SONY DSR-PD100, PD100P SERVICE MANUAL VER 1.5 2003.05 (9-974-114-16)

DSR-PD100/PD100PRMT-811

SERVICE MANUAL

US Model Canadian ModelDSR-PD100

AEP ModelDSR-PD100P

Ver 1.5 2003. 05C MECHANISMPhoto: DSR-PD100

NTSC model: DSR-PD100 PAL model: DSR-PD100P

SPECIFICATIONS

Continued on next page

DIGITAL CAMCORDERMICROFILM

SUPPLIED ACCESSORIES Check that the following accessories are supplied with your camcorder.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

SAFETY CHECK-OUTAfter correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.

2. 3.

2

TABLE OF CONTENTS SERVICE NOTE1. 2. Power Supply During Repairs ............................................ 6 How to Take a Cassette Out When the Main Power Cannot Be Turned On ..................................................................... 6 Recording still images on memory sticks or PC cards memory photo recording ...................................................... 1-24 Viewing a still picture - memory photo playback ................ 1-25 Preventing accidental erasure - PROTECT .......................... 1-26 Deleting images ................................................................... 1-26 Copying the image recorded with the memory card slot to mini DVCAM tapes ............................................................. 1-27 Playing back images in a continuous loop SLIDE SHOW ...................................................................... 1-27 Additional information Compatibility of DVCAM and DV formats ........................ 1-28 Usable cassettes and playback modes .................................. 1-28 Charging the vanadium-lithium battery in the camcorder ... 1-29 Resetting the date and time .................................................. 1-29 Simple setting of clock by time difference .......................... 1-29 Tips for using the battery pack ............................................ 1-29 Maintenance information and precautions ........................... 1-30 Using your camcorder abroad .............................................. 1-31 Trouble check ...................................................................... 1-31 Self-diagnosis function ........................................................ 1-32 Identifying the parts ............................................................. 1-33 Warning indicators ............................................................... 1-35

SELF-DIAGNOSIS FUNCTION1. 2. 3. 3-1. 3-2. 3-3. 4. Self-Diagnosis Function ..................................................... 7 Self-Diagnosis Display ....................................................... 7 Service Mode Display ........................................................ 7 Display Method .................................................................. 7 Switching of Backup No. ................................................... 7 End of Display .................................................................... 7 Self-Diagnosis Code Table ................................................. 8

1.

GENERAL

Before you begin Using this manual .................................................................. 1-1 Checking supplied accessories .............................................. 1-1 Getting started Installing and charging the battery pack ................................ 1-1 Inserting a cassette ................................................................. 1-2 Basic operations Camera recording ................................................................... 1-3 Hints for better shooting ........................................................ 1-4 Checking the recorded picture ............................................... 1-5 Playing back a tape ................................................................ 1-5 Searching for the end of the picture ....................................... 1-6 Advanced operations Using alternative power sources ............................................ 1-6 Changing the mode settings ................................................... 1-6 Photo recording ...................................................................... 1-8 Shooting with all the pixels - PROG. SCAN ......................... 1-8 Using the FADER function .................................................... 1-8 Shooting with backlighting .................................................... 1-9 Using the wide mode function ............................................... 1-9 Enjoying picture effect ........................................................... 1-9 Recording with various effects - digital effect ..................... 1-10 Shooting with manual adjustment ....................................... 1-10 Using the PROGRAM AE function ..................................... 1-13 Focusing manually ............................................................... 1-14 Interval recording ................................................................. 1-14 Connecting the external microphone with the XLR connector .................................................................... 1-15 Attaching the supplied wide conversion lens ....................... 1-15 Superimposing a title ........................................................... 1-15 Making a custom title .......................................................... 1-16 Labelling a cassette .............................................................. 1-16 Watching on a TV screen ..................................................... 1-17 Viewing the picture with the picture effect .......................... 1-17 Viewing the picture with the digital effect ........................... 1-17 Searching the boundaries of recorded tape with date - date search ................................................................. 1-18 Searching the boundaries of recorded tape with title - title search .................................................................. 1-18 Searching for a photo - photo search/photo scan ................. 1-18 Display recording data - data code function ........................ 1-19 Editing onto another tape ..................................................... 1-19 Editing partially on a mini DVCAM tape DV synchro-editing .............................................................. 1-20 Recording from a VCR or TV ............................................. 1-20 Audio dubbing ..................................................................... 1-21 Memory card slot operations Using the memory card slot - introduction .......................... 1-21 Recording an image from a mini DVCAM tape as a still image ..................................................................... 1-23 Copying still images from a mini DVCAM tape photo save ............................................................................ 1-24

2.2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. 2-10. 2-11. 2-12. 2-13. 2-13. 2-14. 2-15.

DISASSEMBLYCabinet (Upper) Assembly, Front Panel Assembly ......... 2-1 Battery Panel Assembly ................................................... 2-2 Cabinet (R) Assembly, Cabinet (L) Assembly ................ 2-2 Mechanism Deck, Lens Assembly, VC-208, VI-151, SE-75 Boards ................................................................... 2-3 JK-163 Board .................................................................. 2-3 CK-80 Board ................................................................... 2-4 LCD Panel Assembly, Hinge Assembly .......................... 2-4 PD-101 Board .................................................................. 2-5 BT Terminal Board, DC-IN Connector ........................... 2-5 ED-48, VF-121 Boards .................................................... 2-6 LB-55 Board .................................................................... 2-6 MA-333 Board ................................................................ 2-7 DD-120, XL-2 Boards ..................................................... 2-7 Service Position (Mainly for and voltage measurement) ... 2-8 Circuit Boards Location .................................................. 2-9 Flexible Boards Location .............................................. 2-10

3.

BLOCK DIAGRAMS

3-1. Overall Block Diagram ................................................... 3-1 3-2. Power Block Diagram ..................................................... 3-5

4.

PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. Frame Schematic Diagram-1 ........................................... 4-1 Frame Schematic Diagram-2 ........................................... 4-5 4-2. Printed Wiring Boards and Schematic Diagrams ............ 4-9 CD-202 (CCD Imager) Schematic Diagram ............... 4-11 CD-202 (CCD Imager) Printed Wiring Board ............ 4-13 VC-208 (Sample Hold & AGC, Camera Processor, Base Band Input, Motor Drive, VAP Driver, Card Control, PWN Control, Honey, PCMCIA Control) Printed Wiring Board .................................... 4-17 VC-208 (Sample Hold & AGC)(1/7) Schematic Diagram ....................................... 4-24 VC-208 (Camera Processor)(2/7) Schematic Diagram ....................................... 4-27 VC-208 (Base Band Input)(3/7) Schematic Diagram ....................................... 4-32 VC-208 (Motor Drive)(4/7) Schematic Diagram ....................................... 4-35 SE-75 (YAW/Pitch Sensor) Printed Wiring Board .................................... 4-39

3

VC-208 (VAP Driver)(5/7) Schematic Diagram ....................................... 4-40 VC-208 (Card Control, PWM Control)(6/7) Schematic Diagram ....................................... 4-43 VC-208 (Honey, PCMCIA Control)(7/7) Schematic Diagram ....................................... 4-47 VI-151 (REC/PB AMP)(1/10) Schematic Diagram ....................................... 4-51 VI-151 (Timing Generator)(2/10) Schematic Diagram ....................................... 4-55 VI-151 (Video Interface)(3/10) Schematic Diagram ....................................... 4-57 VI-151 (DCT/IDCT)(4/10) Schematic Diagram ....................................... 4-62 VI-151 (Line Out)(5/10) Schematic Diagram ....................................... 4-65 VI-151 (Audio Processor)(6/10) Schematic Diagram ....................................... 4-68 VI-151 (HI Control)(7/10) Schematic Diagram ....................................... 4-71 VI-151 (Mechanism Control)(8/10) Schematic Diagram ....................................... 4-76 VI-151 (Drum/Capstan Motor Drive)(9/10) Schematic Diagram ....................................... 4-79 VI-151 (DC/DC Converter)(10/10) Schematic Diagram ....................................... 4-83 FP-594 (Loading Motor, S/T Reel Sensor) Printed Wiring Board .................................... 4-87 FK-4880 (User Control) Schematic Diagram ............. 4-88 VI-151 (REC PB AMP, Timing Generator, Video Interface, DCT/IDCT, Line Out, Audio Processor, HI Control, Mechanism Control, Drum/Capstan Motor Drive, DC/DC Converter) Printed Wiring Board .................................... 4-91 FP-21 (Focus SW) Flexible Board .............................. 4-96 FP-22 (MIC Jack) Flexible Board ............................... 4-96 MA-333 (Stereo MIC AMP) Printed Wiring Board .................................... 4-97 RI-10 (Sircs Receiver) Printed Wiring Board .................................... 4-98 MA-333 (Stereo MIC AMP) Schematic Diagram ....................................... 4-99 RI-10 (Sircs Receiver) Schematic Diagram ....................................... 4-99 FP-16 (Panel Switch) Flexible Board ...................... 4-103 FP-18 (User Control) Flexible Board ....................... 4-103 ED-48 (User Control) Schematic Diagram ............... 4-103 CK-80 (User Control) Schematic Diagram .............. 4-104 CK-80 (User Control) Printed Wiring Board ............ 4-107 ED-48 (User Control) Printed Wiring Board ............ 4-110 FP-23 (S Video) Flexible Board ................................ 4-111 JK-163 (Audio/Video IN/OUT) Printed Wiring Board and Schematic Diagram ..................................... 4-112 PD-101 (RGB Driver)(1/2) Schematic Diagram ..................................... 4-115 PD-101 (Timing Generator, Back-Light)(2/2) Schematic Diagram ..................................... 4-119 PD-101 (RGB Driver, Timing Generator, Back-Light) Printed Wiring Board .................................. 4-121 FP-19 (User Control) Flexible Board ....................... 4-121 VF-121 (Color EVF) Printed Wiring Board ............. 4-123 VF-121 (Color EVF) Schematic Diagram ................ 4-125 LB-55 (EVF Back-Light) Printed Wiring Board and Schematic Diagram ..................................... 4-128 XL-2 (MIC AMP) Printed Wiring Board and Schematic Diagram ..................................... 4-131

DD-120 (DC/DC Converter) Printed Wiring Board and Schematic Diagram ..................................... 4-134

5.

