PRi
PLUGS AND RECEPTACLES INDEX
PR
Section PR
Introduction/Features
Applications.........................................2 - 5
VP/VR/VPR Series
30 amp including new “AT” models .............6
VP/VR/VPR Series
60 amp including new “AT” models .............7
VP/VR/VPR Series
100 amp including new “AT” models ...........8
VP/VR/VPR Series
200 amp ...................................................9
VSQ (VWSQ Series NEMA 4)
Interlocked Switched Receptacles ..........10
VSQ-FS Series
Factory Sealed Receptacles ...................11
VBQ Series
Interlocked Breaker Protected
Receptacles.....................................12 - 13
VSI Series
Plugs and Switched Receptacles.....14 - 16
VCR Series
Clean Room Receptacles........................17
KR Series
Introduction.............................................18
KR Series
20, 30 and 60 amp ..........................19 - 21
UGP/UGR Series
Plugs and Receptacles ....................22 - 23
Adapter, Grips and Handlamps...............26
UGRC Series
Connector ...............................................24
UGRP Series
Panel Mount Receptacle .........................25
UGRGF Series
GFI Protector Receptacle........................26
UGFI Series
Ground Fault Protector ............................27
HAZARDOUS LOCATIONS –BLADE STYLE
NEMA 4X
HAZARDOUS LOCATIONS –INTERLOCKED
HAZARDOUS LOCATIONS –DELAYED ACTION
HAZARDOUS LOCATIONS –INTERLOCKEDI.E.C. CONFIGURED
PRi PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRR
VERSAMATE® SERIES • PLUGS AND RECEPTACLESNEMA 4X METALLIC
PR2
FEATURES-SPECIFICATIONS
THE FIRST NEMA 4X RATED LINE OFMETALLIC PLUGS & RECEPTACLES.
VersaMate® metallic pin & sleeve plugs & receptacles aredesigned for heavy duty industrial use. These devices sup-ply power to both fixed and portable electrical equipmentincluding pumps, generators, welders, vacuums, blowersand similar apparatus.
Suitable for indoor or outdoor use. Applications include thewet, cold, hosedown, hazardous or corrosive areas in suchindustrial applications as:
• Pulp & Paper Mills • Breweries• Electrical Power Plants • Refineries• Petrochemical Plants • Chemical Plants• Wastewater Treatment • Grain Facilities • Marine, Docks, Ports • Textile Manufacturing• Construction Sites • Food Processing Facilities
Standard Materials:Copper-free aluminum construction with electrostaticallyapplied epoxy/polyester finish. Contacts are brass with apatented beryllium copper spring tensioner. External screwsare 316 stainless steel.
Features:The VersaMate product line includes 30, 60, 100 and 200Amp plugs, receptacles and connectors with a full range ofback boxes. Popular options include reverse service andpolarization. The VersaMate line is FULLYINTERCHANGEABLE1 with UL1686 configured and listeddevices such as Crouse-Hinds® Arktite® or Appleton®
Powertite®. Standard location receptacle bolt hole patternsmatch competitive back boxes so users can upgrade toVersaMate without changing back boxes in instances wherechanging the conduit system is difficult.
600 VAC/250VDC; 50-400 HertzNEMA 3, 4, 4XClass I, Div. 1 & 2, Groups B,C,D; NEMA 7 B,C,D2Class l, Zones 1 & 2, llB+H2, llA2Class ll, Div. 1 & 2, Groups F & G;NEMA 9 F,G2Class lll2
1VersaMate® components are UL classified and intermateable with other UL
1686-C1 configured devices (when installed in accordance with instructions
furnished with device). Assemblies containing components from other manu-
facturers would have the NEMA type rating of the lowest rated device.
2See product pages for specific ratings.
Arktite® is a registered trademark of Crouse-Hinds®.
Powertite® is a registered trademark of Appleton®.
Plugs:Octagonal style (Patented) for a firm and sure
grip when connecting or disconnecting is fea-
tured on both plug and cable connector
bodies. Insulators have high mechanical and
dielectric strength and “Low Arc Tracking.”
“Increased Safety” type box terminals with
gripper ribs securely clamp around conductors.
Funneled conductor entry chambers lead all properly stripped
conductors into terminals simultaneously. NEMA 4X rating
when inserted into VersaMate receptacle and locking ring is
tightened.
Receptacles:Exclusive Patented “Breech-Lock” cap
serves as either flip lid or screw cover.
Receptacle is NEMA 3R with lid snapped
shut or NEMA 4X with lid turned shut or
when VersaMate plug is inserted and locking
ring tightened. Patented notch in cap arm
holds cap open for easy plug insertion or
maintenance. Patented pin design uses slotted spring clip which
avoids excessive wear while providing continuous electrical pin
to sleeve contact. VersaMate® receptacles use the same
“Increased Safety” terminals and funnel design as
VersaMate® plugs.
Cable Clamping Assembly:Plugs and cable connectors are
supplied with an exclusive neoprene
“Onion Skin” peel-away type grom-
met. The VersaRange® cable clamp
system captures cable with four
grip points using only two tighten-
ing screws. Clamp guide assembly provides a firm fit over a
wide range of cable diameters. Non-removable set screws pre-
vent clamp guide assembly from backing out. Clamps have
smooth contoured shoulder design to prevent snags or damage
when moving equipment.
Back Boxes:VersaMate back boxes come in a variety of
mounting styles. Exclusive “blind” recepta-
cle mounting holes prevent moisture from
entering box via thread cavities. Boxes
come with a green grounding screw.
VSQ VBQVR/VP
NEW
ALLEN/SLOTTERMINALS
PR2PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222
VERSAMATE® SERIES • PLUGS AND RECEPTACLESFEATURES AND COMPARISONS
PR3
KILLARK BRAND
PR
New Allen/slot terminal screws donot contact or machine conductor.Allows higher torque values typicalin the oil industry.
VersaMate original Phillips/slot“Increased Safety” type terminalsreduce connection fatigue.Screws do not contact or machineconductor and are under springtension to reduce loosening andpullout due to vibration.
Conventional screw type terminals. Screws “machine”(grind or fray) conductor.Screws are not under tensionand more easily loosen fromheating and cooling cyclesor from vibration. Screws canfall out (and be lost) duringinitial shipment-requiresreassembly.
“Breech-Lock” design serves as both flip lid or screw coverstyle. Special notch in lid armholds cover open to ease pluginsertion or maintenance.
Conventional caps: usermust choose between fliplid's convenience or screwcover's better sealing capa-bilities. Broken chains canmean lost covers.
Exclusive "Onion Skin" style gas-ket assures a tight seal aroundcable. Skin layers are removedfrom a single gasket to adjust forvarious cable diameters.
Multiple gaskets requiretrial & error sizing to be sure of best fit andseal.
Versatile range Cable Clamp system captures cable at fourgrip points using only twoscrews. Smooth contoureddesign avoids snags when moving equipment.
Standard clamps squeezeand pinch cable. Protrudingscrews snag or scratchwhen moving equipment.Other clamp systems withmultiple screws are difficultto tighten evenly.
*
*Slip pencil or screwdriver into notch.
TERMINALS
CAP
GASKET
CABLE CLAMP
OTHER BRANDS
ALLEN/SLOTTERMINALS
• First NEMA 4X - Still the BEST!
• Exclusive interior gasketing
• Exclusive Terminal Designs
• No conductor machining
• Allen or Phillips types
• Exclusive Onion-Skin Gasket
• Perfect Cable Fit
• Exclusive 4-Point Cable Grip
• Uses only 2 Recessed Screws
• Exclusive Breech-Lock Cap
• Flip or Screw-On
• Notch to hold openNEW!
PR3 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR3
VERSAMATE® SERIES • PLUGS AND RECEPTACLESFEATURES
PR4
EXCLUSIVE FEATURES:
Patented Exclusive “Breech-Lock” capserves as either flip lid or screw cover
• NEMA 3R Rating:When receptacle capis snapped shut
• NEMA 4X Rating:When receptacle cap isturned shut or withVersaMate
®
plug insertedand ring tightened
PatentedSpecial notch is designed to hold cap open for easy fieldservice or plug insertion withtwo free hands
Key user needs were identified from “Focus Groups” comprised of Design Engineers, Contractors,and Maintenance Personnel. Input from these forums resulted in VersaMate’s unique features.
Keyway prevents incorrect plug insertion
O-ring seals
Custom pin designusing slotted springclip to provide superior contact and reliability
Sleeveincorporates contaminaterelief port
Exclusive neoprene “Onion Skin” peel-away type gasket for the ultimate in sealing a variety of cable sizes
VersaRange®
Cable clamp systemcaptures cable with four grip pointsusing only two tightening screws.Provides secure grip without damaging the cable insulation
•
•
••
•
•
• Smooth shoulder contour prevents snags & hang ups
NEW 30,60,100A “AT” Allen/Slotor “Increased safety” Phillips/Slotterminals provide secure clamp-ing of conductors
Funneled wiring chamber design for fast and accurate conductor insertion to speed assembly. All wires can be inserted at one time
PatentedBody style with octagonalshape for easy grip
P
•
•P•P
Unique VersaMate® FeatureThe VersaMate® Line is designedfor the industrial customer basedon engineering and user surveys
O-ring seals
• Funneled wiring chamberdesign for fast and accurate conductor insertion to speed assembly. All wires can be inserted simultaneously
Denotes Patented Feature•P
PR4PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR444444444444444444444
VERSAMATE® SERIES • PLUGS AND RECEPTACLESNEMA 4X METALLIC
PR5
PR
REVERSE SERVICE: S39Add suffix S39 for factory Reverse Serviceof receptacles, plugs or connectors.Receptacles or connec-tors are assembled withplug interiors whileplugs are assembledwith receptacle interiors.For applications wherethe plug is energized(i.e. from a generator) tofeed a non-energizedreceptacle. Preventseasy contact with energized exposed pins. This conversioncan be performed in the field with a complementary plug &receptacle (30A to 100A devices shown on pages PR6-8).200A Amp devices shown on page PR9 are a factory-onlyoption. Reverse Service is not for hazardous locations.
Style I
In a Style I plug, the cable’s ground conductor is bonded to the plug housing by means of solderless connector. Thereceptacle is grounded by being part of a grounded conduitsystem. Upon insertion, detent springs in the receptaclehousing contact and ground the plug housing before currentcarrying poles. All poles are current carrying.
GROUNDING: To minimize the danger of electrical shock when utilizingportable equipment, the National Electrical Code requiresexposed metal parts be grounded if operated at more than150 volts to ground. The VersaMate® plug & receptacle sys-tem is available in two grounding styles. Please note Style Iand II devices cannot be intermated.
POLARIZED OPTION: S37Add suffix S37 for special polarity.
Can prevent connection between mismatched voltages or frequencies in areas where devices of the same amperage,poles and grounding style are used. Receptacle or connectorinteriors are rotated 22-1/2° to the right; plug is rotated oppo-site to match. This is a factory only option.
