re. concrete beam plastered & painted,as per Strc. Eng details & specifications

220mm non-load bearing brick wall, plastered& painted as per Specialist details & specifications

DETAIL A-1

precast reinforced concrete lintel.

line of 10mm thick plaster,painted toarchitects approval

drip joint

precast reinforced concrete lintel.

drip joint

refer to door schedule

re. concrete pad foundation as per Strc. Engdetails & specifications, shown in dotted below

Loadbearing brickwork insuperstructure to be Corobrik

Imperial NFX 14 MPa nominalcompressive strength clay

bricks in Class II mortar.

Dulux Gloss Enamel alkyde paint (Colour :Ivory) to exterior cement plaster. Surface to beclean, dry and dust free with a moisturecontent of less than 15%.Prime surface withone coat Dulux Primer for New Plaster (Code:D192-0802) with an overcoating time of 18hours, undercoat with one coat DuluxUniversal Undercoat (Code: D196-0763) ith anovercoating time of 18 hours and finish withtwo coats Dulux Gloss Enamel (Code:D232-0734) with an overcoating time of 18hours.

Hard burnedengineered

foundation bricks

Gundle USB Green co ex 250µm damp proof membrane underconcrete surface beds to SANS mark 952-1985 type C laid withminimum 150mm overlaps and sealed with Gunplas pressuresensitive tape.

75Ø timber handrail (colour:

Ranier Oak D2242) fixed to

upright baluster as per

Specialist specifications.

Baluster paint specification as

per Structural Engineer -

colour Gun Metal Grey.

20Ø painted galvanised

mild steel rods welded to

upright baluster as per

Specialist specifications.

Paint specification as

per Structural Engineer -

colour Gun Metal Grey.

30x65mm painted galvanised

mild steel baluster welded to

baseplate as per Specialist

specifications.

Paint specification as per

Structural Engineer - colour

Gun Metal Grey.

180mm thick

post tensioned

concrete slab as

per Structural

Engineer's

specifications.

plastered

and painted

concrete

stair as per

Finishes

Schedule

reinforced concrete stair

as per Structural

Engineer's specifications.

1st Floor Landing

Halfway Landing

50 X 40 GMS hollow section

ballustrade posts with 15x15

gms square pin joint fixed to

concrete upstand beam and

pin fixed hand rail all to

engineers specification

Riser : 170

Tread: 250

REVISIONS

DATE NO. REVISION

OWNER'S SIGNATURE

01/04

STRIP SECTIONS

STUDIOWORK III

PROPOSED OFFICE BLOCK

KMY1501 OCT 2014

PROJECT TITLE

DRAWING TITLE

PROJECT No. DRAWING No.

SCALE DATEDESIGNED/DRAWN

1:20Y.SEWPERSAD

THIS DRAWING IS THE COPYRIGHT INTERLECTUAL

PROPERTY OF YOLANDA SEWPERSAD CANDIDATES CC.

AND MAY NOT BE COPIED, SHARED OR REPRODUCED

WITHOUT THE WRITTEN CONSENT.

21116563

STRIP SECTION A - A scale 1 : 20 STRIP SECTION B - B scale 1 : 20

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

PR

OD

UC

ED

B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTP

RO

DU

CE

D B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

re. concrete slab as per Strc. Engdetails & specifications

re. concrete pad foundation as per Strc. Engdetails & specifications, shown in dotted below

line of re. concrete column plastered & painted,as per Strc. Eng details & specifications

220mm non-load bearing brick wall, plastered &painted as per Specialist details & specifications

110Ø rwd in re. conc. column as per Strc. Eng'sspecifications and details with plaster and paintfinish as per finishes schedule

1000mm high balustrade incompliance with SANS 10400-D

DETAIL C -1

precast reinforced concrete lintel.

drip joint

One layer Derbigum SP4 waterproofingmembrane, with 75mm side laps and 100mm endlaps, sealed to primed surface to falls and crossfallsby 'torchfusion' finished with two coats Roofcotebeige acrylic paint. Waterproofing to be installedby an Approved Derbigum Contractor under a tenyear guarantee.

Screed laid to fall at 1:60

Saint Gobain Pipelines South Africa 100mm 180ºcentre bolt vertical roof outlet with flat grate code03805.

255mm thick concrete roof slab to engineers detailand specification.

