LEISURE TIME ®
Spa Minerals
Sold By:Leisure Time Chemical Corp.,An Arch Chemicals, Inc. business1400 Bluegrass Lakes Pkwy.Alpharetta, GA 30004 USA
For more information regarding this or other Leisure Time® products, visit our website at LeisureTimeSpa.com
PART NO. 06532453 ITEM NO. 23434A23434A-A-0914
Sold By:Leisure Time Chemical Corp.,An Arch Chemicals, Inc. business1400 Bluegrass Lakes Pkwy.Alpharetta, GA 30004 USA
For more information regarding this or other Leisure Time® products, visit our website at LeisureTimeSpa.com
PART NO. 06532453 ITEM NO. 23434A23434A-A-0914
Manufactured for Leisure Time® by King Technology, Hopkins,MN 55343
Patents: www.KingTechnology.com/IP
Leisure Time® and the Leisure Time® water drop logo are registered trademarks of Arch Chemicals, Inc.
Manufactured for Leisure Time® by King Technology, Hopkins,MN 55343
Patents: www.KingTechnology.com/IP
Leisure Time® and the Leisure Time® water drop logo are registered trademarks of Arch Chemicals, Inc.
E071114553051443R3A 20-44-2293
Leisure Time® Spa Minerals contain a patented mineral formula that destroys bacteria while neutralizing acids, which helps keep the pH in an acceptable range with less monitoring. Using the Leisure Time® Spa Mineral System+ with reduced levels of bromine or chlorine improves spa pleasure by reducing the problems associated with bromine or chlorine including faded bathing suits, premature damage to spa equipment or surfaces and smelly odors.Replace Leisure Time® Spa Minerals after 4 months or when draining and refilling spa with fresh water.
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.
Directions for Use: For use in spas up to 600 gallons. Ensure all spa equipment is working properly. Operate the pump and filter for at least 3 hours per day. Clean filter following manufacturer’s directions. Adjust pH to between 7.2 - 7.8. With a freshly filled spa, establish a bromine or chlorine residual of 1.0-2.0 ppm with an EPA approved spa shock or by other means. Always maintain a bromine or chlorine residual of at least 1.0 ppm. Shock spa once a week or as needed. When using other products as outlined in directions for this product, always follow directions on those products. Keep the spa free of leaves and debris.
Installing Leisure Time® Spa Minerals: Place Leisure Time® Spa Minerals in one of the following locations:a. Majority of Spas: insert Leisure Time® Spa Minerals inside filter cartridge core. Do not allow product to sit too low in the filter. If blocking water flow, install in filter well. If installed inside a standpipe, attach a string to the handle on top for easy removal.b. High Flow Spas: on skimmer filters with 2.5 HP or larger pump motors, place Leisure Time® Spa Minerals in filter well outside the filter cartridge.c. Small Cartridge or Other Spas: place Leisure Time® Spa Minerals in skimmer tray.
Disposal: After four months of use, or when draining and refilling the spa with fresh water, discard Leisure Time® Spa Minerals in trash even if, upon shaking, it appears there is spent media left inside. Once wetted the time released minerals in the cartridge are effective up to four months. Non-refillable container. Do not reuse or refill this container. Do not attempt to reuse the product once removed from the spa.
NOTE: Buyer assumes all responsibility for safety and use not in accordance with directions.
EASY INSTALLATION.
NO ASSEMBLYREQUIRED.
Leisure Time® Spa Minerals works together with very low levels of bromine or chlorine to control bacteria, condition the water and help neutralize pH.
