16
Setup Reference guide for KX-NS1000 Version 4.22 Firmware “M-Net” SIP Trunk service (with Built-in Router) Version 1.0(PSCEU) 18.November, 2015
Setup Reference guide for KX-NS1000
Version 4.22 Firmware
“M-Net” SIP Trunk service
(with Built-in Router)
Version 1.0(PSCEU) 18.November, 2015
2
SUMMARY
This document is a reference for configuring “M-Net” SIP trunks with Panasonic KX-NS1000 systems
and includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation.
SIP trunk details such as account ID, authentication ID, password and DDI number will be provided
by M-Net.
Attention:
This document was created based on the results of test environment accounts.
Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of
completing this Inter-Operability Test Panasonic will provide technical support for any issues
experienced an assist as far as possible in providing a resolution.
Please obtain relevant information from Service provider before configuration of SIP trunks.
Panasonic will not be held liable for any information provided in this guidance document.
Information used in this document is for interoperability testing.
Information and Specifications in this document are subject to change without notice.
Note
[SIP Registration]
Deactivate a "Remove all binding when INS".
[Transfer Function]
SIP Server is Not supported a REFER method; Use a FWD to CO Transfer.
[FAX]
A G.711 Inband codec is supported. T.38 is not supported.
Table of Contents
(1) Provisioning a SIP trunk: Page 3
(2) Incoming Call Routing: Page 5
(3) Outgoing Call CLI: Page 6
(4) CLIR Outgoing Call (Withholding number): Page 7
(5) Call Forward Page 8
(6) Built-in Router and WAN settings: Page 10
(7) Packet Filtering Settings : Page 12
3
(1) Provisioning the SIP Trunk
SIP Trunk – Port Property
Move mouse over [V-SIPGW16] and click [Ous] and Select [Port Property]
SIP Trunk – Port Property continued
[Main] Tab
1. Channel Attribute: Basic Channel
2. Provider Name: Enter a name – reference only
3. SIP Server Location – Name: biz-int.m-call.de – (M-Net provided)
4. SIP Server Location – IP Address: Not required
5. SIP Server port Number: 5064 – (M-Net provided)
6. SIP Service Domain: Not required
7. Subscriber Number: Not required
4
SIP Trunk – Port Property continued
[Account] Tab
1. User name: Enter the SIP Account (User name) as supplied by M-Net.
(Note this is user name without @biz-int.m-call.de)
For example: SIP Account (User name) = +4989123456780
Enter: +4989123456780
2. Authentication ID: Enter the Authentication ID as supplied by M-Net.
(Note this is user name with @biz-int.m-call.de)
For example: Authentication ID =
Enter: [email protected]
3. Authentication Password: Enter the Authentication Password as supplied by M-Net.
For example: Authentication Password = Zzzzzzzzzz
Enter: Zzzzzzzzzz
SIP Trunk – Port Property continued
[Register] Tab
1. Register Ability: Leave enabled
2. Register Interval: Leave at 3600
3. Un-Register Ability: Disable
4. Registrar Server – Name: Not required
5. Registrar Server – IP Address: Not required
6. Registrar Server port number: Leave at 5060
5
(2) Incoming Call Routing
Go to [CO & Incoming call] and select [3.DDI /DID Table]
1. DDI/DID Number: Enter the DDI number in the format (as below)
Example: +49-89-12-34-56-78-0
Enter: 4989123456780
2. DDI/DID Name: Determined by the installer (optional setting)
3. DDI/DID Destination: Determined by the installer (extension number, group etc)
6
(3) Outgoing Call CLI
Move mouse over [V-SIPGW16] click [Ous] Select [Port Property] and [Calling Party] Tab
From Header – User Part: PBX-CLIP
Number Format: +International
Click [OK].
Go to [4.Extension, 1.Wired Extension, 1.Extension Settings] & select [CLIP]
[CLIP] tab
Enter a valid CLI number for each required extension in the CLIP ID field
Click [OK].
7
(4) CLIR Outgoing Call (Withholding Number)
There are 2 methods of CLIR Outgoing Call.
(4-1) CLIR Setting
Go to [4.Extension, 1.Wired Extension, 1.Extension Settings] & select [CLIP]
[CLIP] tab
1. CLIR: Enable
Move mouse over [V-SIPGW16] click [Ous] Select [Port Property] and [Calling Party] Tab
2. From Header – User Part: PBX-CLIP
3. Number Format: +International
(4-2) CLIR Outgoing dial with special code (*31*)
Using *31* to add in the top digit like in the following.