DETAIL C - 2

REVISIONS

DATE NO. REVISION

OWNER'S SIGNATURE

02/04

DETAILED SECTIONS

STUDIOWORK III

PROPOSED OFFICE BLOCK

27 OCT 2014

PROJECT TITLE

DRAWING TITLE

PROJECT No. DRAWING No.

SCALE DATE DESIGNED/DRAWN

1:20/1:10 Y.SEWPERSAD

THIS DRAWING IS THE COPYRIGHT INTERLECTUAL

PROPERTY OF YOLANDA SEWPERSAD CANDIDATES CC.

AND MAY NOT BE COPIED, SHARED OR REPRODUCED

WITHOUT THE WRITTEN CONSENT.

KMY15

110Ø rwd in re. conc. column as per Strc. Eng's specificationsand details with plaster and paint finish as per finishes schedule

STRIP SECTION C - C scale 1 : 20 DETAIL C -2 scale 1 : 10

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

PR

OD

UC

ED

B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTP

RO

DU

CE

D B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

Line of re. concrete column plastered & painted as per Strc. Eng. details &specifications Colour : White

75mmØ painted galvanised mild steel handrail asper Specialist details & specificationsColour : Gun Metal Grey (RAL 9006)

60mmØ painted galvanised mild steel balustradeas per Specialist details & specificationsColour : Gun Metal Grey (RAL 9006)

Glazed aluminium shopfront with top hungopenings & waterproofing, to be powder coatedas per Specialist details & specificationsColour : Gun Metal Grey (RAL 9006)

600x600mm non-slip porcelain tiles laid on 20mmthick screed laid to fall, with expansion joints as perSpecialist details details & specificationsColour : White

Re. concrete slab as per Strc. Eng details &specifications

12mm plaster to be skimmed to a smooth surface& to painted as per Specialist details &specificationsColour : White

REVISIONS

DATE NO. REVISION

OWNER'S SIGNATURE

03/04

DETAILED SECTIONS

STUDIOWORK III

PROPOSED OFFICE BLOCK

27 OCT 2014

PROJECT TITLE

DRAWING TITLE

PROJECT No. DRAWING No.

SCALE DATE DESIGNED/DRAWN

1:10 Y.SEWPERSAD

DETAIL A-1 scale 1 : 10

DETAIL C-1 scale 1 : 10

THIS DRAWING IS THE COPYRIGHT INTERLECTUAL

PROPERTY OF YOLANDA SEWPERSAD CANDIDATES CC.

AND MAY NOT BE COPIED, SHARED OR REPRODUCED

WITHOUT THE WRITTEN CONSENT.

KMY15

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

PR

OD

UC

ED

B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTP

RO

DU

CE

D B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

900

1800

900

450

2700

2100

2100

860

1730

860

600

2100

600

1200

1500

600

2100

800

600

1200

2100

2700

900900 900

2100

1500

450

2100

900

REVISIONS

DATE NO. REVISION

OWNER'S SIGNATURE

04/04

SCHEDULES

STUDIOWORK III

PROPOSED OFFICE BLOCK

KMY1527 OCT 2014

PROJECT TITLE

DRAWING TITLE

PROJECT No. DRAWING No.

SCALE DATEDESIGNED/DRAWN

1:100Y.SEWPERSAD

NOTES IN RESPECT OF S.A. STANDARD CODE OF PRACTICE FOR THEAPPLICATION OF THE NATIONAL BUILDING REGULATIONS (N.B.R.) SANS10400

PART D - PUBLIC SAFETYALL BALUSTRADES TO COMPLY WITH PART DD2PART M - STAIRWAYSDIMENSIONS OF STAIRWAYS TO BE IN ACCORDANCE WITH MM2 &BALUSTRADES TO COMPLY WITH MM3PART N - GLAZINGALL GLAZING TO COMPLY WITH PART N-N.B.R.PART 0 - LIGHTING AND VENTILATIONALL AREAS TO BE ARTIFICIALLY LIT IN COMPLIANCE WITH 006, OFFICES &OTHER HABITAL ROOMS MIN. 350lux, TOILETS 160luxALL AREAS TO BE MECHANICALLY VENTILATED IN ACCORDANCE WITH007 - FRESH AIR TO BE SUPPLIED AT A RATE OF 7,5l/s/p & TOBE UNIFORMALLY DISTRIBUTED THROUGHOUT HABITAL AREAS.AIR VELOCITY NOT TO EXCEED 0,5m/s TO OFFICES & SHOPS