Style II
In a Style II plug, the cable’s ground conductor is bonded to the extra grounding pole and to the plug housing via abonding jumper. The receptacle has a matching groundingpole connected to the system ground conductor which isfurther tied to the grounded conduit system via a bondingjumper. Upon insertion, detent springs in the receptaclehousing contact and ground the plug housing; then theextra long ground pole connects before the current carrying poles engage. The Style II ground pole makes firstand breaks last.
Standard S37 Option
Typical Application
3W4P Illustrated3W3P Illustrated
PR5 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR5
3 0 A M P R E C E P TA C L E S & B A C K B O X E S
CATALOG NUMBER
VERSAMATE® SERIES • PLUGS AND RECEPTACLES30 AMP NEMA 4X METALLIC
PR6
FEATURES-SPECIFICATIONS
*See page PR5 for more information on these options.
Plug
Connector
Receptacle Back Box Dimensions
• 30 Amp 600VAC/250VDC; 50-400 HertzNEMA 3, 4, 4X1
• PLUGS ONLY2 :Class I, Div. 1 & 2, Groups B,C,D; NEMA 7 B,C,DClass l, Zones 1 & 2, llB+H2, llAClass ll, Div. 1 & 2, Groups F & G; NEMA 9 F,G; Class lll
GROUND
STYLE
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
VR321E2VR331E2VR341E2VR332E2VR342E2VRE23
VR321C2VR331C2VR341C2VR332C2VR342C2
VRC23
VR321D2VR331D2VR341D2VR332D2VR342D2VRD23
VR321
VR331
VR341
VR332
VR342
–
CIRCUIT E3 TYPE
ORIG. AT
C3 TYPE
ORIG. AT
D3TYPE
ORIG. AT
RECEPTACLE ONLY
ORIG. AT
Splice box only3
330 Amp Back Boxes are available in 1/2", 3/4" and 1" conduit sizes.
Size listed for 3/4". For other available sizes, change the BOLD “2 ” in either the
assembly or box only number to: 1=1/2", 2=3/4", 3=1". Assembly catalog numbers
are listed for ease of ordering or specification and devices are shipped as compo-
nents.
3 0 A M P P L U G S & C O N N E C T O R S
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
.55 - 1 .20 IN
.55 - 1 .20 IN
.55 - 1 .20 IN
.55 - 1 .20 IN
.55 - 1 .20 IN
VP3275
VP3375
VP3475
VP3385
VP3485
GROUND
STYLECIRCUIT
GROMMET
RANGEPLUG
ORIG. AT
VPR3255
VPR3355
VPR3455
VPR3365
VPR3465
CONNECTOR
ORIG. AT
VRD
VRC
VRE
1Components are intermateable & UL classified with other UL1686 config
ured devices (when installed in accordance with instructions furnished
with device). Assemblies containing components from other manufactur
ers would have the NEMA type rating of the lowest rated device.
2Plugs are hazardous suitable when mated with properly rated receptacles
configured to use UL1686 type plugs, such as VersaMate VSQ/VBQ.
– Note, 2, 3 & 4 pole device dimensions are the same.
M O D I F I C AT I O N S *
Reverse ser v ice for receptac les , p lugs & connectors
Polar i za t ion for receptac les , p lugs & connectors
S39
S37
CATALOG NUMBER DESCRIPTION
CATALOG NUMBER
C D ReceptacleEConnector
Wire Range
Fi le No. E10757 Cer t i f i ed F i le No. LR111846
Regular S t randing: #10 - #6 or ig ina l s ty le or “AT” type
Ext ra f lex : #10 - #8 or ig ina l s ty le or “AT” type
Plug
VersaRange® clamps provide
a firm fit for one plug (or con-
nector) over a wide range of
cable diameters (competitors
often need two – requiring
additional sizing decisions).
VP3022
VP3033
VP3044
VP3023
VP3034
VPR3022
VPR3033
VPR3044
VPR3023
VPR3034
VR3022E2VR3033E2VR3044E2VR3023E2VR3034E2
VRE23
VR3022C2VR3033C2VR3044C2VR3023C2VR3034C2
VRC23
VR3022
VR3033
VR3044
VR3023
VR3034
–
VR3022D2VR3033D2VR3044D2VR3023D2VR3034D2
VRD23
Origional or AT
Terminals. See PR3 for
more information
PR6PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR666666666666666666666
VERSAMATE® SERIES • PLUGS AND RECEPTACLES60 AMP NEMA 4X METALLIC
PR7
FEATURES-SPECIFICATIONS
PRReceptacle
Plug
Connector
Back Box Dimensions
• 60 Amp 600VAC/250VDC; 50-400 Hertz NEMA 3, 4, 4X1
• PLUGS ONLY2 :Class I, Div. 1 & 2, Groups B,C,D; NEMA 7 B,C,DClass l, Zones 1 & 2, llB+H2, llAClass ll, Div. 1 & 2, Groups F & G; NEMA 9 F,G; Class lll
1Components are intermateable & UL classified with other UL1686 config-
ured devices (when installed in accordance with instructions furnished
with device). Assemblies containing components from other manufacturers
would have the NEMA type rating of the lowest rated device.
2Plugs are hazardous suitable when mated with properly rated receptacles
configured to use UL1686 type plugs, such as VersaMate VSQ/VBQ.
4Dimensions in ( ) are 3 pole devices; balance are 4 pole.
360 Amp Back Boxes are available in 1", 1-1/4" and 1-1/2" conduit sizes. Size listed
above is 1-1/4". For other available sizes, change the BOLD “4” in either the assembly
or box only number as follows: 3=1", 4=1-1/4", 5=1-1/2". Assembly catalog numbers
are listed for ease of ordering or specification and devices are shipped as components.
Note: 60 Amp receptacles also fit 100 Amp mounting boxes –
see Note4on 100 Amp page PR8.
VRC
VRE
VRD
*See page PR5 for more information on these options.
M O D I F I C AT I O N S *
Reverse ser v ice for receptac les , p lugs & connectors
Polar i za t ion for receptac les , p lugs & connectors
S39
S37
CATALOG NUMBER DESCRIPTION
Connector
VersaRange® clamps provide
a firm fit for one plug (or con-
nector) over a wide range of
cable diameters (competitors
often need two – requiring
additional sizing decisions).
Plug
4
C D ReceptacleE
Wire Range
Fi le No. E10757 Cer t i f i ed F i le No. LR111846
Regular S t randing: #6 - #2 or ig ina l s ty le or “AT” type
Ext ra f lex : #6 - #4 or ig ina l s ty le or “AT” type
6 0 A M P R E C E P TA C L E S & B A C K B O X E S
GROUND
STYLE
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
VR621E4VR631E4VR641E4VR632E4VR642E4VRE46
VR621C4VR631C4VR641C4VR632C4VR642C4
VRC46
VR621D4VR631D4VR641D4VR632D4VR642D4VRD46
VR621
VR631
VR641
VR632
VR642
–
CIRCUIT E3 TYPE
ORIG. AT
C3 TYPE
ORIG. AT
D3TYPE
ORIG. AT
RECEPTACLE ONLY
ORIG. AT
Splice box only3
CATALOG NUMBER
VR6022E4VR6033E4VR6044E4VR6023E4VR6034E4
VRE46
VR6022C4VR6033C4VR6044C4VR6023C4VR6034C4
VRC46
VR6022
VR6033
VR6044
VR6023
VR6034
–
VR6022D4VR6033D4VR6044D4VR6023D4VR6034D4
VRD46
CATALOG NUMBER
6 0 A M P P L U G S & C O N N E C T O R S
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
.65 - 1.50 IN
.65 - 1.50 IN
.65 - 1.50 IN
.65 - 1.50 IN
.65 - 1.50 IN
VP6275
VP6375
VP6475
VP6385
VP6485
GROUND
STYLECIRCUIT
GROMMET
RANGEPLUG
ORIG. AT
VPR6255
VPR6355
VPR6455
VPR6365
VPR6465
CONNECTOR
ORIG. AT
VP6022
VP6033
VP6044
VP6023
VP6034
VPR6022
VPR6033
VPR6044
VPR6023
VPR6034
6 1/2
8 13/16
Origional or AT
Terminals. See PR3 for
more information
PR7 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR7
VERSAMATE® SERIES • PLUGS AND RECEPTACLES100 AMP NEMA 4X METALLIC
PR8
FEATURES-SPECIFICATIONS
Back Box Dimensions
1Components are intermateable & UL classified with other UL1686 config-
ured devices (when installed in accordance with instructions furnished with
device). Assemblies containing components from other manufacturers would
have the NEMA type rating of the lowest rated device.
2Plugs hazardous suitable when mated with properly rated receptacles
configured to use UL1686 type plugs, such as VersaMate VBQ.
5Dimensions in ( ) are 3 pole devices; balance are 4 pole.
* Angle adapter only
3100 Amp Back Boxes are available in 1", 1-1/4", 1-1/2" & 2" conduit sizes.
Size listed above is 1-1/2". For other available sizes, change
the BOLD “5” in either the assembly or box only number as follows:
3=1", 4=1-1/4", 5=1-1/2", 6=2". Assembly catalog numbers are listed for ease of
ordering or specification and devices are shipped as components.
4100 Amp Boxes & Adapters also fit 60 Amp receptacles. Adapter only can
be used to attach receptacle at an angle to a standard sheet metal box.
VJC
E C
*See page PR5 for more information on these options.
M O D I F I C AT I O N S *
Reverse ser v ice for receptac les , p lugs & connectors
Polar i za t ion for receptac les , p lugs & connectors
S39
S37
CATALOG NUMBER DESCRIPTION
Connector
Receptacle
Plug
Connector
5
Feed through style shown
Plug
VersaRange® clamps
provide a firm fit for one
plug (or connector)
over a wide range of
cable diameters (com-
petitors often need two
– requiring additional
sizing decisions).