ADJUSTMENTS

5-1. Camera Section Adjustment ............................................ 5-1 1-1. Preparations before Adjustment (Camera Section) ......... 5-1 1-1-1. List of Service Tools ........................................................ 5-1 1-1-2. Preparations .................................................................... 5-3 1-1-3. Precaution ........................................................................ 5-5 1. Setting the Switch ............................................................ 5-5 2. Order of Adjustments ...................................................... 5-5 3. Subjects ........................................................................... 5-5 1-2. Initialization of F, E Page Data ........................................ 5-6 1. Initializing the F, E Page Data ......................................... 5-6 2. Modification of F, E Page Data ....................................... 5-6 3. F Page Table .................................................................... 5-6 4. E Page Table .................................................................... 5-9 1-3. Camera System Adjustments ......................................... 5-11 1. 27 MHz Origin Oscillation Adjustment (VC-208 Board) ............................................................. 5-11 2. IRIS & ND HALL Auto Adjustment ............................. 5-11 3. Offset Adjustment .......................................................... 5-12 4. Flange Back Adjustment ............................................... 5-13 4-1. Flange Back Adjustment (1) .......................................... 5-13 4-2. Flange Back Adjustment (2) .......................................... 5-13 5. Flange Back Check ........................................................ 5-14 6. Picture Frame Setting .................................................... 5-14 7. Pre White Balance Data Input ....................................... 5-15 8. Auto White Balance Standard Data Input ..................... 5-15 9. MAX GAIN Adjustment ............................................... 5-15 10. LV Standard Data Input ................................................. 5-15 11. White Balance ND Filter Compensation Adjustment ... 5-16 12. Auto White Balance Adjustment ................................... 5-16 13. Color Reproduction Adjustment (ND Filter OFF) ........ 5-16 14. Color Reproduction Adjustment (ND Filter ON) .......... 5-17 15. White Balance Check .................................................... 5-17 16. PSD Sensor Gain Adjustment ........................................ 5-18 16-1. PSD Sensor Gain Adjustment (1) .................................. 5-18 16-2. PSD Sensor Gain Adjustment (2) .................................. 5-19 17. Angular Velocity Sensor Sensitivity Adjustment .......... 5-20 1-4. Color Electronic Viewfinder System Adjustment .......... 5-21 1. VCO Adjustment (VF-121 Board) ................................ 5-21 2. Bright Adjustment (VF-121 Board) .............................. 5-22 3. Contrast Adjustment (VF-121 Board) ........................... 5-22 4. Backlight Consumption Current Adjustment (VF-121 Board) ............................................................. 5-23 5. White Balance Adjustment (VF-121 Board) ................. 5-23 1-5. LCD System Adjustment ............................................... 5-24 1. VCO Adjustment (PD-101 Board) ................................ 5-24 2. D range Adjustment (PD-101 Board) ............................ 5-25 3. Bright Adjustment (PD-101 Board) .............................. 5-25 4. Contrast Adjustment (PD-101 Board) ........................... 5-26 5. V-COM Level Adjustment (PD-101 Board) .................. 5-26 6. V-COM Adjustment (PD-101 Board) ............................ 5-27 7. White Balance Adjustment (PD-101 Board) ................. 5-27 5-2. Mechanical Section Adjustment .................................... 5-28 2-1. Parts Replacement and Preparation for Adjustment ...... 5-28 2-1-1. Outline ........................................................................... 5-28 1. Manual test .................................................................... 5-28 2. Step test ......................................................................... 5-28 3. Auto test ........................................................................ 5-28 2-1-3. Mode Selector II (A-6082-282-A) Connection ............. 5-28 2-1-2. Mechanism Condition (Position) Shifting Order List ... 5-28 2-1-4. The Mechanical Adjustment Requires the Following Tools ....................................................... 5-29 2-2. Parts Replacement ......................................................... 5-30 2-2-1. Tape Fall Stopper, HC Roller and HC Arm ................... 5-30 2-2-2. Drum Assembly and Drum Base Block Assembly ........ 5-30

4

2-2-3. Damper Assembly, Cassette Compartment Assembly and Extension Spring ........................................................... 5-31 2-2-4. Reel Table (S) / Reel Table (T) Assembly ..................... 5-32 2-2-5. Cassette Base Block Assembly, Gooseneck Gear Assembly and Relay Gear .................. 5-32 2-2-6. TG1 Adjustment Plate Assembly, Tension Coil Spring (TG1), TG1 Arm Assembly, TG7 Retainer Spring and TG7 Arm Block Assembly ... 5-33 2-2-7. Brake Slider Assembly, Pinch Slider Assembly and Cam Gear ....................................................................... 5-33 2-2-8. Pinch Arm Assembly, Torsion Spring (TG7LD), Pinch Press Arm and Eject Arm .................................... 5-34 2-2-9. GL Block Assembly, GL Driving Gear and HC Driving Arm ............................................................ 5-34 2-2-10. Capstan Motor, Conversion Pulley, Timing Belt and Holder .............................................. 5-35 2-2-11. L Motor Block Assembly and FP-594 Flexible Board ............................................... 5-36 2-2-12. Reset Arm (S), Brake (S), Brake Rack (S), Brake (T), Brake Gear (T), Brake Spring (T) and Extension Spring ......................................................... 5-37 2-2-13. Coaster (S) / (T) Assembly, GL Arm (S) / (T) Assembly, Guide Rail, GL Gear (S) / (T) and Torsion Spring (GLS) / (GLT) ..................................... 5-38 2-2-14. L Motor Assembly, Motor Shield, FP-248 Flexible Board, TG1 Spring Hook, Spring Hook Fulcrum Base, Spring Hook Driving Arm, Worm Shaft, Deceleration Gear and Motor Holder ..... 5-39 2-3. Check and Adjustment ................................................... 5-40 2-3-1. FWD Position Checking and Adjustment ..................... 5-41 2-3-2. FWD Back Tension Checking and Adjustment ............. 5-41 2-2-3. Reel Table (S) / Reel Table (T) Torque Check .............. 5-42 2-3-4. Preparation for Tape Path Checking and Adjustment .... 5-43 2-3-5. Track Checking and Adjustment ................................... 5-44 2-3-6. TG7 Slack Checking and Adjustment ........................... 5-44 2-3-7. Curl Checking and Adjustment ..................................... 5-45 2-3-8. CUE / REV Check ......................................................... 5-45 2-3-9. Rising Check ................................................................. 5-45 2-4. Periodic Check .............................................................. 5-46 2-4-1. Cleaning of Rotary Drum Assembly ............................. 5-46 2-4-3. Periodic Checks ............................................................. 5-46 2-4-2. Cleaning of Tape Path System ....................................... 5-46 5-3. Video Section Adjustments ........................................... 5-47 3-1. Preparations before Adjustments ................................... 5-47 3-1-1. Equipment Required ...................................................... 5-47 3-1-2. Precautions on Adjusting .............................................. 5-48 3-1-3. How to Enter Record Mode Without Cassette .............. 5-48 3-1-4. How to Enter Playback Mode Without Cassette ........... 5-48 3-1-5. Adjusting Connectors .................................................... 5-49 3-1-6. Connecting the Equipment ............................................ 5-49 3-1-7. Checking the Input Signals ............................................ 5-49 3-1-8. Alignment Tapes ............................................................ 5-50 3-1-9. Input/Output Level and Impedance ............................... 5-50 3-2. Initialization of B, C, D Page Data ................................ 5-51 1. Initializing the C Page Data ........................................... 5-51 2. Modification of C Page Data ......................................... 5-51 3. C Page Table .................................................................. 5-51 4. Initializing the D Page Data .......................................... 5-53 5. Modification of D Page Data ......................................... 5-53 6. D Page Table .................................................................. 5-53 7. Initializing the B Page Data ........................................... 5-55 8. Modification of B Page Data ......................................... 5-55 9. B Page Table .................................................................. 5-55 3-3. System Control System Adjustment .............................. 5-58 1. Battery End Adjustment (VI-151 Board) ...................... 5-58 3-4. SERVO AND RF SYSTEM ADJUSTMENT ............... 5-59 1. Cap FG Duty Adjustment (VI-151 Board) .................... 5-59 2 T Reel FG Duty Adjustment (VI-151 Board) ................ 5-59 3. PLL f0 & LPF f0 Adjustment (VI-151 Board) ............... 5-59

4. Switching Position Adjustment (VI-151 Board) ........... 5-60 5. AGC Center Level Adjustment (VI-151 Board) ............ 5-60 6. APC & AEQ Adjustment (VI-151 Board) ..................... 5-61 7. PLL f0 & LPF f0 Final Adjustment (VI-151 Board) ..... 5-61 3-5. Video System Adjustments ............................................ 5-62 3-5-1. Base Band Block Adjustments ...................................... 5-62 1. Chroma BPF fo Adjustment (VI-151 Board) ................ 5-62 2. S VIDEO OUT Y Level Adjustment (VI-151 Board) ... 5-62 3. S VIDEO OUT Chroma Level Adjustment (VI-151 Board) .............................................................. 5-63 4. AV OUT Y, Chroma Level Check (VI-151 Board) ....... 5-63 5. PLL Adjustment (VC-208 Board) ................................. 5-64 3-5-2. BIST Check .................................................................. 5-65 1. Playback System Check ................................................ 5-65 1-1. Preparation for Playback ............................................... 5-65 1-2. IC1814 (TRF) BIST (PB) Check ................................... 5-65 1-3. IC1601 (TFD) BIST (PB) Check .................................. 5-65 1-4. IC1600 (SFD) BIST (PB) Check ................................... 5-66 1-5. IC1501 (VFD) BIST (PB) Check .................................. 5-66 2. Recording System Check .............................................. 5-68 2-1. Preparations for recording ............................................. 5-68 2-2. IC1501 (VFD) BIST (REC) Check ............................... 5-68 2-3. IC1600 (SFD) BIST (REC) Check ................................ 5-68 2-4. IC1601 (TFD) BIST (REC) Check ............................... 5-68 2-5. IC1900 (TRX) BIST (REC) Check ............................... 5-69 3-6. Audio System Adjustments ........................................... 5-70 1. Playback Level Check ................................................... 5-71 2. Overall Level Characteristics Check ............................. 5-71 3. Overall Distortion Check ............................................... 5-71 4. Overall Noise Level Check ............................................ 5-71 5. Overall Separation Check .............................................. 5-71 5-4. Service Mode ................................................................. 5-72 4-1. Adjustment Remote Commander .................................. 5-72 1. Using the Adjustment Remote Commander .................. 5-72 2. Precautions Upon Using the Adjustment Remote Commander ............................ 5-72 4-2. Data Process .................................................................. 5-73 4-3. Service Mode ................................................................. 5-74 1. Setting the Test Mode .................................................... 5-74 2. Emergence Memory Address ........................................ 5-74 2-1. EMG Code (Emergency Code) ..................................... 5-74 2-2. MSW Code .................................................................... 5-75 3. Bit Value Discrimination ............................................... 5-76 4. Switch Check (1) ........................................................... 5-76 5. Switch Check (2) ........................................................... 5-77 6. Record of Use Check ..................................................... 5-77

6.

REPAIR PARTS LIST

6-1. Exploded Views ............................................................... 6-1 6-1-1. Overall Section ................................................................ 6-1 6-1-2. Mechanism Frame Section .............................................. 6-2 6-1-3. Cabinet (L) Section ......................................................... 6-3 6-1-4. Cabinet (R) Section ......................................................... 6-4 6-1-5. LCD Panel Section .......................................................... 6-5 6-1-6. Battery Panel Section ...................................................... 6-6 6-1-7. Cabinet (Upper) Section .................................................. 6-7 6-1-8. EVF Section .................................................................... 6-8 6-1-9. Front Panel Section ......................................................... 6-9 6-1-10. Lens Block Section ..................................................... 6-10 6-1-11. XLR Block .................................................................. 6-11 6-1-11. Cassette Compartment, Drum and Reel Table Assembly ................................. 6-12 6-1-12. Tape Guide, Pinch Slider Assembly and Brake Slider Assembly ........................................ 6-13 6-1-13. Each Gears and Loading/Capstan Motor Assembly ... 6-14 6-2. Electrical Parts List ....................................................... 6-15* The optical axis frame and color reproduction frame is shown on page 314 and 315.

5

SERVICE NOTE1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.

Method 1.Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the remote commander switch to the ADJ side.

Method 2.Press the battery switch of the battery terminal using adhesive tape, etc.

Method 3.Use the AC power adaptor.

2.

HOW TO TAKE A CASSETTE OUT WHEN THE MAIN POWER CANNOT BE TURNED ON

Note: To take a cassette out forcibly as follows when the main power cannot be turned on, remove the cassette lid, cabinet (L) and cabinet (R). Apply +4.5 V power from an external power supply to the loading motor, as shown below. Refer to sections 2-1 and 2-2 for the procedure to remove the cabinet (L) assembly.

Procedure: 1) Disconnect the CN2913 of VI-151 board. 2) Apply +4.5 V directly to the loading motor as shown to drive the loading motor that ejects a cassette.

Disconnect CN2913 of VI-151 board. Loading motor

DC power supply (+4.5V)

: loading : unloading

6

SELF-DIAGNOSIS FUNCTION1. SELF-DIAGNOSIS FUNCTION 2. SELF-DIAGNOSIS DISPLAY

When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.Viewfinder or LCD screenC:31:11

When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the repaired by:, block in which the problem occurred, and detailed code of the problem.LCD window

C : 3 1 : 11

Blinks at 3.2Hz

CRepaired by:

31Block

11Detailed Code

C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer

Refer to page 8. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.

3.3-1.

SERVICE MODE DISPLAYDisplay Method

The service mode display shows up to six self-diagnosis codes shown in the past.

While pressing the STOP key, set the switch from OFF to VTR or PLAYER, and continue pressing the STOP key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.Viewfinder or LCD screen[3] C : 3 1 : 1 1

LCD window

3 C : 3 1 : 11

Lights up

[3]Backup No. Order of previous errors

C:31:11Self-diagnosis Codes

Control dial

3-2.