PART S - FACILITIES FOR DISABLED PERSONSRAMPS TO BE PROVIDED IN ACCORDANCE WITH SS2TOILET FACILITIES TO BE PROVIDED IN ACCORDANCE WITH SS5PARKING BAYS TO COMPLY WITH SS8SIGNAGE TO COMPLY WITH SS9PART U - REFUSE DISPOSALREFUSE AREA TO BE CONSTRUCTED & PROVIDED WITH HOSE,BIBTAP & SUMP

PART T - FIRE PROTECTIONOCCUPANCY CLASSIFICATION TO COMPLY WITH B2 &F2ALL MATERIALS TO COMPLY WITH TT5ALL STRUCTURAL ELEMENTS AND COMPONENTS TO COMPLY WITH TT7.

LL OPENINGS TO BE PROTECTED IN COMPLIANCE WITH TT10ALL ACCESS DOORS TO EMERGENCY ROUTES TO BE SABS CLASS B2 HOUR RATED. DOORS FIT WITH SELF-CLOSING DEVICE TT10.4 & LOCKS INACCORDANCE WITH TT19.9.ALL CEILING MATERIALS TO COMPLY WITH TT13ALL FLOOR COVERINGS TO COMPLY WITH TT14ALL WALL FINISHES TO COMPLY WITH TT15LOCKS TO ESCAPE AND ACCESS DOORS TO COMPLY WITH TT19.9STAIRWAYS FORMING ESCAPE ROUTES TO COMPLY WITH TT23ALL OPENINGS IN FLOORS TO COMPLY WITH TT26SIGNAGE TO BE PROVIDED IN ACCORDANCE WITH TT29,TT32, TT55.4 & TT55.5EMERGENCY ROUTES TO BE LIT IN ACCORDANCE WITH TT30 - DESIGNED BYPROF. ENGINEER & CERTIFIED ON COMPLETIONFIR DETECTION AND ALARM SYSTEM TO BE PROVIDED IN ACCORDANCE WITHTT31 - TO BE CERTIFIED BY PROFESSIONALSPRINKLER SYSTEM TO BE PROVIDED IN ACCORDANCE WITH TT33/36

FIRE RETICULATION TO COMPLY WITH TT33 & WW5HYDRANTS TO BE PROVIDED IN ACCORDANCE WITH TT35PORTABLE FIRE EXTINGUISHES TO BE PROVIDED IN ACCORDANCE WITHTT37ANY ACCESSIBLE CONCEALED SPACE WITH A MAX. DIMENSION OF5M TO BE FIRE STOPPED IN ACCORDANCE WITH TT39SERVICE PIPES, CONDUITS AND SLEEVES TO COMPLY WITH TT41

OCCUPANCY : OFFICE - G1 STORAGE - J3FIRE HOSE REELS TO COMPLY WITH TT3725mm dia. WATER SUPPLY TO ALL FIRE PROTECTION COMPONENTS3% ROOF VENTILATION TO BE PROVIDED TO N.B.R.MAX. HEIGHT OF STORAGE = 3M

DRAINAGE NOTES- ALL WORK IS TO COMPLY TO SANS 10400- HEAD OF DRAIN IS TO BE VENTED- ANY DAMAGED FITTINGS TO BE REPLACED- ALL GULLEY SURROUNDS & MANHOLE COVERS TO BE 75 mm ABOVE GROUND LEVEL- SEWER MANHOLES TO BE EXPOSED BEFORE COMMENCING WORK AND ADJUST LEVELS ACCORDINGLY- IE'S TO ALL BENDS AND JUNCTIONS- SOIL PIPES TO BE 110 diameter PVC- SEWER UNDER BUILDINGS TO BE 110 mm UPVC RIBBED PTPE- ANCHOR BLOCKS TO BE USED WHEN GRADIENTS EXCEED 1:5

FLASHING TO COMPLY WITH PART LL5.2TWO COURES OF BRICKWORK TO BE REINFORCEDWITH BRICKFORCE BELOW WALL PLATE LEVEL, ABOVEWINDOW HEAD HEIGHT & BELOW WINDOW CILL LEVEL.EXTERNAL FACE OF INNER SKIN OF ALL EXTERNALWALLS TO BE BAGGED AND WATERPROOFEDWITH TWO COATS OF BITUMEN PAINT.6.4 mm GYPSUM CEILING BOARDS FIXED TO 38 X 38BRANDERING AT MAX 300mm CENTRES BOTH WAYS.

