into position.

'

O RCode mm g S €'

79040027 27 13 5 1.1079040032 32 21 10 1.6579040035 35 28 10 2.1579040040 40 37 10 2.501

79040050 50 65 10 4.45'

Nylon hammers10956with interchangeable headsof shockproof nylon vestamidand hickory handles.

'

O L1 L2 RCode mm mm mm g S €'

70171027 27 265 90 232 6 14.5070171032 32 280 100 336 6 18.8070171035 35 290 105 413 2 21.9070171040 40 320 110 546 2 26.801

70171050 50 340 115 898 2 40.7070171060 60 380 135 1339 2 54.50'

Spare nylon heads10956Rthese are lightly heated and then tapped into position.

'

O RCode mm g S €'

79050027 27 10 10 2.0579050032 32 17 10 3.0079050035 35 23 10 3.7579050040 40 28 10 4.601

79050050 50 52 10 8.2579050060 60 83 10 11.00'

Plastic hammers10957the hollow head is partially filled withsteel shot which adds to the weight,prevents recoil; with interchangeableheads made of medium-hardpolyurethane and with a hickoryhandle.'

O L1 L2 RCode mm mm mm g S €'

70190025 25 320 108 320 6 35.8070190030 30 350 115 460 6 38.6070190035 35 355 118 580 6 42.2070190040 40 375 125 760 2 49.701

70190050 50 385 135 1250 2 62.0070190060 60 420 165 1900 2 118.00'

Spare plastic heads10957R'

O RCode mm g S €'

79090025 25 14 10 5.3579090030 30 19 10 7.0079090035 35 26 10 8.6079090040 40 38 10 10.501

79090050 50 72 10 15.0079090060 60 118 10 24.70'

Embossing hammer10958aluminium, cylindrical,with hickory handle.

'

O L1 L2 RCode mm mm mm g S €'

70240040 40 340 155 648 2 31.50'

Engineers hammers10960with ash handles, DIN 1041.

'

L1 L2 RCode g mm mm g S €'

70110005 100 260 82 148 6 11.0070110001 200 280 95 254 6 12.1070110004 300 300 105 396 6 14.6070110002 500 320 118 614 6 15.501

70110006 800 350 130 951 2 23.6070110003 1000 360 135 1132 2 25.2070110007 1500 380 145 1615 2 32.5070110008 2000 400 155 2285 2 42.90'

8

243

Engineers hammers10970with ash handles.

'

L1 L2 RCode lb. mm mm g S €'

70120001 1/4 270 67 176 6 15.5070120005 1/2 290 82 320 6 17.5070120006 3/4 310 93 454 6 18.7070120002 1 320 99 575 6 20.001

70120004 1 1/2 350 118 790 2 26.8070120003 2 380 126 1044 2 30.60'

ES 10956/10960/2

175 x 350 x 45 mm, 2 pieces'

RCode g €'

96838125 1130 45.25'

No 10956 O 35 mm'

No 10960 500 g'

83812025 Empty tray 114 7.85'

ES 10956/10970/2

175 x 350 x 45 mm, 2 pieces'

RCode g €'

96838131 1075 49.75'

No 10956 O 35 mm'

No 10970 1 lb.'

83812025 Empty tray 114 7.85'

Ribbed cold chisels100of tough tempered special steel,chrome plated.

'

L b RCode size mm mm g S €'

70010005 5* 125 18 93 10 8.5070010006 6 150 20 165 10 9.9570010008 8 200 26 305 5 14.5070010010 10 250 30 507 5 18.801

70010012 12 300 35 807 5 26.70'

* to be discontinued'

Ribbed cross-cut chisel101*of tough tempered special steel,chrome plated.

'

L b RCode size mm mm g S €'

70030006 6 150 4 143 10 10.30'

* to be discontinued'

Cold chisels102DIN 6453, chrome vanadium steel, lacquered silver.'

L b RCode size mm mm g S €'

70020002 125 125 15 96 10 7.8570020003 150 150 18 172 10 9.5570020004 175 175 21 269 10 12.4070020005 200 200 24 379 5 14.301

70020007 250 250 25 479 5 19.3070020008 300 300 26 591 5 24.00'

Cross-cut chisels103DIN 6451, flat, chrome vanadium steel, lacquered silver.'

L b RCode size mm mm g S €'

70040003 150 150 16 147 10 9.8570040004 175 175 17 239 10 12.4070040005 200 200 18 340 5 15.50'

Grooving chisel110flat, chrome vanadium steel,lacquered silver.

'

L b RCode mm mm g S €'

70080001 240 26 292 5 13.90'

Grooving chisel112as No 110,but with finger protector.

