PLASMA TVSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : MF-056A
MODEL : 42PX3RVC/RV42PX3RVC/RV-TA
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
PRVOLMENUTV/AV OK
- 2 -
CONTENTS
SAFETY PRECAUTIONS ....................................................................................3
DESCRIPTION OF CONTROLS ..........................................................................4
SPECIFICATIONS................................................................................................8
ADJUSTMENT INSTRUCTIONS .......................................................................11
TROUBLE SHOOTING GUIDE..........................................................................15
BLOCK DIAGRAM.............................................................................................24
EXPLODED VIEW..............................................................................................26
EXPLODED VIEW PARTS LIST ........................................................................27
REPLACEMENT PARTS LIST...........................................................................28
SCHEMATIC DIAGRAM.........................................................................................
PRINTED CIRCUIT BOARD ..................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
MULTIMEDIASelects the Component, RGB or DVI
modes.switches the set on from standby.
PIP/DWSwitches the sub picture on or off.
Selects PIP or DW modes.PIP PR + /-
Selects a programme for the sub picture.SWAP
Alternates between main and sub pic-ture.
PIP INPUTSelects the input mode for the sub pic-
ture.WIN.SIZE
Adjusts the sub picture size.POSITION
Moves the sub picture to DD / EE or FF / GGdirection.
POWERswitches the set on from standby oroff to standby.
ARC Changes the picture format.
MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.
SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favourite programme is set toOff. Otherwise each press of thisbutton will select a stored favoriteprogramme.
SSMTo select the sound appropriate toyour viewing programme character.
NUMBER buttons
SLEEPSets the sleep timer.
I/IISelects the language during dual lan-guage broadcast.Selects the sound output.
TEXT/*These buttons are used for teletext.For further details, see the ‘Teletext’section.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.
LISTDisplays the programme table.
TV/AVSelects the TV, AV, Component, RGB
or DVI modes.switches the set on from standby.
MUTESwitches the sound on or off.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
OKaccepts your selection or displays the
current mode.
PSMAdjusts the factory preset picture
according to the room.
SPLIT ZOOMEnlarge the screen with regular
ration.
- 4 -
DESCRIPTION OF CONTROLS
- 5 -
<Front Panel Controls>
PRVOLMENUTV/AV OK
PRVOLMENUTV/AV OK
1 32 4 5 6 7
1. Remote Control Sensor
2. Power IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on.
3. Power ButtonSwitches the set on from standby or off to standby.
4. TV/AV ButtonSelects the TV, AV, Component, RGB or HDMI modes. Switches the set on from standby.
5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
6. OKAccepts your selection or displays the current mode.
7. DD / EE (Programme Up/Down)Selects a programme or a menu item.Switches the set on from standby.FF / GG (Volume Up/Down)Adjusts the volume.Adjusts menu settings.
- 6 -
<Back Panel>
S-VIDEO
VID
EO
AU
DIO
RL/
MO
NO
A/V INPUT2A/V INPUT2
AC INPUT
RS-232C INPUT(CONTROL/SERVICE)
S-VIDEOS-VIDEO
(MONO)
AUDIO AUDIO
L R
AUDIO AUDIO
L R
AUDIO AUDIO
L R
Antenna
VIDEO VIDEO
REMOTECONTROL
HDMI/DVI(VIDEO) AUDIO INPUT RGB INPUT
VIDEOVIDEO
COMPONENTCOMPONENT INPUT INPUT 2 2
COMPONENTCOMPONENT INPUT INPUT 1 1
MONITMONITOR OUTPUTOR OUTPUT
A/V INPUTA/V INPUT 1 1
VVARIABLE ARIABLE AUDIO OUTAUDIO OUT
1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER, DVD or STB to this socket.Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or theEMI Filter core along with separate cable.
2. CONTROL LOCK / REMOTE CONTROL
3. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.
5. VIDEO/AUDIO IN/OUT SOCKETS (A/V INPUT 1)Connect the video/audio out sockets of external equipmentto these sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in A/V INPUT 1.
6. VARIABLE AUDIO OUTPUT
7. ANTENNA INPUT
8. POWER CORD SOCKETThis the set operates on an AC power. The voltage is indicat-ed on the Specifications page. Never attempt to operate theset on DC power.
