Ser ies 613

MAGNUM™ Double Hung Window

DATE: NOVEMBER 2009 | REPLACES: AUGUST 2003

Photo courtesy of MidCity Windows

DE

SIG

NE

R S

ER

IES

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung WindowDATE: NOV 09REPLACES: AUG 03SCALE: NOT TO SCALE

TYPICAL CONFIGURATIONS

KEY FEATURES / PERFORMANCE CHARACTERISTICS

Series 613 Double-hung window internal view

Maximum Panel Height* 1050mm

Maximum Panel Width* 1155mm

Maximum Glass Thickness ≤ 20mm

• Tested for compliance with the relevant Australian Standards.

• Achieves a high water resistance of 300Pa.

• 102mm Frame, mullion and transom have a soft 2mm internal radius.

• Both sashes can be hinged back into the room to allow cleaning of both sides of the glass from inside, without having to remove the flyscreen, ideal in elevated applications and where privacy screens are used.

• Sashes secured with the Vantage custom key or non-key locking cam handle.

• When windows are a powder coated finish the lower corners on the top sash are fitted with die cast horns as standard. Horns are not available in anodised finishes. Windows can be ordered with or without sash horns, clearly nominate when ordering.

• Powder coat finished windows can also be ordered without federation sash horns.

• MAGNUM™ double-hung windows can be fitted with external flyscreens within the frame line, no turn buckles required.

* Subject to individual site conditions and wind loads. Contact AWS Technical Support for more information, e-mail techsupport@awsaustralia.com.au

IMPORTANT NOTESash height to Width RatioThe maximum width of the double-hung sash is limited to 110% of the sash height

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

PAGE | 201

MORE INFORMATION For the latest updates regarding this product visit our website www.vantagealuminium.com.au

SOUNd REdUCTION

We have tested the MAGNUM™ double-hung with 6.38mm laminated glass. Window was fitted with weatherpile seals externally and ‘Aquamac’ internally and at meeting rails.

Glass description

6.38mm Laminated glass 30dB(A) RW30

Secondary glazed sliding window will give significantly higher numbers

DATE: NOV 09REPLACES: AUG 03SCALE: NOT TOS CALE

WERS RATINGS

Single Glazed Glass description COOLING HEATING Uw SHGCw Tvw Inf

5mm Clear 27% 6% 6.4 0.57 0.59 4.75

5mm Grey 38% -2% 6.4 0.42 0.33 4.75

5mm EverGreen 40% -3% 6.4 0.40 0.48 4.75

6.38mm Solect 42% 20% 4.9 0.47 0.54 4.75

6.38mm Comfort Plus 48% 21% 4.9 0.39 0.43 4.75

double Glazed Glass description COOLING HEATING Uw SHGCw Tvw Inf

4Clr/10Gap/4Clr 41% 28% 4.5 0.51 0.53 4.75

5Clr/8Gap/5Clr 41% 27% 4.6 0.50 0.53 4.75

4Clr/10Gap/4EA 46% 32% 4.0 0.48 0.49 4.75

4Az/10Gap/4EA 59% 21% 4.0 0.28 0.41 4.75

5EG/8Ar/5EA 59% 22% 3.9 0.29 0.40 4.75

2d & 3d CAd FILES AvAILAbLEGO TO: www.vantagealuminium.com.au > CAD & Revit 3D Files CAD file: DWG or DXF VAN_613

HOW TO SPECIFY

SYSTEM NAME

Vantage Series 613 MAGNUM™

Double Hung Window

FINISH

Powder Coat

Anodised

COLOUR

Select from the Vantage range of

approved powder coat or anodising

colours

GLASS

Specify thickness ≤ 20mm

Specify thermal performance where

applicable (Uv & SHGC)

Specify acoustic performance where

applicable (RW)

HARdWARE

Refer to hardware selection guide for

compatible options

Specification Assistance

Need help specifying this product? call 1300 123 000 and our qualified technical advisors will assist you with product selection and specification for your project

Specification Assistance

Need help specifying this product? email techsupport@awsaustralia.com.au and our qualified technical advisors will assist you with product selection and specification for your project.

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

SPECIFIERS CHECKLIST

Not all double-hung windows are the same. Most have sashes that go up and down - but if you want your windows to perform and match the architectural appearance you are looking for there are some things you should check/compare when choosing your supplier.

FEATURE Series 613 Opposition

does the window comply with the relevant Australian Standards. All windows should comply but it pays to ask for written proof.

designed for exposed locations. Series 613 has a 300Pa water resistance as standard. This makes the product suitable for exposed locations.