Receptacle
Wire Range
Fi le No. E10757 Cer t i f i ed F i le No. LR111846
Regular S t randing: #4 - #2 or ig ina l s ty le or “AT” type
Ext ra f lex : #4 - #2 or ig ina l s ty le or “AT” type
• 100 Amp 600VAC/250VDC; 50-400 Hertz NEMA 3, 4, 4X1
• PLUGS ONLY2 :Class I, Div. 1 & 2, Groups B,C,D; NEMA 7 B,C,DClass l, Zones 1 & 2, llB+H2, llAClass ll, Div. 1 & 2, Groups F & G; NEMA 9 F,G; Class lll
CATALOG NUMBER
1 0 0 A M P P L U G S & C O N N E C T O R S
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
.88 - 1 .68 IN
.88 - 1 .68 IN
.88 - 1 .68 IN
.88 - 1 .68 IN
.88 - 1 .68 IN
VP10277
VP10377
VP10477
VP10387
VP10487
GROUND
STYLECIRCUIT
GROMMET
RANGEPLUG
ORIG. AT
VPR10257
VPR10357
VPR10457
VPR10367
VPR10467
CONNECTOR
ORIG. AT
VP1022
VP1033
VP1044
VP1023
VP1034
VPR1022
VPR1033
VPR1044
VPR1023
VPR1034
1 0 0 A M P R E C E P TA C L E S & B A C K B O X E S
GROUND
STYLE
Sty le I
S ty le I I
2W2P
3W3P
4W4P
2W3P
3W4P
VR1021E5VR1031E5VR1041E5VR1032E5VR1042E5
VJ57
VR1021C5VR1031C5VR1041C5VR1032C5VR1042C5
VJC57
VR1021
VR1031
VR1041
VR1032
VR1042
VJA100*
CIRCUIT E3 TYPE
ORIG. AT
C3TYPE
ORIG. AT
RECEPTACLE ONLY
ORIG. AT
Splice box only3
CATALOG NUMBER
VR1022E5VR1033E5VR1044E5VR1023E5VR1034E5
VJ57
VR1022
VR1033
VR1044
VR1023
VR1034
VJA100*
VR1022C5VR1033C5VR1044C5VR1023C5VR1034C5
VJC57
Origional or AT
Terminals. See PR3 for
more information
PR8PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR88888888888888888888
VERSAMATE® SERIES • PLUGS AND RECEPTACLES200 AMP NEMA 4X METALLIC
PR9
FEATURES-SPECIFICATIONS
PRReceptacle
Connector
Back Box Dimensions
2 0 0 A M P P L U G S & C O N N E C T O R S
Sty le I
S ty le I I
3W3P
4W4P
2W3P
3W4P
1.0 - 2 .5 IN
1.0 - 2 .5 IN
1.0 - 2 .5 IN
1.0 - 2 .5 IN
VP203512
VP204513
VP203612
VP204612
GROUND
STYLECIRCUIT
GROMMET
RANGE PLUG
CATALOG NUMBER
VPR203112
VPR204113
VPR203212
VPR204212
CONNECTOR
1 Components are intermateable & UL classified with Appleton®
Powertite® or Crouse-Hinds® Arktite® devices (when installed in
accordance with instructions furnished with device. Assemblies con
taining components from other manufacturers would have the NEMA
type rating of the lowest rated device.
4 Dimensions in ( ) are 3 pole devices; balance are 4 pole.
5 200A 3W4P Reverse Service configured “W” Series and VersaMate®
are not intermateable. However, the VersaMate VR20422-S39 recepta-
cle ships with instructions to permanently convert for use with existing
PW-6402X SU39 plugs. Factory only configured plugs to fit old RW64C-
SU39 receptacles may be ordered as VP-PW64026 SU39.
200 Amp Back Boxes are available in dead-end sizes 1-1/2",
2" & 2-1/2" conduit sizes. Dead-end box shown is 2". For other available
dead-end box sizes, change the BOLD “6” in either the dead-end assembly
or box only number as follows: 5=1-1/2", 6=2", 7=2-1/2". Feed through boxes
are available in 2-1/2"; use “R” series adapters as required for smaller sizes
(sold separately). Assembly catalog numbers are listed for ease of ordering
or specification and devices are shipped as components.
Adapter only can be used to attach receptacle at an angle to a standard
sheet metal box.
NOTE: 200A VersaMate receptacle lids secure with wingnuts for N4X environ-
ments when not in use. VersaMate plugs secure with wingnuts and/or
lock-ring collar. This exclusive dual method allows retention of competi-
tive plugs that use either wingnuts or a lock-ring collar.
ReceptacleCE
VJC
*See page PR5 for more information on these options.
M O D I F I C AT I O N S *
Reverse ser v ice for receptac les , p lugs & connectors
Polar i za t ion for receptac les , p lugs & connectors
S395
S37
CATALOG NUMBER DESCRIPTION
2 0 0 A M P R E C E P TA C L E S & B A C K B O X E S
GROUND
STYLE
Sty le I
S ty le I I
3W3P
4W4P
2W3P
3W4P
VR20312E6VR20412E6VR20322E6VR20422E6
VJ68
VR20312C7VR20412C7VR20322C7VR20422C7
VJC78
VR20312
VR20412
VR20322
VR20422
Angle adapter
only VJA200
CIRCUIT E2TYPE
C2TYPE
RECEPTACLE
ONLY
Spl ice box only
w/adapter23
CATALOG NUMBER
200 Amp 600VAC/250VDC; 50-400hertz NEMA 3 4, 4X1
VersaRange®
clamps provide a
firm fit for one plug
(or connector) over
a wide range of
cable diameters
(competitors often
need two – requir-
ing additional sizing
decisions).
Plug
Wire Range
Fi le No. E10757 Cer t i f i ed F i le No. LR111846
E213215
Regular S t randing: #1 - 250
Ext ra f lex : #1 - 250
( .653 max conductor d iameter )
Plug Connector
2
3
4
ALLENTERMINALS
PR9 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR9
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVSQ & VWSQ INTERLOCKED SWITCHED RECEPTACLES
PR10
FEATURES-SPECIFICATIONS
V S Q & V W S Q R E C E P TA C L E S
• VSQ Hazardous Location RatingsClass I, Div. 1 & 2, Groups B,C,DClass I, Zones I & 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F & G Class lllNEMA 3, 4, 4X, 7 (B,C,D), 9 (F,G)
VersaMate VSQ & VWSQ Receptacles use
VersaMate Style II plugs found on pages PR6 & PR7
and are compatible with appropriately configured
Crouse-Hinds® Arktite® or Appleton® Powertite®
plugs (when installed in accordance with instruc-
tions furnished with device)
Arktite® is a registered trademark of Crouse-Hinds®.
Powertite® is a registered trademark of Appleton®.
Features• N4X with receptacle lid turned shut
or with plug locking ring tightened
• Copper-free aluminum constructionwith electrostatically applied poly-ester/epoxy finish. Handle mecha-nism is chemical resistant Valox®
(TM General Electric).
• Compact size and footprint
• Plug Interlock Mechanism for Dead-front construction. Switch cannot beturned “ON” without fully insertedplug. Plug cannot be removed withswitch in “ON” position
• Plug held in place when switch is“Off” for convenience. Pull operatedrelease mechanism. Plug and wiringdo not have to be twisted or held tooperate switch
• Factory Wired Receptacle; easy towire line side of switch
• Easily visible “On-Off” indicator handle
• “Off” position is padlockable formaintenance safety
• Auxiliary Contact (late-make early-break)
contact rated 10 Amp, 1/3 HP at 125/250
VAC. Can be used for operating pilot
lights or starter coils (standard model only)
• Feed-through construction
• Horsepower Rated
• Internal switch horsepower rated as “motor disconnect”
HORSEPOWER120 240 480 600
RATINGS (VAC)1
1Ø 2 5 10 15
3Ø 3 7.5 15 20
1Ø – 10 15 20
3Ø – 10 25 30
30A
60A
NOTES: VSQ/VWSQ 30 Amp models come standard with 1" drilled and tapped conduit openings
top and bottom plus two 1" x 3/4" reducers and one 3/4" close-up plug for maximum flexibility.
60 amp models come with 1-1/2" openings top and bottom and one 1-1/2" close-up plug.
VSQ & VWSQ Receptacle covers are NOT interchangeable.
1Refers to internal switch only.
VSQ HAZARDOUS VWSQ N4X ONLY VERSAMATE PLUG
302W3P VSQ3023 VWSQ3023 VP3385
3W4P VSQ3034 VWSQ3034 VP3485
602W3P VSQ6023 VWSQ6023 VP6385
3W4P VSQ6034 VWSQ6034 VP6485
CATALOG NUMBER
AMPS CIRCUIT
*See page PR5 for more information on this option
M O D I F I C AT I O N S *
Polar i za t ion for
receptac les , p lugs S37
CATALOG NUMBER DESCRIPTION
V S Q & V W S Q R E C E P TA C L E S
Fi le No. LR14667
Fi le No. E91049
• VWSQ for Wet & Corrosive LocationsNEMA 3, 4, 4X
Wire Range
30 Amp Regular S t randing Max #10
60 Amp Regular S t randing Max #4
Dimensions shown are in inches for 30 AMP: 60 Amp dimensions in ( ).
NOTES: Devices have adjustable ductile lugs (vertical or side) for attachment to uneven surfaces.
Ordinary twist type wire connectors are used for final connections on 30A,
60A devices have terminal blocks.
Dimensions
VSQ
VWSQ
PR10PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111111111111111111111111100000000000000000000
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVSQ-FS FACTORY SEALED INTERLOCKED SWITCHED RECEPTACLE
PR11
FEATURES-SPECIFICATIONS
PR
Class I, Div. 1 & 2, Groups B,C,DClass I, Zones I & 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F & G Class lllNEMA 3, 4, 4X, 7 (B,C,D), 9 (F,G)
Dimensions shown are in inches for 30 AMP. 60 AMP Dimensions in ( ).
Features – same as VSQ1 plus:• Factory Sealed Construction elimi-
nates need for conduit sealing at the device
• Saves Installation Time & Labor –facilitates rework
• Switch has factory wired line andload terminals. Load terminals feedsealed receptacle as in a standardVSQ. Line wiring is passed from thesealed compartment into the wiringchamber
• Receptacles may be loosened fromblack box and turned 180 degrees toadjust for top or bottom feed.
• Ordinary twist type wire connectorsare used for final connections on30A. 60A devices have terminalblocks
NOTES: VSQ-FS 30 Amp models come standard
with one 1" drilled and tapped conduit openings
into the wiring chamber plus one 1" x 3/4"
reducer.
60 amp models come with one 1" opening.
1VSQ-FS models do not have auxiliary contacts.
VSQ-FS VERSAMATE
HAZARDOUS PLUG
30 2W3P VSQ3023FS VP3385
30 3W4P VSQ3034FS VP3485
60 2W3P VSQ6023FS VP6385
60 3W4P VSQ6034FS VP6485
V S Q - F S R E C E P TA C L E S
Dimensions
*See page PR5 for more information on this option.
M O D I F I C AT I O N S *
Polarizat ion for receptacles
& plugs S37
CATALOG NUMBER DESCRIPTION
CATALOG NUMBER
AMPS CIRCUIT
Fi le No. E91049
Cer t i f i ed F i le No. LR14667
Wire Range
30 Amp Regular S t randing Max #10
60 Amp Regular S t randing Max #4
PR11 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111111
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVBQ BREAKER PROTECTED INTERLOCKED RECEPTACLES600VAC/250VDC
PR12
FEATURES-SPECIFICATIONS
VersaMate VBQ Receptacles use VersaMate
Style II plugs found on 30, 60 and 100 amp pages
and are compatible with appropriately configured
Crouse-Hinds® Arktite® or Appleton® Powertite®
plugs (when installed in accordance with instruc-
tions furnished with device).
Arktite® is a registered trademark of Crouse-Hinds®.
Powertite® is a registered trademark of Appleton®.