9. AUDIO/VIDEO INPUT (A/V INPUT 2)S-VIDEO/AUDIO IN SOCKETS
1 42 3 5 7 86
9
- 7 -
AS mark
LG TV
Owner’s Manual
1.5V1.5V
Alkaline batteries Power Cord
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
Remote Control handset
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
AccessoriesAccessories
Tilt wall mounting bracket Video cables Audio cablesCeiling mounting bracket
40
4250
42
40
- Secure the TV assembly by joinning it to a wall by using the Eye Bolts/Wall brackets.
Joinning the TV assembly to the wall to protect the set tumbling
• After the set must be mounted on a desktop, install the Eye Bolts on the set asshown.Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product),as shown.Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.
• Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.
2-Wall brackets
2-Eye Bolts
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
- 8 -
V Application RangeThis spec is applied to the 42”PDP TV used MF-056A Chassis.
V Specification
Each part is tested as below without special appointment.1) Temperature : 25±5°C (77±9°F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: CE, IEC specificationEMC : CE, IEC
V General Specification
1. Module Specification
Remark
Safety : IEC60065, EMI : CISPR13
Model Name
42PX3RVC-TA
Market
Non-EU
Remark
PDP
LGE SPEC
Maker : SONY/ Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V7xxxx
RGB Closed Type, Film Filter
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
100-240V~, 50/60Hz
No
1
2
3
4
5
6
Item
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
2. Model Specification
- 9 -
Item
Market
Broadcasting system
Available Channel
Receiving system
Video Input (2EA)
Video Output (1EA)
S-Video Input (2EA)
Component Input(2EA)
RGB Input(1EA)
HDMI Input(1EA)
Audio Input(5EA)
Wired Control
Audio variable out
No
1
2
3
4
5
6
7
8
9
10
11
12
13
Specification
Non-EU
PAL B/G/I/D/K, NTSC
BAND PAL NTSC
VHF/UHF C1~C69 2~83
CATV S1~S47 1~71
Upper Heterodyne
PAL, SECAM, NTSC
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
RGB-DTV
HDMI-PC
HDMI-DTV
PC Audio, Component(2EA), AV(2EA)
Remark
4 System : PAL, SECAM, NTSC,PAL60
4 System : PAL, SECAM, NTSC,PAL60
4 System : PAL, SECAM, NTSC,PAL60
L/R Input
- 10 -
RGB / HDMI mode
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.05
70.01
75.00
75.06
60.02
60.02
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
54.348
63.995
67.500
68.681
60.023
63.981
RGB / HDMI mode
50PX3RV series
42PX3RV series
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1360x768
1366x768
1152x864
1152x870
1280x960
1280x768
1280x1024
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25 (RGB)
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.00
75.02
85.00
60.00
75.02
85.00
60.05
70.01
75.00
85.00
75.06
60.00
75.00
85.00
60.02
60.02
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
47.700
59.625
68.500
47.700
59.625
69.500
54.348
63.995
67.500
77.487
68.681
47.693
60.091
68.504
60.023
63.981
- 11 -
ADJUSTMENT INSTRUCTIONS
1. Application ObjectThese instructions apply to the MF-056A Chassis.
2. Specification(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100-220V,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE
PATTERN.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.
Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), afterimage may be occur in the black level part of thescreen.
3. Channel memory
3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.
3-2. Channel memory Method 1) Select “PDP” and “Hurricane” on Model dialog. And check
your connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)
2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see “Ready”.)
[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.
3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].
4) Click the [Download] button.It means the completion of the CH memory download if allitems show ‘OK’ and Status is changed by ‘PASS’ at thelower right corner of the window.
5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.
3-3 Sub program download
1) Select “PDP” and “Hurricane” on Model dialog. And checkyour connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)(Fig. 1)
(Fig. 3)
(Fig. 3-1)
- 12 -
2) Connect RS-232C cable and turn on the power. (Use thespecial Cable For Sub-program) (If your connection hascompleted, you can see “Ready”)
4. POWER PCB Assy V oltage Adjustments (Va, Vs Voltage Adjustments)
4-1. Test Equipment : D.M.M. 1EA
4-2. Adjustment Method
(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P807, connect
- terminal to GND pin of P807.3) After turning RV501, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)
(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P807, connect
– terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)
5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download
5-1. Required T est Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID
TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub
15Pin cable, DVI to HDMI cable
5-2. Setting of device
5.3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC
& Cable.2) Turn on the PC & EDID Download Jig. And Execute the
S/W : EDID TESTER Ver,2.53) Set up S/W option
Repeat Number : 5Device Address : A0PageByte : 8
4) Power on the Set
5.4. Sequence of Adjustment
(1) DDC data of Analog-RGB1) Init the data
2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]
3) Set the S/W as below.4) Push the “Write Data & Verify”button. And confirm “Yes”.5) If the writing is finished, you will see the “OK” message.
Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)
(Fig. 4) Connection diagram of power adjustment for measuring
(Fig. 5) Connection Diagram of DDC download
- 13 -
6. Auto A V(CVBS) Color Balance
6-1. Required- This AV color balance adjustment should be performed beforwhite Balance Adjustment
6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator
: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)
6-3. Method of Auto Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar
Pattern) into video input.(42PX4RV-TA : AV1/AV2 Input 50Hz,42PX4RV-ZA : AV4/AV5 Input)
2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
7. Adjustment of White Balance
7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for auto adjustment)4) AV Pattern Generator
7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)
W Auto adjustment Map(RS-232C)
7-3. Adjustment of White Balance
O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.
O For manual adjustment, it is also possible by the followingsequence.
1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.
2) As below Fig.7-1, Supply 216Level (85 IRE) full screenpattern to Video input.(42PX4RV-TA : AV1/AV2 INPUT 50Hz,42PX4RV-ZA : AV4/AV5 INPUT)
3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.6) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.
7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.
8) Adjust it until color coordination becomes as below.(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)[MF-056A : 42PX4RV-TA/ZA] - VGA 42”Bright : High Light : 80 ± 20cdColor-Coordinate : High Light : X : 0.285 ± 0.003
Y : 0.295 ± 0.003Color Temperature : 9,300°K ± 500°K
9) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C
(Fig. 7-1) Pattern for Adjustment of White Balance
216 Level (85 IRE)
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
MF-056A : RT-42PX40/ RZ-42PX40
ProtocolSetting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern
(Fig. 7) Connection Diagram of Auto W/B adjustment
MSPG-2100 /MSTG- 5200
216 Level (85 IRE)
COLORANALYZERTYPE ; CA-100
CVBSsignalinput
RS-232C Serial Communication
- 14 -
8. Auto Component Color Balance
8-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator
(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)
8-2. Method of Auto Component Color Balance1) Input the Component 720p 100% Color Bar signal into
Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means complete adjustment
9. Auto RGB Color Balance
9-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator, Master (MSPG-925FA), etc.
(Which has XGA 60Hz PC Format output with standard(0.7Vpp) horizontal black and white pattern as Fig.10)
9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz horizontal black and white
pattern into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
9. Default V alue in Adjustment mode
9-1. Auto Color Balance (Component/RGB)
9-2. White Balance
Level : 0
Level : 255
(Fig. 9) Auto RGB Color Balance Test Pattern
(Fig. 10) Default Value on OSD
(Fig. 10-1) Default Value on OSD
Auto Color Balance(Hex)
Auto-RGB G To SetRed Offset1 22Green Offset1 24Blue Offset1 23Red Offset2 45Green Offset2 43Blue Offset2 37Red Gain 14Green Gain 31Blue Gain 11Reset G To Set
White Balance(Hex)
Red Gain 82Red Offset 7AGreen Gain 86Green Offset 7FBlue Gain 7EBlue Offset 80Reset G To Set
(Fig. 8) Auto Component Color Balance Test Pattern
- 15 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
Is it identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
Doeshigh tension
output voltage Dropoccur?
When theY B/D Module
input connector isremoved, does output
voltage dropoccur?
When theY, Z B/D Module
input connector is remove,does Power Board hightension
output voltage Dropoccur?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule output circuit
Yes
When theZ B/D Module
input connector isremoved, does output
voltage Drop occurs?
11. Check the Y B/DModule output circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
- 16 -
1-2. Sony Power Board Structure
1 2 3
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
- 17 -
1-3. Sanken, LG INNOTEK Power Board Structure
1 2 3
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
- 18 -
2. No Power
(1) Symptom¯ Does’t minute discharge at module. ¯ Non does not come in into the front LED.
(2) Check following
Is plug in power cord? Plug in power cord.
Yes
No
Is the Line Filter and PowerBoard Cable connected?
Connect the Cable.
Yes
No
Is the Fuse(F101) onPower Board normal?
Replace the Fuse.
Yes
No
Is the Power Board and 7P ofVSC Board Cable connected?