Switching of Backup No.

By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time

3-3.

End of Display

Turning OFF the power supply will end the service mode display.Note: The self-diagnosis display data will be backed up by the coin-type lithium battery of CK-80 board BT7200. When this coin-type lithium battery is removed, the self-diagnosis display data will be lost by initialization.

7

4.Repaired by:

SELF-DIAGNOSIS CODE TABLESelf-diagnosis Code Block Detailed Function Code 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 2 3 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction

C C C C C C C C C C C C C C C C C C C C C C C

Condensation. Video head is dirty. Non-standard battery is used. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Difficult to adjust focus (Cannot initialize focus.)

Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Use the info LITHIUM battery. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin ! of CN500 of VC208 board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC500 of VC-208 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ! of CN500 of VC208 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC500 of VC-208 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE451 of SE-75 board) peripheral circuits. Inspect yaw angular velocity sensor (SE450 of SE-75 board) peripheral circuits.

E

6

1

0

0

E

6

1

1

0

Zoom operations fault (Cannot initialize zoom lens.) Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)

E

6

2

0

0

E

6

2

0

1

8

SECTION 1 GENERAL

DSR-PD100/PD100PThis section is extracted from instruction manual.

1-1

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

1-20

1-21

1-22

1-23

1-24

1-25

1-26

1-27

1-28

1-29

1-30

1-31

1-32

1-33

1-34

1-35E

SECTION 2 DISASSEMBLYNOTE: Follow the disassembly procedure as shown in the flow chart below.DSR-PD100/PD100P 2-1. Cabinet (upper) assembly, Front panel assembly 2-2. Battery panel assembly 2-3. Cabinet (R) assembly, Cabinet (L) assembly 2-4. @-@ SE-75 board 2-5 JK-163 board 2-6. CK-80 board 2-4. !-! VI-151 board 2-4. !-@ Mechanism deck

DSR-PD100/PD100P

2-4. 1-5 Lens assembly 2-4. 6-! VC-208 board

2-12. MA-333 board

2-10. ED-48 board 1-4 2-10. 5-! VF-121 board 2-11. LB-55 board

2-7. Hinge assembly 2-8. PD-101 board 2-9. BT terminal board DC-IN connector

NOTE: Follow the disassembly procedure in the numerical order given.

2-1. CABINET (UPPER) ASSEMBLY, FRONT PANEL ASSEMBLY

8 Cabinet upper block assembly (See page 2-6) 4 Screw (M2 4) lock ace P2

6 Flexible board CN7207 24P (CK-80 board) 5 FP-17 flexible board CN7203 6P (CK-80 board)

7 FP-10 flexible board CN2905 20P (VI-151 board)

3 Screw (M2 4) lock ace P2 1 Screw (M2 4), lock ace P2

9 Open the jack cover and remove the screw (M2 4).

2 Screw (M2 4) lock ace P2 a a ! FP-12 flexible board CN7304 26P (MA-333 board)

! Front panel assembly (Remove it while being careful of the claw a.) ! Two screws (M2 4), (See page 2-7) lock ace P2

2-1

2-2. BATTERY PANEL ASSEMBLY1 Screw (M2 4) 2 Two screws (M2 4) 3 Screw (M2 4) 9 Cable CN3200 4P (VI-151 board)

4 CPC cover

6 Battery panel assembly Remove it by opening to a side a little together with the cabinet (R) assembly

7 FP-18 flexible board CN7210 8P (CK-80 board) 8 Cable 3P, CN3201 3P (VI-151 board)

Cabinet (R) assembly

5 Three screws (M2 4)

2-3. CABINET (R) ASSEMBLY, CABINET (L) ASSEMBLY4Two screws (M2(step)) 5 Cassette lid 6 Screw (M2 4) 8Two screws (M2 3) 7 Screw (M2 4) 1-3 Cabinet (R) assembly 4-! Cabinet (L) assembly

! Control switch block (FK-4880), CN2907 18P (VI-151 board)

Mechanism deck, lens assembly1 FP-9 flexible board CN2906 60P (VI-151 board)

! Cabinet (L) assembly

9 Screw (M2 4) ! FP-12 flexible board CN2902 27P (VI-151 board)

3 Cabinet (R) assembly 2 FP-13 flexible board CN761 60P (VC-208 board)

2-2

2-4. MECHANISM DECK, LENS ASSEMBLY, VC-208, VI-151, SE-75 BOARDS1-5 Lens assembly 6-! VC-208 board !-! VI-151 board !-@ Mechanism deck @-@ SE-75 board @ MD frame assembly ! a flexible board (from capstan motor) CN2912 27P (VI-151 board) ! Screw (M2 4) ! b flexible board (from loading motor, S/T reel sensor) CN2913 27P (VI-151 board) @ Two screws ! c flexible board (from drum motor) (M2 step) CN2911 11P (VI-151 board) ! Screw ! d flexible board (from video head) (M2 step) CN1810 10P (VI-151 board) 4 Flexible board CN500 26P (VC-208 board) 3 Flexible board 51 -1 CN351 8P (VC-208 board) VI ARDBO

@ Mechanism deck

@ SE-75 board

!VC-208 board

@ Two screws (M2 4) @ FP-14 flexible board CN450 6P (ED-75 board)

SE BO-75 AR

D

d ! VI-151 board

c

b

a08 -2 VC ARD BO

@ Screw (M2 4) ! Two screws (M2 4)

1 CD-202 board CN200 40P (VC-208 board) 7 Three screws (M2 3)

5 Lens block

2-5. JK-163 BOARD1 FP-11 flexible assembly 2-6 JK-163 board 7-! Control switch block (FK-4880) !-@ FP-23 flexible board external connector (hot shoe) e

6 FP-14 flexible board CN400 6P (VC-208 board) 8 FP-8 flexible board 2 Two screws (M2 4) CN900 100P (VC-208 board) 9 FP-8 flexible board ! FP-12 flexible board CN2901 100P (VI-151 board) CN2902 27P (VI-151 board)

9 Screw (M2 4)

! Remove the FP-23 flexible board.

! Control switch block (FK-4880) flexible board Remove the d portion in the direction of b and remove the c and e portions in the arrow direction as shown without applying force to the a portion of the flexible board. a c

b @ External connector (hot shoe)

d e

! FK frame ! Tapping screw (B2 4) 8 Strap metal plate 7 Tapping screw (B2 4) ! Tapping screw (B2 4) ! S-terminal metal plate ! Two tapping screws (B2 4)

@ Shoe retainer @ Shoe reinforcement

! Remove the S-terminal.

4 J-K retaining metal plate

Shoe retainer Craw! While raising the shoe retainer in order to release the claw, push the shoe retainer in the direction of e to remove it. ! Four screws (M2 3) 6 JK-163 board 5 Screw (M2 3) 1 FP-11 flexible board CN7102 39P (JK-163 board) 2 FP-23 flexible board CN7101 14P (JK-163 board)JK BO 163 AR D

3 Four tapping screws (B2 4)

2-3

2-6. CK-80 BOARD1-4 PM slider assembly 5-! CK-80 board !-! Speaker

! Card ejector (Slide it in the direction Insert the craw into the slider of the arrow.) when re-assembling. 5 Two screws (M1.7 3) 6 Two screws

1 Screw (M2 3)

(M1.7 3)

! FP-9 flexible board CN7204 60P (CK-80 board)

2 PM cover

! Two screws (M2 3) ! Speaker fixing plate 8CK-80 board ! Speaker ! SP holder

! FP-16 flexible board CN7202 6P (CK-80 board) 7 Two screws (M1.7 3)

0 -8 CK ARD BO

! FP-13 flexible board CN7208 6P (CK-80 board) 9 Remove the ! Remove the harness harness. (SP-156) (CP-81, CP-82).

LCD panel assembly

! Four screws (M2 7)

4 PM slider assembly

3 Two screws (M2 3)

2-7. LCD PANEL ASSEMBLY, HINGE ASSEMBLY1-8 LCD panel block 9-! Hinge assembly ! Blind plate ! LCD hinge lid 9 Three screws (M2 3) ! Hinge assembly (Remove it in the direction of the arrow a.) ! Hinge cover (rear) (Remove it while being Craws careful of the craws.) ! Screw (M1.7 3)

Rotate it by 90 in the b direction of the arrow b.

2 Screw (M2 4) ! Three screws (M2 3) a 7 Two screws (M2 3) ! Hinge cover (front) 5 Remove the CP-81 harness. d 6Remove the CP-82 harness. ! Two screws (M1.7 3) 4 P cabinet (C) assemblyPD BO-101 AR D

Rotate it by 90 in the direction of the arrow c.

C

3 Screw (M2 4)

d

8 LCD panel block

Rotate it by 90 in the direction of the arrow d.

1 Two screws (M2 4)

2-4

2-8. PD-101 BOARD1-5 PD-101 board 6-8 FP-19 flexible board 9-! LCD panel

Craws! Light-conduction plate insulation sheet ! LCD module

! P cabinet (M) assembly

Craws9 Cold cathode fluorescent tube with light-conduction plate 2 Flexible board CN5701 10P (PD-101 board) 6 Panel frame (Remove it while being careful of the four craws.)

3 Flexible board (FP-55) CN5601 24P (PD-101 board) 7 Two screws (M2 3)PD BO-101 AR D

4 FP-19 flexible board CN5805 6P (PD-101 board) 1 Screw (M2 3) 5 PD-101 board

8 FP-19 flexible board

2-9. BT TERMINAL BOARD, DC-IN CONNECTOR1-3 BT terminal plate 4-6 DC-IN connector 7-! FP-18 flexible board

Battery panel assembly

1 Screw (M2 4)

3 BT terminal board

6 DC-IN connector

2 Strap metal plate

5 DC fixing plate

4 Two tapping screws (B2 5) 7 Two tapping screws (B2 5) ! FP-18 flexible board 9 AL knob 8 AL knob holder

2-5

2-10.ED-48, VF-121 BOARDS1-4 ED-48 board 5-8 EVF assembly 9-! VF-121 board !-! VF slide base ! VF click plate

! Slide here.

! VF slide base 4 Edit button ! Peel off the cushion.

! VF-121 board 3 ED-48 board 8 EVF assembly ! Release the craw. 9 FP-10 flexible board CN5001 21P (VF-121 board) 5 Four screws (M2 4) 6 Slider ground plate

! Release the two craws. ! FP-20 flexible board CN5101 30P (VF-121 board)

1 Four screws 7 Two screws (M2 3) (M2 4) 2 FP-17 flexible board CN7000 6P (ED-48 board)

2-11. LB-55 BOARD6 EVF cabinet (upper)

3 Two tapping screws (M2 4)

7 Eye cup assembly

! VF lens assembly (Remove it in the direction of the arrow a.) 9 Flexible board CN5202 16P (LB-55 board) a ! BL diffusion plate 4 EVF cabinet (lower) assembly

8 FP-20 flexible board CN5201 27P (LB-55 board) ! LCD cushion 1 ! LCD ! LCD cushion ! LCD cushion 1 Four tapping screws (M1.7 5) 5 VF slider assembly

! LB-55 board

2 Two tapping screws (M1.7 8)

2-6

2-12.MA-333 BOARD1-7 MA-333 board 8-0 FP-22 flexible board (MIC jack) !-! FP-21 flexible board ! MF retainer assembly ! MF reinforcement plate ! Screw (M2 3) ! Tapping screw (B2 5)

FP-21 flexible board

! Tapping screw (B2 5)

1 Sound insulation sheet

! Screw (M2 3)

! FP-21 flexible board

9 Tapping screw (B2 5)

2 FP-21 flexible board CN7302 10P (MA-333 board) 6 Cable (MIC) CN7300 2P (MA-333 board) 4 Two tapping screws (B2 5)

0 Jack retainer ! FP-22 flexible board (MIC jack) 7 FP-22 flexible board CN7303 5P (MA-333 board)MA BO -33 AR 3 D

5 Cable (MIC) CN7301 2P (MA-333 board) 3 FP-37 flexible board CN7305 6P (MA-333 board)

8MA-333 board

2-13.DD-120, XL-2 BOARDS2 Screw (+P 2.6 5)

