Version 1.0
ipLDK-60
Quick Installation GuideSimple integrated version of manuals for installation and programming
Step 1 – Hardware InstallationStep 2 – Basic Programming
Always Surpassing Customers Expectations2 LG-Nortel Confidential Information
ContentsGetting Started
Overview1.Overall Installation Procedure2.Understanding ipLDK-60 Hardware
Step 1) Hardware Installation1.Installing the Hardware
Step 2) Basic Programming2-1) Initializing hardware configuration automatically2-2) Installing PC-Admin Program and connecting PC to the system2-3) Describing the basic menu trees of PC-ADMIN Program 2-4) Setting the nation code as “Brazil”2-5) Understanding the default configuration2-6) Performing the basic programming on the key items
2-6-1) “Numbering Plan” - change the station number if requested2-6-2) “CO Ring Assignment”
– Assigning which CO line incoming calls go to which station(s)2-6-3) “CO Group Access Station”
– Assigning which stations use which CO lines2-6-4) Change the default values for the most frequently requested features.
- COS(call restriction setting)- Flexible button assignment for digital/IP telephones- Registering system speed dial list- MOH(Music on Hold)- Doorphone installation- Date/Time change of the system
-------------- 3
-------------- 4
------------- 10
-------------- 15161718192021
Step 3) Advanced Programming3-1) DB upload / download (Page 36)3-2) Software upgrade3-3) E1R23-4) PRI3-5) Hunt Group – UCD3-6) Installing VOIB board3-7) IP Extension – Phontage3-8) IP Extension – IP Phone3-9) SIP Trunks3-10) Off-line PC-Admin3-11) LCR3-12) CCR
AppendixA. Customer Requirements Check-listB. Documentation Reference GuideC. Terminal User Guide
Digital / IP terminalsAnalog telephones
D. ipLDK-60 IP Network configuration guide
-------------- 35363840435052545658606163
67
Always Surpassing Customers Expectations3 LG-Nortel Confidential Information
Getting Started
This Quick Installation Guide provides the key steps to install and configure ipLDK-60 system. This guide is a light & integrated version of hardware and programming manuals. Among hundreds of features supported in ipLDK-60 systems, this guide provides the instructions to most frequently used features in small companies. This guide will help installers not only to understand ipLDK-60 system easily but also help to learn the capability to install and program very quickly.
This guide is composed of four parts as below.1) Overview
• This section is to give the basic introduction to ipLDK-60 system and the general description of the whole processes for installation and programming.
2) Step 1 : Hardware installation• This section describes hardware components, functions of each parts and overall hardware
installation procedures.3) Step 2 : Basic Feature Programming•This step provides the fundamental items necessary to program. Basic software operation & programming instructions will be given in this step.4) Step 3 : Advanced Feature Programming
• This gives the programming guides for advanced features. This is an optional part necessary to program with specific customer requirements.
Generally, Step 1 and 2 above cover most small customers’ typical requirements.For complicated programming to enable specific functions and features, the original manuals can be referred. In each section, the reference pages in manuals is provided. However, for beginners, it is recommended to fully understand this guide in advance.
Always Surpassing Customers Expectations4 LG-Nortel Confidential Information
Key Hardware componentsKey Service Unit (System)CO & Extension Interface BoardOptional Function Board
(VOIU, VMIU, AAFU, etc)Terminals (Digital, IP, Analog)Accessories (Relay, Alarm, etc..)
Basic FeaturesChange Station numbersCO Ring AssignmentCO Group Access Station AssignBasic Feature SettingsStation/CO COS, Flexible buttons, MOH, Doorphone
Advanced FeaturesDatabase Up/DownloadRemote Software UpgradeE1R2, PRIUCD, LCR, CCRIP Extension, SIP TrunksOff-line PC-Admin
1.Unpack and check hardwarecomponents (12p)
2.Open front cover of KSU (14p)3.CO & Extension Board / Option
Board connection (38p/49p)4.ipLDK-60 System Mounting (19p)5.MBU, EMBU connection (24p)6.Grounding KSU (17p)7.Backup Battery installation (18p)8.PSTN/E1/PRI cabling ( )9.Terminals cabling (51p)10.Accessories cabling
1.Install PC-Admin onto PC2.Connect PC to System3.Start PC-Admin4.IP setting (System, PC-Admin)5.Program major features as
instructed.
1.Check and Install necessary hardware components for Advanced Features (CCR-VMIU, IP-VOIU, etc)
2.Start PC-Admin3.Program advanced features as
instructed.
※ Declined lettering : Optional steps
Des
crip
tions
Inst
alla
tion
1. Overall Installation Procedure
Basic FeatureProgrammingStep2 Advanced Feature
ProgrammingStep3
Overview HardwareInstallation
Basic FeatureProgramming
Advanced FeatureProgramming
Hardware InstallationStep1
This is the overall steps to install and administer ipLDK-60 system. It will be very helpful to get this overall installation procedures in advance.
Always Surpassing Customers Expectations5 LG-Nortel Confidential Information
2.Understanding ipLDK-60 HardwareOverview HardwareInstallation
Basic FeatureProgramming
Advanced FeatureProgramming
ipLDK-60 hardware is composed of 3 categories. This part will give the overall list and brief description.The following figure shows the devices which connect to the ipLDK-60 system.
System Connection Diagram
3 Categories :
1. Main system- Basic system (BKSU)- Expansion system (EKSU)
2. Optional CO/Extension Interface Boards
3. Terminals - Digital telephones- IP telephones- Analog telephones- Accessories (MOH, Alarm, etc..)
Always Surpassing Customers Expectations6 LG-Nortel Confidential Information
Category Items Board Brief description
1.Main System
1) BKSU(Basic KSU)
MBU This is the basic system of ipLDK-60 that has the main system software running on CPU. (MBU is the mother board of basic system)This has basic CO/Extension interfaces and can be expanded with optional interface boards. (Basic – 3 CO line, 1 DKT & 7 Hybrid Interface)Option slots – one for capacity expansion, a MODU slot, VMIU/AAFU slot, VOIU Slot and CMU slot
2) EKSU(ExpansionKSU)
EMBU This is the expansion system of ipLDK-60 for capacity expansion. This is controlled by main system software of BKSU and only provides additional CO & extension interfaces. (EMBU is the mother board of expansion system – no CPU)This has basic CO/Extension interfaces and can be expanded with option interface boards. (Basic – 3 CO line, 8 Hybrid Interface)Option slots – one for capacity expansion, CMU slot
PSU BKSU and EKSU has its own power supply unit respectively.• 100~240 +/- 10% Volt AC input @47-63Hz, 90W
2.Optional CO and Extension Interface Boards
CHB308 (NTB417) 3 CO Lines and 8 Hybrid Interface Board
CSB316(NTB418) 3 CO Lines and 16 SLT Interface Board
SLIB8(NTB416) 8 SLT Interface Board
E1HB8(NTB419) E1R2 and 8 Hybrid Interface Board
PRHB8 PRI and 8 Hybrid Interface Board
VOIB(NTB422) Voice over IP Interface Board (4 Channels)
.Dual stacks of H.323 Revision4 and SIP Protocol The channel can be expanded to 8 channels with optional VOIU unit.
2.Understanding ipLDK-60 HardwareOverview HardwareInstallation
Basic FeatureProgramming
Advanced FeatureProgramming
Always Surpassing Customers Expectations7 LG-Nortel Confidential Information
Category Items Board Brief Description
2.Optional CO and Extension Interface Boards
VMIU(NTB420)
Voice Mail Interface Unit (4 channels)Max recording time : 123min (System greetings-24min, Users – 99min)Max number of voice messages (800 ea)
AAFU(NTB421)
Auto Attendant Function Unit (4 channels)Max recording time : 33min (System greetings-24min, Users – 9min)Max number of voice messages (800 ea)
MODU(NTB413) MODEM unit (33Kbps)
CMU50PR(NTB415)
This is an optional unit mounted on BKSU or EKSU (CN9/10) to detect the call metering signal for 50Hz and Polarity Reversal (3 channels)
CMU12PR(NTB414)
This is an optional unit mounted on BKSU or EKSU (CN9/10) to detect the call metering signal for 12KHz,16KHz or Polarity Reversal (3 channels)
3.TerminalsLDP-6212D (NTB424, NTB426)
Digital Key Telephone .3Line LCD, 12 Flexible Button Display.Dark Black(NTB424), Light Grey(NTB426)
LDP-6230D (NTB425,NTB427)
Digital Key Telephone.3 Line LCD, 30 Flexible Button Display.Dark Black(NTB425) and Light Grey(NTB427)
LIP-6012D(NTB433AA )
IP Telephone .3Line LCD, 12 Flexible Button Display
LIP-6030D (NTB434AA)
IP Telephone .3 Line LCD, 30 Flexible Button Display
LDP-6248DSS(NTB428) 48 Button DSS Console
LDP-DPB(NTB429) Door Phone Box
2.Understanding ipLDK-60 HardwareOverview HardwareInstallation
Basic FeatureProgramming
Advanced FeatureProgramming
Always Surpassing Customers Expectations8 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
Step 1 provides the steps to install hardware appropriately for each customer site.Based on customer requests, perform the installation as the following steps.
1-1) Unpack and check hardware components (Page 9)1-2) Open front cover of KSU (Page 10) 1-3) Connect CO & Extension Board / Option Board if necessary. (optional) (Page 10) 1-4) ipLDK-60 System Mounting (Page 11) 1-5) MBU, EMBU connection ((Page 12)1-6) Backup Battery installation (Page 12)1-7) Grounding KSU (Page 12)1-8) PSTN/E1/PRI cabling (Page 13)1-9) Terminals cabling (Page 13) 1-10) Accessories cabling (Page 13)
Always Surpassing Customers Expectations9 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
1-1) Unpack and check hardware components
Open the box and check the components shown in below figures.