'

L b RCode mm mm g S €'

70080002 240 26 411 5 16.90'

Finger protector112/1for Cold Chisels No 102 and Cross-cut Chisels No 103 from 200 mmonward, for Grooving chisel No 110, shaft section 23 x 13 mm.

'

RCode g S €'

79160001 101 5 4.60'

8

244

Drift pins104DIN 6458, octagonal,chrome vanadium, lacquered silver.

'

x w L RCode size mm mm mm g S €'

70060007 120 x 2 2 10 120 60 10 5.4570060010 120 x 3 3 10 120 60 10 5.4570060002 120 x 4 4 10 120 62 10 5.4570060008 120 x 5 5 10 120 64 10 5.701

70060003 120 x 6 6 10 120 66 10 5.7070060009 120 x 8 8 12 120 68 10 5.70'

Centre punches105DIN 7250, octagonal,chrome vanadium, lacquered silver.

'

w L RCode size mm mm g S €'

70050001 100 x 10 10 100 52 10 4.5570050005 120 x 10 10 120 63 10 5.2570050002 120 x 12 12 120 90 10 5.50'

Parallel pin punches108DIN 6450, octagonal,chrome vanadium, lacquered silver.

'

x w L RCode size mm mm mm g S €'

70071152 115 x 2 2 8 115 30 10 6.4070070013 125 x 3 3 8 125 35 10 5.4570070001 150 x 2.5 2.5 10 150 65 10 5.3570070002 150 x 3 3 10 150 62 10 5.301

70070003 150 x 4 4 10 150 64 10 5.2570070004 150 x 5 5 10 150 67 10 5.3070070005 150 x 6 6 10 150 72 10 5.6070070006 150 x 8 8 10 150 81 10 5.601

70070009 175 x 3 1) 3 10 175 57 10 5.9570070010 175 x 4 2) 4 10 175 64 10 5.9570070012 175 x 6 3) 6 10 175 69 10 9.7570070008 200 x 8 8 12 200 141 10 7.151

70070011 200 x 10 10 12 200 159 10 7.15'

1) for use on OPEL Kadett C2) for use on Mercedes-Benz3) with guide bush for use on retaining pins of disc brake pads, all brake calipers on OPEL Ascona B, C, Manta B, Kadett D, Astrax diameter of tipw size of handle, octagon'

Pin punches109with guide bush.

'

v x L RCode size mm mm mm g S €'

70090001 1 0.9 5 80 7 10 8.6070090002 2 1.4 5.5 82 12 10 8.5070090003 3 1.8 6 86 12 10 8.1070090004 4 2.4 7 95 18 10 8.101

70090005 5 2.8 7 97 19 10 8.1070090006 6 3.4 8 100 25 10 8.1070090007 7 3.9 9 100 27 10 8.1070090008 8 * 5.9 10 103 47 10 6.25'

v diameter of tipx diameter of handle* without guide bush'

ES 102/108/109/4

175 x 350 x 30 mm, 4 pieces'

RCode g €'

96838123 555 43.70'

No 102 175 mm'

No 108 150 x 6; 175 x 6 mm'

No 109 size 6; 100 x 3.4 mm'

83812027 Empty tray 115 7.85'

ES 102/105/108/8

175 x 350 x 33 mm, 8 pieces'

RCode g €'

96838124 900 58.15'

No 102 175 mm'

No 105 120 x 12 mm'

No 108 150 x 2.5; 150 x 3; 150 x 4; 150 x 5;150 x 6; 150 x 8 mm

'

83812036 Empty tray 114 7.85'

Sets: Chisels, pins, punches102-5/66 piecesContent: 1 each

No 106/125 mmNo 106/150 mmNo 107/125 mmNo 104/120 x 2; 120 x 4 mmNo 105/120 x 10 mm

D = in plastic standPc = in plastic wallet

'

RCode No g S €'

98812201 102-5/6 D 445 1 32.8098812202 102-5/6 Pc 426 5 32.80'

Set: Drift pins, centre punches104-5/6D6 piecesContent: 1 each

No 104/120 x 2; 120 x 3; 120 x 4; 120 x 5;120 x 6 mm

No 105/120 x 10 mmin plastic stand

'

RCode g S €'

96700601 417 1 33.25'

8

245

Pin punch-/centre punch set105-8/6K6 pieces in transparent plasticcontainer stand.Content: 1 each

No 108/150 x 2.5; 150 x 3; 150 x 4; 150 x 5;150 x 6 mm;

DIN 6450/ Form C No 105/120 x 10 mm; DIN 7250

'

RCode g S €'