Connect the Cable.
Yes
No
After the cable connect is remvedto Power Board(except the CN101connection cable), the AC voltagemarking is authorized on manual.When ST-BY 5V is not operated,replace Power Board.
- 19 -
3. Protect Mode
(1) Symptom¯ After once shining, it does not discharge minutely
from module¯ The Rely falls(The sound is audible “click”) ¯ It is converted with the color where the front LED
is red from green.
(2) Check following
Is the Power Boardnormal ?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Boardnormal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?
Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z-Boardnormal?
Is the output voltagenormal after removeP1 connector of Z-
B/D?
Is the Fuse (FS1, FS2) on Z-B/Dnormal? (In case of open is replace)
Yes
No Yes
Is the X- Boardnormal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, 1100 normaloperation: Replace VSC Board
Yes
No
Is the COF of X, Y, Znormal ?
No
Yes
Yes
- 20 -
4. No Raster
(1) Symptom¯ Does’t minute discharge at module. ¯ It maintains the condition where the front LED is green.
(2) Check following
Is the Power Boardnormal?
Replace thePower Board.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Board normal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?
Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) normal on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z- Board normal?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is the Fuse(FS1, FS2) normal onZ-B/D? (In case of open is replace)
Yes
No Yes
Is the X- Board normal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace the Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, P1100 normaloperation: Replace the VSC Board
Yes
No
Is the COF of X, Y, Znormal?
No
Yes
Yes
- 21 -
5. In case of occurring strange screen into specific mode
5-1. In case the OSD does not displayed
(1) Symptom¯ LED is green¯ The minute discharged continuously becomes accomplished from module
(2) Check following
Is the LVDS cablenormal ?
Is the VSC Boardnormal?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Does the FIL8532 IC(IC800) Operates ?
Replace FIL8532IC(IC800).
No
Is the Ctrl Board ofModule normal?
Replace Ctrl B/D.No
No
YesReplace VSC B/D
Replace the cable.Yes
- 22 -
5-2. In case of does’t display the screen into specific mode
(1) Symptom¯ The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).
(2) Check following¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
(5) In the case of becomes unusual display from Component, RGB mode
(6) In the case of becomes unusual display from HDMI mode
Is the Tuner normal?
Is the CXA2069Qnormal?
Is the Tuner Cableconnected well?
Cable inserts well.Yes
No
No
Yes
Is the FIL8532normal?
Replace the Tuner
No
Is the Input voltage, IIC Communicationand CVBS output normal?
Yes
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace the IC
No
Is the CXA2069Qnormal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Sil9011normal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
- 23 -
6. In case of no sound
(1) Symptom¯ LED is green¯ Screen display but sound is not output
(2) Check following
Is the SPK cablenormal?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Replace IC400
No
Replace IC401
No
Replace SPK cableYes
Yes
Is the RF/ AV/Component/ RGB/
HDMI sound normal?
No Does IC400Operates ?
Does IC401Operates ?
Replace IC402
No