BKSU Components EKSU Components
Basic Key Service Unit
Mounting Plate
Cables and Accessories Cables and Accessories
Expansion Key Service Unit
Mounting Plate
Relay connector
Tie cable
Anchor plug Screw Fuse
CD manual Power cord
Battery cable Rubber feet
Relay connector
Tie cable
Anchor plug Screw Fuse
CD manual Power cord
Battery cable Rubber feetTie cable
Anchor plug Screw Fuse
Power cord Battery cable
Link cable
Relay connector
Rubber feet
Jump wire
Tie cable
Anchor plug Screw Fuse
Power cord Battery cable
Link cable
Relay connector
Rubber feet
Jump wire
Always Surpassing Customers Expectations10 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
1-2) Open front cover of KSU
1-3) CO & Extension Board / Option Board connection Connect the necessary option boards at the right position described as in figure. If there is no option boards necessary, step 1-2 and 1-3 can be skipped.
PRHB8
Always Surpassing Customers Expectations11 LG-Nortel Confidential Information
19” RACK Mounting
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
1-4) ipLDK-60 System mounting There are generally 3 ways to install the system like WALL Mounting, RACK Mounting, DESK Mounting.Select the proper place to install the system.
1.Attach mounting plate on thewall with anchors and screws
2.Hook the System to the screwson the wall with sliding-down
Screw
Anchorplug
1.Attach the rack bracket to the bottom of the System
2.Affix the bracketed System onto 19” Rack with screws
1.Remove the backing paper of rubber feet
2.Attach the rubber feet to the bottom of the System
3.Mount the System on the Other
WALL Mounting DESK Mounting
Rubber Feet
Always Surpassing Customers Expectations12 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
BKSU/EKSU Linking Battery Connection and Frame Ground
1-5) MBU, EMBU connection This step is necessary to install both BKSU and EKSU. BKSU and EKSU can be connected via champ cable which is provided with EKSU system. This can be skipped only with BKSU installation.
1-6/7) Backup Batter installation and Grounding KSU
CAUTIONThe equipment should be connected to a socket-outlet with a protective ground connectionIt is recommended that the ground cable is shorter than 1m(3.28ft)It is recommended to use an external backup battery fuse (5A @250V)between the battery and the System
Always Surpassing Customers Expectations13 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
1-8/9/10) Cabling for PSTN/E1/PRI, Terminals cabling, Accessories cablingThe MBU provides various interface for cabling of the different type of terminals. RJ45 is for internet connection, RJ11 is for CO or Station line connection and so on. Refer to the bellow tables and do cabling for your purpose.
BKSU InterfaceTYPE PIN
NumberNO Signal
Name
RJ11 1,2 N/A
3,4 CO-T, CO-R
5,6 N/A
MBU CO (MJ1) MBU MJ1–1,2,3
TYPE Pin Number NO SIGNAL
NAMERJ45 3,6,7,8 RESERVED
1 TX+2 TX-4 RX-5 RX+
E1 Port ( E1HB8 ONLY)
TYPE PIN NUMBER NO SIGNAL
NAMERJ11 1 N/A
2 DKT-T3,4 ALARM_
Detection5 DKT-R6 N/A
TYPE PIN NUMBER NO SIGNAL
NAME
RJ11 1 N/A
2 DKT-T
3,4 SLT-T, SLT-R
5 DKT-R
6 N/A
MBU Extension(MJ2)MBU MJ2-1 (DKT ONLY) * MBU Extension (MJ2)–2,3,4,5,6,7,8
* notes :* notes :1) When installing DKT or SLT on Hybrid Ports, (MJ2-2,3,4,5,6,7,8), keep the
above pin assignment. Otherwise the DKT or SLT will not operate normally.2) Centered 2-wired cable is used for SLT connection, and 4-wired cable is
used for DKT connection each. But in case of DKT, just 2 outer ones of 4 wires are used actually.
2
1 2
3 4
1 3 4
Always Surpassing Customers Expectations14 LG-Nortel Confidential Information
HardwareInstallation Basic Feature
ProgrammingAdvanced Feature
Programming
1-8/9/10) Cabling for PSTN/E1/PRI, Terminals cabling, Accessories cablingThe MBU provides various interface for cabling of the different type of terminals. RJ45 is for internet connection, RJ11 is for CO or Station line connection and so on. Refer to the bellow tables and do cabling for your purpose.
TYPE NO SIGNAL NAME
4 PIN 1 Relay 1-pin1
2 Relay 1-pin2
3 Relay 2-pin1
4 Relay 2-pin2
TYPE Pin Number NO SIGNAL
NAMERJ45 4,5,7,8 RESERVED
1 TX+2 TX-3 RX-6 RX+
Relay Contact Pin Assignment (CN13) LAN (MJ3) Pin Assignment
TYPE COLOR FUNCTIONAudio Jack
RED External Music Source
TYPE COLOR FUNCTIONAudio Jack
BLUE External Paging
MBU External Music Source(PJ1) MBU External Paging(PJ2)
BKSU Interface
12
3
4
1 2
43
Always Surpassing Customers Expectations15 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
Step 2 provides the procedures to configure the basic-level features of ipLDK-60 system,which are mostly fundamental and typical in the real customer sites.Most steps in this section are necessary to be configured in order to get the most effective usage of the system. Detail settings may vary on site-by-site.
2-1) Initializing hardware configuration automatically (Page 16)2-2) Installing PC-Admin Program and connecting PC to the system (Page 17)2-3) Describing the basic menu trees of PC-ADMIN Program (Page 18)2-4) Setting the nation code as “Brazil” (Page 19)2-5) Understanding the default configuration (Page 20)2-6) Performing the basic programming on the key items (Page 21)
2-6-1) “Numbering Plan” - change the station number if requested2-6-2) “CO Ring Assignment” – Assigning which CO line incoming calls go to which station(s)2-6-3) “CO Group Access Station” – Assigning which stations use which CO lines2-6-4) Change the default values for the most frequently requested features.
- COS(call restriction setting)
- Flexible button assignment for digital/IP telephones
- Registering system speed dial list
- MOH(Music on Hold)
- Doorphone installation
- Date/Time change of the system
Always Surpassing Customers Expectations16 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-1) Initializing hardware configuration automatically
ipLDK-60 system software should be initialized at its first installation to properly read the hardware configuration. Get all the necessary interface boards assembled before power on.This initialization process applies only for the 1st hardware configuration. If hardware add-on cases, different procedure should be followed. Refer to the Hardware Installation manual for the details.
Procedure : 1) Complete all hardware installations and wiring.*2) Before system power on, check the SW1 DIP4 “on” at the
MBU on BKSU.3) Then, power on. System software automatically starts and processes the initialization which takes less than a minute.*4) Set the SW1 DIP4 “off” to protect from Database re- initialization after the initialization just in case of any types of system failure. This is the completion of this process.
Now, system is ready to provide the default call services, which will be explained at the next page.
Notes :System Database (DB) will be refreshed when it restarts in
any reason with SW1 DIP4 “on”.It is necessary to check the hardware configuration to
make sure that automatic initialization is properly performed.This can be checked at Pre-programmed/Configuration (PGM101~103).
SW1 DIP 4 “on”
SW1 DIP 4 “off”
*4)
MBU on BKSU
*2)
Always Surpassing Customers Expectations17 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-2) Installing PC-Admin Program and connecting PC to the system
There are two ways to do the programming of ipLDK-60 system - 1) PC-ADMIN, 2) Keyset-ADMINThis guide will be primarily based on PC-ADMIN. For Keyset based ADMIN, please refer to the programming manual.
4)
1), 2)
3)Direct LAN connection
1) Install PC-Admin S/W on your PC by running “Setup.exe” file of PC-Admin. Get the PC-Admin Setupfile at www.LG-Nortel.com.brPC Requirements :
Pentium Celeron 233M or above, at least 64MB RAM, MS Windows NT/2000/XP
2) Set the IP Address of PCIP Setting on PC : 192.168.1.x,Delete Gateway/Subnet field.Default IP of ipLDK-60 : 192.168.1.1
3) Connect PC and ipLDK-60 (LAN port on MBU) via LAN directly
4) Run the PC-Adminprogram on your PC. You will see the loginpop-up window.Input ID/Password
ID : “Administrator”P/W : “0000”
5
5-15-2
6 6-15) Go to Tools/ Site management. Input Name and System IP. Default : 192.168.1.1. and Save. Other fields are optional.6) Position the mouse on the Site and click the right button. Click “Connect(LAN)
7)Enter the connection password. (Default : no password – Just Enter)
You will see the main PC-Admin Window. Now you are ready to do the basic Admin.
7
Always Surpassing Customers Expectations18 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-3) Describing the basic menu trees of PC-ADMIN Program
This describes the basic level of menu architecture of PC-Admin program. Even though sophisticated administrations can be performed with this program, for the beginners, it is strongly recommended to simply follow the instructions and fully understand this guide in advance. Later on, complex levels of programming can be learned through the programming manual.
1) 2)3)
4)
5)
6) 7) 8) 9) 10)
1) System software category (Office Version only available)2) System Software Version with release time3) PC-Admin Program Version with release time4) Selected country and site name5) Programming menu tree. Each programming field can be
accessed by double clicking6) File
Connect / Disconnect to the system7) Tools
Site Information for multi-site information managementUser Management, Level management☞ Access authority to the programming menu in
different level can be managed8) Option
Language can be selected either Local or English9) LDK Utility
LDK DB upload/DownloadLDK Remote DiagnosticLDK UpgradeLDK Speed Editor PathLDK Speed Editor
10) Help at the last* Refer to the PC-Admin user guide for the details.
Always Surpassing Customers Expectations19 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-4) Setting the nation code as Brazil
It is necessary to set the system nation code as “Brazil” to load the default values for Brazil market as the first step.
1) Select the nation as “Brazil”at Location information (PGM100).
2) Check SW1 DIP4 “on” and click update
3) Reset the system by pressing the reset button on MBU. Then all default configuration for Brazil will be loaded
4) Position SW1 DIP4 “off” after the system reboot.
1)
2
4 3
Always Surpassing Customers Expectations20 LG-Nortel Confidential Information
Advanced FeatureProgramming
2-5) Understanding the default configurationOnce hardware installation(Step1) and initialization(Step2-1) are completed, ipLDK-60 is ready to provide basic call services as followings based on the default configuration prior to any programming.From this default operation, it is necessary to do the planning of the programming for the customer site.It is recommended to use the customer requirement check-list (refer to Page 68) for effective planning.
Default Numbering plan :1) CO and station port numbers are assigned as in figures by default.
CO number is assigned from left to right : CO1/2/3, CO4/5/6 at the upperStation number is assigned from left to right : 100~107, 108~115 at the upperSTA2(101) is set as the system attendant.