96700711 483 1 32.05'

Sets: Parallel pin punches108/66 piecesContent: 1 each

No 108/150 x 2.5; 150 x 3;150 x 4; 150 x 5; 150 x 6;150 x 8 mm

D = in plastic standPc = in plastic wallet

'

RCode No g S €'

96700701 108/6 D 450 1 32.4096700702 108/6 Pc 424 5 32.40'

TCS 102–109/10956/10960/6

xö175 x 350 x 40 mm, 6 pieces'

RCode g €'

96838181 1500 91.15'

No 10956 O 35 mm'

No 10960 500 g'

No 102 175 mm'

No 108 150 x 6; 175 x 6 mm'

No 109 size 6; 100 x 3.4 mm'

TCS 102-108/11

xö175 x 350 x 33 mm, 11 pieces'

RCode g €'

96838754 1665 104.20'

No 102 150; 200; 250 mm'

No 105 120 x 10; 120 x 12 mm'

No 108 150 x 2.5; 150 x 3; 150 x 4; 150 x 5;150 x 6; 150 x 8 mm

'

TCS 102–108/10957/10960 MF

xö

530 x 350 x 40 mm, 12 pieces'

RCode g €'

96830355 3343 207.95'

No 102 200 mm'

No 103 150 mm'

No 105 120 x 10 mm'

No 108 150 x 3; 150 x 4; 150 x 5; 150 x 6;150 x 8 mm

'

No 10957 O 40 mm'

No 10960 500; 800 g'

No 12718'

TCS 102–108/10957/12718/13

xö

530 x 350 x 40 mm, 13 pieces'

RCode g €'

96830226 3730 213.80'

No 102 200 mm'

No 103 150 mm'

No 105 120 x 10 mm'

No 108 150 x 3; 150 x 4; 150 x 5; 150 x 6;150 x 8; 200 x 8 mm

'

No 10957 O 40 mm'

No 10960 500; 800 g'

No 12718'

TCS 102–108/10960/10

xö175 x 350 x 40 mm, 10 pieces'

RCode g €'

96830361 1569 98.65'

No 102 200 mm'

No 105 120 x 12 mm'

No 108 115 x 2; 150 x 3; 150 x 4; 150 x 5;150 x 6; 175 x 4; 200 x 8 mm

'

No 10960 500 g'

8

246

TCS 102–108/10957/10960/13

xö

530 x 350 x 60 mm, 13 pieces'

RCode g €'

96830177 5540 239.65'

No 102 200; 300 mm'

No 103 175 mm'

No 105 120 x 12 mm'

No 108 150 x 3; 150 x 4; 150 x 5; 150 x 6;150 x 8 mm

'

No 10957 O 50 mm'

No 10960 500; 800; 1000 g'

TCS 102–108/10957/10960/16

xö

530 x 350 x 45 mm, 16 pieces'

RCode g €'

96830609 3715 255.10'

No 102 200 mm'

No 103 150 mm'

No 105 120 x 10 mm'

No 108 150 x 3; 150 x 4; 150 x 5; 150 x 6;150 x 8 mm

'

No 10957 O 40 mm'

No 10960 500 g'

No 12373'

No 12600 500 g'

No 12718'

No 12931 3 m'

No 65 64 2 250'

No 39 cars 400 mm'

TCS 102–108/10956/10960/18

xö

530 x 350 x 55 mm, 18 pieces'

RCode g €'

96830620 3653 240.30'

No 102 150 mm'

No 103 150 mm'

No 105 120 x 10 mm'

No 108 150 x 2.5; 150 x 3; 150 x 4; 150 x 5;150 x 6; 150 x 8 mm

'

No 10956 O 50 mm'

No 10960 300; 500 g'

No 10356'

No 10670 285 mm'

No 10672 20 x 315 mm'

No 12374'

No 12900N'

No 12965'

Three square engineers scrapers10670special steel.

'

L RCode mm g S €'

72060101 215 106 5 9.2572060103 265 124 5 9.7572060104 285 140 5 10.7072060105 310 152 5 11.50'

Flat engineers scrapers10672special steel.

'

RCode mm g S €'

72050104 20 x 315 227 5 11.8072050105 25 x 365 367 5 14.20'

Three square engineers bearingscraper

10676

special steel.

'

RCode mm g S €'

72080103 85 x 12 x 315 160 5 11.40'

8

247

Engineers file, round12025

'

L RCode mm g S €'

72120100 210 118 5 12.20'

Engineers file, half round12030

'

L RCode mm g S €'

72130100 260 317 5 22.40'

Engineers file, three-square12035

'

L RCode mm g S €'

72140100 210 201 5 16.10'

Engineers file, hand12036

'

L RCode mm g S €'

72170102 260 339 5 16.40'

Hand vice12200forged C 35,width of jaws 48 mm.