Does IC402Operates ?
Replace VSC B/D
Yes Yes
- 24 -
BLOCK DIAGRAM
cabl
e
MEMO
- 25 -
- 26 -
EXPLODED VIEW
300
301
304
302
202206
203
204
201
205
580
410
530
121
601600
120
501
401
400
303
207
200
520
430
- 27 -
120 6401VD0032A SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX30 FILM TYPE
121 6401VD0033A SPEAKER ASSEMBLY, FULL RANGE(L) RZ-42PX30 FILM TYPE
200 6348Q-E080N PDP, 42” 852*480 PDP42V70102.AKLGG
201 6871QCH053A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V7 FPGA
202 6871QDH084A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV TOP B/D
203 6871QDH085A PWB(PCB) ASSEMBLY,DISPLA YDRV ASSY HAND INSERT 42V7 YDRV BTM B/D
204 6871QLH047A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V7 XL B/D
205 6871QRH055A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V7 XR B/D
206 6871QYH036A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V7
207 6871QZH041A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V7
300 3091V00816B CABINET ASSEMBLY, RZ-42PX31 STEREO MF056C FILM TYPE
3091V00816E CABINET ASSEMBLY, 42PX3RVC STEREO MF056C FILM TYPE 1 TONE SILVER
301 4980V01203A SUPPORTER, ASSY AL FILTER TOP RZ-42PX30
302 4980V01204A SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX30
303 4980V01205A SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX30
304 4980V01206A SUPPORTER, ASSY AL FILTER LEFT RZ-42PX30
400 3809V00605A BACK COVER ASSEMBLY, 42PX17/30 NON CHASSIS CHANGE
3809V00605E BACK COVER ASSEMBLY, CHASSIS CHANGE WARNING LABEL LGEAP
401 3301V00085B PLATE ASSEMBLY, ASSY 3300V00552B RT-42PX17 PLATE TUNER COVER
410 4980V01071A SUPPORTER, ASSY AL MODULE VER. RZ-42PX10
430 3501V00216C BOARD ASSEMBLY, ASSY AP-42DX30 MF056C NON
501 3301V00083A PLATE ASSEMBLY, ASSY 3300V00550A 3301V00084A 42PX17/30 PLATE TUNER
520 6871VMMF21A PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX4RV-TA/42PX3RV-TA
6871VMMF60A PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX3RV-TA FOR AUSTRALIA
530 6871VSMS36A PWB(PCB) ASSEMBLY,SUB CONT MF056C RZ-42PX30
580 6709V00010A POWER SUPPLY ASSEMBLY, 350W YPSU-J006A LG INNOTEK PSU ASSY
600 6871VSMS18B PWB(PCB) ASSEMBLY,SUB A/V MF056A RT/RZ-42PX40 SIDE A/V SUSAB
601 4811V00118B BRACKET ASSEMBLY, DECO RU-42PX10 RF043A SIDE AV
EXPLODED VIEW PARTS LIST
No. Part No. Descriptions
NSP-2100A,LF NEOFIDELITY TQFP 64P R/TP
AT24C02N-10SI-2.7 ATMEL 8P SOIC
24LC256-I/SM 8P,SOP TP 256K IIC SERIAL
AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP
AT24C32AN-10SI-2.7 ATMEL 8PIN SOP
SST25VF040-20-4C-S2AE-T SST SOIC 8P
24LC256-I/SM 8P,SOP TP 256K IIC
AT49BV160-70TI ATMEL 48P TSOP
K4D261638F-LC50,LF TSOPII 66P
K4D261638F-LC50,LF TSOPII 66P
CXA2069Q QFP64 BK I2C BUS AV S/W
MSP4410K MICRONAS 80P/PQFP
TAS5122DCAR 56P/TSSOP R/TP 30W
FLI8125BB-LF GENESIS 208P/PQFP
FLI8532BD-LF GENESIS 416P/PBGA
SII9011CLU(PB FREE) SILICON IMAGE 128P
ICL3232CBNZ INTERSIL 16P/SOP R/TP
MIC39100 MICREL 3P SOT223 R/TP
BA033FP-E2 ROHM 3P-SOP,TO252-3
KA7809R, FAIRCHILD 2P D-PAK, R/TP
SC156515M-1.8TR 5P/TO-263-5
BA033FP-E2 ROHM 3P-SOP,TO252-3
BA033FP-E2 ROHM 3P-SOP,TO252-3
BA033FP-E2 ROHM 3P-SOP,TO252-3
MIC39100 MICREL 3P SOT223 R/TP
SC156515M-1.8TR 5P/TO-263-5
KIA78R05F KEC 5PIN DPAK R/TP 1A,5V
SC156515M-1.8TR 5P/TO-263-5
MIC39100 MICREL 3P SOT223
BA033FP-E2 ROHM 3P-SOP,TO252-3
MC34063ADR2G ON SEMI SO-8P
KA4558D 8SOP OP AMP
LA7217M MFP14 TP SYNC SEPARATOR
74HC14D 14SOP TP SHITTER TRIGGER
74HC14D 14SOP TP SHITTER TRIGGER