Default Call Operation :1) Incoming calls from any CO lines go only to STA2(101).
Then, STA2 can transfer the call to the other station as requested.2) For outgoing calls, press “0” followed by the destination number.
System will seize one of idle CO lines from CO1 to CO3 orderly by default for 308 basic case. There is no restriction pre assigned to make any type of calls
like local, long distance, international.3) For station to station internal calls, press the extension number directly.4) These call services are the same for 24 hours, set as Day mode.
Above default numbering plan & operation can be modified accordingly from the customer requests. These lists below can address most of typical requirements for small companies (Details are the Step 2-5)1) “Numbering Plan” - change the station number if requested 2) “CO Ring Assignment” - which CO line incoming calls go to which station(s)3) “CO Group Access Station” - which stations use which CO lines4) Change the default value for the basic feature operation such as call restriction
by station, MOH change, flexible button assignment for digital telephone and many more. ☞ These modifications depend on the customers demand.
Default configuration & operation
Basic FeatureProgramming
[308] Configuration
[616] Configuration
Always Surpassing Customers Expectations21 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6) Performing the basic programming on the key items
This part gives the instructions to the basic programming on the typical items for small companies.As explained in Step 2-5), the followings are most frequently requested items for basic programming.
2-6-1)“Numbering Plan” - change the station number if requested2-6-2)“CO Ring Assignment” – Assign which CO line incoming calls go to which station(s)2-6-3)“CO Group Access Station” – Assign which stations use which CO lines2-6-4) Change the parameters for the most frequently requested features.
- COS(call restriction setting)
- Flexible button assignment for digital/IP telephones
- Registering system speed dial list
- MOH(Music on Hold)
- Doorphone installation
- Date/Time change of the system
The terms in Parenthesis above are used for ipLDK-60 administration. Even though these terms are not general terms, it is important to understand the terms and concepts clearly. These are described in details in later-on sections.
Always Surpassing Customers Expectations22 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-1) “Numbering Plan” - change the Station Numbers and Feature Code if requestedBy default, the station number is set from 100~147 matched with the hardware port number as in the figure on the right. The station number can be changed by range or station by station. In addition to station number changes, there are several sets of feature codes available. Note that the station number should not be the same as the feature code numbers. For details, refer to the Programming manual.1)Change by range2)Change station by station 100 107…
108 115…
Station number change by station1) Go to Pre-Programmed/Numbering Plan(PGM104~109) in
the menu tree and double clicking.2) Position the mouse at the station number to change and
click the right button. Click again the Update Tool.3) Put the new station number and click “update station
number”
Station number change by range1) Go to Pre-Programmed/Numbering Plan(PGM104~109) in
the menu tree and double clicking.2) Position the mouse at the station number to change and
click the right button. Click again the Update Tool.3) Put the new station range and click “update station
number”
1)
2)
3) (Range)
3) (station)
Always Surpassing Customers Expectations23 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-2) CO Ring Assignment – Assigning which CO line incoming calls go to which station(s)By default, all incoming CO calls are switched only to STA2(101). This default call routing only to station 101 can be
modified generally in 3 ways as follows.- Incoming calls via specific CO line(s) can be programmed to go to a certain station or multi stations.- Incoming calls via specific CO line(s) can be programmed to go to a station group (Also called as “Hunt Group”.)- Incoming calls via specific CO line(s) can be programmed to go to DISA (This is for assigning AA(Auto attendant))
* If a CO line is assigned for DISA above, the system AA is activated. AA activation scenario will be explained in Step 3.** These incoming call distribution could be differently programmed among 3 options above by time of day. Default mode
is Day mode, which applies the same for 24hours. In this guide, the default operation mode will only be referenced. Therefore, any call distribution exampled here will be applied the same for 24 hours.
Here, the following 2 typical cases will be guided with examples.(The 3rd DISA case will be explained at Step 3-12 CCR)① CO1 calls go only to DKT1(100)② CO2/3 calls go to a station group (101~107) - Next page
with circular ringing -one station ringing at a time.
Assigning CO1 calls to DKT1(100) : 1) Go to CO Line Base Program/CO Ring Assignment
(PGM144/145) in the menu tree and double clicking.2) Choose CO line number “1” and press Refresh button.3) Click the right button of mouse and click “Update Tool”4) Select Mode as “Day”. Select Type as “Station”5) Input 100~100 at “Range Start” and “End”.6) Press “update” when you complete.
Deleting default-assigned STA2(101) from CO1 :Go to step 3) above. Input 101~101at “Range Start” and “End”. Mark “Delete Ring Assignment” at the bottom of the window. Click update.
Now, CO1 Incoming calls go only to DKT1 (100).
①
②
2)
4)
1)
3)5)
6)
Always Surpassing Customers Expectations24 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-2) CO Ring Assignment – Assigning which CO line incoming calls go to which station(s)
This is the 2nd example of CO line call distribution② CO2/3 calls go to a station group (101~107) with circular ringing -one station ringing at a time.
Assigning CO2 to STA2~STA7 (101~107) : 1) Go to CO Line Base Program/CO Ring Assignment(PGM144/145)
in the menu tree and double clicking.2) Choose CO line number “2” and “3”. press Refresh.3) Click the right button of mouse and click “Update Tool”4) Select Mode as “Day”. Select Type as “Hunt Group” and put the
group number “620”5) Press “update” when you complete.
Now, incoming calls from CO2/CO3 will go to STA2~STA8 (101~107). All idle stations will ring simultaneously.
3
2)
4)
1)
3)
5)
Before CO Ring Assignment, Hunt group should be pre- assigned in advance.
Assigning Hunt Group : 1) Go to Station Group/Station Group (PGM190/191) in the menu tree and double clicking.2) Click the right button of mouse and click “Update Tool”3) Select “Circular” as Group Type. 4) Select “on” for Pick-up group attribute.5) Add stations (101~107) from station list to Member field by
selecting the station and pressing “>” button.6) Press “update” when you complete.
Now, Hunt Group 620 is successfully established
1) 2)
3)4)5)5-1)
6)
5-2)
Always Surpassing Customers Expectations25 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-3) “CO Group Access Station” – Assigning which stations use which CO lines
By default, when a station tries an outgoing call, the system seizes a CO line from CO1 to CO3, which is in the idle status. This can be modified appropriately to the customer requirements.For example, system can be programmed that certain stations use only certain CO lines.Below are the steps for this programming.
① Divide CO lines as groups requested. By default, all CO lines are assigned as CO Group 1.② Then, assign a specific station or a station group to a CO group.
Default Configuration
For an outgoing call, a station can use any CO line which is idle in order. CO1~3 is grouped as CO group 1 by default.
Let’s assume a customer request as follows.CO1 is only used by Station 100CO2 and CO3 are shared by station 101~107
Programming steps to apply above examples.Assign CO2 and CO3 as CO Group 2Assign 101~107 to use Group 2 (CO2/CO3)☞ Detail procedures are on the next page
Example
Always Surpassing Customers Expectations26 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-3) “CO Group Access Station” - which stations use which CO lines
These are the programming procedure for the example.
Assigning CO2 and CO3 as CO Group 2 :1) Go to CO Line Base Program/CO Line list
(PGM140/141/142/143) in the menu tree and double clicking.2) Input CO line number “2” and “3”.3) Click the “CO Attr I” button. CO line Attribute I (PGM141)
window will pop up.4) Click the right button of mouse and click “Update Tool”
Update tool will be showed at the bottom side.5) Put the CO number “2” and “3”6) Select the CO Group as “2”.7) Click update button..
Assigning 101~107 to use CO Group 2 (CO2/CO3) andDeleting 101~107 from CO Group 1 (CO1)1) Go to Station base Program/CO Group Assess Station
(PGM117/131) and double click.2) Choose CO Group number as “2”3) Click the right button of mouse and click “Update Tool”4) Input the station number “101” at Start , “107” at End and click
Get button. 5) Mark the check box for Access CO Group 2 to add and
uncheck the check box for Access CO Group 1 to delete, which is assigned by default. Then, click Update button.
Now, CO2 and CO3 are grouped as CO group 2.And Stations 101~107 use CO group 2(CO2/CO3) as theirCO lines for outgoing calls.
2) 3)
4)
5)6) 7)
1)
1)2)
3)
4)
5)
5-1)
Always Surpassing Customers Expectations27 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
2-6-4) Change the default values for the most frequently requested features. These are the programming examples for the most frequently requested items from the customers such as COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.
> Station COS / CO COS (Class of Service)Station COS is to allow or deny types of calls from the internal stations with different levels of restriction/allowance rules.CO COS is to allow or deny types of calls on CO lines with different levels of restriction/allowance rule.By default in ipLDK-60, all stations and CO lines are assigned as COS level 1, no restrictions.So, any types of calls like long distance or international calls can be made from any stations through any CO lines. There are 9 different levels of COS setting (V3.7Ff version) on both station and CO, which can be applied in combination. This can be programmed on either station or COS or Both. Below is the rule table. Generally, station COS rules cover most of the requirements. For example, Station COS level 2 is ruled by Exception Table A. Station COS level 3 is ruled by Table B.
CO LINE COS
STATIONCOS
1 2 3 4 51 Unrestricted Unrestricted Unrestricted Canned
Restricted Unrestricted
2 Table A Table A Table B CannedRestricted Unrestricted
3 Table B Unrestricted Unrestricted CannedRestricted Unrestricted
4 Table A,B Table A Table B CannedRestricted Unrestricted
5 CannedRestricted2
CannedRestricted2
CannedRestricted2
CannedRestricted1 Unrestricted
6 CannedRestricted1
CannedRestricted1
CannedRestricted1
CannedRestricted1 Unrestricted
7 Intercom Only
Intercom Only Intercom Only Intercom Only Intercom Only
8 Table C Table C Unrestricted CannedRestricted1 Unrestricted
9 Table D Table D Unrestricted CannedRestricted1 Unrestricted
DefaultFor this assignment, follow below 2 steps.
① Make the exception table for allowance and denialfor certain numbers.
② Apply the COS levelon stations or CO lines
At next page, a simple example will be given.
Typical usage.
