+ All Categories
Home > Documents > SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the...

SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the...

Date post: 25-Sep-2020
Category:
Upload: others
View: 0 times
Download: 0 times
Share this document with a friend
13
Aeroprakt Ltd Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31 AEROPRAKT SERVICE BULLETIN No. SB A32-05 REINFORCEMENT OF THE FRAME No.10 OF A32 AND A32L AIRCRAFT Repeating symbols: Please, pay attention to the following symbols throughout this document marking important information. p WARNING: Identifies an instruction, which if not followed may cause serious injury or even death. n CAUTION: Denotes an instruction, which if not followed, may cause severe damage. u NOTE: Information useful for better handling. Release date: 19.07.2018 Effective date: 19.07.2018 Completion date: Superseded notice: Model: A32, A32L Serial number(s) affected: All A32 aircraft to and including s/n 053 and all A32L aircraft to and including s/n 017 Page 1 of 13
Transcript
Page 1: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

Aeroprakt Ltd Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

AEROPRAKT

SERVICE BULLETIN No. SB A32-05

REINFORCEMENT OF THE FRAME No.10 OF A32 AND A32L AIRCRAFT

Repeating symbols:

Please, pay attention to the following symbols throughout this document marking important information.

p WARNING: Identifies an instruction, which if not followed may cause serious injury or even death.

n CAUTION: Denotes an instruction, which if not followed, may cause severe damage.

u NOTE: Information useful for better handling.

Release date: 19.07.2018

Effective date: 19.07.2018

Completion date:

Superseded notice:

Model: A32, A32L

Serial number(s) affected: All A32 aircraft to and including s/n 053 and

all A32L aircraft to and including s/n 017

Page 1 of 13

Page 2: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 2 of 13

1) Planning information

1.1) Aircraft affected

All A32 airplanes, S/N to and including 053 and all A32L airplanes, S/N to and including 017.

1.2) Reason

In case if excessive impact of the tail skid against the ground during take-off or landing the frame No. 10 may be damaged.

1.3) Subject

Frame No.10 of the fuselage tail boom.

1.4) Compliance

Compliance with this Service Bulletin is mandatory for all affected aircraft for flight safety reasons!

1.5) Approval

The technical content of this Service Bulletin has been approved by Aeroprakt.

1.6) Manpower

Estimated work: 16 man-hours.

1.7) Mass data

Mass change – insignificant.

1.8) Revision of other documents

None.

1.9) Spare parts

Reinforcing doubler and set of rivets.

2) Spare parts information Price of the mod kit: consult your local dealer. NB > Please see pages 11-14 inclusive for special time saving instructions which are factory-approved for Australian registrered A32 Vixxen aircraft

Page 3: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 3 of 13

3) Accomplishment / Instructions

p WARNING: Non-accomplishing this work may result in failure of the frame No.10.

3.1) Remove the tail fairing of fuselage by undoing 14 screws (Fig.1).

Fig. 1.

3.2) Disconnect the AMHT (all-moving horizontal tail) antiservo/trim tab control cable (Fig.2).

Fig. 2.

Page 4: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 4 of 13

3.3) Disconnect the AMHT control pushrod (Fig.3).

Fig. 3.

3.4) Remove the AMHT by undoing its two attachment bolts (Fig. 4).

Fig. 4.

Page 5: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 5 of 13

3.5) Remove the tail skid from the frame No. 10 (Fig. 5).

Fig. 5.

3.6) Undrill two flush head rivets marked with arrows in Fig. 6.

Fig. 6.

Page 6: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 6 of 13

3.7) Undril 5 rivets on the bottom side of the tail boom at the frame No. 10 (Fig 7).

Fig. 7.

Page 7: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 7 of 13

3.8) Install the reinforcing doubler with bolts as shown below, use a 90° drill to mark position of holes in the flanges of the reinforcing doubler through the holes in the frame No. 10 (Fig. 8).

Fig. 8.

Page 8: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 8 of 13

3.9) Mark with a marker the holes in the doubler through the holes in the fin spar (Fig. 9).

Fig. 9.

Page 9: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 9 of 13

3.10) Round the sharp edge of the fin spar flange to ensure a better fit of the doubler (Fig. 10).

Fig. 10.

3.11) Attach the doubler with temporary bolts, install two rivets with flush heads and two rivets with normal heads on the fin spar (Fig. 11).

Fig. 11.

Page 10: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 10 of 13

3.12) Install the rivets on the flanges of the doubler (Fig. 12).

Fig. 12

3.13) Install back the AMHT in reversed order.

Page 11: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 11 of 13

Alternative installation method – as approved by Aeroprakt for Australian registerd aircraft

1) Instead of solid rivets use Cherry Max rivets P/N CR3213-4-3 at the location shown in the picture below.

Cherry Max rivets P/N CR3213-4-3

Page 12: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 12 of 13

2) Replace the solid rivets with screws and nuts at the location shown in the picture below:

1) MS 27039-0809 screws 2) MS 27039-808 screw

Page 13: SB A32-05 revise2) Replace the solid rivets with screws and nuts at the location shown in the picture below: 1) MS 27039-0809 screws 2) MS 27039-808 screw AEROPRAKT SERVICE BULLETIN

AEROPRAKT SERVICE BULLETIN No. SB A32-05

Address: 24, Polyova str., 03056 Kyiv, Ukraine E-mail: [email protected], [email protected] phone: +38 044 496 77 21, fax: +38 044 496 77 31

Page 13 of 13

3) Instead of solid rivets use Cherry Max rivets P/N CR3213-4-3 at the location shown in the picture above.

CR3242-4-3 C/S cherry Rivets. CR3213-4-3 Cherry Rivets


Recommended