375 mic DPC TO BE PROVIDED TO WALLS AT SLABLEVEL AND UNDER ALL CILLS.

CONTRACTOR TO ENSURE THAT NO CHANGES INLEVELS ARE MADE OVER LOCAL AUTHORITYSERVITUDES OR UNDER GROUND SERVICES UNLESSPERMISSION HAS BEEN GIVEN IN WRITING BYTHE LOCAL AUTHORITY.ANY DISCREPANCIES AND OMISSIONS ARE TO BEBROUGHT TO THE ARCHITECTS ATTENTIONIMMEDIATELY.

IF ON EXCAVATION THE SITE IS FOUND TOCONTAIN EXPANSIVE CLAY, SHALE, GROUND WATEROR OTHER SUSPECT SOIL CONDITIONS : THEN ALLFOUNDATIONS ARE TO BE BUILT TO PROFESSIONALENGINEERS DETAILS & UNDER HIS SUPERVISION.

NOTE: ALL DIMENSIONS - LEVELS ETC. ARE TO BE VERIFIED ON SITEPRIOR TO ANY WORK BEING PUT IN HAND AND TO REPORT ANYDECREPANCIES IMMEDIATELY TO THE ARCHITECT.ALL MATERIALSAND LABOUR PRACTICE IS TO COMPLY WITH PART-B OF SANS10400 AND NATIONAL BUILDING REGULATIONS.THIS DRAWINGOR ANY PORTION THEREOF IS RESERVED BY THE ARCHITECT ANDMUST NOTBE RE-PRODUCED IN ANY FORM WITHOUT CONSENT

SUB-FLOOR AND FOUNDATION TRENCHES TOBE POISONED WITH "CLORODANE" SOLUTIONIN ACCORDANCE WITH SABS CODES OFPRACTICE BY SPECIALIST.

GENERAL NOTESALL WORK TO COMPLY WITH SANS 10400.CORNER BEACONS TO BE LOCATED ANDEXPOSED BEFORE WORK ON SITECOMMENCES.CONTRACTOR TO CHECK ALLDIMENSIONS AND LEVELS (SCHEDULES ANDDETAILS) BEFORE THE RELEVANT WORK ISPLACED IN HAND AND REPORT ANYDISCREPANCIES TO THE ARCHITECT.ALL WRITTEN DIMENSIONS TO BE TAKEN INPREFERENCE TO SCALING.SOIL TO BE WELL COMPACTED BEHIND INLAYERS NOT EXCEEDING 150 mm.ALL FOUNDATIONS TO BE TAKEN BELOWNATURAL GROUND LEVEL.NO BACK FILLING OF OVER EXCAVATEDAREAS WILLBE PERMITTED.

THE CONTRACTOR IS TO INSPECT THEOFFICIAL APPROVED COPIES OF THEDRAWINGS TO ENSURE THAT ALLAMENDMENTS HAVE BEEN TAKEN INTOACCOUNT .THE ATTENTION OF THEOWNER/CONTACTORIS DRAWN TO THE FACTTHAT CHANGERS TO THE PLAN&/ORSPECIFICATION AFTER OFFICIAL APPROVALIS LIKELY TO INVALIDATE THAT APPROVAL.ALL EARTHWORKS TO BE CONTAINED WITHINSITE BOUNDARIES & WITHIN 1.0 m OF ANY ofANY BOUNDARY.BANKS TO BE CUT AT AMAXIMUM OF 26 degrees.

NATURAL GROUND LINE IN APPROXIMATEPOSITION ONLY & NO CLAIM CAN BE MADEFOR ANY DISCREPANCIESON SITE.

SCHEDULE OF AREAS

SITE AREA 14.450 sq.m.

ZONING COMMERCIAL

COVERAGE 0.039% OF 13773

P R O P O S E D W O R K

PARKING REQUIREMENT/PROVISION

F.A.R GROUND AREA 274.94

F.A.R FIRST FLOOR AREA 274.94

F.A.R ROOF AREA 274.94

TOTAL F.A.R 824.82

INDUSTRIAL - 1 Loading bay/1000sq.m (G.L.A.)