Always Surpassing Customers Expectations28 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Station COS / CO COS (Class of Service)
Making Toll exception table A :1) Go to Tables/Toll Exception table
(PGM 224) in menu tree 2) Click the right button of mouse and
click “Update Tool”3) Input “any access code” to allow and
press Update button. Repeat step 3 if you have other numbers to put in.If you put “002” here, it means that any calls which start “002” are allowed.
4) Click Deny A button right under Allow A.5) Input “any access code” to deny and press Update button. Repeat Step 5 if you have other numbers to put in. If you put “003” here, it means that all calls starting “003” is restricted.Now, this means only 002 is allowed. Other than 002, all number starting 00 will be denied.
Making Toll exception table A :1) Go to Station Base Program/Display Station
COS (PGM116/130) in menu tree 2) Click the right button of mouse and click
“Update Tool”3) Input the station range , “101” at start and
“107 at End. Select Day COS as “2” andNight COS as “2” and click Update button.
4) COS can be displayed. Put the station range to check and click View button. TheCOS will be displayed for day and night.
2-6-4) Change the default values for the most frequently requested features.
1)2)
3)
4)
5)
1)2)
3)
4)
Always Surpassing Customers Expectations29 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Flexible button assignment for digital telephoneFlexible buttons on digital/IP telephones can be programmed and used in many ways. On each flexible button, CO line, Station, Speed dial number or Frequently Used Functions can be assigned. With these assignment, the assigned function is executed with a click of the button. This assignment can be performed via PC-Admin Program very easily.This will be explained with examples with most typical cases. By default, Flexible button 1 to 8 are assigned as followings in left picture below. Both pre-assigned buttons and N/A(Not Assigned) buttons can be assigned with new designations as requested. Here most typical cases will be explained with examples.
1 13
2 14
3 15
4 16
5 17
6 18
7 19
8 20
9 21
10 22
11 23
12 24
1 7
2 8
3 9
4 10
5 11
6 12
CO1CO2CO3CO4CO5CO6CO7CO8LoopN/AN/AN/A
N/AN/AN/AN/AN/AN/AN/AN/AN/AN/AN/AN/A
CO1CO2CO3CO4CO5CO6
CO7CO8LoopN/AN/AN/A
[LDP-6230D]
[LDP-6212D]
Default Assignment1 13
2 14
3 15
4 16
5 17
6 18
7 19
8 20
9 21
10 22
11 23
12 24
CO1CO2CO3
100101102103104105106107
SS1SS2SS3SS4SS5SS6SS7SS8SS9SS10FunctionsN/A
[LDP-6230D]
Example Assignment
1. Assign station number 100~107 on Flex 5~122. Assign 10 Speed dial numbers (10ea) on Flex13~223. Assign Functions on Flex 23
2-6-4) Change the default values for the most frequently requested features.
Always Surpassing Customers Expectations30 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Flexible button assignment for digital telephone
1) 2 )
Update tool3 )
4 )
Assign station # 100~107 on Flex 5~12 respectively : 1) Go to Station Base Program/Flex Button
Assignment (PGM115/125) in menu tree2) Put the station number and click the Refresh.3) Click the right button of mouse and click
“Update Tool” again.4) Click the flexible number 4. Select Type as
{Station xxxx} and input the station numberas “100”. Then click Update button.
4-1) Repeat step 4 for flexible button 5~12 inthe same way.
Now, direct call can be made to the internal assigned station with one touch of the flexible button.
Assign 10 Speed dial numbers (10ea) on Flex13~22 :6) Click the flexible number 13. 7) Select Type as {System Speed xxxx} and input system speed bin number(storage number) as “2000”. Then click Update.7-1) Repeat above step 6 for flexible button14~22 in the same way as above
Assign Functions on Flex23 :8) Click the Flexible number 23. 9) Select Type as “Pickup” and Value as “Group call pick-up” and update.
6)
7)8)9)
2-6-4) Change the default values for the most frequently requested features.
Always Surpassing Customers Expectations31 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Registering system speed dial list via Speed EditorThere are two types of speed dial functions.1)System speed dial – The numbers can stored in the shared storage, upto 500 numbers. Number range : 2000~2499.2)Station speed dial – The numbers are stored in the individual storage, upto 100 numbers. Number range : 00~99.This gives the guide how to make the system speed number list via PC-Admin.These system and station numbers can be also stored via a station. Refer to the Programming manual for the details.
Linking the Speed Editor Program1) Get the speed editor program
from the CD-ROM for manualsor go to www.lgnortel.com.br
2) Run the PC-Admin Program3) Go to Utility/Speed Editor path
and click.4) Browse the path where Speed
Editor program is stored and click ok.
3)
4)4-1)
Connecting the system1) At PC-Admin, go to Utility/Speed Editor2) At Speed-Editor,go to Connection/Connect3) Set the IP Address of the system to
connect and click Ok. Click Connect again
1)
2)
3-1)
3-2)
3)3-3)
Downloading existing Speed- dial number from system1) Go to File transfer
/download2) Select the range.
Select where todownload
3) Then, open the file and update
UploadingThe updated Speed-dial number from system1) Go to File transfer
/upload2) Browse the file
and click ok
1)
2)
2-1)2-2)
3)
1)
2)2-1)
2-6-4) Change the default values for the most frequently requested features.
Always Surpassing Customers Expectations32 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Assigning MOH toneipLDK-60 system provides high-quality MOH (Music on hold). When a call is placed on hold, system provides a Music on Hold. There are 13 kinds of MOH in ipLDK-60. By default, “Romance” is pre-assigned and this can be easily changed as followings.
1) Go to System Base Program/Music (PGM171) in
the menu tree and double click.
2) Select any on the list.
2-6-4) Change the default values for the most frequently requested features.
2)1)
Always Surpassing Customers Expectations33 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> DoorphoneDoorphone can be installed on the front door of a company and a call by any visitor can be placed to the specific station (attendant). As well, automatic door open function can be assigned.
1) Choose the place for the doorphone and install it. For the detail guideline, refer to the Hardware installation manual. Cable the doorphone and any station port in the system as the same way for digital terminal cabling.
2) After hardware installation, following 2 cases need to beprogrammed.
Doorphone assignment for station 101 port should beset on (ICM Box signaling on)Flexible button for Doorphone (107) needs to be assigned on
station 101.
With this button set, the designated extension can receive thecall and open the door
3) For automatic door open, install proper relay on the door andcable to one of relay contacts (1~4). This example is the case to use relay contact 1
Then, you have to set this relay contact as for door open(PGM168)For door open, press (#*1) on the designated station.
Doorphone installation example
1) 2)3)DoorLock
2-6-4) Change the default values for the most frequently requested features.
Always Surpassing Customers Expectations34 LG-Nortel Confidential Information
Basic FeatureProgramming Advanced Feature
Programming
COS(call restriction setting), Flexible button assignment for digital/IP telephones, Registering system speed dial list, MOH(Music on Hold), Doorphone installation, Date/Time change of the system.> Doorphone
Assign station 101 as doorphoneextension :1) Go to Station Base Program/Station List
(PGM110/111/112/113/114) in menu tree.2) Put the station number for doorphone box
as “101” and click fresh. Click the right button of mouse and click “Edit Tool” .3) Check the ICM Box signaling “on”. Then
click “Edit OK”. Then click update for save.
Assign a flexible button on 101 as designated extension for doorphone : 4) Go to Station Base Program/Flex Button
Assignment(PGM115/125) in menu tree5) Put “101” at station number and click refresh.6) Choose a flexible button and click the right
button of mouse. Then click update tool7) Choose “Station xxxx” and input 107 at the Value position. then update.
Assign relay contact for automatic door open : 8) Go to Station Base
Program/External controlcontact (PGM168) in menu tree
9) Click the right button of mouseand click “Update Tool”. Setcontact as “Door open” andclick update.
2-6-4) Change the default values for the most frequently requested features.
1)
2)
3)
9-1
8)
9
7)
4)
5)
6)
ipLDK-60
Quick Installation GuideSimple integrated version of manuals for installation and programming
Step 3 – Advanced Feature Programming
Version 1.0
Always Surpassing Customers Expectations2 LG-Nortel Confidential Information
Advanced FeatureProgramming
Step 3 provides the procedures to configure the advanced features. With these features in properuse, a great deal of ipLDK-60 system features can be delivered to the customers.
3-1) DB upload / download (Page 36)3-2) Software upgrade (Page 38)3-3) E1R2 (Page 40)3-4) PRI (Page 43)3-5) Hunt Group – UCD (Page 50)3-6) Installing VOIB board (Page 52)3-7) IP Extension – Phontage (Page 54)3-8) IP Extension – IP Phone (Page 56)3-9) SIP Trunk Service (Page 58)3-10) Off-line PC-Admin (Page 60)3-11) LCR (Page 61)3-12) CCR (Page 63)
Always Surpassing Customers Expectations3 LG-Nortel Confidential Information
3-1) Database Upload/DownloadFor the effective management of system admin, DB can be easily downloaded and uploaded.During DB download, ipLDK-60 can be in normal operation. During DB upload, no admin changes are allowed by PC-Admin or Keyset Admin. After DB upload completion, ipLDK-60 will be reset automatically if “Automatic reset” is “on”
Advantages as follows- Database Backup/Restoration for emergence cases or any type of failures.- Downloaded DB file can be edited for upgrade or reuses for other similar customer sites without live connection to
ipLDK-60 Use “Off line PC Admin” program for off-line DB editing – refer to Step 3-10).- Local or remote connection is supported (LAN/Modem, *Serial connection - local only)
3-1-1) Database download 3-1-2) Database uploadHere, Up/download via LAN will only be explained (it is most simple)
Advanced FeatureProgramming
* Check system IP/gateway address in advance. (PGM108)1) Start the PC-Admin. Without system connection, click the LDK Utility/
LDK DB Upload/Download and select the system type as ipLDK-602) Select DB download and check “TCP Connection.
3) Input the system IP address to connect and Admin Password (No password by default.)* For remote connection, Public IP should be assigned on the connected system in advance.
4) Browse where to save with the DB name. Then click next. Downloading monitor trace box and progress window to be popped up (See the next page).
3-1-1) Database download
3)
4)
1)
1-1)
2)2-1)
Always Surpassing Customers Expectations4 LG-Nortel Confidential Information
3-1) Database Upload/Download
5) Click the Start button. DB download will be started.6) DB file transferring status will be shown with a pop-up window.7) Success pop-up will be shown if it is performed successfully.8) Click “No” to end.