Receptacle:
• N4X with receptacle lid turned shutor with plug locking ring tightened
• Plug held in place when switch is“Off” for convenience. Pull buttonoperated release mechanism. Plugdoes not have to be twisted to oper-ate switch
• Dead-front construction when recep-tacle is off. Switch cannot be turned“ON” without fully inserted plug. Plugcannot be removed with switch in“ON” position
• Wire Connections do not bend whenopening and closing door – minimizesloosening during installation or maintenance procedures
Features
Dimensions
Enclosure:
• Spacious wiring room. Meets the latest NEC wire bending require-ments for circuit breaker enclosures
• Ductile Mounting Lugs to adjust touneven surfaces
• Copper-free construction with 316grade Stainless Steel ExternalHardware
• Quick Release Cover Bolts with TripleLeads – only 3-1/2 turns to disengage
• Recessed Flange Notches – Allowseasier cover opening with pryinginstrument without flange damage
• Aluminum lacquer paint finish for cor-rosion resistance
• Visible “ON” external Breaker Handlehas provisions for locking “ON” or“OFF” with up to three Padlocks
• Internal Lock-Off provision for main-tenance when no hazardous materi-als are present
Fi le No. E184637
Receptacle assembly
is field replaceable for
maintenance.
Ordering information listed
in the instruction sheets
provided with the product.
Class I, Div. 1 & 2, Groups B,C,DClass I, Zones I & 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F & G Class lllNEMA 3, 4, 4X, 7 (B,C,D), 9 (F,G)
Note: The VBQ series is B7EC enclosure
based. See page E-13 for additional
dimensional information.
Replacement Parts:
• Enclosure gasket VBQ-535
• External handle kit CBHK-100H
See instruction sheet included with device for other available replace-ment parts.
PR12PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR111111111111111111111111111111111111111111111111111111111111111111111111111111222222222222222222222
M O D I F I C AT I O N S1
Internal Lock-Off
provision for
maintenance when
no hazardous
materials are present
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVBQ BREAKER PROTECTED INTERLOCKED RECEPTACLES600VAC/250VDC
PR13
FEATURES-SPECIFICATIONS
PR
Circui t Breaker Wire Range
Square D To 30 Amp #14-4 cu. ; 35-100 Amp #14-1/0 cu .
Cut le r-Hammer To 20 Amp #14-10 cu. ; 30-100 Amp #14-1/0 cu .
Consult Breaker Manufacturer literature for Horsepower Ratings.
†DC ra t ings apply to substan t ia l ly non- induct ive c i rcu i ts .
*Pending breaker s ty le change.
RECEPTACLE CIRCUIT BREAKER
CATALOG NUMBER
Polar izat ion for receptacles & plugs
Dra in
Brea ther
Dra in and Brea ther (CSA Groups C & D)
S37
SU10
SU11
SU3
CATALOG NUMBER DESCRIPTION
1See page PR5 and price sheet for more information on these options.
V B Q R E C E P TA C L E S
SQUARE D SQUARE D CUTLER-HAMMER CUTLER-HAMMER VERSAMATE
FAL (480 VAC MAX.) FHL (600 VAC MAX.) EHD (480 VAC MAX.) FD (600 VAC MAX.) PLUG
20 VBQ3023SN20 VBQ3023SH20 VBQ3023CN20 VBQ3023CH20 VP3385
30 VBQ3023SN30 VBQ3023SH30 VBQ3023CN30 VBQ3023CH30 VP33852W3P
40 VBQ3023SN40 VBQ3023SH40 VBQ3023CN40 VBQ3023CH40 VP3385
3050 VBQ3023SN50 VBQ3023SH50 VBQ3023CN50 VBQ3023CH50 VP3385
20 VBQ3034SN20 VBQ3034SH20 VBQ3034CN20 VBQ3034CH20 VP3485
30 VBQ3034SN30 VBQ3034SH30 VBQ3034CN30 VBQ3034CH30 VP34853W4P
40 VBQ3034SN40 VBQ3034SH40 VBQ3034CN40 VBQ3034CH40 VP3485
50 VBQ3034SN50 VBQ3034SH50 VBQ3034CN50 VBQ3034CH50 VP3485
50 VBQ6023SN50 VBQ6023SH50 VBQ6023CN50 VBQ6023CH50 VP6385
60 VBQ6023SN60 VBQ6023SH60 VBQ6023CN60 VBQ6023CH60 VP6385
2W3P 70 VBQ6023SN70 VBQ6023SH70 VBQ6023CN70 VBQ6023CH70 VP6385
90 VBQ6023SN90 VBQ6023SH90 VBQ6023CN90 VBQ6023CH90 VP6385
100 VBQ6023SN100 VBQ6023SH100 VBQ6023CN100 VBQ6023CH100 VP638560
50 VBQ6034SN50 VBQ6034SH50 VBQ6034CN50 VBQ6034CH50 VP6485
60 VBQ6034SN60 VBQ6034SH60 VBQ6034CN60 VBQ6034CH60 VP6485
3W4P 70 VBQ6034SN70 VBQ6034SH70 VBQ6034CN70 VBQ6034CH70 VP6485
90 VBQ6034SN90 VBQ6034SH90 VBQ6034CN90 VBQ6034CH90 VP6485
100 VBQ6034SN100 VBQ6034SH100 VBQ6034CN100 VBQ6034CH100 VP6485
50 VBQ1023SN50 VBQ1023SH50 VBQ1023CN50 VBQ1023CH50 VP10387
70 VBQ1023SN70 VBQ1023SH70 VBQ1023CN70 VBQ1023CH70 VP103872W3P
90 VBQ1023SN90 VBQ1023SH90 VBQ1023CN90 VBQ1023CH90 VP10387
100 VBQ1023SN100 VBQ1023SH100 VBQ1023CN100 VBQ1023CH100 VP10387100
50 VBQ1034SN50 VBQ1034SH50 VBQ1034CN50 VBQ1034CH50 VP10487
70 VBQ1034SN70 VBQ1034SH70 VBQ1034CN70 VBQ1034CH70 VP104873W4P
90 VBQ1034SN90 VBQ1034SH90 VBQ1034CN90 VBQ1034CH90 VP10487
100 VBQ1034SN100 VBQ1034SH100 VBQ1034CN100 VBQ1034CH100 VP10487
Fi le No. E184637
Class I, Div. 1 & 2, Groups B,C,DClass I, Zones I & 2, IIB+H2, IIAClass II, Div. 1 & 2, Groups F & G Class lllNEMA 3, 4, 4X, 7 (B,C,D), 9 (F,G)
Circui t Breaker 208/240 480 VAC 600 VAC 250 VDC†
In ter rupt ing Ra t ings VAC
Square D FAL(HDL*) 25,000 18,000 —— 10,000
Square D FHL(HGL*) 65,000 25,000 18,000 10,000
Cut le r-Hammer EHD 18,000 14,000 —— 10,000
Cut le r-Hammer FD 65,000 25,000 18,000 10,000
PR13 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111113
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVSI NON-METALLIC PLUGS AND SWITCHED RECEPTACLES
PR14
FEATURES-SPECIFICATIONS
Class I, Div. 2, Groups A,B,C,DClass I, Zones 1 & 2, Groups llC, llB, llA
AEx de IIC T6Class II, Div. 1 & 2, Groups E,F,GClass IIINEMA 3, 4, 4X, IP66
FM
APPROVED
Cer t i f i ed - F i le LR240743
See f i les for de ta i ls or ca l l K i l la rk
F i le 3014299
CATALOG NUMBER
2 Pole
3 Wire
3 Pole
4 Wire
4 Pole
5 Wire
Applications• For use in hazardous and corrosive
environments such as refineries,chemical plants, water treatment andbio gas plants, and wherever a com-bustible gas-air mixture or com-bustible dust may occur
Features• Color coding and pin configuration
makes it physically impossible tomate plugs and receptacles of different voltages and current ratings
• Interlocked switch mechanism prevents accidental removal of plugfrom receptacle under load
• Horsepower rated disconnect switch
• Dust caps* included with 20A and30A plugs as standard
• No seal required within Class I, Division2 applications.
• Provision for up to two optional auxilliarycontact blocks, useful for signaling cir-cuits or starter coils.3
• Dimensional information - page PR16.
V S I S E R I E S P L U G S & S W I T C H E D R E C E P TA C L E S
T E C H N I C A L D ATA
AC VOLTAGE AND
COLOR CODE
125 Yellow
250 Blue
480 Red
3 Ø 250 Blue
3 Ø 480 Red
3 Ø 600 Black
3 ØY 120/208 Blue
3 ØY 277/480 Red
3 ØY 347/600 Black
DESCRIPTION
RECEPTACLE
VSI20R304
VSI20R306
VSI20R307
VSI20R409
VSI20R407
VSI20R405
VSI20R509
VSI20R507
VSI20R505
PLUG
VSI20P304
VSI20P306
VSI20P307
VSI20P409
VSI20P407
VSI20P405
VSI20P509
VSI20P507
VSI20P505
PLUG
—
—
—
VSI30P409
VSI30P407
VSI30P405
VSI30P509
VSI30P507
VSI30P505
RECEPTACLE
—
—
—
VSI30R409
VSI30R407
VSI30R405
VSI30R509
VSI30R507
VSI30R505
30 AMP220 AMP1
PARTS AND ACCESSORIES3
Auxiliary Contact Block NC, A6004
Auxiliary Contact Block NO, A6004
PART NUMBER
VSIAUXNC
VSIAUXNO
410A rating for one auxiliary block; 5A if two are
used. Position noted (NC or NO) is when main
switch is off.
Snap into side(s) of terminal block
RECEPTACLE
ENCLOSURE MATERIAL
AMBIENT TEMPERATURE,Ta
TERMINAL CAPACITY
SWITCH RATING (HORSEPOWER)
120 VAC
240 VAC
480 VAC
600 VAC
LINE SUPPLY FUSE
BOTTOM ENTRY
POLYAMIDE
-30°C (-22°F) TO +55°C (131°F)
2 wires, rated 75°C (Ta<45°C) or 90°C (Ta>45°C)
CLASS J - size per NEC/CEC requirement
20 AMP
16-10 AWG
3/4” NPT
30 AMP
14-8 AWG
3-phase
—
10 HP
20 HP
25 HP
1” NPT
1-phase
1.5 HP
3 HP
5 HP
3-phase
—
5 HP
10 HP
15 HP
T E C H N I C A L D ATA
PLUG
ENCLOSURE MATERIAL
TERMINAL CAPACITY
CORD OUTER DIA.
POLYAMIDE
1 wire, rated 75°C (Ta<45°C) or 90°C (Ta>45°C)
20 AMP
16-10 AWG
0.3” - 0.8”
30 AMP
14-8 AWG
0.6” - 1.1”
1VSI 20A devices are compatible with prior 16A models. However, the rating of the loweramperage will apply.
2VSI 30A devices are compatible with prior 32A models. Ratings of the lower amperagewill apply.
* Dust caps shall be installed on plugs with receptacle cover closed when the plug is not engaged in the receptacle.
PR14PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR111111111111111111111111111111111111111111111111111111111111111111111111111111444444444444444444444
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVSI NON-METALLIC PLUGS AND SWITCHED RECEPTACLES
PR15
PR
FEATURES-SPECIFICATIONS
Class I, Div. 2, Groups A,B,C,DClass I, Zones 1 & 2, Groups llC, llB, llA
AEx de IIC T6Class II, Div. 1 & 2, Groups E,F,GClass IIINEMA 3, 4, 4X, IP66
FM
APPROVED
Dust cap shall be installed on the plug when
the plug is not engaged in the receptacle.