OFFICES - 1 bays/100sq.m. (G.L.A.)

THIS DRAWING IS THE COPYRIGHT INTERLECTUAL

PROPERTY OF YOLANDA SEWPERSAD CANDIDATES CC.

AND MAY NOT BE COPIED, SHARED OR REPRODUCED

WITHOUT THE WRITTEN CONSENT.

FLOOR FINISH: ABLUTIONSMOSAIC TILES LOCATION:

SPECIFICATION: PREPARE SHOWER FLOORS TO RECEIVE NEW 50 x 50mm MOSAIC TILES TO LATER SPECIFICATION.SHOWER FLOOR TILING TO BE FLUSH WITH BATHROOM FLOOR TILING AND TO FALL TO CENTRAL SHOWERDRAIN AND BRASS SHOWER TRAP (SHOWER FLOOR TO BE RECESSED +-30mm LOWER THAN BATHROOMFLOOR SLAB TO ACCOMMODATE THE FALL OF THE SHOWER FLOOR TILES)SHOWERS TO BE WATERPROOFED WITH TAL SUPERFLEX 1 AS PER MANUFACTURERS SPECIFICATIONS.TILING MATERIALS AND INSTALLATION METHODS (BACKGROUND, ADHESIVES, GROUT AND MOVEMENTJOINTS TO BE IN STRICT ACCORDANCE WITH TILING SPECIFICATION DRAWING NUMBER 0027-06-500t,0027-06-500u AND DRAWING NUMBER 0027-06-500v IN THIS FINISHES SCHEDULE.

LOCATION:

FLOOR FINISH:

FLOOR FINISH:

LOCATION:

SPECIFICATION:

SPECIFICATION:

PREPARE FLOOR TO RECEIVE NEW 330 x 330mm GRADE 1 CERAMIC TILES CODE: AG 705 , COLOUR:

BEIGE BY TILE AFRICA (PHONE: YVONNE DALTON 082 455 1343).

ALL TILES TO BE FROM THE SAME BATCH

GROUT: 5mm JOINT, COLOUR: LIGHT GREY

MOVEMENT JOINTS:

SURESTRIP 'SUPVCMJ10' 10mm PVC MOVEMENT JOINTS, FITTED WITH 6mm WIDE LIGHT GREY COLOUR

POLYURETHANE INFILL TO SUIT TILING, FIXED AS PER MANUFACTURER'S SPECIFICATIONS.

TILING MATERIALS AND INSTALLATION METHODS (BACKGROUND, ADHESIVES, GROUT AND MOVEMENT

JOINTS TO BE IN STRICT ACCORDANCE WITH SPECIFIC SPECIFICATION DRAWING NUMBER ......

PREPARE FLOOR TO RECEIVE MINIMUM 20mm

THICK SAND/ CEMENT SCREED , COMPRISING

ONE PART CEMENT TO FIVE PARTS SAND.

SCREED TO FALL TO FULLBORE OUTLETS

ROOFSCREED

FLOOR FINISH:

SPECIFICATION: PREPARE POWERFLOATED FLOOR SLAB, UNPOLISHED AND UNTREATED, TO RECEIVE NEW 300 x 300mm

NON SLIP PORCELAIN TILES CODE: DARC 3211 YD , COLOUR: BEIGE

WITH 300 x 300mm NON SLIP PORCELAIN TILE CODE: DARC 3213 YD, COLOUR: CHARCOAL

AS INDICATED ON DETAIL PLANS 2277-01-200-304-C, ALL AS SUPPLIED BY FERREIRAS DECOR WORLD

OFFICESNON SLIP PORCELAIN TILES

RECEPTION AREASCERAMIC TILES LOCATION:

FINISHES SCHEDULE

VAAL SANITARYWARE TUSCANY WHITE VITREOUS CHINA CLOSE COUPLED WASHDOWN SUITECOMPRISING 90º OUTLET CLOSED RIM PAN (PRODUCT CODE 772800) AND MATCHING 7 LITREPUSH-BUTTON TOP DUAL FLUSH CISTERN (PRODUCT CODE 711139) INCLUDING LID AND FITMENTS,WITH PURPOSE-MADE DOUBLE FLAP WOODEN SEAT (PRODUCT CODE 8606Z0 "TUSCANY") .COBRA WATERTECH CAPSTAN 15MM UNDERTILE STOPTAP WITH SLIDING WALL FLANGE IN CHROMECODE (CS-228-15CP).