3-1-1) Database download (Continued)
Advanced FeatureProgramming
3-1-2) Database Upload
Database upload can be done locally or from the remote site. The DB should be ready in advance.The overall procedures are quite the same as DB Download described at “3-1-1) Database download”
At step 2) DB upload should be checkedAt step 4) Browse the DB to upload.
Then, click the start at Step 5• Others are exactly the same as DB download
5)
6) 7)
8)
.2)
3)
4)
Always Surpassing Customers Expectations5 LG-Nortel Confidential Information
3-2) Remote Software Upgrade
System Software can be upgraded remotely via TCP/IP or Dial-up modem connection.With this capability, a lot of time and cost can be saved.
ipLDK-60 system should be assigned with an Public IP address in advance.* In local connection, private IP is ok. PC and system are set to be in the same zone.New system software(i.e. GS88P-38AP.bin) should be prepared in advance.Existing database in old software automatically fits into the new software.
* Check system IP/gateway address in advance. (PGM108)1) Start the PC-Admin. Without system connection, click the LDK
Utility/LDK DB Upgrade and select the system type as ipLDK-602) Select the connection type as “TCP Connection.
3) Input the system IP address and Admin Password (No password by default.)
4) Browse the system software to upgrade. Then, click next.
1)
1-1)
2)
3)
4)
Advanced FeatureProgramming
Always Surpassing Customers Expectations6 LG-Nortel Confidential InformationIf you press [Start] button, the transfer window will be displayed.
3-2) Remote Software Upgrade (Continued)
7) Once new software (GS88P-38AP.bin) is successfully transferredand verified, system disconnect the session and start replacing the old software with new software at Flash ROM.
Don’t touch anything on the system while system replacesoftwareAfter completing the upgrade, ipLDK system restartautomatically
8) Click “No” to end.
Advanced FeatureProgramming
5) Click the Start button. DB download will bestarted.
6) DB file transferring status will be shown witha pop-up window.
5)
6)
8)
7)
Always Surpassing Customers Expectations7 LG-Nortel Confidential Information
3-3) E1R2
TYPE Pin Number NO SIGNAL
NAMERJ45 3,6,7,8 RESERVED
1 TX+2 TX-4 RX-5 RX+
Cabling Guide
1) Install E1HB8 at CN2 on the BKSU
2) Wiring the cable between E1R2 and DSU equipment
3) Connect the E1R2 line on the port of E1H8 board.
* DSU and E1 line should be previded by a service provider in advance
E1HB8 supports E1R2 signaling. Full 30 voice channels or fractional channels are supportedas well. 3-3-1) E1R2 Board (E1HB8) Installation.3-3-2) Board Programming.
- Check the CO line numbers (range) – Full R2 channels (30channels), Fractional channels.- Assign CO type as DCO DID for R2 signaling.- Assign DCOB CO type for Both-way call service CO line”.* By default, E1R2 is set as Incoming DID line (Incoming DID call only – no outgoing call via this CO lines)
Advanced FeatureProgramming
3-3-1) E1R2 Board Installation
1)2)
Always Surpassing Customers Expectations8 LG-Nortel Confidential Information
3-3) E1R2
1)
2-1)
2)
1) Go to pre-programmed/configuration (PGM101~103) in the menu and double click.
2) Position the mouse on slot 6 “DCOB” and clickthe right button. Select “CO Data View”
3) Position the mouse CO line4 and click the right button. 4) Click again the “Update tool”
3) 4)
3-3-2) Board Programming
Advanced FeatureProgramming
Always Surpassing Customers Expectations9 LG-Nortel Confidential Information
3-3) E1R2
5) Input CO range. If 10 channels are used, put “ 4~13”.
6) Then, choose type as “DCO DID” for R2 signaling.Click update.
7) Input CO range “4~13”. Click Refresh. CO information to be popped.
8) Click the right button of mouse then click Update tool again.
9) Input CO range at 4~13. 10) Select DCOB CO type as 0(Cyprus) for both-way call.
Then update.
Advanced FeatureProgramming
3-3-2) Board Programming (Continued)
5) 6) 6-1)
7)7-1)
8)
9)10) 10-1)
Always Surpassing Customers Expectations10 LG-Nortel Confidential Information
Pre-requisite before PRI installation and programming. -“How many simultaneous calls(PRI Channels, which is CO lines)” and “how many DID numbers to use(Destination stations)” should be decided by the customer and contracted with the service provider.-Station numbers could be assigned the same as DID numbers subscribed from the Telco or can be assigned based on internal station number plan differently.-PRI channels(CO lines) are not directly dedicated to the specific station numbers. So, this should be handled by the system. To do so, ipLDK-60 should be programmed properly.-With the shared-use mechanism of PRI channels by any stations, it is required to give the caller’s ID (DID number) to the callee for any outgoing calls. In order to do this by ipLDK-60, it is required to be programmed as “outgoing caller ID assignment”- For any incoming DID calls, it is required to convert the DID number to the dedicated internal station number if the station numbering plan is different from the subscribed DID numbers.
Here, this will be explained with one of typical examplesa.10 PRI channels to be subscribed which will be assigned as CO4~CO13. (There is basic CO1~3 so, next 10 CO
channels are assigned from CO4 to CO13. if 30 channels are subscribed, it will be CO4 ~ CO33)b. Subscribed DID numbers are 031-450-5001~5024 (24 stations)c. Internal station numbers are assigned the same as the DID subscriber number.
Procedures to program the above case. 3-4-1) PRI Board (PRHB8) Installation on BKSU.3-4-2) Assign the station number from 5001~5023
refer to “Basic feature Programming – Step 2-1”3-4-3) Assign CO type as ISDN DID3-4-4) Outgoing Caller ID assignment
Station number conversion to DID number3-4-5) Incoming call assignment
DID number conversion to station number
3-4) PRI
Advanced FeatureProgramming
...
50015002
5024
PRI1) 10 PRI Channels
2) Subscriber numbers031-450-5001~5024
50015002
5024
Stationnumbers
DIDnumbers
Always Surpassing Customers Expectations11 LG-Nortel Confidential Information
3-4) PRI
TYPE Pin Number NO SIGNAL
NAMERJ45 4,5,7,8 RESERVED
1 TX+2 TX-3 RX-6 RX+
Cabling Guide
1) Install PRHB8 at CN2 on Basic MBU(BKSU). * DIP SW4 of PRHB8 should be at PRI position.
2) Wiring the cable between PRHB8 and DSU equipment as guided. (4wire cabling)
3) Connect the PRI line on the port of PRHB8 board.
* DSU and PRI line should be provided by a service provider in advance
Advanced FeatureProgramming
3-4-1) PRHB8 Board Installation on BKSU
1)
2)
3-4-2) Assign the station number If the basic numbering plan is to be used, this step can be skipped.If necessary to assign the station number, refer to the Step 2-1) the basic feature programming.
Always Surpassing Customers Expectations12 LG-Nortel Confidential Information
3-4) PRI
Assign CO4~33 as “ISDN DID”1) Go to pre-programmed/configuration
(PGM101~103) in the menu and double click.2) Position the mouse on slot 6 “PRIB” and click the
right button. Select “CO Data View”
3-4-3) Assign CO type as “ISDN DID”This is to assign the incoming calls to go to the destination directly.
3) Position the mouse at the CO number “4” and click the right button. Click the Update tool. Put the CO number range for “4~33”, select the type as ISDN DID. Click update.
4) Click CO ISDN Attr button on the right top side
Advanced FeatureProgramming
4)
3-1
3
3-2
3-3
1)
2-1)
2)
Always Surpassing Customers Expectations13 LG-Nortel Confidential Information
3-4) PRI
4) Input the CO range. Then Select CLIP Table Idx as “0”, Call type as “National”, CLI type(0~2) as “Normal”
and click update. Leave others unchanged.5) Then click the “CO Attr III” button.
6) Click the right mouse button on CO line 4 and clickthe update tool again.
7) Input the CO range. Then Select Outgoing prefix codeinsert as “off”. Then update.
Advanced FeatureProgramming
3-4-4) Outgoing caller ID assignmentSince the PRI channel is commonly used, the system should give the callers ID (DID number) to the PX on every outgoing call to give the right CID number to the callee. If this is not programmed, the PX will provide the caller ID randomly among the subscribed DID numbers, which will be wrong generally.
4)4-1)
4-2)
4-3)
5)
137)7-1)
7-2)
6)
5002 PRI5002031 450 5002
Area code
PX code
Subscribernumber
Always Surpassing Customers Expectations14 LG-Nortel Confidential Information
3-4) PRI
Assigning Area code8) Go to ISDN System base program/ISDN Attributes
(PGM200). Input area code “031” as in this example. Then update.
Assigning PX code9) Go to ISDN System base program/COLP Table
(PGM201). Position the mouse at Index 0 and clickthe right button of mouse. Click Update tool. Input “450” then update.
* No need to assign the subscriber number because it’s been already assigned the same between the station number and DID number.
Advanced FeatureProgramming
8)
8-2)
8-1)
3-4-4) Outgoing caller ID assignment (Continued)
9-1) 9-2)
9-4)
9)
4509-3)
Always Surpassing Customers Expectations15 LG-Nortel Confidential Information
3-4) PRI
10) Go to CO Line Base Program/CO line list (PGM140/141/142/143).Then, Go to CO ISDN Attributes(PGM143) byclicking “CO ISDN Attr”
11) Position the mouse at CO number 4 and clickthe right button. Click again “Update tool”
12) Input the CO range number “13”, Check DIDremove number as “0”. Click update.If the station number and DID number is
different, this should be checked accordingly.
Advanced FeatureProgramming
3-4-5) Incoming call assignmentIncoming calls are distributed with the number provided from the Telco PX, which is 3-digit or 4digit at the last. Need to check with the carriers. ipLDK-60 should be programmed accordingly with these numbers from the Telco to the destination.
5001 PRI5001031 450 5001
5024 5024
031 450 5024
10) 10-1)
11)
12)12-2)
12-1)
13)
13
13
11-1)
0
Always Surpassing Customers Expectations16 LG-Nortel Confidential Information
3-4) PRI
13) Go to CO line Attribute III(PGM146) byclicking “CO Attr III” or directly click thePGM146 at the menu tree.