Make call dialed as *31* 08998765430
To: <sip:*31*[email protected]>
8
(5) Call Forward
Example case
Go to [2.System, 7.Class of Service, 1.COS Settings] & select [CO & SMDR]
[CO & SMDR] tab
Call Forward to CO: Enable
Move mouse over [V-SIPGW16] Select [Port Property] and [Advanced] Tab
[Advanced] tab
Diversion Header: Disable
Call FWD
CLI Number DDI Forward Number
09999123456 07777000001 05555000002
Original
(1st Caller)
PBX
DDI
Forwarded
(Called Party)
9
INVITE sip:[email protected] SIP/2.0
Via: SIP/2.0/UDP 192.168.0.101:35060;branch=z9hG4bKs4283fcd4f;rport
Max-Forwards: 70
Call-ID: [email protected]
From: <sip:[email protected]>;tag=1981099409
To: <sip:[email protected]>
CSeq: 1 INVITE
Allow: INVITE,ACK,CANCEL,BYE,PRACK,INFO,UPDATE,OPTIONS,REGISTER,NOTIFY
Supported: timer,100rel
User-Agent: Panasonic-MPR12-V004.22019/VSIPGW-V3.0000
Contact: <sip:[email protected]:35060>
Session-Expires: 1800
Content-Type: application/sdp
Content-Length: 268
Go to [4.Extension, 1.Wired Extension, 2.FWD/DND]
For example:
Select your Extension Number.
For external calls: Always (All)
Input prefix and forwarded number and #: 005555000002#
This is an example of FWD Invite packet from PBX.
Note: M-Net appends “P-Asserted-Identity” header in INVITE packet. Forwarded phone should
set to show CLIP “From header” because “P-Asserted-Identity” always included PBX DDI
CLIP.
10
(6) Built-in Router and WAN Settings
NS1000 has a Built-in Router and filtering functions (Ver3.2 or later) so advanced routing
configuration can be managed by the NS1000 and the internet router/modem simply providing
internet access.
Go to [Router Configuration]->[1.Setup]->[2.WAN]->[1.Connection Settings]
Select the appropriate the Connection Type.
In this example, we use the Static IP address option.
WAN IP Address: Enter your actual IP address.
Subnet Mask: Enter the appropriate subnet mask.
Gateway: Enter the actual Gateway IP address.
Preferred DNS IP Address: Enter the actual DNS IP address.
Alternative DNS IP Address: Enter the actual Alternative DNS IP address.
Click [Apply].
11
LAN Setting.
Go to [Network Service]->[1.IP Address/Ports]
Default Gateway: Blank
* Delete the “LAN Default Gateway IP address” if it’s entered IP address.
Note: NS1000 will work as the router, Not need the LAN Gateway.
DNS IP Address: Blank
* Delete the “Preferred DNS” and “Alternative DNS” if it’s entered IP address.
To use DNS address entered [Router Configuration], this field must be blank. .
Click [Apply]
Perform System Reset for changes to take effect.
12
(7) Packet Filtering Settings
Go to [Router Configuration] --> [2.Firewall] --> [2.Packet Filtering]
Click [Advanced Setting]
LAN->WAN Basic Policy: [Accept]
WAN -> LAN Basic Policy: [Discard]
Entry No.: Select [1]
Filter: Select [Enable]
13
Configure Filter 1, this is the setting pass through packet from M-Net server, port 35060.
Protocol Number: [Protocol Name] and choose [UDP]
TCP/UDP Source Port: /Port Number [Port Number] / [35060] -[ 35060]
TCP/UDP Destination Port /Number: [Port Number] / [35060] -[ 35060]
Source: [Address]
IP Address: [93.104.204.240] – Enter your assigned Server IP
Direction: [WAN->LAN]
14
Click [Apply]
Set Filter 2, this is the setting block packet from except M-Net server port 35060.
Click [Advanced Setting]
LAN->WAN Basic Policy: [Accept]
WAN -> LAN Basic Policy: [Discard]
Entry No.: Select [2]
Filter: Select [Enable]
15
Protocol Number: [Protocol Name] and choose [UDP]
TCP/UDP Source Port: [Any]
TCP/UDP Destination Port /Number: [Port Number] / [35060] -[ 35060]
Source: [Any]
Direction : [WAN->LAN]
Policy : [Discard]
Click [OK]
Go to following page.
16
Confirm the Packet Filtering Settings