'

L RCode mm g S €'

71200000 145 673 1 34.10'

Tubular hacksaw12050adjustable,with blade size 300 mm/12".

'

L RCode mm g S €'

72210000 465 490 1 19.60'

Spare hacksaw blades for No 1205010 pieces, H.S. Steel, 24 teeth per inch.

'

L RCode mm g S €'

79180001 300 174 1 26.70'

Hacksaw frame12053

'

L RCode mm g S €'

72210002 252 159 1 10.90'

Spare hacksaw blades for No 120536 pieces, Chrome Alloy Tool Steel, 32 teeth per inch.

'

L RCode mm g S €'

79180002 158 23 1 3.00'

ES 10670–13110/11

530 x 350 x 35 mm, 11 pieces'

RCode g €'

96838173 2120 153.85'

No 10670 265 mm'

No 12025 210 mm'

No 12030 260 mm'

No 12035 210 mm'

No 12036 260 mm'

No 12050 465 mm'

No 12320'

No 12321'

No 12377'

No 12931 3 m'

No 13110 300 mm'

83812088 Empty tray 301 21.50'

8

248

TCS 12025–13110/11

xö

530 x 350 x 35 mm, 11 pieces'

RCode g €'

96838759 2070 178.50'

No 12025 210 mm'

No 12030 260 mm'

No 12035 210 mm'

No 12036 260 mm'

No 12050 300 mm'

No 12320'

No 12321'

No 12718'

No 12931 3 m'

No 12965'

No 13110 300 mm'

Stud remover set905/25M 5–M 16, 3/16"–5/8", 25 pieces,in green plastic box.Content:5 HSS twist drills sizes

(3.2; 4.8; 6.4; 8; 8.7 mm)5 Fluted Removal Pins sizes 1–5

for threads M 5–M 165 Splined Nuts, sizes 1–5

10 Drill Guides, sizes 1–10

'

RCode g S €'

96713025 555 1 113.00'

Spare parts906Removal pins and splined nuts, in pairs in plastic bags.

'

for RCode size threads g S €'

71310001 1 M5–M6 3/16–1/4" 14 1 6.5571310002 2 M7–M8 1/4–5/16" 20 1 7.5071310003 3 M10 3/8" 33 1 8.9571310004 4 M12 7/16" 46 1 10.601

71310005 5 M14–M16 1/2–9/16" 65 1 12.20'

Universal thread restorers12000suitable for inside andoutside threads.

'

L RCode size mm g S €'

72100004 ISO 230 119 10 44.1072100003 SAE 230 118 10 45.2072100002 WW 230 122 10 44.10'

|–––– ISO ––––| |–––– Ww ––––| SAE/USSPitch metr. threads Whitworth threadsmm thread per inch thread per inch'

'

0.80 5 24 3/16 + 7/32 241.00 6 + 7 20 1/4 201.25 8 + 9 18 5/16 181.50 10 + 11 16 3/8 161.75 12 14 7/16 142.00 14 + 16 12 1/2 + 9/16 132.50 18, 20, 22 11 5/8 + 11/16 123.00 24 + 27 10 3/4 + 13/16 11'

Screw pitch gauge126650.25 to 6 mm and 4 to 62 t.p.i.(metric/Whitworth threads).

'

RCode size g S €'

77270003 52 79 10 6.55'

Screw EXTRACTOR set900/6Pcin green plastic bag.

'

RCode Content g S €'

96710101 1 each No 900 size 1–6 220 5 48.95'

Screw EXTRACTOR900

'

for D D L recommend. RCode size bolts mm " mm Drill g S €'

71010001 1 M3–M4 1/8–5/32" 3 1/8 51 2 mm 5/64" 3 10 5.9571010002 2 M5–M7 3/16–1/4" 3.4 9/64 62 3 mm 7/64" 6 10 7.3571010003 3 M8 5/16" 4.9 3/16 70 5 mm 3/16" 10 10 7.3571010004 4 M10–M12 3/8–7/16" 7 9/32 77 6.4 mm 1/4" 20 5 8.801

71010005 5 M14–M16 1/2–9/16" 9 23/64 88 8 mm 5/16" 48 5 9.2071010006 6 M18–M22 5/8–3/4'' 12 31/64 98 12 mm 15/32" 92 5 10.90'

8

249

Stud remover904• Suitable for all sizes of studs from 6–12 mm. • Also suitable for percussion screwdriver use.• Will cope with rusted or scale-coated screwswith a minimum of 3 mm protruding.