14) Position the mouse at CO line number
“4” then click the right button.
Click the Update tool
15) Input the CO range as “13”. Select DID
RCV Digit Number as “4”. Input DID
Digit Conversion ****. Then update.
Advanced FeatureProgramming
3-4-5) Incoming call assignment
13-1)
13)
14) 14-1)
15)15-1)
15-2)
15-3)4
****
Always Surpassing Customers Expectations17 LG-Nortel Confidential Information
3-5) Hunt Group
Stations can be grouped for incoming call routing and Call Pick-up purposes. 7 types of groups can be defined in ipLDK-60, called as “Hunt Group” as a representative term for these groups. A type of group can be selected and programmed appropriately for the customer site usage. UCD(Uniform Call Distribution) will be exampled as the most typical type for small companies at next page
Group Type Description
Circular A call is routed to hunt group. If first destination is unavailable or unanswered, the call is routed to the next station in the group.
TerminalIf the call is unanswered or unavailable, it is directed to the next listed station in the group. The call will continue to be routed until reaching the last station in the group.
UCD Calls are routed to the station in the group that has been idle for the longest time.
Ring All stations in the group will ring when a call is received.Voice Mail
This group is assigned for Voice Mail and only the SLT assigned as the member of the VM group.
Pick-upA station can be assigned to a Call Pick-Up group and then may pick-up (answer) calls to other stations in the group employing the system’s Group Call Pick-Up feature.
Net VM Group
This group is defined to support a Centralized Voice Mail system for a networked environment. At supported systems, the group is used to handle the AA/VM requirements from the central iPECS. The Net VM group may be an external VM system or the iPECS Feature Server.
For example, Station 100~103 are grouped as “Ring” and station 104~107 are groupedas “UCD”
1) Incoming calls to UCD group. A call is routed to the idle station in thelongest among UCD group stations.
2) Incoming calls to Ring group.All stations will ring at the same time withnew call.
100 101 102 103
104 105 106 107
CO1 call
Ring Group
UCD Group
CO2 callCO3 call
CO1~3
Advanced FeatureProgramming
Always Surpassing Customers Expectations18 LG-Nortel Confidential Information
3-5) Hunt Group - UCD
Calls are directed to the station in the UCD group that has been idle for the longest time. If all stations are busy or unavailable when the call is received, the call may be routed to an alternate location or may continue to wait (queue) for an available station in the group. After queuing to the group, the caller may be routed to an overflow destination, which can be a Station, Station Group or Voice Mailbox. Here, only key operations will be guided. For details, refer to the Programming manual.
3-5-1) Make a Hunt Group as “UCD”3-5-2) Assign CO Ring Assignment
Assign CO Ring Assignment to UCD Group : 1) Go to CO Ring Assignment(PGM144/145). Position the
mouse at Day field then Click the right button of mouse.Click Update tool.
2) Select Mode as Day, Type as Hunt Group, and Numberas “620”. Then Update.
Advanced FeatureProgramming
4)
5)4-1)
5-1) 5-2) 5-3)
5-4)Make a Hunt Group as “UCD” : 3) Go to Station Group(PGM190/191). Position the mouse at group
620. Then click the right mouse button. Then click Update toolagain. Update tool will be popped up.
4) Select the stations from the station list. Then click “>” to add inUCD member list.
5) Select Group as “620”, Type as ”UCD”, Pickup attribute “On”.Then update.
1) 1-1)
2)
3)3-1)3-2)2-1)
2-2)
3-3)
Always Surpassing Customers Expectations19 LG-Nortel Confidential Information
3-6) Installing VOIB Board
VoIP Interface Board should be installed to use VoIP features such as IP phone, Softphone or SIP trunk service from ISPs or multi ipLDK-60 networking over IP. There are VOIB and VOIU, which supports 4 VOIP channels respectively. VOIB is mounted at CN14 on the basic MBU and VOIU is mounted on VOIB. The overall procedures to implement any VOIP features are
1) Install the VOIB board and Board Programming2) Then, Enable any VoIP Services to use : IP Phone, Phontage (Basic mode only), SIP Trunk Service
Procedure to Install VOIB Board :Install the VOIB(4ch only) or VOB/VOIU (4+4ch=8ch) on basic MBUSet the IP/Gateway address of VOIB via PC-Admin. IP should be prepared with a public IP address.Set the number of channels for IP Phone use and IP Trunk use.
2) Go to Pre-Programmed/Configuration(PGM101~103). Position the mouse on VOIB. Then, Click the right button of mouse. Click again “VOIB Data View”(PGM340/341)
3) Input the IP and Gateway Address.4) Check the SW1 DIP4 at “Off” position to save the new settings.5) Click update. VOIB Board will be automatically reset.
1) Install the VOIB (with VOIU) on the slot 10.Then, connect PC Admin tothe system for VOIB Board Programming
Advanced FeatureProgramming
1)
4)
2)2-1)
2-2)
3)3-1)
5)
Always Surpassing Customers Expectations20 LG-Nortel Confidential Information
3-6) Installing VOIB Board
Enabling the VOIB to be used for IP Extensions : 1) Go to Configuration (PGM101~103). Position the mouse
at VOIB. Click the right button. Click “Logical Assignment”2) Position the mouse on 10)VOIB then click the right
button. Select “(Virtual VOIB) Append to STA”.“99” will be added to STA board column. Click update.
Assigning the number of VOIP channel for IP extension & of the maximum IP extension number : 3) Go to RSG/IP Phone Programming/VOIB Slot for
RSG/IP(PGM380)4) Select VOIP slot for RSG/IP and click “>” to add.5) Select VOIP slot as “10”6) Select number of VOIP channel and click update.7) Select the number of IP extensions to use and update8) Click the update on the top to complete.9) System should be reset to database rearrangement
Advanced FeatureProgramming
2)
1)
1-1)
2-2)
2-1)
3)
4)
5)6) 6-1)
7) 7-1)
8)
Always Surpassing Customers Expectations21 LG-Nortel Confidential Information
3-7) IP Extension - Phontage
Phontage is the LG-Nortel proprietary IP Softphone that works only with LG-Nortel ipLDK-60 system. (Phontage Basic version only). Phontage is controlled by License system so the license by copy should be purchased and installed in the system. Basically 2 copies are embedded as free of charge.
1) VOIB Board should be installed. (VOIB-4ch, VOIB+VOIU -8ch)2) License for Phontage Basic (LIP-SP) should be downloaded and installed on the system.3) Set the system4) Install Phontage program on the PC
1) Go to LDK Utility/LDK Remote Diagnostic at theMenu Bar on the top
2) Connect via LAN (Input the IP Address at the LANconfigure. Then click the LAN connect. Input Password “jannie”
3) Input the command “q d”. 4) The license status can be checked.
1) Get the lock-key requiredthrough LGN Lock-keydownload Web-site(Refer to the Lock-keydownload guide”)
2) Open the “Telnet”connection to thedestination system.
3) Input password “jannie”4) Input license installation
command followed bylicense. “q w 9 (lock key)”
5) Check if the license isproperly installed with thecommand “q d”
6) Reset the system.
Advanced FeatureProgramming
2)
3)
4)
Always Surpassing Customers Expectations22 LG-Nortel Confidential Information
3-7) IP Extension - Phontage
Registering User ID/Password for the phontage users :1) Go to IP Phone Attribute (PGM386). Position the mouse at Bin No 1
and click the right button. ID/Password setting menu to be displayed at the bottom.
2) Input the ID/Password for Phontage for each user.3) Repeat Step 2 until complete all the users ID and Password. Update.
Now, the phontage users can login in with the pre-registered IP/Password.
Installing the Phontage Software on user’s PC :1) Get the Phontage Software from distributors/Resellers.2) Install the Phontage Basic program. Follow the installation wizard
Setting the Network and Login :1) Start the Phontage client software on the PC. Log-in
window to be popped up. Click the “Network” button to set the network configuration.
2) Check the connection mode as “Remote”.3) Input the VOIB IP address. Click OK.4) Enter User ID/Password, pre-programmed at PGM386.5) The main window will be popped up
(Refer to the user guide for the detail operation.)
Advanced FeatureProgramming
1) 2), 3)
1-1)
3-1)
1)
2)3)
4)
5)
Always Surpassing Customers Expectations23 LG-Nortel Confidential Information
3-8) IP Extension – IP Phone
Advanced FeatureProgramming
LG-Nortel IP phones (LIP-6030D, LIP-6012) can be registered in ipLDK-60, which can be installed in the company LAN or outside, for example at home remotely. Up-to 16 IP Terminals (including Phontage) can be registered in the system and the maximum simultaneous call depends on the VOIB/VOIU channels upto 8 channels.1) VOIB/(VOIU) should be installed in advance2) Register the MAC address of IP Phones to get the authentication from the system – get the MAC address from the bottom side of the phone.3) IP Phone programming
LAN
LAN(VOIB)router
LIP-6030D LIP-6012D
LIP-6030D
Phontage
Registering the MAC address of IP phones :
1) Go to RSG/IP Phone Programming (IP Phone
Attributes (PGM386).2) Position the mouse at the MAC Address and click
the right button. Click Update tool.
3) Input the MAC address of IP Phones one by one.
“ : “ should be inserted between 2-digit number.
Then, update.
1)
2)
3)
3-1)
Always Surpassing Customers Expectations24 LG-Nortel Confidential Information
3-8) IP Extension – IP Phone
Advanced FeatureProgramming
1) Power on the IP Phone. the following message will be displayed on LCD. Press”*” to enter the setup. If password requested, press “1 4 7 *” by default.
2) The following message will be shown. Leave the mode as “Remote” as default set. Move the menu to the next by using Volume up/down button. To change(Toggle) the value press “#”.
3) Input the IP Address of system(VOIB).Press “Hold/Save” button to save. Press “Speaker
4-a/b) Set DHCP enabled or input fixed IP address for the IP phone. In general, DHCP mode at home and Fixed IP mode at office.
5) Upon completion, press “Hold/Save” then press“Speaker. It will be rebooting to get connected to the system.