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q301
Q302
Q303
Q304
Q400
Q401
Q402
Q403
Q404
Q407
Q409
Q410
Q411
IC1202
IC1203
IC200
IC201
IC503
IC504
IC505
IC506
Q102
Q200
Q203
Q204
Q207
Q305
Q405
Q406
Q408
D1012
D1013
D503
D504
D505
D506
ZD300
ZD301
ZD600
D1005
D1006
D1007
D1008
D1009
D1010
D106
D107
D108
D109
D1100
D1104
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR102008AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR102008AA
0TR102008AA
0TR102008AA
0DD200009AF
0DD200009AF
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
KRA102S R/TP KEC SOT23 CHIP TR
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
KRA102S R/TP KEC SOT23 CHIP TR
KRA102S R/TP KEC SOT23 CHIP TR
KRA102S R/TP KEC SOT23 CHIP TR
RU2M V(1) TP SANKEN
RU2M V(1) TP SANKEN
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
LOCA. NO PART NO DESCRIPTION
IC401
IC1201
IC1302
IC500
IC701
IC703
IC802
IC900
IC901
IC902
IC300
IC400
IC402
IC700
IC800
IC1200
IC600
IC1000
IC1001
IC1002
IC1003
IC1004
IC1005
IC1100
IC1101
IC1102
IC1103
IC1104
IC1105
IC1106
IC202
IC403
IC301
IC404
IC502
Q100
Q1000
Q1001
Q1002
Q1003
Q1004
Q101
Q101
Q102
Q1200
Q201
Q202
Q205
Q300
0ILNR00015A
0IMMRAL014B
0IMP242560A
0IMMRAL014B
0IMMRAL025A
0IMMR00004A
0IMP242560A
0IMMRAL016D
0IMMR00002A
0IMMR00002A
0ISO206900A
0IMCRMN028B
0IMCRTI028C
0IMCR02006A
0IMCR02005A
0IPRPS5005A
0IPRP00009A
0IPRPML001A
0IMCRRH001A
0IMCRFA010A
0IPMG00027A
0IMCRRH001A
0IMCRRH001A
0IMCRRH001A
0IPRPML001A
0IPMG00027A
0IPMGKE030A
0IPMG00027A
0IPRPML001A
0IMCRRH001A
0IPMGON013B
0ISS455880A
0ISA721700C
0IPH741400E
0IPH741400E
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
IC
TRANSISTOR
- 28 -
DIODE
- 29 -
LOCA. NO PART NO DESCRIPTION
D1105
D1106
D1107
D1109
D1110
D1200
D1201
D200
D300
D500
D501
D502
ZD400
C103
C1230
C1231
C1411
C315
C318
C319
C320
C321
C325
C451
C456
C1000
C1005
C1007
C1009
C1010
C1019
C1022
C1030
C1043
C1046
C1047
C1050
C1051
C1064
C1065
C1066
C1067
C1068
C1069
C1071
C1073
C108
C1082
C1083
C1084
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DS113379BA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DZRM00248A
0CE4763F618
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK105DF64A
0CK105DF64A
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE227SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS184 TP KEC - 85V 300MA
1SS133 T-72 TP ROHM KOREA DO34 90V
KDS184 TP KEC - 85V 300MA
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
RLZ8.2B-TE11 ROHM R/TP LLDS(LL-34)
47UF SRE 16V M FL TP5
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
LOCA. NO PART NO DESCRIPTION
C1085
C1087
C1098
C1099
C1102
C1105
C1107
C1108
C1110
C1115
C1116
C1117
C1118
C1119
C1120
C1126
C113
C1135
C1136
C1137
C1138
C114
C1148
C1149
C115
C1150
C1151
C1154
C1159
C1162
C1165
C1166
C1185
C1186
C1187
C1188
C1189
C1190
C1191
C1192
C1193
C1195
C1199
C1200
C1201
C1225
C1245
C1247
C1302
C1304
C1306
C1309
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE477DJ618
0CE477SF6DC
0CE227VF6DC
0CE477SF6DC
0CE477DJ618
0CE227VF6DC
0CE477SF6DC
0CE106SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE476SF6DC
0CE107SF6DC
0CE227SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
47UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF STD 35V 20% FL TP 5
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF STD 35V 20% FL TP 5
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
220UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
CAPACITOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 30 -
LOCA. NO PART NO DESCRIPTION
C1311
C1312
C1313
C1314
C1315
C1316
C1317
C1318
C1405
C1406
C1410
C1414
C1417
C1417
C1418
C1418
C1423
C1424
C1427
C1428
C1431
C1432
C1436
C1437
C1506
C203
C204
C208
C210
C211
C214
C215
C221
C238
C241
C300
C304
C305
C307
C327
C329
C337
C402
C403
C413
C418
C422
C425
C437
C444
C457
C462
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE475SK6DC
0CE476SK6D8
0CE475SK6DC
0CE476SK6D8
0CE106SH6DC
0CE106SH6DC
0CE227VF6DC
0CE227VF6DC
0CE106SH6DC
0CE106SH6DC
0CE227VF6DC
0CE227VF6DC
0CE476SF6DC
0CE475SK6DC
0CE477SF6DC
0CE477SF6DC
0CE475SK6DC
0CE477SF6DC
0CE106SF6DC
0CE475SK6DC
0CE477SF6DC
0CE107SF6DC
0CE476SK6D8
0CE107SF6DC
0CE226SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE476SF6DC
0CE226SF6DC
0CE335VK6DC
0CE107SF6DC
0CE106SF6DC
0CE226SF6DC
0CE106SF6DC
0CE107SF6DC
0CE335VK6DC
0CE107SF6DC
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
47UF MVG,MC 50V 20% SMD TAPPING
4.7UF MVG 50V 20% SMD R/TP
47UF MVG,MC 50V 20% SMD TAPPING
10UF MVG 25V 20% SMD R/TP
10UF MVG 25V 20% SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
10UF MVG 25V 20% SMD R/TP
10UF MVG 25V 20% SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
47UF MVG 16V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
4.7UF MVG 50V 20% SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
47UF MVG,MC 50V 20% SMD TAPPING
100UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
1UF MVG 50V 20% SMD R/TP
1UF MVG 50V 20% SMD R/TP
47UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
3.3UF MV 50V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
22UF MVG 16V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
3.3UF MV 50V 20% R/TP(SMD) SMD
100UF MVG 16V 20% SMD R/TP
LOCA. NO PART NO DESCRIPTION
C463
C464
C465
C480
C481
C482
C495
C527
C610
C728
C729
C730
C731
C735
C737
C739
C745
C750
C752
C760
C762
C764
C767
C771
C832
C833
C834
C835
C836
C837
C838
C839
C840
C851
C853
C884
C896
C901
C904
C905
C930
C943
C950
C483
C484
L1000
L1101
L1102
L1103
L1104
0CE106SF6DC
0CE106SF6DC
0CE106SK6DC
0CE108DJ618
0CE475SK6DC
0CE475SK6DC
0CE108DJ618
0CE476SF6DC
0CE107SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CF4741L438
0CF4741L438
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 50V 20% SMD R/TP
1000UF STD 35V 20% FL TP 5
4.7UF MVG 50V 20% SMD R/TP
4.7UF MVG 50V 20% SMD R/TP
1000UF STD 35V 20% FL TP 5
47UF MVG 16V 20% SMD R/TP
100UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
COIL
- 31 -
LOCA. NO PART NO DESCRIPTION
L404
L405
L406
L407
C1
C2
C3
C4
C5
C6
C7
JK500
JK601
AR1200
AR1201
AR1202
AR1203
AR1204
AR1205
AR700
AR701
AR702
AR703
AR704
AR705
AR806
AR806
AR807
AR807
AR808
AR808
AR809
AR809
AR810
AR810
AR811
AR811
AR812
AR812
AR813
AR813
AR814
AR814
AR815
AR815
AR816
AR816
AR817
6140VB0032A
6140VB0032A
6140VB0032A
6140VB0032A
387-J12N
6631V00020J
6631V00045B
6631V25083A
6631V39013N
6631V39022D
6631V39023D
6630G70016A
6630G70017A
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
0RRZVTA001B
0RRZVTA001D
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
DBF-1015A 15.5UH 10PIE DIGITAL AUDIO
12P 2.5MM 900MM H-H UL1185AWG26
3P 3.96MM 400MM H-W UL1672 AWG18
10P SPECIAL 150MM H-H UL1007AWG24
7P 2.5MM 100MM H-H UL1007 AWG24
8P 3.96MM 900MM H-H UL1617AWG22
4P 3.96MM 250MM H-H UL1007AWG18
10P 3.96MM 250MM H-H UL1007AWG18
A03-7071-094 SPG 15P 2.29MM