Chuck: size 36 mmClamping screw: size 24 mm

'

a RCode " g S €'

71340000 3/8 420 1 147.00'

Nut splitters12615galvanised, for splitting Nuts ofquality range up to 8.8 (55 tpsi).

'

for nuts RCode size mm g S €'

71250011 1 10–18 193 1 64.0071250012 2 19–27 386 1 66.00'

Vernier calliper12900Nas per DIN 862,vernier readings 1/20 mm and1/128", stainless steel,c/w plastic pouch.

'

measuring range RCode mm/" g S €'

77371001 150/6 185 1 36.20'

Vernier calliper12900/1Nwith a large digital display, automatic shut-off, switch for mm/inches, depth gauge,RS232C interface, spare battery,differential measurements by means of 0 reset function, display accuracy0.01 mm / 0.0005", in plastic case.

'

measuring range RCode mm/" g S €'

77371002 150/6 312 1 92.50'

Brake disc gauge12900/2NDIN 862, for measuring thethickness of car and motorcyclebrake discs in situ, stainless steel,with locking screw and trailingvernier scale (1/10 mm), in woodenstorage box.

'

measuring range throat depth RCode mm mm g S €'

77371003 60 55 233 1 105.00'

Tape measure12931with tape lock. Metric-Inch scales.

'

L RCode m g S €'

77040004 3 104 10 12.30'

Workshop micrometers12935NDIN 863, chrome plated.• With clamping ring and precisionratchet knob

• With insulating plates• Tungsten carbide anvil• Readings 0.01 mm

'

measuring range Pitch RCode size mm mm g S €'

77411001 1 0–25 0.5 297 1 40.9077411002 2 25–50 0.5 461 1 50.5077411003 3 50–75 0.5 601 1 62.5077411004 4 75–100 0.5 809 1 78.50'

Steel rule13110Metric-Inch scales, length 300 mm.

'

Divisions Divisions RCode Top Edge " Lower Edge mm g S €'

77460001 1/16, 1/32, 1/64 0.5; 1 26 5 4.80'

Ratchet tap holders12915steel, chrome plated.

'

Capacity L RCode size mm DIN 1) ISO 2) mm g S €'

77390001 1 2.0–5.0 M3–8 M1–6 85 180 1 17.2077390002 2 4.6–8 M5–12 M6–12 110 305 1 22.30'

1) for taps DIN2) for taps ISO'

Set warding files128006 pieces, in Pc-wallet, DIN 7283,Content: 1 file each, hand,flat, half round, three square, square, round

'

L RCode mm g S €'

72230001 100 111 5 17.70'

Set of needle files131006 pieces, in plastic wallet,Content: 1 file each,round, half round,three square, square,hand, flat

'

L RCode mm g S €'

96722801 140 46 1 54.50'

8

250

Padlock12932

'

RCode g S €'

77210002 85 1 12.70'

Force feed oil can12250metal container, brass pump.Content: 500 ccm

'

RCode g S €'

77010001 270 1 22.60'

Plastic oil can12251Content: 250 ccm

'

RCode g S €'

77110002 80 5 9.55'

Electricians cable knife12320with stainless blade.

'

Blade RCode mm g S €'

77020000 90 81 10 12.30'

Engineers scriber12321

'

L RCode mm g S €'

77100000 250 31 10 3.70'

Wire brush12374wood, steel wire dia. 0.35 mm.

'

L RCode mm Rows g S €'

77090000 290 4 129 10 2.60'

Wire brush12377with brass coated steel bristles.

'

L RCode mm g S €'

77090010 270 140 24 2.80'

File brush12378

'

L RCode mm g S €'

77250000 260 74 5 4.20'

Brass wire brush13115for use on light alloys.

'

L RCode mm Rows g S €'

77470001 280 4 134 1 6.55'

Scraper12481

'

L b RCode mm mm g S €'

77070000 212 60 65 10 3.85'

Magnetic lifters12600Loss of adhesion above 80°C.

'

lifting power O L RCode g mm mm g S €'

77260027 270 1) 5 500 25 1 7.5577260025 500 8 460 70 1 18.5077260060 1800 15 520 230 1 27.9077260200 3000 19 535 297 1 48.00'

1) Miniature magnetic lifter with tiny head, very powerful'

500-3000

270

Adjustable hook spanners12910for slotted nuts as per DIN 1810,adjustable.

'

A RCode size mm g S €'

44010001 1 20–42 90 5 26.3044010002 2 45–90 245 5 28.4044010003 3 95–165 686 5 50.50'