IP Phone should be programmed on the phone.1)Install the IP Phone and Cabling.2)Setting the Mode as Remote (ipLDK-60 only supports remote mode. So, it should be set as Remote” both at local and at remote connection.3)Setting the IP address of system (VOIB)4)Setting the IP address of IP Phone : At home => DHCP mode , at company => Fixed or DHCP5)Rebooting. IP Phone tries to connect to the system and connected.
NO RESPONSE FROM MFIM[L]SET[*] - RETRY[#]
MODE[R/L][REMOTE] - CHANGE[#]
PHONE IP ADDRESS(DOT:*)150.150.140.204
REBOOTING…AFTER SETTING
PHONE NET MASK(DOT:*)255.255.255.0
ROUTER IP ADDRESS(DOT:*)150.150.140.254
DHCP ?[DISABLED] CHANGE[#}
MFIM IP ADDRESS(DOT:*)150.150.140.214
1
2
3
4-a
4-b
5
Always Surpassing Customers Expectations25 LG-Nortel Confidential Information
3-9) SIP Trunk Service
Selecting VOIB mode as “SIP” trunk :1) Go to VOIB/Gatekeeper setting (PGM340/341).
Before this VOIB address should be properly installed.2) Set VIOB Mode as “SIP” and update.
Setting SIP trunk as Incoming/outgoing mode :3) Go to CO line list (PGM140/141/142/143). Insert CO
Number of VOIB Board.4) Position the mouse on the first CO number and click
the right button. Click Update tool5) Put the CO Number range at End. Select Type
“ISDN DID”. Update.
Advanced FeatureProgramming
ipLDK-60 has been homologated for a list of carriers’ softswitch so a certain level of SIP trunk service can be provided. The compatibility to the carriers softswitch should be checked in advance. If it is not in the list, the IOT should be processed first.1)VOIB installation – refer to “3-6”2)SIP Trunk Compatibility check - refer to the attached – the compatible list.3)SIP Trunk programming.
LAN
LAN(VOIB)router
SIP Phone
SIP Server(VOIP Carriers)
SIP Trunk
1)1-1)
2)
2-1)
4)3)
5) 5-1) 5-2)
3-1)
Always Surpassing Customers Expectations26 LG-Nortel Confidential Information
3-9) SIP Trunk Service
Setting SIP CO line attributes :6) Go to Network/Networking CO line Attribute (PGM322).7) Input SIP CO range and click refresh button.
Position the mouse at the first CO line number and click the right button. Click update tool.
9) Input the CO line range, Networking CO Group as “1”, VOIP Mode as “SIP”. Click update.
Setting SIP Proxy/Domain Server Address :10) Go to VOIB/Gatekeeper / SIP Attribute 1.11) Input SIP Proxy Server and Domain Address.
Get these addresses from the ISP in advance.Update.
Advanced FeatureProgramming
6)
7)7-1)
7-2)
8) 8-1) 8-2)
10)
11)
11-1)
11-2)
Always Surpassing Customers Expectations27 LG-Nortel Confidential Information
3-10) Off-line PC Admin
1) “xxx.usr” data file should be downloadedfrom DB up/download menu of On-line PC-Admin.
2) Run the Off-line PC-Admin withoutconnecting system and make modifications.
3) Save the changed date base as “yyy.usr” file.
4) Upload to the system via DB up/download menu of On-line PC-Admin.
*PC-Admin and PC-Admin Pro can reside on the same PC or different PCs.
ipLDK-60 can be administered via PC-Admin program by connecting PC and system in real time. In this case, any changes are applied in real time while operation. On the other hand, administration can be performed without connecting PC and system, which is called Off-line PC-Admin. In this case, any changes will be saved as database file(xxx.usr) and should be uploaded to get it applied to the system.2 different admin programs are provided.
1) On-line PC-Admin - “PC-Admin” Refer to the step 2-3) or PC-Admin user guide2) Off-line PC-Admin - “PC-AdminPro” Quick instruction will be given here.
DB(xxx.usr)(yyy.usr)
Off-linePC Admin
On-line PC Admin
1)2)3) 4)
Advanced FeatureProgramming
Open the DB
Modifications Save
Always Surpassing Customers Expectations28 LG-Nortel Confidential Information
3-11) LCR
LCR is a system programmable feature that automatically selects the least expensive available route when an outgoing CO call is made. With this feature enabled properly, system automatically convert to the least cost route when a user dials any access code. As well, this feature can be differently programmable by time during day and night and by day during week.
Telco A(001)
Telco B(002)
Telco C(00700)
1) Planning the LCR route with the customer (Routes, Time zone, Day zone)
2) Select LCR Access code and day zone and time zone3) Make LCR Table (LDT-Least Digit Table)4) Make DMT Table (DMT-Digit Modification Table)
Assigning LCR Access Code and Day/Time zone :1) Go to Tables/LCR Assignment(PGM220).2) Select LCR Access Code as “M12 / Internal, Loop, Direct
CO LCR”. Set the Day Zone as requested.In this example, it’s skipped. (For details, refer to xxx)
3) Set the Time zone as ZONE1 (6~21), ZONE2(0~5),Zone3(22~23)
*Note :There are 6 LCR Access Codes are available depending onhow to access the CO line like Internal LCR, Loop LCR,Direct CO LCR. Above M12 in this example covers all above cases.
Advanced FeatureProgramming
Always Surpassing Customers Expectations29 LG-Nortel Confidential Information
3-11) LCR
Assigning LCR Table, which is called “LDT Table” :
1) Go to Tables/LCR-LDT Table(PGM221).2) Position the mouse at Index “0” and click the right button.
Click again the Update tool. Input any network accesscode at “Compared digits” and select the time zone to be compared and click update.
* Note :This code will be automatically replaced with theother code at DMT table as set. (To be explained atthe right)
3) Repeat step2) above if there are more access codes tobe replaced with other code.
Assigning DMT Table :4) Go to Tables/LCR-DMT Table(PGM222).5) Position the mouse at Index “0” and click the right button.
Click again the Update tool. Input any network accesscode at “Added digits” and select the time zone and click update. * Note :
This code will automatically replace the access codein LDT table based on the time zone rule.
6) Repeat step5) above if there are more access codes tobe replaced with other code.
Advanced FeatureProgramming
1)2)
2-1)
3)
2-2)
2-3)
<Assigning the day zone and time zone>
4)5)
5-1) 5-2)5-3)
Always Surpassing Customers Expectations30 LG-Nortel Confidential Information
3-12) CCRCCR is the programmable feature that provides the announcement for the callers to select the destination.When a call is answered by a system programmed with CCR, a VMIB announcement should be heard by the caller. VMIB announcement gives a choice of destination and the caller may select a destination based on the information presented in the VMIB Announcement. Below is a typical example for operation. Procedure and Check point : 1)CCR Scenario planning 2)VMIU or AAIU should be installed.3)Announcement should be recorded as the scenario.4)CO lines should be assigned as “DISA” to provide this announcement service.5)CCR programming.
Level2) Announcement for Support team“Hello, This is Support Team. Please dial desired station number. If you don’t know, dial 1 for James (STA106), dial 2 for Thomas (STA107) and dial 0 for operator. Thank you.”
Level2) Announcement for Sales Team“Hello, This is Sales Team. Please dial desired number. If you don’t know, dial 1 for Sales 1 part(Hunt 620), dial 2 for Sales 2 part (Hunt 621) and dial 0 for operator. Thank you.”
Level1) Announcement “Hello, this is xxx Company. Please dial the extension number. If you don’t know the number, dial 1 for Sales Department, dial 2 for Technical Department and dial 0 for Operator. Thank you.”
Operator101
102 103 104 105
106 107
Hunt Group 620 (UCD Group)
Hunt Group 621 (Ring Group)
James Thomas
Caller
Advanced FeatureProgramming
CCR Scenario Planning▶ ‘2 level-CCR’ case is exampled : A new call comes in, ipLDK-60 gives the company announcement #1 at Level1)Case 1) If the caller selects ‘1’ :☞ The call will be routed to “sales team”Level2) If “1” selected,☞ The call goes to sales1 part as Ring
group operationLevel2) If “2” selected,☞ It goes to sales 2 part as UCD group
operation
Case 2) If the caller selects ‘2’ :☞ The call will be routed to “Support team”Level2) If “1” selected,☞ The call goes to James (106)
Level2) If “2” selected, ☞ It goes to Thomas (107)
Case 3) If the caller selects ‘0’ :☞ The call goes to the operator
Always Surpassing Customers Expectations31 LG-Nortel Confidential Information
3-12) CCR
VMIU/AAFU InstallationVoice Mail Interface Unit (VMIU) or AA function Unit (AAFU) should be installed to provide company announcement services such as system announcements, ACD/UCD announcements, and User Greetings. VMIU/AAFU provides the same services with different memory capacity.
1) Install VMIU or AAFU at slot #9 (CN5) on BasicMBU
VMIU AAFUChannels 4 4Max record time 123 33- System Greeting 24 24- User record time 99 9
Max number of recorded messages 800 800
Advanced FeatureProgramming
* VMIU vs AAFU
Assigning the CO lines as “DISA” lineThe incoming CO lines are needed to be assigned as “DISA to give this service.
1) Go to CO Line Base Program/CO Line List(PGM140/141/142/143)
2) Input the CO line range to be assigned as “DISA”. And click refresh.
3) Position the mouse at CO Num 1 and click the right button and click update tool.
4) Input the CO line range. Select the DISA “On” at Day checkbox. Input the VMIB msg number (storage number) and click update.
1) 2)2-1)
3)
4) 4-1) 4-2) 4-3)
Always Surpassing Customers Expectations32 LG-Nortel Confidential Information
3-12) CCR
Advanced FeatureProgramming
Direct Recording the announcements via the attendant station :1) For level 1 announcement, press [ TRANS/PGM ] + 0 6 + 0 1 (Storage
number) at the attendant station(101).2) To start record, press # and then record Level 1 Announcement. Press
[ HOLD ] to end the recording. This will be saved at VMIB storage number 1.3) For level 2-1 announcement, press [ TRANS/PGM ] + 0 6 + 0 2
at the attendant station (101). 4) To start record, press # and then record Level 2-1 Announcement. Press
[ HOLD ] to end the recording. This will be saved at VMIB storage number 2.
5) For level 2-2 announcement, press [ TRANS/PGM ] + 0 6 + 0 3 at the attendant station (101).