P L U G D U S T C A P
FOR PLUG TYPE CATALOG NUMBER
VSI63P4__ VSI63801140
VSI63P5__ VSI63801140
VSI125P4__ VSI125801140
VSI125P5__ VSI125801140
CATALOG NUMBER
63 AMP 125 AMP
3 Pole
4 Wire
4 Pole
5 Wire
V S I S E R I E S P L U G S & S W I T C H E D R E C E P TA C L E S
AC VOLTAGE AND
COLOR CODE
3 Ø 250 Blue
3 Ø 480 Red
3 Ø 600 Black
3 ØY 120/208 Blue
3 ØY 277/480 Red
3 ØY 347/600 Black
DESCRIPTION
PLUG
VSI63P409
VSI63P407
VSI63P405
VSI63P509
VSI63P507
VSI63P505
RECEPTACLE
VSI63R409
VSI63R407
VSI63R405
VSI63R509
VSI63R507
VSI63R505
PLUG
VSI125P409
VSI125P407
VSI125P405
VSI125P509
VSI125P507
VSI125P505
RECEPTACLE
VSI125R409
VSI125R407
VSI125R405
VSI125R509
VSI125R507
VSI125R505
Applications• For use in hazardous and corrosive
environments such as refineries,chemical plants, water treatment andbio gas plants, and wherever a com-bustible gas-air mixture or com-bustible dust may occur
• When VSI Series is installed in ClassII Div. 1 & 2 locations, dust caps forplugs are required. See orderinginformation below
Features• Color coding and pin configuration
makes it physically impossible tomate plugs and receptacles of different voltages and current ratings
• No seals required within Class I, Div.2 applications
• Interlocked switch mechanism prevents accidental removal of plugfrom receptacle under load
• Horsepower rated disconnect switchincludes 1 auxiliary contact (latemake, early break) for signaling cir-cuits.
• 63A, 125A models
Dimensional Information• See page PR16
VSI non-metallic devices NOT intermateable with Versamate® NEC metallic series.
T E C H N I C A L D ATA
RECEPTACLE
ENCLOSURE MATERIAL
AMBIENT TEMPERATURE,Ta
TERMINAL CAPACITY
SWITCH RATING (HORSEPOWER)
120 VAC
240 VAC
480 VAC
600 VAC
LINE SUPPLY FUSE
BOTTOM ENTRY
FIBER REINFORCED POLYESTER
-20°C (-4°F) TO +40°C (104°F)
2 wires, 90°C rated
CLASS J - size per NEC/CEC requirement
63 AMP
6-1/0 AWG
3-phase
10 HP
20 HP
40 HP
60 HP
1-1/2” NPT
125 AMP
1/0-3/0 AWG
3-phase
20 HP
40 HP
100 HP
125 HP
2” NPT
T E C H N I C A L D ATA
PLUG
ENCLOSURE MATERIAL
TERMINAL CAPACITY
CORD OUTER DIA.
POLYAMIDE
1 wire, 90°C rated
63 AMP
10-4 AWG
0.94” - 1.4”
125 AMP
6-1/0 AWG
1.2” - 2”
Cer t i f i ed - F i le LR240743
See f i les for de ta i ls or ca l l K i l la rk
F i le 3014299
PR15 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111115
VSI NON-METALLIC PLUGS AND SWITCHED RECEPTACLESPR1613
.5”(
34
2 m
m)
RECEPTACLE & PLUG 63A
3 POLE - 4 WIRE AND 4 POLE - 5 WIRE RECEPTACLE & PLUG 125A
3 POLE - 4 WIRE AND 4 POLE - 5 WIRE
.35
”(9
mm
)
.35”(9 mm)6”
(152 mm)
7.1”(180 mm)
.51
”(1
3 m
m)
16”(407 mm)
8.3”(211 mm)
19.4
”(4
93
mm
)
.43
”(11
mm
)
.43”(11 mm)8.7”
(220 mm)
10.7”(270 mm)
.8”
(20
.5 m
m)
21.8”(553 mm)
12.0”(296 mm)
4.1” (104 mm)
4.9”
(12
5 m
m)
.24
”(6
mm
)
(6 mm)
9.8
” (2
48
mm
)
6.2
5”
(15
9 m
m)
.47” (12 mm)
7.12” (181 mm)
4.0” (103 mm)
3.7” (94 mm)
4.5
2”
(115
mm
).2
4”
(6 m
m)
5.9
” (1
50
mm
)
.47” (12 mm)
6.6” (168 mm)
.24”
(6 mm)
3.66” (93 mm)
4.13” (105 mm)
9.1
3”
(23
2 m
m)
.24”
O.D. 3” (76 mm)
6.9”
(17
6 m
m)
O.D. 2.4”(60 mm)
RECEPTACLE 20A
2 POLE - 3 WIRE
PLUG 20A RECEPTACLE 20A
3 POLE - 4 WIRE AND 4 - POLE 5 WIRE
4.9” (124 mm)
5.9
” (1
50
mm
).2
4”
(6 m
m)
.47” (12 mm)
8.15” (207 mm)
.24”
(6 mm)
4.8” (123 mm)
5.3” (135 mm)
11.1
” (2
81
mm
)
O.D. 3.9” (99 mm) - 4 WireO.D. 4” (102 mm) - 5 Wire
8.03
” (20
4 m
m)
O.D. 2.8”(72 mm)
RECEPTACLE 30A
3 POLE - 4 WIRE AND 4 POLE - 5 WIRE PLUG 30A
Dimensions
NOTE: Drawings are not to scale
10.6”(268.5 mm)
4.4”(112 mm)
2.7”(69.5 mm)
3.3
” (8
4 m
m)
4.9”(125 mm)
3.2”(82 mm)
12.2”(310.5 mm)
3.8
” (9
6 m
m)
4.5” (115 mm)7.
4” (
188
mm
)
PR16PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR111111111111111111111111111111111111111111111111111111111111111111111111111111666666666666666666666
VERSAMATE® SERIES • PLUGS AND RECEPTACLESVCR CLEAN ROOM RECEPTACLES
PR17
FEATURES-SPECIFICATIONS
PR
Suitable for:
Class I, Div. 2, Groups A,B,C,DClass I, Zones 1 & 2, Groups IIC, IIB, IIAClass II, Div. 1 & 2, Groups E,F,GClass IIINEMA 3CENELEC-EEx de IIC T6 IP54
Applications• Designed specifically for hazardous
location clean rooms, such as foundin the pharmaceutical industry,where equipment must be easy toclean and free of contaminant hold-ing cavities. Electrical devicesshould also be flush wall mounted,with concealed wiring, to minimizecontamination.
• VSI20P and VSI30P series plugsinclude debris caps, which are re-quired in Class II Div.1 and 2 locations.
Features • Available with single or duplex
receptacles, in 16 or 32 amps with a variety of voltage and pin configurations 2
• Flush mounting, smooth contours for easy cleaning
• Hazardous locations suitability
• Enclosure made of stainless steelwith concealed EPDM gasketing
• Cover is hinged on left side.Provides access with loosening of 2screws
• Color coding and pin configuration iscompliant to IEC 60309-2.
• Interlocked switch mechanism pre-vents accidental removal of plugfrom receptacle under load.
• Explosion protected disconnectswitch requires protection by Class“J” fuse (upstream), 20A max. for16A receptatcle, 40A max. for 32Areceptacle.
CATALOG NUMBER
2 Pole
3 Wire
3 Pole
4 Wire
4 Pole
5 Wire
V C R S E R I E S C L E A N R O O M R E C E P TA C L E S
AC VOLTAGE AND
COLOR CODE
125 Yellow
250 Blue
480 Red
3 Ø 250 Blue
3 Ø 480 Red
3 Ø 600 Black
3 ØY 120/208 Blue
3 ØY 277/480 Red
3 ØY 347/600 Black
DESCRIPTION
I I 2G EEx ed I IC T5/T6, IP65
PTB No. 01 ATEX 1001
—
—
—
VCR32R409
VCR32R407
VCR32R405
VCR32R509
VCR32R507
VCR32R505
OFF
ON
VSI20P304
VSI20P306
VSI20P307
VSI20P409
VSI20P407
VSI20P405
VSI20P509
VSI20P507
VSI20P505
VCR16R304
VCR16R306
VCR16R307
VCR16R409
VCR16R407
VCR16R405
VCR16R509
VCR16R507
VCR16R505
—
—
—
VSI30P409
VSI30P407
VSI30P405
VSI30P509
VSI30P507
VSI30P505
32 AMP116 AMP1
RECEPTACLE PLUG2 RECEPTACLE PLUG2
1VCR catalog numbers shown in table are for SINGLE receptacles. For duplex units, add second
receptacle configuration to catalog number.
Example: VCR32R409-16R304
Left Receptacle Position
Right
Receptacle Position
Single/DuplexReceptacleProfile
SingleReceptacle
DuplexReceptacle
Duplex Receptacle
220A plugs fit 16A receptacles; 30A plugs fit 32A receptacles.
VCR non-metallic plugs NOT intermateable with VersaMate® NEC metallic series.
PR17 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111117
KR SERIES • PLUGS AND RECEPTACLESHAZARDOUS LOCATION - DELAYED ACTION
PR18
FEATURES-SPECIFICATIONS
Lis ted E23572
Cer t i f i ed LR146671
Class I, Div. 1 & 2, Groups C,DClass l, Zones 1 & 2, llB,llANEMA 7 (C,D)
E L E C T R I C A L R AT I N G S
ApplicationsKR Series plugs and receptacles aresuitable:
• In hazardous locations due to the presence of flammable vapors orgases
• Where a heavy duty plug and recep-tacle is necessary
• Where a connection is required for portable or movable equipment suchas tools, motors, hand lights, etc.
• KP series plugs use solder termina-tions for sure connection
• KR series receptacles use wire leadsfor termination
Features• Factory sealed receptacles
• Copper free aluminum
• Straight or angle type receptacles
• Delayed action contacts (See TimeDelay Inset)
• Plugs with a wide range of grommetopenings
• Extra long grounding pole makescontact first and breaks contact last
• Heavy duty construction to withstandrough and constant usage
SelectionRefer to page headings for suitability ofspecific items. When selecting a Killarkdevice consider the following:
(A) Installation area (Hazardous orWeather-Resistant)
(B) Amperage
(C) Voltage
(D) Electrical Rating (see below)
(E) Grounding
(G) Modifications (see right)
(H) Mounting arrangement
(I) Box and hub type
(J) Cord diameter
Details of SafetyTime Delay Feature
The key slot provided in the receptacleengages the key of the plug permittingentrance of the plug in the receptaclein only one position. See steps 1-4.
The contacts are enclosed in longaccurate insulating cavities. It is inthese cavities that the arcs are extin-guished. All contacts are made throughround tellurium copper tubing which isextra heavy to withstand arcing asrequired on the various ampere ratings.