Now easier to Install
• Insert Leisure Time® Spa Minerals into filter cartridge, in filter well or in skimmer
• Lower your bromine or chlorine levels to as low as 1.0 ppm*
• Replace Leisure Time® Spa Minerals every 4 months or when draining and refilling spa
FROG® OffersMore Relaxation
• Simply a more enjoyable spa experience
• Permanent rod fits almost all spas
• Welded rod helps prevent breakage
• Inserts easily into filter
• Also works in most skimmers or filter wells
• Water feels softer with a crystal clear shine
• Lasts 4 full months
Up to 50%* reduction in bromine or chlorine useUp to 50%* reduction in bromine or chlorine use
The Leisure Time® Spa Mineral System+ Improves Water Quality By:• Destroying bacteria for improved clarity• Helping to maintain a neutral pH• Reducing bromine or chlorine use for
softer water* Compared to the minimum ANSI
recommended bromine or chlorine level of 2.0 ppm for a spa
KEEP OUT OF REACH OF CHILDREN
CAUTIONActive Ingredient:
Silver Chloride ................................. 0.5%Other Ingredients: ............................. 99.5%Total: .............................................. 100.00%
Net Wt. 58 grams (2.05 oz)
EPA REG. NO. 53735-11-41760EPA EST. NO. 071209-AZ-001
KEEP OUT OF REACH OF CHILDREN
CAUTIONActive Ingredient:
Silver Chloride ................................. 0.5%Other Ingredients: ............................. 99.5%Total: .............................................. 100.00%
Net Wt. 58 grams (2.05 oz)
EPA REG. NO. 53735-11-41760EPA EST. NO. 071209-AZ-001
Contents: 1 Leisure Time® Spa Minerals No Assembly RequiredContents: 1 Leisure Time® Spa Minerals No Assembly Required
LEISURE TIME®
Spa Minerals
LASTS 4 FULL MONTHS
IN CASE OF EMERGENCY CALL 1-800-654-6911
Mineral Spa Care developed with technology from FROG®Mineral Spa Care developed with technology from FROG®
+ The Leisure Time® Spa Minerals System consists of the FROG® minerals silver chloride and carbonate used with 1.0 ppm bromine or chlorine. Leisure
Time® Spa Minerals must be used in conjunction with an EPA registered bromine or chlorine spa product or a bromine or chlorine delivery device.
+ The Leisure Time® Spa Minerals System consists of the FROG® minerals silver chloride and carbonate used with 1.0 ppm bromine or chlorine. Leisure
Time® Spa Minerals must be used in conjunction with an EPA registered bromine or chlorine spa product or a bromine or chlorine delivery device.
PENDING
Product Description:
Leisure Time® Spa Minerals contains a patented mineral formula that destroys bacteria while neutral-izing acids, which helps keep the pH in an acceptable range with less monitor-ing. Using the Leisure Time Spa Mineral System+ with reduced levels of bromine or chlorine improves spa pleasure by reduc-ing the problems associated with bromine or chlorine including faded bathing suits, premature damage to spa equipment or surfaces and smelly odors.
Leisure Time® Spa Minerals Patented Mineral Spa Disinfectant
Operation Manual For Use in the Filter Core
• Up to 50%* reduction in bromine or chlorine use.
The Leisure Time® Spa Mineral System+ Improves Water Quality by:
• Destroying bacteria for improved clarity• Helping to maintain a neutral pH
• Reducing bromine or chlorine use for softer water+ Leisure Time® Spa Mineral System consists of the FROG® minerals silver chloride
and carbonate used with 1.0 ppm bromine or chlorine. Leisure Time® Spa Minerals must be used in conjunction with an EPA registered bromine
or chlorine spa product or a bromine or chlorine delivery device.
Regular Spa Care
• Ensure all spa equipment is working properly.
• Run filtration system a mini-mum of three hours per day.
• Regularly test water for pH, total alkalinity and bromine or chlorine levels.
• Maintain at least a 1.0 ppm bromine or chlorine level at all times.
• Shock the spa once a week or as needed. Additional shocking may be required if the spa is under heavy use. This is often the case when the spa is new.
• Leisure Time Spa Minerals must be replaced every 4 months. After four months of use or when draining and refilling the spa with fresh water, discard Leisure Time Spa Minerals
in trash even if, upon shaking, it appears there is spent media left inside. Once wetted the time released minerals in the cartridge are effective up to four months. Non-refillable container. Do not reuse or refill this product. Do not attempt to reuse the product once removed from the spa.
Active Ingredient: Silver Chloride . . . . 0.5%Other Ingredients: . . . . 99.5%Total: . . . . . . . . . . . . . 100.0%
*Compared to the minimum ANSI recommended bromine or chlorine level of 2.0 ppm for a spa.
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.Replace Leisure Time Spa Minerals after 4 months or when draining and refilling spa with fresh water.