Can I make large windows and still comply. We can make this double-hung up to 2100mm x 1510mm wide and still comply.Our sashes and matching fixed sidelight will accept glass from 4mm to 8.38mm single glaze or 20mm insulating glass units using custom stiles and rails to accept this thicker glass panel

Wide frame with bold sashes. 102mm wide perimeter frame.30mm thick sashes.

Tilt sash standard. MAGNUM™ sashes can be tilted back into the room to allow cleaning of the external face ofthe glass from inside the building. This will be a major advantage in elevated situations where external access may be difficult to impossible.

Custom locking options. We have designed a locking cam for this window that won’t catch the curtains or blinds.Locks can be colour matched to the sash finish.

Clean flyscreen installation. Flyscreens nest into the perimeter frame and are secured with custom concealed nylonspring clips that reduce the chance of screens rattling or falling out.

Window can be coupled to sliding doors or other windows without visible rivets.

Rounded internal frame corners where ever possible. The main perimeter frame has 2mm soft internal corner radius.Lowlight mullions also have the same soft internal radius plus they are setback 2mm from the edge like timber windows to give a clean finish.Modern paint finishes don’t like sharp corners.

Paddington federation trim option available. We can clip Paddington federation trims straight to the main frame.These trims can be colour matched or coloured to contrast with the main frame.

Compatible products. MAGNUM™ 613 double-hung window has been designed to match and couple with a large range of other MAGNUM™ products. Refer installation section for more information.

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

DATE: NOV 09REPLACES: AUG 03SCALE: NOT TO SCALE

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

PAGE | 203

DATE: NOV 09REPLACES: AUG 03SCALE: NOT TO SCALE

dESIGN FEATURES

Get the solid appearance of timber with the benefits of aluminium:• Strength.• Weather performance.• Sound reduction.• High performance powder coat and anodised finishes.• Security.• Flyscreening.

The window has been tested for compliance with the relevant Australian Standards achieving a high water resistance of 300Pa.

102mm Frame, mullion and transom have a soft 2mm internal radius.

Both sashes can be hinged back into the room to allow cleaning of both sides of the glass from inside, without having to remove the flyscreen.

Sashes can be secured with the Vantage custom key or non-key locking cam handle.

When windows are a powder coated finish the lower corners on the top sash are fitted with die cast horns as standard. Horns are not available in anodised finishes. Windows can be ordered with or without sash horns, clearly nominate when ordering.

MAGNUM™ double-hung windows can be fitted with external flyscreens within the frame line, no turn buckles required.

The window is compatible (appearance) with the high performance MAGNUM™ horizontal sliding, awning and casement windows. A large range of snap couplers allow these windows to be joined at 90°, 135° and 180° without unsightly rivets or screws. Refer installation section for more information.

These couplers would also allow this window to couple to Bi-fold windows, Bi-fold doors, French doors and Sliding doors.

Matching fixed sidelights / highlights and lowlights.

Sashes and sidelight will accept glass from 4mm to 8.38mm single glaze or 20mm insulating glass units.

The perimeter frame will accept the optional 'Paddington' federation trims, as illustrated in these notes

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung WindowDATE: NOV 09REPLACES: AUG 03SCALE: NOT TO SCALE

WINdOW OPTIONS

F FF

F

F

FF

The double-hung system is inlaid into dedicated perimeter frame and mullions, refer cross sectional details.

Combination windows with transom are fabricated as separate units then joined with 'I' coupler 42030.

Important Note:In elevated situations (above ground level) the position of the transom should be considered with safety in mind. In some areas there may be regulations covering the height of the transom above floor level.

refer AS1288 for lowlight glass minimum requirements.

type 'F'type 'FF'typical multiple fixed window illustrated.

Pure fixed windows can be fabricated out of the double-hung frame as a single or multiple units. We can also fabricate similar fixed windows from the awning frame, refer Series 616.

Full height fixed lights (without transoms) that can be mistaken for door openings are to be glazed with safety glass, refer AS1288. If in doubt as to whether a window requires safety glass always err on the side of safety.

type 'dd'

type 'dFd'

type 'd'Max. height = 2100Max. width = 1210

type 'dF'Max. width = 3010

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

PAGE | 205

WINdOW COUPLING OPTIONS

DATE: NOV 09REPLACES: AUG 03SCALE: NOT TO SCALE

FF

F

F F

Series 613 windows can be clipped to Series 541, 542 or 618 sliding doors using the box coupler 42027 or 'I' coupler 42030*. Likewise 90° corners using 42022 coupler and 135° bay corners with 42026. Refer installation section for more information.

* Note:As the double-hung transom window (illustrated left) has been fabricated from two separate windows with 42030 'I' coupler at the transom joint. This window requires the heavier box coupler (42027) vertically when clipped to the door.

Series 613 windows will also clip to Series 548 French doors using the box coupler 42027 or 'I' coupler 42030.