Both plugs and receptacles areequipped with an extra long groundingpole which establishes groundingbefore the power contacts areengaged. These grounding poles arealso the last to break contact. Thisassures bonding of the portable deviceto the electrical conduit system.
Selection
Modifications are available by adding
the following suffix to the catalog num-
ber. (Note: It must be added to both
the plug and the receptacle so they
will mate.)
TYPE AMPERAGE VOLTAGE VAC CIRCUIT H.P. HERTZ
120 AMP 20 115/230 2W3P 1 60
7 460 2W3P 1/2 60
7 460 3W4P 1 6030 AMP
30 115/230 2W3P 1-1/2 60
30 115/230 3W4P 3 60
30 460 2W3P 3 60
30 460 3W4P 5 6060 AMP
60 115/230 2W3P 5 60
60 115/230 3W4P 5 60
Safety Time Delay Feature
M O D I F I C AT I O N S
In te r ior contac t assem-
bl ies a re to be ro ta ted 22-
1/2° to the r igh t .
SU37
In te r ior contac t assem-
bl ies a re to be ro ta ted
22-1/2° to the le f t .
SU38
CATALOG NUMBER DESCRIPTION
Plug then can be moved
completely in and be energized
Receptacle Keyway
Key Plug
Plug can move in only to the
first step of the keyway until...
Align Keyway on plug with receptacle.
1
2
3
4
...key is moved up
1CSA approval on 20 Amp only.
PR18PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111111111111111111111111188888888888888888888
KR SERIES • PLUGS AND RECEPTACLES20 AMP/115/230 V.A.C. • 1Ø 2 WIRE, 3 POLE
PR19
FEATURES-SPECIFICATIONS
PR
K R J R E C E P TA C L E W I T H A J O R J L B O X
K R S 2 0 A 1 Ø 2 W R E C E P TA C L E W I T H S W B B O X2
E L E C T R I C A L R AT I N G
Lis ted F i le No. E23572
Cer t i f i ed F i le No. LR14667
CIRCUIT RATING (60 HERTZ)
1Ø 20 AMPS 115/230 V.A.C. 1 H.P.
2W3P
CATALOG NUMBER
KRS Series KRA
CATALOG NUMBER
AJC JLC JLX
— KRJC-120 KRJX-120
KRAJC-220 KRJC-220 KRJX-220
KRAJC-320 — —
HUB
SIZE
1/2"
3/4"
1"
HUB
SIZE
1/2"
3/4"
1"
K P 2 0 A M P P L U G
CATALOG NO. DESCRIPTION
Plug furn ished wi th KP-20ABC
3 grommets range .250 - .625
KRS-Series
B A C K B O X O N LY
1/2" — JLC-1 JLX-1
3/4" AJC-2 JLC-2 JLX-2
1" AJC-3 — —
RECEPTACLE ONLY - CATALOG NUMBER KRJ-20
JL Series boxes shown on page F60. Refer to page headings for suitability of
specific items.
See page PR18 for available polarization options.
Plug
RECEPTACLE ONLY - CATALOG NUMBER KRS-20
1KRS Series receptacles - Class I, Group D.
2SWB Series mounting splice boxes only for receptacles shown above listed on page C19.
See page PR18 for available polarization options.
AJC JLXJLC
KRJ-Series
See page PR18 for available polarization
options.
SINGLERECEPTACLE &DEAD END BOX
BOX
ONLY
SINGLERECEPTACLE &FEED-THRU BOX
BOX
ONLY
KRS-215-120
KRS-215-220
KRS-215-320
SWB-1
SWB-2
SWB-3
SWB-4
SWB-5
SWB-6
KRS-218-120
KRS-218-220
KRS-218-320
DOUBLERECEPTACLE &DEAD END BOX
BOX
ONLY
DOUBLERECEPTACLE &FEED-THRU BOX
2KRS-215-120
2KRS-215-220
2KRS-215-320
SWB-7
SWB-8
SWB-9
BOX
ONLY
SWB-10
SWB-11
SWB-12
2KRS-218-120
2KRS-218-220
2KRS-218-320
Class I, Div. 1 & 2, Groups C,D1Class l, Zones 1 & 2, llB,llANEMA 7 (C,D)
PR19 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR11111111111111111111111111111111111111111111111111111111119
KR SERIES • PLUGS AND RECEPTACLES30 AMP 115/230 V.A.C. 7 AMP 460 V.A.C.
PR20
FEATURES-SPECIFICATIONS
Class I, Div. 1 & 2, Groups C,D1Class I, Zones 1 & 2, llB, llANEMA 7 (C,D)
Lis ted - F i le E23572
See f i les for de ta i ls or ca l l K i l la rk .
KRS/KRJ SERIES PLUG
KRA SeriesKRS Series Plug
K R J R E C E P TA C L E W I T H A J O R J L B O X
K P 3 0 A M P P L U G
CATALOG NUMBER
1Ø, 2-WIRE, 3Ø, 3-WIRE PLUG GROMMET
3-POLE 4-POLE TYPE RANGE
KP-303D23 KP-304D23 D .375- .625
KP-303D45 KP-304D45 D .625- .875
KP-303E45 KP-304E45 E .875-1.125
KP-303E67 KP-304E67 E 1.125-1.375
E L E C T R I C A L R AT I N G
CIRCUIT RATING (60 HERTZ)
7 Amps 460 V.A.C. 1¼2 H.P.
– OR –
30 Amps 115/230 V.A.C. 1-1¼2 H.P.
7 Amps 460 V.A.C. 1 H.P.
– OR –
30 Amps 115/230 V.A.C. 3 H.P.
HUB CATALOG NUMBER
SIZE AJC JLC JLX
1/2" — KRJC-1303 KRJX-1303
3/4" KRAJC-2303 KRJC-2303 KRJX-2303
1" KRAJC-3303 — —
1/2" — KRJC-1304 KRJX-1304
3/4" KRAJC-2304 KRJC-2304 KRJX-2304
1" KRAJC-3304 — —
1/2" — JLC-1 JLX-1
3/4" AJC-2 JLC-2 JLX-2
1" AJC-3 — —
1Ø
2-Wire
3-Pole
3Ø
3-Wire
4-Pole
Back
Box
Only
K R S R E C E P TA C L E W I T H S W B B O X2
1 Ø
2-Wire
3-Pole
3 Ø
3-Wire
4-Pole
D Type
CIRCUIT
JL Series boxes shown on page F60. Refer to page headings for suitability of specific items.
See page PR18 for available polarization options.
RECEPTACLE
ONLY
AJC JLXJLC
KRS-Series
E Type
KRJ-Series
RECEPTACLE ONLY- CATALOG NUMBER KRJ-303
RECEPTACLE ONLY- CATALOG NUMBER KRJ-304
See page PR18 for available
polarization options.
1Ø, 2-WIRE,3-POLEDEAD END BOX
BOX
ONLY
1Ø, 2-WIRE,3-POLEFEED THRU BOX
BOX
ONLY
KRS-215-1303
KRS-215-2303
KRS-215-3303
SWB-1
SWB-2
SWB-3
SWB-4
SWB-5
SWB-6
KRS-218-1303
KRS-218-2303
KRS-218-3303
3Ø, 3-WIRE,4-POLEDEAD END BOX
BOX
ONLY
3Ø, 3-WIRE,4-POLEFEED THRU BOX
BOX
ONLY
KRS-215-1304
KRS-215-2304
KRS-215-3304
SWB-1
SWB-2
SWB-3
SWB-4
SWB-5
SWB-6
KRS-218-1304
KRS-218-2304
KRS-218-3304
CATALOG NUMBER - SINGLE GANG ONLY
KRS-303 KRS-304
1KRS Series receptacles - Class I, Group D.
2SWB Series mounting splice boxes for receptacles shown above listed on page C19.
Two gang models not available.
See page PR18 for available polarization options.
HUB
SIZE
1/2"
3/4"
1"
PR20PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR22222222222222222222222222222222222222222222222222222222222222222222222222222222222200000000000000000000
KR SERIES • PLUGS AND RECEPTACLES60 AMP/115/230 V.A.C. • 30 AMP/460 V.A.C.
PR21
FEATURES-SPECIFICATIONS
PR
Lis ted F i le No. E23572KRJ Series KRA Series Plug
Class I, Div. 1 & 2, Groups C,DClass l, Zones 1 & 2, llB,llANEMA 7 (C,D)
K R R E C E P TA C L E A S S E M B L I E S
J A L T Y P E M O U N T I N G B O X E S
CATALOG NUMBER
1Ø, 2-WIRE 3Ø, 3-WIRE SPLICE
3-POLE 4-POLE BOX ONLY
KRJX-3603 KRJX-3604 JALX-3
KRJX-4603 KRJX-4604 JALX-4
— — —
KRAJAC-4603 KRAJAC-4604 AJAC-4
KRAJAC-5603 KRAJAC-5604 AJAC-5
KRAJAC-6603 KRAJAC-6604 AJAC-6
KRAJAT-4603 KRAJAT-4604 AJAT-4
KRAJAT-5603 KRAJAT-5604 AJAT-5
KRJ-603 KRJ-604 —
HUB
SIZE
1"
1-1/4"
1-1/4"
1-1/2"
2"
1-1/4"
1-1/2"
HUB
STYLE
“X”-3 Close-up
Plugs Suppl ied
Feed Thru
Top and
Bot tom
T Sides and Top
JAL Ser ies
Boxes
AJA Ser ies
Boxes
KP Type PlugsKRJ-60 Type Receptacles
JAL Type
HUB A B C D E H
1" 2-3/8" 1-5/32" 4-5/8" 5-1/4" 4-1/8" 5/16"
1-1/4" 3-1/8" 1-17/32" 4-5/8" 5-1/4" 4-1/8" 5/16"
Dimensions-Back Boxes
AJAC Types
AJAT Type
K R 6 0 A M P P L U G S
CATALOG NUMBER
1Ø, 2-WIRE, 3Ø, 3-WIRE GROMMET
3-POLE 4-POLE RANGE
KP-603D345 KP-604D345 .500- .875
KP-603E45 KP-604E45 .875-1.125
KP-603E67 KP-604E67 1.125-1.375
— KP-604F34 1.250-1.500
— KP-604F56 1.500-1.750
E L E C T R I C A L R AT I N G
CIRCUIT RATING (60 HERTZ)
30 Amps 460 V.A.C. 3 H.P.
– OR –
60 Amps 115/230 V.A.C. 3 H.P.
30 Amps 460 V.A.C. 5 H.P.
– OR –
60 Amps 115/230 V.A.C. 5 H.P.
1 Ø
2-Wire
3-Pole
3 Ø
3-Wire
4-Pole
RECEPTACLE ONLY
BOX
STYLE
NOTE: For dead end box, use AJAC Series and CUP Series close-up plug.
See page PR18 for available polarization options.
See page PR18 for available polarization
options.