Leisure Time® Alpharetta, Georgia 30004For more information regarding this or other Leisure Time products, visit our website at LeisureTimeSpa.com
Patents: www.KingTechnology.com/IPE071114553091443R5N Item No: 23434 23434-A-0812 20-48-0141
Net Wt.: 58 gramsEPA Reg. No.: 53735-11-41760EPA Est. No.: 071209-AZ-001
KEEP OUT OF REACH OF CHILDRENCAUTION
Descripción del producto: Los Minerales Leisure Time® para Spas contienen una fórmula mineral patentada que destruye las bacterias al tiempo que neutraliza los ácidos, lo que ayuda a mantener el pH en un nivel seguro con menos control. El uso de el Sistema+ Minerale Leisure Time para Spas con niveles reducidos de bromo o cloro mejora el placer de estar en un spa reduc-iendo un aceptable relacionadas con el bromo o el cloro incluyendo la decoloración de los trajes de baño, los daños en el equipo o en las superficies del spa antes de tiempo y los malos olores. Cambie el envase de los Minerales Leisure Time para Spas después de 4 meses o cuando vacíe y vuelva a llenar el spa con agua nueva.
Minerales Leisure Time® para SpasManual de uso
Para colocar en el centro del filtroDesinfectante mineral para spas patentado
• Hasta 50%* reducción en el uso de bromo o cloro.
El Leisure Time® Sistema Mineral+ Mejora La Calidad del Agua:
• Destruyendo las bacterias para lograr una mayor claridad• Ayudando a mantener un pH neutro
• Reduciendo el uso de bromo o cloro para obtener un agua más suave
Cuidado habitual del spa
• Asegúrese de que todos los equipos del spa fun-cionen correctamente.
• Haga funcionar el sistema de filtrado tres horas por día como mínimo.
• Controle con regularidad los niveles de pH, alcalinidad total y bromo o cloro del agua.
• Mantenga siempre un nivel de bromo o cloro de por lo menos 1,0 ppm.
• Hágale un tratamiento de choque al spa una vez a la semana o como fuera necesario. Se puede requerir un tratamiento de choque adicional si el spa se usa mucho. Por lo general, esto sucede cuando el spa es nuevo.• Debe cambiar los Minerales Leisure Time para Spas cada 4 meses. Después de cuatro meses de uso o
cuando vacíe y vuelva a llenar el spa con agua nueva, deseche los Minerales Leisure Time para Spas aún cuando, después de agitar el envase, pareciera que todavía hay sustancias en el interi-or. Una vez que se mojan los minerales
de liberación gradual del cartucho, éstos tienen efecto hasta cuatro meses. Contenedor que no se puede rel-lenar. No vuelva a emplear ni rellene este producto. No intente volver a usar el producto una vez que lo saque del spa. Ingrediente activo:
Cloruro de plata . . . . 0,5%Otros ingredientes: . . . 99,5%Total: . . . . . . . . . . . . . 100,0%
*Comparado con el nivel mínimo de bromo o cloro recomendado por el ANSI (Instituto Nacional Estadounidense de Estándares, ANSI, por sus siglas en inglés) de 2,0 ppm para un spa.
Usar este producto de manera que no concuerde con lo establecido en su etiqueta es una violación a la ley federal.
Leisure Time® Alpharetta, Georgia 30004 Para más información acerca de este u otros productos Leisure Times, visite nuestro sitio web en LeisureTimeSpa.com
Patentes: www.KingTechnology.com/IPE071114553091443R5N Item No: 23434 23434-A-0812 20-48-0141
Peso neto: 58 gramosNúmero de registro EPA: 53735-11-41760Número de establecimiento EPA: 071209-AZ-001
MANTENER FUERA DEL ALCANCE DE LOS NIÑOSPRECAUCION
Prográmelo para 4 meses
Desarrollado con tecnología:
Developed with technology from: ®
®
+ Leisure Time® Mineral System consiste en los minerales FROG® cloruro de plata y carbonato, utilizados con 1.0 ppm de bromo o cloro. Leisure Time® debe usarse con un producto de bromo o cloro para spa registrado ante la EPA, o con un dispositivo de suministro de bromo o cloro.