VAAL SANITARYWARE 510 X 405MM HIBISCUS WHITE VITREOUS CHINA LAVATORY BASIN (CODE : 7023)WITH ONE TAPHOLE INCLUDING INTEGRATED OVERFLOW AND CHAINSTAY HOLE, BOLTED TO WALLWITH TWO X 10MM BOLTS (PRODUCT CODE 8448Z0) AND INCLUDING CLASSIC FLOOR MOUNTEDPEDESTAL (PRODUCT CODE 7150). COBRA WATERTECH CAPSTAN 15MM ONE TAP HOLE BASIN MIXERWITH CAST FIXED OUTLET, POP-UP WASTE, MOUNTING KIT AND ANGLE VALVES IN CHROME CODE(CS-293CP).PLUMBCRAZY RUBBER 40 X 40MM PLAIN P-TRAP (CODE YA4).

PLEXICOR BAR 100W POLISHED STAINLESS STEEL WALL MOUNTED HEATED TOWEL RAIL, OVERALL SIZE550 X 700MM HIGH WITH 9NO. STRAIGHT CROSSBARS, PLUGGED AND SCREWED TO WALL USINGSTAINLESS STEEL SCREWS AND CONNECTED TO 230V ELECTRICAL POINT.

POSITION TO BE CONFIRMED BY ARCHITECT PRIOR TO FIXING

FRANKE QUINLINE MODEL QLX621-120 GRADE 304 18/10 POLISHED STAINLESS STEEL INSET SINK WITHDRAINER ON LEFT HAND SIDE (CODE: 820008), SIZE 1200 X 500MM WIDE WITH TWO 410 X 343 X167MM DEEP AND 315 X 324 X 152MM DEEP BOWLS, FITTED ONTO SCULLERY COUNTER INCLUDING90MM WASTE FITTINGS (CODE: 300651) AND PVC TRAPS. SINK COVERED WITH PROTECTIVE PLASTICCOATING WITH 25 YEAR GUARANTEE AGAINST CORROSION.(CONFIRM THAT DRAINER IS ON LEFT HAND SIDE OF SINK PRIOR TO PLACING ORDER)INCLUDE PLUG AND CHAIN.

COBRA WATERTECH STRATA SINGLE LEVER 15MM CHROME SINGLE TAP HOLE SINK MIXER WITHTUBULAR SWIVEL OUTLET, MOUNTING KIT AND ANGLE VALVES (CODE: SA-870), MANUFACTURED INACCORDANCE WITH SANS 1480:2005 (BS EN 1286).

QUANTITY:

SPECIFICATION:

6ABLUTIONS

SANITARY SCHEDULE

LOCATION:

LOCATION:

LOCATION:

LOCATION:

FITTING DESCRIPTION: WC

QUANTITY: 10ABLUTIONS FITTING DESCRIPTION: WHB

QUANTITY: 8ABLUTIONS FITTING DESCRIPTION: RAILS( PARAPLEGIC)

QUANTITY: 3KITCHEN AND TEA AREA FITTING DESCRIPTION: SINK

SPECIFICATION:

SPECIFICATION:

SPECIFICATION:

21116563

DISABLED VAAL SANITARYWARE TUSCANY WHITE VITREOUS CHINA CLOSE COUPLED WASHDOWNSUITE COMPRISING 90º OUTLET CLOSED RIM PAN (PRODUCT CODE 772800) AND MATCHING 7 LITREPUSH-BUTTON TOP DUAL FLUSH CISTERN (PRODUCT CODE 711139) INCLUDING LID AND FITMENTS,WITH PURPOSE-MADE DOUBLE FLAP WOODEN SEAT (PRODUCT CODE 8606Z0 "TUSCANY") .COBRA WATERTECH CAPSTAN 15MM UNDERTILE STOPTAP WITH SLIDING WALL FLANGE IN CHROMECODE (CS-228-15CP).

QUANTITY:

SPECIFICATION:

4ABLUTIONSLOCATION: FITTING DESCRIPTION: WC(PARAPLEGIC)

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

PR

OD

UC

ED

B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT

PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCTP

RO

DU

CE

D B

Y A

N A

UT

OD

ES

K E

DU

CA

TIO

NA

L P

RO

DU

CT