Terminal box (upper)

1- ! DD-120 board !- ! XL-2 board !- ! XL-51 harness !, ! Hot shoe, plug connector ! Two tapping screws (B2 12) 8 Screw (M2 3) 3 Screw 9 Board holder (+P 2.6 5)

(+48 V)! Screw (M2 3)

When re-assembling, engage the knob of the ATT switch, +48 V with the groove of the button. (ATT)

! Board holder

! Screw (M2 3) 7 Screw (M2 3) ! DD-120 board 5 XL-51 harness CN201, 3 pin (DD-120 board) 1 Two screws (+P 2.6 5) ! XL-2 board 6 XL-51 harness CN101 (XL-2 board) 4 Terminal box (lower)

! Shoe retainer assembly ! XL-51 harness 8 pin (hot shoe plug)

! Hot shoe plate assembly

! Hot shoe plug connector (8 pin)

2-7

2-14. SERVICE POSITION (Mainly for check and voltage measurement)Firstly, remove the following parts referring to DISASSEMBLY (sections 2-1 to 2-6, 2-10 and 2-12), and connect parts as shown below.When the ED-48 board and LCD display panel are not needed during check and voltage measurement, this connection is not necessary. ED-48 board Lens block CD-202 board LCD display panel Base 1: Using a box or the like, support the lens block, CD-202 board and SE-75 board VC-208 board as shown. Extension Base 2: Using a box or the like, V cable BO C-2 support the VI-151 AR 08 (J-6082D board as shown. 431-A) Base 1 FP-14 FP-12 FP-13 a-80 RD CK OA B

PD-101 board

a b

LCD panel

Base 2

Control switch block (FK-4880) VF-121 board

Extension cable (J-6082432-A) MA-333 FP-73 board RI-10 board Extension cable (J-6082-433-A) Mechanism deck

FP-23

b1 -15 RD VI OA B

JK-163 board

FP-9 FP-10

EVF (LB-55 board, LCD) Battery case assembly

AC adapter

AC IN

Adjustment remote commander (RM-95)

2-8

2-15.CIRCUIT BOARDS LOCATION

LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF)

SE-75 (YAW/PITCH SENSOR)

ED-48 (USER CONTROL)

JK-163 (AUDIO/VIDEO IN/OUT) RI-10 (SIRCS RECEIVER) CK-80 MA-333 USER CONTORL, (STEREO MIC AMP) LCD DRIVE PD-101 (RGB DRIVER, TIMING GENERATOR, BACK-LIGHT)

XL-2 (MIC AMP) CD-202 (CCD IMAGER) DD-120 DC/DC CONVERTER

VC-208 SAMPLE HOLD & AGC, CAMERA PROCESSOR, BASE BAND INPUT, MOTOR DRIVE, VAP DRIVER, CARD CONTROL, PWM CONTROL, HONEY/PCMCIA CONTORL

VI-151 REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER2-9

2-16.FLEXIBLE BOARDS LOCATION

FK-4880 (USER CONTROL) FP-17 FP-23 (S-Y/C IN/OUT)

FP-18 (USER CONTROL)

For LED FP-16 FP-11 FP-13 FP-8


FP-20 FP-10 LENS BLOCK

FP-21 (FOCUS) FP-9

(From CAPSTAN MOTOR) From LOADING MOTOR, S/T REEL SENSOR (From DRUM MOTOR) FP-22 (MIC JACK) FP-12 FP-37 FP-14 (From VIDEO HEAD)

2-10E

SECTION 3 BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM

DSR-PD100/PD100P

3-1

3-2

3-3

3-4

DSR-PD100/PD100P

3-2. POWER BLOCK DIAGRAM

3-5

3-6

3-7

3-8E

SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS4-1. FRAME SCHEMATIC DIAGRAM-1

DSR-PD100/PD100P

4-1

4-2

4-3

4-4

FRAME SCHEMATIC DIAGRAM-1

DSR-PD100/PD100P



4-5XL-51 HARNESS8 SHOE UNREG SHOE UNREG SHOE ID1 MIC GND SHOE MIC L SHOE GND DD GND +46V DD UNREG 1 2 3 4 5 6 SHOE ID1 SHOE ID 2 SHOE MIC R MIC GND SHOE MIC L SHOE GND 7 LANC SIG SHOE UNREG SHOE ID1 MIC GND SHOE MIC L SHOE GND DD GND +46V DD UNREG 7 6 5 4 3 2 1 8 8 7 6 5 4 3 2 1 CN101 8P

XL-2 BOARD3 +46V DD GND DD UNREG CN201 3P 2 1

PLUG CONNECTOR

DD-120 BOARD

4-6 4-7 4-8

DSR-PD100/PD100P

DSR-PD100/PD100P

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMSTHIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)(For printed wiring boards) b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Through hole is omitted. Circled numbers refer to waveforms. There are few cases that the part printed on diagram isnt mounted in this model. Chip parts. Transistor DiodeC 65 4 45 6 4 5 1 2 3 3 3

(Measuring conditions voltage and waveform) Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. * (VOM of DC 10 MW input impedance is used.). Voltage values change depending upon input impedance of VOM used.) 1. Connection

Pattern boxB E 12 3 32 1 32 1 54 3 2 1 2 1 2 1

(For schematic diagrams) All capacitors are in F unless otherwise noted. pF : F. 50V or less are not indicated except for electrolytics and tantalums. Chip resistors are 1/10W unless otherwise noted. k=1000, M=1000k. Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520

95 cm

Front side of the lens

Kinds of capacitor Temperature characteristics External dimensions (mm) Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. Parts with 5 differ according to the model/destination. Refer to the mount table for each function. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. Signal name XEDIT EDIT PB/XREC PB/REC 2 : non flammable resistor 1 : fusible resistor C : panel designation A : B+ Line * B : B Line * J : IN/OUT direction of (+,) B LINE. * C : adjustment for repair. * Circled numbers refer to waveforms. * * Indicated by the color red.

2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.

Yellow

H

A B

A=B

Fig. a (Video output terminal output waveform)

White Magenta Red BlueB A Electron beam scanned frame CRT picture frame

Fig.b (Picture on monitor TV)3. The LINE REC waveform shows the waveform when the color for signal (video signal) is input from a color bar pattern. The LINE OUT waveform shows the waveform when the signals are connected to the S-VIDEO and VIDEO/AUDIO jacks but not to other jacks. When indicating parts by reference number, pleas include the board name.

Note : The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.

Note : Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

4-9

Yellow Cyan Green White Magenta Red Blue

Cyan Green

DSR-PD100/PD100P

CD-202 BOARDCAMERA REC

1 IC101 1, 2IC102 1, 2

IC100 1, 2

H

8.4Vp-p

2 IC102 3

IC100 3, IC101 3

22Vp-p V

3 IC101 !, !IC102 !, !

IC100 !, !

13.5 MHz

3.0Vp-p

4 IC102 !

IC100 !, IC101 !

13.5 MHz

3.0Vp-p

5 Q101 EH0.6Vp-p H

6 Q100 EH0.6Vp-p H

7 Q102 E

H

0.5Vp-p

CCD IMAGERCD-202

4-11

4-12

DSR-PD100/PD100P

DSR-PD100/PD100P

CD-202 (CCD IMAGER) PRINTED WIRING BOARD Ref. No. CD-202 Board; 10,000 Series

CD-202 BOARDC100 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C-5 C-5 F-5 A-5 D-5 F-5 A-5 C-5 C-5 C-5 C-6 A-5 A-6 E-5 A-6 A-5 A-5 F-5 F-5 F-5 E-5 CN100 B-1 IC100 IC101 IC102 L100 L101 L102 Q100 Q101 Q102 R100 R101 R102 R103 R104 R105 F-7 C-7 A-7 C-5 A-5 E-5 C-6 F-5 A-6 C-5 F-5 A-5 C-5 F-5 A-5

XL-2 (MIC AMP)

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts TransistorC

CD-202 (CCD IMAGER) DD-120 DC/DC CONVERTER

B

E


There are few cases that the part printed on this diagram isnt mounted in this model.VI-151 REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER

4-13

4-14

CCD IMAGERCD-202

4-15

DSR-PD100/PD100P

VC-208 (SAMPLE HOLD & AGC, CAMERA PROCESSOR, BASE BAND INPUT, MOTOR DRIVE, VAP DRIVER, CARD CONTROL, PWM CONTROL, HONEY, PCMCIA CONTROL) PRINTED WIRING BOARD Ref. No. VC-208 Board; 10,000 Series VC-208 BOARD (SIDE A)C228 C234 C235 C236 C237 C238 C239 C252 C253 C254 C255 C256 C257 C258 C259 C260 C300 C301 C500 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 C514 C515 C516 C517 C518 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C530 E-7 E-6 E-6 D-7 D-7 E-6 E-5 E-7 E-6 E-5 E-8 E-7 E-7 E-6 E-6 E-6 D-7 C-8 D-5 C-5 C-4 C-4 C-5 C-5 D-5 D-5 D-4 C-5 D-5 C-5 C-5 D-5 D-5 C-4 D-4 C-4 D-5 D-5 C-6 C-6 D-6 D-6 C-6 D-6 C-6 C-6 D-6 C531 C532 C533 C534 C701 C703 C704 C733 C734 C735 C736 C737 C738 C739 C740 C742 C743 C752 C753 C754 C760 C762 C763 C764 C765 C766 C767 C768 CN200 CN351 CN400 CN500 CN761 D500 D501 D721 D722 FB202 FB300 FB301 FB501 FB752 FB754 D-5 C-3 C-5 C-6 A-1 A-1 A-1 B-2 A-2 C-1 A-1 A-1 B-1 C-1 B-3 C-2 C-3 C-3 C-3 C-5 A-5 B-4 C-5 A-7 A-8 A-8 B-7 B-7 E-8 C-3 A-2 C-2 B-1 C-5 D-5 B-2 B-2 D-7 C-8 D-6 C-4 C-5 A-7 IC205 IC206 IC207 IC300 IC500 IC501 IC502 IC752 IC756 IC757 IC758 L201 L500 L501 L503 L721 L722 L723 L723 L724 L725 L726 L727 L751 L752 Q500 Q501 Q502 Q503 Q504 Q505 Q701 Q702 Q721 Q722 R201 R204 R205 R325 R326 R337 R338 R500 R501 D-8 D-7 D-6 C-7 C-4 C-5 C-6 B-3 B-5 B-6 B-8 E-6 D-4 C-4 D-5 B-2 B-2 B-1 C-2 B-1 B-3 C-1 C-2 C-4 A-8 C-4 C-5 C-5 D-5 C-6 C-4 A-1 A-3 B-2 B-2 D-7 D-5 D-6 B-8 B-8 C-6 C-6 C-3 C-4 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R518 R519 R520 R521 R522 R523 R524 R525 R526 R528 R529 R530 R531 R532 R533 R534 R535 R536 R537 R538 R539 R540 R541 R542 R543 R544 R545 R701 R702 R703 R704 C-5 C-3 C-5 C-5 C-5 C-5 C-5 C-5 D-5 C-5 D-5 D-5 C-5 D-5 D-5 D-5 C-5 C-5 C-5 C-5 C-5 D-5 D-6 C-6 C-6 C-6 C-6 D-6 C-6 D-6 D-6 C-6 D-6 D-6 D-6 C-6 C-6 C-6 C-6 C-6 C-3 D-5 C-4 A-1 A-1 A-1 A-1 R734 R735 R765 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776 R777 R778 R779 R780 R788 R789 R790 R791 R792 R800 R801 R802 R803 R807 R808 R810 R811 R900 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 R919 B-2 B-2 B-9 B-9 B-9 B-8 B-8 B-8 B-8 B-8 A-8 A-8 A-8 A-8 A-8 A-9 A-9 A-9 B-6 A-7 A-7 B-6 A-6 A-8 B-8 B-6 B-6 C-6 C-4 C-4 C-4 B-5 B-5 B-5 B-5 B-5 B-5 B-5 B-5 B-5 B-5 B-5 B-6

XL-2 (MIC AMP) CD-202 (CCD IMAGER) DD-120 DC/DC CONVERTER


For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts TransistorC 65 4

Diode3

BVI-151 REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER

E

12 3

2

1

There are few cases that the part printed on this diagram isnt mounted in this model.