Installing Leisure Time® Spa Minerals
• Place Leisure Time Spa Minerals in one of the following locations in spa:
a) Majority of Spas - Insert Leisure Time Spa Minerals inside filter cartridge core (Diagram A).Do not allow Leisure Time Spa Minerals to sit too low in the filter. If blocking water flow, install in filter well (Diagram B). If Leisure Time Spa Minerals is inside a standpipe, attach a string to the FROG® head handle for easy removal.
b) High Flow Spas - On skimmer filters with 2.5 HP or larger pump motors, place Leisure Time Spa Minerals in filter well outside the filter cartridge (Diagram B).
c) Small Cartridge or Other Spas - Place Leisure Time Spa Minerals in skimmer tray (Diagram C).
Diagram A Diagram CDiagram B High Flow Spas In Filter Well
Vertical
I
Horizontal
I–STANDPIPE
Specifications• Fits in most filters.• Handles spas up to 600 gallons.• Lasts 4 months.• Use with bromine or chlorine.
Spa Start Up• Always drain and refill spa at least every 4 months.• Clean or replace filter cartridge when dirty (Follow manufacturer's directions).• Balance water according to the chart.• Shock spa to establish a bromine or chlorine residual of 1.0-2.0 ppm with an EPA approved spa shock or by other means. (Follow manufacturer's directions.)• Begin Regular Spa Care procedures on back page. *NOTE: Bromine or chlorine levels are lower only when used with Leisure Time Spa Mineral System+.
Water Balance GuidelinespH: 7.2–7.8Total Alkalinity: 80–180 ppmCalcium Hardness: 150–400Total Dissolved Solids: <1500Free Chlorine (or Bromine) 1.0–2.0 ppm
If unit is too tall, cut rod at hash marks to shorten.
Instalación del desinfectante para el cuidado mineral del spa Leisure Time® Spa Minerals
• Ubique los Minerales Leisure Time para Spas en uno de los siguientes lugares del spa:
Gráfico Aa) En la mayoría de los spas – Coloque el Leisure Time Spa Minerals en el centro del cartucho del filtro (Gráfico A).No deje que el Leisure Time Spa Minerals caiga demasiado dentro del filtro. Siobstaculiza el flujo de agua, instálelo en el hueco del filtro
(Gráfico B). Si el Leisure Time Spa Minerals™ está en una columna de alimentación, ate un cordón en la manivela superior del FROG® para retirarlo fácilmente.
Gráfico Cc) Spas de cartucho pequeño u otros – Coloque el Leisure Time Spa Minerals en la bandeja del skimmer
Gráfico B Spas de alto flujo en el hueco del filtrob) Spas de alto flujo – En los filtros del skimmer de 2,5 HP o motobom-bas más grandes, ubique el Leisure Time Spa Minerals en el hueco del filtro fuera del cartucho del filtro
Vertical
Horizontal
I–COLUMNA DE ALIMENTACIÓN
Especificaciones• Se ajusta a la mayoría de los filtros.• Responde a un spa de hasta 600 galones (2271 litros).• Dura 4 meses.• Se usa con bromo o cloro.
Puesta en marcha del spa • Siempre vacíe y vuelva a llenar el spa por lo menos cada 4 meses.• Limpie o cambie el cartucho del filtro cuando se ensu-cie. (Siga las instrucciones del fabricante).• Equilibre el agua de acuerdo a la tabla.• Hágale un trata-miento de choque al spa para establecer un residual de bromo o cloro de 1,0-2,0 ppm con un tratamiento de choque aprobado por la EPA (Agencia de Protección Ambiental, EPA, por sus siglas en inglós) o por otros medios. (Siga las instrucciones del fabricante).
Pautas Para el eQuiliBriO del aGuapH: 7,2–7,8Alcalinidad Total: 80–180 ppmDureza del calcio: 150–400Total de sólidos disueltos: <1500Cloro o (bromo) libre 1,0–2,0 ppm
Si la unidad es demasiado alta, corte la varilla en las marcas para acortarla.
• Comience con los procedimientos para el cuidado habitual del spa que aparecen en la contraportada. *NOTA: los niveles de bromo o cloro son menores solo cuando se utilizan con los Leisure Time Sistema Mineral+.
bandeja del skimmer
skimmer tray