PR21 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222221
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESUGR/UGP INTERCHANGEABLE BLADE STYLE
PR22
FEATURES-SPECIFICATIONS
The ACCEPTOR® UGP/UGR Plug andReceptacle system, with its unique,patented design, is interchangeable1with other NEMA bladed type explo-sion-proof and dust ignition proofdevices. The series has been testedand classified for use with Crouse-Hinds® Ark-Gard®2 and Appleton® U-Line® plugs and receptacles in haz-ardous locations.1 No w available inGFCI version. See page PR26.
How The Acceptor System WorksACCEPTOR receptacles contain anintegral switch which must be closed toenergize the circuit. The design permits only an approved plug to beenergized. To actuate the switch, theplug must be inserted and rotatedclockwise approximately 45o. The plugwill lock into this position preventingaccidental disengagement. To remove,simply push in then turn the plug coun-terclockwise and pull straight out.
Plugs and receptacles may be usedwhere interchangeable bladed devicesare needed in locations made haz-ardous by the presence of flammablegases or vapors, combustible dusts oreasily ignitable fibers and flyings.
Plug can serve to provide power for portable equipment used in bothhazardous and non-hazardous areas.
Applications• Petroleum Refineries
• Chemical Plants
• Wet/Damp Areas
• Corrosive Environments
• Petroleum Plants
• Grain Elevators /Feed Mills
• Flour and Feed Mills
• Indoor or Outdoor Locations
Features• All external hardware is 316 stainless steel
to provide low maintenance and long life
• Factory sealed chamber in UGR recepta-cle contains switch's arcing components
• No additional external seals are required,except in Group B applications
Quick Wiring Plug
• Single piece shell for fewer parts
• Transparent wiring entrance holes for easyconductor insertion
• Screws tighten from side with “full sized”screwdriver
Class I, Div. 1 & 2, Groups B2,C,DClass I, Zones 1 & 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F,GClass IIINEMA 3, 7 (B,C,D), 9 (F,G)
Lis ted F i le No. E91049 and/or E53660
Cer t i f i ed F i le No. LR14667
• Receptacles are U.L. Listed asraintight. Proper sealing againstmoisture is assured
• Spring loaded receptacle cover clos-es when plug is removed to provideprotection when not in use
• Copper-free aluminum (less than4/10 of 1%) alloy resists corrosion
• Electrostatically applied and baked powder epoxy/polyester finish
PLUGACCEPTOR® plugs conform to NEMAconfigurations and can be used withstandard receptacles in non-hazardous areas to maximize equipment utilization.The system's “turn to engage” feature
1.51" 1.69"
2.55"
2Plugs Rated Group B when used with properly rated &
installed receptacles. See next page.
1Exact models classified for interchangeability are
listed in the information sheet provided with the
products. Ark-Gard® is a registered trademark of
Crouse-Hinds®. U-Line® is a registered trademark of Appleton Electric Company®.
UGP-15231 UGP-15231QW
UGP-15232 UGP-15232QW
NEMA
CONFIGURATION
locks in plug and can be used to pre-vent accidental disengagement of criti-cal equipment.
Plugs for use with type S, SO, ST orSTO heavy duty cord.
15 AMP PLUG
W/QUICK WIRING
15 AMP
PLUG
CATALOG NUMBER
20 AMP PLUG
W/QUICK WIRING
20 AMP
PLUG
CATALOG NUMBER
UGP-20231 UGP-20231QW
UGP-20232 UGP-20232QW
NEMA
CONFIGURATIONVOLTAGE
125VAC
250VAC
kbt>QW
Quick Wiring Plug
PR22PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222222
R E C E P TA C L E S A N D A S S E M B L I E S4
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESUGR INTERCHANGEABLE BLADE STYLE
PR23
PR
—
1/2"
3/4"
1"
1/2”
3/4"
1"
—
1/2"
3/4"
1"
1/2”
3/4"
1"
HUB
SIZE
RECEPTACLE ONLY
DEAD END
FEED-THRU
RECEPTACLE ONLY
DEAD END
FEED-THRU
ENCLOSURE
STYLE
NEMA RATING
& CONFIGURATION
1Items in this column are suitable for Class I, Group B in addition to Class I, Groups C, D.
Also suitable for Class I, Zone 1, Groups IIB+H2, IIA.
2Seals must be installed within 6 inches of conduit opening.
3Items in this column may also be used in Class I, Zone 1, Groups IIB, IIA.
Assembly numbers not rated for Group B are shipped as receptacle & back box components.
4Refer to page C19 for additional SWB Series Back Box configurations.
5Canada only configuration
6Canadian Codes now allow “T” combination slots for 15A or 20A plugs. Check breaker and wire feed size for proper application ratings.
NOTE: For replacement receptacle cover and hinge, order KIT-173.
2 POLE
3 WIRE
2 POLE
3 WIRE
—
1/2"
3/4"
1"
1/2”
3/4"
1"
RECEPTACLE ONLY
DEAD END
FEED-THRU
2 POLE
3 WIRE
—
1/2"
3/4"
1"
1/2”
3/4"
1"
RECEPTACLE ONLY
DEAD END
FEED-THRU
2 POLE
3 WIRE
20 Amp
125 Volt
20 Amp
250 Volt
15 Amp
250 Volt
15 Amp
125 Volt
5-20R
5-15R
6-15R
6-20R
UGRO-20231
UGR7-20231
UGR8-20231
UGR9-20231
UGR10-20231
UGR11-20231
UGR12-20231
UGROC-15231
UGR7C-15231
UGR8C-15231
UGR9C-15231
UGR10C-15231
UGR11C-15231
UGR12C-15231
UGRO-20232
UGR7-20232
UGR8-20232
UGR9-20232
UGR10-20232
UGR11-20232
UGR12-20232
UGROC-15232
UGR7C-15232
UGR8C-15232
UGR9C-15232
UGR10C-15232
UGR11C-15232
UGR12C-15232
UGRO-20231
UGR1-20231
UGR2-20231
UGR3-20231
UGR4-20231
UGR5-20231
UGR6-20231
UGROC-15231
UGR1C-15231
UGR2C-15231
UGR3C-15231
UGR4C-15231
UGR5C-15231
UGR6C-15231
UGRO-20232
UGR1-20232
UGR2-20232
UGR3-20232
UGR4-20232
UGR5-20232
UGR6-20232
UGROC-15232
UGR1C-15232
UGR2C-15232
UGR3C-15232
UGR4C-15232
UGR5C-15232
UGR6C-15232
—
UGRB1-20231
UGRB2-20231
UGRB3-20231
UGRB4-20231
UGRB5-20231
UGRB6-20231
—
UGRB1C-15231
UGRB2C-15231
UGRB3C-15231
UGRB4C-15231
UGRB5C-15231
UGRB6C-15231
—
UGRB1-20232
UGRB2-20232
UGRB3-20232
UGRB4-20232
UGRB5-20232
UGRB6-20232
—
UGRB1C-15232
UGRB2C-15232
UGRB3C-15232
UGRB4C-15232
UGRB5C-15232
UGRB6C-15232
SINGLE GANG12GROUPS B, C, D, F & G
SINGLE GANG34GROUPS C, D, F, & G
DOUBLE GANG34GROUPS C D, F, & G
SWB-1, 2, 3 SWB-4, 5, 6 Single Gang Double Gang
5
6
5
6
PR23 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222223
PR24
NEMA CONFIGURATION CATALOG NUMBER WEATHER RATING125V CONNECTOR CAP STYLE
250V CONNECTOR CAP STYLE
20 Amp
125 Volt
2 POLE
3 WIRE
20 Amp
250 Volt
2 POLE
3 WIRE
6-20R with T-slots
Breech-Lock with NotchFlip Type
5-20R with T-slots
Breech-Lock with NotchFlip Type
Killark 250V Plugs20 Amp15 Amp
Killark 125V Plugs
20 Amp15 Amp
UGRC-20231B
UGRC-20231F
3UGP-20231QW
UGP-15231QW
UGRC-20232B
UGRC-20232F
3UGP-20232QW
UGP-15232QW
N4X*N3**
N4X*N3**
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESUGRC CONNECTORS
FEATURES-SPECIFICATIONS
Connector with Breech-Lock Cap “3rd Hand” Plug Operation
Class I, Div. 1 & 2, Groups B,C,D1
Class I, Zones 1 & 2, Groups IIB+H2, IIA1
Class II, Div. 1 & 2, Groups F,G2
Class IIINEMA 3, 4X*
Cer t i f i ed F i le No. LR14667
UGRC Connector
Breech cap model shown, Flip cap model dimensions
are similar
CONNECTORS
The ACCEPTOR® UGRC Connector com-plements UGP/UGR Plugs andReceptacles, as well as Ground FaultProtected UGFI and UGRGF Models.
Used with Acceptor plugs, connectors canextend the reach for hazardous location ratedportable equipment such as hand lamps.Connectors eliminate the need for user cre-ated corded box mounted receptacles.
UGRC Connectors are interchangeableand classified for use with other NEMAbladed type explosion-proof and dustignition proof plugs, including Crouse-Hinds® Ark-Gard®2 and Appleton®ULine®.
Features• Available with the exclusive Breech-Lock
Cap (see PR3 for more info) - patentednotch provides “3rd hand” plug operation(holds lid open while one hand operatesplug, and other holds connector).
• Factory Sealed Construction
• Suitable for 14 or 12 gauge SOOW orsimilar cable
• Copper-free aluminum (less than 4/10 of1%) alloy resists corrosion
• Electrostatically applied and baked pow-der epoxy/polyester finish
• Dead Front Construction with integralswitch - requires Hazardous Rated NEMABladed plug for operation
Ark-Gard® is a registered trademark of Crouse-Hinds®U-Line® is a registered trademark of AppletonElectric Company®
Industrial Applications• Petroleum Refineries• Chemical/Petrochemical Plants• Oil Rigs & Platforms• Wet/Corrosive Environments• Grain Elevators
Dimensions
1
2
Connector shown with Acceptor UGRP receptacle mounted
in explosion proof Quantum® enclosure
8.25
2.883.69
*Breech cap models N4X with lid closed and turned, N3 When Plug inserted Hinge Up
**Flip Lid models N3 with hinge in UP position with or without plug
Replacement Cap and Hinge Kits: Breech KIT-173B, Flip KIT-173
1CSA certified Class I Div.I for Canada and/or other jurisditions accepting CSA.
2CCSAUS Class II, Groups F & G for US and Canada.
3Remove QW in catalog number for Standard Wiring type plug.
Flip Cap
Cer t i f i ed F i le No. LR14667C US
UGP Plug
PR24PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222222222222222222222222222222444444444444444444444
PR25
PR
FEATURES-SPECIFICATIONS
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESUGRP PANEL MOUNT RECEPTACLES
* UGRP Receptacles are available “Factory Installed” in the following series:Enclosures - Series EXB, B7E Distribution Equipment-Series D2L, B7L Lighting Panelboards* Contact factory for ordering information
Class I, Div. 1 & 2, Groups B,C,D1
Class I, Zones 1 & 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F,GClass IIINEMA 3, 4X*
Cer t i f i ed F i le No. LR146672C USTypical InstallationBreech Cap Model
Typical CLI Div. Iapplication
Typical CLI Div. 2application2-3/8” K.O.