6) To start record, press # and then record Level 2-2 Announcement. Press[ HOLD ] to end the recording. This will be saved at VMIB storage number 3.
Pre-recording at the studio and uploading via the attendant station :1) Get the announcements recorded in advance and connect the source device
to the External MOH port in the system as in the figure.2) To upload the announcements, press [TRANS/PGM} + 0 6 + 0 1 at the
attendant station. Press # and start the announcement at the source device. Press [Hold] when it’s completed.
3) Repeat for 2nd and 3rd announcements as above.
Pre-recordedannouncements Attendant Station
(101)
Always Surpassing Customers Expectations33 LG-Nortel Confidential Information
3-12) CCR
Advanced FeatureProgramming
Assigning the 1st level scenario :1) Go to Tables/Customer Call Router
(PGM228).2) Select the Index as “1” meaning for
the 1st level scenario.3) Select the 1st destination as VMIB
and input 2 for the 2nd announcement.4) Select the 2nd destination as VMIB
and input 3 for the 3rd announcement.5) Click update.
Assigning the 2-1 level scenario :6) Select the Index as “2” meaning for
the 2st level scenario7) Select the 1st destination as Hunt
Group and input 620.8) Select the 2nd destination as Hunt
Group and input 621.9) Click update.
Note that Hunt Group 620/621 should be assigned properly in advance as thescenario.
Hunt Group 620 : Station 102/103Hunt Group 621 : Station 104/105
Assigning the 2-2 level scenario :10) Select the Index as “3” meaning for
the 2-2 scenario.11) Select the 1st destination as Station
and input 106.12) Select the 2nd destination as
Station and input 107.13) Click update.
1)
2)3)4)
5)6)
9)
7)8)
10)13)
11)12)
Always Surpassing Customers Expectations34 LG-Nortel Confidential Information
Appendix
A. Customer Requirements Checklist
B. Documentation Reference Table
C. Quick Terminal User Guide
D. ipLDK-60 IP Network Configuration Guide
Always Surpassing Customers Expectations35 LG-Nortel Confidential Information
A. Customer Requirements Checklist
Check lists Example Customer Requirements Recommendation
1.How many stations (Digital, Analog, IP, Softphone)?
2.How do you like station numbers? Default : 100, 101, 102, …New : 1000, 1001, 1002, …
3.Do you want to make station groups & how to give ring? (All ringing, Circular, UCD, etc)
G1 : 100~103(All ringing)G2 : 104~107(UCD ringing)
4.How many CO lines (CO, R2, PRI)? CO-6 lines or R2-10 channels
5.What are the numbers? CO1~3 : xxx-xxx1~xxx3
6.How to dedicate CO lines to stations? (CO Ring Assignment)
CO1 Group1CO2/3 Group2
7.Other stations can pick-up the call for other stations? Yes or No
8.Outgoing call access to CO lines from stations? (CO Group Station Access)
100 CO1101~107 - CO2/3
9.Specific Features
1) Company Greetings scenarios Yes or No
2) Outgoing call restriction by stations Yes or No
3) Specific network services (access code) Yes or No
4) Speed dial planning Yes or No
5) Flexible button assignment for digital/ip keysets Yes or No
6) Remote IP/Softphone Yes or No
Always Surpassing Customers Expectations36 LG-Nortel Confidential Information
B. Documentation reference guide
items RemarksQuick Installation Guide(HW & SW)
ipLDK-60 QIG
Hardware Installation Manual Global_ipLDK-60 IM_Issue1_1.doc
Software Programming Manual
Global_ipLDK-60 programming_Issue1_1.doc By PGM number
Global_ipLDK-60 Feature Description_Issue2_0.doc By Features
User guide for ipLDK-60 PCADMIN v381 To Brazil.doc
User guide for PCAdminPro_ipLDK60_V381_20080109.doc
SWUpgrade_Manual_IpLDK60.doc
DBUpDown_Manual_ipLDK60.doc
LG-Nortel TSP User Guide 37Aa.doc
Lock-key download manual
Application User Guide
ez Phone User Guide_ipLDK-60.doc
User Guide for ezATD_issue2.doc
Phontage User Guide _issue1.doc
Terminal User Guide
ipLDK-60_LDP_6212_30D_UG for digital telephones
ipLDK-60_LIP_6012_30D_UG for IP telephones
SLT User Guide for analog phones
These are the manual & user guide lists for ipLDK-60.All manuals are available from CD-ROM on the main system and LG-Nortel Web-site (www.lgnortel.com.br)* Note that the manual names and versions are subject to change
Always Surpassing Customers Expectations37 LG-Nortel Confidential Information
No. Buttons Functions1 Handset Handset device
2 Earphone socket Headset connection
3 Speaker phone Output tons and voice
4 SPEED Used for Speed dialing, Speed programming, Save number redial, Last number redial
5 DND/FWD DND (Do Not Disturb) : Blocks all incoming calls (Red LED)
FWD : Forward to another station or voicemail (Red LED)
6 Volume Adjust audio level for ringing, handset and speaker phone
7 ON/OFF Speaker toggle button (ON/OFF)
8 HOLD/SAVE Put a call hold or save information when programming
9 3 Soft Keys Select or setup various function(s) indicated on LCD panel in relation to call process. Ex) “PICKUP/CONF/REDIAL” in Idle Status (Please see Keyset manual for detailed functions)
10 LCD Information display and program setup
: Telephone status / Dialing directories / Test messages
11 LED Lighting when the phone is ringing
12 Trans/PGM Initiate call transfer function or enter programming mode
13 CALL BK A station can initiate a call back request to busy station.
: Leave a call back request or voice message to
destination station in busy status
14 Flexible buttons Assign some functions to the flexible buttons
Direct station selection, Call park, Speed dials buttons, etc..
Ring type, Set Wake-up Time, etc..
Button assignment (CONF,DND, MUTE, LOOP,..)
15 Handsfree MIC. Using with handsfree speakerphoneCable connection
LDP-6230D
Digital Phone / IP PhoneC. Terminal User Guide
Always Surpassing Customers Expectations38 LG-Nortel Confidential Information
No. Functions Description1 Placing an Outside Call Dial 9
2 Placing an Intercom Call Dial Intercom Number directly3 Last Number Redial Dial 5 5 24 Group Call Pick-up Dial 5 6 65 Call Forward Dial 5 5 4 and dial desired call forward number
1/2/3/4 – unconditional/Busy calls/No answer calls/Busy or no answer calls5 – Station off-net, unconditional with speed bin.,6 – Station off-net, no answer with speed bin.,7 – Incoming outside line off-net (ATD only)8 – Station unconditional off-net with telephone number9 – Station No answer off-net with telephone numberTo make Call Forward to VMIB,
press # key after dialing call forward type 1~4To make off-net forward type 8 or 9,
press hook switch after entering telephone numberDial the station number or Hunt Group to forward incoming calls to,(Station : 100 ~ 151, Hunt Group : 620 ~ 629)Hang upTo cancel Call Forward, dial 5 5 4 and # or dial 5 5 9
6 DND (Do Not Disturb) Dial 5 5 3To cancel DND, dial 5 5 9
※ Note : Numbering plan code can be changed by Admin Programming 104 ~ 107, 109
SLT(Single Line Telephone)C. Terminal User Guide
Always Surpassing Customers Expectations39 LG-Nortel Confidential Information
D. ipLDK-60 IP Network Configuration Guide
Local IP Phone only Remote IP Phone
Router Fixed / Dynamic IP Fixed IP
ipLDK-60 Static IP Static IP
Sample 1 : Standalone Configuration for Local/Remote
Fixed Dynamic (DHCP)
Local Phone ipLDK-60 IP address ipLDK-60 IP address
Remote Phone ipLDK-60 IP address Router IP address
> Step 3 : (Remote) IP Phone configurationThe following table shows the methods of system IP setup of local IPphone and remote IP phone.
> Step 1 : Network connection for Internet access- Setup Router configuration to guarantee QoS for VoIP and IP address
: It depends on the existence of remote IP Phone to set the IP addressof Router to fixed or dynamic.
> Step 2 : Configuration of ipLDK-60The IP address of ipLDK-60 system always should be set to Static IPwhether Router gives fixed IP or not through DHCP function.And you have to choose and set the IP address of ipLDK-60 within the boundary of DHCP allocation table in Router.
The following table shows the IP allocation of Router and ipLDK-60.
※ Fixed IP : Public IP※ Static IP : Prescribed IP from user or public IP
Always Surpassing Customers Expectations40 LG-Nortel Confidential Information
D. ipLDK-60 IP Network Configuration Guide
Networking Configuration for ipLDK-60 systems
ipLDK-60 provides networking feature makes possible to operate one network among widespread systems.With this networking feature,
- All stations under each site can directly call the otherstations as if intercommunication.
- In general, Master has CO lines and every Slave can use those CO lines across the internet as if inner CO lines.
> Step 1 : Network connection for Internet access- Setup Router configuration to guarantee QoS for VoIP
> Step 2 : Configuration of ipLDK-60- All ipLDK-60 systems should have fixed IP address- Compose matrix table for the IP and setup those information
to each system with PC-Admin program
IP addressBranch A 192.168.1.2Branch B 192.168.1.2
For example, the following address will be set to each system.
IP AddressHeadquarter 192.168.1.1
Branch B 192.168.1.2
Headquarter Branch A)
A
BB
※ Teleworker- Set the system address of IP Phone to the IP address of
ipLDK-60 located in H/Q, Branch A and Branch B
Always Surpassing Customers Expectations41 LG-Nortel Confidential Information
D. ipLDK-60 IP Network Configuration GuideConfiguration for Carrier’s SIP Server
In this environment,system functions of ipLDK-60 cannot be used by remote SIP Phone.Only the functions provided by SIP server can be operable.
> Step 1 : Network connection for Internet access- Setup Router configuration to guarantee QoS for VoIP and
IP address: It doesn’t matter whether IP address for Router is fixed or not.
> Step 2 : Configuration of ipLDK-60The IP address of ipLDK-60 system always should be set to Static IP whether Router gives fixed IP or not throughDHCP function.So, you have to choose and set the IP address of ipLDK-60 within the boundary of DHCP allocation table in Router.
> Step 3 : IP Phone configurationSetup system IP of SIP Phone to the address of SIP server.