CAMERA PROCESS & CNT, S/H &AGC, BASE BAND INPUT, LENS DRIVER, VAP SENSOR, FLASH DD/CNT, VAP DRIVERVC-208

4-17

4-18

DSR-PD100/PD100P

DSR-PD100/PD100P

VC-208 (SAMPLE HOLD & AGC, CAMERA PROCESSOR, BASE BAND INPUT, MOTOR DRIVE, VAP DRIVER, CARD CONTROL, PWM CONTROL, HONEY, PCMCIA CONTROL) PRINTED WIRING BOARD Ref. No. VC-208 Board; 10,000 Series VC-208 BOARD (SIDE B)C201 C202 C203 C204 C205 C206 C207 C208 C209 C211 C212 C213 C214 C215 C216 C216 C217 C218 C219 C220 C221 C222 C227 C229 C230 C231 C232 C233 C240 C241 C242 C243 C244 C245 C246 C247 C248 C249 C250 C261 C262 C302 C303 C305 C306 C307 C308 C309 C310 C311 C351 C353 C354 C355 C357 C358 C359 C360 C361 C362 C368 C370 C371 C372 C373 C374 C375 C376 C377 C379 C380 C381 C382 C383 C400 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 E-13 E-13 E-13 E-12 E-12 E-12 D-12 D-12 D-12 D-13 D-12 D-12 D-13 D-12 D-12 E-11 D-13 D-13 D-12 D-12 D-12 D-14 D-11 E-11 E-11 E-11 D-12 D-12 E-13 E-12 E-12 D-12 E-12 D-12 D-12 E-11 D-11 D-11 D-12 D-11 D-11 C-11 C-12 A-10 A-10 A-10 C-12 D-12 A-10 C-18 D-15 D-15 D-15 D-15 C-15 C-14 C-14 D-14 C-14 C-14 C-12 D-13 D-13 D-13 C-13 C-13 C-13 C-14 C-14 D-14 C-13 D-14 D-15 D-15 B-12 B-13 A-13 B-12 B-12 B-12 B-12 B-12 A-13 A-12 A-12 C411 C412 C413 C414 C415 C702 C705 C721 C722 C723 C724 C725 C726 C727 C728 C729 C730 C731 C732 C744 C751 C755 C756 C757 C758 C759 C761 C769 C770 C771 C772 C1200 C1201 C1202 C1203 C1204 C1205 C1206 C1207 C1208 C1209 C1210 C1211 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1219 C1220 C1221 C1222 C1223 C1224 C1225 C1226 C1227 C1228 C1229 C1230 C1231 C1232 C1233 C1234 C1235 A-12 B-13 B-12 B-12 B-12 B-17 A-18 B-18 B-17 B-18 B-18 B-18 B-17 B-18 B-18 B-18 B-18 C-18 C-17 B-17 B-13 C-13 B-14 B-14 C-14 B-15 A-13 C-12 C-12 C-12 A-14 B-16 B-16 B-16 B-17 A-16 B-16 A-15 B-16 B-16 A-16 B-16 A-16 B-14 A-15 A-15 B-16 A-15 A-15 A-15 A-16 A-16 A-15 A-15 A-16 B-16 B-15 B-16 B-16 B-16 A-16 B-16 B-15 B-14 B-15 B-15 C-15 IC302 IC305 IC351 IC352 IC354 IC355 IC356 IC357 IC400 IC701 IC721 IC722 IC751 IC753 IC754 IC755 IC759 IC760 IC1200 L200 L300 L301 L351 L352 L400 L754 L1200 L1201 L1202 L1203 L1204 L1205 Q200 Q201 Q301 Q351 Q352 Q353 Q354 Q727 Q751 Q752 Q753 Q754 Q755 Q1200 Q1201 Q1202 Q1203 Q1204 Q1205 Q1206 Q1207 Q1208 Q1209 R200 R202 R203 R207 R208 R209 R210 R211 R212 R213 R214 R215 R216 R217 R218 R219 R220 R221 R222 R223 R224 R225 R226 R227 R235 R236 R237 B-11 C-11 C-15 C-15 C-13 C-13 C-14 D-14 B-12 A-17 B-18 B-17 B-13 C-13 A-14 A-13 C-12 A-14 B-15 D-13 C-11 D-12 C-15 D-14 C-12 C-15 A-16 B-17 C-16 A-16 B-16 B-14 E-13 E-13 B-12 C-14 D-14 D-15 C-15 B-18 C-13 C-14 B-14 C-14 C-12 A-16 B-16 B-16 A-16 A-16 B-16 B-16 A-15 C-17 B-16 D-11 E-11 D-11 E-12 E-12 D-12 E-12 D-12 D-12 E-11 D-11 D-11 D-12 E-12 D-12 D-13 D-13 D-14 D-12 D-12 D-12 D-12 D-12 D-12 E-12 E-12 E-13 R300 R301 R302 R303 R304 R305 R306 R307 R308 R309 R311 R314 R316 R317 R318 R319 R320 R327 R328 R329 R330 R331 R332 R333 R334 R335 R336 R350 R353 R354 R355 R356 R357 R358 R359 R360 R361 R362 R363 R364 R365 R366 R367 R368 R369 R370 R371 R372 R373 R374 R375 R376 R377 R378 R379 R380 R381 R382 R383 R384 R385 R386 R387 R388 R389 R390 R391 R392 R393 R394 R395 R396 R400 R401 R402 R403 R404 R405 R406 R407 R408 R409 R721 R722 R723 B-11 B-12 B-12 C-11 B-11 B-11 B-11 B-11 B-11 C-11 B-11 A-10 A-10 A-10 B-10 B-12 B-10 A-11 A-11 A-11 A-11 B-10 A-11 A-11 A-11 A-11 A-11 C-13 D-14 D-14 D-14 D-14 C-15 D-15 C-15 D-15 D-15 C-15 D-15 C-15 D-15 D-15 D-14 D-14 C-14 C-14 C-14 C-14 C-14 C-13 D-13 D-14 C-13 D-13 D-13 C-13 C-13 C-13 C-13 D-13 D-13 D-13 C-14 C-14 D-16 C-16 D-15 D-15 C-14 C-14 D-14 D-13 B-12 B-13 B-13 B-12 B-12 B-12 B-12 B-13 B-12 B-12 B-18 B-18 B-18 R724 R725 R726 R727 R728 R729 R730 R731 R732 R733 R740 R741 R742 R743 R744 R745 R751 R752 R754 R755 R756 R757 R758 R759 R760 R761 R762 R763 R764 R781 R782 R783 R784 R785 R786 R787 R793 R794 R795 R796 R797 R804 R805 R806 R809 R911 R912 R913 R914 R915 R916 R917 R918 R920 R921 R922 R1202 R1203 R1204 R1205 R1206 R1207 R1208 R1209 R1210 R1211 R1212 R1213 R1214 R1216 R1217 R1218 R1219 R1266 R1267 R1268 R1269 R1270 R1271 X1200 X200 X300 X751 B-17 B-18 C-18 B-17 B-18 B-18 B-18 B-17 B-17 B-17 C-18 B-18 C-18 C-18 C-18 C-17 C-13 C-13 C-13 C-14 B-14 B-14 B-14 B-14 A-14 A-14 A-13 C-14 B-14 A-13 A-13 A-13 A-13 A-13 A-13 A-13 A-13 C-12 C-12 C-12 C-12 A-14 A-14 A-14 C-12 B-15 C-15 B-15 C-15 B-15 C-15 B-15 C-15 C-17 C-17 C-17 B-16 B-16 B-17 A-15 A-16 B-16 B-16 B-16 A-16 A-16 B-16 B-16 A-15 B-16 A-15 B-16 A-15 B-15 B-16 B-16 B-16 B-15 C-15 C-16 E-11 C-11 B-14

CN900 C-17 D204 D723 D724 D1200 D1201 FB200 FB201 FB203 FB204 IC203 IC204 IC208 IC301 E-11 C-18 C-18 C-16 C-15 D-12 D-11 E-13 E-14 D-13 D-11 D-14 C-11

4-19

4-20

CAMERA PROCESS & CNT, S/H &AGC, BASE BAND INPUT, LENS DRIVER, VAP SENSOR, FLASH DD/CNT, VAP DRIVERVC-208

DSR-PD100/PD100P

DSR-PD100/PD100P

For schematic diagram Refer to page 4-17 for printed wiring board.

VC-208 BOARD (1/7)1 IC203 @, @CAMERA REC

6 IC203 9CAMERA REC

0.6Vp-p H H

0.34Vp-p

2 IC203 #, #CAMERA REC

7 IC204 #CAMERA REC

27.0 MHz H 0.5Vp-p

3.4Vp-p

3 IC203 #, #CAMERA REC

8 IC204 $CAMERA REC/PB

13.5 MHz H 0.6Vp-p

3.0Vp-p

4 IC203 5CAMERA REC

9 IC205 1 5 , 8 !IC206 1 5 , 8 ! IC207 1 5 , 8 ! CAMERA REC0.28Vp-p

H

74 nsec

2.8Vp-p

5 IC203 7CAMERA REC

0.34Vp-p H

SAMPLE HOLD & AGCVC-208 (1/7)

4-24

4-25

4-26

DSR-PD100/PD100P

DSR-PD100/PD100P


VC-208 BOARD (2/7) ! IC300 &CAMERA REC/PB

3.0Vp-p 13.5MHz

! IC302 $CAMERA REC/PB

2.8Vp-p 20.0MHz

4-27

4-28

4-29

CAMERA PROCESSORVC-208 (2/7)

DSR-PD100/PD100P

DSR-PD100/PD100P


VC-208 BOARD (3/7) ! IC1200 @LINE REC (NTSC)

0.44Vp-p H

! IC1200 @CAMERA REC/PB

1.0Vp-p H

! IC1200 #LINE REC (NTSC)

H

0.5Vp-p

! IC1200 #CAMERA REC/PB

H

1.5Vp-p

! IC1200 #LINE REC (NTSC)

0.44Vp-p H

! IC1200 #CAMERA REC/PB

2.0Vp-p H

! IC1200 $LINE REC

40.5MHz

3.0Vp-p

! IC1200 ^ ^CAMERA REC/PB, LINE REC

74 nsec

2.8Vp-p

4-31

BASE BAND INPUTVC-208 (3/7)

4-32

4-33

4-34

DSR-PD100/PD100P

DSR-PD100/PD100P


4-35

4-36

4-37

MOTOR DRIVEVC-208 (4/7)

DSR-PD100/PD100P

SE-75 (YAW/PITCH SENSOR) PRINTED WIRING BOARD Ref. No. SE-75 Board; 10,000 Series SE-75 BOARDC450 C451 B-2 A-2

For schematic diagram Refer to page 4-17 for printed wiring board of VC-208.

CN450 A-2 L450 SE450 SE451 B-1 B-2 C-1

1-670-999For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.

12

There are few cases that the part printed on this diagram isnt mounted in this model.LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF) ED-48 (USER CONTROL) SE-75 (YAW/PITCH SENSOR)


VAP DRIVERVC-208 (5/7)

/ YAW/PITCH SENSORSE-75

4-39

4-40

4-41

4-42

DSR-PD100/PD100P


VC-208 BOARD (6/7)CAMERA REC/PB

! IC722 !

