1/4
Su-30 Flanker G interior S.A.
32 660
32 6601/32 scale detail set for Trumpeter kit • sada detailù pro model 1/32 Trumpeter
ORIGINAL KIT PARTSPÙVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANÌNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PØED SLEPENÍM
P3
21
50
2 pcs
2 pcs
41
D51
14
35
= 3mm
2 sets
Cockpit
P38
P29
Film
P21 P22
18
17
P25 P24
P20 P19
15
16P23 P26
17 ( 16 )
Cockpit44
2 sets
2 pcs
D39 ( R22)
5
2 sets
13
l = 3mm
plastic= 1mm
7
R5
6
1
4
10
2/4 32 660
25
D30
D29
D29, D30, K1
Fuselage
40
24
3823
38
20
22
40 24
3823
22
38
20
R21
48
Film
18
24
Cockpit
Fuselage
7
13
l = 3mm
plastic= 1mm
R6 8
2
9
3
R20
12
11
11
29
37
37
3/4 32 660
Correct position !
19
D50
263 pcs PE6
262 pcs PE6
Correct position !
19
P42
17
19
Cockpit
Fuselage
52
51
Fuselage
278 pcs
288 pcs
45 46
Canopy
P28
Canopy
47
39
36
49
43
32
3342
30
34
31
3 pcs
3 pcs42
2 pcs
Canopy
47
39
43 43
30 30
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem pøilepíte, pøi pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na èásti dílù, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.1.Samolepící díly oddìlujte od rámeèku na podkladovém papíøe. Po oddìlení je sejmìte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.4. Samolepící díly berte za hrany nebo za èásti, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will by permanently affixed when pressed onto its intended location, its location can be adjusted.5. Díl lehce položte do pozice, ve které má být nalepen. Upravte pøesnou pozici a pøimáèknìte. Díl dokonale pøilne až po pøimáèknutí, pøed pøimáèknutím lze dílem opatrnì manipulovat.
4/4 32 660
© EDUARD M.A. 2010 www.eduard.com Made in Czech Republic
PARTS WITH GLUE . DÍLY OPATØENÉ LEPIDLEM