A02-0915-101 SPG 9P 2.54MM RS232
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
MNR14-E0A-J-510 R OHM 51 OHM 5%
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
LOCA. NO PART NO DESCRIPTION
AR817
R230
D1003
D1101
D1102
D1103
D1104
LD101
SW101
SW102
SW103
SW104
SW105
SW106
SW107
SW108
SW700
SW800
L100
L1004
L1005
L1006
L1007
L1008
L1009
L101
L1010
L1011
L1012
L1013
L1014
L1015
L1016
L1017
L1018
L1019
L102
L1020
L1021
L1022
L1023
L1024
L1025
L103
L109
L110
0RRZVTA001B
0RD0331H609
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL200000CA
140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
140-315A
6600VR1004A
6600VR1004A
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200JB8010L
6200JB8010L
MNR14-E0A-J-510 R OHM 51 OHM 5%
3.3 OHM 1/2 W 5.00% TA52
SAM2333 GREEN:10MCD, RED:6MCD
SAM2333 GREEN:10MCD, RED:6MCD
SAM2333 GREEN:10MCD, RED:6MCD
SAM2333 GREEN:10MCD, RED:6MCD
SAM2333 GREEN:10MCD, RED:6MCD
SAM5670(DL-2LRG) BK Y-GREEN
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
TACT SKHV17910B LG C&D 12V
SKHMPW 5P CHIP TACT J-ALPS .V .A
SKHMPW 5P CHIP TACT J-ALPS .V .A
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
SWITCH
FILTER & CRYSTAL
LED
RESISTOR
CONNECTOR
- 32 -
LOCA. NO PART NO DESCRIPTION
L1105
L1106
L1107
L1108
L1109
L111
L1110
L1111
L1112
L1113
L1115
L1116
L1117
L1118
L1119
L1120
L1121
L1122
L1123
L1125
L1126
L1127
L1128
L1129
L1130
L1204
L1205
L1206
L1207
L1208
L1209
L200
L201
L202
L203
L204
L300
L301
L302
L400
L401
L402
L403
L408
L409
L414
L415
L416
L417
L500
L502
L503
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200JB8010L
6200J000013
6200J000013
6200J000013
6200J000013
6200J000013
6200JB8010L
6200JB8010L
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
MLB-201209-1000L-N2 MAG LAYERS
LOCA. NO PART NO DESCRIPTION
L506
L604
L900
X300
X1200
X400
X700
X800
JK101
JK1200
JK502
JK600
JK100
JK101
JK102
JK400
A1
A2
A3
A4
A5
A6
C10
C8
C9
PA101
TU200
TU201
6200J000013
6200J000013
6200J000013
166-E02F
6212AB2845A
156-A02M
6212AB2844A
6212AB2844A
6613V00026A
6612B00015B
6612F00087A
6612F00087A
6612J00040B
6612J10012A
6612J10012A
6612J00037A
3828VA0545A
6710V00126R
6410VSH001D
4972V00178A
366-017A
486-395C
6851V00022C
6850J00005B
6850VA0004J
6712000002B
6700MF0010B
6700MF0010A
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
MLB-321611-0500P-N2 MAG LAYERS
RESONATOR,CERAMIC CSBLA500KECZF09-B0
RESONATOR,CRYSTAL ABLS-27.000MHZ
RESONATOR,CRYSTAL HC49U 18.432MHZ
RESONATOR,CRYSTAL ABLS-19.6608MHZ
RESONATOR,CRYSTAL ABLS-19.6608MHZ
UJB-03-28A UGCOM 6613V00004S
DC1R019WDH JAE 0.5MM,19PIN+2PIN
UEJ-CV-032 UGCOM EAR JACK 10MM
UEJ-CV-032 UGCOM EAR JACK 10MM
UJB-06-23B UGCOM 6P RCA+1P
UJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELD
UJB-05-02C GR/BL/RD/WH/RD 1*5 SHIELD
UJB-02-12A UGCOM 2P RCA VERTICAL+SHIELD
MANUAL,OWNERS MF056A NEU/42PX3RV
REMOTE CONTROLLER,RF043A PIP RZ-42PY20 40
POWER CORDAU10S3+V1625 SAA 2800MM
FIXERWALL ASSY PDP SET
PIN,DRAWINGSUB STAPLE NO.10 D0.3 L1 .
CARDLG LGEAP 1YR PDP/PRJT
CABLE,COAXIAL COAXIAL(150MM),UL1365#26 VW-1
CABLE,DVI LVDS UL20276 AWG30 500MM 3C
CABLE,COAXIAL UL1365#26 150MM UCA-EX-069
REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1
TUNER TAFM-W502P LFS MINI 4SYSTEM SUB
TUNER TAUM-W501P MINI 4 SYSTEM MAIN
ACCESSORIES
MISCELLANEOUS
JACK
PRINTED CIRCUIT BOARD
MAIN (TOP) MAIN (BOTTOM )
SIDE A/V(BOTTOM)
CONTROL
Apr., 2005Printed in KoreaP/NO : 3828VD0209R