0.8Vp-p 2.3sec

4-43

4-44

4-45

4-46

CARD CONTROL, PWM CONTROLVC-208 (6/7)

DSR-PD100/PD100P


VC-208 BOARD (7/7)! IC751 &CAMERA REC/PB

6.85MHz

3.8Vp-p

HONEY, PCMCIA CONTROLVC-208 (7/7)

4-47

4-48

4-49

4-50

DSR-PD100/PD100P


VI-151 BOARD (1/10)1 IC1816 1, 2, 6, 7CAMERA REC

3.5Vp-p 6.8msec

2 IC1816 !, !CAMERA REC

2.0Vp-p 6.8msec

3 IC1816 @ PB

0.35Vp-p 6.8msec

4 IC1816 $CAMERA REC/PB

41.7MHz

2.3Vp-p

5 IC1816 $CAMERA REC

2.2Vp-p 25nsec

6 IC1814 ! PB

41.85MHz

2.0Vp-p

7 IC1814 ! @ PB

2.2Vp-p 25nsec

8 IC1814 #CAMERA REC/PB

2.6Vp-p 6.8msec

4-51

4-52

4-53

REC/PB AMPVI-151 (1/10)

DSR-PD100/PD100P

DSR-PD100/PD100P


VI-151 BOARD (2/10)CAMERA REC

9 IC1900 $

13.5MHz

3.2Vp-p

TIMING GENERATORVI-151 (2/10)

4-55

4-56

DSR-PD100/PD100P

DSR-PD100/PD100P


VI-151 BOARD (3/10)! Q1500 ECAMERA REC

0.22Vp-p H

! Q1500 E LINE REC(NTSC)

0.3Vp-p H

! Q1501 ECAMERA REC

0.2Vp-p H


0.3Vp-p H

! Q1502 ECAMERA REC

0.34Vp-p H


0.38Vp-p H

4-57

4-58

4-59

VIDEO INTERFACEVI-151 (3/10)

DSR-PD100/PD100P

DSR-PD100/PD100P


VI-151 BOARD (4/10)CAMERA REC/PB

! IC1600 ! (R1627)

24.58MHz

2.6Vp-p

DCT/IDCTVI-151 (4/10)

4-62

4-63

4-64

Ver 1.5 2003. 05

DSR-PD100/PD100P

DSR-PD100/PD100P


VI-151 BOARD (5/10)LINE OUT (I/O BLOCK)


0.4Vp-p H


0.26Vp-p H

! IC1402 7CAMERA REC/PB

H

2.0Vp-p

! IC1402 !CAMERA REC/PB

H

1.2Vp-p

@ IC1402 !CAMERA REC/PB

1.7Vp-p H

4-65

4-66

LINE OUTVI-151 (5/10)

4-67

DSR-PD100/PD100P


AUDIO PROCESSORVI-151 (6/10)

4-68

4-69

4-70

DSR-PD100/PD100P



@ IC2204 $ (R2300)

20.0MHz

3.0Vp-p

@ IC2204 %(X2201, R2262)

32.767kHz

3.0Vp-p

4-71

4-72

4-73

4-74

HI CONTROLVI-151 (7/10)

DSR-PD100/PD100P

DSR-PD100/PD100P



@ IC2401 1 (X2400)

20.0MHz

2.5Vp-p

4-76

MECHANISM CONTROLVI-151 (8/10)

4-77

4-78

DSR-PD100/PD100P

DSR-PD100/PD100P

For schematic diagram Refer to page 4-91 for printed wiring board. Refer to page 4-87 for FP-594 flexible board.


@ IC2503 4

# IC2503 ^

6.7msec

2.6Vp-p 1.1msec

2.8Vp-p

@ IC2503 @, @, @

# IC2503 ^

0.1Vp-p 1.1msec

1.1msec

900kHz

0.23Vp-p

@ IC2503 @, @, @

# IC2504 !

1.1msec

2.3Vp-p 0.92msec : DV 0.63msec : DVCAM

2.8Vp-p

@ IC2503 $

# IC2504 #, #, #

0.6Vp-p 0.56sec : DV 0.3sec : DVCAM 2.7Vp-p 80msec : DV 55msec : DVCAM

@ IC2503 $

2.7Vp-p

# IC2505 2, !, @

2.2Vp-p 0.76sec : DV 0.3 sec : DVCAM 1.1msec

@ IC2503 %

2.8Vp-p 3sec

4-79

4-80

4-81

DRUM/CAPSTAN MOTOR DRIVEVI-151 (9/10)

4-82

DSR-PD100/PD100P



# IC3200 %

4.7Vp-p 2.5sec

# IC3200 %

4.7Vp-p 2.5sec

# IC3200 ^

2.5sec

4.7Vp-p

DC/DC CONVERTERVI-151 (10/10)

4-83

4-84

4-85

4-86

DSR-PD100/PD100P

FP-594 (LOADING MOTOR, S/T REEL SENSOR) PRINTED WIRING BOARD Ref. No.: FP-594 Board; 9,000 Series

FP-594 BOARDM

M902 LOADING MOTOR

DEW SENSOR

S903 MODE SW

Q901 TAPE END

Q902 TAP E TOP

S901 C IN

S902 REC.P

CN901 MIC SW

CONTROL SWITCH BLOCK (FK-4880) is replaced as a block. So that there PRINTED WIRING BOARD are omitted.H901 S REEL SENSOR H902 T REEL SENSOR

For printed wiring boards Refer to page 4-82 for FP-594 board schematic diagram.

D901 TAPE LED

4-87

LOADING MOTOR, S/T REEL SENSORFP-594

4-88

4-89

USER CONTROLFK-4880

DSR-PD100/PD100PVI-151 BOARD (SIDE A)C1401 C1402 C1404 C1405 C1409 C1418 C1422 C1423 C1433 C1434 C1436 C1438 C1439 C1449 C1450 C1451 C1452 C1503 C1506 C1507 C1512 C1513 C1600 C1601 C1602 C1603 C1606 C1607 C1612 C1613 C1614 C1615 C1617 C1621 C1623 C1901 C1902 C1903 C1904 C1908 C1909 C1910 C1914 C1915 C1933 C2018 C2029 C2033 C2042 C2043 C2044 C2045 C2046 C2047 C2048 C2049 C2050 C2051 C2053 C2400 C2402 C2403 C2405 C2408 C2409 C2410 C2500 C2507 C2565 C2566 C2569 C2570 C2572 C2573 C2574 C2575 C2576 C2577 C2579 C2582 C2583 C2585 C2586 C2587 C2588 C2589 C3205 C3221 C3236 C3237 A-3 A-3 A-2 A-2 B-3 A-2 B-2 B-1 A-2 A-1 A-2 B-2 A-2 B-2 A-3 A-3 A-1 B-2 B-3 C-2 B-2 B-2 A-4 A-4 A-4 A-4 A-3 A-3 A-1 A-4 B-3 A-4 A-4 A-4 A-1 C-6 A-6 B-6 C-5 A-6 A-5 A-6 B-5 B-5 B-5 C-1 C-1 C-1 C-1 B-1 C-1 B-1 C-1 B-1 C-1 B-1 B-1 B-1 C-2 C-5 D-5 D-6 D-6 C-5 D-6 D-6 B-9 B-8 B-8 B-8 B-6 B-8 B-8 B-9 B-7 B-8 B-6 B-7 B-6 B-8 B-8 B-8 B-8 B-8 B-8 B-7 E-9 C-7 E-8 C-7 C3244 C3245 C3246 C3248 C3249 C3255 C3260 C3262 C3269 C3272 C3273 CN1810 CN2901 CN2903 CN2904 CN2905 CN2906 CN2911 CN2912 CN2913 CN3200 CN3201 D1600 D3204 D3205 D3208 D3213 D3216 D3217 D3225 D3226 D3227 IC1402 IC1501 IC1600 IC1601 IC1900 IC2002 IC2401 IC2404 IC2504 IC2505 L1400 L1500 L1501 L1601 L1602 L1603 L2400 L2512 L3200 L3201 L3202 L3203 L3204 L3205 L3206 L3207 L3208 L3209 L3214 L3215 L3216 L3217 C-7 E-7 E-7 E-8 E-8 E-9 D-7 D-7 D-7 C-9 B-9 A-5 C-2 A-1 D-9 F-6 F-8 A-6 A-8 A-7 B-9 C-9 A-4 C-8 C-8 E-7 E-7 E-8 E-8 C-7 C-7 C-7 A-2 B-3 A-3 B-4 B-6 C-2 C-6 C-4 B-8 B-7 A-2 C-2 B-2 A-4 A-1 A-4 C-5 B-7 D-9 E-9 E-7 D-9 D-8 D-8 E-8 D-7 E-8 D-8 E-8 E-8 E-8 E-8 Q3205 Q3206 Q3215 Q3216 Q3217 Q3219 Q3225 Q3226 Q3227 Q3231 Q3234 Q3235 Q3236 Q3238 Q3239 Q3240 Q3241 R1414 R1418 R1419 R1421 R1425 R1426 R1430 R1432 R1433 R1434 R1438 R1439 R1440 R1445 R1446 R1447 R1453 R1454 R1455 R1507 R1508 R1509 R1510 R1511 R1512 R1513 R1514 R1515 R1516 R1517 R1518 R1519 R1521 R1522 R1618 R1619 R1620 R1621 R1622 R1623 R1624 R1625 R1626 R1627 R1628 R1629 R1629 R1689 R1909 R1938 R1939 R1940 R1941 R1942 R1943 R1944 R1945 R1946 R2050 R2051 R2052 R2053 R2401 R2402 R2405 R2406 R2407 R2408 R2409 R2410 R2411 R2415 C-8 C-8 C-7 C-7 C-7 C-7 C-7 C-7 E-9 E-9 C-7 E-7 D-7 E-7 D-7 D-7 D-7 B-2 A-2 B-2 B-2 B-1 B-1 A-1 B-2 A-1 B-1 A-1 B-1 A-1 A-1 B-1 B-1 B-2 B-2 A-2 B-1 B-2 B-1 B-2 B-2 B-2 B-3 B-2 B-2 B-3 B-2 B-2 C-2 B-2 B-3 A-4 A-4 A-3 A-4 A-4 B-3 A-4 A-4 A-3 A-3 B-3 C-5 C-5 A-4 A-5 B-6 B-5 B-5 B-5 A-6 A-5 A-6 C-6 A-6 C-1 C-1 C-1 C-1 C-5 C-4 C-5 D-5 C-5 C-5 C-5 C-5 C-5 C-6 R2416 R2417 R2418 R2419 R2420 R2421 R2422 R2423 R2424 R2425 R2426 R2427 R2428 R2429 R2430 R2432 R2433 R2434 R2436 R2439 R2440 R2441 R2442 R2445 R2505 R2506 R2507 R2508 R2511 R2517 R2530 R2531 R2532 R2533 R2534 R2569 R2572 R2574 R2575 R2576 R2577 R2579 R2582 R2583 R2585 R2587 R2599 R2903 R2904 R2906 R2907 R3203 R3205 R3206 R3208 R3210 R3211 R3215 R3216 R3246 R3257 R3258 R3259 R3260 R3261 R3262 R3264 R3268 R3270 R3272 R3274 R3276 R3277 R3283 R3284 R3285 R3286 R3287 R3299 R3300 R3302 T3200 T3201 X1600 X2400 C-6 C-6 C-6 C-6 C-6 C-6 C-6 C-6 C-6 D-6 D-6 C-6 C-6 D-6 D-6 D-6 C-5 D-6 D-6 C-6 C-6 C-6 D-6 D-6 B-9 B-8 B-8 B-8 B-8 B-7 B-8 A-7 A-7 A-8 B-8 B-8 B-8 A-7 B-7 A-7 B-7 B-8 B-8 B-8 B-8 B-8 A-8 F-7 F-7 F-7 F-7 C-8 C-8 C-8 C-8 E-9 D-9 E-9 E-7 D-9 C-7 C-7 C-7 C-7 C-7 C-7 E-9 E-9 E-9 D-7 E-7 D-7 E-7 D-7 D-7 D-7 D-7 D-7 D-7 C-7 C-7 D-8 E-7 A-3 D-6

VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER) PRINTED WIRING BOARD Ref. No. VI-151 Board; 10,000 Series

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts TransistorC 65 4 3

Diode4 2

B

E

12 3

2

1

3

1

There are few cases that the part printed on this diagram isnt mounted in this model.XL-2 (MIC AMP) CD-202 (CCD IMAGER) DD-120 DC/DC CONVERTER