Likewise 90° corners using 42022 coupler and 135° bay corners with 42026.

The 'I' coupler 42030 can only be used vertically if the double-hung windows have no transoms as shown left.

The 'I' coupler 42030 can also be used to create a significantly stronger mullion by coupling two windows together as shown left.

Note: This assembly can't have horizontal breaks in the windows (transoms) as this would result in broken mullion members

Typical strength examples on type 'DF' as shown and type 'DD':2100 x 2410 = 2200Pa *2100 x 2710 = 2200Pa *2100 x 3010 = 1550Pa * Limited by water rating. Limited by meeting stile strength on the double-hung window.

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

vERTICAL CROSS SECTION - THROUGH OPENING SASH

Vantage custom cam handle.

'Aquamac' seal.

Interlocked meeting stiles.

Single glazed sashes shown left will accept glass up to 8.38mm thick.Dedicated double glazed sashes shown above right, will accept 20mm thick Insulating Glass Units.

Sash lifts.

Bottom rail double sealed with 'Aquamac'.

Stainless steel assembly screws.

101.60

Meeting Rail StrengthThis table is a guide to the serviceability strength (1/150) of the meeting rails on Series 613 double-hung windows.

Series 613 sliding windows will resist 300Pa water which makes them suitable for the most exposed residential locations in Australia.

Head

Meeting rails

Sill

Window Meeting

Height Width Rails

Type mm mm Pa

D 2100 910 2200

D 2100 1210 2200

CAD file: DWG or DXF vAN_613

DATE: NOV 09REPLACES: AUG 03SCALE: HALF FULL SIzE

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

PAGE | 207

DATE: NOV 09REPLACES: AUG O3SCALE: HALF FULL SIzE

External frame recess will accept Vantage extruded flyscreen - when required.

Side rails sealed with 'Aquamac' on the inside and weatherpile on the outside.

Nylon sash latches can be disengaged to allow sashes to be tilted back into the room.This allows both sides of the glass to be cleaned from inside.

Top sash fitted with die cast horns as illustrated below (not available on anodised finishes).

Heavy duty spring balances allow us to fit thick/heavy glass including double glazed units.

Double glazed windows have dedicated sashes that will accept 20mm thick Insulating Glass Units

Both top and bottom sashes fold in for easy cleaning

When the sashes tilt back into the room the support shoes lock into the jamb guides.

Jamb

HORIZONTAL CROSS SECTION - THROUGH OPENING SASH

MORE INFORMATION See the sashes open, close and tilt on our web site www.vantagealuminium.com.au

Sash Horn

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

OPTIONAL FLYSCREEN

4630

Flys

cree

n he

ight

= D

- 7

6

Fit nylon canoe clip to the underside of flyscreen to create a small gap, to allow water escape.

72814 (full size)

Vantage extruded flyscreen frame with clean flat lines and radius corners to match window frame.

72815 (full size)

Vantage extruded barrier flyscreen frame.

Cross brace fitted when flyscreen height exceeds 1600mm.

See how easy it is to fit screens to MAGNUM™ double-hung at: www.vantagealuminium.com.au

Custom nylon flyscreen clip fitted into jambs, keeps the screen on centre.

DATE: NOV 09REPLACES: AUG 03SCALE: HALF FULL SIzE

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

PAGE | 209

DATE: NOV 09REPLACES: AUG O3SCALE: NOT TO SCALE

Series 613 MAGNUM™ perimeter frame will accept 'Paddington' trims as shown on this page.Have also included the optional 28 x 10mm raisedcolonial bars on this detail.Refer the web site for coloured details.and cad drawings (DXF or DWG)

'Paddington' trims can be seen on our web site at: www.vantagealuminium.com.au

CAD file: DWG or DXF vAN_613

OPTIONAL ‘PAddINGTON’ FEdERATION TRIMS & bOLd APPLIEd COLONIAL bARS

DE

SIG

NE

R S

ER

IES

© A

rchi

tect

ural

Win

dow

Sys

tem

s Pt

y Lt

d 2

002-

2009

Ser ies 613

MAGNUM™ Double Hung Window

ALTERNATIvE COMMERCIAL dOUbLE HUNG

Scale: Not to scale

Alternative Commercial double-hung WindowIf you are looking for a bolder frame consider the AWS Commercial double-hung window Series 463.

Features overview:• Bold square commercial frame with built-in nailing fin.• Nailing fin sub-sill is standard.• Compatible with conventional CentreGLAZE™ shopfront framing.

Refer AWS Commercial Specifier Manual for more details.Coloured animated images can be seen on AWS web site:www.awscommercial.com.au

Head

Sill

Meeting rails

DATE: NOV 09REPLACES: AUG 03SCALE: HALF FULL SIzE