Package Content:SCOPIA XT1000 Codec Unit•
SCOPIA XT1000 Standard Camera•
SCOPIA XT1000 Digital Microphone Array Pod•
SCOPIA XT1000 Remote Control Unit•
Codec Unit Camera Cable•
HDMI Cable•
Digital Microphone Array Pod Cable•
Ethernet Cable for LAN•
Power Supply and Power Cable•
VGA to DVI Adapter and DVI to DVI Cable•
Coaxial Digital Audio Cable•
Diagnostic Cable Adapter•
Base for SCOPIA XT1000 Codec Unit•
Remote Control Batteries•
SCOPIA XT1000 Quick Setup Guide
© 2010 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION Ltd. retains all rights not expressly granted.This publication is RADVISION confidential. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by RADVISION Ltd. No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by RADVISION Ltd. or its agents. RADVISION Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. RADVISION Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact RADVISION Ltd. and a copy will be provided to you. Unless otherwise indicated, RADVISION registered trademarks are registered in the United States and other territories. All registered trademarks recognized. All right reserved.For further information contact RADVISION or your local distributor or reseller. http://www.radvision.com
Date and Time SetupUse the up and down arrow keys 1. to navigate to the Day field. Press the 2. button on the remote control to delete the date.Enter today’s date. 3. Use the up and down arrow keys 4. to move to the next field.Repeat the procedure for the 5. Month, Year, Hour, and Minutes. Then select Next.
Network Settings Enter your network settings. For questions about this information, consult your system administrator. Then select Finish.
System Installation and ActivationConnect all cables to the SCOPIA XT1000 Codec Unit (see overleaf).1. Turn on the TV monitors. 2. Make sure the remote control has batteries installed.3. Verify that the LED on the front panel of the Codec Unit is blinking.4. Turn on the Codec Unit by pressing the 5. button on the remote control or the Power button on the back of the Codec Unit. The RADVISION welcome screen appears on the monitors.6.
A
Country and Language of InterfaceSelect the Country and preferred Language. Then select Next.
C
Codec Unit Display Name The 1. System Name field displays the name of this Codec Unit as displayed in a video conference, for example:
Hong Kong,• or 9th Floor Conf Rm• , orNY Office•
Use the remote control keypad to 2. type the name. Then select Next.
Moving the Camera On the general screen, navigate 1. to Cameras using the arrow keys.Select 2. Move camera.Use the arrow keys to move the 3. camera to the preferred position. Select 4. Stop moving camera.Repeat the procedure if you have 5. a second camera installed.
Graphics and Image Setup If all the sides of the orange frame are visible on your monitor, select Yes, otherwise select No.
Select 1. OK. The first slider is highlighted in orange. Use the right and left arrow keys 2. to move the slider until the Top orange frame is fully visible on your monitor. Move to a different slider with 3. the up and down arrow keys.Repeat the procedure for the 4. Left, Bottom, and Right side. Select5. Next.
D
E
G H
F
Product RegistrationOpen the envelope that came with the XT1000.1. Locate the serial number and product key.2. On a computer, open a browser and navigate to 3. http://www.radvision.com/XT1000.Complete the online registration form and enter the serial number and product 4. key. The web registration form returns a license key.Write down the license key and keep it in a safe place for future use.5.
B
CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.
P/N 62111-00001-A01
MK
T-D
I-21
0610
-01
SCOPIA XT1000 Quick Hardware Setup
CAUTION: Make sure all units are switched off whenever connecting or disconnecting devices.
To set up the codec vertically on its base, remove the cover on the left side of the Codec Unit and insert it into its base. Fully turn the connecting screw on the base, and make sure it is completely secured.
10/100/1000
XNET
DIAG
HD CAM
2
HD CAM
HD
CTRLDVI-I IN
S/PDIF
10/100
1
CAMOUTPUT12V 2.2A
24V 3.75A
1 HD 2
CAUTION: the mains cable is used as a disconnecting device, use therefore an easily accessible outlet located near the device for the power supply connection. Never remove the mains plug while the device is connected.
Optional
SCOPIA XT1000 Codec Unit
Camera
Digital Media DeviceFor more information on installing the optional camera, see the SCOPIA XT1000 User Guide.
Remote Control Batteries
LITHIUM BATTERY 3V
LITHIUM BATTERY 3V
4
10
18
1116 15
12
17
78
5 9
6
3
2
1
DC IN 12V OUT RS-232C IN DVI
Optional Camera
13
14
DC IN 12V OUT RS-232C IN DVI
INOUT
Layouts PiP Inputs Help
SelectMemo
Far Near Presets
Package Content:
Codec Unit
Standard Camera
Digital Microphone Array Pod
Remote Control Unit and Batteries
Codec Unit Camera Cable
HDMI Cable
Digital Microphone Array Pod Cable
Ethernet Cable for LAN
Power Supply and Power Cable
VGA to DVI Adapter
DVI to DVI Cable
Coaxial Digital Audio Cable
RADVISION Optional – Not Included Accessories
Standard Camera
Digital Microphone Array Pod
Non-RADVISION
HDMI Cable for HD2
LAN Cable
Coaxial Digital Audio Cable
VGA to DVI Cable