LF3200 C-8 PS3200 PS3201 PS3202 PS3203 PS3204 PS3205 PS3206 Q1402 Q1403 Q1405 Q1406 Q1500 Q1501 Q1502 Q1503 Q2507 Q3203 Q3204 C-9 C-9 C-9 C-9 C-9 C-9 C-9 A-1 A-1 B-1 A-2 B-1 B-2 B-2 B-2 B-8 C-8 C-8


VI-151 REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER

VIDEO IF, VIDEO I/O, SYSTEM/SERVO CONTROL, AUDIO, POWERVI-151

4-91

4-92

DSR-PD100/PD100P

VI-151 (REC/PB AMP, TIMING GENERATOR, VIDEO INTERFACE, DCT/IDCT, LINE OUT, AUDIO PROCESSOR, HI CONTROL, MECHANISM CONTROL, DRUM/CAPSTAN MOTOR DRIVE, DC/DC CONVERTER) PRINTED WIRING BOARD Ref. No. VI-151 Board; 10,000 Series

VI-151 BOARD (SIDE B)C1400 C1403 C1406 C1407 C1410 C1411 C1412 C1413 C1414 C1415 C1416 C1417 C1419 C1420 C1421 C1424 C1425 C1426 C1427 C1428 C1429 C1430 C1431 C1432 C1435 C1437 C1440 C1441 C1442 C1444 C1445 C1446 C1447 C1505 C1604 C1608 C1609 C1610 C1611 C1616 C1618 C1619 C1620 C1622 C1804 C1833 C1834 C1837 C1838 C1840 C1844 C1845 C1846 C1847 C1850 C1852 C1854 C1856 C1860 C1866 C1869 C1875 C1878 C1881 C1883 C1884 C1885 C1886 C1887 C1888 C1889 C1890 C1891 C2001 C2002 C2003 C2004 C2007 C2008 C2009 C2010 C2012 C2014 C2015 A-17 A-18 A-18 B-18 B-18 A-17 A-17 B-18 A-18 B-17 C-17 B-18 A-17 B-18 B-17 B-17 B-17 B-17 A-17 C-17 C-17 A-17 B-17 C-17 C-17 B-17 B-17 B-17 B-17 B-16 B-17 A-17 A-16 C-16 A-17 A-18 A-18 A-18 A-18 A-17 A-19 A-19 A-17 A-18 B-15 A-13 B-13 B-13 B-13 A-13 A-13 B-13 B-13 A-14 B-14 B-14 B-14 B-15 B-15 B-15 A-14 A-16 A-14 A-14 B-13 A-15 B-15 B-15 B-14 A-14 A-14 A-14 B-13 C-19 C-19 C-18 C-18 C-18 C-18 B-19 B-18 C-19 C-18 C-18 C2016 C2017 C2022 C2024 C2025 C2027 C2028 C2030 C2031 C2032 C2034 C2035 C2036 C2037 C2038 C2039 C2040 C2041 C2054 C2055 C2056 C2206 C2210 C2211 C2212 C2213 C2215 C2216 C2217 C2218 C2219 C2220 C2221 C2222 C2223 C2224 C2225 C2226 C2227 C2232 C2233 C2234 C2235 C2236 C2237 C2238 C2239 C2546 C2547 C2550 C2551 C2552 C2553 C2554 C2555 C2556 C2557 C2558 C2559 C2561 C2562 C2563 C2564 C2567 C2590 C2591 C3200 C3201 C3202 C3203 C3204 C3206 C3207 C3208 C3209 C3210 C3211 C3212 C3213 C3214 C3215 C3216 C3217 C3218 C-19 C-18 C-18 C-18 C-17 C-18 B-19 C-18 C-19 C-17 C-18 C-18 C-18 B-18 B-18 B-18 B-18 C-18 B-18 B-18 A-16 C-16 B-17 B-17 B-16 B-16 B-16 B-16 B-15 B-15 B-15 B-15 B-15 B-15 B-15 B-14 B-15 B-15 D-15 C-14 C-14 C-14 D-15 D-15 D-15 A-16 C-14 A-12 B-11 A-12 A-11 A-12 A-13 b-13 B-13 B-13 B-13 B-13 B-13 B-11 B-13 B-13 B-13 B-13 A-11 A-12 C-11 C-13 C-13 C-13 D-13 C-11 D-13 C-11 D-13 C-12 C-13 D-13 C-11 C-11 C-13 D-13 D-13 C-13 C3219 C3220 C3222 C3223 C3224 C3225 C3226 C3227 C3228 C3229 C3230 C3231 C3232 C3233 C3234 C3235 C3238 C3239 C3240 C3241 C3242 C3243 C3247 C3250 C3251 C3252 C3253 C3254 C3256 C3257 C3258 C3259 C3261 C3263 C3264 C3265 C3266 C3267 C3268 C3270 C3271 D-13 C-12 C-12 C-12 D-13 D-12 C-12 C-12 C-12 C-12 C-12 E-13 E-12 D-11 D-12 D-13 D-12 D-13 D-13 E-13 C-11 E-12 E-13 D-11 D-11 D-11 E-12 E-11 E-12 E-12 E-12 E-13 E-11 D-11 F-12 F-12 B-12 D-11 D-11 C-12 C-11 L1401 L1402 L1403 L1404 L1405 L1604 L1605 L1803 L1808 L1811 L2004 L2005 L2201 L2202 L2511 L3210 L3211 L3212 L3213 L3218 A-17 A-17 A-17 A-17 A-16 A-18 A-17 B-14 B-14 B-16 C-17 C-18 C-16 A-13 A-13 E-13 D-12 D-11 D-11 D-11 Q3247 Q3248 Q3249 Q3250 Q3251 Q3252 Q3253 Q3254 R1400 R1401 R1402 R1403 R1404 R1405 R1406 R1407 R1408 R1409 R1410 R1411 R1412 R1413 R1415 R1416 R1417 R1420 R1422 R1423 R1424 R1427 R1429 R1431 R1435 R1436 R1437 R1441 R1442 R1444 R1452 R1456 R1495 R1630 R1632 R1633 R1634 R1635 R1636 R1637 R1638 R1639 R1640 R1641 R1642 R1643 R1644 R1645 R1646 R1647 R1648 R1649 R1650 R1651 R1652 R1653 R1654 R1694 R1695 R1696 R1697 R1698 R1699 R1826 R1828 R1834 R1836 R1837 R1838 R1843 R1846 R1848 R1852 R1853 R1855 E-12 D-11 E-13 D-11 F-11 C-12 E-11 B-13 A-18 A-18 A-18 A-18 C-17 C-17 A-17 B-18 A-17 C-17 A-18 C-17 A-17 C-17 B-16 B-18 C-17 B-17 B-17 B-17 B-17 B-17 B-17 B-17 B-17 B-17 B-17 A-17 A-16 B-17 A-16 B-16 A-17 B-18 A-18 A-19 A-18 A-18 B-19 B-19 B-19 B-19 A-19 A-19 A-18 A-18 A-18 A-18 A-18 A-18 A-18 A-18 A-18 A-18 A-18 A-19 B-19 A-19 A-19 A-19 A-19 A-19 B-19 B-14 B-14 B-15 B-15 A-15 A-15 A-15 A-15 A-15 B-15 A-15 A-15 R1857 R1859 R1869 R1870 R1871 R1872 R1874 R1875 R1876 R1877 R1878 R1879 R2017 R2018 R2019 R2021 R2022 R2023 R2028 R2029 R2031 R2032 R2038 R2039 R2040 R2041 R2054 R2055 R2056 R2057 R2058 R2059 R2060 R2061 R2062 R2063 R2064 R2065 R2066 R2201 R2202 R2203 R2204 R2205 R2206 R2207 R2208 R2209 R2210 R2211 R2212 R2213 R2214 R2215 R2221 R2222 R2223 R2224 R2225 R2226 R2227 R2229 R2230 R2231 R2232 R2233 R2234 R2235 R2236 R2237 R2238 R2239 R2240 R2241 R2242 R2243 R2244 R2245 R2246 R2247 R2248 R2249 R2250 R2251 A-15 A-15 B-14 B-14 A-14 B-13 A-13 B-13 B-13 B-15 A-15 B-14 B-19 B-19 C-17 B-19 B-19 C-17 C-19 C-19 C-19 C-19 C-19 C-19 C-17 C-17 C-17 C-17 B-19 B-19 B-19 B-19 B-19 B-19 B-18 B-18 C-18 C-17 C-17 B-16 B-16 B-16 B-16 D-14 D-14 B-16 B-16 B-16 D-14 B-16 C-16 C-14 D-14 C-16 C-16 C-16 C-16 C-16 C-16 C-16 C-16 C-16 C-15 C-16 C-16 B-16 D-15 C-16 B-15 B-15 B-15 B-15 D-15 D-15 D-15 D-14 D-14 D-15 B-16 C-15 B-15 B-15 B-15 B-15 R2252 R2253 R2254 R2255 R2257 R2258 R2259 R2260 R2261 R2262 R2263 R2264 R2265 R2266 R2267 R2268 R2269 R2270 R2271 R2272 R2273 R2274 R2275 R2276 R2277 R2278 R2279 R2280 R2281 R2282 R2283 R2284 R2285 R2286 R2287 R2288 R2289 R2290 R2291 R2292 R2293 R2294 R2295 R2296 R2297 R2298 R2299 R2300 R2301 R2302 R2303 R2304 R2509 R2510 R2512 R2546 R2547 R2549 R2550 R2551 R2552 R2553 R2554 R2556 R2557 R2558 R2559 R2560 R2561 R2562 R2563 R2564 R2565 R2566 R2567 R2568 R2570 R2571 R2573 R2578 R2580 R2581 R2586 R2901 B-15 B-14 B-15 B-15 D-15 B-14 B-14 C-14 D-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 C-14 D-15 C-15 C-15 C-15 C-15 C-15 C-15 C-15 C-16 C-15 B-15 B-15 B-15 B-15 B-15 B-15 B-15 B-14 B-14 C-14 C-14 C-14 C-14 C-14 D-15 A-16 A-16 A-16 A-16 B-13 B-13 B-12 B-13 B-13 A-11 A-12 A-13 B-13 B-13 B-13 B-11 B-11 B-13 B-11 B-11 A-12 A-12 A-12 B-11 B-11 B-13 B-13 B-13 A-13 A-13 A-11 A-11 A-11 A-12 A-11 F-12 R2902 R2905 R3200 R3201 R3202 R3204 R3207 R3209 R3212 R3213 R3214 R3217 R3218 R3219 R3220 R3221 R3222 R3223 R3224 R3225 R3226 R3227 R3228 R3229 R3230 R3231 R3232 R3233 R3234 R3235 R3236 R3237 R3238 R3239 R3240 R3241 R3242 R3243 R3244 R3245 R3247 R3248 R3249 R3250 R3251 R3252 R3253 R3254 R3255 R3256 R3263 R3265 R3266 R3267 R3269 R3271 R3273 R3275 R3278 R3279 R3280 R3281 R3282 R3288 R3289 R3290 R3291 R3292 R3293 R3294 R3295 R3296 R3297 R3298 R3301 R3303 X2200 X2201 E-12 C-11 C-11 C-11 C-12 C-13 B-13 B-13 B-12 C-12 C-12 C-12 D-13 B-12 B-13 C-13 D-13 D-13 C-13 D-13 D-13 E-11 D-11 E-11 D-13 D-13 D-13 D-13 D-13 D-13 C-13 D-13 D-13 D-13 D-13 D-13 D-13 D-13 D-13 D-13 C-13 C-12 C-12 C-13 C-13 C-12 C-12 B-13 C-12 C-12 F-12 E-12 E-12 E-11 E-11 E-13 E-13 B-13 E-13 E-13 E-13 E-11 E-11 E-12 E-12 E-13 D-11 D-11 E-12 E-13 E-12 F-12 F-12 F-11 E-12 B-11 D-15 D-14