Breech Caps
Flip Lids
NEMA CONFIGURATION CATALOG NUMBER WEATHER RATING125V PANEL RECEPTACLE CAP STYLE
250V PANEL RECEPTACLE CAP STYLE
20 Amp
125 Volt
2 POLE
3 WIRE
6-20R with T-slots
Breech-Lock with NotchFlip Type
5-20R with T-slots
Breech-Lock with NotchFlip Type
Killark 250V Plugs***20 Amp15 Amp
Killark 125V Plugs***
20 Amp15 Amp
UGRP-20231B
UGRP-20231F
3UGP-20231QW
UGP-15231QW
UGRP-20232B
UGRP-20232F
3UGP-20232QWUGP-15232QW
N4X*N3**
N4X*N3**
*Breech cap models N4X with lid closed and turned, N3 When Plug inserted Hinge Up
**Flip Lid models N3 with hinge in UP position with or without plug
***See PR24 for Plug NEMA Diagram and Dimensions
Replacement Cap and Hinge Kits: Breech KIT-173B, Flip KIT-173
1Class I Div.1 B,C,D in enclosures certified to 325 explosive PSI (2”-11½ NPSM threads).
Class I Div. 2 in standard location enclosures using only non-arcing components.
2cCSAus Certified for United States, Canada, and other jurisdictions accepting the mark.
3Remove QW in catalog number for Standard Wiring type plug.
20 Amp
250 Volt
2 POLE
3 WIRE
Flip Cap
Breech Cap model shown.
Flip Cap model dimensions are similar
PANEL RECEPTACLES
The ACCEPTOR® UGRP PanelReceptacle complements UGP/UGR Plugsand Receptacles, as well as Ground FaultProtected UGFI and UGRGF Models.
Used with Acceptor plugs, panel recepta-cles provide local power for hazardous loca-tion rated portable equipment such as handlamps. Units are suitable for Class I Div. 1or Class I Div.2 depending on the enclo-sure type used1.
UGRP Panel Receptacles are inter-changeable and classified for use withother NEMA bladed type explosion-proofand dust ignition proof plugs, includingCrouse-Hinds® Ark-Gard®2 andAppleton® ULine®.
Features• Available with the exclusive Breech-Lock
Cap (see PR3 for more info) - patentednotch provides “3rd hand” plug opera-tion (holds lid open while one handoperates plug, and other holds connector).
• Factory Sealed Construction
• Copper-free aluminum (less than 4/10 of1%) alloy resists corrosion
• Electrostatically applied and bakedpowder epoxy/polyester finish
• Dead Front Construction with integralswitch - requires Hazardous RatedNEMA Bladed plug for operation
Ark-Gard® is a registered trademark of Crouse-Hinds®U-Line® is a registered trademark of AppletonElectric Company®
Industrial Applications• Petroleum Refineries• Chemical/Petrochemical Plants• Oil Rigs & Platforms• Wet/Corrosive Environments• Grain Elevators
Dimensions
3.69
4.50
2.94
Breech Lid
PR25 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222225
X H L I N C A N D E S C E N T
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESADAPTER AND ACCESSORIES
PR26
FEATURES-SPECIFICATIONS
U G R A A D A P T E R K I T
XHL SERIES HAND LAMPSUNIVERSAL ADAPTER KITACCEPTOR® receptacles are availablewith an adapter kit for mounting toCrouse-Hinds® EDS Series or Appleton®
EFD Series back boxes.
ACCEPTOR receptacles properlyinstalled with these adapter kits areU.L. Listed for use in Class I, Div. 2,Groups B,C,D hazardous locations andZone II, Groups IIB + H2, IIA.
Kit contains one ACCEPTOR® recepta-cle plus adapter plate and mountingbolts.
UGRA-20231
UGRA-20232
ADAPTER KIT
CATALOG NUMBER
NEMA RATING
& CONFIGURATION
2 POLE
3 WIRE
2 POLE
3 WIRE
Features
• Factory Sealed
• Test and Reset push buttons are provided on cover assembly, with optional pilot light available1Unit should be tested monthly
• Includes new GFCI to meet latestUL943 GFCI standards revisions
• Exterior gasket provides NEMA 3weatherproof protection
• Ground boss for grounding in thesplice box
• Color coded wiring and stainless steel-cover bolts
• Receptacle used is UGRO-20231.See page PR23
Lis ted F i le No. E97760
XHLF FluorescentClass I, Div. 1 & 2, Groups C,DClass l, Zones 1 & 2, Groups llB,llAClass lI, Div. 1 & 2, Groups E,F,G
XHLF26 Fluorescent hand lamp
XHLF26-50KP
Fluorescent hand lamp wi th
- 50 ' o f 16/3 SOW cord and
15A Acceptor p lug
5-20R
20 Amp 125 Volt
6-20R
20 Amp 250 Volt
XHL-100
XHL-GL
XHLG
XHLS
Handlamp
Replacement g lobe
Replacement guard
Replacement socke t
CATALOG NUMBER DESCRIPTION
Lis ted F i le No. E91049
XHL IncandescentClass I, Div. 1 & 2, Groups C,DClass l, Zones 1 & 2, Groups llB,llA
Class I, Div. 1 & 2, Groups C,DClass l, Zones 1 & 2, Groups llB,llAClass lI, Div. 1 & 2, Groups F,GClass IIINEMA 3, 7(C,D) 9(F,G)
Lis ted F i le No. E97760
Cer t i f i ed F i le No. LR10019
CATALOG NUMBER DESCRIPTION
NEMA RATING &
CONFIGURATION
20A, 125V, 2P, 3W
ENCLOSURE
STYLE
Dead End
Dead End
Dead End
Feed Thru
Feed Thru
Feed Thru
A handy accessory to the ACCEPTOR®
Series, these hand lamps can be usedas an illumination source where flam-mable materials are present, such asprocessed finish goods, storage vats,or handling areas.
See page L14 for detailedinformation and features.
UGRA
Cer t i f i ed LR14667
Cer t i f ied LR11714
See f i les for deta i ls or ca l l Ki l lark .
1 For Red LED pi lot l ight ind icator of l ive
c i rcu i t , add “-PL” to cata log number.
Example - UGRGF107-PL.
XHL XHLF UGRGF
XHLF FLUORESCENT (120VAC)
GFI PROTECTED RECEPTACLEUtilizes FXS GFI and ACCEPTOR®
receptacle to interrupt a circuit, when aground fault is detected on equipmentwhich may be handled by personnel inhazardous locations.
Electrical Rating
GFI units are rated at 20A, 120 VAC,
60Hz. Class A.
4-6 miliamp trip setting
Trip Time-UL Curve
HUB
SIZE
1/2”
3/4”
1”
1/2”
3/4”
1”
CATALOG1NUMBER
UGRGF107
UGRGF108
UGRGF109
UGRGF110
UGRGF111
UGRGF112
PR26PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222222222222222222222222222222666666666666666666666
1/2” HUB UGFI202C3
3/4” HUB UGFI202C3
1” HUB UGFI202C3
1/2” HUB UGFI152C3
3/4” HUB UGFI152C3
1” HUB UGFI152C3
ACCEPTOR® SERIES • PLUGS AND RECEPTACLESADAPTER AND ACCESSORIES
PR27
FEATURES-SPECIFICATIONS
PRThe GFCI protected ACCEPTOR® is the
solution to OSHA's requirements for
GFCI protection when using portable
equipment in hazardous and wet loca-
tions. For use with 125V, or125/250V315 or 20 amp receptacles without GFCI
protection, the Adapter Unit provides
GFCI and circuit protection to connect-
ed apparatus by simply being plugged
into an existing receptacle.
The Hard-Wired Unit provides the
same protection and is used directly
as a GFCI protected device. Units are
feed-through with one close-up plug.
Lis ted F i le No. E91049
Cer t i f i ed F i le No. LR14667
PUSH TOTEST
OF
FON
RESET
Typical Application with
XHL Series Hand Lamp
PUSH TOTEST
OF
FON
RESET
7 3/86
6 1/8
7 7/8
Hard-Wired Unit
• Adapter UnitClass I, Div. 2, Groups B,C,DClass I, Zone 2, Groups IIB+H2, IIAClass II, Div. 1 & 2, Groups F,GClass III, Div. 1 & 2
• Hard-Wired UnitClass I, Div. 1 & 2, Groups B,C,DClass I, Zones 1 & 2, Groups IIB+ H2, IIAClass II, Div. 1 & 2, Groups F,GClass III, Div. 1 & 2
NEMA 3 ENCLOSURE TYPE(Adapter or Hard-Wired units)
Adapter Unit• No need to permanently alter existing
installations; Portable Unit can betemporarily hung using included strapnear an existing receptacle whereverprotection is required
• Factory Sealed Unit
• Acceptor® plug and cord set includedwith Adapter Unit. Cord is 36"
Hard-Wired Unit• provides GFCI and circuit protection in
new installations, or as an upgrade orreplacement for non-GFCI receptacles
• Factory Sealed, except Group B
Adapter and Hard-Wired Unit• GFCI device also provides circuit
protection, for connected apparatus,against current overload and shortcircuits
• Acceptor® receptacles and plugs are intermateable with bothCrouse-Hinds® Ark-Gard®2 andAppleton® U-Line® products
• Amber pilot light provides indicationthat the receptacle is energized.
• Units can be Padlocked OFF for main-tained safety
• Fully gasketed GFCI compartmentprevents moisture from damagingelectronic components
• Same high quality materials as the standard ACCEPTOR
®
1Hard-Wired assemblies in Group B areas require
sealing within 6" of enclosure.
2125VAC & 250 VAC devices are C CSA US
certified;125VAC devices are also UL Listed.
32P 250V units are for 2 “hot line” applications
and include 2P 5mA GFI breakers. 2P Units are
for 20/240V or 120/208Y Grounded Power Supply
Systems ONLY. Do NOT use with Delta supply
systems.
Ark-Gard® is a registered trademark of Crouse-Hinds®
U-Line® is a registered trademark of Appleton Electric
Company®.
Adapter Unit
UGFIGROUND FAULTPROTECTOR
5-20R
5-15R
6-20R
6-15R
20A
125V
2
15A
125V
2
1/2” HUB UGFI20C1
3/4” HUB UGFI20C2
1” HUB UGFI20C3
1/2” HUB UGFI15C1
3/4” HUB UGFI15C2
1” HUB UGFI15C3
5-20R
5-15R
6-20R
6-15R
20A
250V
23
15A
250V
23
HARD WIRED (PERMANENTLY MOUNTED)
GFCI RECEPTACLE
kbt>2P 250V GFI
G F C I R E C E P TA C L E A D A P T E R ( W / C O R D S E T )
20A
125V
2
15A
125V
2
20A
250V
23
15A
250V
23
UGFI20AD
UGFI15AD
UGFI202AD
UGFI152AD
C US
PR27 PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR222222222222222222222222222222222222222222222222222222222227