PS2200 D-14 Q1400 Q1404 Q1407 Q1810 Q2003 Q2004 Q2005 Q2006 Q2007 Q2008 Q2009 Q2011 Q2012 Q2013 Q2014 Q2200 Q2201 Q2202 Q2203 Q2206 Q2211 Q2212 Q2213 Q2214 Q2216 Q2217 Q2218 Q2219 Q2220 Q2221 Q2505 Q2506 Q2901 Q3200 Q3201 Q3202 Q3207 Q3208 Q3209 Q3210 Q3211 Q3212 Q3213 Q3214 Q3218 Q3220 Q3221 Q3222 Q3223 Q3224 Q3228 Q3229 Q3230 Q3232 Q3233 Q3237 Q3242 Q3243 Q3244 Q3245 Q3246 A-18 A-16 B-16 B-13 C-17 C-17 C-17 B-19 B-19 B-19 B-19 C-17 C-17 C-17 C-17 B-16 B-16 A-16 B-16 D-14 B-17 C-16 C-14 B-14 C-14 C-16 C-16 C-17 A-16 A-16 A-11 A-11 B-14 C-12 C-11 C-11 C-12 E-13 E-12 D-12 D-12 D-13 E-12 D-12 E-12 D-12 D-12 D-13 E-13 D-12 E-11 E-12 E-11 E-13 E-13 E-13 E-11 E-11 E-12 E-12 E-12

CN2902 C-19 CN2907 F-13 D2200 D2201 D2203 D2206 D2207 D2208 D2500 D3200 D3201 D3202 D3203 D3206 D3207 D3209 D3210 D3211 D3212 D3214 D3215 D3220 D3221 D3223 D3224 IC1400 IC1401 IC1403 IC1502 IC1602 IC1814 IC1816 IC2001 IC2200 IC2201 IC2203 IC2204 IC2503 IC3200 D-14 D-14 D-14 C-16 B-14 D-15 A-11 B-11 B-11 B-11 B-11 C-12 C-12 E-12 D-13 E-12 D-12 D-12 D-12 C-12 C-12 B-13 C-13 A-17 A-16 B-17 C-16 B-19 A-13 B-15 C-18 D-15 C-16 B-16 C-15 B-12 C-13

4-93

4-94

VIDEO IF, VIDEO I/O & IR, SYSTEM/SERVO CONTROL, AUDIO, POWERVI-151

DSR-PD100/PD100P

FP-21 (FOCUS SW) FLEXIBLE BOARDFP-21 FLEXIBLE BOARDPH701

MA-333 (STEREO MIC AMP) PRINTED WIRING BOARD Ref. No. MA-333 Board; 10,000 Series MA-333 BOARDC7300 C7301 C7302 C7305 C7306 C7307 C7308 C7309 C7310 C7312 C7313 C7314 C7315 C7316 C7317 C7318 C7319 C7320 C7321 C7322 C7323 C7324 C7325 C7326 C7327 C7328 C7329 C7330 C7331 C7332 C7333 C7336 C7337 C7338 C7339 C7340 C7341 C7342 C7343 C7344 C7345 C7346 C7347 A-1 D-3 A-2 A-2 A-2 A-3 A-2 A-3 A-2 A-3 A-2 A-3 A-2 A-3 A-1 A-2 A-3 A-3 A-1 B-1 B-1 A-1 B-3 B-3 D-1 B-2 B-1 B-1 B-3 B-3 B-3 B-3 B-3 B-2 B-3 B-2 B-3 B-3 B-2 C-1 C-3 C-3 B-3 C7348 C7350 C7351 C7352 C7353 C7354 C7355 C7356 C7357 CN7300 CN7301 CN7302 CN7303 CN7304 CN7305 D7300 D7304 D7305 FB730 FB731 B-2 B-2 D-2 D-3 D-2 D-3 D-2 C-3 D-3 E-1 E-3 E-2 E-3 D-1 D-1 A-1 E-2 E-2 A-3 A-3 R7313 R7314 R7315 R7316 R7317 R7318 R7319 R7320 R7321 R7322 R7323 R7324 R7326 R7327 R7328 R7329 R7331 R7332 R7335 R7337 R7339 R7342 R7343 R7344 R7345 R7346 R7347 R7348 R7350 R7351 R7352 R7353 R7354 R7355 R7356 R7357 R7358 R7359 R7360 R7361 R7362 R7363 A-1 A-3 A-1 A-3 A-1 B-3 B-2 B-1 B-2 B-3 C-1 B-1 B-3 B-3 B-1 D-1 B-3 B-3 B-1 B-1 B-1 B-2 B-2 B-2 C-2 B-2 B-2 B-2 D-2 D-3 D-3 D-2 D-3 D-2 D-3 D-3 D-2 D-3 D-2 E-2 E-1 D-3

RI-10 (SIRCS RECEIVER) PRINTED WIRING BOARD Ref. No. RI-10 Board; 10,000 Series RI-10 BOARDCN7401 A-3 D7401 D7402 D7403 A-3 B-1 B-2

IC7401 B-3

PH700

2

8

FP-21

S701 PUSH AUTO 1-670-988-

S700 FOCUS INFINITY - MANUAL - AUTO 11

S702 ND FILTER

1

10

IC7301 B-2 IC7302 D-2 IC7303 D-2 Q7300 Q7301 Q7302 Q7303 Q7304 R7302 R7303 R7304 R7305 R7306 R7309 R7310 R7311 R7312 D-1 B-1 B-1 B-1 D-3 A-3 A-1 A-1 E-2 E-2 A-2 A-2 E-2 E-2

FP-22 (MIC JACK) FLEXIBLE BOARD

FP-22 FLEXIBLE BOARD1-670-989J7301 MIC (PLAG IN POWER)

STEREO MIC AMPMA-333

5

8 1 FP-22

1

11

FP-20 FP-10 ED-48 LENS BLOCK

LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF) (USER CONTROL) SE-75 (YAW/PITCH SENSOR)

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts Transistor Diode3

FP-21 (FOCUS) FP-9

C

(From CAPSTAN MOTOR) From LOADING MOTOR, S/T REEL SENSOR (From DRUM MOTOR) FP-22 (MIC JACK) FP-12 FP-37 FP-14 (From VIDEO HEAD)


B

E

2

1


/ SIRCS RECEIVERRI-10

4-96

4-97

4-98

DSR-PD100/PD100P

DSR-PD100/PD100P

4-99

4-100

4-101

STEREO MIC AMPMA-333

/ SIRCS RECEIVERRI-10

DSR-PD100/PD100P

FP-16 (PANEL SWITCH) FLEXIBLE BOARD

FP-16 FLEXIBLE BOARDS002 (PANEL CLOSE) S001 (PANEL REV)

FP-16

1-670-983-

8

1

11

6

1

FP-18 (USER CONTROL) FLEXIBLE BOARDFP-18 FLEXIBLE BOARD

FP-17 FP-23 (S-Y/C IN/OUT)

FP-16 FP-11 FP-13 FP-8

USER CONTROLCK-80, ED-48, FP-16, FP-18

mk 0

1-670-985-

FP-18

FK-4880 (USER CONTROL)


For LED


4-103

4-104

4-105

4-106

DSR-PD100/PD100P

CK-80 (USER CONTROL) PRINTED WIRING BOARD Ref. No. CK-80 Board; 10,000 Series CK-80 BOARDBT7200 C7200 C7200 CN7200 CN7201 CN7202 CN7203 CN7204 CN7205 CN7207 CN7208 CN7209 CN7210 D7200 D7201 D7202 D7203 D7204 D7206 D7207 D7208 D7209 D7211 D7212 D7214 D7215 IC7200 Q7200 Q7201 R7200 R7201 R7202 R7203 R7204 R7205 R7206 R7207 R7208 R7209 R7210 R7211 R7212 C-10 E-10 E-10 A-8 A-10 D-9 F-10 F-14 A-3 F-8 C-9 C-7 D-17 C-13 D-16 F-10 A-10 E-15 D-16 C-13 E-11 E-11 C-16 C-16 D-16 D-16 E-10 E-11 E-11 D-16 E-10 C-14 D-14 E-11 D-16 E-11 E-10 E-10 E-10 E-15 C-13 D-13 R7213 R7214 R7215 R7216 R7217 R7218 R7219 R7220 R7221 R7222 R7223 R7224 R7225 R7226 R7227 R7228 R7229 R7230 R7231 R7232 R7233 R7234 R7235 R7236 S7200 S7201 S7202 S7203 S7204 S7205 S7206 S7207 S7208 S7209 S7210 S7211 S7212 S7213 S7214 S7219 E-11 E-10 D-13 C-13 D-12 B-16 D-14 D-15 B-16 E-12 B-16 D-12 C-12 F-10 F-10 D-16 E-16 E-16 E-16 E-16 D-16 F-9 F-9 E-13 E-16 C-14 D-14 E-15 C-13 D-13 E-13 D-15 D-12 E-14 B-16 E-12 C-12 A-11 E-17 B-17

ED-48 (USER CONTROL) PRINTED WIRING BOARD Ref. No. ED-48 Board; 10,000 Series

12

ED-48 BOARDCN7000 A-2 D7000 D7001 R7000 R7001 R7002 R7003 R7004 S7000 S7001 S7002 S7003 A-1 A-1 A-2 B-2 B-2 B-2 B-2 A-3 A-4 B-4 B-3

12

LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF) ED-48 (USER CONTROL)

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram.

SE-75 (YAW/PITCH SENSOR)



4-107

4-108

4-109

4-110

USER CONTROLCK-80, ED-48

DSR-PD100/PD100P

FP-23 (S VIDEO) FLEXIBLE BOARDFP-23 FLEXIBLE BOARDINTELLIGENT ACCESSORY SHOE1 8

JK-163 (AUDIO/VIDEO IN/OUT) PRINTED WIRING BOARD Ref. No. JK-163 Board; 10,000 Series JK-163 BOARDC7100 C7101 C7102 C7103 C7104 C-4 D-4 C-5 D-4 C-1 FB715 FB716 FB717 FB718 J7100 J7101 J7102 L7100 L7101 L7102 L7103 L7104 R7102 VDR711 VDR714 VDR715 VDR717 VDR718 C-5 C-1 C-1 C-1 C-2 C-2 D-2 C-4 C-5 C-5 D-4 C-1 C-4 C-4 C-5 B-5 D-4 C-5

1 - 670 - 990 -

FP - 23

8

1

CN7100 B-2 CN7101 C-1 CN7102 B-5 D7100 D7102 D7103 D7104 D7105 D7106 FB710 FB711 FB712 FB713 FB714 B-4 B-1 C-5 D-5 C-5 C-5 B-4 C-4 B-1 D-1 C-1

C

Y J100 S VIDEO

1

14

11

For printed wiring boards This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. Chip parts Diode3

12

2

1

There are few cases that the part printed on this diagram isnt mounted in this model.FK-4880 (USER CONTROL) FP-17 FP-23 (S-Y/C IN/OUT)

LB-55 (EVF BACK-LIGHT) VF-121 (COLOR EVF) ED-48 (USER CONTROL) SE-75 (YAW/PITCH SENSOR)


For LED FP-16 FP-11 FP-13 FP-8

JK-163 (AUDIO/VIDEO IN/OUT) RI-10 (SIRCS RECEIVER)FP-19 (USER CONTROL)

CK-80 MA-333 USER CONTORL, (STEREO MIC AMP) LCD DRIVE PD-101 (RGB DRIVER, TIMING GENERATOR, BACK-LIGHT)

S-Y/C IN/OUTFP-23

/ AUDIO/VIDEO IN/OUTJK-163

4-111

4-112

4-113

4-114

DSR-PD100/PD100P

For schematic diagram Refer to page 4-121 for PD-101 printed wiring board. Refer to page 4-121 for FP-19 flexible board.

PD-101 BOARD (1/2)CAMERA REC/PB

1 IC5502 8

H

0.3Vp-p

2 IC5502 9

H

0.2Vp-p

3 IC5502 !

0.22Vp-p H

4 IC5502 @

2H

4.2Vp-p

5 IC5502 @4.2Vp-p

2H

6 IC5502 @4.2Vp-p

2H

7 IC5502 $

1.4Vp-p 2H

4-115

Date post:	14-Dec-2014
Category:	Documents
Upload:	marcel-murcia
View:	204 times
Download:	35 times

SONY DSR-PD100, PD100P SERVICE MANUAL VER 1.5 2003.05 (9-974-114-16)

Documents